15" i7 Macbook Pro from early 2011.takes the mac laptop two or three tries to boot successfully. It would turn on, show gray screen, shut down, turn on again, show gray screen, shutdown, and then turn on, show gray screen, before it can finally get

Hello All,
I have a 15" i7 Macbook Pro from early 2011. The past few weeks, it has been getting increasingly difficult to get on my computer. It takes the mac laptop two or three tries to boot successfully. It would turn on, show gray screen, shut down, turn on again, show gray screen, shutdown, and then turn on, show gray screen, before it can finally get to the dark gray log-in screen. Even when I finally get logged in to start working, thinking it would be okay now, it shuts down randomly.
I've ruled out the possibility of a software problem because I've just done a clean re-install of Mac OS X Mavericks on my computer just yesterday.
I did upgrade the RAM recently, about a month and a half ago, from 4GB to 16GB, I went to the apple store four days after that upgrade to have them do a hardware test, and clean the inside of my laptop, which helped with previous heat issues. When they did the hardware test, the hardware was all registered as fine from their system.
I've tried resetting the SMC, PRAM, and doing the internet recovery hardware test, but to no avail. I thought I could at least find out what parts needed to be replaced from the hardware test but it seems that when the hardware test is almost finished, the computer just shuts down, So I am unable to see the results.
My computer is also having battery issues, under battery condition, it says "replace now," parts have been ordered, waiting for arrival. But if the battery health is low, it should still boot up fine, it would just hold a significantly less charge.
Could this be a hard drive issue?
Has anyone had similar symptoms and how was it resolved?
Does anyone know what I can do to alleviate this issue?
I haven't had time to take it to Apple because I'm currently taking a 21 credit semester academically. I'm an art and design student so my computer is basically the bane of my existence. Help! Any constructive advice is welcomed!
Thank you so much for your input!
-Christina C.

Problem description:
The Hard Disk is failing.
EtreCheck version: 2.0.11 (98)
Report generated November 4, 2014 at 7:59:28 AM EST
Hardware Information: ℹ️
MacBook Pro (15-inch, Early 2011) (Verified)
MacBook Pro - model: MacBookPro8,2
1 2.2 GHz Intel Core i7 CPU: 4-core
16 GB RAM Upgradeable
BANK 0/DIMM0
8 GB DDR3 1600 MHz ok
BANK 1/DIMM0
8 GB DDR3 1600 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
Intel HD Graphics 3000 - VRAM: 512 MB
Color LCD 1440 x 900
AMD Radeon HD 6750M - VRAM: 1024 MB
System Software: ℹ️
OS X 10.9.5 (13F34) - Uptime: 0:3:43
Disk Information: ℹ️
TOSHIBA MK7559GSXF disk0 : (750.16 GB)
S.M.A.R.T. Status: Verified
EFI (disk0s1) <not mounted> : 210 MB
HDV4 (disk0s2) / [Startup]: 749.30 GB (712.10 GB free)
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
MATSHITADVD-R   UJ-898
USB Information: ℹ️
Apple Inc. FaceTime HD Camera (Built-in)
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Computer, Inc. IR Receiver
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/Library/Application Support/Avast/components/fileshield/unsigned
[loaded] com.avast.AvastFileShield (2.1.0 - SDK 10.9) Support
/Library/Application Support/Avast/components/proxy/unsigned
[loaded] com.avast.PacketForwarder (1.4 - SDK 10.9) Support
Launch Agents: ℹ️
[not loaded] com.adobe.AAM.Updater-1.0.plist Support
[loaded] com.avast.userinit.plist Support
Launch Daemons: ℹ️
[invalid?] com.adobe.SwitchBoard.plist Support
[loaded] com.avast.init.plist Support
[loaded] com.avast.uninstall.plist Support
[loaded] com.avast.update.plist Support
[invalid?] com.perion.searchprotectd.plist Support
User Launch Agents: ℹ️
[invalid?] com.avast.home.userinit.plist Support
[loaded] com.google.keystone.agent.plist Support
[invalid?] com.jdibackup.ZipCloud.autostart.plist Support
User Login Items: ℹ️
None
Internet Plug-ins: ℹ️
AdobePDFViewer: Version: 10.1.1 Support
QuickTime Plugin: Version: 7.7.3
JavaAppletPlugin: Version: 14.9.0 - SDK 10.7 Check version
Default Browser: Version: 537 - SDK 10.9
User Internet Plug-ins: ℹ️
TroviNPAPIPlugin: Version: 1.0 - SDK 10.9 Support
Google Earth Web Plug-in: Version: Unknown
Safari Extensions: ℹ️
Avast Online Security
Trovi Search for Safari
3rd Party Preference Panes: ℹ️
None
Time Machine: ℹ️
Time Machine not configured!
Top Processes by CPU: ℹ️
      16% mds
      7% WindowServer
      1% loginwindow
      1% fontd
      1% com.avast.daemon
Top Processes by Memory: ℹ️
120 MB com.avast.daemon
86 MB Google Chrome
52 MB Finder
52 MB WindowServer
41 MB Google Chrome Helper
Virtual Memory Information: ℹ️
13.45 GB Free RAM
1.34 GB Active RAM
944 MB Inactive RAM
1.43 GB Wired RAM
1.11 GB Page-ins
0 B Page-outs

Similar Messages

HT201343 I have an Early 2011 MacBook Pro from Early 2011 that is a 13-inch model... why won't it support airplay? why can't I get a software update to allow it to work?

I have an Early 2011 MacBook Pro from Early 2011 that is a 13-inch model... why won't it support airplay? why can't I get a software update to allow it to work?

About AirPlay and Airplay Mirroring
AirPlay Mirroring requires a second-generation Apple TV or later, and is supported on the following Mac models: iMac (Mid 2011 or newer), Mac mini (Mid 2011 or newer), MacBook Air (Mid 2011 or newer), and MacBook Pro (Early 2011 or newer). For non-qualifying Macs you can try using Air Parrot.
Several Apple Articles Regarding AirPlay
Apple TV (2nd and 3rd gen)- How to use AirPlay Mirroring
How to set up and configure AirPort Express for AirPlay and iTunes
About AirPlay Mirroring in OS X Mountain Lion
iTunes 10- About playing music with AirPlay
Troubleshooting AirPlay and AirPlay Mirroring
Using AirPlay
Thanks to the $15 Beamer, AirPlay streaming is still possible on Macs that do not support Airplay and mirroring.
Another solution is the Air Parrot.

SSD-problem with MacBook Pro 13" (Early 2011)

Hi there,
I've tried to use two different SSDs in my MacBook Pro 13" (early 2011). The first one (Samsung 840 Series, 500GB) crashed after two days: the beachball appeared and after a restart there was this question mark-symbol on my screen: no system found. Had to send this SSD back to Amazon. A few days later I've bought a new one, a SanDisk Extreme with 450GB. I've used it for two days, then my system crashed again and after a restart of my Mac I couldn't get any further than to the grey apple-symbol. Even the recovery partition didn't work anymore. Does anyone of you have the same problem with his (or her) MacBook Pro 13" (early 2011) - and any ideas for a solution?
Thanks for your answers!
Torsten

can you confirm if this is ok to buy:
http://www.ebay.ca/itm/New-HDD-Hard-Drvie-Cable-for-13-MacBook-Pro-A1278-MD101-M D102-821-1480-A-2012-/181269577616?pt=LH_DefaultDomain_0&hash=item2a34823f90&_u h b=1
or
http://www.ebay.ca/itm/NEW-MacBook-Pro-Unibody-13-A1278-2012-md101-102-HDD-Hard- Drvie-Cable-821-1480-A-/121183868039?pt=LH_DefaultDomain_0&hash=item1c371f1487& _ uhb=1
or this one..??
http://www.ebay.ca/itm/for-APPLE-MacBook-Pro-13-A1278-HDD-Hard-Drvie-Cable-MD101 -MD102-821-1480-A-2012-/331060187298?pt=LH_DefaultDomain_0&hash=item4d14b990a2& _ uhb=1
i guess i aint gotta buy those brackets again..?
Thanks
Anjillan

I have the new macbook pro from late 2011. when i try plugging my cannon gl2 into the mac via firewire 800 it does not show up in iMovie as an option to import from. i even have gone into my settings on the camera and changed it to vcr.

I have the new MacBook Pro from late 2011. "the one before the new ritina display" i have a cannon gl2 video camera which is mini dv. when i plug it into my mac via firwire 800 it does not show up in the iMovie. i have set the settings on the camera to vcr mode and changed it to av->dv out. when i click on the import from camera on imovie it doesnt even show my camera in it. it just gives me the option to import video from my facetime camera. the camera is turned on the wires are connected i know for fact that its a firewire and not a usb. i know what they each look like. i bought the firewire cable and it was marked down cause it was an opened and used item. would it be possible that it could be deffected and if that is not the reason what other options do i have?

I would say that odds are high that you have a bad cable. Maybe that is why they returned it.
I would suggest trying a different firewire cable.
You can find Firewire cables inexpensively at monoprice.com. You need a 4 pin to 9 pin firewire cable.
Here is a link.
http://www.monoprice.com/products/subdepartment.asp?c_id=102&cp_id=10301
Other things to check:
Is your camera plugged in to wall power (not to batteries only). Must be hooked to an AC power source to import.

MacBook Pro 17" Early 2011 Model: Auto Shutdown/Restart Problem

Hey guys!
This is my first time to sign in, join the community, and ask a question or create a discussion. FYI, I really have little knowledge on tech stuff so please bear with me. Here's my problem, and I hope you can give out your suggestions:
I have a MacBook Pro 17" Early 2011 Model which I have upgraded to OS X Mountain Lion.
A month or two ago, it had started shutting down or restarting at random times. As time passed, this problem became more frequent.
I finally decided to have it checked at Digital Hub, a licensed Apple distributor. After almost a week, they've finally diagnosed that the problem is with my battery. I got my MacBook pro back around 2 (two) weeks ago, and ever since then I had to use an outlet in order for it and myself to work properly. Right now, I'm still saving up to purchase new batteries.
Recently, however, I've noticed that my MacBook Pro auto restarts even when plugged. Take note, RESTART and no longer shutting down completely. Upon further trials, I've finally concluded that it does so only during the use of heavy programs such as Diablo 3, Final Cut Pro X, and when rendering with iMovie. I have yet to try with Adobe products, particularly with Lightroom and Photoshop, and see if it does the same. But more or less, that's what I've noticed so far.
Given that I still haven't purchased the battery yet, I know it's still vague to know the real probelm/solution. But with the given situations, what are you views on this matter? Please let me know. It'd be of great help. Thank you and I hope to hear from you soon!
Brent Hughldridge A. Chua
Multimedia Arts Student
Philippines
(Note, I'm a starting out Multimedia Arts Student and photographer. I have little knowledge of the industry for now, but I'm willing to learn. So please forgive me if I don't understand your suggestions at once if they are very in depth or technical.)

Thanks for taking so much time in helping me.
Just an update:
2 loops/passes done - no errors.
Called up Digital Hub and talked to the technician, he says there are 3 possible problems:
1. Battery (which is still inside the laptop) may cause some disturbances with the electric current
2. Software related - most likely re-formatting may be needed
3. Video card may have failed, which means complete change of the logic board ----> worst case
I'm crossing my fingers that it's either of the first two.

Help MacBook Pro 13" early 2011 suddenly black screen in Windows 7 SP1. EFI 2.2.

Hi, everyone, I need help here.
Apple MacBook Pro 13" early 2011 preinstall Lion version, EFI 2.2, Boot Camp 4.0. suddenly black screen in Windows 7 SP1 (black screen and also no sound at all, need to press power button to off). What happen?? Please someone tell me what to do?
I have delete bootcamp HD and reinstall windows 7 but the problem is still here, I have reset PRAM and SMC too.
The video on the black screen: (http://www.youtube.com/watch?v=z3dLTFSD-v8)

Oh I actually have the problem in Mac OS, not even using the Bootcamp or Windows 7
Csound1 wrote:
lokiman wrote:
I am having the exact same problem with my 13" early 2011 Macbook Pro. I have 10.6.8. I used the disk that came with the laptop to restore the OS to 10.6.7 but the problem existed there too. I have now updated it back to 10.6.8. The problem still exists. This doesn't seem to be limited to an OS version and seems like an issue with device driver or with hardware. I will try to take it to the Apple store and see if this gets resolved.
You too have a black screen in Windows 7. ?

My Macbook Pro (15" early 2011) got blue screen every i normally booted it. It only can enter the OS when it's in safe boot. Solution please.

My Macbook Pro (15" early 2011, Mountain Lion, but after reinstall i change it to snow leo) got blue screen every i normally booted it. It enter the OS only when it's in safe boot.
I've tried any solution that i got from the internet, such as:
-Reinstalling the OS X (normal install & clean install)
-Reset PRAM and SMC
-Repair Disk Permissions and Repair Disk from Disk Utility (the result is OK. There's no problem)
-Repair Disk Permissions manually (with Command + S at the beginning of booting)
-Checking Hardware from Application Installer DVD (result is OK)
-Checking from Mac Resource Inspector/MRI (result OK)
-Booting from Recovery Disk is same problem, blue screen
All of that solution is not working. My Macbook still got light blue screen and sometimes blue screen with lines after apple logo and spinning wheel is shown.
HDD is in good condition because when it's checked on the other macbook it can be booted. But if you must know, other HDD can't be booted when its plugged to my macbook (blue screen again). If i do safe booting, it works but can't play video and music also photobooth. I got confused with this case.
Any solution or comment? Thank you very much by the way

Hi. I'm not trying to rush things, you may have a different problem, but your issue looks quite familiar to me. I recently had a problem with the discrete graphics card (the Radeon GPU) due to overheating, all because a faulty application of the thermal compound in the factory.
In my case, the problem started slowly and intermittently, a few days after a gaming session (Quake 3) of about three hours (at the moment, I didn't realized that could be linked to the problem).
This issue is being actively discussed in another threads in this forum, but so far there's enough evidence that it's been causing similar problems for 2011 MBPs owners: screen corruption, black/blue screens, and in some cases, a total inability to boot. Some of the threads I'm talking about:
https://discussions.apple.com/message/13150366#13150366
https://discussions.apple.com/message/21110132#21110132
So far, and since the problem seems to affect only the discrete GPU (that's why you can boot in safe mode) a possible solution is to disable it by removing some extensions which prevent OS X from loading the Radeon drivers. This post describing the process (there are different files involved depending of your GPU version, so make sure you are moving the right ones):
https://discussions.apple.com/message/22521574#22521574
In the case your discrete GPU survived and is not permanently damaged, I personally had success by changing the thermal compound myself, which completely fixed the problem (at least for now). I've posted about it here:
https://discussions.apple.com/message/22630561#22630561
I hope you can find a solution, believe me I know the feeling when you see your expensive machine turning into a brick and it *****.
Good luck!

I got my Macbook Pro 17inch (early 2011) back from Apple (they had to replace the logic board) and now my microphone is not working

I got my Macbook Pro 17inch (early 2011) back from Apple (they had to replace the logic board) 3 days ago, I had a terrible experience as the genious who gave me my solid state disk for safekeeping lost my disk's brackets thus I had to wait 2 more hours until they find one after 10 days of waiting for the repair. I noticed some weird sounds, like somehting is moving with the mac 1-2 times, even if I have no mechanical parts other than the fans, but my real issue at the moment is that my microphone is not working. I can see the mic in the System Info however and in Audio Midi Setup. In the Audio Midi Setup I see that the master chanel is turned off and I can't turn in on. Ch 1 and 2 are on full. I also noticed the first seconds after the comp. boots the blue bar goes to the middle in the System Preferences -> Sound -> Input. Any ideas what to do or try? I do not want to go back to the apple store as it is 50 minutes away from here and I need my laptop as a computer science student. Everything else is working perfectly.

You need to call both the store that did the repair and Apple directly, warranty service or Apple care, and report this problem with both of them and get a ticket number of some kind (some kind of verification number) that the unit just came back from major service with this problem and that you want it fixed when you can lose the use of it, which is not right now.
Without doing something like that they could easily say it is damage not covered under the normal warranty.
God knows what the repair center did and did not do to it while it was there.
And depending on when you actually bought it the warranty could run out in the mean time.

Can I upgrade my RAM from 4GB to 8GB for my MacBook Pro 13(early 2011 2.7GHz)? And how much would it be?

Can I upgrade my RAM from 4GB to 8GB for my MacBook Pro 13(early 2011 2.7GHz)? And how much would it be?

you can upgrade to 16GB if you wish to do so...
average price for 8GB 1333MHz DDR3 is around $50 - $75 depending on the brand.
why not spend $100 and go with 16GB 1333MHz from Crucial or Corsair.
you can get them from Amazon.com or newegg.com
see image below with 16GB Patriot Mac Series 1333MHz for $100.

I am looking at a MacBook pro 17 early 2011 with water damage that doesn't turn on. Now t would have a voided warranty wondered if anyone knew how much apple would charge to fix. If its worth fixing?

I am looking at a MacBook pro 17 early 2011 with water damage that doesn't turn on. Now t would have a voided warranty wondered if anyone knew how much apple would charge to fix. If its worth fixing?

It mostly depends on the damage that was done (the LCD, keyboard, etc) but yours does not turn on so I am assuming it was fully submerged and completely damaged. Therefore, I would think your warranty is most definitely void.
When did this happen? How bad was it? Have you taken any measures to get it to dry? You can go online and you can find tips on how to dry it at least a bit so that it is not as bad, it might not get it to work, but it can help you prevent rusting, which would cause further damage thus reducing the probability of getting repaired/replaced. Also, do not try to turn it on unless you have tried to dry it as it will damage it even more (electricity + water = destruction). I would suggest giving this a try, and if it is still not working then it is probably worth a try with Apple, just go in for a consultation in terms of pricing. If they seem too high and/or the warranty is void, then you can opt for after-market products which significantly reduce the repair costs... as you would have nothing to lose anyway in terms of warranty.
It's $3,000, that pays my rent. Even investing $1,000 would be better than just not giving it a try at all lol.

Does my macbook pro 13" early 2011 will be compatible with 2560x1440 thunderbolt screen resolution?

I'm planning to buy a Thunderbolt display for my macbook pro 13" early 2011,
I want to know if after connect the laptop to the screen, will show in 2560x1440 resolution
Thanks for your help!

Specs say:
External Resolution
Up to 2560 by 1600 pixels

Macbook Pro 13" Early 2011 Lag Spikes

Okay let me just brief you on my Macbook.
In September 2011 i bought a Macbook Pro 13" Early 2011 model, 4GB RAM, 2.7GHz Processor, you can get the rest on the site.
( http://support.apple.com/kb/sp619 )
I bought it as a ex-display model, so you can imagine it already has some milage from it.
Through the (almost) 2 years i've had it, apart from the odd overheat shutdown, and a 1 charger replacement, it's been no hassle, even with me constantly shutting it and moving it. It seems that all the issues are coming in bulk.
I generally use the laptop for gaming, mostly World of Warcraft, sometimes Minecraft, and lately Starcraft, and Spellforce on BOOTCAMP or virtual machines.
About 2 weeks ago, the laptop started refusing to charge, i couldn't understand if it was the charger (as i only replaced it a few months earlier and the cable was still in perfect condition) or the port itself in the laptop. I took my laptop to an Apple store, found it was the Magsafe on the cable, replaced it on the spot, but the reason why i'm saying this is i'm wondering why it broke so quickly, and if lack of power has anything to do with it.
I've grown a liking to Spellforce so instead of having to restart into the Windows side of my Mac, i just use the Virtualbox Virtual OS i already have set up from when i used to work from home and have to use certain software on windows because Wine just couldn't cut it (and lets face it, Mission Control is awesome, then you go on Windows and everything just seems to cluttered). So i read the default specs for the game on Steam (2GB) so i give Virtualbox 2GB, but this was a MAHOOSIVE mistake, because as soon as i clicked start, it's been a down hill spiral.
The computer immediately started lagging, to the point where the laptop was actually unusable, so i force restarted it by pressing down the power button for 5 seconds and i let it restart. After it booted, everything seemed fine (i expected nothing else) so i decided to only give it 1GB of RAM, and just turn down the settings to the lowest possible (which is something i've had to do with World of Warcraft recently. It used to be able to run on Ultra when i first got the laptop, now it struggles on low and if i have a browser up at the same time). Again, big mistake, it lagged to unusability. So i restart again, but this time it takes 5 minutes to boot, and once booted everything is so slow, so i decide to re-install the OS, so i get my flash drive and spend the next hour moving things over from my user folder because when i would try to move a folder that had 5+ files or something that was 100MB or larger, it would error out saying a certain file couldn't be read or written, and would cancel and remove everything else that was transfering at the time.
So i restart but boot into the recovery option, and do a refresh the OS, and i let it download and install. I was surprised to see when it had all completed that it still had all my files, but it still ran slow, not as slow as before but definitely not as good as before, i would estimate at quatre the performance. So i assume that Virtualbox must have editted some system setting and my Mac thinks i only have 2GBs of RAM and not 4GB, so i search on how to reset the bootloader, and i was tried the alt + cmd + r + p, but after that when it booted, it came to the wallpaper but i was getting these popups that Finder had unexpectedly quit, so i click Okay a few times, they keep coming back up, so i look at the details and it says that the app had failed 500+ times before.
So i put my Snow Leopard disk in, use Disk Utility and use erase on my Mac OS partition, then i re-install Snow Leopard, then i download and install Mountain Lion again, but the snails pace remains. I do alittle more research and someone suggested modifying the partition size by a few gigs or so to re-write it and reset certain variables attached, didn't work, even after a reboot.
So yesterday i just put the Snow Leopard disk in, and i remove both partitons (Mac and Windows) and i make one partition. I install Snow Leopard and then Moutain Lion, and so far it appears that everything it back up to speed... however, i've been keeping a keen eye on Activity Moniter and "top" in Terminal, and my CPU usage and RAM usage are always relatively low. I always seem to have 1GB-2GB RAM free, and my Idle CPU always seems to be above 80%-90% but i'm getting these weird lag spikes. I notice it most when i try installing World of Warcraft again, the download speed averages around 3MB/s (my ISP is Virigin Media and i get 60Mbs/s fibre optic so i know it's not my connection failing) and then the app seems to freeze (stops refreshing the average speed, and then about 5-10 seconds later, it starts refreshing again but it's at 12-50KB/s. This also seems to happen a lot when i use web browsers.
I have noticed something new, literally only about 30 minutes before i started writing this. There is a noise that happens every 2-4 seconds, it's pretty regular, it sounds like a grasshopper, or other chirping bug/insect inside my laptop. It sounds like metal scraping against metal, which is worrying. It's coming from the right hand side of the Magic Track Pad, which is where i believe the Hard Drive is. I've looked online and this seems to be a sign that the harddrive is dying.

Yeah, the problem has been solved.
Unfortunately, the solution is buying a new storage device.
So if you're having these issues, i tried almost everything consumer possible, that's free anyway, and the hard drive was just too faulty to work properly. So backup all your stuff whilst you still can.
I bought an SSD for around £80, only 120 gigs of storage, but i have iTunes Match so i don't need to have my films and music downloaded.
If you're very mobile with your laptop, then i suggest getting an SSD. Lugging about a laptop with a storage device with moving parts is very very risky.
As soon as i got a new storage device, everything was back to normal. It was like it was new again.
Anyway, sorry i can't give you a free solution, but it's the only solution i got.

When i connect my philips 170c monitor to my macbook pro 13" early 2011, it does not detect the second monitor?

help! i've googled around, but none seems to solve my problem
my macbook pro is early 2011, 13", running lion.
the philips monitor is vga only, so i have a mini display port to vga adaptor and connecting it to the vga.
the screen on my mbp does turn blue, but no input is detected on the external monitor.
any advice?

If it does not detect the display automatically, try going to system preferences>displays, click detect displays.

My MacBook Pro 13'' Early 2011 is not booting.

Hello,
I have a Macbook Pro 13'' Early 2011. Last week I tried to replace the thermal paste on the processor and on the graphics chip. I followed a video tutorial and an iFixit tutorial step by step during the entire process. Once I was finished I decided to turn on my Macbook and give it a spin. Unfortunately it didn't work, although I haven't touched or damaged anything on the logic board, as far as I'm concerned.
The scenario goes as follows:
I press the start button..
The fan spins once, the hard drive reads for a second and the sleep button flashes for a moment. I am not hearing any chime, neither does my screen go on.
The Macbook Pro turns off again automatically.
I am going to open it once more before it give it to the authorized Apple service. Do you have any idea where the issue might come from?
Thanks for your replies!

If this started happening without your having made any changes and without a warning of low disk space, then it's likely that the startup drive, or some other hardware component, is failing. Back up all data immediately, then make a "Genius" appointment at an Apple Store to have the machine tested.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.

Which SATA has macbook pro 13 early 2011

Hello,
I have a Macbook Pro 13 early 2011, 2 months ago I take out DVD-rom and put in new 128GB SSD, which has 550mb/s read and 520mb/s write speed, but when I do a speed test (Blackmagic disk speed test), it shows that read speed is maximum 150mb/s and write speed maximum 120mb/s, so where is the mistake? Has my Macbook SATA3? Thank you for answers.

MMerevous,
all MacBook Pros from 2011 on support SATA III, but only for the internal disk (or the primary disk, for setups such as yours, where the SuperDrive has been replaced with another internal disk). You will not get SATA III speeds from any disk installed where the SuperDrive used to be, and SATA III hard disks are known to have problems when installed there. For maximizing your throughput, you should put your SSD in the internal disk’s position, and put your hard disk (if it’s not SATA III) in the SuperDrive’s position.

15" i7 Macbook Pro from early 2011.takes the mac laptop two or three tries to boot successfully. It would turn on, show gray screen, shut down, turn on again, show gray screen, shutdown, and then turn on, show gray screen, before it can finally get

Similar Messages

Maybe you are looking for