27" LED Cinema Display – noise and buzz

Hello,
I recently purchased a second hand 27" Apple LED Cinema Display, and I now started to have some issues.
The first issue started today, it is some kind of buzz that comes out of the right speaker whenever I lower the brightness of the screen. I have about the opposite happening for other people – whenever the brightness would be above 3/4, a buzz sound would come up. For me it's when the brightness is below 1/4. The lower the brightness, so higher the pitch of the buzz. How weird is that?
The second issue is that, whenever a sound is played, some kind of white noise starts coming from I believe both speakers of the display. Even if I just adjust the volume on the keyboard (which makes a sound as well), this white noise would come up. It would last around 15-30 seconds, and then it would disappear. If headphones are connected to the Mac Pro, it doesn't happen (and it can't be heard in the headphones either). I once hooked up the Mac Pro to a Panasonic TV to test, and there was no buzz coming from the TV either.
Now I just noticed that the white noise is constantly here since the buzz appeared today (when I lower the brightness). Something is failing here I believe. It could also be the graphics card I guess?
Sometimes I get a very quick weird flash on the screen (black & white stripes I believe) for half a second, then they're gone. It's quite rare so it's hard to troubleshoot. Maybe it has to do with the Cinema Display as well. Or perhaps it is my graphics card (It's a Sapphire HD 7950 3 GB – the Cinema Display is connected with Mini DisplayPort). Or it might just be bad drivers for this card – they were never that good apparently.
Perhaps someone knows more than I do
All helps is appreciated…
Cheers!

No ideas?

Similar Messages

  • 27 LED Cinema Display Audio and Brightness when powering MacBook Pro

    When my 27 LED Cinema Display is powering my (or another) 2009 13" MacBook Pro, I have experienced three issues:
    1. The dropped audio problem other users have mentioned. Shutdown, then disconnect power/usb/displayport, then wait ~15s, then reconnect and reboot temporarily fixes the problem.
    2. I also have the sluggish keyboard behavior when adjusting the volume that others have mentioned.
    3. I have experienced shifts in display brightness which are obvious when the display is dimmed. I have disabled the ambient light sensor as well as any interfering power management or energy saver settings. Opening apps, scrolling and other normal activities seem to aggravate this behavior.
    This last strange behavior inspired me to try using a power adapter for the MacBook Pro instead of display's laptop power connector. *Doing so seems to have resolved all three issues.*
    It seems that this may indicate an underlying problem with the display's power supply. Can anyone confirm?

    mmayo wrote:
    I am having the same issues & with a 1 day old display. I am using a 15" MBP. The screen is killing me when it dims down when no lights are on. I didn't notice the issue when the screen is brighter with the lights on. Anyone know if this is a hardware or software issue? I'd like to utilize the ambient light sensor but not if its going to make my screen flicker when it is dim....
    (1) I have never had any deaths associated with my screen, but on rare occasions my display's brightness will flicker when I manually adjust the brightness. The fix I have found for this is to increase the brightness one more setting or decrease it one more setting. Changing the screen from full dim to full bright and then setting the brightness I want sometimes helps, too.
    (2) You can check whether this software update has been applied to your 27-inch:
      http://support.apple.com/kb/HT4293
    (3) Your Apple Service Provider could tell you whether your problem is related to hardware or software.
    Mac Pro Quad Core (Early 2009) 2.93Ghz Mac OS X (10.6.4); MacBook Pro (13 inch, Mid 2009) 2.26GHz (10.6.4)
    LED Cinema Display; G4 PowerBook 1.67GHz (10.4.11); iBookSE 366MHz (10.3.9); External iSight; iPod touch 4.1

  • Foggy LED Cinema Display

    I just came back from the Holidays, booted up my computer connected to my LED Cinema Display screen, and within 15 minutes, a large gray blurring blob was projected on my screen. It takes up nearly half of the screen. I've never had any issues with the screen prior to this. The odd thing was that the screen was fine initially and then boom, the ghostly blur appeared. Has anyone else had these issues? Reading past inquiries, someone declared it could be due to possible condensation.  My computer isn't in a moist environment so I don't see this as a possibility.

    could be either display cable or display itself, unsure how to figure out between the 2, though

  • Annoying Screen saver/Login window/Apple LED Cinema Display Bug

    Hi all,
    After upgrading to 10.6.4 I have a really annoying problem.
    First the relevant setup information: MacBook Pro 17 inch (2009 model), 8 GB RAM, 10.6.4, Screen saver activates after a few minutes with password protection and a few minutes thereafter the screen is put to sleep.
    Here is what happens: whenever I have an external Apple LED Cinema Display connected and I move the mouse while the screensaver is activated, I am able to type my login and password, but after that in just a matter of seconds (usually 3-4 seconds) the both screens become blue and all my programs close and Mac OS X jumps to the login screen (all data that was not saved is gone, all open windows also gone). This bug does NOT happen if the Apple LED Cinema Display is not connected.
    Anyone else experiencing this issue?
    Best Regards,
    Michael

    Hello guys, thank you for answering.
    Yes, the USB cable is plugged.
    At the moment I'm avoiding to flash the VRAM. But I found out that restarting my system gives me access to the controls again. It does randomly stop working. Sometimes I can adjust the cinema display settings but not the macbook screen settings. In my opinion it is definitely a bug.
    There is any way to submit a bug somewhere?

  • Does your new 27" LED Cinema Display buzz?

    Got my 27 inch LED Cinema Display yesterday: very nice monitor.
    However, I have noticed a feint buzz/ticking coming from the bottom right of the monitor when the brightness is set high. Just loud enough to be VERY annoying!
    Is this a feature of the monitor? Does anyone else's new 27" Display have a buzz?

    yes, the reason it sounds like the electromagnetic interference that induces tones in speaker drivers (such as the microwave energy from cell phones) is because it is essentially the same mechanical action... which is a resonation electromagnetic coil (which will produce tones at whatever frequency it is vibrating).
    The specific tones that it is producing are dependant on the electrical properties of the circuits attached to the coupled device - but it's probably possible that particular properties could cause the coils to create more than a single tone (just like a speaker)... on mine the tone didn't quite sound singular, but since the amplitude was analogue to the brightness i guessed that this pointed the transformer.
    It used to be such a serious problem in inductively coupled conductive devices that it could shake the devices to pieces. These days it's only really an irritation in terms of noise - but it remains necessary to design the structure and housing of these devices to dampen and minimise these vibrations.
    In much larger transformers the noise is very noticeable (have a listen the next time you pass an electrical substation).
    ... i could be wrong but it's a common problem in electronics and i think it's likely.

  • Horizontal shifting bars on MBP 15 after disconnecting 24" LED cinema display and waking up from clamshell mode.

    I use my MBP 15 (late 2011) with 24" Apple LED Cinema display in a clamshell mode. After disconnecting external display, and opening display, it shows horizontal shifted bars, so it becomes completely unusable. Have to hard reset laptop. Any hints on how to resolve this? Thanks.

    Ok, more information for anyone that might care. The wake-up seems to be the familiar dark wake in order to go into hibernate mode. Except now, it's a death wake. Looking at the logs, I see that it happens exactly 70 minutes after sleeping, even though hibernatemode = 0 (which shouldn't hibernate at all!)
    So my power settings look like this:
    Currently in use:
    standbydelay         4200
    standby              1
    halfdim              1
    hibernatefile        /var/vm/sleepimage
    darkwakes            0
    gpuswitch            2
    disksleep            10
    sleep                10
    autopoweroffdelay    14400
    hibernatemode        0
    autopoweroff         1
    ttyskeepawake        1
    displaysleep         2
    acwake               0
    lidwake              1
    standbymode is 70 minutes, what a coincidence. I'm going to try setting it to 0 and see what that does.

  • Under Windows 7 Ultimate x64 and Boot Camp, my 27 inch Apple LED Cinema Display checks out as a Generic PnP Monitor and is shown as NOT HDCP compliant.  I haven't been able to find any kind of an .inf file to use.  Does anyone have a solution?

    Under Windows 7 Ultimate x64 and Boot Camp, my 27 inch Apple LED Cinema Display checks out as a Generic PnP Monitor and is shown as NOT HDCP compliant.  I haven't been able to find any kind of an .inf file to use.  Does anyone have a solution?  Or is Apple's implementation of HDCP (if it's there) incomplete?

    I am having this same issue. Im not sure if this is the cause but I think this is keeping PowerDVD Ultra 11 from playing back Bluray under Windows 7 / Bootcamp

  • VMware Fusion and Apple LED Cinema Display

    I have a 2008 MBP and a 27" Apple LED Cinema Display. My OS is 10.7.2.
    I am running Windows 7 with the latest updates in VMWare Fusion 4.1.1. I have several issues.
    1) When I go to chose my monitor it say Apple LED Cinema Display but "Generic Non-PnP Monitor." I downloaded and installed the boot camp drivers as I understood those contained the drivers for the monitor, but that didn't seem to help. Do I need to have the Boot Camp drivers?
    2) When I try to access the Boot Camp Control panel in Windows 7 in Fusion I get "An error occured while tyring to access the startup disk settings. You may not have privileges to change the startup disk." My guess is this is because the Boot Camp drivers are only needed if you actualy run Boot Camp.
    3) In Windows I cannot choose the native resolution of the Apple display (2560 x 1440).
    4) The resolution ia 1277 x 1234. That is weird.
    5) If I minimze the Fusion window and then immediately open it, it looks fine. But if I wait for awhile and open it, the window will be black until I click inside of it.
    Something is wrong, Any help in fixing this would be greatly appreciated.
    Bryan

    you have to separate out what is Fusion and what is Windows native.
    Even doing updates to Windows sometimes should not or cannot be done properly in VM.
    And there is no way to change the default boot drive - a VM doesn't have access and that is the host OS's job, not the guest's.
    Install the latest AMD driver for mobility - and dont' use the "auto detect" - that is not going to work on Apple hardware.
    You dont' run Boot Camp. But the Apple drivers and serives needed for hardware support, yes, they aren't running or loaded.

  • New Mac Pro and LED cinema display

    Sorry if this has been asked before, I tried searching for it but none of the topics answered my question specifically enough.
    I have a 24" Apple LED Cinema Display purchased less than a year ago. Will it connect to a new Mac Pro and what happens to the power cable that's attached to the LED display?

    I have a 24" Apple LED Cinema Display purchased less than a year ago. Will it connect to a new Mac Pro
    Yes. All the standard cards that come in the Mac Pro have one Mini DisplayPort. The 24"LED display will plug into that.
    and what happens to the power cable that's attached to the LED display?
    It is not used if you don't have a MacBook.

  • I have a macbook connected to LED cinema display. The display started to flicker. The display turns black for a second or two. Sometimes I restart macbook and display. Sometimes it helps.

    I have a macbook connected to LED cinema display. The display started to flicker. The display turns black for a second or two. Sometimes I restart macbook and display. Sometimes it helps.

    same issue, either your wiring or display itself is going bad. for me, it was the display but luckily still under warranty

  • Screen resolution problem - HP computer and LED Cinema Display

    I just purchased an HP Envy Phoenix H9-1330 with Windows 8, and I connected it to my 27" Mac LED Cinema Display, but the resolution is horrible. The highest option in the screen resolution menu is 1280 x 720, and I'm getting the error message "Your resolution is lower than 1024 x 768. Some items might not fit and apps might not open". How do I fix this? What kind of issue is this (Windows 8? Graphics card? HP can't support my monitor? etc...)?
    I just bought another brand new computer, but not an HP, with Windows 8 and I have no problems with the resolution - it looks absolutely beautiful. I want to use my monitor with my HP desktop though.
    Thanks for any help

    Still haven't figured it out....
    BUT I did notice that, on the back of the computer, there are 2 additional DVI connections that are covered with a black cover and screwed in (and they say 'please do not remove'.... I'm asuming it's because they aren't connected to anything? Or maybe they aren't connected to the graphics card?). Is it possible that just my DVI connection is wrong, and I'll need to connect to one of these covered-up DVI inputs instead? But why are they covered up? Do I need to take it in so they can be connected to the graphics card?? Help! I don't want to return this computer, but I will have to if I can't get the resolution fixed.

  • LED Cinema Display (27-Inch) and the new iMac (late 2012)

    Does the LED Cinema Display (27-Inch) work with the new iMac (late 2012) as a second monitor, and if so, which cable do I need?

    It will work.  Plug its Mini DisplayPort plug into the computer's Thunderbolt port.  No adapters needed.

  • Question about the new 27" LED Cinema Display and text size

    Hi, I own the 24" Apple LED Cinema Display and text on the monitor is just large enough for me. Won't text on the new 27" Display be much smaller with its higher resolution?

    MANY thanks for the tip.
    Now then - all indications are that my Mini will NOT pass audio via the MDP Cable given the age as well as the lack of an HDMI port (I know there isn't one this rig).  Unless I am missing something I don't believe there is any adapter out there that will allow the audio to now pass through the MDP Cable if the rig itself was never configured to do so.
    Following links in your posting, someone recommended this: 
    http://www.monoprice.com/products/product.asp?c_id=104&cp_id=10428&cs_id=1042802 &p_id=6331&seq=1&format=2#description
    However it seems to be set up to deliver A/V to an HDMI display, and unless I am mistaken, the 27" LED ACD does not have an HDMI in.  Although my MacMini does have a S/PDIF Optical Digital Audio Output I don't believe the 27" LED ACD has any kind of separate audio input (either TOS Link or even 1/8 smini stereo).
    So I reckon I am SOL with regard to getting the audio onto the new monitor from the Mini and I would need to keep my present speakers set up using the 18/" mini stereo out - but the video should still work......yes?  

  • Photoshop issues with MBR and LED Cinema Display

    Hi,
    I have my MBR 15" connected to a 24" LED Cinema Display. In Photoshop, when dragging windows to the secondary display (the Cinema Display) they turn immediately black. If I drag them back to the main monitor (the MBR) they will show up normally.
    Now, if I change the main and secondary displays (1st-CD; 2nd-MBR), this will happen again on the secondary.
    I really need to have both displays working with Photoshop. Does anyone know a workaround to this? 
    Thanks in advance,
    Jorge

    Sorry, forgot about that. It's Photoshop CS6, already updated to be Retina capable (version 13.0.2).
    I'm going to check for further updates.

  • Difference between a Apple LED Cinema Display (27" flat panel) and a Apple Thunderbolt Display (27-inch)?

    May i know the difference between a Apple LED Cinema Display (27" flat panel) and a Apple Thunderbolt Display (27-inch)? both products look the same to me, even the prices are the same, but the name of the product is different. Its so confusing! I want to purchase a secondary display for my 21" iMac, but idk the difference between the two.
    furthermore, another question i have is, is 27" the largest display i can get? is there larger ones (just the screen, not the computer)?
    please help, thanks!

    rae90 wrote:
    May i know the difference between a Apple LED Cinema Display (27" flat panel) and a Apple Thunderbolt Display (27-inch)? both products look the same to me, even the prices are the same, but the name of the product is different.
    One has thunderbolt capabilities, the other doesn't.
    is 27" the largest display i can get? is there larger ones (just the screen, not the computer)?
    No you can get a larger one.  Maybe not an Apple one, but certainly another brand.

Maybe you are looking for

  • NFe de devolução de compras (layout 3.10)

    Ao processar um cenário de Devolução de Compras (MIRO - Nota de Crédito), a NFe de devolução (layout 3.10) não foi validada no SEFAZ. O motivo da recusa foi o "225 - Rejeição: Falha no Schema XML da NFe". Verifiquei que esta rejeição se deve ao fato

  • PP - Explosão de BOM Phantom em Ordem Planejada

    Olá pessoal! Tenho um cenário onde dentro do meu Produto Acabado, tenho vários componentes organizados em  Grupo de Alternates, e para cada grupo, defino um componente como Principal ( 100% de utilização ) e os outros como Opcionais ( 0% de utilizaçã

  • Regarding TDS E Return.

    Pls Help, Any body create logic of TDS E Return .which is quaterly basis. Pls  do the needfull. *Assign full mark. regards, mahi

  • Session variables in jsp,php

    Dear friends, is there any way tht i can pass the session variables set in a jsp file to a php file. Is there any way to do this apart from setting cookies? plz help!! bussa

  • Where do I find out which operating system is on my imac desktop computer?

    How do I know whether or not I have an XP operating system on my imac desktop?