88 Charges and 3hrs 15min full charge battery good?

3hrs 15min seems a little low with just 88 charges, i got about a month left before my warrenty is up, sould i take a trip to the apple store tommorow or is this a decent charge length ?

It depends on what you are doing. If you have wireless, and bluetooth running, that sounds about right. If these are off, that seems to be a little low, but its hard to say.

Similar Messages

  • I have a bad idea I might of blown up mu iPod touch 5th generation battery by a mistake, please any suggestions on how i could try and turn it on? It is completely blank and it had full charge before it shut off. In need of desperate help :-(

    I have a bad idea I might of blown up my iPod touch 5th generation battery by a mistake, please any suggestions on how i could try and turn it on? It is completely blank and it had full charge before it shut off. In need of desperate help :-(
    Would be very grateful if someone could get back to me
    Thank you very much

    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable
    - Try on another computer                            
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • Hello.  I recently pieced together a late 2008 MacBook Pro 15".  Everything works fine except the battery constantly goes between "not charging" and "calculating" or, rarely "charging". It does charge after a long while and will report that it is charged.

    Hello.  I recently pieced together a late 2008 MacBook Pro 15".  Everything works fine except the battery constantly goes between "not charging" and "calculating" or, rarely "charging". It does charge after a long while and will report that it is charged.
    I have reset the NVRAM and the SMC a couple of time but that didn't work so I ran an Apple Hardware Test and while testing the logic board it gives the following error:
    4SNS/1/40000000 LB1T
    I've done some research and found this is a temperature sensor related to the battery, but cannot find where the sensor is located in the computer.  Would you know how I can find the sensor to test it?  Could my battery problem be related to something else?  Would a fresh install of Lion help?
    Thank you!
    Mike
    Two pieces of information that may or may not b helpful, the hard drive is from my early 2008 MBP and the only test disc I have access to is from an iMac.

    Why do you have LION installed on that older machine?
    So you say you built a macbook from a bucket of parts eh?   Kudos
    heres a pic of the battery temp sensor

  • Just bought new battery charged it and the mac finds it but can't start it without charger and when i remove charger in os it dies right away what to do???

    Just bought New battery charged it and the mac finds it but can't start it without charger and when i remove charger in os it dies right away what to do???
    Here´s some info:
    Macbook Pro 2008 (Early)
    Lion
    Some INFO from power in about mac
    It´s Danish hope you can understand the info
    Batterioplysninger:
      Modeloplysninger:
      Serienummer:
      Producent:          SMP
      Enhedsnavn:          ASMB012
      Pack Lot Code:          a0b0
      PCB Lot Code:          c0f1
      Firmware-version:          8800
      Hardwarerevision:          0
      Cellerevision:          0
      Oplysninger om batterispænding:
      Resterende kapacitet (mAh):          5200
      Fuldt opladt:          Ja
      Oplader:          Nej
      Fuld ladekapacitet (mAh):          5200
      Oplysninger om batteritilstand:
      Antal cykler:          1
      Betingelse:          Normal
      Batteri installeret:          Ja
      Strømstyrke (mA):          0
      Spænding (mV):          11796
    Energiindstillinger til system:
      AC-strømforsyning:
      Interval for vågeblus for system (minutter):          30
      Interval for vågeblus for disk (minutter):          10
      Interval for vågeblus for skærm (minutter):          10
      Genstart automatisk efter strømafbrydelse:          Nej
      Afbryd vågeblus ved ændret spændingskilde:          Nej
      Afbryd vågeblus, når skærmen slås op:          Ja
      Afbryd vågeblus via LAN:          Ja
      Aktuel strømkilde:          Ja
      Vågeblus dæmper lysstyrken:          Ja
      PrioritizeNetworkReachabilityOverSleep:          0
      RestartAfterKernelPanic:          157680000
      Batteri:
      Interval for vågeblus for system (minutter):          10
      Interval for vågeblus for disk (minutter):          10
      Interval for vågeblus for skærm (minutter):          2
      Afbryd vågeblus ved ændret spændingskilde:          Nej
      Afbryd vågeblus, når skærmen slås op:          Ja
      Vågeblus dæmper lysstyrken:          Ja
      Formindsk lysstyrke:          Ja
      RestartAfterKernelPanic:          157680000
    Hardwarekonfiguration:
      UPS installeret:          Nej
    Oplysninger om oplader:
      Tilsluttet:          Ja
      Id:          0x0100
      Watt (W):          85
      Revision:          0x0000
      Familie:          0x00ba
      Serienummer:          0x004fe0c9
      Oplader:          Nej

    Take it to an Apple Genius Bar to be checked out. It will either be the battery or the Logic board (not sure the charging circuit is a separate part. If it is then it mya be just that part).
    If logic board just use it plugged in as for the cost of changing out the logic board you can buy a new system.

  • Ipod keeps charging does not show full charge

    my ipod is only a year old and is not completing the charging cycle showing the full charge have already rebooted???

    you might believe that this is too much information.
    neither beloved nor i have any idea why belladonna was called belladonna. i only rediscovered that that was her name when i saw that in an event log entry while i was doing a troubleshoot here at Discussions. we've discussed the matter at length, and the best we can come up with is "it must have seemed like a good idea at the time".
    mauve did not have a name until attractive beast came on the scene. when i first got attractive beast, i believe i thought "what an attractive beast you are," and the name came pretty easily after that.
    beloved had been using mauve on a regular basis prior to that. the "b noir" and "beloved" pseudonyms actually date back to the late-80s/early-90s. beloved's full psuedonym is "m beloved", where the m stands for "mauve". so the ipod that beloved used most became mauve, too.
    even though beloved chose the "mauve" pseudonym for herself, she does not like it as a name for an ipod, and constantly refers to mauve as "the mypod".
    green eyes is a green 2nd gen, and i'm fond of husker du.

  • I just replaced my iPod a week ago, and it was working fine, but when I went to go turn the screen on, it wouldn't turn on. Ive tried to put it on the charger and it wouldn't charge and it wont connect to my computer, how do i fix this?

    I just replaced my iPod 5th gen. a week ago, and it was working fine, but when I went to go turn the screen on, it wouldn't turn on. I've tried to put it on the charger and it wouldn't charge and it wont connect to my computer, how do i fix this? I tried to reset the iPod, by pressing the home and power button but nothing works. It's literally a brand new iPod, I dont know what to do now. Help?

    Try:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable                                                       
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • My MacBook Pro went off for 30 hours because I forgot my charger and now I am charging it it refuses to turn on and I have been charging it for almost 3 hours  , any have an idea on this ?

    My MacBook Pro went off for 30 hours because I forgot my charger and now I am charging it it refuses to turn on for the last 3 hours , any have an idea on this ?

    Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".

  • I'm conecting my Ipad to the computer to charge and it shows the charging sing for a few seconds then says not charging, do I need to bring it in to get that fixed or is there something I can try to do on my own?

    I'm conecting my Ipad to the computer to charge and it shows the charging sign for a few seconds then says not charging, do I need to bring it in to get that fixed or is there something I can try to do on my own?

    The quickest way (and really the only way) to charge your iPad is with the included 10W USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
    Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
    How to Calibrate Your Mac, iPhone, or iPad Battery
    http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
    At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
    Also, if you have a 3rd generation iPad, look at
    Apple: iPad Battery Nothing to Get Charged Up About
    http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
    Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
    http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
    New iPad Takes Much Longer to Charge Than iPad 2
    http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
    Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
    Extend iPad Battery Life (Look at pjl123 comment)
    https://discussions.apple.com/thread/3921324?tstart=30
    New iPad Slow to Recharge, Barely Charges During Use
    http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
    Tips About Charging for New iPad 3
    http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
    Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
    http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
    iPhone, iPod, Using the iPad Charger
    http://support.apple.com/kb/HT4327
    Install and use Battery Doctor HD
    http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
    In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
     Cheers, Tom

  • TS3274 My iPad wont charge and I bought another charger and it still won't charge

    My iPad wont charge and I bought another charger and it still won't charge

    Could it be the cable?  Did you try another one?

  • I just bought a new 10watt usb power charger and it says not charging?

    I just bought a new 10watt usb power charger and it says not charging?

    Maybe the charger is OK , but the cable may be damaged.

  • My iphone wont respond when fully charged and kept on mains charge is this right?

    My iphone screen wont respond when fully charged and kept on mains charge is this the norm?

    No that isn't normal.

  • My iPad will not charge and every time I charge it. It comes up with the iTunes icon and I will not charge, it is not a new I pad and the same charger I use for the I pad I use for my I phone and it will charge. What is wrong?

    My iPad will not charge and every time I charge it. It comes up with the iTunes icon and I will not charge, it is not a new I pad and the same charger I use for the I pad I use for my I phone and it will charge. What is wrong?

    What exactlyare you seeing on the iPad's screen ? If it's the iTunes icon and a cable then that means that it's gone into recovery mode - you will need to connect it to your computer's iTunes and you should be able to use that to reset it back to factory defaults and you can then restore/resync your content to it.

  • Time since last full charge not displaying despite full charge last night

    I've had my iPhone 5 for almost a week. I noticed the battery drains quickly, did some research on the boards and realized it wasn't just me. I conditioned the battery last night, ran it out til the power shut down then charged through the night til it was 100% this morning. The battery still drains quickly and under settings > general > usage the "Time since last full charge" does not display. I know it was working over the weekend but yesterday i had the same problem before the charge (i figured it was because i hadn't charged it all the way the previous charge). Any suggestions? Location services is still set to ON for diagnostics and usage. I've tweaked a few of the notifications and location service settings so it could be something i changed, but i doubt it. Really coincidental that the usage won't display and the battery is draining like crazy.

    Mine is doing the same thing now that I have updated to 6.0.1. Battery life is way worse than before the update and again the "Time since last full charge" is not displaying any statistics.

  • Ipad 3 charging and sync issues (only charge while turned off)

    Hello,
    I recently came into possession of an iPad 3rd generation, 32GB with Verizon network. Upon gaining possession I was informed of two issues with the device. One was a busted screen and the other was that it would not sync to iTunes. The person stated that he had taken it to a store and they informed him it was the dock connector and he had it replaced. Once they replaced it the issue was still apparent and he asked for them to remove it and put original back. At this time the screen was busted. I purchased the iPad and ordered new screen and dock connector. The parts arrived today and while the screen is fixed I am still having issues with the docking of the iPad. First off I have restored the device several times, tried different cables and different plugins to include both my USB ports on my Mac and wall plugs. None of which are charging or syncing the iPad. I have completely disassembled the device down to the battery and still no change. What is interesting is the fact that I turn the device off and plug in the charging cord the device turns on. If I leave it plugged in while I shut it down it will charge. Only charging when the device is turned off. With this I assume the port is working. I have tried DFU and recovery to try force syncing to iTunes with no such luck. Any advice as to where to start or what to do?

    Hello,
    I recently came into possession of an iPad 3rd generation, 32GB with Verizon network. Upon gaining possession I was informed of two issues with the device. One was a busted screen and the other was that it would not sync to iTunes. The person stated that he had taken it to a store and they informed him it was the dock connector and he had it replaced. Once they replaced it the issue was still apparent and he asked for them to remove it and put original back. At this time the screen was busted. I purchased the iPad and ordered new screen and dock connector. The parts arrived today and while the screen is fixed I am still having issues with the docking of the iPad. First off I have restored the device several times, tried different cables and different plugins to include both my USB ports on my Mac and wall plugs. None of which are charging or syncing the iPad. I have completely disassembled the device down to the battery and still no change. What is interesting is the fact that I turn the device off and plug in the charging cord the device turns on. If I leave it plugged in while I shut it down it will charge. Only charging when the device is turned off. With this I assume the port is working. I have tried DFU and recovery to try force syncing to iTunes with no such luck. Any advice as to where to start or what to do?

  • Iphone 4s had 1% i plugged it into charger and it did not charge:

    now it is completely dead when plugged in it displays the battery icon with a slight amount of red on the left but nothing else i have tried multiple charging devices and it will not charge please help

    How long have you had your device because sometimes after quite a whiler the lithium battery dies out..

Maybe you are looking for

  • Provisioning log is not available on Access request type Change Account

    Hi, So I have and issue when I try to submit a request to add a role to a user and I'm trying to understand what could be the reason for it.  Basically I have a workflow that works perfectly for a "Change Request".  I can see that all the steps are e

  • Playlist empty when connected to car system

    Since upgrading to iOS6.0, though the songs in my iTunes playlist show up on my iPhone 4S, whenever I connect the phone to my Hyundai system, the playlist becomes empty. The only songs I can play are the ones that are not in the cloud. Didn't have th

  • Regd. Detailed steps for creating BS,TechSys, SWC etc in SLD

    Hi Experts ! Can some one share a good detailed document on  the steps performed in SLD  like creation of product, software componet and how to create and link the Technical system and business systems. What are the various dependencies to be maintai

  • Symbol Properties

    In Flash, I can programmatically change a Movie Clips properties with ActionScript. How can I do this with Edge? I've tried something like this: sym.getSymbol("ElementA").x = 450; And it doesn't work. Should I be addressing the CSS properties instead

  • Insert rows in the middle

    I'm trying to figure out how to insert rows in the middle row 1 row 2 row 3 I need to insert 2 rows before row 2 I know I have to use the AddRow(1, Position) however after many tries, it doesn't seem to work or at least I don't know how to insert the