2014 Mac Mini connected to Samsung s22b310b monitor colors bad upon waking from sleep.

Occasionally when I wake the 2014 Mac mini from sleep the colors on the monitor are very bright. I go into systems preferences and then display. I click on the color button and it will change back to normal. I have tried both a DVI to mini displayport and VGA to mini displayport. Problem occurs with both. What else can I try to prevent this from happening?

Try resetting the SMC and PRAM
Intel-based Macs: Resetting the System Management Controller (SMC)
About NVRAM and PRAM

Similar Messages

2014 Mac Mini won't detect Dell monitor on startup

On a cold start or waking from sleep it is necessary to reset the PRAM in order for the Mini to recognize a Dell P2014H. Restarts are not a problem.
This was not an issue with an older MacBook Pro or an Air at the Genius Bar. I have resolved this by setting preferences to never turn the display off but don't consider this a permanent fix.
I'm running 10.10.1 and connected via VGA to a Thunderbolt port. The monitor is only 7 months old so I'm not inclined to replace it yet or add even more cables to my collection just to find that doesn't fix anything. In fact when another 2014 Mini was connected to my monitor at the Apple store it had the same problem.
On the other hand our 2012 Mini has never had issues with a Dell U2412M. So what's up Apple?

I just bought a Mac Mini with latest operating system 10.10.1 and had the same problem. I also used a monitor with HDMI cable. I spent 45 minutes on the phone with Apple Care tech but no solutions. I took it back to shop and they tested it but did not have a HDMI cable and used a thunderbolt adapter. It worked fine. Bought a Thunderbolt adapter for HDMI cable and problem solved. Both mouse and keyboard now wake up system. Perhaps a future update will solve this but for now I'm happy.
Cam

External monitor initially flashes on waking from sleep

I recently upgraded to 10.4.8. My PowerBook is connected to an external monitor and now often flashes when I wake the machine from sleep. It takes a while too settle down but then works fine. If I wake from sleep without the external monitor, there are no problems. I had no problems using 10.1. Does anyone have a fix?
G4 PowerBook (PowerBook6,1) Mac OS X (10.4.8) 867 MHz

I found the following article from Apple: TA20612. It reads as follows:
"The popping sound does not indicate any software issue or hardware failure. This is a normal part of hardware-software initialization after waking from sleep or during startup."
I'm a bit skeptical. I think I would have noticed this on the old iMac. Since I haven't yet sold it, I'm going to try to arrange for some side-by-side testing. I'll update this thread when I have the results.

'09 mac mini connection to Samsung LCD

I just purchased the new mac mini and am trying to hook it up to my 42" Samsung LCD using the mini display port and a VGA cable. The TV is not recognizing the hookup (PC is not an option in my list of sources). If anyone has any ideas or suggestions on things to try I'd appreciate it! I purchased my TV a little less than three years ago. It's an HD set - model LN-S4092D - in case that helps! Thanks!

tbrodi,
I do have the same stuff. only a newer version of the Samsung and an older mini.
I use a DVIHDMI cable, connect the cable into port 2 on the tv and the audio jack from the mini straight to the input on the tv, the audio out from the tv is going to the recever/amplifier.
At least, that works for me all in full HD
rgrds
McChiel

DVI monitor fuzzy sometimes when waking from sleep

Hi there,
I have a new Samsung SyncMaster P2350 connected via MiniDisplayPort > DVI adapter. Works great 90% of the time.
I use the monitor primarily as my main and have the MBP lid closed.
Sometimes when waking the MBP by moving the mouse the screen will come back up all fuzzy (much like an old television on no channel). I then turn the monitor off and back on and the picture returns..!
I know this is not the monitor or the adapter itself as a friend came over a few weeks ago with his adapter and we connected the MBP to my Panasonic Plasma and initially had the same problem.
Has anyone else experienced this? The fuzzy colours as mainly made up of purples, blacks and whites.
Thanks,
Brett

The weird thing is that every morning, when I move my mouse to wake the computer, both displays go from black to show the desktop but the second display immediately goes back to black. Unplugging it and plugging it back in eventually works after multiple trys. Restarting the computer sometimes works but not always.
The only other major change to my computer before this started happening is that I installed Leopard.
So far I've tried setting my Macbook Pro not to go to sleep but that didn't change anything.
Should I try setting my displays not to go to sleep either? I haven't tried that because Energy Saver warned me that it could reduce the lifespan of the display.

Using Second Monitor Airport Does Not Reconnect Upon Waking from Sleep.

Using: MBP; OSX v10.6.5; Airport v5.5.2; Menu Bar assigned to second monitor which is a ViewSonic plugged in via mini-display port to HDMI.
When MBR goes to sleep and wakes upon mouse movement Airport does not re-establish the connection to my network.
No closing of lid or manually putting MBP to sleep involved. Just leave lid open on MBP and walk away for an hour. Upon return, move mouse, everthing wakes except Airport which shows an exclamation mark in the menu bar for the Airport ICON.
When using MBP display for the Menu Bar screen Airport wakes OK.
What's with that behavior???

I changed channels from AUTO to Ch 11. Was there a specific frequency you had in mind.
I also closed the lid to the MBP, let things go to sleep, returned to the office, moved the mouse and the Airport came on line on its own.
I figure there is programmatic problem within either the OS or the Airport coding that prevents Airport re-finding a network with both displays active but the Menu Bar on the secondary screen.

Dual boot OS X 10.10 plus OS X 10.6.8 on new 2014 Mac Mini?

Hi,
I am currently thinking about buying a 2014 Mac Mini. As I still need to use some very expensive (albeit old) software, I would like to run a copy of OS X 10.6.8 (strapped for cash).
I currently own a 2011 MacBook Pro 17" and I have partitioned the disk and run OS X 10.9.5 on 700GB and OS X 10.6.8 on 50GB. This has worked great for the past 2 years. I simply press ‘alt’ on booting and select my OS depending on which software I need to run.
My question is, can I do the same with a new 2014 Mac Mini using one of my Time Machine back-ups (install from Time Machine option on istall)?
I would be very grateful to anyone who can offer me some advice.
Many thanks,

John Lockwood wrote:
Other than running Mac OS X 10.6.8 Server in a virtual machine as previously suggested your next best option is to consider buying a secondhand older Mac that is capable of running 10.6.8.
Just to make it clearer, 'ordinary' 10.6.8 is not allowed due to Apple's license terms to be run in a virtual machine only the 'server' version is. The server version of 10.6.8 can run normal applications and you do not have to use the server bits itself. If you try installing the 'ordinary' 10.6.8 in to a virtual machine it will not work as they check for this.
The new 2014 Mac mini will not run 10.9.5 either, the 'oldest' version the 2014 model will run is 10.10, it will of course also run 10.10.1.
1)     Older Macs are just that: older and out of warranty. So of course the user is subject to the risk of hardware failure without necessarily much warning and little or no recourse (other than purchasing another older Mac) when the hardware does fail. This may also be a different problem for the OP, as cost appears to be a major consideration here.
2)     The use of Snow Leopard Server in Parallels will cost about $99 retail (less, if some shopping for "discounts" on Parallels is done on the internet).
Installing Snow Leopard Server into Parallels for DUMMIES:
http://forums.macrumors.com/showpost.php?p=17285039&postcount=564
3)     It was a common myth that the Snow Leopard EULA prohibited its virtualization in Lion and thereafter on a Mac. That myth has been debunked in the 3-1/2 years since Lion was first released and repeating it now does not make anything "clearer" but only tends to confuse an OP.
In any event whatever remains of that long forgotten debate is now mostly moot since Apple reduced the sales price of Snow Leopard Server by 95% (by telephone orders only; 1.800.MYAPPLE (1.800.692.7753) - Apple Part Number: MC588Z/A); that is, for the same $20 as it sells Snow Leopard client and it is much easier to install, use and maintain Snow Leopard Server in virtualization, including Parallels.

2008 Mac Pro restarting itself after waking from sleep

Recently, my Mac Pro has taken to restarting itself unasked upon waking from sleep. I just moved to a town with a hot summer, and my room has no air conditioning and gets quite warm. Could the temperature in the room be causing this? I don't think so, because it happens in the cool of the morning after an all night sleep, too.
Another factor I just discovered is that one of my RAM chips has stopped showing up in the system profiler.

Replace the pair of DIMMs first.
Monitor the temps inside.
Install and use SmcFanControl 2.2
Run Apple Hardware Test
You may want to try a clean system install to test with once you have the RAM replaced. Faulty RAM can cause all kinds of issues. And dirty files. Some deeper check for corrupt files than Disk Utility is probably in order.
There is a significant "Inrush-current" on boot and wake from sleep with the 2008s. They need good power, a 1500VA/900W UPS, and sensitive to other equipment on the same circuit.
Inrush current

Network connection lost after waking from sleep

iMac (27" late 2013) running Yosemite 10.10.
Ethernet connection direct to the computer from the FIOS router.
Upon waking from sleep, the computer is not connected to the internet.
After about 20 seconds it finally reconnects.
Under Mavericks it never lost the connection by sleeping - was instantly connected upon wake up.
I tried creating a new location under the network system preferences and ordered it so that Ethernet was the first to connect.
That didn't change anything.
Any suggestions how to fix this? I don't want to have to wait every time I wake up the computer.
Really bugging me.

Update on my situation.
I have tried many things to get this fixed including:
SMC reset (for an iMac this means unplugging it, waiting, and plugging back in)
PRAM reset
deleted the "system configuration" folder
Still no luck. Upon freshly booting the machine, it gets to the desktop and opens up mail for me, but the internet is not connected right away. Still takes an additional 15seconds or so after Mail boots up to get a connection. Then everything works fine. If the computer sleeps, it doesn't have internet upon waking, but again will establish a connection (self assign an IP address) after about 15-20 seconds.
So while not crippling, these 15-20 second waits are very annoying.
Interestingly, this is ONLY with a wired Ethernet connection. If I use WiFi everything connects right away. But my WiFi is slower than the wired connection and I prefer to use the wired connection.
Any further suggestions are welcome.
Chris

2014 Mac mini doesn't scale the entire HP Envy 32 monitor screen

I recently purchased a HP Envy 32 monitor for use with my 2014 Mac mini with the Iris display. I get 2560x1440 resolution at 60 Hz on both the DP (1.2) as well as the HDMI ports (using the auto-detected HP Envy 32 color profile) but the display doesn't scale the entire screen of the monitor. Is anyone else using this configuration successfully? If so, what have you done to make full use of the 32" monitor real-estate? I simply cannot find any options in Display preferences (Yosemite) to change underscan options or for that matter within the monitor itself. Is there a particular display profile or driver I can use to fix this issue?

I'm using a 4K compatible DP cable connected to the Thunderbolt port and getting to the max resolution of the monitor. So I don't think the issue lies there. I was able to use SwitchResX trial mode to discover an underscan option that allowed me to scale to the entire monitor screen. Assuming SwitchResX is manipulating core OSX functions, I'd assume there is some display related configuration within OSX that I should be able to tweak in order to scale the monitor screen natively in OSX without requiring any 3rd party software. Any thoughts for how to go about tweaking the display natively?
Thanks

2014 mac mini dual monitor problem

I just brought a mac mini (Late 2014) i have two displays monitors connected, one HDMI to DVI. and one thunderbolt to DVI. I can have both thunderbolts connected and the problem its the same, when back from sleep ,one monitor doesn't turn on. i have to disconnect one and then both work, it only happens when the mac goes to sleep. on cold restart or turning the mac on, this problem doesn't occur. any help.

I have this same problem too. I purchased the Mac Mini with the intention of running dual monitors. I'm using the HDMI and mini-display/Thunderbolt to DVI. I've also tried MiniDisplay/Thunderbolt to HDMI and I'm experiencing the same problem as angelfromfullerton. Whenever it tries to wake from sleep, it can't decide on monitor arrangement and keeps flicking between the two, making the OS unusable and forcing a reboot... EVERY TIME. I've also experienced the issue once or twice on a cold boot. It doesn't matter which Thunderbolt port is used either.
I'm going to have to return my Mac Mini unless this problem is fixed asap.
Mac Min, OSX Yosemite (10.10).

I want to connect a Mac mini to a Samsung 40", Whats the best way to do this?

I want to connect a Mac mini to a Samsung 40" LED tv to use as the monitor, whats the best way of doing this?

Understand that there is one HDMI port on your TV that is specifically designated for PC connectivity. The order that the TV or Mini are powered on may determine your results. For your specific TV model, check buyer reviews on Amazon or elsewhere that can include optimum TV/Computer settings adjustment for improved viewing results.

Can I use a VGA/DVI-D monitor to a new 2014 Mac Mini?

My wife's PC just died (it was a cheap 300 pc that lasted probably 5 years.
She basically emails, web surfs, looks at pictures and plays candy crush on Facebook so she doesn't need anything too high end.
I was thinking of getting her the basic 2014 mac mini but I have a VGA/DVI-D monitor (an older Dell) and it fits perfectly on her desk.
Can I somehow hook up a new mac mini to either the DVI-D or VGA input?
If not, what is the best monitor to get HDMI or should I look into a thunderbolt monitor?
Thanks,

Yes. You will have to purchase one of the following adopter:
- HDMI to DVI and use the Minis HDMI output
- Mini displayport to DVI adopter and use one of the Minis Thunderbolt ports
- Mini displayport to VGA adopter and use one of the Minis Thunderbolt ports
I would use the monitor's DVI input over the VGA input

What cable do i need to use to connect my grandson's old style external isight webcam to his 2014 Mac mini in order for him to be able to FaceTime me

what cable do i need to use to connect my grandson's old style external isight webcam to his 2014 Mac mini in order for him to be able to FaceTime me

You need either a FireWire 800 to FW 400 cable or a FR 800 (male)/FW(female) adopter.
However. it the Mini (note that you still have the late 2012 Mini, Apple has not updated the Mini since then) has Mavericks it may not work satisfactorily. I tried it on my 2102 and I get abount 1 frame every 20 seconds. Another uses posted same problem.
However, it it work fine on my late 2009 Mini with Mavericks

How to mirror iMac screen wirelessly through a mac mini connected to an hdmi port of HD TV?

I have a new Mac Mini connected to a Sony HD TV. On the same network but in a different room I have my iMac. I can control the iMac with wireless mouse and keyboard from the same room where the TV and Mac Mini reside. I would like to work on my iMac but use the HD TV as my monitor so I can show slideshows and iMovie projects without transferring files to the MacMini first. Is it possible, and if so, how do I go about setting it up?

Your iMac likely supports a higher resolution than the TV does. The maximum standard TVs today use is 1920x1080, and if your iMac is an Intel Core i3 or i5, its own display is at least that high of a resolution. Which model of iMac do you have?
If your iMac is running at least Leopard (10.5), then both machines have Screen Sharing built in. It can be accessed from the Finder, but as often as you would like to use it you should go to Macintosh HD > System > Library > CoreServices and drag it (the icon) to your Dock. That will create the shortcut to get to it easily. As I noted before, the built in Screen Sharing VNC software doesn't do full screen, but third party VNC software can. Both machines do not need to be using the thrid party VNC software, just the one viewing - in this case your Mac mini. Chicken of the VNC is a popular free one, fairly easy to use:
http://sourceforge.net/projects/cotvnc/
For more info about how to set up Screen Sharing and how to use the included application:
http://mac.appstorm.net/how-to/os-x/using-screen-sharing-in-os-x-leopard/
Note that you will have to use the settings in System Preferences, regardless of what VNC software you use. Both systems will need to have Screen Sharing settings enabled.

2014 Mac Mini connected to Samsung s22b310b monitor colors bad upon waking from sleep.

Similar Messages

Maybe you are looking for