10.5.3 cripples Time Capsule

Hi,
What do you do as a consumer when you've payed for a Time Capsule and want to return it to Apple even though its working flawlessly under 10.5.2 but stopped working correctly under 10.5.3?
See description on following link:
http://badtastic.com/stuff/crippled.jpg
Any advice?
Kind Regards / Badtastic

Thanks a lot for your answer !
Your tip led to solving the problem which I will now take the opportunity to share since I'm sure there are others out there who's hair is turning grey trying to figure out why their TM backup routines are failing.
1) Perform a "Verify Disk" with the Disk Utility.
2) If you see "Nesting of folders has exceeded the recommended limit of 100" Bingo! you've identified the cause.
In my case it turned out to be a folder that was the result of an old (failed) Automator experiment" that created a folder within a folder within a folder etc. in the "Downloads" folder that for some reason created a nested heirarchy going into the hundreds.
anyway...
4) Delete the offending folder and empty the trash, make sure the folder is gone. Perform a verify disk again to make sure you dont get any "Nesting of folders has exceeded the recommended limit of 100" marked in RED
5) Performed a Time Machine - Time Capsule backup again which this time completed successfully
Conclusion:
For some unknown reason, the same offending folder did not cause TM to fail under 10.5.2 but it did make TM to fail under 10.5.3 It seems if you have any folders who's internal nesting hierarchy exceeds 100 present on your system under 10.5.3 your TM backup is almost guaranteed to fail at the exact point during the backup when TM comes across and try's to process that land mine of a folder. Bottom line: 10.5.3 is (unlike 10.5.2) sensitive to such folders.
Hope this helps
Cheers / Badtastic

Similar Messages

  • Extending Wireless Network Is Crippling Data Speeds - Time Capsule 802.11ac

    Just set up a new Time Capsule (3TB ac) to replace my older 2TB dual-band TC. I had successfully been running a network with another dual-band Airport Extreme (bought this year/the model before current one) extending from the older TC.
    Now when I extend the network using my new TC and the same, older AE, the whole networks grinds down severely. Most times, pages dont even start to load for 10-20 seconds, and then I watch the load up slowly.  Testing the speed on Speedtest, the data seems to stop and start a few times, sometimes peaking at around 30Mbpsm but the rate is all over the place.
    The second I turn the wireless Network Mode to "Off" on the AE, the system comes right back up and Im getting my constant 60 Mbps.
    Im up to date on all firmware.
    Running OSX 10.9
    This is a days old iMac 27" i7
    Something seems seriously wrong here and Im at a loss for figuring it out. I was hoping the new range of the TCs would allow me to get rid of the extending AE altogether, but even in my modest sized home, the network is sketchy from the opposite end of the house. So unfortunately, Im going to have to figure something out here. I really hoping the answer isnt to buy a new AE with ac.

    You are aware that you must completely reset a cable modem whenever you change the device that is connected to the modem, correct?
    The cable modem may need a power down period of up to 30 minutes, sometimes longer.
    The reason for this is that the cable modem associates with the first device that it connects with. If you connect another device, the cable modem "remembers" and "looks" for the old device. When it does not see it....because it is no there.....it refuses to give out an IP address to the "new" device.
    The trick is make the cable modem "forget" the original device, so it will associate with a new device.
    If you want to try the 802.11ac product, see this excellent User Tip provided by forum expert Tesserax for the correct setup.
                     AirPort - Complete Power Recycle

  • Remote access my time capsule when mobile me is no longer offered? And I do NOT have a static IP?

    How can i remote access my time capsule when mobile me is no longer offered iCloud is months away and I do NOT have a static IP?
    I feel that apple has crippled the functionality of my time capsule as I can no longer access the files abroad!

    Try the advice in this thread.

  • Time Capsule: How can one limit size of Time Machine Backup?

    So there appears to be no easy way of partitioning the hard drive in Time Capsule. If this is so how does one limit the size of the Time Machine backups folders?
    I want to use the hard drive to act as a normal storage device for various files but I understand that Time Machine will keep on increasing the size of the backups folder until it eventually runs out of space on the hard drive partition. Since one cannot re-partition the hard drive how can Time Machine be allotted only a specific portion of the hard drive? I don't want the hard drive to be filled with Time Machine backup folders.

    Thanks BSP. Yes I am aware of the ability to limit the folders that TM backs up. I use this capability, But that certainly is not the solution I want.
    I have not bought Time Capsule and probably will not buy it unless Apple fix this 'problem' and make the hard drive in TC behave like any other hard drive.
    Why is it that Apple comes up with innovative designs which are let down by being 'crippled' in some way? Apple TV is another good example; can you steam from DVD Player? No. Can one steam a presentation directly from Keynote? No. With a little more thought Apple's products would be great. But, alas, this is not the case.

  • Wireless printing with Brother - Time capsule

    I try to get my printer Brother DCP-J715W up and running, but I can't connect to the router, Time Capsule.
    Any suggestions? Is it a problem with WPS or AOSS, don't know exactly what it is, but that's what the error report says ...
    Tx, Aldert

    Using extend a wireless network on a TC wirelessly is a major no no and I quote from the web
    Wi-Fi extenders (sometimes called wireless repeaters) seem like the obvious choice for helping a wireless router cover an entire house with Internet access. Essentially, they pick up a wireless signal just like your tablet or laptop, then rebroadcast that signal, giving you a second access point to connect to. But there’s a big problem with that which kind of cripples the functionality of extenders. Networking expert Tim Higgins wrote this about extenders on SmallNetBuilder in 2011:
    “No matter what they are called or technology they use, repeaters start out with a minimum 50% throughput loss. The reason is that a repeater must receive, then retransmit each packet using the same radio on the same channel and with the same SSID. If the repeater is very efficient, then your loss will be close to 50%. But if it’s not, throughput loss can be higher.”
    This is why I think you have to restart with cabling to the TCs

  • Time Capsule: Connectivity loss when starting backups

    Ever since getting my Time Capsule, I've noticed sporadic dropouts on my VOIP line and when video-conferencing. There are periods of a few seconds when others cannot hear me, or conversely I cannot hear them. With video conferencing, the connection will stutter - then finally cut out completely. I also see occasional "burps" with my internet connectivity, where sites do not respond briefly, then with a reload be fine. I had just written it off as standard network jitter or other problems, but it's gotten annoying enough to investigate.
    I finally figured it out - whenever a Time Machine backup begins, my connectivity to the internet drops for a few seconds. I'm not sure if this is just when the drive is spinning up, or something to do with actually commencing a backup. With three Macs in the house all backing up, this happens with some regularity and it's pretty annoying.
    Is anyone else seeing this? I use the Time Capsule as my central router, and it's running an N-only network. My MacBook Pro connects to it via (N), my wife's MacBook is on (G) connected through another Airport Extreme, and the Mac Mini is on gigabit ethernet. I'd be glad to provide any further detail.

    This continues to be crippling. In fact, with multiple computers on the network, I can count on my connection being interrupted about every 10-15 minutes. VOIP calls die, video conferencing dies, online games become useless. All because the Time Capsule is a flawed product that cannot walk and chew gum at the same time.
    Given Apple's extremely lackluster history of updates, support, and communication, I don't expect this will ever be fixed. And I don't expect I will ever buy another Apple networking product (after having three Airport Base Stations, an Airport Express, and now a Time Capsule).

  • Airport can no longer read or write the configuration of Time Capsule

    I have a MacBook Pro running OSX 10.8.3 and maintained with all available patches. I have also a Time Capsule with version 7.6.3 of the firmware. I use AirPort 6.2. So everything seems to be updated with the latest versions.
    This has really been a good setup for nearly a year now, but earlier this month Time Machine suddenly stopped to work and could no longer do backups to the Time Capsule. I have tried to factory reset the Time Capsule several times, but I still get problems when writing the configuration to the Time Capsule. I get an error message saying "An error occurred while updating the configuration".
    Airport is furthermore not able to detect the Time Capsule correctly anymore, so I have to configure it by entering the IP address. But after setting up WLAN, disks, etc. and enhanching the security, I just receive the error message when I try to write the config. The Internet connection works perfectly anyway, both via cable and wireless.
    Anyone got any tips?

    Do the setup by ethernet in full isolation from the network.
    Start from a full factory reset.
    I would recommend you take the firmware back to 7.6.1 or even earlier if the TC is older than 12months. 7.5.2 was very reliable. All these bugs started with 7.6 and the change to Lion.
    I would also recommend installing 5.6 utility.
    How to load 5.6 into ML.
    1. Download 5.6 for Lion.
    http://support.apple.com/kb/DL1482
    Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
    2. Download and install unpkg.
    http://www.timdoug.com/unpkg/
    Run unpkg on the desktop.. it is very simple.. drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. drill down.. applications utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
    You cannot uninstall 6.1 (now 6.2 if you updated) so don't try.. and you cannot or should not run them both at the same time.. so just ignore the toyland version.. the plastic hammer.. and start using 5.6.. a real tool.
    For screen shots see this post.
    https://discussions.apple.com/thread/4668746?tstart=0

  • In order to create space on my MBA I just bumped iTunes media to G drive linked through Time Capsule.  Now pointed iTunes at new iTunes libary on G drive and, even though all music files are there, iTunes can only 'see' 10 albums. Any help appreciated.

    Bit more detail...
    Mac Book Air has been struggling for space for a while so I bough at time capsule a) for back up and b) to host my itunes folder remotely.  This didnt' work.  I took it into the Genius bar and the genius there told me that time capsule is not designed for anything other than back up.  Instead I have to connect a G drive through the time capsule's wireless router to my MBA. 
    I followed his instructions - moved my files from the Time Capsule and MBA directly onto the G Drive - which took a heartening 2 hrs so something must have been happening - and the held down 'Alt' when starting iTunes and selected the new itunes folder as the location of my itunes libarary which I wanted iTunes to 'point at'.  When I opened iTunes only 10 albums are visible now.
    In ITunes advanced preferences it says it is pointing at the correct folder.  The files are all cleary there when I open the G Drive folder to take a look.  But I cannot get iTunes to find them.
    Any suggestions? 
    Secondary challenge - in spite of deleting the original itunes folder on my MBA I still get messages pop up telling me my start up disk is out of space and I need to clear some - I expected to stop getting this message now I had done this exercise above.  I have emptied Trash.  Again - any pointers appreciated.  I am new to this world of 'intuitive' macbooks.
    Cheers

    After admittedly only a quick read the one thing you don't say is how you are trying to make this move.  Most people with moving library issues do it the wrong way.  Plenty of web sites tell you how to do it the wrong way.
    If the iTunes application is started before the drive with the library is fully mounted and awake iTunes will revert back to the internal drive.

  • How do I use my Time Capsule with hotel wired internet

    How do I use my Time Capsule as a wireless router on my hotel free internet ethernet cable?

    It may not be possible..
    If they use a web access page, then there is no way you can set the TC to authenticate.. you must use the computer to authenticate and then use the computer to bridge to the TC for wireless clients to access.
    Look up instructions on using ICS (internet connection sharing) in the Mac.
    eg for 10.6.8 http://support.apple.com/kb/PH6589
    eg http://support.apple.com/kb/PH10740
    Of course if there is no login then you could just use it.. but I doubt you would be asking if it just worked.

  • Forgot password to access my Airport Time Capsule, can't restore Time Machine backup

    It is stupid, I know, but after the first time I setup Time Machine in my Airport Time Capsule (6 months ago) i never had to use the password because it stayed stored in my Keychain.
    Anyway, couple days ago I had to format the hard drive of my MacBook Pro and I did it thinking that I had a complete data backup stored in my Airport Time Capsule (encrypted data). It was late when I realized that I did not have the password written/stored anywhere. Nothing to do about it, just move on and start all over again.
    I need to clean up my Airport Time Capsule and set it to factory default. I already accepted that I will lose all my data and it is okay. So far all I found was how to reset the wifi user/password but nothing about deleting stored data or reset to factory default without having the encrypted password. Can you please help me? Thanks in advance!  

    The encrypted data is not related to the Time Capsule.. that is purely Time Machine.
    Very sorry for you.. it is one big danger when you encrypt.
    Reset to factory.
    Factory reset universal
    Power off the TC.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the TC to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
    N.B. None of your files on the hard disk of the TC are deleted.. this simply clears out the router settings of the TC.
    Wipe the hard disk. Open the airport utility go to the disk tab. Click on erase disk.
    Select just quick erase.. it just deletes the file table and is not secure but fine for your purposes.

  • I want a new and more powerful (non-Apple) wireless router but I still want to use my existing Time Capsule to continue with my Time Machine backups and I still need the Time Capsule's Network Attached Storage (NAS) features and capabilities

    THE SHORTER STORY
    My goal is to successfully use my existing Time Capsule (TC) with a new and more powerful wireless router. I need a new and more powerful wireless router in order to reach a distant Denon a/v receiver that is physically located in a master bedroom some 50 feet away from my modem. I need to provide this Denon a/v receiver with an Internet connection so that it can obtain its firmware updates and I need to connect this Denon a/v receiver to my network in order to use its AirPlay feature. I believe l still need the TC's Network Attached Storage (NAS) features because I am not sure if the new wireless router will provide me with the NAS like features / capabilities I need to share files between my two Apple laptops with OS X 10.8.2. And I know that I absolutely need my TC's seamless integration with Apple's Time Machine (TM) application in order to continue to make effortless backups of my two Apple laptops. To my knowledge nothing works with TM like Apple's TC. I also need the hard disk storage space built into the TC.
    I cannot use a long wired Ethernet cable connection in this apartment and I cannot use power-line adapters. I have read that wireless range extenders and repeaters are difficult to successfully set-up and that they will reduce data speeds, especially so when incorrectly set-up. I cannot relocate my modem and/or primary base station wireless router.
    In short, I want to use my TC with my new and more powerful wireless router. I need to stop using the TC to connect to the modem. However, I still need the TC for seamless TM backups. I also need to use the TC's built in hard drive for storage. And I may still need the TC's NAS capabilities to share files wirelessly between laptops because I am assuming the new wireless router will not provide NAS capabilities for OS X 10.8.2 (products like this/non-Apple products rarely seem to work with OS X 10.8.2/Macs to provide NAS features and capabilities). Finally, I want to continue to use my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also want to continue to use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Can someone please advise on how to set-up my new Asus wireless router with my existing TC in such a way to accomplish all of this?
    What is the best configuration or set-up to accomplish my above goals?
    Thank you in advance for your assistance!!!
    THE FULL STORY
    I live in an apartment building where my existing Time Capsule (TC) is located in my living room and serves many purposes. Specially, my TC is at least all of the following:
    (1) Wi-Fi router connected to Comcast Internet service via Motorola SB6121 cable modem - currently the TC is the Wi-Fi base station that connects to the modem and has the gateway address to the Internet. The TC now provides the DHCP service for the Wi-Fi network.
    (2) Wireless router providing Internet and Wi-Fi network access to several Wi-Fi clients - two Apple laptop computers, an iPod touch, an iPad and an iPhone all connect wirelessly to the Internet via the TC.
    (3) Wired Ethernet router providing Internet and Wi-Fi network access to three different devices - a Panasonic TV, LG Blu-Ray player and an Apple TV each use one of the three LAN ports on the back of the TC to gain access to the Internet.
    (4) Primary base station in my attempt to extend my wireless network to a distant (located far away) Denon a/v receiver requiring a wired Ethernet connection - In addition to the TC, which is my primary base station, I am also using a second extended Wi-Fi base station (a Netgear branded product) to wirelessly extend my WiFi network to a Denon receiver located in the master bedroom and requiring a wired Ethernet connection. I cannot use a wired Ethernet connection to continuously travel from the living room to the master bedroom. The distance is too great as I cannot effectively hide the Ethernet cable in this apartment.
    (5) Time Machine (TM) backup facilitator - I use my TC to wirelessly back-up two Apple laptops using Apple's Time Machine (TM) application. However, I ran out of storage space on my TC and therefore added external storage to it. Specifically, I added an external hard drive to my TC via the USB port on the back of the TC. I now use this added external hard drive connected to the TC via USB as the destination storage drive for my TM back-ups. I have partitioned the added external hard drive, and each of the several partitions all have enough storage space (e.g., each of the two partitions used by TM are sized at three times the hard drive space of each laptop, etc.). Everything works flawlessly.
    (6) Network Attached Storage (NAS) - In addition to using the TC's Network Attached Storage (NAS) capabilities to wirelessly back-up two Apple laptops via TM, I also store other additional files on both (A) the hard drive built into the TC and (B) the additional external hard drive connected to the TC via USB (there are additional separate partitions on this drive for these other additional and non-TM backup files).
    I use the TC's NAS feature with my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Again, everything works wirelessly and flawlessly. (Note: the Apple TV is connected to the network via Ethernet and a LAN port on the back of the TC).
    The issue I am having is when I try to listen to music via Apple's AirPlay in the master bedroom. This master bedroom is located at a distance of two rooms away from the TC's current location in the living room, which is a distance of about 50 feet. This apartment has a long rectangular floor plan where each room is connected to the next in a straight line. In order to use AirPlay in the master bedroom I am using a second extended Wi-Fi base station (a Netgear branded product) to wirelessly extend my WiFi network to a Denon receiver located in the master bedroom and requiring a wired Ethernet connection. This additional base station connects wirelessly to the WiFi network provided by my TC and then gives my Denon receiver the wired Ethernet connection it needs to use AirPlay. I have tried moving my iTunes music directly onto my laptop's hard drive, and then I used AirPlay on this same laptop to connect to the Denon receiver. I always get a successful connection and the song plays, but the problem is that the connection inevitably drops.
    I live in an apartment building and all of the many wireless routers in this building create a great deal of WiFi interference on both the 2.4 GHz and 5GHz bands. I have tried connecting the Netgear product to each the 2.4 and 5 GHz bands, but neither band can successfully maintain a wireless connection between the TC and the Netgear product. I also attempted to maintain a wireless connection to an iPod touch using the 2.4 GHz band and AirPlay on this iPod touch to play music on the Denon receiver. Again, I was able to establish a connection and successfully play music, but after a few minutes the connection dropped and the music stopped playing. I therefore have concluded that I have a poor wireless connection in the master bedroom. I can establish a connection, but it is intermittent with frequent drops. I have verified this with both laptops by working in the master bedroom for an entire day on both laptops. The Internet connection in this master bedroom proved to drop out frequently - about once an hour with the laptops. The wireless connection and the frequency of its dropout are far worse with the iPod touch and an iPhone.
    I cannot relocate the TC. Also, this is an apartment and I therefore cannot extend the range of my network with Ethernet cable (I cannot drill through walls/ceilings, etc.). It is an old building with antiquated wiring and power-line adapters are not likely to function properly, nor can I spare the direct power outlet required with a power-line adapter. I simply need every outlet I can get and cannot afford to block any direct outlet.
    My solution is to use a more powerful wireless router. I found the ASUS RT-AC66U Dual-Band Wireless-AC1750 Gigabit Router which will likely provide a better connection to my wireless Internet in the master bedroom than the TC. The 802.11ac band of this Asus wireless router is totally useless to me, but based on what I have read I believe this router will provide a stronger connection at greater distances then my TC. And I will be ready for 802.11ac when it becomes more widely available.
    However, I still need to maintain the TC's ability to work seamlessly with TM to backup my two laptops. Also, I doubt the new Asus router will provide OS X 10.8.2 with NAS like features and capabilities. Therefore, I still would like to use the TC's NAS capabilities to share files on my network wirelessly assuming the Asus wireless router fails to provide this feature. I need a new and more powerful wireless router, but I need to maintain the TC's NAS features and seamless integration with TM. Finally, I want to continue to use my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also want to continue to use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Can someone advise on how to set-up my existing TC with this new Asus wireless router in such a way to accomplish all of this?
    Modem
    Motorola SB6121 SURFboard DOCSIS 3.0 Cable Modem
    Existing Wireless Router and Primary Wi-Fi Base Station - Apple Time Capsule
    Apple Time Capsule MC343LL/A 1TB Sim DualBand (purchased June 2010, likely the Winter 2009 Model)
    Desired New Wireless Router and Primary Wi-Fi Base Station - Non-Apple Asus
    ASUS RT-AC66U Dual-Band Wireless-AC1750 Gigabit Router
    Extended Wi-Fi Base Station - Provides an Ethernet Connection to a Denon A/V Receiver Two Rooms Away from the Modem
    Netgear Universal Dual Band Wireless Internet Adapter for TV & Blu-Ray (WNCE3001)
    Addition External Hard Drive Attached to the Existing Apple Time Capsule via USB
    WD My Book Studio 4TB Mac External Hard Drive Storage USB 3.0
    Existing Laptops on the Wireless Network Requiring Time Machine Backups
    MacBook Air (11-inch, Mid 2012) OS X 10.8.2
    MacBook Pro (13-inch Mid 2010) OS X 10.8.2
    Other Existing Apple Products (Clients) on the Wireless Network
    iPod Touch (second generation) is model A1288.
    iPad (1st generation)
    Apple TV (3rd generation) - Quantity two (2)

    Thanks Bob Timmons.
    In regards to a Plan B, I hear ya brother. I am already on what feels like Plan Z. Getting WiFi to a far off room in an apartment building crowded with WiFi routers is a major pain.
    I am basing my thoughts on the potential of a new and more powerful router reaching the far off master bedroom based on positive reviews on cnet.com, pcmag.com and pcworld.com. All 3 of these web sites have reviewed the Asus RT-AC66U 802.11AC wireless router as well as its virtual twin cousin 802.11n router. What impressed me is that all 3 sites rated this router #1 overall in terms of both range and speed (in both the 802.11n and 802.11AC flavors). They tested the router in real world scenarios where the router needed to compete with a lot of other wireless routers. One of the sites even buried this Asus router in a media room with thick walls and inside a media cabinet. This Asus router should be able to serve my 2.4 GHz band wireless clients (iPod Touch and iPhone 4) with a 2.4GHz Wireless-N band offering some 50 feet of dependable range and a 60 Mbps throughput at that range. I am hoping that works, but it's borderline for my master bedroom. My 5 GHz wireless clients (laptops) will enjoy a 5GHz Wireless-N band offering 150 feet of range and a 200 Mbps throughput at that range. I have no idea what most of that stuff means, but I did also read that Asus could reach 300 feet and I got really excited. My mileage may vary of course and I'm sure I'm making some mistakes in my interpretation of their data. However, my Winter 2009 Time Capsule was rated by cnet.com to deliver real world performance of less than that, and 802.11AC may or may not be useful to me someday. But when this Asus arrives and provides anything other than an excellent and consistent wireless signal without drops in the master bedroom it's going right back!
    Your solution sounds great, but I have some questions. I'm using OS X 10.8.2 and Airport Utility (version 6.1 610.31) and on its third tab labeled "Wireless" the top option enables you to set "Network Mode" to either:
    Create a wireless network
    Extend a wireless network
    Off
    Given your advice to "Turn off the wireless on the TC," should I set Network Mode to Off? Sorry, I'm clueless in regards to how to turn off the wireless on the TC any other way. Can you provide specific steps on how to turn off the wireless on the TC? If what I wrote is correct then what should the rest of this Wireless tab look like, or perhaps it is irrelevant when wireless is off?
    Next, what do you mean by "Configure the TC in Bridge Mode?" Under Airports Utility's fourth tab labeled "Network" the top option "Router Mode" allows for either:
    DHCP and Nat
    DHCP Only
    Off (Bridge Mode)
    Is your advice to Configure the TC in Bridge Mode as simple as setting Router Mode to Off (Bridge Mode)? If yes, then what should the rest of this "Network" tab look like? Anything else involved in configuring the TC in Bridge Mode or is it really as simple as setting the Router Mode to "Off (Bridge Mode)"?
    How about the other tabs in Airport Utility, can they all stay as is assuming I use the same network name and password for the new Asus wireless router? Or do I need to make any other changes to the TC via Airport Utility?
    Finally, in regards to your Plan B suggestion. I agree. But do you have a Plan B for me? I would greatly appreciate any alternative you could provide. Specifically, if you needed a TC's Internet connection to reach a far off corner of your home how would you do it? In the master bedroom I need both a wired Ethernet connection for the Denon a/v receiver and wireless Internet connection for the iPhone and iPod Touch.
    Power-Line Adapters - High Cost, Blocks at Least One Wall Outlet and Does Not Solve the Wireless Need
    I actually like exactly one power-line adapter, which is the D-Link DHP-540 PowerLine AV 500 4-Port Gigabit Switch. This D-Link power-line adapter plugs into your wall outlet with a normal sized plug (regular standard power cord much like any other electronic device) instead of all of the other recommended power-line adapters that not only use at least one wall outlet but also often block the second outlet. You cannot use a power strip with a power-line adapter which is very impractical for me. And everything about my home is strange and upside down. The wiring here is a disaster and I don't have faith in its ability to carry Internet access from the living room to the master bedroom. And this D-Link power-line adapter costs $90 each and I need at least two to make the connection to the Denon A/V receiver. So, $180 on this solution and I still don't have a dependable drop free wireless connection in the master bedroom. The Denon might get its Ethernet Internet connection from the power-line adapter, but if I want to use an iPhone 4 or iPod Touch to stream AirPlay music to the Denon wirelessly (Pandora/iTunes, etc.) from the master bedroom the wireless connection will not be stable in there and I've already spent $190 on just the two power-line adapters needed.
    Extenders / Repeaters / Wirelessly Extending the Wireless Network
    I have also read great things about the Amped Wireless High Power Wireless-N 600mW Gigabit Dual Band Range Extender (Repeater) SR20000G and the My Net Wi-Fi Range Extender. The former is very powerful and the latter is easier to install. Both cost about $150 ish so similar to a new Asus router. However, everything I read about Range Extenders points to them not being very effective for a far off corner of your house wherein it's apparently hard to place the range extender in the sweet spot where it both gets a strong enough signal to actually effectively extend the wireless signal and otherwise does not reduce network throughput speeds to unacceptable speeds.
    Creating a Roaming Network By Hard Wiring with Ethernet Cable - Wife Would Say, "**** No!"
    Even Apple seems to warn against wirelessly extending your network (see: http://support.apple.com/kb/HT4145#) and otherwise strongly recommends a roaming network where Ethernet cable is used to connect two wireless base stations. However, I am in an apartment where stringing together two wireless base stations with Ethernet cable would have an extremely low wife acceptance factor (WAF). I cannot (both contractually and from a skill prospective) hide Ethernet wire in the walls or ceiling. And having visible Ethernet cable running from room-to-room would be unacceptable, especially to the wife.
    So what is left? Do you have a Plan B for me? Thanks in advance for your help!

  • Time Capsule set up and wifi network OK but MacBook doesn't see capsule as airport device.  Do I need to do a hard reset and start again?

    I recently bought a Time Capsule and sucessfully set it up in accordance with the instruction book.  The home network and guest network seem to work fine but my MacBook cannot find the Time Capsule wirelessley.
    Initially I set up the time capsule connected to the MacBook with an ethernet cable.  The Time Machine got 30GB way through a 60GB initial back up and then stopped for no obvious reason.  Since then the capsule has not been visible to the MacBook.  I have tried to reconfigure through Airport Utility but even after reperated rescans the capsule remains invisible.
    Any help would be extremely welcome.

    1. i would restore the express to factory defaut by holding the reset button on the unit with a paperclip while you are powering it on
    2. if it restored, you should be able to see it in your wifi icon at top of screen as "airport express"
    or you can see it in airport utility
    3. then if you want to connect it wirelessly to your time capsule, you would choose "extend network" and put in relevant security and password....this would make the express a wireless access point, fed by your time capsule(main router)
    if you chose to do it wired which is a better way if you have access to ethernet port at wall, you would choose "create a wireless network" and then under the "network" tab you would choose "Bridge Mode".....this would make the express a wired access point, fed by your time capsule(main router)

  • Time Capsule Won't Allow Some Programs to Open

    I have a 1TB TC with less than 25GB in one sparse bundle on it. Free space is +/- 930GB. My system is as follows:
    eMac 1.25Ghz, 500GB internal drive, 2GB memory, OS X 10.4.11, all updates are current.
    3TB of storage connected to the eMac via Firewire 400 for additional storage (video).
    1TB Time Capsule connected to the eMac via 1000GB Ethernet.
    I had to reformat two of the Video (Firewire) drives and transfered 900GB to the TC. This upload by the way takes greater than 10 times longer than to Firewire disks.
    I reformatted the FW disks.
    When I went to do download the files from TC to the video FW disks I started multiple copy processes. As i write this I have 4 going on, 1-152GB, 1-75GB, 1-525GB and 1-69GB.
    The problem is that several programs such as Activity Monitor, Empty Trash (on disks not being used for the copy), Preview and Acrobat Professional "hang" or fail to open while the copy is in progress. Now normally I'd wait, however some things such as activity monitor and empty trash I need to use. Since the process takes several days this is not great!
    Other programs such as Safari and Mail work fine!
    Any ideas?
    John Schubert

    Yeah, I had 8 or 10 copy (transfers) going at once, now I'm down to 4. I do this all the time, however before now I've always used Firewire. Does Ethernet require more processor overhead? It would seem so.
    I've been looking at a new Xserve or possibly a recent used Xserve and a rack; this video stuff really eats up hard drives. Saw a rack mount enclosure that holds 12 IDE drives-9TB possible for $749 and has Firewire connectivity. I could put all my existing drives in that and have everything in one place.
    Anyway I've go to live with what I've go for now.
    Thanks
    John Schubert

  • How do I use the time capsule to share itunes music between multiple apple devices? Also, is it possible to control the music on one device using another, and how do you set this up?

    How do I use the time capsule to share itunes music between multiple apple devices? Also, is it possible to control the music on one device using another, and how do you set this up?

    unless i'm missing something, i think you got mixed up, this is easy google for walk throughs
    i'm assuming this is the new 3tb tc AC or 'tower' shape, if so, its wifi will run circles around your at&t device
    unplug the at&t box for a minute and plug it back in
    factory reset your tc - unplug it, hold down reset and keep holding while you plug it back in - only release reset when amber light flashes in 10-20s
    connect the tc to your at&t box via eth in the wan port, wait 1 minute, open airport utility look in 'other wifi devices' to setup the tc
    create a new wifi network (give it a different name than your at&t one) and put the tc in bridge mode (it may do this automatically for you, but you should double check) under the 'network' tab
    login to your at&t router and disable wifi on it
    add new clients to the new wifi network, and point your Macs to the time machine for backups

  • How can two computers use time machine on same Time Capsule?

    I just purchased a Time Capsule and successfully backed up my computer. My brother is on the same network but cannot get Time Machine to back him up on the Time Capsule without my backup being deleted.
    How does one enable Time Capsule to serve as back up for two different computers?

    There are some options:
    Manually delete a number of old backups from the Mac that's "hogging" the space, per #12 in  Time Machine - Frequently Asked Questions.  After "compacting" that sparse bundle per the pink box there, you may be able to limit the maximum size of it, per #A8 in Time Machine - Troubleshooting.
    Another is to connect a USB drive to the TC (likely with a powered USB hub), and back the other Mac up to it, instead of the TC's internal HD.

Maybe you are looking for