790FX-GD70 Ram Problem (PLEASE HELP!!)

Hello all,
I recently installed my 790FX-GD70 motherboard with all the ram and all that
I have 2x4gb RAM but when i put both sticks of ram in i do not get anything on the screen but when i install 1 stick of ram into the 2nd dimm windows loads up and all that but after like 10-15minutes i get a blue screen and at the bottom it says "Dumping Physical Memory to Disc" then it reboots loads back to windows and does the same thing again, but i dont know why when i put 2x 4GB ram the same the computer boots up but nothing comes on the screen.
Any help please?
Really need to fix this.
750W PSU
AMD phenom II 850 @ 3.3GHz
2x4gb ram only 1 allowed
2x ASUS GeForce 550TI's
PLEASE HELP ME!!
Nothing is overclocked.

Hello Sorry here are the links to my PSU and RAM!
PSU:
http://www.ebay.co.uk/itm/NEW-QUIET-ARTIC-750W-ATX-PSU-8-PIN-SATA-PCI-E-PFC-120mm-FAN-POWER-SUPPLY-/140722519305?pt=UK_Computing_PowerSupplies_EH&hash=item20c3b73d09#ht_3045wt_1012
RAM:
MTEX 1333MHz-----1111G14JCJ6-----MTC003944
I got these numbers of the ram itself so i don't know which is the model number and the serial number.
And the voltage of the ram is at default. 1.5 i think
I did try and set the voltage to 1.8 and put my 8gb ram in, it booted up to windows and i managed to put 2 sticks of ram in then about 10 minutes later it went to blue screen again and said  dumping physical memory to disc
I done a error check of the ram and it came up with no errors.

Similar Messages

  • P6N Lots of problems please help

    P6N Lots of problems please help
    The setup is the following:
    P4 D935 3.2gHz
    P6N Diamond MS-7320 Bios 1.3V
    Corsair XMS2-6400C4DHX
    NX8600GT-TD512EZ/D2
    Seagate Barracuda 7200 250Gb SataII 16Mb
    Akasa 460W Dual Rail
    Please help I have lots and lots of problems with lockups that can happen any time post , bios , loading vista and sometimes during OS. Some times will work ok play games etc. Already tried different combinations fitting the mem modules even tried and some pc4200 modules same problems. Spent lots of hours clocking the mems with different settings but non is stable. I am not interested in overcloking just to make it stable to start with. When is actually running is fine is more than enough for me. Already looked to lots of posts on the msi forum but… Since the cpu is old can I go back on an older bios version???? The Corsair modules have to run at 2.1V or is it possible to use them with slower setting. So confused so lost ….. please HELLPPPPP
    Any help greatly appreciated.

    please, don't buy any more unneded parts.  first find the problem then buy if no solutions available.
    One thing I find with BIOS issues is to do a full clear.
    1. disconnect the power cord from the power supply(turn switch to off if there is one.
    2. hit the power switch to clear the power out of the system.
    3. set the cmos jumper to clear and leave there if one is available.
    4. Pull the battery.
    5. carefully short out the battery connector on the motherboard to drain any power left.
    6. press the clear cmos button and hold for 30sec minimum, if you didn't have a jumper to set. 
    7. replace battery, move jumper back, plug in power cord, turn on power sipply switch.
    Now it should hopefully power up.  go into BIOS and load optimized results. hit save and exit and when it gets back to the post screen, go back into bios and set your normal MB settings(ie. set boot devices, boot order, disable sound if using sound card, etc...)
    go into your H/W Monitor section and list the CPU Vcore settings to make sure it is getting the power it needs.  I just looked it up and it's suppose to run from 1.225v - 1.325v.
    also, try your most generic ram you have with auto settings.  the faster the ram usually the more volts they need and default volts are 1.8v for ram and sometimes faster chips have issues with lower volts.
    Let me know how this works for you.
    -=Mark=-
    ps. make sure everything is unplugged from the computer you don't need.  just cpu, 1 stick of ram, and video. and of course keyboad and mouse.  Please make a signature with all your systems specs including make and model numbers.  I hate guessing at solutions and I'd hate to see you buy any more unneccessary parts because of lack of information.

  • System D.O.T automatically why? problem please help me

    hello everybody,
                           please help me my system says at post message that wrong cmos information then gives me option to boot or go to bios when i check my bios , my ONBOARD LAN GETS ENABLED AUTOMATICALLY  ,the Frequency tab i check says something like PRIVATE DOT ENABLED AND CPU+AGP SOMETHING i mean my comptuer gets fast and the CPU fan becomes on full speed and i hear loud noise until Corecenter runs it becomes quiet again. the question is is this a bios fault or something , DID ANYBODY WHO BOUGHT 865PE PLATINIUM BOARD EXPERIENCE THIS PROBLEM PLEASE HELP ME MY CONFIGURATIONS ARE BELOW
    PENTIUM 2.40 GHZ PRESCOTT (54 C MAXIMUM)
    MSI 865PE PLATINIUM BOARD (IT GOT NO RAID ABILITY)
    DDR 400 MHZ KINGSTON SINGLE CHIP RAM (ALTHOUGH IT RUNS AT 333MHZ)
    MSI GEFORCE FX 5200 T128 (64 BIT DAMN IT!!!)
    MSI CD ROM
    SONY FLOPPY
    COMPUTER CASING WITH SMALL MINI ADDITIONAL FAN ON THE SIDE (IT RUNS MAYBE AND ALSO GIVES ELECTRIC SHOCK OR SOMTHING SOMETIMES)
    STABIMATIC 500V AUTOMATIC STABILIZER(ALTHOUGH I HAVE UPS CAN SOME BODY TELL ME IS UPS ALSO STABILIZER OF APC(AMERICAN POWER ----)
    AMI BIOS 3.4
    SO CAN ANY BODY TELL ME IF THIS IS A PROBLEM OF BIOS SHOULD I UPGRADE TO LATEST
    WHAT METHOD THROUGH AUTOUPDATE OR MANUAL , I ONLY ONCE DID MANUALLY ON MY DELL 4100 PIECE OF CAKE !

    Hi,
    Go to here for MSI LIVEUPDATE
    http://www.msi.com.tw/program/support/software/swr/spt_swr_detail.php?UID=556&kind=1
    Install and run program.........
    BIOS problems:
    http://www.msi.com.tw/html/support/bios/note/boot.htm
    If you would like to download bios and install........
    http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=556&kind=1
    You can also choose 3.7 if wish too first.....
    I am sure this will help you.
    Del

  • 990fxa gd80 raid 0 problem please help me i am begging you

    so i will start with my set up
    990fxa dg80 mb
    fx 8350 cpu
    780ti
    8 gig of ram
    256 hdd
    2x samsung 850 evo
    750 hybrid drive
    So at this stage all my data is on the 750 hdd and the disk is stored away. my problem started with me buyng 2 mx100 256 ssds . If my bios is set to ide or ahci they work fine i had my windows instaled on 1 of them all woks fine. Once i switch my bios to raid ( before i set up my raid 0) boot up win 7 instalation i do not see any drives ( i know is normal) load the drivers for the raid controler (sb950 for w7 as it says in themanual) and only my 256 hdd shows up but not the ssds . Than i set them up in ld raid 0 same problem . Tryed on another 2 mbs ... 1 same and a gygabite same problem. So i was sure there is a problem with ssds. I got rid of them got 2 new 850 evo 250 gb same problem. please help me i am so desparate i am willing to pay woth body organs for help

    I..have a few questions...
    1. You set BIOS to the RAID mode, and under that option there's a Board SATA RAID ROM, do you set it as Legacy ROM?
    2. Did you enter Ctrl+F to initialize the drives/Delete Array(If they're used SSDs) and create RAID0?
    3. Is your Win7 64 bit or 32 bit?
    4. I assume it's 64 bit, did you copy the W764 folder for driver loading?
    And make sure you get the driver from here:
    http://www.msi.com/support/mb/990FXAGD80.html#down-driver&Win7 64

  • My iphone is on recovery mode and i can´t turn on it, when i try to recover it from itunes i get: "unknown error (36), i´ve tried to do lot of things but i can´t  solve my problem. please help!!

    my iphone is on recovery mode and i can´t turn on it, when i try to recover it from itunes i get: unknown error (36), i´ve tried to do lot of things but i can´t solve my problem. please help!!

    Hi, i had the same problem. Try to find the file "apple" or "itunes" don't know it anymore exactly. Ahm well you need to delet any information or just plug in your iphone into an other computer. important is that your iphone never has been pluged in this computer before. This was what i did, and it worked!

  • Problem Please help me.....Let me know the area to look for it I am a DBA..

    Problem Please help me.....Let me know the area to look for it I am a DBA..Thanks in advance to let me know the cause and the area to look and fix it...
    Server Error in '/' Application.
    Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
    Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
    Exception Details: System.Web.Services.Protocols.SoapException: Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
    Source Error:
    An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below. 
    Stack Trace:
    [SoapException: Problem with SAP/BAPI.
    SAP.Connector.RfcCommunicationException: Connect to message server failed
    Connect_PM  MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD
    LOCATION    CPIC (TCP/IP) on local host
    ERROR       service 'sapmsPRD' unknown
    TIME        Wed May 04 08:59:06 2005
    RELEASE     620
    COMPONENT   NI (network interface)
    VERSION     36
    RC          -3
    MODULE      ninti.c
    LINE        428
    DETAIL      NiPServToNo
    SYSTEM CALL getservbyname
    COUNTER     1
       at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode)
       at SAP.Connector.SAPConnection.Open()
       at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn)
       at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn)
       at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type)
       at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)]
       System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall) +1503
       System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) +218
       SoftwareKeyUI.InstalledBaseDataWS.InstalledBaseData.LoadKPIRegionMulti(DataSet products)
       SoftwareKeyUI.InstalledBaseDataAccess.LoadKPIRegionMulti(DataSet products)
       SoftwareKeyUI.InstalledBase.GetRegionDetails(Int32 userId, String product, String regionType)
       SoftwareKeyUI.FilteredAccess.GetRegionDetails(Int32 userId, String product, String regionType)
       SoftwareKeyUI.search.LoadRegionDetails()
       SoftwareKeyUI.search.regionType_SelectedIndexChanged(Object sender, EventArgs e)
       System.Web.UI.WebControls.ListControl.OnSelectedIndexChanged(EventArgs e) +108
       System.Web.UI.WebControls.DropDownList.System.Web.UI.IPostBackDataHandler.RaisePostDataChangedEvent() +26
       System.Web.UI.Page.RaiseChangedEvents() +115
       System.Web.UI.Page.ProcessRequestMain() +1099

    The error is a very basic one - the sapmsPRD service is not known. You will have to go to <NT_ROOT>\system32\drivers\etc and add the entry sapmsPRD 3600 to this file.
    This is basically telling the requester at what port to look for the message server.
    C

  • Problem Please help me.....Let me know the area to look for it

    Problem Please help me.....Let me know the area to look for it I am a DBA..Thanks in advance to let me know the cause and the area to look and fix it...
    Server Error in '/' Application.
    Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable&amp; Kpi_Regions, ZSOFT_PROD_TYPETable&amp; Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
    Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
    Exception Details: System.Web.Services.Protocols.SoapException: Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable&amp; Kpi_Regions, ZSOFT_PROD_TYPETable&amp; Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
    Source Error:
    An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
    Stack Trace:
    [SoapException: Problem with SAP/BAPI.
    SAP.Connector.RfcCommunicationException: Connect to message server failed
    Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD
    LOCATION CPIC (TCP/IP) on local host
    ERROR service 'sapmsPRD' unknown
    TIME Wed May 04 08:59:06 2005
    RELEASE 620
    COMPONENT NI (network interface)
    VERSION 36
    RC -3
    MODULE ninti.c
    LINE 428
    DETAIL NiPServToNo
    SYSTEM CALL getservbyname
    COUNTER 1
    at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode)
    at SAP.Connector.SAPConnection.Open()
    at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn)
    at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn)
    at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable&amp; Kpi_Regions, ZSOFT_PROD_TYPETable&amp; Prod_Type)
    at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)]
    System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall) +1503
    System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) +218
    SoftwareKeyUI.InstalledBaseDataWS.InstalledBaseData.LoadKPIRegionMulti(DataSet products)
    SoftwareKeyUI.InstalledBaseDataAccess.LoadKPIRegionMulti(DataSet products)
    SoftwareKeyUI.InstalledBase.GetRegionDetails(Int32 userId, String product, String regionType)
    SoftwareKeyUI.FilteredAccess.GetRegionDetails(Int32 userId, String product, String regionType)
    SoftwareKeyUI.search.LoadRegionDetails()
    SoftwareKeyUI.search.regionType_SelectedIndexChanged(Object sender, EventArgs e)
    System.Web.UI.WebControls.ListControl.OnSelectedIndexChanged(EventArgs e) +108
    System.Web.UI.WebControls.DropDownList.System.Web.UI.IPostBackDataHandler.RaisePostDataChangedEvent() +26
    System.Web.UI.Page.RaiseChangedEvents() +115
    System.Web.UI.Page.ProcessRequestMain() +1099

    Hi
    You should make a mapping for the service sapmsPRD in your /etc/services file (On Windows: C:WINDOWSSYSTEM32DRIVERSETCservices). If your instance number is 00 you will have to add the following entry:
    sapmsPRD      3600/tcp
    Good luck!
    René van Es

  • [TV@Master] Problem please help

    I have Msi.mother board PT8-Neo -LSR ,  Model No.Ms-6799 , main board bios -Phonenix ,maind board version i updat it to 2.2 , cpu size 2.4 G celleron D/256/533 , memory size 256DDram (400),display card Nvidia Riva TNT2 model 64
    the problem that i face it when i put my TV@nywhere -master card ,the pc stop at the main page that show the biso version and name of bios company and the letters do not bost well it look like a virus work , and when i take tha card off the pc go normally , i tried put it to other PCI the same problem
    please help

    i meany by fix the problem of getting the pc go on to windows with card on PCI salot but i still have the broblem of the driver
    please read my reply again
    my operating system is win me and i have also another pc have XP
    when i log in to windows the system show that found my TV@nywhere card but it didnt took the installatin driver for it i tried to install the driver directly
    but it give me this 2 mesages  when i try to install the driver
    MSI TV card is not found ,stop the installation
    the other message is
    MSI pvs driver installatin failed
    i download the driver from msi page also give me the same messages
    for known on Device Manager it show me that the driver there but do not have the driver and the ? mark beside them
    what to do now 

  • I want to buy an in-app purchase but i don`t remember my security questions and i cant access my recovery email either, what can i do? i have 100$ on my account and cant use it because of that problem, please help URGENT

    I want to buy an in-app purchase but i don`t remember my security questions and i cant access my recovery email either, what can i do? i have 100$ on my account and cant use it because of that problem, please help URGENT

    If you have a rescue email address on your account then you can use that - follow steps 1 to 5 half-way down this page will give you a reset link on your account : http://support.apple.com/kb/HT5312
    If you don't have a rescue email address (you won't be able to add one until you can answer your questions) then you will need to contact Support in your country to get the questions reset : http://support.apple.com/kb/HT5699

  • I'm in trouble, my iPod Touch is giving 4th shock when recharge and the battery does not last any more. who knows or has a similar problem, please help me. Note: all this after I downloaded the new version OS5.

    I'm in trouble, my iPod Touch is giving 4th shock when recharge and the battery does not last any more. who knows or has a similar problem, please help me. Note: all this after I downloaded the new version OS5.

    I would make an appointment at the Genius Bar of an Apple store because of the shock issue. I doubt it was caused by the update.

  • My iphone 4 is acting like crap right i can't even restore it everytime i try to reboot it my iphone freezes at the apple logo it is ******* to the point where i just want to smash it how do i solve this problem please help?

    my iphone 4 is acting like crap right i can't even restore it everytime i try to reboot it my iphone freezes at the apple logo it is ******* me off to the point where i just want to smash it how do i solve this problem please help?

    Don't worry, just follow these steps to fix iPhone stuck on Apple logo
    => First of all Start your Computer and then connect with Internet connection, now Download the latest version of the iTunes application
    => Now install the iTunes application in your System and connect your Device with computer via Data cable
    => Now connect your Device with iTunes application and then Tab on summary option, see in the left side bar of iTunes
    => Now Select restore option from iTunes and then confirm the Restore Message for better results. After this unplug your Device and Restart it
    I hope that will surely
    Thank you...

  • Hello!i have problem to insttal potoshop cs6 this is,we've encountered the following issues.installer failed to initialize.this could be due to a missing file.please download adobe support advisor to detected the problem.please,help me

    this is,we've encountered the following issues.
    installer failed to initialize.this could be due to a missing file.please download adobe support advisor to detected the problem.
    please,help me!

    Hi there Mylenium, is there any way you can help me? My cs6 is doing all kinds weird things lately. The liquifying too stopped working completely, when I try to work with the actions, it starts flickering and changing opacity in color by itself. It starts flickering and is completely out of whack! I tried uninstalling and reinstalling and still no luck. I tried getting in touch with adobe and no luck with that neither! Is there anyway you might be able to help?

  • My iPad stop working suddenly i see black screen only pressing the home? and sleep button dose not solve the  problem please help?

    My iPad stop working suddenly i see black screen only pressing the home and sleep button dose not solve the problem please help ?

    Frozen or unresponsive iPad
    Resolve these most common issues:
        •    Display remains black or blank
        •    Touch screen not responding
        •    Application unexpectedly closes or freezes
    http://www.apple.com/support/ipad/assistant/ipad/
    iPad Frozen, not responding, how to fix
    http://appletoolbox.com/2012/07/ipad-frozen-not-responding-how-to-fix/
    iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
    http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
    Black or Blank Screen on iPad or iPhone
    http://appletoolbox.com/2012/10/black-or-blank-screen-on-ipad-or-iphone/
    What to Do When Your iPad Won't Turn On
    http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/TS3281
    Home button not working or unresponsive, fix
    http://appletoolbox.com/2013/04/home-button-not-working-or-unresponsive-fix/
    Fixing an iPad Home Button
    http://tinyurl.com/om6rd6u
    iPad: Basic troubleshooting
    http://support.apple.com/kb/TS3274
     Cheers, Tom

  • I am using firefox 3.6.17 i upgraded it to 4.1.but it does not work properly sometimes it opens every website and most of the time it does not work . so what is the problem please help . thank you

    i am using firefox 3.6.17 i upgraded it to 4.1.but it does not work properly sometimes it opens every website and most of the time it does not work . so what is the problem please help . thank you

    Did you check your security software (firewall)?
    A possible cause is security software (firewall) that blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
    Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process.
    See:
    * [[Server not found]]
    * [[Firewalls]]

  • My Ipad 2 does not turn on when not plugged to electricity. Even when plugged to electricity, it constantly restarts/switches itself off. what is the problem, please help??

    My Ipad 2 does not turn on when not plugged to electricity. Even when plugged to electricity, it constantly restarts/switches itself off. what is the problem, please help??

    i plugged it and pressed the home button for a few seconds. the connect to itunes screen appeared and the moment i disconnect the cable from the electric plug, it switches off. when i connect the cable to the PC, nothing happens, its as if nothing has been done.

Maybe you are looking for

  • PDF size in px in different readers

    Hello! I'm generating a PDF with pictures and I want the pictures to have exactly a certain size in pixels (e.g. 200x200 px) on monitor when viewed from a PDF reader (when zoom is 100 %). But Adobe Reader shows PDF (and thus the picturesú bigger, i.e

  • Classpath Problem (Using JSAPI)

    Hi, I using IBM Via Voice as a the implementation of the JSAPI on my system. I've downloaded the speech for java pack from IBM Alphaworks and put it in the directory of c:\ibmjs This gives you access to the speech packages for utilisation in your pro

  • No smart cover unlock option iPad 3?

    I am looking in the "General" setting for my iPad 3 and there is no option for the Smart cover unlock feature? My sisters iPad 2, iOS 5.1, has the feature so why wouldn't the iPad 3 have it?

  • Quicktime will play .avi video but no sound

    I've been able to play .avi files with sound and video before but for some reason this one file is refusing to play sound and only this one file. why would this be?

  • Differing Fiscal year for Accounting & Tax purposes

    What procedure needs to be followed in ECC 6.0 when the fiscal year for accounting purposes and the fiscal year for taxation purposes are different. For Accounting  - Jan to Dec: For taxn - April to March. How to accomplish the same? One should not e