5508 WLC redundancy issue.

I am trying to set up fail-over for Cisco 5508 Wireless LAN Controller which is using 7.4 version software. I setup the redundancy port and peer redundancy.
While checking,one becomes active and other becomes standby.
Its showing everything perfectly including peer,standby-hot etc.(XMLs matched also)
I disconnect the 1st WLC uplink and then the Stand by becomes active. Fine.
Later i connected the 1st WLC link and disconnect the 2nd WLC (currently active). Here comes the issue.
Then other WLC is not becoming Active and it enters in to Maintenance mode. Means Down.
why this issue happens?
One thing i need to highlight is, one WLC is having 50 AP basce license count and other WLC having 250 AP base license count.
Is this will be an issue? Whether the License count should be same on both?
If so,how can i trim-down 250 to 50 AP base license?
Any clues? Help me!

You don't have trim down the license. The license amount is going to be what you have on the primary. As far as failover the way your doing it, I don't thinkers supported that way. Only a hard failure. So you will have to manually switch the primary back.
Sent from Cisco Technical Support iPhone App

Similar Messages

  • Clients unable to connect and get DHCP - LAP1142N AP and 5508 WLC

    Hi,
    I have 19 locations, each with 1 or more LAP1142N AP's in FlexConnect mode, AP's are primed using CAPWAP to my 5508 WLC at the datacenter. The AP's join the WLC without issue every time. I have two WLAN's, one guest and one staff, the guest network is open and obtains DHCP from a WatchGuard XTM33 firewall at each of the remote locations. The staff side is WPA2/RADIUS and DHCP is assigned from the WLC. Each AP is assigned a static IP that is not in the DHCP scope. For example: DHCP scope on the branch firewall is 192.168.1.10-250 the AP will be assigned static IP of 192.168.1.1.. The AP's are connected to a HP procurve switch that has a untagged VLAN, the firewall is using the native vlan 1 and so is the AP.
    I have been running this network for over a year and it has not had a single issue until the last two weeks. Nothing on the network has changed or has been upgraded.
    Now for the issue: The issue I am seeing is that clients are no longer able to connect to the AP and do not get DHCP assigned to them. I am able to get it working, if I remove the static IP from the AP, the AP will reboot, join the controller, then begin working, users can connect and DHCP is assigned from the firewall as it should. However, If the AP then reboots, the AP will join back to the controller but no clients can connect nor do they get a DHCP address. So, I then reassign a static IP to the AP again and it reboots, connects to the controller and clients then can connect and get DHCP.
    Attached is a running config from one of the APs
    I've found several posts on this topic, in fact the patch of unassigning or reassigning static IP is one that I found. However, I wanted to post this to see if there is any further assistance I can get on this. I am also waiting on my SmartNet to start up and will be contacting Cisco support as well.
    Thanks for any help.

    Alright, so I finally figured out the issue with this. I had a Mobility Anchor set on the guest WLAN and once I removed that all started working again.
    What is Mobility Anchor?
    A. Mobility Anchor, also referred to as Guest tunneling or Auto Anchor Mobility, is a feature where all the client traffic that belongs to a WLAN (Specially Guest WLAN) is tunneled to a predefined WLC or set of controllers that are configured as Anchor for that specific WLAN. This feature helps to restrict clients to a specific subnet and have more control over the user traffic. Refer to the Configuring Auto-Anchor Mobility section of Cisco Wireless LAN Controller Configuration Guide, Release 7.0 for more information on this feature.

  • AIR-CAP3702I booting up in mesh mode and not joining our 5508 WLC

    I have a batch of 30+ AIR-CAP3702I-A-K9 APs that I need to setup but none of them are joining to the 5508 WLC and when I connect a console cable and view the output from the AP it shows that it is trying to initiate in mesh mode. I have read other forums that are showing that I need to put in the APs MAC address to a filter list on the WLC for it to show up and then I will be able to change it from mesh mode to local mode. The only issue I'm having with that solution is not knowing how it will affect my current production environment off of that 5508 WLC. I have 69 active production APs with clients working off them and there are no MAC filters currently in place on the WLC. By adding a MAC filter entry for the new APs would the WLC create an implicit deny for all other clients that don't have their MAC addresses entered?? If so is there another work around? Can the mode be changed via the CLI on the AP itself to make it local instead of mesh? 

    sh capwap client rcb
    AdminState                  :  ADMIN_ENABLED
    SwVer                       :  7.6.1.118
    NumFilledSlots              :  2
    Name                        :  AP88f0.4290.7184
    Location                    :  default location
    MwarName                    :  xxxxx
    MwarApMgrIp                 :  x.x.x.x !<it has the correct name and IP of the WLC>
    MwarHwVer                   :  0.0.0.0
    ApMode                      :  Bridge
    ApSubMode                   :  Not Configured
    OperationState              :  JOIN
    CAPWAP Path MTU             :  576
    LinkAuditing                :  disabled
    ApRole                      :  MeshAP
    ApBackhaul                  :  802.11a
    ApBackhaulChannel           :  0
    ApBackhaulSlot              :  2
    ApBackhaul11gEnabled        :  0
    ApBackhaulTxRate            :  24000
    Ethernet Bridging State     :  0
    Public Safety State         :  disabled
    AP Rogue Detection Mode     :  Enabled
    AP Tcp Mss Adjust           :  Disabled
    AP IPv6 TCP MSS Adjust      :  Disabled
    Predownload Status          :  None
    Auto Immune Status          :  Disabled
    RA Guard Status             :  Disabled
    Efficient Upgrade State     :  Disabled
    Efficient Upgrade Role      :  None
    TFTP Server                 :  Disabled
    Antenna Band Mode           :  Unknown
    802.11bg(0) Radio
    ADMIN  State =  ENABLE [1]
    OPER   State =    DOWN [1]
    CONFIG State =      UP [2]
    HW     State =      UP [4]
      Radio Mode                : Bridge
      GPR Period                : 0
      Beacon Period             : 0
      DTIM Period               : 0
      World Mode                : 1
      VoceraFix                 : 0
      Dfs peakdetect            : 1
      Fragmentation Threshold   : 2346
      Current Tx Power Level    : 0
      Current Channel           : 11
      Current Bandwidth         : 20
    802.11a(1) Radio
    ADMIN  State =  ENABLE [1]
    OPER   State =    DOWN [1]
    CONFIG State =      UP [2]
    HW     State =      UP [4]
      Radio Mode                : Bridge
      GPR Period                : 0
      Beacon Period             : 0
      DTIM Period               : 0
      World Mode                : 1
      VoceraFix                 : 0
      Dfs peakdetect            : 1
      Fragmentation Threshold   : 2346
      Current Tx Power Level    : 1
      Current Channel           : 165
      Current Bandwidth         : 20
    It is showing the following error on our WLC in the log file:
    Tue Jul 15 14:01:26 2014
    AAA Authentication Failure for UserName:88f042907184 User Type: WLAN USER
    And here are some of the errors it's showing on the AP after bootup:
    *Jul 15 17:47:30.471: %CAPWAP-5-SENDJOIN: sending Join Request to x.x.x.x
    *Jul 15 17:47:31.003: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Jul 15 17:47:31.031: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Jul 15 17:47:31.039: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    *Jul 15 17:47:31.047: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Jul 15 17:47:32.067: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Jul 15 17:47:33.067: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Jul 15 17:47:35.471: %CAPWAP-5-SENDJOIN: sending Join Request to x.x.x.x
    *Jul 15 17:47:35.471: %DTLS-5-ALERT: Received WARNING : Close notify alert from x.x.x.x
    *Jul 15 17:47:35.475: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    *Jul 15 17:47:35.483: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Jul 15 17:47:36.475: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Jul 15 17:47:36.503: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Jul 15 17:47:37.503: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Jul 15 17:48:15.007: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
    *Jul 15 17:48:15.007: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
    *Jul 15 17:48:15.007: %MESH-6-LINK_UPDOWN: Mesh station 88f0.4290.7184 link Down
    *Jul 15 17:48:17.007: %LINK-6-UPDOWN: Interface BVI1, changed state to down
    *Jul 15 17:48:22.507: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
    *Jul 15 17:59:10.099: %CAPWAP-3-ERRORLOG: Invalid event 31 & state 4 combination
    *Jul 15 17:59:10.099: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message. Event 31, state 4

  • Cisco 5508-WLC using MS NPS as RADIUS Server for EAP-TLS

    Has anyone experienced a problem getting a Cisco WLC to work with MS NPS server? We've done it before albeit with differnt code versions.
    I have a Cisco 5508 WLC running 7.0.116.0 code hosting a WLAN configured for WPA2 with 802.1x for authentication.  I have two Windows NPS servers configured as the RADIUS servers for EAP-TLS authentication. Via debug info on the WLC I can see the 802.1x handshake take place with the wireless client and the WLC as well as a successful transmission of an Authentication Packet from the WLC to one of the RADIUS servers. However on the WLC I see repeated RADIUS server x.x.x.x:1812 deactivated in global list and on the NPS server I'm seeing event log errors indicating "The Network Policy Server discarded the request for a user"  along with the pertinent auth request info that I would expect the NPS server to receive from the WLC.
    Based on the WLC debug info I'm never actually getting to the EAP-TLS certificate authentication part. It seems the NPS servers don't like the format of the initial RADIUS authentication request coming from the WLC and so don't respond whcih in turn casues to WLC to switch to the other NPS server which produces the same issue.
    Any ideas of what might be the issue or misconfiguration?

    Jim,
    I wanted to know if you can setup wireshark on both of the boxes and see if your are hitting the following bug:
    http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCti91044
    It looks as if the WLC is retransmitting the client traffic from one radius session with primary over to the secondary in which the radius state attribute that was assigned from the primary server is probably hitting the secondary server. Therefore if the state attribute isnt assigned from the secondary server it will discard the packet.
    May need to open a TAC case to see if this issue is on the 550x controllers also.
    Thanks,
    Tarik

  • 5508 WLC upgrade

    Looking to upgrade our 5508 WLC to the newest code AIR-CT5500-K9-7-2-103-0-FUS
    We are currently running an older code  6.0.196.0
    Are there any issues that I need to worry about with this upgrade ?
    Do I need to upgrade the AP's at the same time ?
    Any help would be appreciated.
    Cheers
    Dave

    Looking to upgrade our 5508 WLC to the newest code AIR-CT5500-K9-7-2-103-0-FUS
    Is the WLC going to be used in RUSSIA?  That's what this code is for.  If not, use the "AIR-CT5500-K9-7-2-103-0.aes" file instead.
    Do I need to upgrade the AP's at the same time ?
    The WLC will do it for you.

  • 5508 WLC HA pair - change management interface settings

    Hi,
    We have a pair of 5508 WLC's in a HA configuration that is working well at the moment, however I have noticed that the management interface is configured as untagged. I would like to change this to tagged and change the attached switch to trunk for these devices but if I try and edit the management interface through the GUI the VLAN and IP address section is greyed out and cannot be changed. While I could attempt it through the CLI and am comfortable doing that, the fact that it cannot be changed through the GUI implies that this should not be changed and so I am after further information. I don't have any lab equipment other than the HA pair in production so I cannot try changing it through the CLI at the moment. 
    The WLC's are in LAG mode if that makes any difference. I realise there may be downtime required for making this change but I am trying to work out the steps to get this done without having to drastically reconfigure things. 
    Any assistance would be appreciated. 

    Introduction of New Interfaces for HA Interaction
    Redundancy Management Interface
    The IP address on this interface should be configured in the same subnet as the management interface. This interface will check the health of the Active WLC via network infrastructure once the Active WLC does not respond to Keepalive messages on the Redundant Port. This provides an additional health check of the network and Active WLC, and confirms if switchover should or should not be executed. Also, the Standby WLC uses this interface in order to source ICMP ping packets to check gateway reachability. This interface is also used in order to send notifications from the Active WLC to the Standby WLC in the event of Box failure or Manual Reset. The Standby WLC will use this interface in order to communicate to Syslog, the NTP server, and the TFTP server for any configuration upload.
    Redundancy Port
    This interface has a very important role in the new HA architecture. Bulk configuration during boot up and incremental configuration are synced from the Active WLC to the Standby WLC using the Redundant Port. WLCs in a HA setup will use this port to perform HA role negotiation. The Redundancy Port is also used in order to check peer reachability sending UDP keep-alive messages every 100 msec (default timer) from the Standby WLC to the Active WLC. Also, in the event of a box failure, the Active WLC will send notification to the Standby WLC via the Redundant Port. If the NTP server is not configured, a manual time sync is performed from the Active WLC to the Standby WLC on the Redundant Port. This port in case of standalone controller and redundancy VLAN in case of WISM-2 will be assigned an auto generated IP Address where last 2 octets are picked from the last 2 octets of Redundancy Management Interface (the first 2 octets are always 169.254).

  • WLC redundancy with prime

    Hi all,
    We are going to implement high availabilty in 5508 WLC with version of 7.3.101 . We will be using Prime infrastructure 1.2 for monitoring purpose.
    With Prime , whether we can monitor and manage redundant WLC also or only active WLC?...
    Thanks for your help.......

    I just know from experience. You can only GUI/ssh into the primary WLC when you enable AP-SSO. So once the pairs are in HA, that is it.... You have only the primary WLC IP address available. You learn things the hard way sometimes because there are things not documented.
    Sent from Cisco Technical Support iPhone App

  • WLC Redundancy Question

    Hi Community,
    I have one question regarding the redundancy feature for two WLC 2106. We have installed on a customer site 2 WLC's 2106  and 6 AP's. Primary and Backup WLC works fine. No the customer asks the question if there is a option to copy the guest access wlan user from the primary controller to the backup controller? The lobby user activates a new user on the primary controller and if the primary controller fails, then the user did not get access to the wlan guest network.
    Any ideas?
    Thanks for help.
    Rene

    Hi Jerry,
    Mobility - it's used for client so that they can roam without any issue and one tunnle will be stablish between wlc-1 and wlc-2. if wlc-1 goes down the client will be local to the wlc-2 and if the guest user is not present on wlc-2 then it will not be able to access network.
    HA for AP - primary, secondary are used to achieve this.
    HA for WLC (WLC redundency) - suppose you have two WLCs if one goes down then second will start serving without any issue. For that master wlc will push all the config to second wlc and some other mechanism to achieve this. This functionality is not yet support.
    Thannks

  • WLC Redundancy over L3 link

    Hi All,
    Is it possible to deploy WLC redundancy over L3 link???
    In our scenario we have 2 controllers located in 2 different sites, the link between the site is L3. AP's are deployed across four other locations, two are coming to site 1 and rest two are coming to site 2 . How can i make redundancy on this setup , Please advice
    Controller is 4404 and AP's are 1231G series .
    Regards
    Aslam ...

    What is your link between each site? Also, I suppose your ap's are running in H-REAP mode? If you don't have enough bandwidth, then you shouldn't try it. You can always try to move the ap's to either wlc and see if users have any issues or not, before you try to deploy redundancy in this matter.

  • Can't put two 5508 WLCs in the same RF group

    Hi experts,
    I have two 5508 WLCs and I want them to be backup to each other. I put in the same "RF Group Name" and even the same "Default Mobility Domain Name" however under Wireless -> 802.11b/g/n -> RRM -> RF Grouping each controller still only have themselves as the only memter to the group.
    Two controllers are having management IPs on the same subnet 192.168.161.x/24. AP-manager interfaces are in the same network as well. They can ping each other fine. The following screen shots show the current relavent config on the controller:
    I do have two controllers in the same mobility group and they are both showing up...
    Does anyone know why they can't add each other to the RF group? All other settings are pretty much default...
    Thanks!

    Hi,
    is there a chance that one of the 2 WLC doesn't contain any access point ? Or that the APs from one WLC are not physically close to the APs of the second WLC ?
    The point of RF grouping is to exchange RF information, to make RRM decisions together and to know what ap is a rogue and which is not. RF group information travels over the air from AP to AP.
    So if a wlc has no ap of if its APs are not close to those of the other WLC there is both no point in grouping with the other WLC in rf group and also no technical way of doing so.
    Regards,
    Nicolas
    ===
    Don't forget to rate answers that you find useful

  • Can't get 1532i to associate to 5508 WLC running 7.6.130.0

    Greetings,
    I've got 20 or so APs on a 5508 WLC.  Most of the APs are 1242, one is 3602.  I'm now trying to get a 1532i to associate to the 5508 and it's not happening.  This is the first 1532 on this controller.
    Also, I got this 1532 AP from a sister site and they had it configured as Autonomous in wgb mode, so I had to do the Autonomous to Unified Conversion.  This conversion appeared to go successfully.  But now the AP won't associate to my controller. 
    Thanks
    Following is what happens from the AP's console :
    AP78da.6e59.e58a#reload
    Proceed with reload? [confirm]
    Writing out the event log to flash:/event.log ...
    Write of event.log done
    *Oct 28 20:27:37.151: %SYS-5-RELOAD: Reload requested by Cisco on console. Reload Reason: Reload.
    *Oct 28 20:27:37.155: %LWAPP-5-CHANGED: CAPWAP changed state to DOWN
                                                                        *Oct 28 20:27:39.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.132.249.5:5246
    *Oct 28 20:27:40.039: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    System Bootstrap, Version U-Boot 1.1.4-gf5ee82b1-dirty Corfu , RELEASE SOFTWARE
    Build Date: Oct 17 2013 - 18:08:55
    corfu - Scorpion 1.0
    DRAM:  256 MB
    Now running in RAM - U-Boot at: 8ffbc000
    Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x14
    flash size 1MB, sector count = 256
    Atheros on-chip NAND FLash Controller Driver, Version 0.1 (c) 2010 Atheros Communications, Ltd.
    Ath Nand ID[8ffee17c]: 2c:f1:80:95:02
    ONFI MICRON      MT29F1G08ABADAWP
    Micron NAND 128MiB 3,3V 8-bit [128MB]
    size = 128MB
    Hit any key to stop autoboot:  0
    boot_method is set to IOS_BOOT, boot IOS bootloader in NOR flash
    Loading .text @ 0x84000000 (207840 bytes)
    Loading .rodata @ 0x84032be0 (39008 bytes)
    Loading .data @ 0x8403c440 (3264 bytes)
    Loading .data.rel.local @ 0x8403d100 (1084 bytes)
    Loading .data.rel @ 0x8403d53c (124 bytes)
    Loading .data.rel.ro @ 0x8403d5b8 (960 bytes)
    Clearing .bss @ 0x8403d980 (161116 bytes)
    Clearing .scommon @ 0x84064edc (56 bytes)
    ## Starting application at 0x84000000 ...
    IOS Secondary Bootloader - Starting system.HW Test Status(0)
    Ath Nand ID: 95:80:f1:2c:00
    Using driver version 1 for media type 2
    Valid buffers 146
    total146  146
    success found all blocks
    start end 65 85
    found in range
    high low end 2728 2089 85
    Xmodem file system is available.
    mifs[0]: 15 files, 5 directories
    mifs[0]: Total bytes     :  131334144
    mifs[0]: Bytes used      :    7966720
    mifs[0]: Bytes available :  123367424
    mifs[0]: mifs fsck took 0 seconds.
    Base Ethernet MAC address: 78:da:6e:59:e5:8a
    Setup MAC....
    Waiting for PHY auto negotiation to complete...Port 0 Negogiation success.
    Ethernet speed is 100 Mb - FULL duplex
    Scorpion  ----> F1 PHY *
    : cfg1 0xf cfg2 0x7115
    Loading "flash:/ap1g3-k9w8-mx.152-4.JB6/ap1g3-k9w8-mx.152-4.JB6"...##########################################################################################################################################################################################################################################################################################################################################################################
    File "flash:/ap1g3-k9w8-mx.152-4.JB6/ap1g3-k9w8-mx.152-4.JB6" uncompressed and installed, entry point: 0x60080000
    executing...
    Stop MAC.
    Starting IOS...
    cp0 timer begin value is set as 1000
    prid= 19750
    Starts main.
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C1530 Software (ap1g3-K9W8-M), Version 15.2(4)JB6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 22-Aug-14 11:03 by prod_rel_team
    Initializing flashfs...
    Ath Nand ID: 95:80:F1:2C:00
    Using driver version 1 for media type 2
    Valid buffers 146
    total146  146
    success found all blocks
    start end 65 85
    found in range
    high low end 2728 2089 85
    mifs[4]: 15 files, 5 directories
    mifs[4]: Total bytes     : 131334144
    mifs[4]: Bytes used      : 7966720
    mifs[4]: Bytes available : 123367424
    mifs[4]: mifs fsck took 2 seconds.
    mifs[4]: Initialization complete.
    ...done Initializing flashfs.
    :pci_init_board:521 *** Warning *** : PCIe1 WLAN Module not found !!!
    pci_rc2_init_board:570 PCIE Controller Init Bus Master Enable
    :pci_rc2_init_board:593 PCIe2 WLAN Module Found !!!
    soap_pci_subsys_init:706 Bus Master/Mem Enable on pci_write side
    soap_pci_subsys_init(713): PCI vendor ID: 0x168C ret:0
    soap_pci_subsys_init(715): PCI device ID: 0x33 ret:0
    Scorpion  ----> F1 PHY *
    Waiting for PHY auto negotiation to complete...Port 0 Negogiation success.
    Disabling 802.3az feature on port 0
    sgmii cal value = 0xE
    Disabling 802.3az feature on port 1.
    SGMII setup done, status is 0x2
    Radio0  present 9550 9000 0 0 0 0
    Rate table has 282 entries (12 legacy/96 11n/174 11ac)
    Radio1  present 9590 9000 0 0 B2000000 1
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP1532I-A-K9 (MIPS74k) processor (revision 27) with 204800K/57344K bytes of memory.
    Processor board ID FTX1813201L
    MIPS74k CPU at 700MHz, revision number 0x0000
    Last reset from power-on
    LWAPP image version 7.6.100.0
    2 Gigabit Ethernet interfaces
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 78:DA:6E:59:E5:8A
    Part Number                          : 74-11942-01
    PCA Assembly Number                  : 000-00000-00
    PCA Revision Number                  :
    PCB Serial Number                    : FOC180951ZR
    Top Assembly Part Number             : 000-00000-00
    Top Assembly Serial Number           : FTX1813201L
    Top Revision Number                  : 23
    Product/Model Number                 : AIR-CAP1532I-A-K9
    % Please define a domain-name first.
    Press RETURN to get started!
    *Mar  1 00:00:09.895: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (11)mips74k_config_radio_pci(302): PCI CMD write: 0x356
    *Mar  1 00:00:14.391: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to upEnterprise mode: 0x44000000
    *Mar  1 00:00:14.895: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (2)
    *Mar  1 00:00:14.971: ath_load_ctl_pwr_tbl() dot11radio 2G loading CTL binary flash:/ap1g3-k9w8-mx.152-4.JB6/CO2.bin version# 3.0
    *Mar  1 00:00:15.419: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (2)
    *Mar  1 00:00:15.419: ath_load_ctl_pwr_tbl() dot11radio 5G loading CTL binary flash:/ap1g3-k9w8-mx.152-4.JB6/CO5.bin version# 3.4
    *Mar  1 00:00:15.699: CDP_PD: Power Source: 4-pair Power Injector
    *Mar  1 00:00:15.723: AP Mesh platform identified (backhaul config:0x2, access:0xF)
    *Mar  1 00:00:15.735: Starting Ethernet promiscuous mode
    *Mar  1 00:00:15.735: Skipping Ethernet bridge initializaion
    *Mar  1 00:00:16.431: %LINK-6-UPDOWN: Interface GigabitEthernet1, changed state to up
    *Mar  1 00:00:18.363: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1530 Software (ap1g3-K9W8-M), Version 15.2(4)JB6, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 22-Aug-14 11:03 by prod_rel_team
    *Mar  1 00:00:18.363: %SNMP-5-COLDSTART: SNMP agent on host AP78da.6e59.e58a is undergoing a cold start
    *Mar  1 00:00:18.399: %MESH-6-BVI_CREATED: Mesh BVI1 interface created
    *Mar  1 00:00:18.399: ath_ACIF_set_distance: Retrieved existing timeout value: 25us for distance: 0km
    *Mar  1 00:00:18.399: ath_ACIF_set_distance: Setting new timeout value: 45us for distance: 3km
    *Mar  1 00:00:18.399: %CDP_PD-4-POWER_OK: Full power - HIGH_POWER inline power source
    *Mar  1 00:00:18.619: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:18.619: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:18.619: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
    *Mar  1 00:00:18.811: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:20.399: %LINK-6-UPDOWN: Interface BVI1, changed state to down
    *Mar  1 00:00:37.015: Logging LWAPP message to 255.255.255.255.
    *Mar  1 00:00:37.027: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:00:38.027: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:38.035: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:00:39.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:39.067: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:40.023: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
    *Mar  1 00:00:40.067: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Mar  1 00:01:13.531:  Mesh setting the ethernet port 0 state to 2
    *Mar  1 00:01:13.531: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:01:15.531: %LINK-6-UPDOWN: Interface BVI1, changed state to up
    *Mar  1 00:01:16.531: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:01:18.639: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    *Mar  1 00:01:18.651: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:01:19.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:01:19.671: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:01:20.671: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:01:28.643: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:01:28.759: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.132.120.85, mask 255.255.255.0, hostname AP78da.6e59.e58a
    *Mar  1 00:01:28.759: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:01:33.791: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Mar  1 00:01:33.855: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    Translating "CISCO-CAPWAP-CONTROLLER.americas.mittalco.com"...domain server (10.132.250.250) [OK]
    *Mar  1 00:01:33.867: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:01:34.855: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Mar  1 00:01:34.855: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:01:34.915: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:01:35.915: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:01:44.855: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Oct 28 20:29:44.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.132.249.5 peer_port: 5246
    *Oct 28 20:29:44.495: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.132.249.5 peer_port: 5246
    *Oct 28 20:29:44.495: %CAPWAP-5-SENDJOIN: sending Join Request to 10.132.249.5
    *Oct 28 20:29:44.499: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
    *Oct 28 20:29:44.499: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
    *Oct 28 20:29:44.499: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Oct 28 20:29:44.499: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.132.249.5
    *Oct 28 20:29:49.495: %CAPWAP-5-SENDJOIN: sending Join Request to 10.132.249.5
    *Oct 28 20:30:43.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.132.249.5:5246
    *Oct 28 20:30:44.031: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Oct 28 20:30:44.095: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    *Oct 28 20:30:44.135: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Oct 28 20:30:45.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Oct 28 20:30:45.155: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Oct 28 20:30:46.155: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Oct 28 20:30:54.095: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Oct 28 20:30:52.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.132.249.5 peer_port: 5246
    *Oct 28 20:30:52.499: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.132.249.5 peer_port: 5246
    *Oct 28 20:30:52.499: %CAPWAP-5-SENDJOIN: sending Join Request to 10.132.249.5
    *Oct 28 20:30:52.499: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
    *Oct 28 20:30:52.503: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
    *Oct 28 20:30:52.503: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Oct 28 20:30:52.503: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.132.249.5
    *Oct 28 20:30:57.499: %CAPWAP-5-SENDJOIN: sending Join Request to 10.132.249.5

    You have to add the MAC address of the 1530 to the WLC mac filter list before the AP will join. Here is a link that explains it. 
    http://www.cisco.com/c/en/us/td/docs/wireless/access_point/1530/quick/guide/ap1532qsg.html#pgfId-45801
    Scott

  • How can I add the new AP license to HA 5508 WLC?

    Hi,
    My customer has two 5508 WLC in HA mode and these devices have 250 AP license. Customer bought 50 AP and 50 AP license. But I could not add the license to WLC! When I check the Management>Software Activation> tab there are only two options under the tab these are "Licenses" "License Usage". There is no "Command" option in there. Also I tried add on CLI but this error log appeared " !!!! Blocked: Changing License configurations on Secondary unit is blocked !!!! " 
    I think this is possible when disable the HA but is there anybody know this how can I add the new 50 AP license to HA WLC without disable the HA?
    Thanks,
    Burhan

    Hi,
    Thank you for your reply. 
    Yes I know the controllers synchronize with the enabled license and the 250 AP license bundled with two device there is no problem.
    I want to add new 50 AP license in addition 250 AP license. Because customer has 300 AP's.
    As I said, When I check the Management>Software Activation> tab there are only two options under the tab these are "Licenses" "License Usage". There is no "Command" option in there.
    Thanks,

  • Can we use a 5508 WLC in Hong Kong and join 3602 APs in Vietnam to it? Any regulatory contraints?

    Hi friends,
    I am looking for some wisdom here!
    Just wondering if I can use a 5508 WLC in Hong Kong and join 3602 APs in Vietnam to it?
    Any regulatory contsraints / guidelines that would prohibit from doing so?
    - Regards,
    Tarun.

    You have two differnt regulations... here is a link:
    http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd80537b6a_ps10981_Products_Data_Sheet.html
    You need to make sure you are not breaking any rules and it is best to have an AP that is specific to that country.  Also if you add multiple country codes on a WLC, the AP's will only be able to use the most common channels and TX power setting allowed on both.  Here is a link explaining that.
    http://nostringsattachedshow.com/2012/02/02/multiple-country-codes-with-the-cisco-wlc/
    Thanks,
    Scott
    Help out other by using the rating system and marking answered questions as "Answered"

  • 5508 WLC - 7.0.98.218 - Local users password reset

    We are required to change passwords every so often at my job. I am trying to change the password  for one of the local user accounts on a  5508 WLC running 7.0.98.218 -  How can I accomplish this task? The option  I get is to remove the users. Any help would be much appriciated.
    Thanks,
    marramix01

    Hi,
    I think ur speaking about LOCAL NET USERs list on the WLC..
    I am able to change that on my WLC..
    its .. WLC GUI >> SECURITY >> LOCAL NET USERS >> Client on the local user >> Edit it >> Apply.
    Clisk on the name which is under USERNAME and u wil be able to edit it!!
    Lemme know if this helps and please dont forget to rate the usefull posts!!
    Regards
    Surendra

  • 5508 wlc with 1140 APs and NPS cant connect

    Hi.. let me go off with the equipment setup that I have first..
    I have 3 sites each site has  2x 5508 WLC and a few 1140 AP's per site.
    I also have 3 NPS running on those 3 sites..
    I have NPS and dhcp running on the same server...
    I have a seperate CA root Authority server.
    3 seperate DC ... one per site..
    I followed everything accoriding to  this guide
    http://araihan.wordpress.com/2010/04/30/complete-guide-to-build-a-cisco-wireless-infrastructure-using-cisco-wlc-5500-cisco-1142-ap-and-microsoft-radius-server/
    and also the guide that is on the CISCO site
    http://www.cisco.com/en/US/products/ps10315/products_configuration_example09186a0080bfb19a.shtml
    I did a debug on the wlc for the wireless client that I was using to try and connect.. I get the following   I hope someone can help me figure out whats wrong.
    =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.09.18 13:50:17 =~=~=~=~=~=~=~=~=~=~=~=
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:40.000: 00:14:a5:4b:cf:ef Received EAPOL START from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:40.000: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Aborting state
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:40.001: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:40.001: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 4)
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:40.001: 00:14:a5:4b:cf:ef Reached Max EAP-Identity Request retries (3) for STA 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:40.003: 00:14:a5:4b:cf:ef Sent Deauthenticate to mobile on BSSID 24:01:c7:ed:48:70 slot 0(caller 1x_auth_pae.c:3241)
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:40.003: 00:14:a5:4b:cf:ef Scheduling deletion of Mobile Station:  (callerId: 6) in 10 seconds
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:40.003: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Disconnected state
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:40.003: 00:14:a5:4b:cf:ef Not sending EAP-Failure for STA 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:52:40.004: Stats update: Non Zero value
    *apfMsConnTask_7: Sep 18 13:52:42.098: Stats update: Non Zero value
    *apfMsConnTask_7: Sep 18 13:52:42.101: Stats update: Non Zero value
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef Reassociation received from mobile on BSSID 24:01:c7:ed:48:72
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef Global 200 Clients are allowed to AP radio
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef Rf profile 200 Clients are allowed to AP wlan
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef In processSsidIE:4202 setting Central switched to TRUE
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef In processSsidIE:4205 apVapId = 3 and Split Acl Id = 65535
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef Applying site-specific Local Bridging override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef Applying Local Bridging Interface Policy for station 00:14:a5:4b:cf:ef - vlan 232, interface id 13, interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef Applying site-specific override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_7: Sep 18 13:52:42.102: 00:14:a5:4b:cf:ef processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef STA - rates (8): 130 132 139 150 36 48 72 108 12 18 24 96 0 0 0 0
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef STA - rates (12): 130 132 139 150 36 48 72 108 12 18 24 96 0 0 0 0
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef Processing RSN IE type 48, length 20 for mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef Received RSN IE with 0 PMKIDs from mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef Setting active key cache index 8 ---> 8
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef unsetting PmkIdValidatedByAp
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Initializing policy
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 24:01:c7:ed:48:70 vapId 3 apVapId 3 flex-acl-name:
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef apfPemAddUser2 (apf_policy.c:276) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Associated to Associated
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef apfPemAddUser2:session timeout forstation 00:14:a5:4b:cf:ef - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is  0
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef Sending Assoc Response to station on BSSID 24:01:c7:ed:48:72 (status 0) ApVapId 3 Slot 0
    *apfMsConnTask_7: Sep 18 13:52:42.103: 00:14:a5:4b:cf:ef apfProcessAssocReq (apf_80211.c:7391) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Associated to Associated
    *dot1xMsgTask: Sep 18 13:52:42.108: 00:14:a5:4b:cf:ef Station 00:14:a5:4b:cf:ef setting dot1x reauth timeout = 1800
    *dot1xMsgTask: Sep 18 13:52:42.108: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *dot1xMsgTask: Sep 18 13:52:42.108: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 1)
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:42.133: 00:14:a5:4b:cf:ef Received EAPOL START from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:42.133: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:42.133: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 2)
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:42.150: 00:14:a5:4b:cf:ef Received EAPOL EAPPKT from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:42.150: 00:14:a5:4b:cf:ef Received EAP Response packet with mismatching id (currentid=2, eapid=1) from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:42.165: 00:14:a5:4b:cf:ef Received EAPOL EAPPKT from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:42.165: 00:14:a5:4b:cf:ef Received Identity Response (count=2) from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:42.165: 00:14:a5:4b:cf:ef EAP State update from Connecting to Authenticating for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:42.165: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Authenticating state
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:42.165: 00:14:a5:4b:cf:ef Entering Backend Auth Response state for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:42.172: 00:14:a5:4b:cf:ef Processing Access-Reject for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:42.173: 00:14:a5:4b:cf:ef Removing PMK cache due to EAP-Failure for mobile 00:14:a5:4b:cf:ef (EAP Id -1)
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:42.173: 00:14:a5:4b:cf:ef Sending EAP-Failure to mobile 00:14:a5:4b:cf:ef (EAP Id -1)
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:42.173: 00:14:a5:4b:cf:ef Entering Backend Auth Failure state (id=-1) for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:42.173: 00:14:a5:4b:cf:ef Setting quiet timer for 5 seconds for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:42.173: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Unknown state
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:42.211: 00:14:a5:4b:cf:ef Received EAPOL START from mobile 00:14:a5:4b:cf:ef
    *osapiBsnTimer: Sep 18 13:52:47.076: 00:14:a5:4b:cf:ef 802.1x 'quiteWhile' Timer expired for station 00:14:a5:4b:cf:ef and for message = M0
    *dot1xMsgTask: Sep 18 13:52:47.076: 00:14:a5:4b:cf:ef quiet timer completed for mobile 00:14:a5:4b:cf:ef
    *dot1xMsgTask: Sep 18 13:52:47.076: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *dot1xMsgTask: Sep 18 13:52:47.076: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 1)
    *apfMsConnTask_7: Sep 18 13:52:55.606: Stats update: Non Zero value
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:59.228: 00:14:a5:4b:cf:ef Received EAPOL EAPPKT from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:59.228: 00:14:a5:4b:cf:ef Received Identity Response (count=3) from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:59.228: 00:14:a5:4b:cf:ef Reached Max EAP-Identity Request retries (3) for STA 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:59.231: 00:14:a5:4b:cf:ef Sent Deauthenticate to mobile on BSSID 24:01:c7:ed:48:70 slot 0(caller 1x_auth_pae.c:3241)
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:59.231: 00:14:a5:4b:cf:ef Scheduling deletion of Mobile Station:  (callerId: 6) in 10 seconds
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:59.231: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Disconnected state
    *Dot1x_NW_MsgTask_7: Sep 18 13:52:59.231: 00:14:a5:4b:cf:ef Not sending EAP-Failure for STA 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:52:59.231: Stats update: Non Zero value
    *apfMsConnTask_7: Sep 18 13:53:01.348: Stats update: Non Zero value
    *apfMsConnTask_7: Sep 18 13:53:01.351: Stats update: Non Zero value
    *apfMsConnTask_7: Sep 18 13:53:01.351: 00:14:a5:4b:cf:ef Reassociation received from mobile on BSSID 24:01:c7:ed:48:72
    *apfMsConnTask_7: Sep 18 13:53:01.351: 00:14:a5:4b:cf:ef Global 200 Clients are allowed to AP radio
    *apfMsConnTask_7: Sep 18 13:53:01.351: 00:14:a5:4b:cf:ef Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_7: Sep 18 13:53:01.351: 00:14:a5:4b:cf:ef Rf profile 200 Clients are allowed to AP wlan
    *apfMsConnTask_7: Sep 18 13:53:01.351: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *apfMsConnTask_7: Sep 18 13:53:01.351: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_7: Sep 18 13:53:01.351: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef In processSsidIE:4202 setting Central switched to TRUE
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef In processSsidIE:4205 apVapId = 3 and Split Acl Id = 65535
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef Applying site-specific Local Bridging override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef Applying Local Bridging Interface Policy for station 00:14:a5:4b:cf:ef - vlan 232, interface id 13, interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef Applying site-specific override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef STA - rates (8): 130 132 139 150 36 48 72 108 12 18 24 96 0 0 0 0
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef STA - rates (12): 130 132 139 150 36 48 72 108 12 18 24 96 0 0 0 0
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef Processing RSN IE type 48, length 20 for mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef Received RSN IE with 0 PMKIDs from mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef Setting active key cache index 8 ---> 8
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef unsetting PmkIdValidatedByAp
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Initializing policy
    *apfMsConnTask_7: Sep 18 13:53:01.352: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
    *apfMsConnTask_7: Sep 18 13:53:01.353: 00:14:a5:4b:cf:ef 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_7: Sep 18 13:53:01.353: 00:14:a5:4b:cf:ef Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_7: Sep 18 13:53:01.353: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 24:01:c7:ed:48:70 vapId 3 apVapId 3 flex-acl-name:
    *apfMsConnTask_7: Sep 18 13:53:01.353: 00:14:a5:4b:cf:ef apfPemAddUser2 (apf_policy.c:276) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Associated to Associated
    *apfMsConnTask_7: Sep 18 13:53:01.353: 00:14:a5:4b:cf:ef apfPemAddUser2:session timeout forstation 00:14:a5:4b:cf:ef - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is  0
    *apfMsConnTask_7: Sep 18 13:53:01.353: 00:14:a5:4b:cf:ef Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_7: Sep 18 13:53:01.353: 00:14:a5:4b:cf:ef Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
    *apfMsConnTask_7: Sep 18 13:53:01.353: 00:14:a5:4b:cf:ef Sending Assoc Response to station on BSSID 24:01:c7:ed:48:72 (status 0) ApVapId 3 Slot 0
    *apfMsConnTask_7: Sep 18 13:53:01.353: 00:14:a5:4b:cf:ef apfProcessAssocReq (apf_80211.c:7391) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Associated to Associated
    *dot1xMsgTask: Sep 18 13:53:01.356: 00:14:a5:4b:cf:ef Station 00:14:a5:4b:cf:ef setting dot1x reauth timeout = 1800
    *dot1xMsgTask: Sep 18 13:53:01.356: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *dot1xMsgTask: Sep 18 13:53:01.356: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 1)
    *Dot1x_NW_MsgTask_7: Sep 18 13:53:01.401: 00:14:a5:4b:cf:ef Received EAPOL START from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:53:01.401: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *Dot1x_NW_MsgTask_7: Sep 18 13:53:01.401: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 2)
    *osapiBsnTimer: Sep 18 13:53:31.276: 00:14:a5:4b:cf:ef 802.1x 'txWhen' Timer expired for station 00:14:a5:4b:cf:ef and for message = M0
    *dot1xMsgTask: Sep 18 13:53:31.276: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *dot1xMsgTask: Sep 18 13:53:31.276: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 3)
    *osapiBsnTimer: Sep 18 13:54:01.276: 00:14:a5:4b:cf:ef 802.1x 'txWhen' Timer expired for station 00:14:a5:4b:cf:ef and for message = M0
    *dot1xMsgTask: Sep 18 13:54:01.276: 00:14:a5:4b:cf:ef Reached Max EAP-Identity Request retries (3) for STA 00:14:a5:4b:cf:ef
    *dot1xMsgTask: Sep 18 13:54:01.279: 00:14:a5:4b:cf:ef Sent Deauthenticate to mobile on BSSID 24:01:c7:ed:48:70 slot 0(caller 1x_auth_pae.c:3241)
    *dot1xMsgTask: Sep 18 13:54:01.279: 00:14:a5:4b:cf:ef Scheduling deletion of Mobile Station:  (callerId: 6) in 10 seconds
    *dot1xMsgTask: Sep 18 13:54:01.279: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Disconnected state
    *dot1xMsgTask: Sep 18 13:54:01.279: 00:14:a5:4b:cf:ef Not sending EAP-Failure for STA 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:54:01.280: Stats update: Non Zero value
    *apfMsConnTask_7: Sep 18 13:54:03.414: Stats update: Non Zero value
    *apfMsConnTask_7: Sep 18 13:54:03.417: Stats update: Non Zero value
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef Reassociation received from mobile on BSSID 24:01:c7:ed:48:72
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef Global 200 Clients are allowed to AP radio
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef Rf profile 200 Clients are allowed to AP wlan
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef In processSsidIE:4202 setting Central switched to TRUE
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef In processSsidIE:4205 apVapId = 3 and Split Acl Id = 65535
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef Applying site-specific Local Bridging override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef Applying Local Bridging Interface Policy for station 00:14:a5:4b:cf:ef - vlan 232, interface id 13, interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef Applying site-specific override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef STA - rates (8): 130 132 139 150 36 48 72 108 12 18 24 96 0 0 0 0
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef STA - rates (12): 130 132 139 150 36 48 72 108 12 18 24 96 0 0 0 0
    *apfMsConnTask_7: Sep 18 13:54:03.418: 00:14:a5:4b:cf:ef extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_7: Sep 18 13:54:03.419: 00:14:a5:4b:cf:ef Processing RSN IE type 48, length 20 for mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:54:03.419: 00:14:a5:4b:cf:ef Received RSN IE with 0 PMKIDs from mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:54:03.419: 00:14:a5:4b:cf:ef Setting active key cache index 8 ---> 8
    *apfMsConnTask_7: Sep 18 13:54:03.419: 00:14:a5:4b:cf:ef unsetting PmkIdValidatedByAp
    *apfMsConnTask_7: Sep 18 13:54:03.419: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Initializing policy
    *apfMsConnTask_7: Sep 18 13:54:03.419: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
    *apfMsConnTask_7: Sep 18 13:54:03.419: 00:14:a5:4b:cf:ef 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_7: Sep 18 13:54:03.419: 00:14:a5:4b:cf:ef Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_7: Sep 18 13:54:03.419: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 24:01:c7:ed:48:70 vapId 3 apVapId 3 flex-acl-name:
    *apfMsConnTask_7: Sep 18 13:54:03.419: 00:14:a5:4b:cf:ef apfPemAddUser2 (apf_policy.c:276) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Associated to Associated
    *apfMsConnTask_7: Sep 18 13:54:03.419: 00:14:a5:4b:cf:ef apfPemAddUser2:session timeout forstation 00:14:a5:4b:cf:ef - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is  0
    *apfMsConnTask_7: Sep 18 13:54:03.419: 00:14:a5:4b:cf:ef Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_7: Sep 18 13:54:03.419: 00:14:a5:4b:cf:ef Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
    *apfMsConnTask_7: Sep 18 13:54:03.419: 00:14:a5:4b:cf:ef Sending Assoc Response to station on BSSID 24:01:c7:ed:48:72 (status 0) ApVapId 3 Slot 0
    *apfMsConnTask_7: Sep 18 13:54:03.419: 00:14:a5:4b:cf:ef apfProcessAssocReq (apf_80211.c:7391) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Associated to Associated
    *dot1xMsgTask: Sep 18 13:54:03.421: 00:14:a5:4b:cf:ef Station 00:14:a5:4b:cf:ef setting dot1x reauth timeout = 1800
    *dot1xMsgTask: Sep 18 13:54:03.421: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *dot1xMsgTask: Sep 18 13:54:03.421: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 1)
    *Dot1x_NW_MsgTask_7: Sep 18 13:54:03.465: 00:14:a5:4b:cf:ef Received EAPOL START from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:54:03.465: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *Dot1x_NW_MsgTask_7: Sep 18 13:54:03.465: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 2)
    *apfMsConnTask_7: Sep 18 13:54:26.151: Stats update: Non Zero value
    *osapiBsnTimer: Sep 18 13:54:33.276: 00:14:a5:4b:cf:ef 802.1x 'txWhen' Timer expired for station 00:14:a5:4b:cf:ef and for message = M0
    *dot1xMsgTask: Sep 18 13:54:33.276: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *dot1xMsgTask: Sep 18 13:54:33.276: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 3)
    *osapiBsnTimer: Sep 18 13:55:03.276: 00:14:a5:4b:cf:ef 802.1x 'txWhen' Timer expired for station 00:14:a5:4b:cf:ef and for message = M0
    *dot1xMsgTask: Sep 18 13:55:03.276: 00:14:a5:4b:cf:ef Reached Max EAP-Identity Request retries (3) for STA 00:14:a5:4b:cf:ef
    *dot1xMsgTask: Sep 18 13:55:03.279: 00:14:a5:4b:cf:ef Sent Deauthenticate to mobile on BSSID 24:01:c7:ed:48:70 slot 0(caller 1x_auth_pae.c:3241)
    *dot1xMsgTask: Sep 18 13:55:03.279: 00:14:a5:4b:cf:ef Scheduling deletion of Mobile Station:  (callerId: 6) in 10 seconds
    *dot1xMsgTask: Sep 18 13:55:03.279: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Disconnected state
    *dot1xMsgTask: Sep 18 13:55:03.279: 00:14:a5:4b:cf:ef Not sending EAP-Failure for STA 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:55:05.371: 00:14:a5:4b:cf:ef Reassociation received from mobile on BSSID 24:01:c7:ed:48:72
    *apfMsConnTask_7: Sep 18 13:55:05.371: 00:14:a5:4b:cf:ef Global 200 Clients are allowed to AP radio
    *apfMsConnTask_7: Sep 18 13:55:05.371: 00:14:a5:4b:cf:ef Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_7: Sep 18 13:55:05.371: 00:14:a5:4b:cf:ef Rf profile 200 Clients are allowed to AP wlan
    *apfMsConnTask_7: Sep 18 13:55:05.371: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *apfMsConnTask_7: Sep 18 13:55:05.371: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_7: Sep 18 13:55:05.371: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_7: Sep 18 13:55:05.371: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_7: Sep 18 13:55:05.371: 00:14:a5:4b:cf:ef In processSsidIE:4202 setting Central switched to TRUE
    *apfMsConnTask_7: Sep 18 13:55:05.371: 00:14:a5:4b:cf:ef In processSsidIE:4205 apVapId = 3 and Split Acl Id = 65535
    *apfMsConnTask_7: Sep 18 13:55:05.371: 00:14:a5:4b:cf:ef Applying site-specific Local Bridging override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:55:05.371: 00:14:a5:4b:cf:ef Applying Local Bridging Interface Policy for station 00:14:a5:4b:cf:ef - vlan 232, interface id 13, interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:55:05.371: 00:14:a5:4b:cf:ef Applying site-specific override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:55:05.371: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *apfMsConnTask_7: Sep 18 13:55:05.371: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_7: Sep 18 13:55:05.371: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_7: Sep 18 13:55:05.372: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_7: Sep 18 13:55:05.372: 00:14:a5:4b:cf:ef processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_7: Sep 18 13:55:05.372: 00:14:a5:4b:cf:ef processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_7: Sep 18 13:55:05.372: 00:14:a5:4b:cf:ef STA - rates (8): 130 132 139 150 36 48 72 108 12 18 24 96 0 0 0 0
    *apfMsConnTask_7: Sep 18 13:55:05.372: 00:14:a5:4b:cf:ef suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_7: Sep 18 13:55:05.372: 00:14:a5:4b:cf:ef STA - rates (12): 130 132 139 150 36 48 72 108 12 18 24 96 0 0 0 0
    *apfMsConnTask_7: Sep 18 13:55:05.372: 00:14:a5:4b:cf:ef extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_7: Sep 18 13:55:05.372: 00:14:a5:4b:cf:ef Processing RSN IE type 48, length 20 for mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:55:05.372: 00:14:a5:4b:cf:ef Received RSN IE with 0 PMKIDs from mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:55:05.372: 00:14:a5:4b:cf:ef Setting active key cache index 8 ---> 8
    *apfMsConnTask_7: Sep 18 13:55:05.372: 00:14:a5:4b:cf:ef unsetting PmkIdValidatedByAp
    *apfMsConnTask_7: Sep 18 13:55:05.374: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Initializing policy
    *apfMsConnTask_7: Sep 18 13:55:05.374: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
    *apfMsConnTask_7: Sep 18 13:55:05.374: 00:14:a5:4b:cf:ef 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_7: Sep 18 13:55:05.374: 00:14:a5:4b:cf:ef Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_7: Sep 18 13:55:05.374: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 24:01:c7:ed:48:70 vapId 3 apVapId 3 flex-acl-name:
    *apfMsConnTask_7: Sep 18 13:55:05.374: 00:14:a5:4b:cf:ef apfPemAddUser2 (apf_policy.c:276) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Associated to Associated
    *apfMsConnTask_7: Sep 18 13:55:05.374: 00:14:a5:4b:cf:ef apfPemAddUser2:session timeout forstation 00:14:a5:4b:cf:ef - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is  0
    *apfMsConnTask_7: Sep 18 13:55:05.374: 00:14:a5:4b:cf:ef Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_7: Sep 18 13:55:05.374: 00:14:a5:4b:cf:ef Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
    *apfMsConnTask_7: Sep 18 13:55:05.374: 00:14:a5:4b:cf:ef Sending Assoc Response to station on BSSID 24:01:c7:ed:48:72 (status 0) ApVapId 3 Slot 0
    *apfMsConnTask_7: Sep 18 13:55:05.374: 00:14:a5:4b:cf:ef apfProcessAssocReq (apf_80211.c:7391) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Associated to Associated
    *dot1xMsgTask: Sep 18 13:55:05.376: 00:14:a5:4b:cf:ef Station 00:14:a5:4b:cf:ef setting dot1x reauth timeout = 1800
    *dot1xMsgTask: Sep 18 13:55:05.376: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *dot1xMsgTask: Sep 18 13:55:05.376: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 1)
    *Dot1x_NW_MsgTask_7: Sep 18 13:55:05.427: 00:14:a5:4b:cf:ef Received EAPOL START from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:55:05.428: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *Dot1x_NW_MsgTask_7: Sep 18 13:55:05.428: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 2)
    *osapiBsnTimer: Sep 18 13:55:35.276: 00:14:a5:4b:cf:ef 802.1x 'txWhen' Timer expired for station 00:14:a5:4b:cf:ef and for message = M0
    *dot1xMsgTask: Sep 18 13:55:35.276: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *dot1xMsgTask: Sep 18 13:55:35.276: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 3)
    *apfMsConnTask_7: Sep 18 13:55:56.698: Stats update: Non Zero value
    *osapiBsnTimer: Sep 18 13:56:05.276: 00:14:a5:4b:cf:ef 802.1x 'txWhen' Timer expired for station 00:14:a5:4b:cf:ef and for message = M0
    *dot1xMsgTask: Sep 18 13:56:05.276: 00:14:a5:4b:cf:ef Reached Max EAP-Identity Request retries (3) for STA 00:14:a5:4b:cf:ef
    *dot1xMsgTask: Sep 18 13:56:05.279: 00:14:a5:4b:cf:ef Sent Deauthenticate to mobile on BSSID 24:01:c7:ed:48:70 slot 0(caller 1x_auth_pae.c:3241)
    *dot1xMsgTask: Sep 18 13:56:05.279: 00:14:a5:4b:cf:ef Scheduling deletion of Mobile Station:  (callerId: 6) in 10 seconds
    *dot1xMsgTask: Sep 18 13:56:05.279: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Disconnected state
    *dot1xMsgTask: Sep 18 13:56:05.279: 00:14:a5:4b:cf:ef Not sending EAP-Failure for STA 00:14:a5:4b:cf:ef
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef Reassociation received from mobile on BSSID 24:01:c7:ed:43:62
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef Max Client Trap Threshold: 0  cur: 0
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef Rf profile 200 Clients are allowed to AP wlan
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef In processSsidIE:4202 setting Central switched to TRUE
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef In processSsidIE:4205 apVapId = 3 and Split Acl Id = 65535
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef Applying site-specific Local Bridging override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef Applying Local Bridging Interface Policy for station 00:14:a5:4b:cf:ef - vlan 232, interface id 13, interface 'aginternet'
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef Applying site-specific override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: Sep 18 13:56:07.381: 00:14:a5:4b:cf:ef STA - rates (8): 130 132 139 150 36 48 72 108 12 18 24 96 0 0 0 0
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef STA - rates (12): 130 132 139 150 36 48 72 108 12 18 24 96 0 0 0 0
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef Processing RSN IE type 48, length 20 for mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef Received RSN IE with 0 PMKIDs from mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef Setting active key cache index 8 ---> 8
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef unsetting PmkIdValidatedByAp
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef pemApfDeleteMobileStation2: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Deleted mobile LWAPP rule on AP [24:01:c7:ed:48:70]
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef Updated location for station old AP 24:01:c7:ed:48:70-0, new AP 24:01:c7:ed:43:60-0
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Initializing policy
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 24:01:c7:ed:43:60 vapId 3 apVapId 3 flex-acl-name:
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef apfPemAddUser2 (apf_policy.c:276) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:43:60 from Associated to Associated
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef apfPemAddUser2:session timeout forstation 00:14:a5:4b:cf:ef - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is  0
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_4: Sep 18 13:56:07.382: 00:14:a5:4b:cf:ef Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
    *apfMsConnTask_4: Sep 18 13:56:07.383: 00:14:a5:4b:cf:ef Sending Assoc Response to station on BSSID 24:01:c7:ed:43:62 (status 0) ApVapId 3 Slot 0
    *apfMsConnTask_4: Sep 18 13:56:07.383: 00:14:a5:4b:cf:ef apfProcessAssocReq (apf_80211.c:7391) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:43:60 from Associated to Associated
    *dot1xMsgTask: Sep 18 13:56:07.385: 00:14:a5:4b:cf:ef Station 00:14:a5:4b:cf:ef setting dot1x reauth timeout = 1800
    *dot1xMsgTask: Sep 18 13:56:07.385: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *dot1xMsgTask: Sep 18 13:56:07.385: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 1)
    *Dot1x_NW_MsgTask_7: Sep 18 13:56:07.439: 00:14:a5:4b:cf:ef Received EAPOL START from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:56:07.439: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *Dot1x_NW_MsgTask_7: Sep 18 13:56:07.439: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 2)
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef Reassociation received from mobile on BSSID 24:01:c7:ed:48:72
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef Global 200 Clients are allowed to AP radio
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef Max Client Trap Threshold: 0  cur: 0
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef Rf profile 200 Clients are allowed to AP wlan
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef In processSsidIE:4202 setting Central switched to TRUE
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef In processSsidIE:4205 apVapId = 3 and Split Acl Id = 65535
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef Applying site-specific Local Bridging override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef Applying Local Bridging Interface Policy for station 00:14:a5:4b:cf:ef - vlan 232, interface id 13, interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef Applying site-specific override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_7: Sep 18 13:56:11.016: 00:14:a5:4b:cf:ef processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef STA - rates (8): 130 132 139 150 36 48 72 108 12 18 24 96 0 0 0 0
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef STA - rates (12): 130 132 139 150 36 48 72 108 12 18 24 96 0 0 0 0
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef Processing RSN IE type 48, length 20 for mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef Received RSN IE with 0 PMKIDs from mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef Setting active key cache index 8 ---> 8
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef unsetting PmkIdValidatedByAp
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef pemApfDeleteMobileStation2: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Deleted mobile LWAPP rule on AP [24:01:c7:ed:43:60]
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef Updated location for station old AP 24:01:c7:ed:43:60-0, new AP 24:01:c7:ed:48:70-0
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Initializing policy
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 24:01:c7:ed:48:70 vapId 3 apVapId 3 flex-acl-name:
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef apfPemAddUser2 (apf_policy.c:276) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Associated to Associated
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef apfPemAddUser2:session timeout forstation 00:14:a5:4b:cf:ef - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is  0
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_7: Sep 18 13:56:11.017: 00:14:a5:4b:cf:ef Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
    *apfMsConnTask_7: Sep 18 13:56:11.018: 00:14:a5:4b:cf:ef Sending Assoc Response to station on BSSID 24:01:c7:ed:48:72 (status 0) ApVapId 3 Slot 0
    *apfMsConnTask_7: Sep 18 13:56:11.018: 00:14:a5:4b:cf:ef apfProcessAssocReq (apf_80211.c:7391) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Associated to Associated
    *dot1xMsgTask: Sep 18 13:56:11.020: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *dot1xMsgTask: Sep 18 13:56:11.020: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 1)
    *apfMsConnTask_7: Sep 18 13:56:19.692: 00:14:a5:4b:cf:ef Reassociation received from mobile on BSSID 24:01:c7:ed:48:72
    *apfMsConnTask_7: Sep 18 13:56:19.692: 00:14:a5:4b:cf:ef Global 200 Clients are allowed to AP radio
    *apfMsConnTask_7: Sep 18 13:56:19.692: 00:14:a5:4b:cf:ef Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_7: Sep 18 13:56:19.692: 00:14:a5:4b:cf:ef Rf profile 200 Clients are allowed to AP wlan
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef In processSsidIE:4202 setting Central switched to TRUE
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef In processSsidIE:4205 apVapId = 3 and Split Acl Id = 65535
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef Applying site-specific Local Bridging override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef Applying Local Bridging Interface Policy for station 00:14:a5:4b:cf:ef - vlan 232, interface id 13, interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef Applying site-specific override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef STA - rates (8): 130 132 139 150 36 48 72 108 12 18 24 96 0 0 0 0
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef STA - rates (12): 130 132 139 150 36 48 72 108 12 18 24 96 0 0 0 0
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef Processing RSN IE type 48, length 20 for mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef Received RSN IE with 0 PMKIDs from mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef Setting active key cache index 8 ---> 8
    *apfMsConnTask_7: Sep 18 13:56:19.693: 00:14:a5:4b:cf:ef unsetting PmkIdValidatedByAp
    *apfMsConnTask_7: Sep 18 13:56:19.694: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Initializing policy
    *apfMsConnTask_7: Sep 18 13:56:19.694: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
    *apfMsConnTask_7: Sep 18 13:56:19.694: 00:14:a5:4b:cf:ef 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_7: Sep 18 13:56:19.694: 00:14:a5:4b:cf:ef Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_7: Sep 18 13:56:19.694: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 24:01:c7:ed:48:70 vapId 3 apVapId 3 flex-acl-name:
    *apfMsConnTask_7: Sep 18 13:56:19.694: 00:14:a5:4b:cf:ef apfPemAddUser2 (apf_policy.c:276) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Associated to Associated
    *apfMsConnTask_7: Sep 18 13:56:19.694: 00:14:a5:4b:cf:ef apfPemAddUser2:session timeout forstation 00:14:a5:4b:cf:ef - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is  0
    *apfMsConnTask_7: Sep 18 13:56:19.694: 00:14:a5:4b:cf:ef Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_7: Sep 18 13:56:19.694: 00:14:a5:4b:cf:ef Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
    *apfMsConnTask_7: Sep 18 13:56:19.694: 00:14:a5:4b:cf:ef Sending Assoc Response to station on BSSID 24:01:c7:ed:48:72 (status 0) ApVapId 3 Slot 0
    *apfMsConnTask_7: Sep 18 13:56:19.694: 00:14:a5:4b:cf:ef apfProcessAssocReq (apf_80211.c:7391) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Associated to Associated
    *dot1xMsgTask: Sep 18 13:56:19.696: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *dot1xMsgTask: Sep 18 13:56:19.696: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 1)
    *Dot1x_NW_MsgTask_7: Sep 18 13:56:19.751: 00:14:a5:4b:cf:ef Received EAPOL START from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:56:19.751: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *Dot1x_NW_MsgTask_7: Sep 18 13:56:19.752: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 2)
    *osapiBsnTimer: Sep 18 13:56:49.676: 00:14:a5:4b:cf:ef 802.1x 'txWhen' Timer expired for station 00:14:a5:4b:cf:ef and for message = M0
    *dot1xMsgTask: Sep 18 13:56:49.676: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *dot1xMsgTask: Sep 18 13:56:49.676: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 3)
    *osapiBsnTimer: Sep 18 13:57:19.676: 00:14:a5:4b:cf:ef 802.1x 'txWhen' Timer expired for station 00:14:a5:4b:cf:ef and for message = M0
    *dot1xMsgTask: Sep 18 13:57:19.676: 00:14:a5:4b:cf:ef Reached Max EAP-Identity Request retries (3) for STA 00:14:a5:4b:cf:ef
    *dot1xMsgTask: Sep 18 13:57:19.679: 00:14:a5:4b:cf:ef Sent Deauthenticate to mobile on BSSID 24:01:c7:ed:48:70 slot 0(caller 1x_auth_pae.c:3241)
    *dot1xMsgTask: Sep 18 13:57:19.679: 00:14:a5:4b:cf:ef Scheduling deletion of Mobile Station:  (callerId: 6) in 10 seconds
    *dot1xMsgTask: Sep 18 13:57:19.679: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Disconnected state
    *dot1xMsgTask: Sep 18 13:57:19.679: 00:14:a5:4b:cf:ef Not sending EAP-Failure for STA 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:57:19.679: Stats update: Non Zero value
    *osapiBsnTimer: Sep 18 13:57:29.676: 00:14:a5:4b:cf:ef apfMsExpireCallback (apf_ms.c:614) Expiring Mobile!
    *apfReceiveTask: Sep 18 13:57:29.676: 00:14:a5:4b:cf:ef apfMsExpireMobileStation (apf_ms.c:5803) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Associated to Disassociated
    *apfReceiveTask: Sep 18 13:57:29.676: 00:14:a5:4b:cf:ef Scheduling deletion of Mobile Station:  (callerId: 45) in 10 seconds
    *osapiBsnTimer: Sep 18 13:57:39.676: 00:14:a5:4b:cf:ef apfMsExpireCallback (apf_ms.c:614) Expiring Mobile!
    *apfReceiveTask: Sep 18 13:57:39.677: 00:14:a5:4b:cf:ef apfMsAssoStateDec
    *apfReceiveTask: Sep 18 13:57:39.677: 00:14:a5:4b:cf:ef apfMsExpireMobileStation (apf_ms.c:5935) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Disassociated to Idle
    *apfReceiveTask: Sep 18 13:57:39.677: 00:14:a5:4b:cf:ef pemApfDeleteMobileStation2: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
    *apfReceiveTask: Sep 18 13:57:39.677: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Deleted mobile LWAPP rule on AP [24:01:c7:ed:48:70]
    *apfReceiveTask: Sep 18 13:57:39.677: 00:14:a5:4b:cf:ef Deleting mobile on AP 24:01:c7:ed:48:70(0)
    *apfMsConnTask_7: Sep 18 13:58:04.863: 00:14:a5:4b:cf:ef Adding mobile on LWAPP AP 24:01:c7:ed:48:70(0)
    *apfMsConnTask_7: Sep 18 13:58:04.863: 00:14:a5:4b:cf:ef Association received from mobile on BSSID 24:01:c7:ed:48:72
    *apfMsConnTask_7: Sep 18 13:58:04.863: 00:14:a5:4b:cf:ef Global 200 Clients are allowed to AP radio
    *apfMsConnTask_7: Sep 18 13:58:04.863: 00:14:a5:4b:cf:ef Max Client Trap Threshold: 0  cur: 0
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef Rf profile 200 Clients are allowed to AP wlan
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef In processSsidIE:4202 setting Central switched to TRUE
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef In processSsidIE:4205 apVapId = 3 and Split Acl Id = 65535
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef Applying site-specific Local Bridging override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef Applying Local Bridging Interface Policy for station 00:14:a5:4b:cf:ef - vlan 232, interface id 13, interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef Applying site-specific override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef STA - rates (8): 130 132 139 150 36 48 72 108 0 0 0 0 0 0 0 0
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef STA - rates (12): 130 132 139 150 36 48 72 108 12 18 24 96 0 0 0 0
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_7: Sep 18 13:58:04.864: 00:14:a5:4b:cf:ef Processing RSN IE type 48, length 20 for mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:58:04.865: 00:14:a5:4b:cf:ef Received RSN IE with 0 PMKIDs from mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 18 13:58:04.865: 00:14:a5:4b:cf:ef Setting active key cache index 8 ---> 8
    *apfMsConnTask_7: Sep 18 13:58:04.865: 00:14:a5:4b:cf:ef unsetting PmkIdValidatedByAp
    *apfMsConnTask_7: Sep 18 13:58:04.865: 00:14:a5:4b:cf:ef 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_7: Sep 18 13:58:04.865: 00:14:a5:4b:cf:ef 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_7: Sep 18 13:58:04.865: 00:14:a5:4b:cf:ef 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_7: Sep 18 13:58:04.865: 00:14:a5:4b:cf:ef Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_7: Sep 18 13:58:04.865: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 24:01:c7:ed:48:70 vapId 3 apVapId 3 flex-acl-name:
    *apfMsConnTask_7: Sep 18 13:58:04.865: 00:14:a5:4b:cf:ef apfMsAssoStateInc
    *apfMsConnTask_7: Sep 18 13:58:04.865: 00:14:a5:4b:cf:ef apfPemAddUser2 (apf_policy.c:276) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Idle to Associated
    *apfMsConnTask_7: Sep 18 13:58:04.865: 00:14:a5:4b:cf:ef apfPemAddUser2:session timeout forstation 00:14:a5:4b:cf:ef - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is  0
    *apfMsConnTask_7: Sep 18 13:58:04.865: 00:14:a5:4b:cf:ef Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_7: Sep 18 13:58:04.865: 00:14:a5:4b:cf:ef Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
    *apfMsConnTask_7: Sep 18 13:58:04.865: 00:14:a5:4b:cf:ef Sending Assoc Response to station on BSSID 24:01:c7:ed:48:72 (status 0) ApVapId 3 Slot 0
    *apfMsConnTask_7: Sep 18 13:58:04.865: 00:14:a5:4b:cf:ef apfProcessAssocReq (apf_80211.c:7391) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Associated to Associated
    *dot1xMsgTask: Sep 18 13:58:04.868: 00:14:a5:4b:cf:ef Station 00:14:a5:4b:cf:ef setting dot1x reauth timeout = 1800
    *dot1xMsgTask: Sep 18 13:58:04.868: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *dot1xMsgTask: Sep 18 13:58:04.868: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 1)
    *Dot1x_NW_MsgTask_7: Sep 18 13:58:04.897: 00:14:a5:4b:cf:ef Received EAPOL START from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 18 13:58:04.897: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *Dot1x_NW_MsgTask_7: Sep 18 13:58:04.897: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 2)
    *osapiBsnTimer: Sep 18 13:58:34.876: 00:14:a5:4b:cf:ef 802.1x 'txWhen' Timer expired for station 00:14:a5:4b:cf:ef and for message = M0
    *dot1xMsgTask: Sep 18 13:58:34.876: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *dot1xMsgTask: Sep 18 13:58:34.876: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 3)
    *apfMsConnTask_7: Sep 18 13:58:57.792: Stats update: Non Zero value
    *osapiBsnTimer: Sep 18 13:59:04.876: 00:14:a5:4b:cf:ef 802.1x 'txWhen' Timer expired for station 00:14:a5:4b:cf:ef and for message = M0
    *dot1xMsgTask: Sep 18 13:59:04.876: 00:14:a5:4b:cf:ef Reached Max EAP-Identity Request retries (3) for STA 00:14:a5:4b:cf:ef
    *dot1xMsgTask: Sep 18 13:59:04.879: 00:14:a5:4b:cf:ef Sent Deauthenticate to mobile on BSSID 24:01:c7:ed:48:70 slot 0(caller 1x_auth_pae.c:3241)
    *dot1xMsgTask: Sep 18 13:59:04.879: 00:14:a5:4b:cf:ef Scheduling deletion of Mobile Station:  (callerId: 6) in 10 seconds
    *dot1xMsgTask: Sep 18 13:59:04.879: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Disconnected state
    *dot1xMsgTask: Sep 18 13:59:04.879: 00:14:a5:4b:cf:ef Not sending EAP-Failure for STA 00:14:a5:4b:cf:ef
    *osapiBsnTimer: Sep 18 13:59:14.876: 00:14:a5:4b:cf:ef apfMsExpireCallback (apf_ms.c:614) Expiring Mobile!
    *apfReceiveTask: Sep 18 13:59:14.876: 00:14:a5:4b:cf:ef apfMsExpireMobileStation (apf_ms.c:5803) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Associated to Disassociated
    *apfReceiveTask: Sep 18 13:59:14.876: 00:14:a5:4b:cf:ef Scheduling deletion of Mobile Station:  (callerId: 45) in 10 seconds
    *osapiBsnTimer: Sep 18 13:59:24.876: 00:14:a5:4b:cf:ef apfMsExpireCallback (apf_ms.c:614) Expiring Mobile!
    *apfReceiveTask: Sep 18 13:59:24.876: 00:14:a5:4b:cf:ef apfMsAssoStateDec
    *apfReceiveTask: Sep 18 13:59:24.876: 00:14:a5:4b:cf:ef apfMsExpireMobileStation (apf_ms.c:5935) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Disassociated to Idle
    *apfReceiveTask: Sep 18 13:59:24.876: 00:14:a5:4b:cf:ef pemApfDeleteMobileStation2: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
    *apfReceiveTask: Sep 18 13:

    hello everyone.. thanks for the reply... I changed a few things around..  instead of having 3 NPS server.. I disabled 2 of them and only using 1 for now.. I am trying to keep everything simple and geting working first..  after doing this.. looks like the message from event view is success   I got 2 events int he log..   1. Network policy server granded access to a user.   2.Network Policy server granted full acess to a user because of the host met the defined health policy.
    both sucess...
    I am not getting a DHCP address... for some reason ... here is the log... from the debug.. hopefully someone can help me figure this out..  Thanks again for helping and posting your comments.
    =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.09.19 09:47:17 =~=~=~=~=~=~=~=~=~=~=~=
    *apfMsConnTask_7: Sep 19 09:48:07.590: Stats update: Non Zero value
    *apfMsConnTask_7: Sep 19 09:49:38.135: Stats update: Non Zero value
    *apfMsConnTask_7: Sep 19 09:50:14.516: Stats update: Non Zero value
    *apfMsConnTask_7: Sep 19 09:50:14.525: Stats update: Non Zero value
    *apfMsConnTask_7: Sep 19 09:50:14.526: 00:14:a5:4b:cf:ef Association received from mobile on BSSID 24:01:c7:ed:48:72
    *apfMsConnTask_7: Sep 19 09:50:14.526: 00:14:a5:4b:cf:ef Global 200 Clients are allowed to AP radio
    *apfMsConnTask_7: Sep 19 09:50:14.526: 00:14:a5:4b:cf:ef Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_7: Sep 19 09:50:14.526: 00:14:a5:4b:cf:ef Rf profile 200 Clients are allowed to AP wlan
    *apfMsConnTask_7: Sep 19 09:50:14.526: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Local. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *apfMsConnTask_7: Sep 19 09:50:14.526: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_7: Sep 19 09:50:14.526: 00:14:a5:4b:cf:ef 0.0.0.0 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_7: Sep 19 09:50:14.526: 00:14:a5:4b:cf:ef 0.0.0.0 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_7: Sep 19 09:50:14.526: 00:14:a5:4b:cf:ef In processSsidIE:4202 setting Central switched to TRUE
    *apfMsConnTask_7: Sep 19 09:50:14.526: 00:14:a5:4b:cf:ef In processSsidIE:4205 apVapId = 3 and Split Acl Id = 65535
    *apfMsConnTask_7: Sep 19 09:50:14.526: 00:14:a5:4b:cf:ef Applying site-specific Local Bridging override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_7: Sep 19 09:50:14.526: 00:14:a5:4b:cf:ef Applying Local Bridging Interface Policy for station 00:14:a5:4b:cf:ef - vlan 232, interface id 13, interface 'aginternet'
    *apfMsConnTask_7: Sep 19 09:50:14.526: 00:14:a5:4b:cf:ef Applying site-specific override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *apfMsConnTask_7: Sep 19 09:50:14.526: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Local. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *apfMsConnTask_7: Sep 19 09:50:14.526: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *apfMsConnTask_7: Sep 19 09:50:14.526: 00:14:a5:4b:cf:ef 0.0.0.0 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef 0.0.0.0 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef STA - rates (8): 130 132 139 150 36 48 72 108 12 18 24 96 0 0 0 0
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef STA - rates (12): 130 132 139 150 36 48 72 108 12 18 24 96 0 0 0 0
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef Processing RSN IE type 48, length 20 for mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef Received RSN IE with 0 PMKIDs from mobile 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef Found an cache entry for BSSID 24:01:c7:ed:48:72 in PMKID cache at index 0 of station 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef Removing BSSID 24:01:c7:ed:48:72 from PMKID cache of station 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef Resetting MSCB PMK Cache Entry 0 for station 00:14:a5:4b:cf:ef
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef Setting active key cache index 0 ---> 8
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef unsetting PmkIdValidatedByAp
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef apfMsRunStateDec
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef apfMs1xStateDec
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef 0.0.0.0 RUN (20) Change state to START (0) last state RUN (20)
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef pemApfAddMobileStation2: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *pemReceiveTask: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef 0.0.0.0 Removed NPU entry.
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 24:01:c7:ed:48:70 vapId 3 apVapId 3 flex-acl-name:
    *apfMsConnTask_7: Sep 19 09:50:14.527: 00:14:a5:4b:cf:ef apfPemAddUser2 (apf_policy.c:276) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Associated to Associated
    *apfMsConnTask_7: Sep 19 09:50:14.528: 00:14:a5:4b:cf:ef apfPemAddUser2:session timeout forstation 00:14:a5:4b:cf:ef - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is  0
    *apfMsConnTask_7: Sep 19 09:50:14.528: 00:14:a5:4b:cf:ef Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_7: Sep 19 09:50:14.528: 00:14:a5:4b:cf:ef Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
    *apfMsConnTask_7: Sep 19 09:50:14.528: 00:14:a5:4b:cf:ef Sending Assoc Response to station on BSSID 24:01:c7:ed:48:72 (status 0) ApVapId 3 Slot 0
    *apfMsConnTask_7: Sep 19 09:50:14.528: 00:14:a5:4b:cf:ef apfProcessAssocReq (apf_80211.c:7391) Changing state for mobile 00:14:a5:4b:cf:ef on AP 24:01:c7:ed:48:70 from Associated to Associated
    *dot1xMsgTask: Sep 19 09:50:14.531: 00:14:a5:4b:cf:ef Disable re-auth, use PMK lifetime.
    *dot1xMsgTask: Sep 19 09:50:14.531: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *dot1xMsgTask: Sep 19 09:50:14.531: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 1)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:14.551: 00:14:a5:4b:cf:ef Received EAPOL START from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:14.552: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Connecting state
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:14.552: 00:14:a5:4b:cf:ef Sending EAP-Request/Identity to mobile 00:14:a5:4b:cf:ef (EAP Id 2)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.443: 00:14:a5:4b:cf:ef Received EAPOL EAPPKT from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.443: 00:14:a5:4b:cf:ef Received Identity Response (count=2) from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.443: 00:14:a5:4b:cf:ef EAP State update from Connecting to Authenticating for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.443: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Authenticating state
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.443: 00:14:a5:4b:cf:ef Entering Backend Auth Response state for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.473: 00:14:a5:4b:cf:ef Processing Access-Challenge for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.473: 00:14:a5:4b:cf:ef Entering Backend Auth Req state (id=3) for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.473: 00:14:a5:4b:cf:ef Sending EAP Request from AAA to mobile 00:14:a5:4b:cf:ef (EAP Id 3)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.491: 00:14:a5:4b:cf:ef Received EAPOL EAPPKT from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.491: 00:14:a5:4b:cf:ef Received EAP Response from mobile 00:14:a5:4b:cf:ef (EAP Id 3, EAP Type 25)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.491: 00:14:a5:4b:cf:ef Entering Backend Auth Response state for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.493: 00:14:a5:4b:cf:ef Processing Access-Challenge for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.493: 00:14:a5:4b:cf:ef Entering Backend Auth Req state (id=4) for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.493: 00:14:a5:4b:cf:ef Sending EAP Request from AAA to mobile 00:14:a5:4b:cf:ef (EAP Id 4)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.505: 00:14:a5:4b:cf:ef Received EAPOL EAPPKT from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.505: 00:14:a5:4b:cf:ef Received EAP Response from mobile 00:14:a5:4b:cf:ef (EAP Id 4, EAP Type 25)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.505: 00:14:a5:4b:cf:ef Entering Backend Auth Response state for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.509: 00:14:a5:4b:cf:ef Processing Access-Challenge for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.509: 00:14:a5:4b:cf:ef Entering Backend Auth Req state (id=7) for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.509: 00:14:a5:4b:cf:ef WARNING: updated EAP-Identifier 4 ===> 7 for STA 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.509: 00:14:a5:4b:cf:ef Sending EAP Request from AAA to mobile 00:14:a5:4b:cf:ef (EAP Id 7)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.522: 00:14:a5:4b:cf:ef Received EAPOL EAPPKT from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.522: 00:14:a5:4b:cf:ef Received EAP Response from mobile 00:14:a5:4b:cf:ef (EAP Id 7, EAP Type 25)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.522: 00:14:a5:4b:cf:ef Entering Backend Auth Response state for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.524: 00:14:a5:4b:cf:ef Processing Access-Challenge for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.524: 00:14:a5:4b:cf:ef Entering Backend Auth Req state (id=8) for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.524: 00:14:a5:4b:cf:ef Sending EAP Request from AAA to mobile 00:14:a5:4b:cf:ef (EAP Id 8)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.536: 00:14:a5:4b:cf:ef Received EAPOL EAPPKT from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.536: 00:14:a5:4b:cf:ef Received EAP Response from mobile 00:14:a5:4b:cf:ef (EAP Id 8, EAP Type 25)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.536: 00:14:a5:4b:cf:ef Entering Backend Auth Response state for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.538: 00:14:a5:4b:cf:ef Processing Access-Challenge for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.538: 00:14:a5:4b:cf:ef Entering Backend Auth Req state (id=9) for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.538: 00:14:a5:4b:cf:ef Sending EAP Request from AAA to mobile 00:14:a5:4b:cf:ef (EAP Id 9)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.552: 00:14:a5:4b:cf:ef Received EAPOL EAPPKT from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.552: 00:14:a5:4b:cf:ef Received EAP Response from mobile 00:14:a5:4b:cf:ef (EAP Id 9, EAP Type 25)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.552: 00:14:a5:4b:cf:ef Entering Backend Auth Response state for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.554: 00:14:a5:4b:cf:ef Processing Access-Challenge for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.554: 00:14:a5:4b:cf:ef Entering Backend Auth Req state (id=10) for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.554: 00:14:a5:4b:cf:ef Sending EAP Request from AAA to mobile 00:14:a5:4b:cf:ef (EAP Id 10)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.568: 00:14:a5:4b:cf:ef Received EAPOL EAPPKT from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.568: 00:14:a5:4b:cf:ef Received EAP Response from mobile 00:14:a5:4b:cf:ef (EAP Id 10, EAP Type 25)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.568: 00:14:a5:4b:cf:ef Entering Backend Auth Response state for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.581: 00:14:a5:4b:cf:ef Processing Access-Challenge for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.581: 00:14:a5:4b:cf:ef Entering Backend Auth Req state (id=11) for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.581: 00:14:a5:4b:cf:ef Sending EAP Request from AAA to mobile 00:14:a5:4b:cf:ef (EAP Id 11)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.599: 00:14:a5:4b:cf:ef Received EAPOL EAPPKT from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.599: 00:14:a5:4b:cf:ef Received EAP Response from mobile 00:14:a5:4b:cf:ef (EAP Id 11, EAP Type 25)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.599: 00:14:a5:4b:cf:ef Entering Backend Auth Response state for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.602: 00:14:a5:4b:cf:ef Processing Access-Challenge for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.602: 00:14:a5:4b:cf:ef Entering Backend Auth Req state (id=13) for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.602: 00:14:a5:4b:cf:ef WARNING: updated EAP-Identifier 11 ===> 13 for STA 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.602: 00:14:a5:4b:cf:ef Sending EAP Request from AAA to mobile 00:14:a5:4b:cf:ef (EAP Id 13)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.615: 00:14:a5:4b:cf:ef Received EAPOL EAPPKT from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.615: 00:14:a5:4b:cf:ef Received EAP Response from mobile 00:14:a5:4b:cf:ef (EAP Id 13, EAP Type 25)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.615: 00:14:a5:4b:cf:ef Entering Backend Auth Response state for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.619: 00:14:a5:4b:cf:ef Processing Access-Accept for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.619: 00:14:a5:4b:cf:ef Resetting web IPv4 acl from 255 to 255
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.619: 00:14:a5:4b:cf:ef Resetting web IPv4 Flex acl from 65535 to 65535
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.619: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Local. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.619: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.619: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.619: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.619: 00:14:a5:4b:cf:ef Applying site-specific override for station 00:14:a5:4b:cf:ef - vapId 3, site 'CoreSites', interface 'aginternet'
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.619: 00:14:a5:4b:cf:ef Applying Interface policy on Mobile, role Local. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 232
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.619: 00:14:a5:4b:cf:ef Re-applying interface policy for client
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.619: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.619: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.619: 00:14:a5:4b:cf:ef Inserting AAA Override struct for mobile
        MAC: 00:14:a5:4b:cf:ef, source 4
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.619: 00:14:a5:4b:cf:ef Setting re-auth timeout to 1800 seconds, got from WLAN config.
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.619: 00:14:a5:4b:cf:ef Station 00:14:a5:4b:cf:ef setting dot1x reauth timeout = 1800
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.622: 00:14:a5:4b:cf:ef Creating a PKC PMKID Cache entry for station 00:14:a5:4b:cf:ef (RSN 2)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.622: 00:14:a5:4b:cf:ef Resetting MSCB PMK Cache Entry 0 for station 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.622: 00:14:a5:4b:cf:ef Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.622: 00:14:a5:4b:cf:ef Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.622: 00:14:a5:4b:cf:ef Adding BSSID 24:01:c7:ed:48:72 to PMKID cache at index 0 for station 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.622: New PMKID: (16)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.623:      [0000] 0e 97 09 a5 6c f9 2a 28 58 03 74 d2 8c 51 b7 ba
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.623: 00:14:a5:4b:cf:ef Disabling re-auth since PMK lifetime can take care of same.
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.623: 00:14:a5:4b:cf:ef unsetting PmkIdValidatedByAp
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.623: 00:14:a5:4b:cf:ef PMK sent to mobility group
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.623: 00:14:a5:4b:cf:ef Sending EAP-Success to mobile 00:14:a5:4b:cf:ef (EAP Id 13)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.623: 00:14:a5:4b:cf:ef Found an cache entry for BSSID 24:01:c7:ed:48:72 in PMKID cache at index 0 of station 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.623: 00:14:a5:4b:cf:ef Found an cache entry for BSSID 24:01:c7:ed:48:72 in PMKID cache at index 0 of station 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.623: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.623:      [0000] 0e 97 09 a5 6c f9 2a 28 58 03 74 d2 8c 51 b7 ba
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.623: 00:14:a5:4b:cf:ef Starting key exchange to mobile 00:14:a5:4b:cf:ef, data packets will be dropped
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.623: 00:14:a5:4b:cf:ef Sending EAPOL-Key Message to mobile 00:14:a5:4b:cf:ef
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.623: 00:14:a5:4b:cf:ef Entering Backend Auth Success state (id=13) for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.623: 00:14:a5:4b:cf:ef Received Auth Success while in Authenticating state for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.624: 00:14:a5:4b:cf:ef dot1x - moving mobile 00:14:a5:4b:cf:ef into Authenticated state
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.647: 00:14:a5:4b:cf:ef Received EAPOL-Key from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.647: 00:14:a5:4b:cf:ef Ignoring invalid EAPOL version (1) in EAPOL-key message from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.647: 00:14:a5:4b:cf:ef Received EAPOL-key in PTK_START state (message 2) from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.647: 00:14:a5:4b:cf:ef PMK: Sending cache add
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.648: 00:14:a5:4b:cf:ef Stopping retransmission timer for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.648: 00:14:a5:4b:cf:ef Sending EAPOL-Key Message to mobile 00:14:a5:4b:cf:ef
       state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.653: 00:14:a5:4b:cf:ef Received EAPOL-Key from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.653: 00:14:a5:4b:cf:ef Ignoring invalid EAPOL version (1) in EAPOL-key message from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.653: 00:14:a5:4b:cf:ef Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.653: 00:14:a5:4b:cf:ef Stopping retransmission timer for mobile 00:14:a5:4b:cf:ef
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.654: 00:14:a5:4b:cf:ef apfMs1xStateInc
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.654: 00:14:a5:4b:cf:ef 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.654: 00:14:a5:4b:cf:ef Not Using WMM Compliance code qosCap 00
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.654: 00:14:a5:4b:cf:ef 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 24:01:c7:ed:48:70 vapId 3 apVapId 3 flex-acl-name:
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.654: 00:14:a5:4b:cf:ef apfMsRunStateInc
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.654: 00:14:a5:4b:cf:ef 0.0.0.0 L2AUTHCOMPLETE (4) Change state to RUN (20) last state L2AUTHCOMPLETE (4)
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.656: 00:14:a5:4b:cf:ef 0.0.0.0 RUN (20) Reached PLUMBFASTPATH: from line 6075
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.656: 00:14:a5:4b:cf:ef 0.0.0.0 RUN (20) Adding Fast Path rule
      type = Airespace AP Client
      on AP 24:01:c7:ed:48:70, slot 0, interface = 13, QOS = 0
      IPv4 ACL ID = 255, IPv6 ACL ID = 255,
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.656: 00:14:a5:4b:cf:ef 0.0.0.0 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206  Local Bridging Vlan = 232, Local Bridging intf id = 13
    *Dot1x_NW_MsgTask_7: Sep 19 09:50:21.658: 00:14:a5:4b:cf:ef 0.0.0.0 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
    *pemReceiveTask: Sep 19 09:50:21.658: 00:14:a5:4b:cf:ef 0.0.0.0 Added NPU entry of type 1, dtlFlags 0x0
    *pemReceiveTask: Sep 19 09:50:21.658: 00:14:a5:4b:cf:ef Pushing IPv6: fe80:0000:0000:0000: 290f:8f76:9221:b33d , and MAC: 00:14:A5:4B:CF:EF , Binding to Data Plane. SUCCESS !!
    *DHCP Socket Task: Sep 19 09:50:21.740: 00:14:a5:4b:cf:ef DHCP received op BOOTREQUEST (1) (len 308,vlan 230, port 13, encap 0xec03)
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP selecting relay 1 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP selected relay 1 - 172.17.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP selecting relay 2 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP selected relay 2 - 172.16.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP selecting relay 1 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP selected relay 1 - 172.17.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP   xid: 0x57b5e60d (1471538701), secs: 0, flags: 0
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP   chaddr: 00:14:a5:4b:cf:ef
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP   siaddr: 0.0.0.0,  giaddr: 172.17.232.8
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP sending REQUEST to 172.17.232.1 (len 350, port 13, vlan 232)
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP selecting relay 2 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP selected relay 2 - 172.16.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 2
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP   xid: 0x57b5e60d (1471538701), secs: 0, flags: 0
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP   chaddr: 00:14:a5:4b:cf:ef
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Sep 19 09:50:21.741: 00:14:a5:4b:cf:ef DHCP   siaddr: 0.0.0.0,  giaddr: 172.17.232.8
    *DHCP Socket Task: Sep 19 09:50:21.742: 00:14:a5:4b:cf:ef DHCP sending REQUEST to 172.17.232.1 (len 350, port 13, vlan 232)
    *apfOrphanSocketTask: Sep 19 09:50:22.740: 00:14:a5:4b:cf:ef Orphan Packet from STA - IP 169.254.179.61
    *apfOrphanSocketTask: Sep 19 09:50:22.740: 00:14:a5:4b:cf:ef In apfRegisterIpAddrOnMscb_debug: regType=2  Invalid src IP address, 169.254.179.61 is part of reserved ip address range (caller apf_broff.c:229)
    *apfOrphanSocketTask: Sep 19 09:50:22.740: 00:14:a5:4b:cf:ef IPv4 Addr: 169:254:179:61
    *DHCP Socket Task: Sep 19 09:50:26.303: 00:14:a5:4b:cf:ef DHCP received op BOOTREQUEST (1) (len 308,vlan 230, port 13, encap 0xec03)
    *DHCP Socket Task: Sep 19 09:50:26.303: 00:14:a5:4b:cf:ef DHCP selecting relay 1 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 0.0.0.0  VLAN: 0
    *DHCP Socket Task: Sep 19 09:50:26.303: 00:14:a5:4b:cf:ef DHCP selected relay 1 - 172.17.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:50:26.303: 00:14:a5:4b:cf:ef DHCP selecting relay 2 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:50:26.303: 00:14:a5:4b:cf:ef DHCP selected relay 2 - 172.16.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:50:26.303: 00:14:a5:4b:cf:ef DHCP selecting relay 1 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:50:26.303: 00:14:a5:4b:cf:ef DHCP selected relay 1 - 172.17.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:50:26.303: 00:14:a5:4b:cf:ef DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Sep 19 09:50:26.303: 00:14:a5:4b:cf:ef DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
    *DHCP Socket Task: Sep 19 09:50:26.303: 00:14:a5:4b:cf:ef DHCP   xid: 0x57b5e60d (1471538701), secs: 1280, flags: 0
    *DHCP Socket Task: Sep 19 09:50:26.303: 00:14:a5:4b:cf:ef DHCP   chaddr: 00:14:a5:4b:cf:ef
    *DHCP Socket Task: Sep 19 09:50:26.303: 00:14:a5:4b:cf:ef DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Sep 19 09:50:26.303: 00:14:a5:4b:cf:ef DHCP   siaddr: 0.0.0.0,  giaddr: 172.17.232.8
    *DHCP Socket Task: Sep 19 09:50:26.303: 00:14:a5:4b:cf:ef DHCP sending REQUEST to 172.17.232.1 (len 350, port 13, vlan 232)
    *DHCP Socket Task: Sep 19 09:50:26.303: 00:14:a5:4b:cf:ef DHCP selecting relay 2 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:50:26.303: 00:14:a5:4b:cf:ef DHCP selected relay 2 - 172.16.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:50:26.303: 00:14:a5:4b:cf:ef DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Sep 19 09:50:26.304: 00:14:a5:4b:cf:ef DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 2
    *DHCP Socket Task: Sep 19 09:50:26.304: 00:14:a5:4b:cf:ef DHCP   xid: 0x57b5e60d (1471538701), secs: 1280, flags: 0
    *DHCP Socket Task: Sep 19 09:50:26.304: 00:14:a5:4b:cf:ef DHCP   chaddr: 00:14:a5:4b:cf:ef
    *DHCP Socket Task: Sep 19 09:50:26.304: 00:14:a5:4b:cf:ef DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Sep 19 09:50:26.304: 00:14:a5:4b:cf:ef DHCP   siaddr: 0.0.0.0,  giaddr: 172.17.232.8
    *DHCP Socket Task: Sep 19 09:50:26.304: 00:14:a5:4b:cf:ef DHCP sending REQUEST to 172.17.232.1 (len 350, port 13, vlan 232)
    *DHCP Socket Task: Sep 19 09:50:34.146: 00:14:a5:4b:cf:ef DHCP received op BOOTREQUEST (1) (len 308,vlan 230, port 13, encap 0xec03)
    *DHCP Socket Task: Sep 19 09:50:34.146: 00:14:a5:4b:cf:ef DHCP selecting relay 1 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:50:34.146: 00:14:a5:4b:cf:ef DHCP selected relay 1 - 172.17.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:50:34.146: 00:14:a5:4b:cf:ef DHCP selecting relay 2 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:50:34.146: 00:14:a5:4b:cf:ef DHCP selected relay 2 - 172.16.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:50:34.146: 00:14:a5:4b:cf:ef DHCP selecting relay 1 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:50:34.146: 00:14:a5:4b:cf:ef DHCP selected relay 1 - 172.17.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:50:34.146: 00:14:a5:4b:cf:ef DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Sep 19 09:50:34.146: 00:14:a5:4b:cf:ef DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
    *DHCP Socket Task: Sep 19 09:50:34.147: 00:14:a5:4b:cf:ef DHCP   xid: 0x57b5e60d (1471538701), secs: 3072, flags: 0
    *DHCP Socket Task: Sep 19 09:50:34.147: 00:14:a5:4b:cf:ef DHCP   chaddr: 00:14:a5:4b:cf:ef
    *DHCP Socket Task: Sep 19 09:50:34.147: 00:14:a5:4b:cf:ef DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Sep 19 09:50:34.147: 00:14:a5:4b:cf:ef DHCP   siaddr: 0.0.0.0,  giaddr: 172.17.232.8
    *DHCP Socket Task: Sep 19 09:50:34.147: 00:14:a5:4b:cf:ef DHCP sending REQUEST to 172.17.232.1 (len 350, port 13, vlan 232)
    *DHCP Socket Task: Sep 19 09:50:34.147: 00:14:a5:4b:cf:ef DHCP selecting relay 2 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:50:34.147: 00:14:a5:4b:cf:ef DHCP selected relay 2 - 172.16.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:50:34.147: 00:14:a5:4b:cf:ef DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Sep 19 09:50:34.147: 00:14:a5:4b:cf:ef DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 2
    *DHCP Socket Task: Sep 19 09:50:34.147: 00:14:a5:4b:cf:ef DHCP   xid: 0x57b5e60d (1471538701), secs: 3072, flags: 0
    *DHCP Socket Task: Sep 19 09:50:34.147: 00:14:a5:4b:cf:ef DHCP   chaddr: 00:14:a5:4b:cf:ef
    *DHCP Socket Task: Sep 19 09:50:34.147: 00:14:a5:4b:cf:ef DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Sep 19 09:50:34.147: 00:14:a5:4b:cf:ef DHCP   siaddr: 0.0.0.0,  giaddr: 172.17.232.8
    *DHCP Socket Task: Sep 19 09:50:34.147: 00:14:a5:4b:cf:ef DHCP sending REQUEST to 172.17.232.1 (len 350, port 13, vlan 232)
    *DHCP Socket Task: Sep 19 09:50:49.037: 00:14:a5:4b:cf:ef DHCP received op BOOTREQUEST (1) (len 308,vlan 230, port 13, encap 0xec03)
    *DHCP Socket Task: Sep 19 09:50:49.037: 00:14:a5:4b:cf:ef DHCP selecting relay 1 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:50:49.037: 00:14:a5:4b:cf:ef DHCP selected relay 1 - 172.17.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:50:49.037: 00:14:a5:4b:cf:ef DHCP selecting relay 2 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:50:49.037: 00:14:a5:4b:cf:ef DHCP selected relay 2 - 172.16.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:50:49.037: 00:14:a5:4b:cf:ef DHCP selecting relay 1 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:50:49.037: 00:14:a5:4b:cf:ef DHCP selected relay 1 - 172.17.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:50:49.037: 00:14:a5:4b:cf:ef DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Sep 19 09:50:49.037: 00:14:a5:4b:cf:ef DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
    *DHCP Socket Task: Sep 19 09:50:49.037: 00:14:a5:4b:cf:ef DHCP   xid: 0x57b5e60d (1471538701), secs: 6912, flags: 0
    *DHCP Socket Task: Sep 19 09:50:49.037: 00:14:a5:4b:cf:ef DHCP   chaddr: 00:14:a5:4b:cf:ef
    *DHCP Socket Task: Sep 19 09:50:49.038: 00:14:a5:4b:cf:ef DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Sep 19 09:50:49.038: 00:14:a5:4b:cf:ef DHCP   siaddr: 0.0.0.0,  giaddr: 172.17.232.8
    *DHCP Socket Task: Sep 19 09:50:49.038: 00:14:a5:4b:cf:ef DHCP sending REQUEST to 172.17.232.1 (len 350, port 13, vlan 232)
    *DHCP Socket Task: Sep 19 09:50:49.038: 00:14:a5:4b:cf:ef DHCP selecting relay 2 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:50:49.038: 00:14:a5:4b:cf:ef DHCP selected relay 2 - 172.16.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:50:49.038: 00:14:a5:4b:cf:ef DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Sep 19 09:50:49.038: 00:14:a5:4b:cf:ef DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 2
    *DHCP Socket Task: Sep 19 09:50:49.038: 00:14:a5:4b:cf:ef DHCP   xid: 0x57b5e60d (1471538701), secs: 6912, flags: 0
    *DHCP Socket Task: Sep 19 09:50:49.038: 00:14:a5:4b:cf:ef DHCP   chaddr: 00:14:a5:4b:cf:ef
    *DHCP Socket Task: Sep 19 09:50:49.038: 00:14:a5:4b:cf:ef DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Sep 19 09:50:49.038: 00:14:a5:4b:cf:ef DHCP   siaddr: 0.0.0.0,  giaddr: 172.17.232.8
    *DHCP Socket Task: Sep 19 09:50:49.038: 00:14:a5:4b:cf:ef DHCP sending REQUEST to 172.17.232.1 (len 350, port 13, vlan 232)
    *DHCP Socket Task: Sep 19 09:50:49.038: 00:14:a5:4b:cf:ef Failed to get response for 3 dhcp attempts from client.Total DHCP failed count for the interface aginternet : 2
    *apfMsConnTask_7: Sep 19 09:51:08.682: Stats update: Non Zero value
    *DHCP Socket Task: Sep 19 09:51:20.248: 00:14:a5:4b:cf:ef DHCP received op BOOTREQUEST (1) (len 308,vlan 230, port 13, encap 0xec03)
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP selecting relay 1 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP selected relay 1 - 172.17.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP selecting relay 2 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP selected relay 2 - 172.16.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP selecting relay 1 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP selected relay 1 - 172.17.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP   xid: 0xd07dc597 (3497903511), secs: 0, flags: 8000
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP   chaddr: 00:14:a5:4b:cf:ef
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP   siaddr: 0.0.0.0,  giaddr: 172.17.232.8
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP sending REQUEST to 172.17.232.1 (len 350, port 13, vlan 232)
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP selecting relay 2 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP selected relay 2 - 172.16.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 2
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP   xid: 0xd07dc597 (3497903511), secs: 0, flags: 8000
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP   chaddr: 00:14:a5:4b:cf:ef
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Sep 19 09:51:20.249: 00:14:a5:4b:cf:ef DHCP   siaddr: 0.0.0.0,  giaddr: 172.17.232.8
    *DHCP Socket Task: Sep 19 09:51:20.250: 00:14:a5:4b:cf:ef DHCP sending REQUEST to 172.17.232.1 (len 350, port 13, vlan 232)
    *DHCP Socket Task: Sep 19 09:51:24.351: 00:14:a5:4b:cf:ef DHCP received op BOOTREQUEST (1) (len 308,vlan 230, port 13, encap 0xec03)
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP selecting relay 1 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP selected relay 1 - 172.17.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP selecting relay 2 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP selected relay 2 - 172.16.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP selecting relay 1 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP selected relay 1 - 172.17.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP   xid: 0xd07dc597 (3497903511), secs: 1024, flags: 8000
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP   chaddr: 00:14:a5:4b:cf:ef
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP   siaddr: 0.0.0.0,  giaddr: 172.17.232.8
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP sending REQUEST to 172.17.232.1 (len 350, port 13, vlan 232)
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP selecting relay 2 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP selected relay 2 - 172.16.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 2
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP   xid: 0xd07dc597 (3497903511), secs: 1024, flags: 8000
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP   chaddr: 00:14:a5:4b:cf:ef
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Sep 19 09:51:24.352: 00:14:a5:4b:cf:ef DHCP   siaddr: 0.0.0.0,  giaddr: 172.17.232.8
    *DHCP Socket Task: Sep 19 09:51:24.353: 00:14:a5:4b:cf:ef DHCP sending REQUEST to 172.17.232.1 (len 350, port 13, vlan 232)
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP received op BOOTREQUEST (1) (len 308,vlan 230, port 13, encap 0xec03)
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP selecting relay 1 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP selected relay 1 - 172.17.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP selecting relay 2 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP selected relay 2 - 172.16.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP selecting relay 1 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP selected relay 1 - 172.17.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP   xid: 0xd07dc597 (3497903511), secs: 2816, flags: 8000
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP   chaddr: 00:14:a5:4b:cf:ef
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP   siaddr: 0.0.0.0,  giaddr: 172.17.232.8
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP sending REQUEST to 172.17.232.1 (len 350, port 13, vlan 232)
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP selecting relay 2 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP selected relay 2 - 172.16.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 2
    *DHCP Socket Task: Sep 19 09:51:32.041: 00:14:a5:4b:cf:ef DHCP   xid: 0xd07dc597 (3497903511), secs: 2816, flags: 8000
    *DHCP Socket Task: Sep 19 09:51:32.042: 00:14:a5:4b:cf:ef DHCP   chaddr: 00:14:a5:4b:cf:ef
    *DHCP Socket Task: Sep 19 09:51:32.042: 00:14:a5:4b:cf:ef DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Sep 19 09:51:32.042: 00:14:a5:4b:cf:ef DHCP   siaddr: 0.0.0.0,  giaddr: 172.17.232.8
    *DHCP Socket Task: Sep 19 09:51:32.042: 00:14:a5:4b:cf:ef DHCP sending REQUEST to 172.17.232.1 (len 350, port 13, vlan 232)
    *DHCP Socket Task: Sep 19 09:51:47.040: 00:14:a5:4b:cf:ef DHCP received op BOOTREQUEST (1) (len 308,vlan 230, port 13, encap 0xec03)
    *DHCP Socket Task: Sep 19 09:51:47.040: 00:14:a5:4b:cf:ef DHCP selecting relay 1 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:51:47.040: 00:14:a5:4b:cf:ef DHCP selected relay 1 - 172.17.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:51:47.040: 00:14:a5:4b:cf:ef DHCP selecting relay 2 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:51:47.040: 00:14:a5:4b:cf:ef DHCP selected relay 2 - 172.16.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:51:47.040: 00:14:a5:4b:cf:ef DHCP selecting relay 1 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:51:47.040: 00:14:a5:4b:cf:ef DHCP selected relay 1 - 172.17.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:51:47.040: 00:14:a5:4b:cf:ef DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Sep 19 09:51:47.040: 00:14:a5:4b:cf:ef DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
    *DHCP Socket Task: Sep 19 09:51:47.040: 00:14:a5:4b:cf:ef DHCP   xid: 0xd07dc597 (3497903511), secs: 6656, flags: 8000
    *DHCP Socket Task: Sep 19 09:51:47.040: 00:14:a5:4b:cf:ef DHCP   chaddr: 00:14:a5:4b:cf:ef
    *DHCP Socket Task: Sep 19 09:51:47.040: 00:14:a5:4b:cf:ef DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Sep 19 09:51:47.040: 00:14:a5:4b:cf:ef DHCP   siaddr: 0.0.0.0,  giaddr: 172.17.232.8
    *DHCP Socket Task: Sep 19 09:51:47.040: 00:14:a5:4b:cf:ef DHCP sending REQUEST to 172.17.232.1 (len 350, port 13, vlan 232)
    *DHCP Socket Task: Sep 19 09:51:47.040: 00:14:a5:4b:cf:ef DHCP selecting relay 2 - control block settings:
                dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                dhcpGateway: 0.0.0.0, dhcpRelay: 172.17.232.8  VLAN: 232
    *DHCP Socket Task: Sep 19 09:51:47.041: 00:14:a5:4b:cf:ef DHCP selected relay 2 - 172.16.16.50 (local address 172.17.232.8, gateway 172.17.232.1, VLAN 232, port 13)
    *DHCP Socket Task: Sep 19 09:51:47.041: 00:14:a5:4b:cf:ef DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Sep 19 09:51:47.041: 00:14:a5:4b:cf:ef DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 2
    *DHCP Socket Task: Sep 19 09:51:47.041: 00:14:a5:4b:cf:ef DHCP   xid: 0xd07dc597 (3497903511), secs: 6656, flags: 8000
    *DHCP Socket Task: Sep 19 09:51:47.041: 00:14:a5:4b:cf:ef DHCP   chaddr: 00:14:a5:4b:cf:ef
    *DHCP Socket Task: Sep 19 09:51:47.041: 00:14:a5:4b:cf:ef DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Sep 19 09:51:47.041: 00:14:a5:4b:cf:ef DHCP   siaddr: 0.0.0.0,  giaddr: 172.17.232.8
    *DHCP Socket Task: Sep 19 09:51:47.041: 00:14:a5:4b:cf:ef DHCP sending REQUEST to 172.17.232.1 (len 350, port 13, vlan 232)
    *apfMsConnTask_7: Sep 19 09:52:39.228: Stats update: Non Zero value

Maybe you are looking for