6300 low volume

Is there a way to increase volume output on headset? The current settings are way too low.

I assume you've turned the volume up?
Sorry if you have, but you'll be suprised the amount of people that dont.
If you have and it is still very low, im afraid there isnt anything you can do to turn it up beyond its programmed capability.
However if it is VERY low it may be a fault, and may be a faulty speaker.
My posts are my opinion and in no way the direct views of Nokia.
If my posts are helpful, please give me some KUDOS using the green star on the left.

Similar Messages

  • 6300 - Low Volume of Ring tone

    Hi 6300 users,
    The ring tone volume of my phone is hardly audible. I have of course turned up the volume to the max extent.
    Any suggestions?
    Regards,
    Gururaj

    Ok, it sounds like a software fault.
    It is set to ring but is ringing ascending, so you will need to get the software updated.
    You could try the Nokia Software Updater first.
    If that doesnt work then you should take it to a Nokia Care Point.
    You can find the nearest NCP to you at the Store Locator
    My posts are my opinion and in no way the direct views of Nokia.
    If my posts are helpful, please give me some KUDOS using the green star on the left.

  • Guitar audio drop-out at lower volumes

    I have tried out mainstage on a friends macbook pro, to check if it will be worth an investment into Logic over Garageband, mainly as an effects emulator for my guitar so I don't need to worry about amps in my small flat.   I connected through an Edirol UA-5 USB audio interface and while there were some issues with this interface anyway due to the fact I could only use input-1 rather than the Hi-Z Input-2 that I should use, I wanted to check some audio problems I had and see how to fix them.
    Basically, at full volume on my guitar it seems to work fine, but as soon as I turn the guitar volume knob down there is literally no sustain anymore, I can hear a brief note and then it just cuts out, no gradual loss just stops.   If I only plug the interface in without mainstage then the monitor channel gives me the full volume control I expect and I tried my guitar on a proper external amp and it seemes to be fine so i've eliminated my guitar as the problem.
    Anyone experienced this or have any suggestions to try to get it to work.
    Also, if I use garage band I don't hear the output fromt he amp/effects simulators, only raw guitar and I only hear the final version if I record it and then play it back.  Is there a way to get Garage band to act as a amp/fx simulator in a live mode like mainstage does or is the fact mainstage is playing back through the interface what might be causing the problems in some feedback loop??   Beginning to think an iRig would have been a better option......

    CCTM wrote:
    Djbungo wrote:
    Basically, at full volume on my guitar it seems to work fine, but as soon as I turn the guitar volume knob down there is literally no sustain anymore, I can hear a brief note and then it just cuts out, no gradual loss just stops. 
    Hi
    Sounds like you may have a Noise Gate in there somewhere?
    CCT
    yeah I thought of that but couldn't see anything, and think my knowledge of what a noise gate would do is slightly rusty since I assumed that at louder volumes it would clip and at lower volumes it would be fine....i'll have a play next time I am over my friends and see if I can spot anything.
    Thanks for the quick reply.
    MKS

  • Seemingly low volume for X-Fi Xtrememu

    Today, the second time I booted up my computer I began to receive an interesting problem. My audio worked to some extent, but the volume was exceedingly low. I had to put my ear right next to the speakers to hear anything. I pulled out my headphones and plugged them in -- Same result, low volume. When I disabled the X-Fi and enabled my onboard audio, the volume was crystal clear and worked perfectly fine. I didn't change any software, drivers, hardware, or anything of that sort within the two reboots either.
    I checked the obvious and made sure my volume was high in the X-Fi configuration panel, the windows panel, and my media players. Everything was maxed out. When I turned up my volume to the maximum on my speakers I could hear things better, but it was horribly distorted and sounded as if they were being over dri'ven. Normally I never have to increase the volume on the speakers much to hear anything, their usually on about 20-30% and I hear them perfectly fine.
    I posted about this before on another site and It was recommended I try installing the latest drivers. So I decided to do an uninstall of the X-Fi drivers for good measure and, after rebooting, I installed the drivers and rebooted once more as it prompted me. The same exact result as before: sound that seems to have very low volume. After this, they recommended I try a different PCI slot as it may be damaged. I tried the other PCI slot and I had the same exact results as before. I did not want to install the card into the slot right next to my video card because it looked like the fan would be right up against the PCB of the X-Fi and that it might impede air flow and cause both cards to overheat.
    Does anyone know what might be the problem? I'm using the latest drivers I saw (September 9th I believe) and the X-Fi has worked great for the past week and a half. I really don't want to have to own a $00 paperweight and revert to onboard audio.
    Edit: If it helps any, I'm running on the following:
    Asus A8N32 SLI Deluxe
    AMD Opteron 70
    X-Fi Xtrememusic
    GeForce 7900 GT
    If you need any other info, i'll post it.Message Edited by Sagekilla on 0-22-2006 2:9 PM

    Bump.. Does anyone know how to fix this problem? I've made a list of all the fixes I've attempted
    - Checked the volume in Creative's console, the Windows volume control in my tray bar, and in the Control Panel under "Audio and Sound devices"
    - Made sure default device was the X-Fi
    - Made sure the speakers was plugged in the right spot
    - Made sure the speakers weren't faulty (I tested with a pair of head phones and on my iPod)
    - Made sure I had the latest drivers
    - Did the diagnostic, didn't help
    - Did a system restore that made things worse
    - Switched the PCI slot the sound card was in
    - Tried onboard audio and found the audio there worked fine (I don't want onboard audio and a $00 paper weight though)
    - Made sure onboard audio was uninstalled and disabled
    - Posted on the creative labs forums and got no replies
    - Safe Mode doesn't even recognize the Sound card
    I'm pretty sure this isn't something stupid like "Is the volume turned up?"

  • Low volume warning

    My son is currently having a problem connecting to itunes. When he brings up itunes he gets a low volume warning popup stating that itunes volume has been turned down low, howereve he cannot click past this warning box nor x out of it. He has not been able to use his ipod for the past two months and we aregetting very frustrated. i have tried to uninstall itunes and quick player and then reinstall but nothing has helped. Other than this new issue he has been using it successfully for two years. Please someone help!!!!!!

    Why can't he dismiss the dialog box? Can he see the button on screen? Is it a screen resolution issue?

  • My low volume button doesn't work on my Iphone 4, how can I fix it?

    Okay so I dropped my iphone in the parking lot garages of my apartment complex and the ground was cement, when i picked it up the screen wasn't cracked or anything so i thought it was okay but once i started listening to music and I wanted to lower the volume and so I pushed the low volume button but nothing happen....The high volume button works fine but now the low volume button so if you want to lower the volume on my phone now you have to do it manually....Also after the drop i turned off silent mode on the side and the clicking sound wasn't there and I checked in the settings, it said it was on and the volume was on but I heard no clicking sound!!! How can I solve these two problems? Can I go to an Apple Store and let them fix my iphone if I don't have AppleCare?

    Hi there Jaz94,
    I would recommend taking a look at the troubleshooting steps found in the article below.
    iPhone: No sound or distorted sound from speaker
    http://support.apple.com/kb/ts5180
    -Griff W.

  • No sound vs low volume

    I recently experienced the loss of all sound on my phone. It began after I unplugged the ear phones. I could not hear it ring and I could not hear anyone on the line although they could hear me. It was basically dead for about 4 hours or until I plugged the ear phones back in causing something to reset or whatever. It works fine now and Apple asked that I call when it occurs again so that we can try and trouble shoot and narrow the problem. I may have a defective phone.
    I do not think this has any correlation with the "low volume" problem that everyone is talking about. I will agree with another writer that the volume is low until you activate the speaker but I have been using the speaker/hands free since the first day so perhaps that is why I have never experienced low volume. I think if the speaker is activated everyone will experience normal sound volume.
    Dell   Windows Vista  
    Dell   Windows Vista  

    Faddy wrote:
    I installed the Audigy 2 ZS last night. Updated everything, all of the drivers. I plug in my speakers, and nothing at low volume. I turn on music, and theres nothing. If I turn the volume all the way up, theres distortion, white noise, and a bunch of static, but I can hear the music very faintly. I've disabled the onboard audio, and followed the FAQ, but nothing. Any ideas?
    Output volume is set with "Wave" and "Master" controls. Max the Wave and control with Master.
    In many cases if PSU is weak --> you get issues of this type. Try to remove (temporarily) devices like CD/DVD, floppy, etc. (just remove power/data cables) to see if PSU is the culprit for your issue.
    Also, have you checked/tried
    - audio HW acceleration and SR conversion quality --> set both max
    - audio codecs --> reinstallation can be helpful
    - muted all other sources but the one(s) you're using (i.e. all other sources can be muted if only playing audio files)
    - digital output only set properly (speaker settings/THX console)
    - speakers connected as should (2/2. --> green jack, etc.) and plugs properly pushed in
    - speakers set correct (2/2., 4/4., 5., 6/6., 7.)
    - used different output device drivers on audio players (DS/MME/WDM/...)
    - ASIO capable player --> shows if you have sound driver issue (creative/windows)
    - reinstalled directX, WMP (updates audio codecs)
    - etc.
    jutapaMessage Edited by jutapa on 03-09-200609:34 AM

  • Lower volume button not working

    Lower volume button not working

    Take it to the Genius Bar while you are still under warranty and they should be able to fix it.  I went, one day after my warranty expired.  While they confirmed the problem in my iPhone 5, they said it would be $269 to fix.  The tech did helpfully show me how there's a much less convenient softkey workaround using General >Accessibility > AssistiveTouch.  Not happy about it.

  • The left speaker has lower volume than the right speaker of my pavilion g4-1202ax..

    please help me with this problem..
    the left speaker has low volume..
    but the balance is equal..
    what should i do??
    is any one there wants to help me?? 

    I tried tightning the cables to the computer too.

  • Computer freezes, then a low-volume, high pitch sound

    Hello there,
    My trusty 2002 MDD is randomly freezing on me for the 1st time! Disk Warrior nor Disk Utility form external boot-ups detect anything wrong. Thus, it doesn't seem to be a hard drive issue. Memory status on System Profiler checks OK.
    Once the beach ball appears I can't do anything but press the power button to shut it down. I've noticed that while frozen a very low-volume, high pitch sound can be heard. ???
    Thanks a lot for any feedback that you may provide,
    Jacobo

    Hatter,
    Thanks for the prompt reply. Like you proposed, I've started from my FW drive (not after a freeze though) and everything drive-related checks OK.
    Yes, my video card (Radeon 9800) does have a fan. I've though about this and the PSU as well. The latter is the quieter, less powerful one.
    My drives are less than a year old and seem to be OK.
    I’ve run Applejack (w/ memory check) and all is good.
    Can the Apple Diagnostic CD pinpoint any of these issues?
    My MDD has been incredible when it comes to reliability. She has not given me ANY problems whatsoever while stressed to its limits.
    Thanks again for your time,
    Jacobo

  • Nokia X2-00 with low volume in earpiece

    My Nokia x2-00 became with low volume when in conversations. I have pressed the volume keys to the max, but still the volume is very low.
    Any suggestions? Will a firmware update fix this?
    Thanks,
    Pedro

    hi mate,
    Have you checked via Nokia Suite on your PC if there are any firmware updates available for your device? IF there is, please update to the latest version offered. If that doesn't work, you can try re-installing your current firmware through Nokia Suite and if that doesn't work either, try Restoring your phone to factory settings.
    Failing that, you will need to take your phone to your local Nokia Care for them to inspect: http://nokia.com/support

  • Fix low volume output on Sky HD Boxes

    Here a suggestion for you. Why dont you fix the low volume out on the Sky HD boxes? Loads of people have complained about it. Do something about it.

    I have finally found a very cost effective solution to this problem.  Cancelled Sky subscription and got Freesat with a Humax box.  This does not have the fault that the Sky HD boxes have.  In fact it has an "on the remote" volume control, and when this is turned to max the volume is exactly as it should be.  The volume control works both the HDMI and the analogue outputs.  Additionally there is also a mute button on the remote, again muting both outputs.  Perfect.  Cost effective because since I have been a Sky subscriber for over a decade, now cancelled, assuming I would have stayed with them for another decade I have saved myself £4121 including the initial cost of the Freesat box.  Quite a shocking amount of money that I will be saving, having calculated it.  Shame on Sky for not correcting this software issue when it was first reported by many users, especially as the volume function used to be there and they removed it.  For those thinking of doing the same as me, the Freesat / Freetime system is excellent, the EPG is as good as Sky and the "roll back" TV aspect of the EPG far superior to that of Sky.  Picture quality is at least as good (probably better as box is Full HD)  The BBC iplayer implementation is also not the "cut down" version thst Sky have also implemented (another software short cut that bugged me), i.e. it is the same as you'd see on your PC / smart TVs with FULL programme content.  What you don't get is Sky Atlantic but since I never watched this in over a decade made no difference to me.

  • Audio out low volume

    Our Motorola qip6416-2 suddenly is producing a very low volume on the volume out connectors.  Volume to the TV is OK, but we have both a stereo and a TV-Anywhere hooked up to the audio out, and the volume on both has taken a sudden plunge.  Any suggestions on settings that might need to be adjusted?
    Thanks

    Try looking at the compression setting and the fixed or adjustable setting (all under menu => audio).
    If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem.

  • Low Volume Ipod Classic 2009 from USA?

    Hi,
    I just purchased the new Ipod Classic in October in New York City at the Apple Store. Now, back at home in Switzerland, I loaded the Classic via Itunes. Now I have the feeling that the Classic has a much lower volume than my old 5.5G Ipod Video (from the USA, too. Without EU volume cut). Is this possible? Is the new classic more quiet than the older ones? Firmware problem? May I have the EU Version althoug I bought it in New York? Is there a way to figger out via serial number etc. if my classic is an US or an EU model?
    Does anyone, who lives in the US, the same impression about the volume?
    Note: both Ipods are filled with exactly the same files and "maximum volume" is set to max in both models.
    Thanks a lot for some ideas.
    Gero

    Does anyone, who lives in the US, the same impression about the volume?
    My 2009 160GB USA unit is very loud.
    I think that your computer tells the iPod that you are in the EU and it locks in a lower volume.
    In the EU the 'State' and not the individual controls the volume of YOUR music.
    Talk about "over governed". I guess I'm lucky that the "sound Police" didn't confiscate my USA iPod on a recent trip to Europe.
    Good Luck.

  • Low volume, no enhancements tab to fix issue

    Hello 
    I have a Pavilion g6 HP laptop, running on windows 8. 
    I am experiencing a problem with very low volume. How can I fix this? I have seen in previous questions that this response has worked for people:
    Right click the speaker icon in the Taskbar and select 'Playback Devices'.  Left click the default device once to highlight it ( it's usually 'speakers & headphones' ) then click the Properties button.  Click the Enhancements tab and put a tick in the box next to 'Loudness Equalization'.  Click Apply to save the change and then click OK in all remaining windows and see if this has helped at all.
    However, there is no enhancements tab on my system! Help!
    Thanks

    Same problem here.. This problem is from years with the hp laptop speakers and they do nothing... That is very irresponsible.. Well, HP you're gonna release some official fix for that or what? Seriously I'm going to switch to dell because of your useless support.By the way why are you doing a support forum when you DO NOT KNOW the answer of the problems? Huh... 

Maybe you are looking for

  • HT5624 How do I update my Apple ID on iPad and iPhone after changing it?

    How do I update my Apple ID email address on iPhone and iPad after changing the email but not password.  I have verified my new email on iPhone iPad and iMac but settings on all for iCloud still show my old email address. I can't use anything now tha

  • Exception processing message on K230

    I just got an IdeaCentre K230 (running Vista) and transferred my files from my old computer to the new one using LapLink.  Now the new computer has been crashing, and I keep getting the following message: Windows--no disk Exception Processing Message

  • Crystal 2008 on 64 bit OS

    We had to move to Crystal 2008 to support our application in citrix environment and now we need to support it on a 64 bit OS.  It appears that crystal 2008 can only work in the emulaton mode on a x64 OS. Is there any plan to provide full 64 bit suppo

  • Report in MM

    Dear Experts, Is there any report in MM where we can get End to End details of an procurement activity. For e.g from PR to RFQ,Contract, PO,GR, GI, Miro, payment.... Please do help. Thanks in advance. Dominic Rajan

  • Excise Report

    Hi, How to find out Excise Report with T.Code ? Its Urgent. Regards, Parveen