5 second delay  when using server name instead of ip in JNLP codebase??

Hello,
can anyone think of why, in my jnlp file when I have codebase="http://www.mysite/..." my rmi app has an additional delay of 5 seconds when making RMI calls? If I replace www.mysite with 64.29.187.xxx (i.e the ip used to access the server form the internet) my app runs flawlessly, no 5 second delay.
I am using java 6.0.
Any ideas? Thanks in advance.
SC

Thanks for the tip Khumar... A few more questions:
1) Why is it still using the DNS after it's loaded the jnlp. To access my RMI server I'm already using an IP address. In other words, this should resolve during the jnlp loading time. Why is it interfering with normal operations after the app is up?
2) All the jars have already been loaded. There should be no further need to access a DNS, as there's nothing further to resolve
3) Is there a way to cache the IP addy that the server name translates to?
Thanks in advance,
Sal C

Similar Messages

  • Screensharing crashes on login when using server name

    I have three Macs, let's call them A, B, C, all running Snow Leopard. My main Mac is A. I have screen sharing set up on the other two Macs and until yesterday it worked fine. Now, I can still see B's screen from A as usual. But when I try to see C's screen using Go > Connect to Server and entering its name (C.local or vnc://C.local) or using Go > Home, clicking on C on the sidebar and choosing Share Screen, it does not work. The Screen Sharing app brings up a login dialog for C (which it has not done since I first connected to C long ago) and when I enter the correct login information, after a bit the Screen Sharing app crashes and leaves the login dialog hanging. I have to use Activity Monitor to quit NetAuthAgent to close the dialog.
    I can connect to C from B with no problem, and I can connect to C from A if I use C's IP address (vnc://xxx.xxx.xxx.xxx) but not if I use its name. I can also see C from A using Chicken of the VNC. And I can connect to disks on C.
    Of course, I have tried restarting A and C, and I have tried deleting the Screen Sharing prefs file (com.apple.ScreenSharing.plist) from my user Library on A (and restarting). I thought the problem might be with keychains, so I ran Keychain Access, and I noticed that there were vnc keychain entries for B but not for C. So I tried manually adding keychain entries for C. No differece. Then I deleted all keychain entries for C, which did not help.
    Something on A that is specific to screen sharing C by name got clobbered, but I am at a loss what it might be or how to fix it.

    The only time it fails is in windows 7 and the address used of HTTP://servername. I updated the above post to show it works in XP with ff12.
    There is no proxy server involved.
    I am logged into the domain.
    If I use the fully qualified servername as the address it works. Http://servername.domain.local

  • 30 to 40 second delay when printing a PDF

    I have a PC running XP Pro- after a recent trip to the repair shop for a failed hard drive I am now experiencing a 30 to 40 second delay when trying to print pdf's. When I have a pdf open I click on the printer icon and then wait 30 or more seconds for the print window to open to select how many copies etc... after it opens I select print and then another 10 to 15 second delay before printing.
    I was advised to go to the advanced on the print page and select to print as Image. This has not helped.
    I have reinstalled the latest Adobe Reader as well as reinstalled printer. Nothing has helped.
    Word documents print perfectly.
    Any help would be appreciated -wasting lots of time at work!
    Thanks!
    Ray

    I have a similar issue and have up to date drivers. Printing from other programs (eg word/excel and all my other software!) is "instant". The delay within Adobe Reader is only for the first document of the day. This issue has persisted from v9 to v X that I am currently using. I have uninstalled and re-installed Reader with no chnage.C'mon Adobe ... there must be a fix for this! For info I am running a Win7Pro w/s on a SBS2003 network, one printer is attached to the w/s by USB, the other printer is a network resource.

  • Delay when using Airport Express

    a friend hooked up an airport express yesterday in a place with a few macs - there seems to be about a 2 second delay when clicking on any mp3 song in itunes. Is this normal?
    Any way to reduce the delay?

    Thanks snives,
    You're talking about Airtunes right
    Yes, Airtunes.
    Try to not let it bother you.
    Just can't use it for professional timing needs - so useless for us...
    Alternative wireless methods would be to transmit raw audio using another device
    * interesting - what other device are you thinkng of?
    or use an audio cable if that's possible in your situation.
    already tried that - works fine - but don't want the cable

  • IPhone 4s Voice Memo App has 5 second delay when the record button is pressed. When it starts recording, it goes from 0 seconds to 5 or so seconds recorded. This happens randomly and often and sometimes has the delay but starts at zero. Solution Anyone?

    After iOS 7 update, my iPhone 4s Voice Memo App has 5 second delay when the record button is pressed. When it starts recording, it goes from 0 seconds to 5 or so seconds that it shows has recorded. This happens randomly and often, sometimes it will have the 5+ second delay but starts recording at zero seconds. Besides the delay it has been working fine as far as saving and playback is concerned. I have plenty of storage on the phone itself and it NEVER had this problem before I updated to iOS 7. I've reset the phone a couple times by holding down the power and home buttons at the same time. The reason I have an issue with this is that I'm always recording song ideas, melodies, and scratch takes; what I'm saying is when I come up with an idea I need to be able to know that when I hit record it will start right then so I don't forget anything that has just popped in my mind.
    Does anyone have a solution or suggestion?
    Thanks

    After iOS 7 update, my iPhone 4s Voice Memo App has 5 second delay when the record button is pressed. When it starts recording, it goes from 0 seconds to 5 or so seconds that it shows has recorded. This happens randomly and often, sometimes it will have the 5+ second delay but starts recording at zero seconds. Besides the delay it has been working fine as far as saving and playback is concerned. I have plenty of storage on the phone itself and it NEVER had this problem before I updated to iOS 7. I've reset the phone a couple times by holding down the power and home buttons at the same time. The reason I have an issue with this is that I'm always recording song ideas, melodies, and scratch takes; what I'm saying is when I come up with an idea I need to be able to know that when I hit record it will start right then so I don't forget anything that has just popped in my mind.
    Does anyone have a solution or suggestion?
    Thanks

  • Can you merge two user accounts on macbook? my wife has created a user on her new macbook , then inadvertently created a second one when using the migration tool. 1st ac has her office 365 install, yet 2nd has her itunes database, docs and contacts.

    Can you merge two user accounts on a macbook? my wife has created a new user on her new macbook air then, inadvertently, created a second one when using the migration tool. 1st a/c has her office 365 install, while 2nd has her itunes database, docs and contacts. What is the best way forward to get everything into the one account? Not sure if the office 365 will allow another installation into the second account, otherwise would just do that and delete the first, if that is possible?

    There is no merge but you can move data from one account to another via the Shared folder. Data is copied from Shared. Watch your free space when copying. These are large files.  Do one at a time if you are on a small drive. After making copy, delete from other users before you start next copy.
    Office365 installs in the main Applications folder and is available for all users on the computer. Activation is tied to the drive not the User.

  • Midi Delay when Using Rewire?

    I am experiencing really bad midi delay when using
    LE7.1 & Reason 3.0 in Rewire mode.
    Should this be happenening? I take it that I am setup properly for rewire or I would not hear anything at all. I can trigger Reason synths via LE in rewire mode but the delay is so bad that it is unplayable.I thought "latency" issues only occured when using audio. I have tried different buffer sizes to no avail.
    Any ideas?

    ok I'll answer my own post.
    Issue was a toggle box in LE prefs to control "Rewire Behaviour". Set it to "Live mode" not "Playback" mode solves this issue.

  • When connecting to website using sso, packet sniffing shows ntlm user is using {server name}\{user name} instead of {domain name}\{user name}

    I moved to windows 7 and firefox 12 and my internal website via the servername (not FQN) is now prompting me for the username and password in firefox. I do not get prompted for a username and password when using IE9 to access the site via servername (not FQN).
    packet sniffing shows IE9 is using my windows domain as the windows domain. packet sniffing shows Firefox is using the web servers servername as the domain.
    If I use the fully qualified server name then firefox authenticates successfully. this is not a problem on my winxp workstation with firefox 12.

    The only time it fails is in windows 7 and the address used of HTTP://servername. I updated the above post to show it works in XP with ff12.
    There is no proxy server involved.
    I am logged into the domain.
    If I use the fully qualified servername as the address it works. Http://servername.domain.local

  • Reports with wrong Server details (using ODBC name instead of server name)

    Post Author: jomuir
    CA Forum: Administration
    When I save a report either in Crystal Reports 11 (File save as, Enterprise u2013 Central Management Server) or Central Manager Console, Objects New Object I get an error.
    On looking at the database all reports I am adding or saving are automatically taking the wrong server details, and it is a greyed out field, so I cannot edit it. I presumed it is getting this information from my ODBC settings, but appears to be using the ODBC name/description as the server name (The Database and usernames are correct). This is happening on every report!
    Any ideas what I am doing wrong? How I can save or add new reports with the correct details?
    Not sure if this will help, but the error message is:- Failed to open the connection. D:\Program Files\Business Objects\BusinessObjects Enterprise 11.5\Data\procSched\wdcsql1.reportjobserver\~tmp117852b044ee296.rpt 

    Post Author: jomuir
    CA Forum: Administration
    No, Crystal Reports in not installed on the server, and the ODBC settings are not setup on the server. However I did add the correct ODBC settings on the server but this has made no difference.
    So do I need to setup all the ODBC settings in advance of anyone saving a report (I will need to try and find obtain them all)?
    Should the server also have a version of Crystal Reports on it?
    One report is working but it was added by the guy that installed it, and this report is using the same database as all the reports that I have added, and should be the same ODBC settings.
    The server (server username) does not have access to the original location of the reports, so it cannot run the reports - however when I save them to the server via enterprise or the import tool, does a version of the report get saved on the server? If so can you point me in the direction of them, so I can try and run them via the server?

  • Database creation: use machine name instead of ip address.

    I am creating a new database using the Database Configuration Assistant. After the install, it tells me that the EM can be approached through http://192.168.198.128:1158/em. However, since the ip-address is dynamic, i'd prefer to refer to the machine name instead of the ip address. During the setup I could not see where to change this.
    Regards,
    Rick

    user10064100 wrote:
    Thanks for your replies, I will try that. Version info: 10.2.0, on a Windows Server 2k3. The server runs in a virtual machine, which is pretty much the root of the problem: it tends to change ip addresses when restarting it. I will now install the loopback adapter and see what happens.
    Edited by: user10064100 on 8-dec-2008 7:48Ah, a server on a virtual machine. Why didn't you say that in your initial posting? I would think that would be much different situation than the usual 'changing ip' configuration of placing a sandbox database on a DHCP desktop or laptop machine...
    I don't have any experience with VM's, so I'll leave that to those that do. At the least, I'd expect the loopback adapter to not necessarily be your solution. That's for the assumptions that I clearly stated in my first response. If those assumptions don't match your situation (and it is now clear that they don't) then you need consider that before taking any advice based on those assumptions.

  • Delay when using BC partition in VMware Fusion

    Hi everyone,
    I've been wondering about this for months now and finally decided to ask for your experiences.
    When using my Windows (XP Pro 32bit) Boot Camp partition as a VM in Fusion I always get a delay when the desktop appears and the taskbar items are loading. I can see that the VM Tools seem to be loading (taskbar icon) while this is happening. This usually takes at least 10-15 seconds on my MBP (C2D with 4 GB RAM) and it has been the same for the last few versions of OS X and Fusion.
    Is this delay normal when using the BC partition? It definitely isn't there when booting a regular VM. If so, how long does it take for you?
    Thanks!
    Björn

    Nope, KBDMGR.EXE is located in "Program Files" and autostarted via the RUN registry-entry. It's seemingly not even a real driver, but merely a bridging process that administers the drivers.
    If you run bootcamped Windows without KBDMGR you cannot use the special function keys (brightness, loudness etc) and at least in Vista you have to do some manual settings every time you start Windows in order make tap-to-click usable without KBDMGR (a better and easier way is to start KBDMGR once and then stop it again if you don't want/need it).
    Manually enabling tap-to-click and chosing the Boot-OS is possible without KBDMGR being loaded even once, you can just call the settings application from Windows/System32. The Readme coming with my Script explains how to find that and possibly use a keyboard- or icon-shortcut for that.
    Theoretically it can be stopped/killed via Process-Manager and started manually by just calling the exe file. Practically that only works as long as the RUN entry in the registry remains intact and points to an existing file.
    Along other things my script explains how to replace KBDMGR.EXE with a dummy file which in turn allows to start Windows without it and later loading it manually if needed (preferably via a keyboard- or icon-shortcut as described in the Readme of my script).
    Personally I use Right-ALT+, for opening the Settings and Right-ALT+. for switching KBDMGR on/off (along with switching the F-Keys from Standard to Special functions alongways). Works like a charm.
    Message was edited by: T1mur
    Message was edited by: T1mur

  • Significant delay when using the "tap to click" trackpad function

    (I accidently post this in the wrong forum -- for the old MBP -- so this is a repost)
    Hello everyone! I bought a 2.4 Ghz unibody MBP like 3 weeks ago. I had an issue and they replaced the computer with a new one at the store. Today is the first day of using the new laptop. They switched out the ram upgrade and the hard drive.
    The issue seems to be that when using the tap to click function on the trackpad, there is a relatively significant delay (at least for a click). With the regular mouse button the delay isn't there. Such as if I'm clicking on the finder or the file tab, there's a bit of a delay before they pop up, compared to instantaniously with the mouse button. When using the trackpad for regular types of tasks, there is a bit of a delay sometimes too. Such as I'll be moving the mouse across the screen and it will stop.
    Please help me out. If I could solve it without going back to the Apple store that would be great. Thanks everyone in advance.

    Update: I think the 1/2 second delay is too long of an estimate, but the delay is significant enough to make me notice something has to be wrong. My previous MBP had no delay.
    When moving the mouse around, I'm not sure if it's a MBP issue, but occasionally the mouse seems to "get stuck" on the screen and I have to begin moving my finger again on the trackpad. This happened on the first MBP too.

  • ORA-12520 when using SERVER=SHARED

    Hi, I'm using oracle8 client ot connect to an oracle 9i DB. When I connect using SERVER=DEDICATED there's no problem, but when I change it to SERVER=SHARED on my tnsnames.ora I get ORA-12520.
    What should I do?
    Here's my client tnsnames.ora:
    SIAMA=
      (DESCRIPTION =
        (ADDRESS_LIST =
          (ADDRESS = (PROTOCOL = TCP)(HOST = XXXXX)(PORT = 1521))
        (CONNECT_DATA =
          (SERVER = DEDICATED)
          (SERVICE_NAME = SIAMA)
      )My sqlnet.ora:
    SQLNET.AUTHENTICATION_SERVICES = (NTS)
    NAMES.DIRECTORY_PATH = (TNSNAMES, ONAMES, HOSTNAME)And here's the output of lsnrctl services on the server:
    LSNRCTL for HPUX: Version 9.2.0.6.0 - Production on 27-AUG-2009 14:34:02
    Copyright (c) 1991, 2002, Oracle Corporation.  All rights reserved.
    Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=xxxxxx)(PORT=1521)))
    Services Summary...
    Service "CAR1AMA" has 2 instance(s).
      Instance "CAR1AMA", status UNKNOWN, has 3 handler(s) for this service...
        Handler(s):
          "DEDICATED" established:6 refused:0
             LOCAL SERVER
          "PRESPAWN" established:0 refused:0 current:0 max:0 state:ready
          "PRESPAWN" established:0 refused:0 current:0 max:0 state:ready
      Instance "CAR1AMA", status READY, has 1 handler(s) for this service...
        Handler(s):
          "DEDICATED" established:1351504 refused:5549 state:ready
             LOCAL SERVER
    Service "CAR1AMAXDB" has 1 instance(s).
      Instance "CAR1AMA", status READY, has 1 handler(s) for this service...
        Handler(s):
          "D000" established:2 refused:0 current:0 max:2026 state:ready
             DISPATCHER <machine: XXXXX, pid: 8815>
             (ADDRESS=(PROTOCOL=tcp)(HOST=XXXXXXX)(PORT=56707))
    Service "SIAMA" has 2 instance(s).
      Instance "SIAMA", status UNKNOWN, has 3 handler(s) for this service...
        Handler(s):
          "DEDICATED" established:2 refused:0
             LOCAL SERVER
          "PRESPAWN" established:0 refused:0 current:0 max:0 state:ready
          "PRESPAWN" established:0 refused:0 current:0 max:0 state:ready
      Instance "SIAMA", status READY, has 1 handler(s) for this service...
        Handler(s):
          "DEDICATED" established:4066319 refused:3025 state:ready
             LOCAL SERVER
    Service "SIAMAXDB" has 1 instance(s).
      Instance "SIAMA", status READY, has 1 handler(s) for this service...
        Handler(s):
          "D000" established:4 refused:0 current:0 max:2026 state:ready
             DISPATCHER <machine: XXXXX, pid: 8899>
             (ADDRESS=(PROTOCOL=tcp)(HOST=XXXXXXX)(PORT=56722))
    The command completed successfully

    You need verify if Oracle 8i is compatible with this feature from Oracle 9i. Make a test from client machine using client 9i.
    Best Regards,
    Douglas Paiva

  • Delay when using doubletap and hold with bootcamp 5

    Hi,
    I just bought a 15" MBPro and discoverd a delay when I use doubletap and hold to scroll or to mark text or drag. Is this a know problem of the bootcamp trackpad driver?
    Hoping for answers
    Bye
    Michael

    I have the same problem, except that I'm using the Apple Trackpad in Windows 8 in Boot Camp on a 2012 iMac, so my guess is that the driver is to blame.

  • WRT160N V2 - Web Browser unable to find home server using server name, IP address OK.

    Hi, I have just got a WRT160N V2, it is working fine apart from one irritating issue. I am unable to browse a web server running on my local network by the computers (servers) name. If I use the IP address it works fine. Viewing my shared files and folders  with Windows Explorer using servers name also works fine. The problem seems to be limited to web browsers, I have tried Internet Explorer and Chrome, neither can find the server using its name, using IP address they can. I have checked NetBIOS settings on all connected computers and they are ok. If I switch back to my old Netgear router the problem goes away. So, it seems it's something specific the the WRT160N. This isn't a huge issue as I can fix by adding a line in the Hosts file. I just wondered if this is a known issue?
    Many Thanks
    Ian

    The first thing that you can try is upgrading the firmware of the router..
    Reset the router for 30 sec , reconfigure the router again and then try to setup the web browser for the server.

Maybe you are looking for

  • Problems with terminal application - characteristic HD noises

    Hi, I hope you can advise me for the rather obscure problem I am having. I have installed Darwin ports and am using the python app hellanzb, which is an automated usenet downloader. The problem that I have is that now, when starting up the terminal f

  • How do I get rid of updated apps in apps store ?

    I have updated many apps in my App Store but cannot get rid of them after updating, any ideas ?

  • I POD not charging when I tunes recognise it

    Hello, Just bought a video I-POD 60 GIG. I installed the CD, connected the device and left it charging for 24 hours. Then I created a library synchronized it and start enjoying the music. I let the battery run just to see how long those would last. I

  • BlackBerry Passport - double typing issue

    After about 4 months of usage, I began to start having the double-typing issue on my Passport (which, from what I read, is not uncommon, both for Passports and Classics).  It doesn't seem to te be the hardware issue - I can't recreate it by simply pu

  • BPELPortlet.ear file missing

    Hi, I installed a midtier version of BPEL PM 10.1.2.0.0 and ran IRCA.bat and installed ORABPEL schema in the midtier infrastructure. Now I wanted to integrate BPEL and Portal but can't find the BPELPortlet.ear as specified in Oracle® BPEL Process Man