Able resume from suspend in Console, but not in xfce

I am testing suspend/Hibernation in my laptop.
When I suspend in console, " sudo pm-suspend --quirk-vbestate-restore " would do the job,  However, if I log in to xfce. the same command will fail to work. It is able to suspend, however can't be resume.
Anyone have any idea why is that happen?
Thanks

What graphics card do you have and which X driver are you using?
I can suspend / resume within a GUI environment, but not a text based environment o_0

Similar Messages

  • Touchpad permanently not working after resuming from suspend

    I lost touchpad and trackpoint functionality after resuming from suspend on my ThinkPad E530 (3259CTO).
    Even after a complete power off (with the battery removed), the touchpad is detected but doesn't send any event, and the trackpoint is not detected.
    In Windows, in the UltraNav control panel, the touchpad is marked as enabled and cannot be disabled, the trackpoint is grayed.
    In Linux, I can see the difference is kernel traces when the driver is loaded.
    Before : psmouse serio1: synaptics: Touchpad model: 1, fw: 8.0, id: 0x1e2b1, caps: 0xd001a3/0x940300/0x120c00
    Now    : psmouse serio1: synaptics: Touchpad model: 1, fw: 8.0, id: 0x1e2b1, caps: 0xd001a3/0x0/0x0
    After looking at https://gerrit.chromium.org/gerrit/#/c/31105/ and Synaptics public documentation, I was able to get more information : the device status register (F01_RMI_Data0) is 0x45, which means the touchpad is in flash programming mode since there is a firmware CRC failure.
    It looks like http://code.google.com/p/chromium-os/issues/detail?id=24298, so it's probably not a Lenovo specific problem, but a bug in Synaptics firmware.
    Can Lenovo provide the firmware to flash like http://forums.lenovo.com/t5/X-Series-ThinkPad-Laptops/X220-Touchpad-jumpy-response-when-used-with-90... which would hopefully make my touchpad working again ?
    The original firmware should work, but an updated one would be better, if it avoids losing the touchpad again later.

     I don't know why, but this made me think of the episode of the simpsons when home tries to get over 300 pounds so he can work from home.  When he tries to dial the phone he hist all the buttons and gets a recording that says "We're sorry, you're fingers are too fat. To obtain a special dialing wand, please mash the keypad now."
    BTW, sorry I can't help... but at least I am entertained easily.

  • Laptop screen not getting locked on close lid or resume from suspend

    I am using kde 4.4 rc2 atm. My laptop screen is not getting locked when I closed the lid or when laptop resumes from a suspend to ram.
    It used to work correctly before I installed acpid(before that I just had the acpi client package installed.) Power Devil used to handle everything correctly.
    The power devil settings already says, Lock screen on resume and I have added Lock screen as action for Lid close for performance profile.
    Is there any way to fix this. I want to make laptop screen lock when I do lid close or resume from suspend/hibernate.

    Suspend has always been problematic under Linux. It seems to be hit or miss for the most part, but here are some things you can try:
    Use an LTS kernel, tuxonice, pm-utils, etc. See Suspend and Hibernate
    Try a different graphics driver
    Tweak the driver module parameters or build your own driver.
    Unfortunately I don't have experience with the radeon driver, so I can only give you ideas.

  • [SOLVED] Cannot resume from suspend but hibernate works fine

    Please help me figuring out what can be the issues..
    I cannot resume from suspend while "sudo pm-hibernate" works fine..
    When I use "sudo pm-suspend", the system (samsung N210 netbook) goes to sleep and I can see the power light blinking as expected. But, when I try to resume the system from suspend by pressing the power button, the screen remains black with no HDD activity. Only thing I can see is the power LED on.
    After I do "sudo pm-suspend" and try to resume from suspend but fails. So, I do a HARD reboot and then this is the content of  /var/log/pm-suspend.log
    Initial commandline parameters:
    Thu Dec 16 12:00:27 IST 2010: Running hooks for suspend.
    Running hook /usr/lib/pm-utils/sleep.d/00logging suspend suspend:
    Linux archlinux-N210 2.6.36-ARCH #1 SMP PREEMPT Fri Dec 10 20:32:37 CET 2010 x86_64 Intel(R) Atom(TM) CPU N450 @ 1.66GHz GenuineIntel GNU/Linux
    Module Size Used by
    dm_mod 66662 0
    rfcomm 34874 4
    sco 8828 2
    bnep 8726 2
    l2cap 42585 16 rfcomm,bnep
    ipv6 281833 24
    nls_utf8 1288 0
    cifs 242984 0
    fscache 39915 1 cifs
    fuse 64259 3
    arc4 1378 2
    snd_seq_dummy 1431 0
    snd_hda_codec_realtek 275887 1
    uvcvideo 61404 0
    videodev 64318 1 uvcvideo
    v4l1_compat 15578 2 uvcvideo,videodev
    ecb 2041 2
    snd_seq_oss 28760 0
    ath9k 80424 0
    joydev 10055 0
    btusb 11385 2
    v4l2_compat_ioctl32 10212 1 videodev
    bluetooth 52419 9 rfcomm,sco,bnep,l2cap,btusb
    snd_seq_midi_event 5436 1 snd_seq_oss
    mac80211 196159 1 ath9k
    ath9k_common 3624 1 ath9k
    ath9k_hw 290909 2 ath9k,ath9k_common
    snd_hda_intel 22285 1
    snd_hda_codec 79384 2 snd_hda_codec_realtek,snd_hda_intel
    ath 8822 2 ath9k,ath9k_hw
    snd_seq 50082 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
    snd_seq_device 5297 3 snd_seq_dummy,snd_seq_oss,snd_seq
    snd_pcm_oss 39221 0
    cfg80211 143110 3 ath9k,mac80211,ath
    snd_hwdep 6110 1 snd_hda_codec
    uhci_hcd 21926 0
    easy_slow_down_manager 3185 0
    snd_mixer_oss 17106 2 snd_pcm_oss
    snd_pcm 71921 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
    snd_timer 19265 2 snd_seq,snd_pcm
    cpufreq_powersave 958 0
    sky2 46293 0
    rfkill 15882 3 bluetooth,cfg80211
    led_class 2331 1 ath9k
    snd 57562 11 snd_hda_codec_realtek,snd_seq_oss,snd_hda_intel,snd_hda_codec,snd_seq,snd_seq_device,snd_pcm_oss,snd_hwdep,snd_mixer_oss,snd_pcm,snd_timer
    psmouse 52592 0
    cpufreq_ondemand 8215 2
    soundcore 5969 2 snd
    ehci_hcd 36988 0
    tpm_tis 7928 0
    shpchp 26453 0
    sg 25652 0
    phc_intel 9527 1
    battery 10231 0
    tpm 10957 1 tpm_tis
    samsung_backlight 2844 0
    serio_raw 4486 0
    snd_page_alloc 7249 2 snd_hda_intel,snd_pcm
    usbcore 137570 5 uvcvideo,btusb,uhci_hcd,ehci_hcd
    ac 3105 0
    pci_hotplug 24319 1 shpchp
    tpm_bios 5505 1 tpm
    i2c_i801 8550 0
    freq_table 2323 2 cpufreq_ondemand,phc_intel
    pcspkr 1819 0
    thermal 12242 0
    evdev 8519 14
    processor 25936 1 phc_intel
    mperf 1243 1 phc_intel
    ext4 313574 1
    mbcache 5722 1 ext4
    jbd2 69002 1 ext4
    crc16 1297 2 l2cap,ext4
    sd_mod 25856 4
    ahci 20353 3
    libahci 17982 1 ahci
    libata 156316 2 ahci,libahci
    scsi_mod 124891 3 sg,sd_mod,libata
    i915 321187 3
    drm_kms_helper 25963 1 i915
    drm 175314 3 i915,drm_kms_helper
    i2c_algo_bit 4911 1 i915
    button 4834 1 i915
    i2c_core 18726 6 videodev,i2c_i801,i915,drm_kms_helper,drm,i2c_algo_bit
    video 19305 1 i915
    output 1940 1 video
    intel_agp 29459 2 i915
    total used free shared buffers cached
    Mem: 2046212 603128 1443084 0 11400 258660
    -/+ buffers/cache: 333068 1713144
    Swap: 2250748 0 2250748
    /usr/lib/pm-utils/sleep.d/00logging suspend suspend: success.
    Running hook /usr/lib/pm-utils/sleep.d/00powersave suspend suspend:
    /usr/lib/pm-utils/sleep.d/00powersave suspend suspend: success.
    Running hook /usr/lib/pm-utils/sleep.d/01grub suspend suspend:
    /usr/lib/pm-utils/sleep.d/01grub suspend suspend: success.
    Running hook /usr/lib/pm-utils/sleep.d/01laptop-mode suspend suspend:
    /usr/lib/pm-utils/sleep.d/01laptop-mode suspend suspend: success.
    Running hook /usr/lib/pm-utils/sleep.d/11netcfg suspend suspend:
    /usr/lib/pm-utils/sleep.d/11netcfg suspend suspend: success.
    Running hook /etc/pm/sleep.d/20_samsung-tools suspend suspend:
    /etc/pm/sleep.d/20_samsung-tools suspend suspend: success.
    Running hook /usr/lib/pm-utils/sleep.d/49bluetooth suspend suspend:
    /usr/lib/pm-utils/sleep.d/49bluetooth suspend suspend: success.
    Running hook /usr/lib/pm-utils/sleep.d/75modules suspend suspend:
    /usr/lib/pm-utils/sleep.d/75modules suspend suspend: success.
    Running hook /usr/lib/pm-utils/sleep.d/90clock suspend suspend:
    /usr/lib/pm-utils/sleep.d/90clock suspend suspend: success.
    Running hook /usr/lib/pm-utils/sleep.d/91wicd suspend suspend:
    /usr/lib/pm-utils/sleep.d/91wicd suspend suspend: success.
    Running hook /usr/lib/pm-utils/sleep.d/94cpufreq suspend suspend:
    /usr/lib/pm-utils/sleep.d/94cpufreq suspend suspend: success.
    Running hook /usr/lib/pm-utils/sleep.d/95led suspend suspend:
    /usr/lib/pm-utils/sleep.d/95led suspend suspend: success.
    Running hook /usr/lib/pm-utils/sleep.d/98video-quirk-db-handler suspend suspend:
    Kernel modesetting video driver detected, not using quirks.
    /usr/lib/pm-utils/sleep.d/98video-quirk-db-handler suspend suspend: success.
    Running hook /usr/lib/pm-utils/sleep.d/99video suspend suspend:
    /usr/lib/pm-utils/sleep.d/99video suspend suspend: success.
    Thu Dec 16 12:00:31 IST 2010: performing suspend
    Since, the last time I checked about suspend was 1.5 months back, I cant really make out as to what package caused the issue as I had a few upgrades since that time.
    I am no expert but it seems like it is the log of suspending the system, it seems like the system didnt even go to initial stage of resuming.
    Last edited by shadyabhi (2010-12-27 17:54:19)

    Well this is a long shot... But my laptop had some issues with suspending due to low-power governors preventing it from fully working at times.
    Because of that I manually suspend with the following script:
    #!/bin/bash
    clear
    cpufreq-set -g performance
    cpufreq-info
    echo "Continue? y/n? ";read bevestiging
    if [ $bevestiging = "y" ]
    then
    echo "System going down for suspension NOW!"
    pm-suspend
    else
    echo "Exiting..."
    exit 0
    fi
    exit 0
    All it really does in the end, is change the governer from which it's currently on to "performance", thus allowing maximum clock speed.
    I've also added in a little confirmation dialog to check whether it's properly switched.
    Of course, this will only work for you if you're also using laptop-mode and cpufrequtils.
    Edit: You need to run this script with sudo or as the root user.
    Last edited by Aeva (2010-12-16 14:16:32)

  • Resume from suspend not working anymore

    Hello,
    until a couple of months suspending and resuming on my system worked flawlessly. Then something happend (I can't remember what I did - system update or a new package most probably) and I didn't have time then to trace.
    I'm running 64-bit archlinux on a SandyBridge i3 processor with onboard graphics and using Gnome3.
    As I was trying to gather some information I found that actually sudo pm-suspend works (when suspending and resuming from a virtual console). When I try to get back to Gnome with Alt + F7 or sudo gdm (if gnome was not running) the system hangs and I must force shutdown with the power button.
    As I am out of ideas and I don't have any experience at tracking errors, can anyone suggest what should I do next?
    Thanks in advance

    Thanks for your quick reply!!
    1) I didn't find anything weird in dmesg.log (or I don't know what to look for)
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Linux version 3.4.9-1-ARCH (tobias@T-POWA-LX) (gcc version 4.7.1 20120721 (prerelease) (GCC) ) #1 SMP PREEMPT Wed Aug 15 18:59:31 CEST 2012
    [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux root=/dev/disk/by-uuid/e1084449-2e1e-4073-b8ce-1cccb4558de0 rootfstype=ext4 ro add_efi_memmap
    [ 0.000000] BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
    [ 0.000000] BIOS-e820: 0000000000100000 - 0000000020000000 (usable)
    [ 0.000000] BIOS-e820: 0000000020000000 - 0000000020200000 (reserved)
    [ 0.000000] BIOS-e820: 0000000020200000 - 0000000040000000 (usable)
    [ 0.000000] BIOS-e820: 0000000040000000 - 0000000040200000 (reserved)
    [ 0.000000] BIOS-e820: 0000000040200000 - 00000000aed8a000 (usable)
    [ 0.000000] BIOS-e820: 00000000aed8a000 - 00000000aeddc000 (ACPI NVS)
    [ 0.000000] BIOS-e820: 00000000aeddc000 - 00000000aee08000 (reserved)
    [ 0.000000] BIOS-e820: 00000000aee08000 - 00000000aee09000 (usable)
    [ 0.000000] BIOS-e820: 00000000aee09000 - 00000000aee0c000 (ACPI NVS)
    [ 0.000000] BIOS-e820: 00000000aee0c000 - 00000000aee0d000 (ACPI data)
    [ 0.000000] BIOS-e820: 00000000aee0d000 - 00000000aee17000 (ACPI NVS)
    [ 0.000000] BIOS-e820: 00000000aee17000 - 00000000aee3c000 (reserved)
    [ 0.000000] BIOS-e820: 00000000aee3c000 - 00000000aee7f000 (ACPI NVS)
    [ 0.000000] BIOS-e820: 00000000aee7f000 - 00000000af000000 (usable)
    [ 0.000000] BIOS-e820: 00000000af800000 - 00000000bfa00000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed40000 (reserved)
    [ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
    [ 0.000000] BIOS-e820: 0000000100000000 - 000000013fe00000 (usable)
    [ 0.000000] NX (Execute Disable) protection: active
    [ 0.000000] efi: EFI v2.00 by American Megatrends
    [ 0.000000] efi: SMBIOS=0xaee3ac98 ACPI=0xaedd4000 ACPI 2.0=0xaedd4000 MPS=0xfcbc0
    [ 0.000000] efi: mem00: type=3, attr=0xf, range=[0x0000000000000000-0x0000000000008000) (0MB)
    [ 0.000000] efi: mem01: type=7, attr=0xf, range=[0x0000000000008000-0x0000000000077000) (0MB)
    [ 0.000000] efi: mem02: type=4, attr=0xf, range=[0x0000000000077000-0x0000000000078000) (0MB)
    [ 0.000000] efi: mem03: type=3, attr=0xf, range=[0x0000000000078000-0x00000000000a0000) (0MB)
    [ 0.000000] efi: mem04: type=2, attr=0xf, range=[0x0000000000100000-0x0000000000435000) (3MB)
    [ 0.000000] efi: mem05: type=7, attr=0xf, range=[0x0000000000435000-0x0000000001000000) (11MB)
    [ 0.000000] efi: mem06: type=2, attr=0xf, range=[0x0000000001000000-0x0000000001100000) (1MB)
    [ 0.000000] efi: mem07: type=4, attr=0xf, range=[0x0000000001100000-0x0000000001338000) (2MB)
    [ 0.000000] efi: mem08: type=3, attr=0xf, range=[0x0000000001338000-0x000000000133a000) (0MB)
    [ 0.000000] efi: mem09: type=4, attr=0xf, range=[0x000000000133a000-0x0000000001351000) (0MB)
    [ 0.000000] efi: mem10: type=3, attr=0xf, range=[0x0000000001351000-0x0000000001355000) (0MB)
    [ 0.000000] efi: mem11: type=4, attr=0xf, range=[0x0000000001355000-0x0000000001383000) (0MB)
    [ 0.000000] efi: mem12: type=3, attr=0xf, range=[0x0000000001383000-0x000000000138b000) (0MB)
    [ 0.000000] efi: mem13: type=4, attr=0xf, range=[0x000000000138b000-0x000000000138c000) (0MB)
    [ 0.000000] efi: mem14: type=3, attr=0xf, range=[0x000000000138c000-0x0000000001395000) (0MB)
    [ 0.000000] efi: mem15: type=4, attr=0xf, range=[0x0000000001395000-0x000000000139d000) (0MB)
    [ 0.000000] efi: mem16: type=3, attr=0xf, range=[0x000000000139d000-0x000000000139e000) (0MB)
    [ 0.000000] efi: mem17: type=4, attr=0xf, range=[0x000000000139e000-0x00000000013a0000) (0MB)
    [ 0.000000] efi: mem18: type=3, attr=0xf, range=[0x00000000013a0000-0x00000000013a4000) (0MB)
    [ 0.000000] efi: mem19: type=4, attr=0xf, range=[0x00000000013a4000-0x00000000013aa000) (0MB)
    [ 0.000000] efi: mem20: type=3, attr=0xf, range=[0x00000000013aa000-0x00000000013ab000) (0MB)
    [ 0.000000] efi: mem21: type=4, attr=0xf, range=[0x00000000013ab000-0x00000000013b7000) (0MB)
    [ 0.000000] efi: mem22: type=3, attr=0xf, range=[0x00000000013b7000-0x00000000013b9000) (0MB)
    [ 0.000000] efi: mem23: type=4, attr=0xf, range=[0x00000000013b9000-0x00000000013bf000) (0MB)
    [ 0.000000] efi: mem24: type=3, attr=0xf, range=[0x00000000013bf000-0x00000000013c7000) (0MB)
    [ 0.000000] efi: mem25: type=4, attr=0xf, range=[0x00000000013c7000-0x00000000013e3000) (0MB)
    [ 0.000000] efi: mem26: type=3, attr=0xf, range=[0x00000000013e3000-0x00000000013fa000) (0MB)
    [ 0.000000] efi: mem27: type=4, attr=0xf, range=[0x00000000013fa000-0x000000000178a000) (3MB)
    [ 0.000000] efi: mem28: type=3, attr=0xf, range=[0x000000000178a000-0x000000000178b000) (0MB)
    [ 0.000000] efi: mem29: type=4, attr=0xf, range=[0x000000000178b000-0x000000000178e000) (0MB)
    [ 0.000000] efi: mem30: type=3, attr=0xf, range=[0x000000000178e000-0x0000000001790000) (0MB)
    [ 0.000000] efi: mem31: type=4, attr=0xf, range=[0x0000000001790000-0x0000000001792000) (0MB)
    [ 0.000000] efi: mem32: type=3, attr=0xf, range=[0x0000000001792000-0x0000000001793000) (0MB)
    [ 0.000000] efi: mem33: type=4, attr=0xf, range=[0x0000000001793000-0x00000000017b1000) (0MB)
    [ 0.000000] efi: mem34: type=3, attr=0xf, range=[0x00000000017b1000-0x00000000017cc000) (0MB)
    [ 0.000000] efi: mem35: type=4, attr=0xf, range=[0x00000000017cc000-0x00000000017d4000) (0MB)
    [ 0.000000] efi: mem36: type=3, attr=0xf, range=[0x00000000017d4000-0x00000000017d6000) (0MB)
    [ 0.000000] efi: mem37: type=4, attr=0xf, range=[0x00000000017d6000-0x00000000017d8000) (0MB)
    [ 0.000000] efi: mem38: type=3, attr=0xf, range=[0x00000000017d8000-0x00000000017da000) (0MB)
    [ 0.000000] efi: mem39: type=4, attr=0xf, range=[0x00000000017da000-0x00000000017de000) (0MB)
    [ 0.000000] efi: mem40: type=3, attr=0xf, range=[0x00000000017de000-0x00000000017e1000) (0MB)
    [ 0.000000] efi: mem41: type=4, attr=0xf, range=[0x00000000017e1000-0x00000000017e5000) (0MB)
    [ 0.000000] efi: mem42: type=3, attr=0xf, range=[0x00000000017e5000-0x00000000017e7000) (0MB)
    [ 0.000000] efi: mem43: type=4, attr=0xf, range=[0x00000000017e7000-0x00000000017ea000) (0MB)
    [ 0.000000] efi: mem44: type=3, attr=0xf, range=[0x00000000017ea000-0x00000000017ec000) (0MB)
    [ 0.000000] efi: mem45: type=4, attr=0xf, range=[0x00000000017ec000-0x00000000017f7000) (0MB)
    [ 0.000000] efi: mem46: type=3, attr=0xf, range=[0x00000000017f7000-0x00000000017f9000) (0MB)
    [ 0.000000] efi: mem47: type=4, attr=0xf, range=[0x00000000017f9000-0x00000000017fc000) (0MB)
    [ 0.000000] efi: mem48: type=3, attr=0xf, range=[0x00000000017fc000-0x0000000001804000) (0MB)
    [ 0.000000] efi: mem49: type=4, attr=0xf, range=[0x0000000001804000-0x000000000180c000) (0MB)
    [ 0.000000] efi: mem50: type=3, attr=0xf, range=[0x000000000180c000-0x000000000180d000) (0MB)
    [ 0.000000] efi: mem51: type=4, attr=0xf, range=[0x000000000180d000-0x000000000180e000) (0MB)
    [ 0.000000] efi: mem52: type=3, attr=0xf, range=[0x000000000180e000-0x0000000001813000) (0MB)
    [ 0.000000] efi: mem53: type=4, attr=0xf, range=[0x0000000001813000-0x0000000001819000) (0MB)
    [ 0.000000] efi: mem54: type=3, attr=0xf, range=[0x0000000001819000-0x000000000181b000) (0MB)
    [ 0.000000] efi: mem55: type=4, attr=0xf, range=[0x000000000181b000-0x000000000181d000) (0MB)
    [ 0.000000] efi: mem56: type=3, attr=0xf, range=[0x000000000181d000-0x0000000001821000) (0MB)
    [ 0.000000] efi: mem57: type=4, attr=0xf, range=[0x0000000001821000-0x0000000001824000) (0MB)
    [ 0.000000] efi: mem58: type=3, attr=0xf, range=[0x0000000001824000-0x0000000001831000) (0MB)
    [ 0.000000] efi: mem59: type=4, attr=0xf, range=[0x0000000001831000-0x0000000001860000) (0MB)
    [ 0.000000] efi: mem60: type=3, attr=0xf, range=[0x0000000001860000-0x0000000001875000) (0MB)
    [ 0.000000] efi: mem61: type=4, attr=0xf, range=[0x0000000001875000-0x000000000188f000) (0MB)
    [ 0.000000] efi: mem62: type=3, attr=0xf, range=[0x000000000188f000-0x000000000189a000) (0MB)
    [ 0.000000] efi: mem63: type=4, attr=0xf, range=[0x000000000189a000-0x000000000189d000) (0MB)
    [ 0.000000] efi: mem64: type=3, attr=0xf, range=[0x000000000189d000-0x00000000018a1000) (0MB)
    [ 0.000000] efi: mem65: type=4, attr=0xf, range=[0x00000000018a1000-0x00000000018a4000) (0MB)
    [ 0.000000] efi: mem66: type=3, attr=0xf, range=[0x00000000018a4000-0x00000000018a6000) (0MB)
    [ 0.000000] efi: mem67: type=4, attr=0xf, range=[0x00000000018a6000-0x00000000018b3000) (0MB)
    [ 0.000000] efi: mem68: type=3, attr=0xf, range=[0x00000000018b3000-0x00000000018b7000) (0MB)
    [ 0.000000] efi: mem69: type=4, attr=0xf, range=[0x00000000018b7000-0x00000000018c0000) (0MB)
    [ 0.000000] efi: mem70: type=3, attr=0xf, range=[0x00000000018c0000-0x00000000018c4000) (0MB)
    [ 0.000000] efi: mem71: type=4, attr=0xf, range=[0x00000000018c4000-0x00000000018c9000) (0MB)
    [ 0.000000] efi: mem72: type=3, attr=0xf, range=[0x00000000018c9000-0x00000000018d2000) (0MB)
    [ 0.000000] efi: mem73: type=4, attr=0xf, range=[0x00000000018d2000-0x00000000018d6000) (0MB)
    [ 0.000000] efi: mem74: type=3, attr=0xf, range=[0x00000000018d6000-0x00000000018da000) (0MB)
    [ 0.000000] efi: mem75: type=4, attr=0xf, range=[0x00000000018da000-0x00000000018dd000) (0MB)
    [ 0.000000] efi: mem76: type=3, attr=0xf, range=[0x00000000018dd000-0x0000000001926000) (0MB)
    [ 0.000000] efi: mem77: type=4, attr=0xf, range=[0x0000000001926000-0x0000000001932000) (0MB)
    [ 0.000000] efi: mem78: type=3, attr=0xf, range=[0x0000000001932000-0x0000000001936000) (0MB)
    [ 0.000000] efi: mem79: type=4, attr=0xf, range=[0x0000000001936000-0x0000000001939000) (0MB)
    [ 0.000000] efi: mem80: type=3, attr=0xf, range=[0x0000000001939000-0x000000000193c000) (0MB)
    [ 0.000000] efi: mem81: type=4, attr=0xf, range=[0x000000000193c000-0x0000000001940000) (0MB)
    [ 0.000000] efi: mem82: type=3, attr=0xf, range=[0x0000000001940000-0x0000000001943000) (0MB)
    [ 0.000000] efi: mem83: type=4, attr=0xf, range=[0x0000000001943000-0x0000000001945000) (0MB)
    [ 0.000000] efi: mem84: type=3, attr=0xf, range=[0x0000000001945000-0x0000000001947000) (0MB)
    [ 0.000000] efi: mem85: type=4, attr=0xf, range=[0x0000000001947000-0x0000000001949000) (0MB)
    [ 0.000000] efi: mem86: type=3, attr=0xf, range=[0x0000000001949000-0x000000000194b000) (0MB)
    [ 0.000000] efi: mem87: type=4, attr=0xf, range=[0x000000000194b000-0x000000000194d000) (0MB)
    [ 0.000000] efi: mem88: type=3, attr=0xf, range=[0x000000000194d000-0x0000000001954000) (0MB)
    [ 0.000000] efi: mem89: type=4, attr=0xf, range=[0x0000000001954000-0x000000000a004000) (134MB)
    [ 0.000000] efi: mem90: type=3, attr=0xf, range=[0x000000000a004000-0x000000000a006000) (0MB)
    [ 0.000000] efi: mem91: type=4, attr=0xf, range=[0x000000000a006000-0x000000000a00c000) (0MB)
    [ 0.000000] efi: mem92: type=3, attr=0xf, range=[0x000000000a00c000-0x000000000a00f000) (0MB)
    [ 0.000000] efi: mem93: type=4, attr=0xf, range=[0x000000000a00f000-0x000000000a017000) (0MB)
    [ 0.000000] efi: mem94: type=3, attr=0xf, range=[0x000000000a017000-0x000000000a01a000) (0MB)
    [ 0.000000] efi: mem95: type=4, attr=0xf, range=[0x000000000a01a000-0x000000000a01c000) (0MB)
    [ 0.000000] efi: mem96: type=3, attr=0xf, range=[0x000000000a01c000-0x000000000a01e000) (0MB)
    [ 0.000000] efi: mem97: type=4, attr=0xf, range=[0x000000000a01e000-0x000000000a020000) (0MB)
    [ 0.000000] efi: mem98: type=3, attr=0xf, range=[0x000000000a020000-0x000000000a022000) (0MB)
    [ 0.000000] efi: mem99: type=4, attr=0xf, range=[0x000000000a022000-0x000000000a028000) (0MB)
    [ 0.000000] efi: mem100: type=3, attr=0xf, range=[0x000000000a028000-0x000000000a02b000) (0MB)
    [ 0.000000] efi: mem101: type=4, attr=0xf, range=[0x000000000a02b000-0x000000000a02d000) (0MB)
    [ 0.000000] efi: mem102: type=3, attr=0xf, range=[0x000000000a02d000-0x000000000a02f000) (0MB)
    [ 0.000000] efi: mem103: type=4, attr=0xf, range=[0x000000000a02f000-0x000000000a031000) (0MB)
    [ 0.000000] efi: mem104: type=3, attr=0xf, range=[0x000000000a031000-0x000000000a033000) (0MB)
    [ 0.000000] efi: mem105: type=4, attr=0xf, range=[0x000000000a033000-0x000000000a037000) (0MB)
    [ 0.000000] efi: mem106: type=3, attr=0xf, range=[0x000000000a037000-0x000000000a039000) (0MB)
    [ 0.000000] efi: mem107: type=4, attr=0xf, range=[0x000000000a039000-0x000000000a048000) (0MB)
    [ 0.000000] efi: mem108: type=3, attr=0xf, range=[0x000000000a048000-0x000000000a04a000) (0MB)
    [ 0.000000] efi: mem109: type=4, attr=0xf, range=[0x000000000a04a000-0x000000000a04f000) (0MB)
    [ 0.000000] efi: mem110: type=3, attr=0xf, range=[0x000000000a04f000-0x000000000a05c000) (0MB)
    [ 0.000000] efi: mem111: type=4, attr=0xf, range=[0x000000000a05c000-0x000000000a05e000) (0MB)
    [ 0.000000] efi: mem112: type=3, attr=0xf, range=[0x000000000a05e000-0x000000000a060000) (0MB)
    [ 0.000000] efi: mem113: type=4, attr=0xf, range=[0x000000000a060000-0x000000000a062000) (0MB)
    [ 0.000000] efi: mem114: type=3, attr=0xf, range=[0x000000000a062000-0x000000000a064000) (0MB)
    [ 0.000000] efi: mem115: type=4, attr=0xf, range=[0x000000000a064000-0x000000000a066000) (0MB)
    [ 0.000000] efi: mem116: type=3, attr=0xf, range=[0x000000000a066000-0x000000000a068000) (0MB)
    [ 0.000000] efi: mem117: type=4, attr=0xf, range=[0x000000000a068000-0x000000000a06c000) (0MB)
    [ 0.000000] efi: mem118: type=3, attr=0xf, range=[0x000000000a06c000-0x000000000a072000) (0MB)
    [ 0.000000] efi: mem119: type=4, attr=0xf, range=[0x000000000a072000-0x000000000a07a000) (0MB)
    [ 0.000000] efi: mem120: type=3, attr=0xf, range=[0x000000000a07a000-0x000000000a07c000) (0MB)
    [ 0.000000] efi: mem121: type=4, attr=0xf, range=[0x000000000a07c000-0x000000000a084000) (0MB)
    [ 0.000000] efi: mem122: type=3, attr=0xf, range=[0x000000000a084000-0x000000000a087000) (0MB)
    [ 0.000000] efi: mem123: type=4, attr=0xf, range=[0x000000000a087000-0x000000000a08f000) (0MB)
    [ 0.000000] efi: mem124: type=3, attr=0xf, range=[0x000000000a08f000-0x000000000a091000) (0MB)
    [ 0.000000] efi: mem125: type=4, attr=0xf, range=[0x000000000a091000-0x000000000a093000) (0MB)
    [ 0.000000] efi: mem126: type=3, attr=0xf, range=[0x000000000a093000-0x000000000a098000) (0MB)
    [ 0.000000] efi: mem127: type=4, attr=0xf, range=[0x000000000a098000-0x000000000a09e000) (0MB)
    [ 0.000000] efi: mem128: type=3, attr=0xf, range=[0x000000000a09e000-0x000000000a0a1000) (0MB)
    [ 0.000000] efi: mem129: type=4, attr=0xf, range=[0x000000000a0a1000-0x000000000a0c1000) (0MB)
    [ 0.000000] efi: mem130: type=3, attr=0xf, range=[0x000000000a0c1000-0x000000000a0d1000) (0MB)
    [ 0.000000] efi: mem131: type=4, attr=0xf, range=[0x000000000a0d1000-0x000000000a3fc000) (3MB)
    [ 0.000000] efi: mem132: type=7, attr=0xf, range=[0x000000000a3fc000-0x000000000a3ff000) (0MB)
    [ 0.000000] efi: mem133: type=4, attr=0xf, range=[0x000000000a3ff000-0x000000000a493000) (0MB)
    [ 0.000000] efi: mem134: type=3, attr=0xf, range=[0x000000000a493000-0x000000000a495000) (0MB)
    [ 0.000000] efi: mem135: type=4, attr=0xf, range=[0x000000000a495000-0x000000000a4b4000) (0MB)
    [ 0.000000] efi: mem136: type=3, attr=0xf, range=[0x000000000a4b4000-0x000000000a4bf000) (0MB)
    [ 0.000000] efi: mem137: type=4, attr=0xf, range=[0x000000000a4bf000-0x000000000a4c9000) (0MB)
    [ 0.000000] efi: mem138: type=7, attr=0xf, range=[0x000000000a4c9000-0x000000000a4cd000) (0MB)
    [ 0.000000] efi: mem139: type=4, attr=0xf, range=[0x000000000a4cd000-0x000000000a5cb000) (0MB)
    [ 0.000000] efi: mem140: type=7, attr=0xf, range=[0x000000000a5cb000-0x000000000a5ec000) (0MB)
    [ 0.000000] efi: mem141: type=1, attr=0xf, range=[0x000000000a5ec000-0x000000000a60d000) (0MB)
    [ 0.000000] efi: mem142: type=7, attr=0xf, range=[0x000000000a60d000-0x000000000a7d0000) (1MB)
    [ 0.000000] efi: mem143: type=4, attr=0xf, range=[0x000000000a7d0000-0x000000000ac40000) (4MB)
    [ 0.000000] efi: mem144: type=7, attr=0xf, range=[0x000000000ac40000-0x0000000020000000) (339MB)
    [ 0.000000] efi: mem145: type=6, attr=0x800000000000000f, range=[0x0000000020000000-0x0000000020200000) (2MB)
    [ 0.000000] efi: mem146: type=7, attr=0xf, range=[0x0000000020200000-0x0000000037a4e000) (376MB)
    [ 0.000000] efi: mem147: type=2, attr=0xf, range=[0x0000000037a4e000-0x0000000037d1f000) (2MB)
    [ 0.000000] efi: mem148: type=7, attr=0xf, range=[0x0000000037d1f000-0x0000000040000000) (130MB)
    [ 0.000000] efi: mem149: type=6, attr=0x800000000000000f, range=[0x0000000040000000-0x0000000040200000) (2MB)
    [ 0.000000] efi: mem150: type=7, attr=0xf, range=[0x0000000040200000-0x00000000859fe000) (1111MB)
    [ 0.000000] efi: mem151: type=2, attr=0xf, range=[0x00000000859fe000-0x00000000aed8a000) (659MB)
    [ 0.000000] efi: mem152: type=10, attr=0xf, range=[0x00000000aed8a000-0x00000000aeddc000) (0MB)
    [ 0.000000] efi: mem153: type=6, attr=0x800000000000000f, range=[0x00000000aeddc000-0x00000000aeddf000) (0MB)
    [ 0.000000] efi: mem154: type=0, attr=0xf, range=[0x00000000aeddf000-0x00000000aee06000) (0MB)
    [ 0.000000] efi: mem155: type=5, attr=0x800000000000000f, range=[0x00000000aee06000-0x00000000aee07000) (0MB)
    [ 0.000000] efi: mem156: type=6, attr=0x800000000000000f, range=[0x00000000aee07000-0x00000000aee08000) (0MB)
    [ 0.000000] efi: mem157: type=7, attr=0xf, range=[0x00000000aee08000-0x00000000aee09000) (0MB)
    [ 0.000000] efi: mem158: type=10, attr=0xf, range=[0x00000000aee09000-0x00000000aee0c000) (0MB)
    [ 0.000000] efi: mem159: type=9, attr=0xf, range=[0x00000000aee0c000-0x00000000aee0d000) (0MB)
    [ 0.000000] efi: mem160: type=10, attr=0xf, range=[0x00000000aee0d000-0x00000000aee17000) (0MB)
    [ 0.000000] efi: mem161: type=5, attr=0x800000000000000f, range=[0x00000000aee17000-0x00000000aee1b000) (0MB)
    [ 0.000000] efi: mem162: type=6, attr=0x800000000000000f, range=[0x00000000aee1b000-0x00000000aee2c000) (0MB)
    [ 0.000000] efi: mem163: type=5, attr=0x800000000000000f, range=[0x00000000aee2c000-0x00000000aee39000) (0MB)
    [ 0.000000] efi: mem164: type=6, attr=0x800000000000000f, range=[0x00000000aee39000-0x00000000aee3c000) (0MB)
    [ 0.000000] efi: mem165: type=10, attr=0xf, range=[0x00000000aee3c000-0x00000000aee7f000) (0MB)
    [ 0.000000] efi: mem166: type=3, attr=0xf, range=[0x00000000aee7f000-0x00000000aeff3000) (1MB)
    [ 0.000000] efi: mem167: type=4, attr=0xf, range=[0x00000000aeff3000-0x00000000aeff6000) (0MB)
    [ 0.000000] efi: mem168: type=3, attr=0xf, range=[0x00000000aeff6000-0x00000000af000000) (0MB)
    [ 0.000000] efi: mem169: type=7, attr=0xf, range=[0x0000000100000000-0x000000013fe00000) (1022MB)
    [ 0.000000] efi: mem170: type=0, attr=0x8000000000000000, range=[0x00000000af800000-0x00000000bfa00000) (258MB)
    [ 0.000000] efi: mem171: type=11, attr=0x8000000000000001, range=[0x00000000fed1c000-0x00000000fed20000) (0MB)
    [ 0.000000] efi: mem172: type=11, attr=0x8000000000000001, range=[0x00000000fed20000-0x00000000fed40000) (0MB)
    [ 0.000000] efi: mem173: type=11, attr=0x8000000000000001, range=[0x00000000ff000000-0x0000000100000000) (16MB)
    [ 0.000000] DMI 2.6 present.
    [ 0.000000] DMI: To Be Filled By O.E.M. To Be Filled By O.E.M./Z68 Pro3-M, BIOS P1.40 07/08/2011
    [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
    [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
    [ 0.000000] No AGP bridge found
    [ 0.000000] last_pfn = 0x13fe00 max_arch_pfn = 0x400000000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-CFFFF write-protect
    [ 0.000000] D0000-DFFFF uncachable
    [ 0.000000] E0000-FFFFF write-through
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 000000000 mask F00000000 write-back
    [ 0.000000] 1 base 100000000 mask FC0000000 write-back
    [ 0.000000] 2 base 0AF800000 mask FFF800000 uncachable
    [ 0.000000] 3 base 0B0000000 mask FF0000000 uncachable
    [ 0.000000] 4 base 0C0000000 mask FC0000000 uncachable
    [ 0.000000] 5 base 13FE00000 mask FFFE00000 uncachable
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] 8 disabled
    [ 0.000000] 9 disabled
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] e820 update range: 00000000af800000 - 0000000100000000 (usable) ==> (reserved)
    [ 0.000000] last_pfn = 0xaf000 max_arch_pfn = 0x400000000
    [ 0.000000] found SMP MP-table at [ffff8800000fce90] fce90
    [ 0.000000] initial memory mapped : 0 - 20000000
    [ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 20480
    [ 0.000000] init_memory_mapping: 0000000000000000-00000000af000000
    [ 0.000000] 0000000000 - 00af000000 page 2M
    [ 0.000000] kernel direct mapping tables up to af000000 @ 1fffc000-20000000
    [ 0.000000] init_memory_mapping: 0000000100000000-000000013fe00000
    [ 0.000000] 0100000000 - 013fe00000 page 2M
    [ 0.000000] kernel direct mapping tables up to 13fe00000 @ aed84000-aed8a000
    [ 0.000000] RAMDISK: 37a4e000 - 37d1f000
    [ 0.000000] ACPI: RSDP 00000000aedd4000 00024 (v02 ALASKA)
    [ 0.000000] ACPI: XSDT 00000000aedd4068 00054 (v01 ALASKA A M I 01072009 AMI 00010013)
    [ 0.000000] ACPI: FACP 00000000aeddb858 000F4 (v04 ALASKA A M I 01072009 AMI 00010013)
    [ 0.000000] ACPI: DSDT 00000000aedd4150 07702 (v02 ALASKA A M I 00000000 INTL 20051117)
    [ 0.000000] ACPI: FACS 00000000aee0ef80 00040
    [ 0.000000] ACPI: APIC 00000000aeddb950 00072 (v03 ALASKA A M I 01072009 AMI 00010013)
    [ 0.000000] ACPI: SSDT 00000000aeddb9c8 00102 (v01 AMICPU PROC 00000001 MSFT 03000001)
    [ 0.000000] ACPI: MCFG 00000000aeddbad0 0003C (v01 ALASKA A M I 01072009 MSFT 00000097)
    [ 0.000000] ACPI: AAFT 00000000aeddbb10 000D3 (v01 ALASKA OEMAAFT 01072009 MSFT 00000097)
    [ 0.000000] ACPI: HPET 00000000aeddbbe8 00038 (v01 ALASKA A M I 01072009 AMI. 00000004)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] No NUMA configuration found
    [ 0.000000] Faking a node at 0000000000000000-000000013fe00000
    [ 0.000000] Initmem setup node 0 0000000000000000-000000013fe00000
    [ 0.000000] NODE_DATA [000000013fdfc000 - 000000013fdfffff]
    [ 0.000000] [ffffea0000000000-ffffea0004ffffff] PMD -> [ffff88013b800000-ffff88013f3fffff] on node 0
    [ 0.000000] Zone PFN ranges:
    [ 0.000000] DMA 0x00000010 -> 0x00001000
    [ 0.000000] DMA32 0x00001000 -> 0x00100000
    [ 0.000000] Normal 0x00100000 -> 0x0013fe00
    [ 0.000000] Movable zone start PFN for each node
    [ 0.000000] Early memory PFN ranges
    [ 0.000000] 0: 0x00000010 -> 0x000000a0
    [ 0.000000] 0: 0x00000100 -> 0x00020000
    [ 0.000000] 0: 0x00020200 -> 0x00040000
    [ 0.000000] 0: 0x00040200 -> 0x000aed8a
    [ 0.000000] 0: 0x000aee08 -> 0x000aee09
    [ 0.000000] 0: 0x000aee7f -> 0x000af000
    [ 0.000000] 0: 0x00100000 -> 0x0013fe00
    [ 0.000000] On node 0 totalpages: 977052
    [ 0.000000] DMA zone: 64 pages used for memmap
    [ 0.000000] DMA zone: 12 pages reserved
    [ 0.000000] DMA zone: 3908 pages, LIFO batch:0
    [ 0.000000] DMA32 zone: 16320 pages used for memmap
    [ 0.000000] DMA32 zone: 695116 pages, LIFO batch:31
    [ 0.000000] Normal zone: 4088 pages used for memmap
    [ 0.000000] Normal zone: 257544 pages, LIFO batch:31
    [ 0.000000] ACPI: PM-Timer IO Port: 0x408
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
    [ 0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
    [ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
    [ 0.000000] PM: Registered nosave memory: 0000000020000000 - 0000000020200000
    [ 0.000000] PM: Registered nosave memory: 0000000040000000 - 0000000040200000
    [ 0.000000] PM: Registered nosave memory: 00000000aed8a000 - 00000000aeddc000
    [ 0.000000] PM: Registered nosave memory: 00000000aeddc000 - 00000000aee08000
    [ 0.000000] PM: Registered nosave memory: 00000000aee09000 - 00000000aee0c000
    [ 0.000000] PM: Registered nosave memory: 00000000aee0c000 - 00000000aee0d000
    [ 0.000000] PM: Registered nosave memory: 00000000aee0d000 - 00000000aee17000
    [ 0.000000] PM: Registered nosave memory: 00000000aee17000 - 00000000aee3c000
    [ 0.000000] PM: Registered nosave memory: 00000000aee3c000 - 00000000aee7f000
    [ 0.000000] PM: Registered nosave memory: 00000000af000000 - 00000000af800000
    [ 0.000000] PM: Registered nosave memory: 00000000af800000 - 00000000bfa00000
    [ 0.000000] PM: Registered nosave memory: 00000000bfa00000 - 00000000fed1c000
    [ 0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed40000
    [ 0.000000] PM: Registered nosave memory: 00000000fed40000 - 00000000ff000000
    [ 0.000000] PM: Registered nosave memory: 00000000ff000000 - 0000000100000000
    [ 0.000000] Allocating PCI resources starting at bfa00000 (gap: bfa00000:3f31c000)
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88013fa00000 s82944 r8192 d23552 u524288
    [ 0.000000] pcpu-alloc: s82944 r8192 d23552 u524288 alloc=1*2097152
    [ 0.000000] pcpu-alloc: [0] 0 1 2 3
    [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 956568
    [ 0.000000] Policy zone: Normal
    [ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=/dev/disk/by-uuid/e1084449-2e1e-4073-b8ce-1cccb4558de0 rootfstype=ext4 ro add_efi_memmap
    [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.000000] xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340
    [ 0.000000] Checking aperture...
    [ 0.000000] No AGP bridge found
    [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
    [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
    [ 0.000000] Memory: 3754180k/5240832k available (4543k kernel code, 1332624k absent, 154028k reserved, 4304k data, 740k init)
    [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] NR_IRQS:4352 nr_irqs:712 16
    [ 0.000000] Extended CMOS year: 2000
    [ 0.000000] Console: colour dummy device 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] allocated 15728640 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] hpet clockevent registered
    [ 0.000000] Fast TSC calibration using PIT
    [ 0.003333] Detected 3092.770 MHz processor.
    [ 0.000001] Calibrating delay loop (skipped), value calculated using timer frequency.. 6188.27 BogoMIPS (lpj=10309233)
    [ 0.000004] pid_max: default: 32768 minimum: 301
    [ 0.000024] init_memory_mapping: 00000000af800000-00000000bfa00000
    [ 0.000026] 00af800000 - 00bfa00000 page 2M
    [ 0.079342] Security Framework initialized
    [ 0.079345] AppArmor: AppArmor disabled by boot time parameter
    [ 0.079541] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
    [ 0.080185] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
    [ 0.080471] Mount-cache hash table entries: 256
    [ 0.080591] Initializing cgroup subsys cpuacct
    [ 0.080593] Initializing cgroup subsys memory
    [ 0.080597] Initializing cgroup subsys devices
    [ 0.080599] Initializing cgroup subsys freezer
    [ 0.080600] Initializing cgroup subsys net_cls
    [ 0.080601] Initializing cgroup subsys blkio
    [ 0.080620] CPU: Physical Processor ID: 0
    [ 0.080621] CPU: Processor Core ID: 0
    [ 0.080625] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
    [ 0.080625] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
    [ 0.080627] mce: CPU supports 7 MCE banks
    [ 0.080636] CPU0: Thermal monitoring enabled (TM1)
    [ 0.080642] using mwait in idle threads.
    [ 0.081556] ACPI: Core revision 20120320
    [ 0.084916] ftrace: allocating 17833 entries in 70 pages
    [ 0.093003] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.125997] CPU0: Intel(R) Core(TM) i3-2105 CPU @ 3.10GHz stepping 07
    [ 0.230294] Performance Events: PEBS fmt1+, 16-deep LBR, SandyBridge events, Intel PMU driver.
    [ 0.230299] PEBS disabled due to CPU errata.
    [ 0.230301] ... version: 3
    [ 0.230301] ... bit width: 48
    [ 0.230302] ... generic registers: 4
    [ 0.230303] ... value mask: 0000ffffffffffff
    [ 0.230304] ... max period: 000000007fffffff
    [ 0.230305] ... fixed-purpose events: 3
    [ 0.230306] ... event mask: 000000070000000f
    [ 0.250355] NMI watchdog: enabled, takes one hw-pmu counter.
    [ 0.270297] Booting Node 0, Processors #1
    [ 0.283526] NMI watchdog: enabled, takes one hw-pmu counter.
    [ 0.293637] #2
    [ 0.306866] NMI watchdog: enabled, takes one hw-pmu counter.
    [ 0.316959] #3 Ok.
    [ 0.330186] NMI watchdog: enabled, takes one hw-pmu counter.
    [ 0.330210] Brought up 4 CPUs
    [ 0.330211] Total of 4 processors activated (24752.08 BogoMIPS).
    [ 0.332745] devtmpfs: initialized
    [ 0.333413] PM: Registering ACPI NVS region [mem 0xaed8a000-0xaeddbfff] (335872 bytes)
    [ 0.333418] PM: Registering ACPI NVS region [mem 0xaee09000-0xaee0bfff] (12288 bytes)
    [ 0.333419] PM: Registering ACPI NVS region [mem 0xaee0d000-0xaee16fff] (40960 bytes)
    [ 0.333421] PM: Registering ACPI NVS region [mem 0xaee3c000-0xaee7efff] (274432 bytes)
    [ 0.333881] NET: Registered protocol family 16
    [ 0.333955] ACPI: bus type pci registered
    [ 0.333997] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.333999] PCI: not using MMCONFIG
    [ 0.334000] PCI: Using configuration type 1 for base access
    [ 0.334351] bio: create slab <bio-0> at 0
    [ 0.334388] ACPI: Added _OSI(Module Device)
    [ 0.334389] ACPI: Added _OSI(Processor Device)
    [ 0.334390] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.334392] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.335133] ACPI: EC: Look up EC in DSDT
    [ 0.335970] ACPI: Executed 1 blocks of module-level executable AML code
    [ 0.337761] ACPI: SSDT 00000000aee0dc18 0038C (v01 AMI IST 00000001 MSFT 03000001)
    [ 0.337968] ACPI: Dynamic OEM Table Load:
    [ 0.337970] ACPI: SSDT (null) 0038C (v01 AMI IST 00000001 MSFT 03000001)
    [ 0.337986] ACPI: SSDT 00000000aee0ee18 00084 (v01 AMI CST 00000001 MSFT 03000001)
    [ 0.338158] ACPI: Dynamic OEM Table Load:
    [ 0.338160] ACPI: SSDT (null) 00084 (v01 AMI CST 00000001 MSFT 03000001)
    [ 0.338495] ACPI: Interpreter enabled
    [ 0.338497] ACPI: (supports S0 S1 S3 S4 S5)
    [ 0.338509] ACPI: Using IOAPIC for interrupt routing
    [ 0.338523] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.338564] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
    [ 0.381551] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
    [ 0.384682] ACPI: No dock devices found.
    [ 0.384684] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    [ 0.384801] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.384911] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
    [ 0.384913] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
    [ 0.384914] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
    [ 0.384916] pci_root PNP0A08:00: host bridge window [mem 0x000c8000-0x000dffff]
    [ 0.384917] pci_root PNP0A08:00: host bridge window [mem 0xbfa00000-0xffffffff]
    [ 0.384921] pci_root PNP0A08:00: ignoring host bridge window [mem 0x000c8000-0x000dffff] (conflicts with Video ROM [mem 0x000c0000-0x000cdbff])
    [ 0.384940] PCI host bridge to bus 0000:00
    [ 0.384942] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
    [ 0.384943] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
    [ 0.384945] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
    [ 0.384946] pci_bus 0000:00: root bus resource [mem 0xbfa00000-0xffffffff]
    [ 0.384953] pci 0000:00:00.0: [8086:0100] type 00 class 0x060000
    [ 0.384982] pci 0000:00:02.0: [8086:0112] type 00 class 0x030000
    [ 0.384990] pci 0000:00:02.0: reg 10: [mem 0xfe000000-0xfe3fffff 64bit]
    [ 0.384995] pci 0000:00:02.0: reg 18: [mem 0xc0000000-0xcfffffff 64bit pref]
    [ 0.384998] pci 0000:00:02.0: reg 20: [io 0xf000-0xf03f]
    [ 0.385057] pci 0000:00:16.0: [8086:1c3a] type 00 class 0x078000
    [ 0.385088] pci 0000:00:16.0: reg 10: [mem 0xfe508000-0xfe50800f 64bit]
    [ 0.385193] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
    [ 0.385238] pci 0000:00:1a.0: [8086:1c2d] type 00 class 0x0c0320
    [ 0.385266] pci 0000:00:1a.0: reg 10: [mem 0xfe507000-0xfe5073ff]
    [ 0.385392] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
    [ 0.385427] pci 0000:00:1b.0: [8086:1c20] type 00 class 0x040300
    [ 0.385448] pci 0000:00:1b.0: reg 10: [mem 0xfe500000-0xfe503fff 64bit]
    [ 0.385547] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 0.385577] pci 0000:00:1c.0: [8086:1c10] type 01 class 0x060400
    [ 0.385690] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 0.385725] pci 0000:00:1c.2: [8086:1c14] type 01 class 0x060400
    [ 0.385839] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
    [ 0.385873] pci 0000:00:1c.4: [8086:244e] type 01 class 0x060401
    [ 0.385986] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
    [ 0.386019] pci 0000:00:1c.5: [8086:1c1a] type 01 class 0x060400
    [ 0.386132] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
    [ 0.386173] pci 0000:00:1d.0: [8086:1c26] type 00 class 0x0c0320
    [ 0.386202] pci 0000:00:1d.0: reg 10: [mem 0xfe506000-0xfe5063ff]
    [ 0.386329] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
    [ 0.386361] pci 0000:00:1f.0: [8086:1c44] type 00 class 0x060100
    [ 0.386527] pci 0000:00:1f.2: [8086:1c02] type 00 class 0x010601
    [ 0.386555] pci 0000:00:1f.2: reg 10: [io 0xf0b0-0xf0b7]
    [ 0.386566] pci 0000:00:1f.2: reg 14: [io 0xf0a0-0xf0a3]
    [ 0.386576] pci 0000:00:1f.2: reg 18: [io 0xf090-0xf097]
    [ 0.386587] pci 0000:00:1f.2: reg 1c: [io 0xf080-0xf083]
    [ 0.386598] pci 0000:00:1f.2: reg 20: [io 0xf060-0xf07f]
    [ 0.386607] pci 0000:00:1f.2: reg 24: [mem 0xfe505000-0xfe5057ff]
    [ 0.386676] pci 0000:00:1f.2: PME# supported from D3hot
    [ 0.386700] pci 0000:00:1f.3: [8086:1c22] type 00 class 0x0c0500
    [ 0.386721] pci 0000:00:1f.3: reg 10: [mem 0xfe504000-0xfe5040ff 64bit]
    [ 0.386750] pci 0000:00:1f.3: reg 20: [io 0xf040-0xf05f]
    [ 0.386848] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
    [ 0.386950] pci 0000:02:00.0: [1b6f:7023] type 00 class 0x0c0330
    [ 0.386983] pci 0000:02:00.0: reg 10: [mem 0xfe400000-0xfe407fff 64bit]
    [ 0.387143] pci 0000:02:00.0: supports D1 D2
    [ 0.387144] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.393607] pci 0000:00:1c.2: PCI bridge to [bus 02-02]
    [ 0.393617] pci 0000:00:1c.2: bridge window [mem 0xfe400000-0xfe4fffff]
    [ 0.393711] pci 0000:03:00.0: [1b21:1080] type 01 class 0x060401
    [ 0.393860] pci 0000:00:1c.4: PCI bridge to [bus 03-04] (subtractive decode)
    [ 0.393874] pci 0000:00:1c.4: bridge window [io 0x0000-0x0cf7] (subtractive decode)
    [ 0.393875] pci 0000:00:1c.4: bridge window [io 0x0d00-0xffff] (subtractive decode)
    [ 0.393877] pci 0000:00:1c.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
    [ 0.393878] pci 0000:00:1c.4: bridge window [mem 0xbfa00000-0xffffffff] (subtractive decode)
    [ 0.394016] pci 0000:03:00.0: PCI bridge to [bus 04-04] (subtractive decode)
    [ 0.394042] pci 0000:03:00.0: bridge window [??? 0x00000000 flags 0x0] (subtractive decode)
    [ 0.394044] pci 0000:03:00.0: bridge window [??? 0x00000000 flags 0x0] (subtractive decode)
    [ 0.394045] pci 0000:03:00.0: bridge window [??? 0x00000000 flags 0x0] (subtractive decode)
    [ 0.394047] pci 0000:03:00.0: bridge window [??? 0x00000000 flags 0x0] (subtractive decode)
    [ 0.394048] pci 0000:03:00.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
    [ 0.394050] pci 0000:03:00.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
    [ 0.394051] pci 0000:03:00.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
    [ 0.394053] pci 0000:03:00.0: bridge window [mem 0xbfa00000-0xffffffff] (subtractive decode)
    [ 0.394153] pci 0000:05:00.0: [10ec:8168] type 00 class 0x020000
    [ 0.394177] pci 0000:05:00.0: reg 10: [io 0xe000-0xe0ff]
    [ 0.394220] pci 0000:05:00.0: reg 18: [mem 0xd0004000-0xd0004fff 64bit pref]
    [ 0.394246] pci 0000:05:00.0: reg 20: [mem 0xd0000000-0xd0003fff 64bit pref]
    [ 0.394361] pci 0000:05:00.0: supports D1 D2
    [ 0.394362] pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.400270] pci 0000:00:1c.5: PCI bridge to [bus 05-05]
    [ 0.400276] pci 0000:00:1c.5: bridge window [io 0xe000-0xefff]
    [ 0.400289] pci 0000:00:1c.5: bridge window [mem 0xd0000000-0xd00fffff 64bit pref]
    [ 0.400326] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    [ 0.400385] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
    [ 0.400402] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
    [ 0.400418] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
    [ 0.400434] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4.PE2P._PRT]
    [ 0.400449] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX5._PRT]
    [ 0.400518] pci0000:00: Requesting ACPI _OSC control (0x1d)
    [ 0.400639] pci0000:00: ACPI _OSC control (0x1c) granted
    [ 0.402717] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    [ 0.402746] ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 10 11 12 14 15)
    [ 0.402774] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 10 11 12 14 15)
    [ 0.402801] ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 10 11 12 14 15)
    [ 0.402829] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
    [ 0.402857] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
    [ 0.402885] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    [ 0.402912] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 14 15)
    [ 0.402970] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.402975] vgaarb: loaded
    [ 0.402975] vgaarb: bridge control possible 0000:00:02.0
    [ 0.402997] PCI: Using ACPI for IRQ routing
    [ 0.413220] PCI: pci_cache_line_size set to 64 bytes
    [ 0.413282] reserve RAM buffer: 00000000aed8a000 - 00000000afffffff
    [ 0.413284] reserve RAM buffer: 00000000aee09000 - 00000000afffffff
    [ 0.413286] reserve RAM buffer: 00000000af000000 - 00000000afffffff
    [ 0.413287] reserve RAM buffer: 000000013fe00000 - 000000013fffffff
    [ 0.413348] NetLabel: Initializing
    [ 0.413349] NetLabel: domain hash size = 128
    [ 0.413350] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.413358] NetLabel: unlabeled traffic allowed by default
    [ 0.413372] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
    [ 0.413377] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
    [ 0.415389] Switching to clocksource hpet
    [ 0.418942] pnp: PnP ACPI init
    [ 0.418954] ACPI: bus type pnp registered
    [ 0.419048] pnp 00:00: [bus 00-ff]
    [ 0.419049] pnp 00:00: [io 0x0cf8-0x0cff]
    [ 0.419051] pnp 00:00: [io 0x0000-0x0cf7 window]
    [ 0.419052] pnp 00:00: [io 0x0d00-0xffff window]
    [ 0.419053] pnp 00:00: [mem 0x000a0000-0x000bffff window]
    [ 0.419055] pnp 00:00: [mem 0x000c8000-0x000dffff window]
    [ 0.419056] pnp 00:00: [mem 0xbfa00000-0xffffffff window]
    [ 0.419057] pnp 00:00: [mem 0x00000000 window]
    [ 0.419096] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
    [ 0.419130] pnp 00:01: [mem 0xfed10000-0xfed19fff]
    [ 0.419131] pnp 00:01: [mem 0xe0000000-0xefffffff]
    [ 0.419132] pnp 00:01: [mem 0xfed90000-0xfed93fff]
    [ 0.419133] pnp 00:01: [mem 0xfed20000-0xfed3ffff]
    [ 0.419134] pnp 00:01: [mem 0xfee00000-0xfee0ffff]
    [ 0.419162] system 00:01: [mem 0xfed10000-0xfed19fff] has been reserved
    [ 0.419164] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved
    [ 0.419165] system 00:01: [mem 0xfed90000-0xfed93fff] has been reserved
    [ 0.419167] system 00:01: [mem 0xfed20000-0xfed3ffff] has been reserved
    [ 0.419168] system 00:01: [mem 0xfee00000-0xfee0ffff] has been reserved
    [ 0.419171] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.419205] pnp 00:02: [io 0x0000-0xffffffffffffffff disabled]
    [ 0.419206] pnp 00:02: [io 0x0290-0x029f]
    [ 0.419209] pnp 00:02: [io 0x0000-0xffffffffffffffff disabled]
    [ 0.419229] system 00:02: [io 0x0290-0x029f] has been reserved
    [ 0.419231] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.419407] pnp 00:03: [io 0x03f0-0x03f5]
    [ 0.419409] pnp 00:03: [io 0x03f7]
    [ 0.419416] pnp 00:03: [irq 6]
    [ 0.419418] pnp 00:03: [dma 2]
    [ 0.419450] pnp 00:03: Plug and Play ACPI device, IDs PNP0700 (active)
    [ 0.419661] pnp 00:04: [io 0x0378-0x037f]
    [ 0.419663] pnp 00:04: [io 0x0778-0x077f]
    [ 0.419667] pnp 00:04: [irq 5]
    [ 0.419668] pnp 00:04: [dma 3]
    [ 0.419746] pnp 00:04: Plug and Play ACPI device, IDs PNP0401 (active)
    [ 0.419865] pnp 00:05: [dma 4]
    [ 0.419866] pnp 00:05: [io 0x0000-0x000f]
    [ 0.419867] pnp 00:05: [io 0x0081-0x0083]
    [ 0.419868] pnp 00:05: [io 0x0087]
    [ 0.419869] pnp 00:05: [io 0x0089-0x008b]
    [ 0.419872] pnp 00:05: [io 0x008f]
    [ 0.419873] pnp 00:05: [io 0x00c0-0x00df]
    [ 0.419887] pnp 00:05: Plug and Play ACPI device, IDs PNP0200 (active)
    [ 0.419893] pnp 00:06: [io 0x0070-0x0071]
    [ 0.419897] pnp 00:06: [irq 8]
    [ 0.419910] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.419914] pnp 00:07: [io 0x0061]
    [ 0.419928] pnp 00:07: Plug and Play ACPI device, IDs PNP0800 (active)
    [ 0.419937] pnp 00:08: [io 0x0010-0x001f]
    [ 0.419938] pnp 00:08: [io 0x0022-0x003f]
    [ 0.419939] pnp 00:08: [io 0x0044-0x005f]
    [ 0.419940] pnp 00:08: [io 0x0062-0x0063]
    [ 0.419941] pnp 00:08: [io 0x0065-0x006f]
    [ 0.419942] pnp 00:08: [io 0x0072-0x007f]
    [ 0.419943] pnp 00:08: [io 0x0080]
    [ 0.419944] pnp 00:08: [io 0x0084-0x0086]
    [ 0.419945] pnp 00:08: [io 0x0088]
    [ 0.419946] pnp 00:08: [io 0x008c-0x008e]
    [ 0.419947] pnp 00:08: [io 0x0090-0x009f]
    [ 0.419949] pnp 00:08: [io 0x00a2-0x00bf]
    [ 0.419950] pnp 00:08: [io 0x00e0-0x00ef]
    [ 0.419951] pnp 00:08: [io 0x04d0-0x04d1]
    [ 0.419973] system 00:08: [io 0x04d0-0x04d1] has been reserved
    [ 0.419975] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.419980] pnp 00:09: [io 0x00f0-0x00ff]
    [ 0.419984] pnp 00:09: [irq 13]
    [ 0.419997] pnp 00:09: Plug and Play ACPI device, IDs PNP0c04 (active)
    [ 0.420153] pnp 00:0a: [io 0x03f8-0x03ff]
    [ 0.420157] pnp 00:0a: [irq 4]
    [ 0.420159] pnp 00:0a: [dma 0 disabled]
    [ 0.420194] pnp 00:0a: Plug and Play ACPI device, IDs PNP0501 (active)
    [ 0.420297] pnp 00:0b: [io 0x0400-0x0453]
    [ 0.420298] pnp 00:0b: [io 0x0458-0x047f]
    [ 0.420299] pnp 00:0b: [io 0x1180-0x119f]
    [ 0.420301] pnp 00:0b: [io 0x0500-0x057f]
    [ 0.420303] pnp 00:0b: [mem 0xfed1c000-0xfed1ffff]
    [ 0.420304] pnp 00:0b: [mem 0xfec00000-0xfecfffff]
    [ 0.420305] pnp 00:0b: [mem 0xfed08000-0xfed08fff]
    [ 0.420306] pnp 00:0b: [mem 0xff000000-0xffffffff]
    [ 0.420328] system 00:0b: [io 0x0400-0x0453] has been reserved
    [ 0.420329] system 00:0b: [io 0x0458-0x047f] has been reserved
    [ 0.420331] system 00:0b: [io 0x1180-0x119f] has been reserved
    [ 0.420332] system 00:0b: [io 0x0500-0x057f] has been reserved
    [ 0.420334] system 00:0b: [mem 0xfed1c000-0xfed1ffff] has been reserved
    [ 0.420336] system 00:0b: [mem 0xfec00000-0xfecfffff] could not be reserved
    [ 0.420337] system 00:0b: [mem 0xfed08000-0xfed08fff] has been reserved
    [ 0.420339] system 00:0b: [mem 0xff000000-0xffffffff] has been reserved
    [ 0.420341] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.420362] pnp 00:0c: [io 0x0454-0x0457]
    [ 0.420384] system 00:0c: [io 0x0454-0x0457] has been reserved
    [ 0.420386] system 00:0c: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
    [ 0.420450] pnp 00:0d: [mem 0xfed00000-0xfed003ff]
    [ 0.420471] pnp 00:0d: Plug and Play ACPI device, IDs PNP0103 (active)
    [ 0.420563] pnp: PnP ACPI: found 14 devices
    [ 0.420564] ACPI: ACPI bus type pnp unregistered
    [ 0.426680] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
    [ 0.426695] pci 0000:00:1c.2: PCI bridge to [bus 02-02]
    [ 0.426701] pci 0000:00:1c.2: bridge window [mem 0xfe400000-0xfe4fffff]
    [ 0.426711] pci 0000:03:00.0: PCI bridge to [bus 04-04]
    [ 0.426735] pci 0000:00:1c.4: PCI bridge to [bus 03-04]
    [ 0.426749] pci 0000:00:1c.5: PCI bridge to [bus 05-05]
    [ 0.426752] pci 0000:00:1c.5: bridge window [io 0xe000-0xefff]
    [ 0.426761] pci 0000:00:1c.5: bridge window [mem 0xd0000000-0xd00fffff 64bit pref]
    [ 0.426802] pci 0000:03:00.0: setting latency timer to 64
    [ 0.426811] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
    [ 0.426813] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
    [ 0.426814] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.426816] pci_bus 0000:00: resource 7 [mem 0xbfa00000-0xffffffff]
    [ 0.426817] pci_bus 0000:02: resource 1 [mem 0xfe400000-0xfe4fffff]
    [ 0.426819] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7]
    [ 0.426820] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff]
    [ 0.426821] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.426823] pci_bus 0000:03: resource 7 [mem 0xbfa00000-0xffffffff]
    [ 0.426824] pci_bus 0000:04: resource 8 [io 0x0000-0x0cf7]
    [ 0.426826] pci_bus 0000:04: resource 9 [io 0x0d00-0xffff]
    [ 0.426827] pci_bus 0000:04: resource 10 [mem 0x000a0000-0x000bffff]
    [ 0.426828] pci_bus 0000:04: resource 11 [mem 0xbfa00000-0xffffffff]
    [ 0.426830] pci_bus 0000:05: resource 0 [io 0xe000-0xefff]
    [ 0.426831] pci_bus 0000:05: resource 2 [mem 0xd0000000-0xd00fffff 64bit pref]
    [ 0.426856] NET: Registered protocol family 2
    [ 0.426935] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
    [ 0.427381] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
    [ 0.428316] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    [ 0.428427] TCP: Hash tables configured (established 524288 bind 65536)
    [ 0.428429] TCP: reno registered
    [ 0.428434] UDP hash table entries: 2048 (order: 4, 65536 bytes)
    [ 0.428446] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
    [ 0.428503] NET: Registered protocol family 1
    [ 0.428513] pci 0000:00:02.0: Boot video device
    [ 0.675460] PCI: CLS 64 bytes, default 64
    [ 0.675493] Unpacking initramfs...
    [ 0.714785] Freeing initrd memory: 2884k freed
    [ 0.715067] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
    [ 0.715071] Placing 64MB software IO TLB between ffff8800aad84000 - ffff8800aed84000
    [ 0.715072] software IO TLB at phys 0xaad84000 - 0xaed84000
    [ 0.715429] audit: initializing netlink socket (disabled)
    [ 0.715441] type=2000 audit(1345564835.613:1): initialized
    [ 0.715668] HugeTLB registered 2 MB page size, pre-allocated 0 pages
    [ 0.716758] VFS: Disk quotas dquot_6.5.2
    [ 0.716785] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [ 0.716842] msgmni has been set to 7361
    [ 0.716962] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
    [ 0.716985] io scheduler noop registered
    [ 0.716987] io scheduler deadline registered
    [ 0.717018] io scheduler cfq registered (default)
    [ 0.717132] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
    [ 0.717265] pcieport 0000:00:1c.2: irq 41 for MSI/MSI-X
    [ 0.717395] pcieport 0000:00:1c.5: irq 42 for MSI/MSI-X
    [ 0.717490] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
    [ 0.717494] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
    [ 0.717512] pcieport 0000:00:1c.2: Signaling PME through PCIe PME interrupt
    [ 0.717514] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
    [ 0.717518] pcie_pme 0000:00:1c.2:pcie01: service driver pcie_pme loaded
    [ 0.717535] pcieport 0000:00:1c.5: Signaling PME through PCIe PME interrupt
    [ 0.717536] pci 0000:05:00.0: Signaling PME through PCIe PME interrupt
    [ 0.717541] pcie_pme 0000:00:1c.5:pcie01: service driver pcie_pme loaded
    [ 0.717599] efifb: probing for efifb
    [ 0.718140] efifb: framebuffer at 0xc0000000, mapped to 0xffffc90012180000, using 3072k, total 3072k
    [ 0.718142] efifb: mode is 1024x768x32, linelength=4096, pages=1
    [ 0.718143] efifb: scrolling: redraw
    [ 0.718144] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
    [ 0.719514] Console: switching to colour frame buffer device 128x48
    [ 0.720791] fb0: EFI VGA frame buffer device
    [ 0.720795] intel_idle: MWAIT substates: 0x1120
    [ 0.720796] intel_idle: v0.4 model 0x2A
    [ 0.720797] intel_idle: lapic_timer_reliable_states 0xffffffff
    [ 0.720820] GHES: HEST is not enabled!
    [ 0.720854] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.741411] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [ 0.762150] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [ 0.762283] Linux agpgart interface v0.103
    [ 0.762329] i8042: PNP: No PS/2 controller found. Probing ports directly.
    [ 0.765011] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 0.765031] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 0.765094] mousedev: PS/2 mouse device common for all mice
    [ 0.765136] rtc_cmos 00:06: RTC can wake from S4
    [ 0.765260] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
    [ 0.765289] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
    [ 0.765337] cpuidle: using governor ladder
    [ 0.765421] cpuidle: using governor menu
    [ 0.765509] TCP: cubic registered
    [ 0.765572] NET: Registered protocol family 10
    [ 0.765685] NET: Registered protocol family 17
    [ 0.765688] Registering the dns_resolver key type
    [ 0.765783] PM: Hibernation image not present or could not be loaded.
    [ 0.765788] registered taskstats version 1
    [ 0.766185] rtc_cmos 00:06: setting system clock to 2012-08-21 16:00:36 UTC (1345564836)
    [ 0.766220] Initializing network drop monitor service
    [ 0.767065] Freeing unused kernel memory: 740k freed
    [ 0.767136] Write protecting the kernel read-only data: 8192k
    [ 0.770282] Freeing unused kernel memory: 1584k freed
    [ 0.771697] Freeing unused kernel memory: 636k freed
    [ 0.776816] systemd-udevd[47]: starting version 188
    [ 0.778195] SCSI subsystem initialized
    [ 0.779045] libata version 3.00 loaded.
    [ 0.779510] ahci 0000:00:1f.2: version 3.0
    [ 0.779577] ahci 0000:00:1f.2: irq 43 for MSI/MSI-X
    [ 0.779608] ahci: SSS flag set, parallel bus scan disabled
    [ 0.792074] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x3f impl SATA mode
    [ 0.792077] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems sxs apst
    [ 0.792082] ahci 0000:00:1f.2: setting latency timer to 64
    [ 0.827616] scsi0 : ahci
    [ 0.827724] scsi1 : ahci
    [ 0.827889] scsi2 : ahci
    [ 0.828042] scsi3 : ahci
    [ 0.828247] scsi4 : ahci
    [ 0.828337] scsi5 : ahci
    [ 0.828577] ata1: SATA max UDMA/133 abar m2048@0xfe505000 port 0xfe505100 irq 43
    [ 0.828580] ata2: SATA max UDMA/133 abar m2048@0xfe505000 port 0xfe505180 irq 43
    [ 0.828583] ata3: SATA max UDMA/133 abar m2048@0xfe505000 port 0xfe505200 irq 43
    [ 0.828586] ata4: SATA max UDMA/133 abar m2048@0xfe505000 port 0xfe505280 irq 43
    [ 0.828589] ata5: SATA max UDMA/133 abar m2048@0xfe505000 port 0xfe505300 irq 43
    [ 0.828592] ata6: SATA max UDMA/133 abar m2048@0xfe505000 port 0xfe505380 irq 43
    [ 1.148643] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
    [ 1.149073] ata1.00: ATA-9: M4-CT064M4SSD2, 0002, max UDMA/100
    [ 1.149078] ata1.00: 125045424 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
    [ 1.149569] ata1.00: configured for UDMA/100
    [ 1.149769] scsi 0:0:0:0: Direct-Access ATA M4-CT064M4SSD2 0002 PQ: 0 ANSI: 5
    [ 1.150512] sd 0:0:0:0: [sda] 125045424 512-byte logical blocks: (64.0 GB/59.6 GiB)
    [ 1.150570] sd 0:0:0:0: [sda] Write Protect is off
    [ 1.150573] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 1.150592] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 1.151977] sda: sda1 sda2 sda3 sda4
    [ 1.152522] sd 0:0:0:0: [sda] Attached SCSI disk
    [ 1.468572] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
    [ 1.470381] ata2.00: ATA-8: WDC WD1002FAEX-00Z3A0, 05.01D05, max UDMA/133
    [ 1.470385] ata2.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
    [ 1.473274] ata2.00: configured for UDMA/133
    [ 1.473458] scsi 1:0:0:0: Direct-Access ATA WDC WD1002FAEX-0 05.0 PQ: 0 ANSI: 5
    [ 1.473563] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
    [ 1.473607] sd 1:0:0:0: [sdb] Write Protect is off
    [ 1.473610] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
    [ 1.473642] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 1.517966] sdb: sdb1 sdb2 sdb3
    [ 1.518466] sd 1:0:0:0: [sdb] Attached SCSI disk
    [ 1.715157] Refined TSC clocksource calibration: 3092.974 MHz.
    [ 1.715163] Switching to clocksource tsc
    [ 1.791820] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [ 1.794693] ata3.00: ATAPI: ATAPI iHBS112 2, CL0K, max UDMA/100
    [ 1.797137] ata3.00: configured for UDMA/100
    [ 1.800652] scsi 2:0:0:0: CD-ROM ATAPI iHBS112 2 CL0K PQ: 0 ANSI: 5
    [ 2.118410] ata4: SATA link down (SStatus 0 SControl 300)
    [ 2.438403] ata5: SATA link down (SStatus 0 SControl 300)
    [ 2.758269] ata6: SATA link down (SStatus 0 SControl 300)
    [ 2.759317] usbcore: registered new interface driver usbfs
    [ 2.759331] usbcore: registered new interface driver hub
    [ 2.759392] usbcore: registered new device driver usb
    [ 2.759767] xhci_hcd 0000:02:00.0: xHCI Host Controller
    [ 2.759783] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 1
    [ 2.759924] xhci_hcd 0000:02:00.0: irq 18, io mem 0xfe400000
    [ 2.760013] xhci_hcd 0000:02:00.0: irq 44 for MSI/MSI-X
    [ 2.760148] xHCI xhci_add_endpoint called for root hub
    [ 2.760149] xHCI xhci_check_bandwidth called for root hub
    [ 2.760166] hub 1-0:1.0: USB hub found
    [ 2.760173] hub 1-0:1.0: 2 ports detected
    [ 2.760241] xhci_hcd 0000:02:00.0: xHCI Host Controller
    [ 2.760246] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 2
    [ 2.760307] xHCI xhci_add_endpoint called for root hub
    [ 2.760308] xHCI xhci_check_bandwidth called for root hub
    [ 2.760325] hub 2-0:1.0: USB hub found
    [ 2.760331] hub 2-0:1.0: 2 ports detected
    [ 2.761902] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 2.761934] ehci_hcd 0000:00:1a.0: setting latency timer to 64
    [ 2.761937] ehci_hcd 0000:00:1a.0: EHCI Host Controller
    [ 2.761943] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
    [ 2.761967] ehci_hcd 0000:00:1a.0: debug port 2
    [ 2.764780] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
    [ 2.764782] cdrom: Uniform CD-ROM driver Revision: 3.20
    [ 2.764953] sr 2:0:0:0: Attached scsi CD-ROM sr0
    [ 2.765846] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
    [ 2.765866] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xfe507000
    [ 2.774911] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
    [ 2.775035] hub 3-0:1.0: USB hub found
    [ 2.775038] hub 3-0:1.0: 2 ports detected
    [ 2.775116] ehci_hcd 0000:00:1d.0: setting latency timer to 64
    [ 2.775119] ehci_hcd 0000:00:1d.0: EHCI Host Controller
    [ 2.775125] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
    [ 2.775148] ehci_hcd 0000:00:1d.0: debug port 2
    [ 2.779024] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
    [ 2.779038] ehci_hcd 0000:00:1d.0: irq 23, io mem 0xfe506000
    [ 2.788249] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
    [ 2.788366] hub 4-0:1.0: USB hub found
    [ 2.788369] hub 4-0:1.0: 2 ports detected
    [ 2.820692] FDC 0 is a post-1991 82077
    [ 2.872787] EXT4-fs (sda3): INFO: recovery required on readonly filesystem
    [ 2.872789] EXT4-fs (sda3): write access will be enabled during recovery
    [ 2.882131] EXT4-fs (sda3): recovery complete
    [ 2.884871] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
    [ 2.982234] systemd-udevd[158]: starting version 188
    [ 3.030910] FS-Cache: Loaded
    [ 3.037531] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
    [ 3.037536] ACPI: Power Button [PWRB]
    [ 3.037571] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
    [ 3.037574] ACPI: Power Button [PWRF]
    [ 3.037734] RPC: Registered named UNIX socket transport module.
    [ 3.037735] RPC: Registered udp transport module.
    [ 3.037736] RPC: Registered tcp transport module.
    [ 3.037737] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [ 3.037768] ACPI: Requesting acpi_cpufreq
    [ 3.046690] NFS: Registering the id_resolver key type
    [ 3.046702] FS-Cache: Netfs 'nfs' registered for caching
    [ 3.048471] parport_pc 00:04: reported by Plug and Play ACPI
    [ 3.048528] parport0: PC-style at 0x378 (0x778), irq 5, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
    [ 3.054887] Linux media interface: v0.10
    [ 3.058479] iTCO_vendor_support: vendor-support=0
    [ 3.058906] mei: module is from the staging directory, the quality is unknown, you have been warned.
    [ 3.059160] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
    [ 3.059273] iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
    [ 3.059907] snd_hda_intel 0000:00:1b.0: enabling device (0000 -> 0002)
    [ 3.059980] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
    [ 3.062446] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 3.063978] input: PC Speaker as /devices/platform/pcspkr/input/input2
    [ 3.064004] Linux video capture interface: v2.00
    [ 3.077833] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
    [ 3.078003] r8169 0000:05:00.0: irq 46 for MSI/MSI-X
    [ 3.078206] r8169 0000:05:00.0: eth0: RTL8168evl/8111evl at 0xffffc900016f2000, 00:25:22:bf:8f:89, XID 0c900800 IRQ 46
    [ 3.078219] r8169 0000:05:00.0: eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
    [ 3.079052] [drm] Initialized drm 1.1.0 20060810
    [ 3.079105] usbcore: registered new interface driver uvcvideo
    [ 3.079108] USB Video Class driver (1.1.1)
    [ 3.081528] usb 3-1: new high-speed USB device number 2 using ehci_hcd
    [ 3.108394] microcode: CPU0 sig=0x206a7, pf=0x2, revision=0x14
    [ 3.129007] ppdev: user-space parallel port driver
    [ 3.138311] microcode: CPU1 sig=0x206a7, pf=0x2, revision=0x14
    [ 3.138894] microcode: CPU2 sig=0x206a7, pf=0x2, revision=0x14
    [ 3.139667] microcode: CPU3 sig=0x206a7, pf=0x2, revision=0x14
    [ 3.140205] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
    [ 3.205474] hub 3-1:1.0: USB hub found
    [ 3.205580] hub 3-1:1.0: 6 ports detected
    [ 3.311473] usb 4-1: new high-speed USB device number 2 using ehci_hcd
    [ 3.435441] hub 4-1:1.0: USB hub found
    [ 3.435515] hub 4-1:1.0: 8 ports detected
    [ 3.621479] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input3
    [ 3.621545] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input4
    [ 3.621591] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
    [ 3.621634] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
    [ 3.621676] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
    [ 3.621716] input: HDA Intel PCH Line Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
    [ 3.621757] input: HDA Intel PCH Line Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
    [ 3.621798] input: HDA Intel PCH Line Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
    [ 3.622331] mei 0000:00:16.0: setting latency timer to 64
    [ 3.622424] mei 0000:00:16.0: irq 47 for MSI/MSI-X
    [ 3.628414] agpgart-intel 0000:00:00.0: Intel Sandybridge Chipset
    [ 3.628609] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
    [ 3.630399] agpgart-intel 0000:00:00.0: detected 262144K stolen memory
    [ 3.630714] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
    [ 3.630744] i801_smbus 0000:00:1f.3: enabling device (0001 -> 0003)
    [ 3.634204] i915 0000:00:02.0: setting latency timer to 64
    [ 3.688532] mtrr: type mismatch for c0000000,10000000 old: write-back new: write-combining
    [ 3.688535] [drm] MTRR allocation failed. Graphics performance may suffer.
    [ 3.688658] i915 0000:00:02.0: irq 48 for MSI/MSI-X
    [ 3.688665] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
    [ 3.688666] [drm] Driver supports precise vblank timestamp query.
    [ 3.688689] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
    [ 3.701451] usb 4-1.1: new full-speed USB device number 3 using ehci_hcd
    [ 3.779653] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
    [ 3.810033] usbcore: registered new interface driver usbhid
    [ 3.810037] usbhid: USB HID core driver
    [ 3.816290] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.0-1.1/input2
    [ 3.818744] input: Logitech Unifying Device. Wireless PID:1024 as /devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.1/4-1.1:1.2/0003:046D:C52B.0003/input/input11
    [ 3.819450] logitech-djdevice 0003:046D:C52B.0004: input,hidraw1: USB HID v1.11 Mouse [Logitech Unifying Device. Wireless PID:1024] on usb-0000:00:1d.0-1.1:1
    [ 3.820990] input: Logitech Unifying Device. Wireless PID:2011 as /devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.1/4-1.1:1.2/0003:046D:C52B.0003/input/input12
    [ 3.821189] logitech-djdevice 0003:046D:C52B.0005: input,hidraw2: USB HID v1.11 Keyboard [Logitech Unifying Device. Wireless PID:2011] on usb-0000:00:1d.0-1.1:2
    [ 3.854791] usb 4-1.2: new high-speed USB device number 4 using ehci_hcd
    [ 4.038403] checking generic (c0000000 300000) vs hw (c0000000 10000000)
    [ 4.038405] fb: conflicting fb hw usage inteldrmfb vs EFI VGA - removing generic driver
    [ 4.038422] Console: switching to colour dummy device 80x25
    [ 4.038941] fbcon: inteldrmfb (fb0) is primary device
    [ 4.157787] uvcvideo: Found UVC 1.00 device <unnamed> (046d:081b)
    [ 4.172102] input: UVC Camera (046d:081b) as /devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.2/4-1.2:1.0/input/input13
    [ 4.201202] Console: switching to colour frame buffer device 240x67
    [ 4.207749] fb0: inteldrmfb frame buffer device
    [ 4.207751] drm: registered panic notifier
    [ 4.207763] No ACPI video bus found
    [ 4.207800] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
    [ 4.238123] usb 4-1.4: new full-speed USB device number 5 using ehci_hcd
    [ 4.357930] Registered IR keymap rc-rc6-mce
    [ 4.358063] input: Media Center Ed. eHome Infrared Remote Transceiver (0471:060c) as /devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.4/4-1.4:1.0/rc/rc0/input14
    [ 4.358178] rc0: Media Center Ed. eHome Infrared Remote Transceiver (0471:060c) as /devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.4/4-1.4:1.0/rc/rc0
    [ 4.359659] IR NEC protocol handler initialized
    [ 4.361116] IR RC5(x) protocol handler initialized
    [ 4.362624] IR RC6 protocol handler initialized
    [ 4.364074] IR JVC protocol handler initialized
    [ 4.365548] IR Sony protocol

  • Problems resuming from suspend on IBM Thinkpad R51

    I have been searching the forums and google for the past several days trying to fix this problem. When I enter suspend through fn+f4 or close the lid, I am unable to resume from suspend status, and must hard shutdown.
    I followed the instructions with my device IDs from this post, https://bbs.archlinux.org/viewtopic.php … 5#p1030435
    This link seems like it might work, but there aren't any of the /etc/sbin/* or /etc/bin/* files  :: http://www.thinkwiki.org/wiki/ACPI_acti … ed_for_R51
    $ lspci -ks 0:02
    00:02.0 VGA compatible controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02)
    Subsystem: IBM Device 0557
    Kernel driver in use: i915
    Kernel modules: i915
    00:02.1 Display controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02)
    Subsystem: IBM Device 0557
    Kernel modules: i915
    $ cat /etc/default/grub
    GRUB_DEFAULT=0
    GRUB_TIMEOUT=5
    GRUB_DISTRIBUTOR="Arch"
    GRUB_CMDLINE_LINUX_DEFAULT="i915.modeset=1"
    GRUB_CMDLINE_LINUX=""
    # Preload both GPT and MBR modules so that they are not missed
    GRUB_PRELOAD_MODULES="part_gpt part_msdos"
    # Uncomment to enable Hidden Menu, and optionally hide the timeout count
    GRUB_HIDDEN_TIMEOUT=0
    #GRUB_HIDDEN_TIMEOUT_QUIET=true
    # Uncomment to use basic console
    GRUB_TERMINAL_INPUT=console
    # Uncomment to disable graphical terminal
    #GRUB_TERMINAL_OUTPUT=console
    # The resolution used on graphical terminal
    # note that you can use only modes which your graphic card supports via VBE
    # you can see them in real GRUB with the command `vbeinfo'
    GRUB_GFXMODE=auto
    # Uncomment to allow the kernel use the same resolution used by grub
    GRUB_GFXPAYLOAD_LINUX=keep
    # Uncomment if you want GRUB to pass to the Linux kernel the old parameter
    # format "root=/dev/xxx" instead of "root=/dev/disk/by-uuid/xxx"
    #GRUB_DISABLE_LINUX_UUID=true
    # Uncomment to disable generation of recovery mode menu entries
    GRUB_DISABLE_RECOVERY=true
    # Uncomment and set to the desired menu colors. Used by normal and wallpaper
    # modes only. Entries specified as foreground/background.
    #GRUB_COLOR_NORMAL="light-blue/black"
    #GRUB_COLOR_HIGHLIGHT="light-cyan/blue"
    # Uncomment one of them for the gfx desired, a image background or a gfxtheme
    #GRUB_BACKGROUND="/path/to/wallpaper"
    #GRUB_THEME="/path/to/gfxtheme"
    # Uncomment to get a beep at GRUB start
    #GRUB_INIT_TUNE="480 440 1"
    #GRUB_SAVEDEFAULT="true"
    $ cat /etc/X11/xorg.conf
    Section "ServerLayout"
    Identifier "X.org Configured"
    Screen 0 "Screen0" 0 0
    Screen 1 "Screen1" RightOf "Screen0"
    Screen 2 "Screen2" RightOf "Screen1"
    Screen 3 "Screen3" RightOf "Screen2"
    InputDevice "Mouse0" "CorePointer"
    InputDevice "Keyboard0" "CoreKeyboard"
    EndSection
    Section "Files"
    ModulePath "/usr/lib/xorg/modules"
    FontPath "/usr/share/fonts/misc/"
    FontPath "/usr/share/fonts/TTF/"
    FontPath "/usr/share/fonts/OTF/"
    FontPath "/usr/share/fonts/Type1/"
    FontPath "/usr/share/fonts/100dpi/"
    FontPath "/usr/share/fonts/75dpi/"
    EndSection
    Section "Module"
    Load "glx"
    EndSection
    Section "InputDevice"
    Identifier "Keyboard0"
    Driver "kbd"
    EndSection
    Section "InputDevice"
    Identifier "Mouse0"
    Driver "mouse"
    Option "Protocol" "auto"
    Option "Device" "/dev/input/mice"
    Option "ZAxisMapping" "4 5 6 7"
    EndSection
    Section "Monitor"
    Identifier "Monitor0"
    VendorName "Monitor Vendor"
    ModelName "Monitor Model"
    EndSection
    Section "Monitor"
    Identifier "Monitor1"
    VendorName "Monitor Vendor"
    ModelName "Monitor Model"
    EndSection
    Section "Monitor"
    Identifier "Monitor2"
    VendorName "Monitor Vendor"
    ModelName "Monitor Model"
    EndSection
    Section "Monitor"
    Identifier "Monitor3"
    VendorName "Monitor Vendor"
    ModelName "Monitor Model"
    EndSection
    Section "Device"
    ### Available Driver options are:-
    ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
    ### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
    ### <percent>: "<f>%"
    ### [arg]: arg optional
    #Option "ShadowFB" # [<bool>]
    #Option "DefaultRefresh" # [<bool>]
    #Option "ModeSetClearScreen" # [<bool>]
    Identifier "Card0"
    Driver "vesa"
    BusID "PCI:0:2:0"
    EndSection
    Section "Device"
    ### Available Driver options are:-
    ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
    ### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
    ### <percent>: "<f>%"
    ### [arg]: arg optional
    #Option "NoAccel" # [<bool>]
    #Option "AccelMethod" # <str>
    #Option "Backlight" # <str>
    #Option "DRI" # <str>
    #Option "ColorKey" # <i>
    #Option "VideoKey" # <i>
    #Option "Tiling" # [<bool>]
    #Option "LinearFramebuffer" # [<bool>]
    #Option "SwapbuffersWait" # [<bool>]
    #Option "TripleBuffer" # [<bool>]
    #Option "XvPreferOverlay" # [<bool>]
    #Option "HotPlug" # [<bool>]
    #Option "RelaxedFencing" # [<bool>]
    #Option "XvMC" # [<bool>]
    #Option "ZaphodHeads" # <str>
    #Option "TearFree" # [<bool>]
    #Option "PerCrtcPixmaps" # [<bool>]
    #Option "FallbackDebug" # [<bool>]
    #Option "DebugFlushBatches" # [<bool>]
    #Option "DebugFlushCaches" # [<bool>]
    #Option "DebugWait" # [<bool>]
    #Option "BufferCache" # [<bool>]
    Identifier "Card1"
    Driver "intel"
    BusID "PCI:0:2:0"
    EndSection
    Section "Device"
    ### Available Driver options are:-
    ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
    ### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
    ### <percent>: "<f>%"
    ### [arg]: arg optional
    #Option "NoAccel" # [<bool>]
    #Option "AccelMethod" # <str>
    #Option "Backlight" # <str>
    #Option "DRI" # <str>
    #Option "ColorKey" # <i>
    #Option "VideoKey" # <i>
    #Option "Tiling" # [<bool>]
    #Option "LinearFramebuffer" # [<bool>]
    #Option "SwapbuffersWait" # [<bool>]
    #Option "TripleBuffer" # [<bool>]
    #Option "XvPreferOverlay" # [<bool>]
    #Option "HotPlug" # [<bool>]
    #Option "RelaxedFencing" # [<bool>]
    #Option "XvMC" # [<bool>]
    #Option "ZaphodHeads" # <str>
    #Option "TearFree" # [<bool>]
    #Option "PerCrtcPixmaps" # [<bool>]
    #Option "FallbackDebug" # [<bool>]
    #Option "DebugFlushBatches" # [<bool>]
    #Option "DebugFlushCaches" # [<bool>]
    #Option "DebugWait" # [<bool>]
    #Option "BufferCache" # [<bool>]
    Identifier "Card2"
    Driver "intel"
    BusID "PCI:0:2:1"
    EndSection
    Section "Device"
    ### Available Driver options are:-
    ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
    ### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
    ### <percent>: "<f>%"
    ### [arg]: arg optional
    #Option "ShadowFB" # [<bool>]
    #Option "Rotate" # <str>
    #Option "fbdev" # <str>
    #Option "debug" # [<bool>]
    Identifier "Card3"
    Driver "fbdev"
    BusID "PCI:0:2:0"
    EndSection
    Section "Screen"
    Identifier "Screen0"
    Device "Card0"
    Monitor "Monitor0"
    SubSection "Display"
    Viewport 0 0
    Depth 1
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 4
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 8
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 15
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 16
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 24
    EndSubSection
    EndSection
    Section "Screen"
    Identifier "Screen1"
    Device "Card1"
    Monitor "Monitor1"
    SubSection "Display"
    Viewport 0 0
    Depth 1
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 4
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 8
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 15
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 16
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 24
    EndSubSection
    EndSection
    Section "Screen"
    Identifier "Screen2"
    Device "Card2"
    Monitor "Monitor2"
    SubSection "Display"
    Viewport 0 0
    Depth 1
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 4
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 8
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 15
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 16
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 24
    EndSubSection
    EndSection
    Section "Screen"
    Identifier "Screen3"
    Device "Card3"
    Monitor "Monitor3"
    SubSection "Display"
    Viewport 0 0
    Depth 1
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 4
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 8
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 15
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 16
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 24
    EndSubSection
    EndSection
    $ cat /etc/X11/xorg.conf.d/20-intel.conf
    Section "Device
    Identifier "card0"
    Driver "intel"
    VendorName "Intel Corporation"
    BoardName "Intel Corporation 82852/855GM Integrated Graphics Device (rev 02)"
    BusID "PCI:0:2:0"
    EndSection
    $ modinfo i915
    filename: /lib/modules/3.9.9-1-ARCH/kernel/drivers/gpu/drm/i915/i915.ko.gz
    license: GPL and additional rights
    description: Intel Graphics
    author: Tungsten Graphics, Inc.
    license: GPL and additional rights
    alias: pci:v00008086d00000155sv*sd*bc03sc*i*
    alias: pci:v00008086d00000157sv*sd*bc03sc*i*
    alias: pci:v00008086d00000F30sv*sd*bc03sc*i*
    alias: pci:v00008086d00000D2Esv*sd*bc03sc*i*
    alias: pci:v00008086d00000D1Esv*sd*bc03sc*i*
    alias: pci:v00008086d00000D0Esv*sd*bc03sc*i*
    alias: pci:v00008086d00000D2Bsv*sd*bc03sc*i*
    alias: pci:v00008086d00000D1Bsv*sd*bc03sc*i*
    alias: pci:v00008086d00000D0Bsv*sd*bc03sc*i*
    alias: pci:v00008086d00000D26sv*sd*bc03sc*i*
    alias: pci:v00008086d00000D16sv*sd*bc03sc*i*
    alias: pci:v00008086d00000D06sv*sd*bc03sc*i*
    alias: pci:v00008086d00000D2Asv*sd*bc03sc*i*
    alias: pci:v00008086d00000D1Asv*sd*bc03sc*i*
    alias: pci:v00008086d00000D0Asv*sd*bc03sc*i*
    alias: pci:v00008086d00000D22sv*sd*bc03sc*i*
    alias: pci:v00008086d00000D12sv*sd*bc03sc*i*
    alias: pci:v00008086d00000D02sv*sd*bc03sc*i*
    alias: pci:v00008086d00000A2Esv*sd*bc03sc*i*
    alias: pci:v00008086d00000A1Esv*sd*bc03sc*i*
    alias: pci:v00008086d00000A0Esv*sd*bc03sc*i*
    alias: pci:v00008086d00000A2Bsv*sd*bc03sc*i*
    alias: pci:v00008086d00000A1Bsv*sd*bc03sc*i*
    alias: pci:v00008086d00000A0Bsv*sd*bc03sc*i*
    alias: pci:v00008086d00000A26sv*sd*bc03sc*i*
    alias: pci:v00008086d00000A16sv*sd*bc03sc*i*
    alias: pci:v00008086d00000A06sv*sd*bc03sc*i*
    alias: pci:v00008086d00000A2Asv*sd*bc03sc*i*
    alias: pci:v00008086d00000A1Asv*sd*bc03sc*i*
    alias: pci:v00008086d00000A0Asv*sd*bc03sc*i*
    alias: pci:v00008086d00000A22sv*sd*bc03sc*i*
    alias: pci:v00008086d00000A12sv*sd*bc03sc*i*
    alias: pci:v00008086d00000A02sv*sd*bc03sc*i*
    alias: pci:v00008086d00000C2Esv*sd*bc03sc*i*
    alias: pci:v00008086d00000C1Esv*sd*bc03sc*i*
    alias: pci:v00008086d00000C0Esv*sd*bc03sc*i*
    alias: pci:v00008086d00000C2Bsv*sd*bc03sc*i*
    alias: pci:v00008086d00000C1Bsv*sd*bc03sc*i*
    alias: pci:v00008086d00000C0Bsv*sd*bc03sc*i*
    alias: pci:v00008086d00000C26sv*sd*bc03sc*i*
    alias: pci:v00008086d00000C16sv*sd*bc03sc*i*
    alias: pci:v00008086d00000C06sv*sd*bc03sc*i*
    alias: pci:v00008086d00000C2Asv*sd*bc03sc*i*
    alias: pci:v00008086d00000C1Asv*sd*bc03sc*i*
    alias: pci:v00008086d00000C0Asv*sd*bc03sc*i*
    alias: pci:v00008086d00000C22sv*sd*bc03sc*i*
    alias: pci:v00008086d00000C12sv*sd*bc03sc*i*
    alias: pci:v00008086d00000C02sv*sd*bc03sc*i*
    alias: pci:v00008086d0000042Esv*sd*bc03sc*i*
    alias: pci:v00008086d0000041Esv*sd*bc03sc*i*
    alias: pci:v00008086d0000040Esv*sd*bc03sc*i*
    alias: pci:v00008086d0000042Bsv*sd*bc03sc*i*
    alias: pci:v00008086d0000041Bsv*sd*bc03sc*i*
    alias: pci:v00008086d0000040Bsv*sd*bc03sc*i*
    alias: pci:v00008086d00000426sv*sd*bc03sc*i*
    alias: pci:v00008086d00000416sv*sd*bc03sc*i*
    alias: pci:v00008086d00000406sv*sd*bc03sc*i*
    alias: pci:v00008086d0000042Asv*sd*bc03sc*i*
    alias: pci:v00008086d0000041Asv*sd*bc03sc*i*
    alias: pci:v00008086d0000040Asv*sd*bc03sc*i*
    alias: pci:v00008086d00000422sv*sd*bc03sc*i*
    alias: pci:v00008086d00000412sv*sd*bc03sc*i*
    alias: pci:v00008086d00000402sv*sd*bc03sc*i*
    alias: pci:v00008086d0000016Asv*sd*bc03sc*i*
    alias: pci:v00008086d0000015Asv*sd*bc03sc*i*
    alias: pci:v00008086d00000162sv*sd*bc03sc*i*
    alias: pci:v00008086d00000152sv*sd*bc03sc*i*
    alias: pci:v00008086d00000166sv*sd*bc03sc*i*
    alias: pci:v00008086d00000156sv*sd*bc03sc*i*
    alias: pci:v00008086d0000010Asv*sd*bc03sc*i*
    alias: pci:v00008086d00000126sv*sd*bc03sc*i*
    alias: pci:v00008086d00000116sv*sd*bc03sc*i*
    alias: pci:v00008086d00000106sv*sd*bc03sc*i*
    alias: pci:v00008086d00000122sv*sd*bc03sc*i*
    alias: pci:v00008086d00000112sv*sd*bc03sc*i*
    alias: pci:v00008086d00000102sv*sd*bc03sc*i*
    alias: pci:v00008086d00000046sv*sd*bc03sc*i*
    alias: pci:v00008086d00000042sv*sd*bc03sc*i*
    alias: pci:v00008086d0000A011sv*sd*bc03sc*i*
    alias: pci:v00008086d0000A001sv*sd*bc03sc*i*
    alias: pci:v00008086d00002E92sv*sd*bc03sc*i*
    alias: pci:v00008086d00002E42sv*sd*bc03sc*i*
    alias: pci:v00008086d00002E32sv*sd*bc03sc*i*
    alias: pci:v00008086d00002E22sv*sd*bc03sc*i*
    alias: pci:v00008086d00002E12sv*sd*bc03sc*i*
    alias: pci:v00008086d00002E02sv*sd*bc03sc*i*
    alias: pci:v00008086d00002A42sv*sd*bc03sc*i*
    alias: pci:v00008086d00002A12sv*sd*bc03sc*i*
    alias: pci:v00008086d00002A02sv*sd*bc03sc*i*
    alias: pci:v00008086d000029D2sv*sd*bc03sc*i*
    alias: pci:v00008086d000029C2sv*sd*bc03sc*i*
    alias: pci:v00008086d000029B2sv*sd*bc03sc*i*
    alias: pci:v00008086d000029A2sv*sd*bc03sc*i*
    alias: pci:v00008086d00002992sv*sd*bc03sc*i*
    alias: pci:v00008086d00002982sv*sd*bc03sc*i*
    alias: pci:v00008086d00002972sv*sd*bc03sc*i*
    alias: pci:v00008086d000027AEsv*sd*bc03sc*i*
    alias: pci:v00008086d000027A2sv*sd*bc03sc*i*
    alias: pci:v00008086d00002772sv*sd*bc03sc*i*
    alias: pci:v00008086d00002592sv*sd*bc03sc*i*
    alias: pci:v00008086d0000258Asv*sd*bc03sc*i*
    alias: pci:v00008086d00002582sv*sd*bc03sc*i*
    alias: pci:v00008086d00002572sv*sd*bc03sc*i*
    alias: pci:v00008086d0000358Esv*sd*bc03sc*i*
    alias: pci:v00008086d00003582sv*sd*bc03sc*i*
    alias: pci:v00008086d00002562sv*sd*bc03sc*i*
    alias: pci:v00008086d00003577sv*sd*bc03sc*i*
    depends: drm_kms_helper,drm,intel-gtt,i2c-core,video,button,i2c-algo-bit,intel-agp
    intree: Y
    vermagic: 3.9.9-1-ARCH SMP preempt mod_unload modversions 686
    parm: invert_brightness:Invert backlight brightness (-1 force normal, 0 machine defaults, 1 force inversion), please report PCI device ID, subsystem vendor and subsystem device ID to [email protected], if your machine needs it. It will then be included in an upcoming module version. (int)
    parm: modeset:Use kernel modesetting [KMS] (0=DRM_I915_KMS from .config, 1=on, -1=force vga console preference [default]) (int)
    parm: fbpercrtc:int
    parm: panel_ignore_lid:Override lid status (0=autodetect, 1=autodetect disabled [default], -1=force lid closed, -2=force lid open) (int)
    parm: powersave:Enable powersavings, fbc, downclocking, etc. (default: true) (int)
    parm: semaphores:Use semaphores for inter-ring sync (default: -1 (use per-chip defaults)) (int)
    parm: i915_enable_rc6:Enable power-saving render C-state 6. Different stages can be selected via bitmask values (0 = disable; 1 = enable rc6; 2 = enable deep rc6; 4 = enable deepest rc6). For example, 3 would enable rc6 and deep rc6, and 7 would enable everything. default: -1 (use per-chip default) (int)
    parm: i915_enable_fbc:Enable frame buffer compression for power savings (default: -1 (use per-chip default)) (int)
    parm: lvds_downclock:Use panel (LVDS/eDP) downclocking for power savings (default: false) (int)
    parm: lvds_channel_mode:Specify LVDS channel mode (0=probe BIOS [default], 1=single-channel, 2=dual-channel) (int)
    parm: lvds_use_ssc:Use Spread Spectrum Clock with panels [LVDS/eDP] (default: auto from VBT) (int)
    parm: vbt_sdvo_panel_type:Override/Ignore selection of SDVO panel mode in the VBT (-2=ignore, -1=auto [default], index in VBT BIOS table) (int)
    parm: reset:Attempt GPU resets (default: true) (bool)
    parm: enable_hangcheck:Periodically check GPU activity for detecting hangs. WARNING: Disabling this can cause system wide hangs. (default: true) (bool)
    parm: i915_enable_ppgtt:Enable PPGTT (default: true) (int)
    parm: preliminary_hw_support:Enable preliminary hardware support. Enable Haswell and ValleyView Support. (default: false) (int)
    parm: disable_power_well:Disable the power well when possible (default: false) (int)
    $ zcat /proc/config.gz
    # Automatically generated file; DO NOT EDIT.
    # Linux/x86 3.9.9-1 Kernel Configuration
    # CONFIG_64BIT is not set
    CONFIG_X86_32=y
    CONFIG_X86=y
    CONFIG_INSTRUCTION_DECODER=y
    CONFIG_OUTPUT_FORMAT="elf32-i386"
    CONFIG_ARCH_DEFCONFIG="arch/x86/configs/i386_defconfig"
    CONFIG_LOCKDEP_SUPPORT=y
    CONFIG_STACKTRACE_SUPPORT=y
    CONFIG_HAVE_LATENCYTOP_SUPPORT=y
    CONFIG_MMU=y
    CONFIG_NEED_DMA_MAP_STATE=y
    CONFIG_NEED_SG_DMA_LENGTH=y
    CONFIG_GENERIC_ISA_DMA=y
    CONFIG_GENERIC_BUG=y
    CONFIG_GENERIC_HWEIGHT=y
    CONFIG_GENERIC_GPIO=y
    CONFIG_ARCH_MAY_HAVE_PC_FDC=y
    CONFIG_RWSEM_XCHGADD_ALGORITHM=y
    CONFIG_GENERIC_CALIBRATE_DELAY=y
    CONFIG_ARCH_HAS_CPU_RELAX=y
    CONFIG_ARCH_HAS_DEFAULT_IDLE=y
    CONFIG_ARCH_HAS_CACHE_LINE_SIZE=y
    CONFIG_ARCH_HAS_CPU_AUTOPROBE=y
    CONFIG_HAVE_SETUP_PER_CPU_AREA=y
    CONFIG_NEED_PER_CPU_EMBED_FIRST_CHUNK=y
    CONFIG_NEED_PER_CPU_PAGE_FIRST_CHUNK=y
    CONFIG_ARCH_HIBERNATION_POSSIBLE=y
    CONFIG_ARCH_SUSPEND_POSSIBLE=y
    # CONFIG_ZONE_DMA32 is not set
    # CONFIG_AUDIT_ARCH is not set
    CONFIG_ARCH_SUPPORTS_OPTIMIZED_INLINING=y
    CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
    CONFIG_HAVE_INTEL_TXT=y
    CONFIG_X86_32_SMP=y
    CONFIG_X86_HT=y
    CONFIG_ARCH_HWEIGHT_CFLAGS="-fcall-saved-ecx -fcall-saved-edx"
    CONFIG_ARCH_CPU_PROBE_RELEASE=y
    CONFIG_ARCH_SUPPORTS_UPROBES=y
    CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
    CONFIG_IRQ_WORK=y
    CONFIG_BUILDTIME_EXTABLE_SORT=y
    # General setup
    CONFIG_INIT_ENV_ARG_LIMIT=32
    CONFIG_CROSS_COMPILE=""
    CONFIG_LOCALVERSION="-ARCH"
    CONFIG_LOCALVERSION_AUTO=y
    CONFIG_HAVE_KERNEL_GZIP=y
    CONFIG_HAVE_KERNEL_BZIP2=y
    CONFIG_HAVE_KERNEL_LZMA=y
    CONFIG_HAVE_KERNEL_XZ=y
    CONFIG_HAVE_KERNEL_LZO=y
    CONFIG_KERNEL_GZIP=y
    # CONFIG_KERNEL_BZIP2 is not set
    # CONFIG_KERNEL_LZMA is not set
    # CONFIG_KERNEL_XZ is not set
    # CONFIG_KERNEL_LZO is not set
    CONFIG_DEFAULT_HOSTNAME="(none)"
    CONFIG_SWAP=y
    CONFIG_SYSVIPC=y
    CONFIG_SYSVIPC_SYSCTL=y
    CONFIG_POSIX_MQUEUE=y
    CONFIG_POSIX_MQUEUE_SYSCTL=y
    CONFIG_FHANDLE=y
    CONFIG_AUDIT=y
    CONFIG_AUDITSYSCALL=y
    CONFIG_AUDIT_WATCH=y
    CONFIG_AUDIT_TREE=y
    CONFIG_AUDIT_LOGINUID_IMMUTABLE=y
    CONFIG_HAVE_GENERIC_HARDIRQS=y
    # IRQ subsystem
    CONFIG_GENERIC_HARDIRQS=y
    CONFIG_GENERIC_IRQ_PROBE=y
    CONFIG_GENERIC_IRQ_SHOW=y
    CONFIG_GENERIC_PENDING_IRQ=y
    CONFIG_IRQ_DOMAIN=y
    # CONFIG_IRQ_DOMAIN_DEBUG is not set
    CONFIG_IRQ_FORCED_THREADING=y
    CONFIG_SPARSE_IRQ=y
    CONFIG_CLOCKSOURCE_WATCHDOG=y
    CONFIG_KTIME_SCALAR=y
    CONFIG_GENERIC_CLOCKEVENTS=y
    CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
    CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
    CONFIG_GENERIC_CLOCKEVENTS_MIN_ADJUST=y
    CONFIG_GENERIC_CMOS_UPDATE=y
    # Timers subsystem
    CONFIG_TICK_ONESHOT=y
    CONFIG_NO_HZ=y
    CONFIG_HIGH_RES_TIMERS=y
    # CPU/Task time and stats accounting
    CONFIG_TICK_CPU_ACCOUNTING=y
    # CONFIG_IRQ_TIME_ACCOUNTING is not set
    CONFIG_BSD_PROCESS_ACCT=y
    CONFIG_BSD_PROCESS_ACCT_V3=y
    CONFIG_TASKSTATS=y
    CONFIG_TASK_DELAY_ACCT=y
    CONFIG_TASK_XACCT=y
    CONFIG_TASK_IO_ACCOUNTING=y
    # RCU Subsystem
    CONFIG_TREE_PREEMPT_RCU=y
    CONFIG_PREEMPT_RCU=y
    CONFIG_RCU_STALL_COMMON=y
    CONFIG_RCU_FANOUT=32
    CONFIG_RCU_FANOUT_LEAF=16
    # CONFIG_RCU_FANOUT_EXACT is not set
    CONFIG_RCU_FAST_NO_HZ=y
    # CONFIG_TREE_RCU_TRACE is not set
    # CONFIG_RCU_BOOST is not set
    CONFIG_RCU_NOCB_CPU=y
    CONFIG_IKCONFIG=y
    CONFIG_IKCONFIG_PROC=y
    CONFIG_LOG_BUF_SHIFT=19
    CONFIG_HAVE_UNSTABLE_SCHED_CLOCK=y
    CONFIG_ARCH_SUPPORTS_NUMA_BALANCING=y
    CONFIG_ARCH_WANTS_PROT_NUMA_PROT_NONE=y
    CONFIG_CGROUPS=y
    # CONFIG_CGROUP_DEBUG is not set
    CONFIG_CGROUP_FREEZER=y
    CONFIG_CGROUP_DEVICE=y
    CONFIG_CPUSETS=y
    CONFIG_PROC_PID_CPUSET=y
    CONFIG_CGROUP_CPUACCT=y
    CONFIG_RESOURCE_COUNTERS=y
    CONFIG_MEMCG=y
    CONFIG_MEMCG_SWAP=y
    # CONFIG_MEMCG_SWAP_ENABLED is not set
    CONFIG_MEMCG_KMEM=y
    # CONFIG_CGROUP_HUGETLB is not set
    # CONFIG_CGROUP_PERF is not set
    CONFIG_CGROUP_SCHED=y
    CONFIG_FAIR_GROUP_SCHED=y
    CONFIG_CFS_BANDWIDTH=y
    CONFIG_RT_GROUP_SCHED=y
    CONFIG_BLK_CGROUP=y
    # CONFIG_DEBUG_BLK_CGROUP is not set
    # CONFIG_CHECKPOINT_RESTORE is not set
    CONFIG_NAMESPACES=y
    CONFIG_UTS_NS=y
    CONFIG_IPC_NS=y
    CONFIG_PID_NS=y
    CONFIG_NET_NS=y
    CONFIG_SCHED_AUTOGROUP=y
    CONFIG_MM_OWNER=y
    # CONFIG_SYSFS_DEPRECATED is not set
    CONFIG_RELAY=y
    CONFIG_BLK_DEV_INITRD=y
    CONFIG_INITRAMFS_SOURCE=""
    CONFIG_RD_GZIP=y
    CONFIG_RD_BZIP2=y
    CONFIG_RD_LZMA=y
    CONFIG_RD_XZ=y
    CONFIG_RD_LZO=y
    # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
    CONFIG_SYSCTL=y
    CONFIG_ANON_INODES=y
    # CONFIG_EXPERT is not set
    CONFIG_HAVE_UID16=y
    CONFIG_UID16=y
    # CONFIG_SYSCTL_SYSCALL is not set
    CONFIG_SYSCTL_EXCEPTION_TRACE=y
    CONFIG_KALLSYMS=y
    # CONFIG_KALLSYMS_ALL is not set
    CONFIG_HOTPLUG=y
    CONFIG_PRINTK=y
    CONFIG_BUG=y
    CONFIG_ELF_CORE=y
    CONFIG_PCSPKR_PLATFORM=y
    CONFIG_HAVE_PCSPKR_PLATFORM=y
    CONFIG_BASE_FULL=y
    CONFIG_FUTEX=y
    CONFIG_EPOLL=y
    CONFIG_SIGNALFD=y
    CONFIG_TIMERFD=y
    CONFIG_EVENTFD=y
    CONFIG_SHMEM=y
    CONFIG_AIO=y
    # CONFIG_EMBEDDED is not set
    CONFIG_HAVE_PERF_EVENTS=y
    # Kernel Performance Events And Counters
    CONFIG_PERF_EVENTS=y
    # CONFIG_DEBUG_PERF_USE_VMALLOC is not set
    CONFIG_VM_EVENT_COUNTERS=y
    CONFIG_PCI_QUIRKS=y
    CONFIG_SLUB_DEBUG=y
    # CONFIG_COMPAT_BRK is not set
    # CONFIG_SLAB is not set
    CONFIG_SLUB=y
    CONFIG_PROFILING=y
    CONFIG_TRACEPOINTS=y
    CONFIG_OPROFILE=m
    # CONFIG_OPROFILE_EVENT_MULTIPLEX is not set
    CONFIG_HAVE_OPROFILE=y
    CONFIG_OPROFILE_NMI_TIMER=y
    CONFIG_KPROBES=y
    CONFIG_JUMP_LABEL=y
    CONFIG_KPROBES_ON_FTRACE=y
    CONFIG_UPROBES=y
    # CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
    CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
    CONFIG_ARCH_USE_BUILTIN_BSWAP=y
    CONFIG_KRETPROBES=y
    CONFIG_USER_RETURN_NOTIFIER=y
    CONFIG_HAVE_IOREMAP_PROT=y
    CONFIG_HAVE_KPROBES=y
    CONFIG_HAVE_KRETPROBES=y
    CONFIG_HAVE_OPTPROBES=y
    CONFIG_HAVE_KPROBES_ON_FTRACE=y
    CONFIG_HAVE_ARCH_TRACEHOOK=y
    CONFIG_HAVE_DMA_ATTRS=y
    CONFIG_HAVE_DMA_CONTIGUOUS=y
    CONFIG_USE_GENERIC_SMP_HELPERS=y
    CONFIG_GENERIC_SMP_IDLE_THREAD=y
    CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
    CONFIG_HAVE_DMA_API_DEBUG=y
    CONFIG_HAVE_HW_BREAKPOINT=y
    CONFIG_HAVE_MIXED_BREAKPOINTS_REGS=y
    CONFIG_HAVE_USER_RETURN_NOTIFIER=y
    CONFIG_HAVE_PERF_EVENTS_NMI=y
    CONFIG_HAVE_PERF_REGS=y
    CONFIG_HAVE_PERF_USER_STACK_DUMP=y
    CONFIG_HAVE_ARCH_JUMP_LABEL=y
    CONFIG_ARCH_HAVE_NMI_SAFE_CMPXCHG=y
    CONFIG_HAVE_ALIGNED_STRUCT_PAGE=y
    CONFIG_HAVE_CMPXCHG_LOCAL=y
    CONFIG_HAVE_CMPXCHG_DOUBLE=y
    CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
    CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
    CONFIG_SECCOMP_FILTER=y
    CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
    CONFIG_HAVE_ARCH_TRANSPARENT_HUGEPAGE=y
    CONFIG_MODULES_USE_ELF_REL=y
    CONFIG_CLONE_BACKWARDS=y
    CONFIG_OLD_SIGSUSPEND3=y
    CONFIG_OLD_SIGACTION=y
    # GCOV-based kernel profiling
    # CONFIG_GCOV_KERNEL is not set
    CONFIG_HAVE_GENERIC_DMA_COHERENT=y
    CONFIG_SLABINFO=y
    CONFIG_RT_MUTEXES=y
    CONFIG_BASE_SMALL=0
    CONFIG_MODULES=y
    CONFIG_MODULE_FORCE_LOAD=y
    CONFIG_MODULE_UNLOAD=y
    CONFIG_MODULE_FORCE_UNLOAD=y
    CONFIG_MODVERSIONS=y
    # CONFIG_MODULE_SRCVERSION_ALL is not set
    # CONFIG_MODULE_SIG is not set
    CONFIG_STOP_MACHINE=y
    CONFIG_BLOCK=y
    CONFIG_LBDAF=y
    CONFIG_BLK_DEV_BSG=y
    CONFIG_BLK_DEV_BSGLIB=y
    # CONFIG_BLK_DEV_INTEGRITY is not set
    CONFIG_BLK_DEV_THROTTLING=y
    # Partition Types
    CONFIG_PARTITION_ADVANCED=y
    # CONFIG_ACORN_PARTITION is not set
    # CONFIG_OSF_PARTITION is not set
    # CONFIG_AMIGA_PARTITION is not set
    # CONFIG_ATARI_PARTITION is not set
    CONFIG_MAC_PARTITION=y
    CONFIG_MSDOS_PARTITION=y
    CONFIG_BSD_DISKLABEL=y
    CONFIG_MINIX_SUBPARTITION=y
    CONFIG_SOLARIS_X86_PARTITION=y
    # CONFIG_UNIXWARE_DISKLABEL is not set
    CONFIG_LDM_PARTITION=y
    # CONFIG_LDM_DEBUG is not set
    # CONFIG_SGI_PARTITION is not set
    # CONFIG_ULTRIX_PARTITION is not set
    # CONFIG_SUN_PARTITION is not set
    CONFIG_KARMA_PARTITION=y
    CONFIG_EFI_PARTITION=y
    # CONFIG_SYSV68_PARTITION is not set
    # IO Schedulers
    CONFIG_IOSCHED_NOOP=y
    CONFIG_IOSCHED_DEADLINE=y
    CONFIG_IOSCHED_CFQ=y
    CONFIG_CFQ_GROUP_IOSCHED=y
    # CONFIG_DEFAULT_DEADLINE is not set
    CONFIG_DEFAULT_CFQ=y
    # CONFIG_DEFAULT_NOOP is not set
    CONFIG_DEFAULT_IOSCHED="cfq"
    CONFIG_PREEMPT_NOTIFIERS=y
    CONFIG_PADATA=y
    CONFIG_ASN1=m
    CONFIG_UNINLINE_SPIN_UNLOCK=y
    CONFIG_FREEZER=y
    # Processor type and features
    CONFIG_ZONE_DMA=y
    CONFIG_SMP=y
    CONFIG_X86_MPPARSE=y
    # CONFIG_X86_BIGSMP is not set
    # CONFIG_X86_EXTENDED_PLATFORM is not set
    # CONFIG_X86_GOLDFISH is not set
    # CONFIG_X86_INTEL_LPSS is not set
    CONFIG_X86_SUPPORTS_MEMORY_FAILURE=y
    CONFIG_X86_32_IRIS=m
    CONFIG_SCHED_OMIT_FRAME_POINTER=y
    CONFIG_PARAVIRT_GUEST=y
    CONFIG_PARAVIRT_TIME_ACCOUNTING=y
    # CONFIG_XEN_PRIVILEGED_GUEST is not set
    CONFIG_KVM_GUEST=y
    CONFIG_LGUEST_GUEST=y
    CONFIG_PARAVIRT=y
    # CONFIG_PARAVIRT_SPINLOCKS is not set
    CONFIG_PARAVIRT_CLOCK=y
    # CONFIG_PARAVIRT_DEBUG is not set
    CONFIG_NO_BOOTMEM=y
    # CONFIG_MEMTEST is not set
    # CONFIG_M486 is not set
    # CONFIG_M586 is not set
    # CONFIG_M586TSC is not set
    # CONFIG_M586MMX is not set
    CONFIG_M686=y
    # CONFIG_MPENTIUMII is not set
    # CONFIG_MPENTIUMIII is not set
    # CONFIG_MPENTIUMM is not set
    # CONFIG_MPENTIUM4 is not set
    # CONFIG_MK6 is not set
    # CONFIG_MK7 is not set
    # CONFIG_MK8 is not set
    # CONFIG_MCRUSOE is not set
    # CONFIG_MEFFICEON is not set
    # CONFIG_MWINCHIPC6 is not set
    # CONFIG_MWINCHIP3D is not set
    # CONFIG_MELAN is not set
    # CONFIG_MGEODEGX1 is not set
    # CONFIG_MGEODE_LX is not set
    # CONFIG_MCYRIXIII is not set
    # CONFIG_MVIAC3_2 is not set
    # CONFIG_MVIAC7 is not set
    # CONFIG_MCORE2 is not set
    # CONFIG_MATOM is not set
    CONFIG_X86_GENERIC=y
    CONFIG_X86_INTERNODE_CACHE_SHIFT=6
    CONFIG_X86_L1_CACHE_SHIFT=6
    # CONFIG_X86_PPRO_FENCE is not set
    CONFIG_X86_INTEL_USERCOPY=y
    CONFIG_X86_USE_PPRO_CHECKSUM=y
    CONFIG_X86_TSC=y
    CONFIG_X86_CMPXCHG64=y
    CONFIG_X86_CMOV=y
    CONFIG_X86_MINIMUM_CPU_FAMILY=5
    CONFIG_X86_DEBUGCTLMSR=y
    CONFIG_CPU_SUP_INTEL=y
    CONFIG_CPU_SUP_AMD=y
    CONFIG_CPU_SUP_CENTAUR=y
    CONFIG_CPU_SUP_TRANSMETA_32=y
    CONFIG_HPET_TIMER=y
    CONFIG_HPET_EMULATE_RTC=y
    CONFIG_DMI=y
    CONFIG_NR_CPUS=8
    CONFIG_SCHED_SMT=y
    CONFIG_SCHED_MC=y
    # CONFIG_PREEMPT_NONE is not set
    # CONFIG_PREEMPT_VOLUNTARY is not set
    CONFIG_PREEMPT=y
    CONFIG_PREEMPT_COUNT=y
    CONFIG_X86_LOCAL_APIC=y
    CONFIG_X86_IO_APIC=y
    CONFIG_X86_REROUTE_FOR_BROKEN_BOOT_IRQS=y
    CONFIG_X86_MCE=y
    CONFIG_X86_MCE_INTEL=y
    CONFIG_X86_MCE_AMD=y
    # CONFIG_X86_ANCIENT_MCE is not set
    CONFIG_X86_MCE_THRESHOLD=y
    # CONFIG_X86_MCE_INJECT is not set
    CONFIG_X86_THERMAL_VECTOR=y
    CONFIG_VM86=y
    CONFIG_TOSHIBA=m
    CONFIG_I8K=m
    CONFIG_X86_REBOOTFIXUPS=y
    CONFIG_MICROCODE=m
    CONFIG_MICROCODE_INTEL=y
    CONFIG_MICROCODE_AMD=y
    CONFIG_MICROCODE_OLD_INTERFACE=y
    CONFIG_MICROCODE_INTEL_LIB=y
    CONFIG_MICROCODE_INTEL_EARLY=y
    CONFIG_MICROCODE_EARLY=y
    CONFIG_X86_MSR=m
    CONFIG_X86_CPUID=m
    # CONFIG_NOHIGHMEM is not set
    CONFIG_HIGHMEM4G=y
    # CONFIG_HIGHMEM64G is not set
    CONFIG_PAGE_OFFSET=0xC0000000
    CONFIG_HIGHMEM=y
    CONFIG_ARCH_FLATMEM_ENABLE=y
    CONFIG_ARCH_SPARSEMEM_ENABLE=y
    CONFIG_ARCH_SELECT_MEMORY_MODEL=y
    CONFIG_ILLEGAL_POINTER_VALUE=0
    CONFIG_SELECT_MEMORY_MODEL=y
    CONFIG_FLATMEM_MANUAL=y
    # CONFIG_SPARSEMEM_MANUAL is not set
    CONFIG_FLATMEM=y
    CONFIG_FLAT_NODE_MEM_MAP=y
    CONFIG_SPARSEMEM_STATIC=y
    CONFIG_HAVE_MEMBLOCK=y
    CONFIG_HAVE_MEMBLOCK_NODE_MAP=y
    CONFIG_ARCH_DISCARD_MEMBLOCK=y
    CONFIG_MEMORY_ISOLATION=y
    # CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
    CONFIG_PAGEFLAGS_EXTENDED=y
    CONFIG_SPLIT_PTLOCK_CPUS=4
    CONFIG_BALLOON_COMPACTION=y
    CONFIG_COMPACTION=y
    CONFIG_MIGRATION=y
    # CONFIG_PHYS_ADDR_T_64BIT is not set
    CONFIG_ZONE_DMA_FLAG=1
    CONFIG_BOUNCE=y
    CONFIG_VIRT_TO_BUS=y
    CONFIG_MMU_NOTIFIER=y
    CONFIG_KSM=y
    CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
    CONFIG_ARCH_SUPPORTS_MEMORY_FAILURE=y
    CONFIG_MEMORY_FAILURE=y
    CONFIG_HWPOISON_INJECT=m
    CONFIG_TRANSPARENT_HUGEPAGE=y
    CONFIG_TRANSPARENT_HUGEPAGE_ALWAYS=y
    # CONFIG_TRANSPARENT_HUGEPAGE_MADVISE is not set
    CONFIG_CROSS_MEMORY_ATTACH=y
    CONFIG_CLEANCACHE=y
    CONFIG_FRONTSWAP=y
    # CONFIG_HIGHPTE is not set
    CONFIG_X86_CHECK_BIOS_CORRUPTION=y
    CONFIG_X86_BOOTPARAM_MEMORY_CORRUPTION_CHECK=y
    CONFIG_X86_RESERVE_LOW=64
    # CONFIG_MATH_EMULATION is not set
    CONFIG_MTRR=y
    CONFIG_MTRR_SANITIZER=y
    CONFIG_MTRR_SANITIZER_ENABLE_DEFAULT=0
    CONFIG_MTRR_SANITIZER_SPARE_REG_NR_DEFAULT=1
    CONFIG_X86_PAT=y
    CONFIG_ARCH_USES_PG_UNCACHED=y
    CONFIG_ARCH_RANDOM=y
    CONFIG_X86_SMAP=y
    CONFIG_EFI=y
    CONFIG_EFI_STUB=y
    CONFIG_SECCOMP=y
    CONFIG_CC_STACKPROTECTOR=y
    # CONFIG_HZ_100 is not set
    # CONFIG_HZ_250 is not set
    CONFIG_HZ_300=y
    # CONFIG_HZ_1000 is not set
    CONFIG_HZ=300
    CONFIG_SCHED_HRTICK=y
    CONFIG_KEXEC=y
    # CONFIG_CRASH_DUMP is not set
    # CONFIG_KEXEC_JUMP is not set
    CONFIG_PHYSICAL_START=0x1000000
    CONFIG_RELOCATABLE=y
    CONFIG_X86_NEED_RELOCS=y
    CONFIG_PHYSICAL_ALIGN=0x100000
    CONFIG_HOTPLUG_CPU=y
    # CONFIG_BOOTPARAM_HOTPLUG_CPU0 is not set
    # CONFIG_DEBUG_HOTPLUG_CPU0 is not set
    # CONFIG_COMPAT_VDSO is not set
    # CONFIG_CMDLINE_BOOL is not set
    CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
    # Power management and ACPI options
    CONFIG_SUSPEND=y
    CONFIG_SUSPEND_FREEZER=y
    CONFIG_HIBERNATE_CALLBACKS=y
    CONFIG_HIBERNATION=y
    CONFIG_PM_STD_PARTITION=""
    CONFIG_PM_SLEEP=y
    CONFIG_PM_SLEEP_SMP=y
    CONFIG_PM_AUTOSLEEP=y
    CONFIG_PM_WAKELOCKS=y
    CONFIG_PM_WAKELOCKS_LIMIT=100
    CONFIG_PM_WAKELOCKS_GC=y
    CONFIG_PM_RUNTIME=y
    CONFIG_PM=y
    CONFIG_PM_DEBUG=y
    CONFIG_PM_ADVANCED_DEBUG=y
    # CONFIG_PM_TEST_SUSPEND is not set
    CONFIG_PM_SLEEP_DEBUG=y
    CONFIG_PM_TRACE=y
    CONFIG_PM_TRACE_RTC=y
    CONFIG_ACPI=y
    CONFIG_ACPI_SLEEP=y
    # CONFIG_ACPI_PROCFS is not set
    # CONFIG_ACPI_PROCFS_POWER is not set
    CONFIG_ACPI_EC_DEBUGFS=m
    # CONFIG_ACPI_PROC_EVENT is not set
    CONFIG_ACPI_AC=m
    CONFIG_ACPI_BATTERY=m
    CONFIG_ACPI_BUTTON=m
    CONFIG_ACPI_VIDEO=m
    CONFIG_ACPI_FAN=m
    CONFIG_ACPI_DOCK=y
    CONFIG_ACPI_I2C=m
    CONFIG_ACPI_PROCESSOR=m
    CONFIG_ACPI_IPMI=m
    CONFIG_ACPI_HOTPLUG_CPU=y
    CONFIG_ACPI_PROCESSOR_AGGREGATOR=m
    CONFIG_ACPI_THERMAL=m
    # CONFIG_ACPI_CUSTOM_DSDT is not set
    CONFIG_ACPI_INITRD_TABLE_OVERRIDE=y
    CONFIG_ACPI_BLACKLIST_YEAR=0
    # CONFIG_ACPI_DEBUG is not set
    CONFIG_ACPI_PCI_SLOT=y
    CONFIG_X86_PM_TIMER=y
    CONFIG_ACPI_CONTAINER=y
    CONFIG_ACPI_SBS=m
    CONFIG_ACPI_HED=y
    CONFIG_ACPI_CUSTOM_METHOD=m
    CONFIG_ACPI_BGRT=y
    CONFIG_ACPI_APEI=y
    CONFIG_ACPI_APEI_GHES=y
    CONFIG_ACPI_APEI_PCIEAER=y
    CONFIG_ACPI_APEI_MEMORY_FAILURE=y
    CONFIG_ACPI_APEI_EINJ=m
    CONFIG_ACPI_APEI_ERST_DEBUG=m
    CONFIG_SFI=y
    CONFIG_X86_APM_BOOT=y
    CONFIG_APM=y
    # CONFIG_APM_IGNORE_USER_SUSPEND is not set
    CONFIG_APM_DO_ENABLE=y
    # CONFIG_APM_CPU_IDLE is not set
    # CONFIG_APM_DISPLAY_BLANK is not set
    # CONFIG_APM_ALLOW_INTS is not set
    # CPU Frequency scaling
    CONFIG_CPU_FREQ=y
    CONFIG_CPU_FREQ_TABLE=y
    CONFIG_CPU_FREQ_GOV_COMMON=y
    CONFIG_CPU_FREQ_STAT=m
    CONFIG_CPU_FREQ_STAT_DETAILS=y
    # CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
    # CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
    CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y
    # CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
    CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
    CONFIG_CPU_FREQ_GOV_POWERSAVE=m
    CONFIG_CPU_FREQ_GOV_USERSPACE=m
    CONFIG_CPU_FREQ_GOV_ONDEMAND=y
    CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
    # x86 CPU frequency scaling drivers
    CONFIG_X86_INTEL_PSTATE=y
    CONFIG_X86_PCC_CPUFREQ=m
    CONFIG_X86_ACPI_CPUFREQ=m
    CONFIG_X86_ACPI_CPUFREQ_CPB=y
    CONFIG_X86_POWERNOW_K6=m
    CONFIG_X86_POWERNOW_K7=m
    CONFIG_X86_POWERNOW_K7_ACPI=y
    CONFIG_X86_POWERNOW_K8=m
    CONFIG_X86_GX_SUSPMOD=m
    # CONFIG_X86_SPEEDSTEP_CENTRINO is not set
    CONFIG_X86_SPEEDSTEP_ICH=m
    CONFIG_X86_SPEEDSTEP_SMI=m
    CONFIG_X86_P4_CLOCKMOD=m
    CONFIG_X86_CPUFREQ_NFORCE2=m
    CONFIG_X86_LONGRUN=m
    CONFIG_X86_LONGHAUL=m
    CONFIG_X86_E_POWERSAVER=m
    # shared options
    CONFIG_X86_SPEEDSTEP_LIB=m
    CONFIG_X86_SPEEDSTEP_RELAXED_CAP_CHECK=y
    CONFIG_CPU_IDLE=y
    # CONFIG_CPU_IDLE_MULTIPLE_DRIVERS is not set
    CONFIG_CPU_IDLE_GOV_LADDER=y
    CONFIG_CPU_IDLE_GOV_MENU=y
    # CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED is not set
    CONFIG_INTEL_IDLE=y
    # Bus options (PCI etc.)
    CONFIG_PCI=y
    # CONFIG_PCI_GOBIOS is not set
    # CONFIG_PCI_GOMMCONFIG is not set
    # CONFIG_PCI_GODIRECT is not set
    # CONFIG_PCI_GOOLPC is not set
    CONFIG_PCI_GOANY=y
    CONFIG_PCI_BIOS=y
    CONFIG_PCI_DIRECT=y
    CONFIG_PCI_MMCONFIG=y
    CONFIG_PCI_OLPC=y
    CONFIG_PCI_DOMAINS=y
    CONFIG_PCIEPORTBUS=y
    CONFIG_HOTPLUG_PCI_PCIE=m
    CONFIG_PCIEAER=y
    # CONFIG_PCIE_ECRC is not set
    # CONFIG_PCIEAER_INJECT is not set
    CONFIG_PCIEASPM=y
    # CONFIG_PCIEASPM_DEBUG is not set
    CONFIG_PCIEASPM_DEFAULT=y
    # CONFIG_PCIEASPM_POWERSAVE is not set
    # CONFIG_PCIEASPM_PERFORMANCE is not set
    CONFIG_PCIE_PME=y
    CONFIG_ARCH_SUPPORTS_MSI=y
    CONFIG_PCI_MSI=y
    # CONFIG_PCI_DEBUG is not set
    CONFIG_PCI_REALLOC_ENABLE_AUTO=y
    CONFIG_PCI_STUB=m
    CONFIG_HT_IRQ=y
    CONFIG_PCI_ATS=y
    CONFIG_PCI_IOV=y
    CONFIG_PCI_PRI=y
    CONFIG_PCI_PASID=y
    CONFIG_PCI_IOAPIC=y
    CONFIG_PCI_LABEL=y
    CONFIG_ISA_DMA_API=y
    CONFIG_ISA=y
    # CONFIG_EISA is not set
    # CONFIG_SCx200 is not set
    CONFIG_OLPC=y
    CONFIG_OLPC_XO1_PM=y
    CONFIG_OLPC_XO1_RTC=y
    CONFIG_OLPC_XO1_SCI=y
    CONFIG_OLPC_XO15_SCI=y
    # CONFIG_ALIX is not set
    # CONFIG_NET5501 is not set
    # CONFIG_GEOS is not set
    CONFIG_AMD_NB=y
    CONFIG_PCCARD=m
    CONFIG_PCMCIA=m
    CONFIG_PCMCIA_LOAD_CIS=y
    CONFIG_CARDBUS=y
    # PC-card bridges
    CONFIG_YENTA=m
    CONFIG_YENTA_O2=y
    CONFIG_YENTA_RICOH=y
    CONFIG_YENTA_TI=y
    CONFIG_YENTA_ENE_TUNE=y
    CONFIG_YENTA_TOSHIBA=y
    CONFIG_PD6729=m
    CONFIG_I82092=m
    CONFIG_I82365=m
    CONFIG_TCIC=m
    CONFIG_PCMCIA_PROBE=y
    CONFIG_PCCARD_NONSTATIC=y
    CONFIG_HOTPLUG_PCI=m
    CONFIG_HOTPLUG_PCI_COMPAQ=m
    # CONFIG_HOTPLUG_PCI_COMPAQ_NVRAM is not set
    CONFIG_HOTPLUG_PCI_IBM=m
    CONFIG_HOTPLUG_PCI_ACPI=m
    CONFIG_HOTPLUG_PCI_ACPI_IBM=m
    CONFIG_HOTPLUG_PCI_CPCI=y
    CONFIG_HOTPLUG_PCI_CPCI_ZT5550=m
    CONFIG_HOTPLUG_PCI_CPCI_GENERIC=m
    CONFIG_HOTPLUG_PCI_SHPC=m
    CONFIG_RAPIDIO=y
    CONFIG_RAPIDIO_TSI721=y
    CONFIG_RAPIDIO_DISC_TIMEOUT=30
    # CONFIG_RAPIDIO_ENABLE_RX_TX_PORTS is not set
    CONFIG_RAPIDIO_DMA_ENGINE=y
    CONFIG_RAPIDIO_DEBUG=y
    CONFIG_RAPIDIO_TSI57X=y
    CONFIG_RAPIDIO_CPS_XX=y
    CONFIG_RAPIDIO_TSI568=y
    CONFIG_RAPIDIO_CPS_GEN2=y
    CONFIG_RAPIDIO_TSI500=y
    # Executable file formats / Emulations
    CONFIG_BINFMT_ELF=y
    CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
    # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
    CONFIG_HAVE_AOUT=y
    CONFIG_BINFMT_AOUT=m
    CONFIG_BINFMT_MISC=y
    CONFIG_COREDUMP=y
    CONFIG_HAVE_ATOMIC_IOMAP=y
    CONFIG_HAVE_TEXT_POKE_SMP=y
    CONFIG_NET=y
    # Networking options
    CONFIG_PACKET=y
    CONFIG_PACKET_DIAG=m
    CONFIG_UNIX=y
    CONFIG_UNIX_DIAG=m
    CONFIG_XFRM=y
    CONFIG_XFRM_ALGO=m
    CONFIG_XFRM_USER=m
    # CONFIG_XFRM_SUB_POLICY is not set
    # CONFIG_XFRM_MIGRATE is not set
    # CONFIG_XFRM_STATISTICS is not set
    CONFIG_XFRM_IPCOMP=m
    CONFIG_NET_KEY=m
    # CONFIG_NET_KEY_MIGRATE is not set
    CONFIG_INET=y
    CONFIG_IP_MULTICAST=y
    CONFIG_IP_ADVANCED_ROUTER=y
    CONFIG_IP_FIB_TRIE_STATS=y
    CONFIG_IP_MULTIPLE_TABLES=y
    CONFIG_IP_ROUTE_MULTIPATH=y
    CONFIG_IP_ROUTE_VERBOSE=y
    CONFIG_IP_ROUTE_CLASSID=y
    # CONFIG_IP_PNP is not set
    CONFIG_NET_IPIP=m
    CONFIG_NET_IPGRE_DEMUX=m
    CONFIG_NET_IPGRE=m
    # CONFIG_NET_IPGRE_BROADCAST is not set
    CONFIG_IP_MROUTE=y
    # CONFIG_IP_MROUTE_MULTIPLE_TABLES is not set
    CONFIG_IP_PIMSM_V1=y
    CONFIG_IP_PIMSM_V2=y
    CONFIG_ARPD=y
    CONFIG_SYN_COOKIES=y
    CONFIG_NET_IPVTI=m
    CONFIG_INET_AH=m
    CONFIG_INET_ESP=m
    CONFIG_INET_IPCOMP=m
    CONFIG_INET_XFRM_TUNNEL=m
    CONFIG_INET_TUNNEL=m
    CONFIG_INET_XFRM_MODE_TRANSPORT=m
    CONFIG_INET_XFRM_MODE_TUNNEL=m
    CONFIG_INET_XFRM_MODE_BEET=m
    CONFIG_INET_LRO=y
    CONFIG_INET_DIAG=y
    CONFIG_INET_TCP_DIAG=y
    CONFIG_INET_UDP_DIAG=m
    CONFIG_TCP_CONG_ADVANCED=y
    CONFIG_TCP_CONG_BIC=m
    CONFIG_TCP_CONG_CUBIC=y
    CONFIG_TCP_CONG_WESTWOOD=m
    CONFIG_TCP_CONG_HTCP=m
    CONFIG_TCP_CONG_HSTCP=m
    CONFIG_TCP_CONG_HYBLA=m
    CONFIG_TCP_CONG_VEGAS=m
    CONFIG_TCP_CONG_SCALABLE=m
    CONFIG_TCP_CONG_LP=m
    CONFIG_TCP_CONG_VENO=m
    CONFIG_TCP_CONG_YEAH=m
    CONFIG_TCP_CONG_ILLINOIS=m
    CONFIG_DEFAULT_CUBIC=y
    # CONFIG_DEFAULT_RENO is not set
    CONFIG_DEFAULT_TCP_CONG="cubic"
    # CONFIG_TCP_MD5SIG is not set
    CONFIG_IPV6=y
    CONFIG_IPV6_PRIVACY=y
    CONFIG_IPV6_ROUTER_PREF=y
    CONFIG_IPV6_ROUTE_INFO=y
    CONFIG_IPV6_OPTIMISTIC_DAD=y
    CONFIG_INET6_AH=m
    CONFIG_INET6_ESP=m
    CONFIG_INET6_IPCOMP=m
    CONFIG_IPV6_MIP6=m
    CONFIG_INET6_XFRM_TUNNEL=m
    CONFIG_INET6_TUNNEL=m
    CONFIG_INET6_XFRM_MODE_TRANSPORT=m
    CONFIG_INET6_XFRM_MODE_TUNNEL=m
    CONFIG_INET6_XFRM_MODE_BEET=m
    CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
    CONFIG_IPV6_SIT=m
    CONFIG_IPV6_SIT_6RD=y
    CONFIG_IPV6_NDISC_NODETYPE=y
    CONFIG_IPV6_TUNNEL=m
    CONFIG_IPV6_GRE=m
    CONFIG_IPV6_MULTIPLE_TABLES=y
    CONFIG_IPV6_SUBTREES=y
    # CONFIG_IPV6_MROUTE is not set
    CONFIG_NETLABEL=y
    CONFIG_NETWORK_SECMARK=y
    CONFIG_NETWORK_PHY_TIMESTAMPING=y
    CONFIG_NETFILTER=y
    # CONFIG_NETFILTER_DEBUG is not set
    CONFIG_NETFILTER_ADVANCED=y
    CONFIG_BRIDGE_NETFILTER=y
    # Core Netfilter Configuration
    CONFIG_NETFILTER_NETLINK=m
    CONFIG_NETFILTER_NETLINK_ACCT=m
    CONFIG_NETFILTER_NETLINK_QUEUE=m
    CONFIG_NETFILTER_NETLINK_LOG=m
    CONFIG_NF_CONNTRACK=m
    CONFIG_NF_CONNTRACK_MARK=y
    CONFIG_NF_CONNTRACK_SECMARK=y
    CONFIG_NF_CONNTRACK_ZONES=y
    CONFIG_NF_CONNTRACK_PROCFS=y
    CONFIG_NF_CONNTRACK_EVENTS=y
    CONFIG_NF_CONNTRACK_TIMEOUT=y
    CONFIG_NF_CONNTRACK_TIMESTAMP=y
    CONFIG_NF_CONNTRACK_LABELS=y
    CONFIG_NF_CT_PROTO_DCCP=m
    CONFIG_NF_CT_PROTO_GRE=m
    CONFIG_NF_CT_PROTO_SCTP=m
    CONFIG_NF_CT_PROTO_UDPLITE=m
    CONFIG_NF_CONNTRACK_AMANDA=m
    CONFIG_NF_CONNTRACK_FTP=m
    CONFIG_NF_CONNTRACK_H323=m
    CONFIG_NF_CONNTRACK_IRC=m
    CONFIG_NF_CONNTRACK_BROADCAST=m
    CONFIG_NF_CONNTRACK_NETBIOS_NS=m
    CONFIG_NF_CONNTRACK_SNMP=m
    CONFIG_NF_CONNTRACK_PPTP=m
    CONFIG_NF_CONNTRACK_SANE=m
    CONFIG_NF_CONNTRACK_SIP=m
    CONFIG_NF_CONNTRACK_TFTP=m
    CONFIG_NF_CT_NETLINK=m
    CONFIG_NF_CT_NETLINK_TIMEOUT=m
    CONFIG_NF_CT_NETLINK_HELPER=m
    CONFIG_NETFILTER_NETLINK_QUEUE_CT=y
    CONFIG_NF_NAT=m
    CONFIG_NF_NAT_NEEDED=y
    CONFIG_NF_NAT_PROTO_DCCP=m
    CONFIG_NF_NAT_PROTO_UDPLITE=m
    CONFIG_NF_NAT_PROTO_SCTP=m
    CONFIG_NF_NAT_AMANDA=m
    CONFIG_NF_NAT_FTP=m
    CONFIG_NF_NAT_IRC=m
    CONFIG_NF_NAT_SIP=m
    CONFIG_NF_NAT_TFTP=m
    CONFIG_NETFILTER_TPROXY=m
    CONFIG_NETFILTER_XTABLES=m
    # Xtables combined modules
    CONFIG_NETFILTER_XT_MARK=m
    CONFIG_NETFILTER_XT_CONNMARK=m
    CONFIG_NETFILTER_XT_SET=m
    # Xtables targets
    CONFIG_NETFILTER_XT_TARGET_AUDIT=m
    CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
    CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
    CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
    CONFIG_NETFILTER_XT_TARGET_CONNSECMARK=m
    CONFIG_NETFILTER_XT_TARGET_CT=m
    CONFIG_NETFILTER_XT_TARGET_DSCP=m
    CONFIG_NETFILTER_XT_TARGET_HL=m
    CONFIG_NETFILTER_XT_TARGET_HMARK=m
    CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
    CONFIG_NETFILTER_XT_TARGET_LED=m
    CONFIG_NETFILTER_XT_TARGET_LOG=m
    CONFIG_NETFILTER_XT_TARGET_MARK=m
    CONFIG_NETFILTER_XT_TARGET_NETMAP=m
    CONFIG_NETFILTER_XT_TARGET_NFLOG=m
    CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
    CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
    CONFIG_NETFILTER_XT_TARGET_RATEEST=m
    CONFIG_NETFILTER_XT_TARGET_REDIRECT=m
    CONFIG_NETFILTER_XT_TARGET_TEE=m
    CONFIG_NETFILTER_XT_TARGET_TPROXY=m
    CONFIG_NETFILTER_XT_TARGET_TRACE=m
    CONFIG_NETFILTER_XT_TARGET_SECMARK=m
    CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
    CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
    # Xtables matches
    CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
    CONFIG_NETFILTER_XT_MATCH_BPF=m
    CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
    CONFIG_NETFILTER_XT_MATCH_COMMENT=m
    CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
    CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
    CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
    CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
    CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
    CONFIG_NETFILTER_XT_MATCH_CPU=m
    CONFIG_NETFILTER_XT_MATCH_DCCP=m
    CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
    CONFIG_NETFILTER_XT_MATCH_DSCP=m
    CONFIG_NETFILTER_XT_MATCH_ECN=m
    CONFIG_NETFILTER_XT_MATCH_ESP=m
    CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
    CONFIG_NETFILTER_XT_MATCH_HELPER=m
    CONFIG_NETFILTER_XT_MATCH_HL=m
    CONFIG_NETFILTER_XT_MATCH_IPRANGE=m
    CONFIG_NETFILTER_XT_MATCH_IPVS=m
    CONFIG_NETFILTER_XT_MATCH_LENGTH=m
    CONFIG_NETFILTER_XT_MATCH_LIMIT=m
    CONFIG_NETFILTER_XT_MATCH_MAC=m
    CONFIG_NETFILTER_XT_MATCH_MARK=m
    CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
    CONFIG_NETFILTER_XT_MATCH_NFACCT=m
    CONFIG_NETFILTER_XT_MATCH_OSF=m
    CONFIG_NETFILTER_XT_MATCH_OWNER=m
    CONFIG_NETFILTER_XT_MATCH_POLICY=m
    CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
    CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
    CONFIG_NETFILTER_XT_MATCH_QUOTA=m
    CONFIG_NETFILTER_XT_MATCH_RATEEST=m
    CONFIG_NETFILTER_XT_MATCH_REALM=m
    CONFIG_NETFILTER_XT_MATCH_RECENT=m
    CONFIG_NETFILTER_XT_MATCH_SCTP=m
    CONFIG_NETFILTER_XT_MATCH_SOCKET=m
    CONFIG_NETFILTER_XT_MATCH_STATE=m
    CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
    CONFIG_NETFILTER_XT_MATCH_STRING=m
    CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
    CONFIG_NETFILTER_XT_MATCH_TIME=m
    CONFIG_NETFILTER_XT_MATCH_U32=m
    CONFIG_IP_SET=m
    CONFIG_IP_SET_MAX=256
    CONFIG_IP_SET_BITMAP_IP=m
    CONFIG_IP_SET_BITMAP_IPMAC=m
    CONFIG_IP_SET_BITMAP_PORT=m
    CONFIG_IP_SET_HASH_IP=m
    CONFIG_IP_SET_HASH_IPPORT=m
    CONFIG_IP_SET_HASH_IPPORTIP=m
    CONFIG_IP_SET_HASH_IPPORTNET=m
    CONFIG_IP_SET_HASH_NET=m
    CONFIG_IP_SET_HASH_NETPORT=m
    CONFIG_IP_SET_HASH_NETIFACE=m
    CONFIG_IP_SET_LIST_SET=m
    CONFIG_IP_VS=m
    # CONFIG_IP_VS_IPV6 is not set
    # CONFIG_IP_VS_DEBUG is not set
    CONFIG_IP_VS_TAB_BITS=12
    # IPVS transport protocol load balancing support
    CONFIG_IP_VS_PROTO_TCP=y
    CONFIG_IP_VS_PROTO_UDP=y
    CONFIG_IP_VS_PROTO_AH_ESP=y
    CONFIG_IP_VS_PROTO_ESP=y
    CONFIG_IP_VS_PROTO_AH=y
    CONFIG_IP_VS_PROTO_SCTP=y
    # IPVS scheduler
    CONFIG_IP_VS_RR=m
    CONFIG_IP_VS_WRR=m
    CONFIG_IP_VS_LC=m
    CONFIG_IP_VS_WLC=m
    CONFIG_IP_VS_LBLC=m
    CONFIG_IP_VS_LBLCR=m
    CONFIG_IP_VS_DH=m
    CONFIG_IP_VS_SH=m
    CONFIG_IP_VS_SED=m
    CONFIG_IP_VS_NQ=m
    # IPVS SH scheduler
    CONFIG_IP_VS_SH_TAB_BITS=8
    # IPVS application helper
    CONFIG_IP_VS_FTP=m
    CONFIG_IP_VS_NFCT=y
    CONFIG_IP_VS_PE_SIP=m
    # IP: Netfilter Configuration
    CONFIG_NF_DEFRAG_IPV4=m
    CONFIG_NF_CONNTRACK_IPV4=m
    # CONFIG_NF_CONNTRACK_PROC_COMPAT is not set
    CONFIG_IP_NF_IPTABLES=m
    CONFIG_IP_NF_MATCH_AH=m
    CONFIG_IP_NF_MATCH_ECN=m
    CONFIG_IP_NF_MATCH_RPFILTER=m
    CONFIG_IP_NF_MATCH_TTL=m
    CONFIG_IP_NF_FILTER=m
    CONFIG_IP_NF_TARGET_REJECT=m
    CONFIG_IP_NF_TARGET_ULOG=m
    CONFIG_NF_NAT_IPV4=m
    CONFIG_IP_NF_TARGET_MASQUERADE=m
    CONFIG_IP_NF_TARGET_NETMAP=m
    CONFIG_IP_NF_TARGET_REDIRECT=m
    CONFIG_NF_NAT_SNMP_BASIC=m
    CONFIG_NF_NAT_PROTO_GRE=m
    CONFIG_NF_NAT_PPTP=m
    CONFIG_NF_NAT_H323=m
    CONFIG_IP_NF_MANGLE=m
    CONFIG_IP_NF_TARGET_CLUSTERIP=m
    CONFIG_IP_NF_TARGET_ECN=m
    CONFIG_IP_NF_TARGET_TTL=m
    CONFIG_IP_NF_RAW=m
    CONFIG_IP_NF_SECURITY=m
    CONFIG_IP_NF_ARPTABLES=m
    CONFIG_IP_NF_ARPFILTER=m
    CONFIG_IP_NF_ARP_MANGLE=m
    # IPv6: Netfilter Configuration
    CONFIG_NF_DEFRAG_IPV6=m
    CONFIG_NF_CONNTRACK_IPV6=m
    CONFIG_IP6_NF_IPTABLES=m
    CONFIG_IP6_NF_MATCH_AH=m
    CONFIG_IP6_NF_MATCH_EUI64=m
    CONFIG_IP6_NF_MATCH_FRAG=m
    CONFIG_IP6_NF_MATCH_OPTS=m
    CONFIG_IP6_NF_MATCH_HL=m
    CONFIG_IP6_NF_MATCH_IPV6HEADER=m
    CONFIG_IP6_NF_MATCH_MH=m
    CONFIG_IP6_NF_MATCH_RPFILTER=m
    CONFIG_IP6_NF_MATCH_RT=m
    CONFIG_IP6_NF_TARGET_HL=m
    CONFIG_IP6_NF_FILTER=m
    CONFIG_IP6_NF_TARGET_REJECT=m
    CONFIG_IP6_NF_MANGLE=m
    CONFIG_IP6_NF_RAW=m
    CONFIG_IP6_NF_SECURITY=m
    CONFIG_NF_NAT_IPV6=m
    CONFIG_IP6_NF_TARGET_MASQUERADE=m
    CONFIG_IP6_NF_TARGET_NPT=m
    CONFIG_BRIDGE_NF_EBTABLES=m
    CONFIG_BRIDGE_EBT_BROUTE=m
    CONFIG_BRIDGE_EBT_T_FILTER=m
    CONFIG_BRIDGE_EBT_T_NAT=m
    CONFIG_BRIDGE_EBT_802_3=m
    CONFIG_BRIDGE_EBT_AMONG=m
    CONFIG_BRIDGE_EBT_ARP=m
    CONFIG_BRIDGE_EBT_IP=m
    CONFIG_BRIDGE_EBT_IP6=m
    CONFIG_BRIDGE_EBT_LIMIT=m
    CONFIG_BRIDGE_EBT_MARK=m
    CONFIG_BRIDGE_EBT_PKTTYPE=m
    CONFIG_BRIDGE_EBT_STP=m
    CONFIG_BRIDGE_EBT_VLAN=m
    CONFIG_BRIDGE_EBT_ARPREPLY=m
    CONFIG_BRIDGE_EBT_DNAT=m
    CONFIG_BRIDGE_EBT_MARK_T=m
    CONFIG_BRIDGE_EBT_REDIRECT=m
    CONFIG_BRIDGE_EBT_SNAT=m
    CONFIG_BRIDGE_EBT_LOG=m
    CONFIG_BRIDGE_EBT_ULOG=m
    CONFIG_BRIDGE_EBT_NFLOG=m
    CONFIG_IP_DCCP=m
    CONFIG_INET_DCCP_DIAG=m
    # DCCP CCIDs Configuration
    # CONFIG_IP_DCCP_CCID2_DEBUG is not set
    CONFIG_IP_DCCP_CCID3=y
    # CONFIG_IP_DCCP_CCID3_DEBUG is not set
    CONFIG_IP_DCCP_TFRC_LIB=y
    # DCCP Kernel Hacking
    # CONFIG_IP_DCCP_DEBUG is not set
    CONFIG_NET_DCCPPROBE=m
    CONFIG_IP_SCTP=m
    CONFIG_NET_SCTPPROBE=m
    # CONFIG_SCTP_DBG_MSG is not set
    # CONFIG_SCTP_DBG_OBJCNT is not set
    # CONFIG_SCTP_DEFAULT_COOKIE_HMAC_MD5 is not set
    CONFIG_SCTP_DEFAULT_COOKIE_HMAC_SHA1=y
    # CONFIG_SCTP_DEFAULT_COOKIE_HMAC_NONE is not set
    CONFIG_SCTP_COOKIE_HMAC_MD5=y
    CONFIG_SCTP_COOKIE_HMAC_SHA1=y
    # CONFIG_RDS is not set
    # CONFIG_TIPC is not set
    CONFIG_ATM=m
    CONFIG_ATM_CLIP=m
    # CONFIG_ATM_CLIP_NO_ICMP is not set
    CONFIG_ATM_LANE=m
    CONFIG_ATM_MPOA=m
    CONFIG_ATM_BR2684=m
    # CONFIG_ATM_BR2684_IPFILTER is not set
    CONFIG_L2TP=m
    # CONFIG_L2TP_DEBUGFS is not set
    CONFIG_L2TP_V3=y
    CONFIG_L2TP_IP=m
    CONFIG_L2TP_ETH=m
    CONFIG_STP=m
    CONFIG_MRP=m
    CONFIG_BRIDGE=m
    CONFIG_BRIDGE_IGMP_SNOOPING=y
    CONFIG_BRIDGE_VLAN_FILTERING=y
    CONFIG_HAVE_NET_DSA=y
    CONFIG_NET_DSA=m
    CONFIG_NET_DSA_TAG_DSA=y
    CONFIG_NET_DSA_TAG_EDSA=y
    CONFIG_NET_DSA_TAG_TRAILER=y
    CONFIG_VLAN_8021Q=m
    # CONFIG_VLAN_8021Q_GVRP is not set
    CONFIG_VLAN_8021Q_MVRP=y
    # CONFIG_DECNET is not set
    CONFIG_LLC=m
    CONFIG_LLC2=m
    CONFIG_IPX=m
    # CONFIG_IPX_INTERN is not set
    CONFIG_ATALK=m
    CONFIG_DEV_APPLETALK=m
    CONFIG_LTPC=m
    CONFIG_COPS=m
    CONFIG_COPS_DAYNA=y
    CONFIG_COPS_TANGENT=y
    CONFIG_IPDDP=m
    CONFIG_IPDDP_ENCAP=y
    CONFIG_IPDDP_DECAP=y
    # CONFIG_X25 is not set
    # CONFIG_LAPB is not set
    CONFIG_PHONET=m
    CONFIG_IEEE802154=m
    CONFIG_IEEE802154_6LOWPAN=m
    CONFIG_MAC802154=m
    CONFIG_NET_SCHED=y
    # Queueing/Scheduling
    CONFIG_NET_SCH_CBQ=m
    CONFIG_NET_SCH_HTB=m
    CONFIG_NET_SCH_HFSC=m
    CONFIG_NET_SCH_ATM=m
    CONFIG_NET_SCH_PRIO=m
    CONFIG_NET_SCH_MULTIQ=m
    CONFIG_NET_SCH_RED=m
    CONFIG_NET_SCH_SFB=m
    CONFIG_NET_SCH_SFQ=m
    CONFIG_NET_SCH_TEQL=m
    CONFIG_NET_SCH_TBF=m
    CONFIG_NET_SCH_GRED=m
    CONFIG_NET_SCH_DSMARK=m
    CONFIG_NET_SCH_NETEM=m
    CONFIG_NET_SCH_DRR=m
    CONFIG_NET_SCH_MQPRIO=m
    CONFIG_NET_SCH_CHOKE=m
    CONFIG_NET_SCH_QFQ=m
    CONFIG_NET_SCH_CODEL=m
    CONFIG_NET_SCH_FQ_CODEL=m
    CONFIG_NET_SCH_INGRESS=m
    CONFIG_NET_SCH_PLUG=m
    # Classification
    CONFIG_NET_CLS=y
    CONFIG_NET_CLS_BASIC=m
    CONFIG_NET_CLS_TCINDEX=m
    CONFIG_NET_CLS_ROUTE4=m
    CONFIG_NET_CLS_FW=m
    CONFIG_NET_CLS_U32=m
    # CONFIG_CLS_U32_PERF is not set
    # CONFIG_CLS_U32_MARK is not set
    CONFIG_NET_CLS_RSVP=m
    CONFIG_NET_CLS_RSVP6=m
    CONFIG_NET_CLS_FLOW=m
    CONFIG_NET_CLS_CGROUP=y
    # CONFIG_NET_EMATCH is not set
    CONFIG_NET_CLS_ACT=y
    CONFIG_NET_ACT_POLICE=m
    CONFIG_NET_ACT_GACT=m
    CONFIG_GACT_PROB=y
    CONFIG_NET_ACT_MIRRED=m
    CONFIG_NET_ACT_IPT=m
    CONFIG_NET_ACT_NAT=m
    CONFIG_NET_ACT_PEDIT=m
    CONFIG_NET_ACT_SIMP=m
    CONFIG_NET_ACT_SKBEDIT=m
    CONFIG_NET_ACT_CSUM=m
    CONFIG_NET_CLS_IND=y
    CONFIG_NET_SCH_FIFO=y
    # CONFIG_DCB is not set
    CONFIG_DNS_RESOLVER=y
    CONFIG_BATMAN_ADV=m
    CONFIG_BATMAN_ADV_BLA=y
    CONFIG_BATMAN_ADV_DAT=y
    # CONFIG_BATMAN_ADV_DEBUG is not set
    CONFIG_OPENVSWITCH=m
    CONFIG_VSOCKETS=m
    CONFIG_VMWARE_VMCI_VSOCKETS=m
    CONFIG_RPS=y
    CONFIG_RFS_ACCEL=y
    CONFIG_XPS=y
    CONFIG_NETPRIO_CGROUP=m
    CONFIG_BQL=y
    # Network testing
    CONFIG_NET_PKTGEN=m
    CONFIG_NET_TCPPROBE=m
    CONFIG_NET_DROP_MONITOR=y
    CONFIG_HAMRADIO=y
    # Packet Radio protocols
    CONFIG_AX25=m
    CONFIG_AX25_DAMA_SLAVE=y
    CONFIG_NETROM=m
    CONFIG_ROSE=m
    # AX.25 network device drivers
    CONFIG_MKISS=m
    CONFIG_6PACK=m
    CONFIG_BPQETHER=m
    CONFIG_SCC=m
    # CONFIG_SCC_DELAY is not set
    # CONFIG_SCC_TRXECHO is not set
    CONFIG_BAYCOM_SER_FDX=m
    CONFIG_BAYCOM_SER_HDX=m
    CONFIG_BAYCOM_PAR=m
    CONFIG_BAYCOM_EPP=m
    CONFIG_YAM=m
    # CONFIG_CAN is not set
    CONFIG_IRDA=m
    # IrDA protocols
    CONFIG_IRLAN=m
    CONFIG_IRNET=m
    CONFIG_IRCOMM=m
    CONFIG_IRDA_ULTRA=y
    # IrDA options
    CONFIG_IRDA_CACHE_LAST_LSAP=y
    CONFIG_IRDA_FAST_RR=y
    # CONFIG_IRDA_DEBUG is not set
    # Infrared-port device drivers
    # SIR device drivers
    CONFIG_IRTTY_SIR=m
    # Dongle support
    CONFIG_DONGLE=y
    CONFIG_ESI_DONGLE=m
    CONFIG_ACTISYS_DONGLE=m
    CONFIG_TEKRAM_DONGLE=m
    CONFIG_TOIM3232_DONGLE=m
    CONFIG_LITELINK_DONGLE=m
    CONFIG_MA600_DONGLE=m
    CONFIG_GIRBIL_DONGLE=m
    CONFIG_MCP2120_DONGLE=m
    CONFIG_OLD_BELKIN_DONGLE=m
    CONFIG_ACT200L_DONGLE=m
    CONFIG_KINGSUN_DONGLE=m
    CONFIG_KSDAZZLE_DONGLE=m
    CONFIG_KS959_DONGLE=m
    # FIR device drivers
    CONFIG_USB_IRDA=m
    CONFIG_SIGMATEL_FIR=m
    CONFIG_NSC_FIR=m
    CONFIG_WINBOND_FIR=m
    CONFIG_TOSHIBA_FIR=m
    CONFIG_SMC_IRCC_FIR=m
    CONFIG_ALI_FIR=m
    CONFIG_VLSI_FIR=m
    CONFIG_VIA_FIR=m
    CONFIG_MCS_FIR=m
    CONFIG_BT=m
    CONFIG_BT_RFCOMM=m
    CONFIG_BT_RFCOMM_TTY=y
    CONFIG_BT_BNEP=m
    # CONFIG_BT_BNEP_MC_FILTER is not set
    # CONFIG_BT_BNEP_PROTO_FILTER is not set
    # CONFIG_BT_CMTP is not set
    CONFIG_BT_HIDP=m
    # Bluetooth device drivers
    CONFIG_BT_HCIBTUSB=m
    CONFIG_BT_HCIBTSDIO=m
    CONFIG_BT_HCIUART=m
    CONFIG_BT_HCIUART_H4=y
    CONFIG_BT_HCIUART_BCSP=y
    CONFIG_BT_HCIUART_ATH3K=y
    CONFIG_BT_HCIUART_LL=y
    CONFIG_BT_HCIUART_3WIRE=y
    CONFIG_BT_HCIBCM203X=m
    CONFIG_BT_HCIBPA10X=m
    CONFIG_BT_HCIBFUSB=m
    CONFIG_BT_HCIDTL1=m
    CONFIG_BT_HCIBT3C=m
    CONFIG_BT_HCIBLUECARD=m
    CONFIG_BT_HCIBTUART=m
    CONFIG_BT_HCIVHCI=m
    CONFIG_BT_MRVL=m
    CONFIG_BT_MRVL_SDIO=m
    CONFIG_BT_ATH3K=m
    CONFIG_BT_WILINK=m
    CONFIG_AF_RXRPC=m
    # CONFIG_AF_RXRPC_DEBUG is not set
    CONFIG_RXKAD=m
    CONFIG_FIB_RULES=y
    CONFIG_WIRELESS=y
    CONFIG_WIRELESS_EXT=y
    CONFIG_WEXT_CORE=y
    CONFIG_WEXT_PROC=y
    CONFIG_WEXT_SPY=y
    CONFIG_WEXT_PRIV=y
    CONFIG_CFG80211=m
    # CONFIG_NL80211_TESTMODE is not set
    # CONFIG_CFG80211_DEVELOPER_WARNINGS is not set
    # CONFIG_CFG80211_REG_DEBUG is not set
    CONFIG_CFG80211_DEFAULT_PS=y
    # CONFIG_CFG80211_DEBUGFS is not set
    # CONFIG_CFG80211_INTERNAL_REGDB is not set
    CONFIG_CFG80211_WEXT=y
    CONFIG_LIB80211=m
    CONFIG_LIB80211_CRYPT_WEP=m
    CONFIG_LIB80211_CRYPT_CCMP=m
    CONFIG_LIB80211_CRYPT_TKIP=m
    # CONFIG_LIB80211_DEBUG is not set
    CONFIG_MAC80211=m
    CONFIG_MAC80211_HAS_RC=y
    CONFIG_MAC80211_RC_MINSTREL=y
    CONFIG_MAC80211_RC_MINSTREL_HT=y
    CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y
    CONFIG_MAC80211_RC_DEFAULT="minstrel_ht"
    CONFIG_MAC80211_MESH=y
    CONFIG_MAC80211_LEDS=y
    # CONFIG_MAC80211_DEBUGFS is not set
    # CONFIG_MAC80211_MESSAGE_TRACING is not set
    # CONFIG_MAC80211_DEBUG_MENU is not set
    CONFIG_WIMAX=m
    CONFIG_WIMAX_DEBUG_LEVEL=8
    CONFIG_RFKILL=m
    CONFIG_RFKILL_LEDS=y
    CONFIG_RFKILL_INPUT=y
    CONFIG_NET_9P=m
    CONFIG_NET_9P_VIRTIO=m
    # CONFIG_NET_9P_DEBUG is not set
    CONFIG_CAIF=m
    # CONFIG_CAIF_DEBUG is not set
    CONFIG_CAIF_NETDEV=m
    CONFIG_CAIF_USB=m
    CONFIG_CEPH_LIB=m
    # CONFIG_CEPH_LIB_PRETTYDEBUG is not set
    # CONFIG_CEPH_LIB_USE_DNS_RESOLVER is not set
    CONFIG_NFC=m
    CONFIG_NFC_NCI=m
    CONFIG_NFC_HCI=m
    # CONFIG_NFC_SHDLC is not set
    # CONFIG_NFC_LLCP is not set
    # Near Field Communication (NFC) devices
    CONFIG_NFC_PN533=m
    CONFIG_NFC_WILINK=m
    CONFIG_NFC_PN544=m
    CONFIG_NFC_MICROREAD=m
    # Device Drivers
    # Generic Driver Options
    CONFIG_UEVENT_HELPER_PATH=""
    CONFIG_DEVTMPFS=y
    # CONFIG_DEVTMPFS_MOUNT is not set
    CONFIG_STANDALONE=y
    CONFIG_PREVENT_FIRMWARE_BUILD=y
    CONFIG_FW_LOADER=y
    CONFIG_FIRMWARE_IN_KERNEL=y
    CONFIG_EXTRA_FIRMWARE=""
    # CONFIG_FW_LOADER_USER_HELPER is not set
    # CONFIG_DEBUG_DRIVER is not set
    # CONFIG_DEBUG_DEVRES is not set
    # CONFIG_SYS_HYPERVISOR is not set
    # CONFIG_GENERIC_CPU_DEVICES is not set
    CONFIG_REGMAP=y
    CONFIG_REGMAP_I2C=m
    CONFIG_REGMAP_MMIO=m
    CONFIG_REGMAP_IRQ=y
    CONFIG_DMA_SHARED_BUFFER=y
    # CONFIG_CMA is not set
    # Bus devices
    CONFIG_CONNECTOR=y
    CONFIG_PROC_EVENTS=y
    CONFIG_MTD=m
    CONFIG_MTD_TESTS=m
    CONFIG_MTD_REDBOOT_PARTS=m
    CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
    # CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
    # CONFIG_MTD_REDBOOT_PARTS_READONLY is not set
    CONFIG_MTD_CMDLINE_PARTS=m
    CONFIG_MTD_OF_PARTS=m
    CONFIG_MTD_AR7_PARTS=m
    # User Modules And Translation Layers
    CONFIG_MTD_CHAR=m
    CONFIG_MTD_BLKDEVS=m
    CONFIG_MTD_BLOCK=m
    CONFIG_MTD_BLOCK_RO=m
    CONFIG_FTL=m
    CONFIG_NFTL=m
    CONFIG_NFTL_RW=y
    CONFIG_INFTL=m
    CONFIG_RFD_FTL=m
    CONFIG_SSFDC=m
    # CONFIG_SM_FTL is not set
    CONFIG_MTD_OOPS=m
    CONFIG_MTD_SWAP=m
    # RAM/ROM/Flash chip drivers
    CONFIG_MTD_CFI=m
    CONFIG_MTD_JEDECPROBE=m
    CONFIG_MTD_GEN_PROBE=m
    # CONFIG_MTD_CFI_ADV_OPTIONS is not set
    CONFIG_MTD_MAP_BANK_WIDTH_1=y
    CONFIG_MTD_MAP_BANK_WIDTH_2=y
    CONFIG_MTD_MAP_BANK_WIDTH_4=y
    # CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
    # CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
    # CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
    CONFIG_MTD_CFI_I1=y
    CONFIG_MTD_CFI_I2=y
    # CONFIG_MTD_CFI_I4 is not set
    # CONFIG_MTD_CFI_I8 is not set
    CONFIG_MTD_CFI_INTELEXT=m
    CONFIG_MTD_CFI_AMDSTD=m
    CONFIG_MTD_CFI_STAA=m
    CONFIG_MTD_CFI_UTIL=m
    CONFIG_MTD_RAM=m
    CONFIG_MTD_ROM=m
    CONFIG_MTD_ABSENT=m
    # Mapping drivers for chip access
    CONFIG_MTD_COMPLEX_MAPPINGS=y
    # CONFIG_MTD_PHYSMAP is not set
    CONFIG_MTD_PHYSMAP_OF=m
    CONFIG_MTD_SC520CDP=m
    CONFIG_MTD_NETSC520=m
    CONFIG_MTD_TS5500=m
    # CONFIG_MTD_SBC_GXX is not set
    # CONFIG_MTD_AMD76XROM is not set
    # CONFIG_MTD_ICHXROM is not set
    # CONFIG_MTD_ESB2ROM is not set
    # CONFIG_MTD_CK804XROM is not set
    CONFIG_MTD_SCB2_FLASH=m
    # CONFIG_MTD_NETtel is not set
    # CONFIG_MTD_L440GX is not set
    CONFIG_MTD_PCI=m
    # CONFIG_MTD_PCMCIA is not set
    # CONFIG_MTD_GPIO_ADDR is not set
    # CONFIG_MTD_INTEL_VR_NOR is not set
    CONFIG_MTD_PLATRAM=m
    # CONFIG_MTD_LATCH_ADDR is not set
    # Self-contained MTD device drivers
    CONFIG_MTD_PMC551=m
    # CONFIG_MTD_PMC551_BUGFIX is not set
    # CONFIG_MTD_PMC551_DEBUG is not set
    # CONFIG_MTD_DATAFLASH is not set
    # CONFIG_MTD_M25P80 is not set
    # CONFIG_MTD_SST25L is not set
    # CONFIG_MTD_SLRAM is not set
    CONFIG_MTD_PHRAM=m
    CONFIG_MTD_MTDRAM=m
    CONFIG_MTDRAM_TOTAL_SIZE=4096
    CONFIG_MTDRAM_ERASE_SIZE=128
    CONFIG_MTD_BLOCK2MTD=m
    # Disk-On-Chip Device Drivers
    # CONFIG_MTD_DOC2000 is not set
    # CONFIG_MTD_DOC2001 is not set
    # CONFIG_MTD_DOC2001PLUS is not set
    CONFIG_MTD_DOCG3=m
    CONFIG_BCH_CONST_M=14
    CONFIG_BCH_CONST_T=4
    CONFIG_MTD_NAND_ECC=m
    CONFIG_MTD_NAND_ECC_SMC=y
    CONFIG_MTD_NAND=m
    # CONFIG_MTD_NAND_ECC_BCH is not set
    CONFIG_MTD_SM_COMMON=m
    # CONFIG_MTD_NAND_MUSEUM_IDS is not set
    # CONFIG_MTD_NAND_DENALI is not set
    CONFIG_MTD_NAND_IDS=m
    CONFIG_MTD_NAND_RICOH=m
    CONFIG_MTD_NAND_DISKONCHIP=m
    # CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED is not set
    CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0
    # CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE is not set
    CONFIG_MTD_NAND_DOCG4=m
    # CONFIG_MTD_NAND_CAFE is not set
    CONFIG_MTD_NAND_CS553X=m
    CONFIG_MTD_NAND_NANDSIM=m
    # CONFIG_MTD_NAND_PLATFORM is not set
    CONFIG_MTD_ALAUDA=m
    # CONFIG_MTD_ONENAND is not set
    # LPDDR flash memory drivers
    CONFIG_MTD_LPDDR=m
    CONFIG_MTD_QINFO_PROBE=m
    CONFIG_MTD_UBI=m
    CONFIG_MTD_UBI_WL_THRESHOLD=4096
    CONFIG_MTD_UBI_BEB_LIMIT=20
    # CONFIG_MTD_UBI_FASTMAP is not set
    # CONFIG_MTD_UBI_GLUEBI is not set
    CONFIG_OF=y
    # Device Tree and Open Firmware support
    CONFIG_PROC_DEVICETREE=y
    # CONFIG_OF_SELFTEST is not set
    CONFIG_OF_PROMTREE=y
    CONFIG_OF_ADDRESS=y
    CONFIG_OF_IRQ=y
    CONFIG_OF_DEVICE=y
    CONFIG_OF_I2C=m
    CONFIG_OF_NET=y
    CONFIG_OF_MDIO=m
    CONFIG_OF_PCI=y
    CONFIG_OF_PCI_IRQ=y
    CONFIG_OF_MTD=y
    CONFIG_PARPORT=m
    CONFIG_PARPORT_PC=m
    CONFIG_PARPORT_SERIAL=m
    # CONFIG_PARPORT_PC_FIFO is not set
    # CONFIG_PARPORT_PC_SUPERIO is not set
    CONFIG_PARPORT_PC_PCMCIA=m
    # CONFIG_PARPORT_GSC is not set
    CONFIG_PARPORT_AX88796=m
    CONFIG_PARPORT_1284=y
    CONFIG_PARPORT_NOT_PC=y
    CONFIG_PNP=y
    # CONFIG_PNP_DEBUG_MESSAGES is not set
    # Protocols
    CONFIG_ISAPNP=y
    # CONFIG_PNPBIOS is not set
    CONFIG_PNPACPI=y
    CONFIG_BLK_DEV=y
    CONFIG_BLK_DEV_FD=m
    # CONFIG_PARIDE is not set
    CONFIG_BLK_DEV_PCIESSD_MTIP32XX=m
    CONFIG_BLK_CPQ_DA=m
    CONFIG_BLK_CPQ_CISS_DA=m
    # CONFIG_CISS_SCSI_TAPE is not set
    CONFIG_BLK_DEV_DAC960=m
    # CONFIG_BLK_DEV_UMEM is not set
    # CONFIG_BLK_DEV_COW_COMMON is not set
    CONFIG_BLK_DEV_LOOP=m
    CONFIG_BLK_DEV_LOOP_MIN_COUNT=8
    CONFIG_BLK_DEV_CRYPTOLOOP=m
    CONFIG_BLK_DEV_DRBD=m
    # CONFIG_DRBD_FAULT_INJECTION is not set
    CONFIG_BLK_DEV_NBD=m
    CONFIG_BLK_DEV_NVME=m
    CONFIG_BLK_DEV_OSD=m
    CONFIG_BLK_DEV_SX8=m
    CONFIG_BLK_DEV_RAM=m
    CONFIG_BLK_DEV_RAM_COUNT=16
    CONFIG_BLK_DEV_RAM_SIZE=16384
    # CONFIG_BLK_DEV_XIP is not set
    CONFIG_CDROM_PKTCDVD=m
    CONFIG_CDROM_PKTCDVD_BUFFERS=8
    # CONFIG_CDROM_PKTCDVD_WCACHE is not set
    CONFIG_ATA_OVER_ETH=m
    CONFIG_VIRTIO_BLK=m
    # CONFIG_BLK_DEV_HD is not set
    CONFIG_BLK_DEV_RBD=m
    CONFIG_BLK_DEV_RSXX=m
    # Misc devices
    CONFIG_SENSORS_LIS3LV02D=m
    CONFIG_AD525X_DPOT=m
    CONFIG_AD525X_DPOT_I2C=m
    # CONFIG_AD525X_DPOT_SPI is not set
    # CONFIG_IBM_ASM is not set
    CONFIG_PHANTOM=m
    CONFIG_INTEL_MID_PTI=m
    CONFIG_SGI_IOC4=m
    CONFIG_TIFM_CORE=m
    CONFIG_TIFM_7XX1=m
    CONFIG_ICS932S401=m
    # CONFIG_ATMEL_SSC is not set
    CONFIG_ENCLOSURE_SERVICES=m
    CONFIG_CS5535_MFGPT=m
    CONFIG_CS5535_MFGPT_DEFAULT_IRQ=7
    CONFIG_CS5535_CLOCK_EVENT_SRC=m
    CONFIG_HP_ILO=m
    CONFIG_APDS9802ALS=m
    CONFIG_ISL29003=m
    CONFIG_ISL29020=m
    CONFIG_SENSORS_TSL2550=m
    CONFIG_SENSORS_BH1780=m
    CONFIG_SENSORS_BH1770=m
    CONFIG_SENSORS_APDS990X=m
    CONFIG_HMC6352=m
    CONFIG_DS1682=m
    # CONFIG_TI_DAC7512 is not set
    CONFIG_VMWARE_BALLOON=m
    CONFIG_BMP085=y
    CONFIG_BMP085_I2C=m
    # CONFIG_BMP085_SPI is not set
    # CONFIG_PCH_PHUB is not set
    CONFIG_USB_SWITCH_FSA9480=m
    # CONFIG_LATTICE_ECP3_CONFIG is not set
    CONFIG_C2PORT=m
    CONFIG_C2PORT_DURAMAR_2150=m
    # EEPROM support
    CONFIG_EEPROM_AT24=m
    # CONFIG_EEPROM_AT25 is not set
    CONFIG_EEPROM_LEGACY=m
    CONFIG_EEPROM_MAX6875=m
    CONFIG_EEPROM_93CX6=m
    # CONFIG_EEPROM_93XX46 is not set
    CONFIG_CB710_CORE=m
    # CONFIG_CB710_DEBUG is not set
    CONFIG_CB710_DEBUG_ASSUMPTIONS=y
    # Texas Instruments shared transport line discipline
    CONFIG_TI_ST=m
    CONFIG_SENSORS_LIS3_I2C=m
    # Altera FPGA firmware download module
    CONFIG_ALTERA_STAPL=m
    CONFIG_INTEL_MEI=m
    CONFIG_INTEL_MEI_ME=y
    CONFIG_VMWARE_VMCI=m
    CONFIG_HAVE_IDE=y
    # CONFIG_IDE is not set
    # SCSI device support
    CONFIG_SCSI_MOD=m
    CONFIG_RAID_ATTRS=m
    CONFIG_SCSI=m
    CONFIG_SCSI_DMA=y
    CONFIG_SCSI_TGT=m
    CONFIG_SCSI_NETLINK=y
    CONFIG_SCSI_PROC_FS=y
    # SCSI support type (disk, tape, CD-ROM)
    CONFIG_BLK_DEV_SD=m
    CONFIG_CHR_DEV_ST=m
    CONFIG_CHR_DEV_OSST=m
    CONFIG_BLK_DEV_SR=m
    CONFIG_BLK_DEV_SR_VENDOR=y
    CONFIG_CHR_DEV_SG=m
    CONFIG_CHR_DEV_SCH=m
    CONFIG_SCSI_ENCLOSURE=m
    CONFIG_SCSI_MULTI_LUN=y
    # CONFIG_SCSI_CONSTANTS is not set
    # CONFIG_SCSI_LOGGING is not set
    # CONFIG_SCSI_SCAN_ASYNC is not set
    # SCSI Transports
    CONFIG_SCSI_SPI_ATTRS=m
    CONFIG_SCSI_FC_ATTRS=m
    # CONFIG_SCSI_FC_TGT_ATTRS is not set
    CONFIG_SCSI_ISCSI_ATTRS=m
    CONFIG_SCSI_SAS_ATTRS=m
    CONFIG_SCSI_SAS_LIBSAS=m
    CONFIG_SCSI_SAS_ATA=y
    CONFIG_SCSI_SAS_HOST_SMP=y
    CONFIG_SCSI_SRP_ATTRS=m
    CONFIG_SCSI_SRP_TGT_ATTRS=y
    CONFIG_SCSI_LOWLEVEL=y
    CONFIG_ISCSI_TCP=m
    CONFIG_ISCSI_BOOT_SYSFS=m
    CONFIG_SCSI_CXGB3_ISCSI=m
    CONFIG_SCSI_CXGB4_ISCSI=m
    CONFIG_SCSI_BNX2_ISCSI=m
    CONFIG_SCSI_BNX2X_FCOE=m
    CONFIG_BE2ISCSI=m
    CONFIG_BLK_DEV_3W_XXXX_RAID=m
    CONFIG_SCSI_HPSA=m
    CONFIG_SCSI_3W_9XXX=m
    CONFIG_SCSI_3W_SAS=m
    CONFIG_SCSI_7000FASST=m
    CONFIG_SCSI_ACARD=m
    CONFIG_SCSI_AHA152X=m
    CONFIG_SCSI_AHA1542=m
    CONFIG_SCSI_AACRAID=m
    CONFIG_SCSI_AIC7XXX=m
    CONFIG_AIC7XXX_CMDS_PER_DEVICE=32
    CONFIG_AIC7XXX_RESET_DELAY_MS=15000
    # CONFIG_AIC7XXX_DEBUG_ENABLE is not set
    CONFIG_AIC7XXX_DEBUG_MASK=0
    CONFIG_AIC7XXX_REG_PRETTY_PRINT=y
    # CONFIG_SCSI_AIC7XXX_OLD is not set
    CONFIG_SCSI_AIC79XX=m
    CONFIG_AIC79XX_CMDS_PER_DEVICE=32
    CONFIG_AIC79XX_RESET_DELAY_MS=15000
    # CONFIG_AIC79XX_DEBUG_ENABLE is not set
    CONFIG_AIC79XX_DEBUG_MASK=0
    CONFIG_AIC79XX_REG_PRETTY_PRINT=y
    CONFIG_SCSI_AIC94XX=m
    # CONFIG_AIC94XX_DEBUG is not set
    CONFIG_SCSI_MVSAS=m
    # CONFIG_SCSI_MVSAS_DEBUG is not set
    CONFIG_SCSI_MVSAS_TASKLET=y
    CONFIG_SCSI_MVUMI=m
    CONFIG_SCSI_DPT_I2O=m
    CONFIG_SCSI_ADVANSYS=m
    CONFIG_SCSI_IN2000=m
    CONFIG_SCSI_ARCMSR=m
    CONFIG_MEGARAID_NEWGEN=y
    CONFIG_MEGARAID_MM=m
    CONFIG_MEGARAID_MAILBOX=m
    CONFIG_MEGARAID_LEGACY=m
    CONFIG_MEGARAID_SAS=m
    CONFIG_SCSI_MPT2SAS=m
    CONFIG_SCSI_MPT2SAS_MAX_SGE=128
    # CONFIG_SCSI_MPT2SAS_LOGGING is not set
    CONFIG_SCSI_MPT3SAS=m
    CONFIG_SCSI_MPT3SAS_MAX_SGE=128
    CONFIG_SCSI_MPT3SAS_LOGGING=y
    CONFIG_SCSI_UFSHCD=m
    CONFIG_SCSI_UFSHCD_PCI=m
    CONFIG_SCSI_HPTIOP=m
    CONFIG_SCSI_BUSLOGIC=m
    # CONFIG_SCSI_FLASHPOINT is not set
    CONFIG_VMWARE_PVSCSI=m
    CONFIG_HYPERV_STORAGE=m
    CONFIG_LIBFC=m
    CONFIG_LIBFCOE=m
    CONFIG_FCOE=m
    CONFIG_FCOE_FNIC=m
    CONFIG_SCSI_DMX3191D=m
    CONFIG_SCSI_DTC3280=m
    CONFIG_SCSI_EATA=m
    # CONFIG_SCSI_EATA_TAGGED_QUEUE is not set
    # CONFIG_SCSI_EATA_LINKED_COMMANDS is not set
    CONFIG_SCSI_EATA_MAX_TAGS=16
    CONFIG_SCSI_FUTURE_DOMAIN=m
    CONFIG_SCSI_GDTH=m
    CONFIG_SCSI_ISCI=m
    CONFIG_SCSI_GENERIC_NCR5380=m
    CONFIG_SCSI_GENERIC_NCR5380_MMIO=m
    CONFIG_SCSI_GENERIC_NCR53C400=y
    CONFIG_SCSI_IPS=m
    CONFIG_SCSI_INITIO=m
    CONFIG_SCSI_INIA100=m
    CONFIG_SCSI_PPA=m
    CONFIG_SCSI_IMM=m
    # CONFIG_SCSI_IZIP_EPP16 is not set
    # CONFIG_SCSI_IZIP_SLOW_CTR is not set
    CONFIG_SCSI_NCR53C406A=m
    CONFIG_SCSI_STEX=m
    CONFIG_SCSI_SYM53C8XX_2=m
    CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
    CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
    CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
    CONFIG_SCSI_SYM53C8XX_MMIO=y
    CONFIG_SCSI_IPR=m
    # CONFIG_SCSI_IPR_TRACE is not set
    # CONFIG_SCSI_IPR_DUMP is not set
    CONFIG_SCSI_PAS16=m
    CONFIG_SCSI_QLOGIC_FAS=m
    CONFIG_SCSI_QLOGIC_1280=m
    CONFIG_SCSI_QLA_FC=m
    CONFIG_TCM_QLA2XXX=m
    CONFIG_SCSI_QLA_ISCSI=m
    CONFIG_SCSI_LPFC=m
    # CONFIG_SCSI_LPFC_DEBUG_FS is not set
    CONFIG_SCSI_SYM53C416=m
    CONFIG_SCSI_DC395x=m
    CONFIG_SCSI_DC390T=m
    CONFIG_SCSI_T128=m
    CONFIG_SCSI_U14_34F=m
    # CONFIG_SCSI_U14_34F_TAGGED_QUEUE is not set
    # CONFIG_SCSI_U14_34F_LINKED_COMMANDS is not set
    CONFIG_SCSI_U14_34F_MAX_TAGS=8
    CONFIG_SCSI_ULTRASTOR=m
    CONFIG_SCSI_NSP32=m
    # CONFIG_SCSI_DEBUG is not set
    CONFIG_SCSI_PMCRAID=m
    CONFIG_SCSI_PM8001=m
    CONFIG_SCSI_SRP=m
    CONFIG_SCSI_BFA_FC=m
    CONFIG_SCSI_VIRTIO=m
    CONFIG_SCSI_CHELSIO_FCOE=m
    CONFIG_SCSI_LOWLEVEL_PCMCIA=y
    CONFIG_PCMCIA_AHA152X=m
    CONFIG_PCMCIA_FDOMAIN=m
    CONFIG_PCMCIA_NINJA_SCSI=m
    CONFIG_PCMCIA_QLOGIC=m
    CONFIG_PCMCIA_SYM53C500=m
    CONFIG_SCSI_DH=m
    CONFIG_SCSI_DH_RDAC=m
    CONFIG_SCSI_DH_HP_SW=m
    CONFIG_SCSI_DH_EMC=m
    CONFIG_SCSI_DH_ALUA=m
    CONFIG_SCSI_OSD_INITIATOR=m
    CONFIG_SCSI_OSD_ULD=m
    CONFIG_SCSI_OSD_DPRINT_SENSE=0
    # CONFIG_SCSI_OSD_DEBUG is not set
    CONFIG_ATA=m
    # CONFIG_ATA_NONSTANDARD is not set
    CONFIG_ATA_VERBOSE_ERROR=y
    CONFIG_ATA_ACPI=y
    CONFIG_SATA_ZPODD=y
    CONFIG_SATA_PMP=y
    # Controllers with non-SFF native interface
    CONFIG_SATA_AHCI=m
    CONFIG_SATA_AHCI_PLATFORM=m
    CONFIG_SATA_INIC162X=m
    CONFIG_SATA_ACARD_AHCI=m
    CONFIG_SATA_SIL24=m
    CONFIG_ATA_SFF=y
    # SFF controllers with custom DMA interface
    CONFIG_PDC_ADMA=m
    CONFIG_SATA_QSTOR=m
    CONFIG_SATA_SX4=m
    CONFIG_ATA_BMDMA=y
    # SATA SFF controllers with BMDMA
    CONFIG_ATA_PIIX=m
    CONFIG_SATA_HIGHBANK=m
    CONFIG_SATA_MV=m
    CONFIG_SATA_NV=m
    CONFIG_SATA_PROMISE=m
    CONFIG_SATA_SIL=m
    CONFIG_SATA_SIS=m
    CONFIG_SATA_SVW=m
    CONFIG_SATA_ULI=m
    CONFIG_SATA_VIA=m
    CONFIG_SATA_VITESSE=m
    # PATA SFF controllers with BMDMA
    CONFIG_PATA_ALI=m
    CONFIG_PATA_AMD=m
    CONFIG_PATA_ARASAN_CF=m
    CONFIG_PATA_ARTOP=m
    CONFIG_PATA_ATIIXP=m
    CONFIG_PATA_ATP867X=m
    CONFIG_PATA_CMD64X=m
    CONFIG_PATA_CS5520=m
    CONFIG_PATA_CS5530=m
    CONFIG_PATA_CS5535=m
    CONFIG_PATA_CS5536=m
    CONFIG_PATA_CYPRESS=m
    CONFIG_PATA_EFAR=m
    CONFIG_PATA_HPT366=m
    CONFIG_PATA_HPT37X=m
    CONFIG_PATA_HPT3X2N=m
    CONFIG_PATA_HPT3X3=m
    # CONFIG_PATA_HPT3X3_DMA is not set
    CONFIG_PATA_IT8213=m
    CONFIG_PATA_IT821X=m
    CONFIG_PATA_JMICRON=m
    CONFIG_PATA_MARVELL=m
    CONFIG_PATA_NETCELL=m
    CONFIG_PATA_NINJA32=m
    CONFIG_PATA_NS87415=m
    CONFIG_PATA_OLDPIIX=m
    CONFIG_PATA_OPTIDMA=m
    CONFIG_PATA_PDC2027X=m
    CONFIG_PATA_PDC_OLD=m
    CONFIG_PATA_RADISYS=m
    CONFIG_PATA_RDC=m
    CONFIG_PATA_SC1200=m
    CONFIG_PATA_SCH=m
    CONFIG_PATA_SERVERWORKS=m
    CONFIG_PATA_SIL680=m
    CONFIG_PATA_SIS=m
    CONFIG_PATA_TOSHIBA=m
    CONFIG_PATA_TRIFLEX=m
    CONFIG_PATA_VIA=m
    CONFIG_PATA_WINBOND=m
    # PIO-only SFF controllers
    CONFIG_PATA_CMD640_PCI=m
    CONFIG_PATA_ISAPNP=m
    CONFIG_PAT

    xf86-video-intel?  I tried putting that in /etc/default/grub 
    $ cat /etc/default/grub
    GRUB_DEFAULT=0
    GRUB_TIMEOUT=5
    GRUB_DISTRIBUTOR="Arch"
    GRUB_CMDLINE_LINUX_DEFAULT="i915.modeset=1"
    GRUB_CMDLINE_LINUX=""
    # Preload both GPT and MBR modules so that they are not missed
    GRUB_PRELOAD_MODULES="part_gpt part_msdos"
    # Uncomment to enable Hidden Menu, and optionally hide the timeout count
    GRUB_HIDDEN_TIMEOUT=0
    #GRUB_HIDDEN_TIMEOUT_QUIET=true
    # Uncomment to use basic console
    GRUB_TERMINAL_INPUT=console
    # Uncomment to disable graphical terminal
    #GRUB_TERMINAL_OUTPUT=console
    # The resolution used on graphical terminal
    # note that you can use only modes which your graphic card supports via VBE
    # you can see them in real GRUB with the command `vbeinfo'
    GRUB_GFXMODE=auto
    # Uncomment to allow the kernel use the same resolution used by grub
    GRUB_GFXPAYLOAD_LINUX=keep
    # Uncomment if you want GRUB to pass to the Linux kernel the old parameter
    # format "root=/dev/xxx" instead of "root=/dev/disk/by-uuid/xxx"
    #GRUB_DISABLE_LINUX_UUID=true
    # Uncomment to disable generation of recovery mode menu entries
    GRUB_DISABLE_RECOVERY=true
    # Uncomment and set to the desired menu colors. Used by normal and wallpaper
    # modes only. Entries specified as foreground/background.
    #GRUB_COLOR_NORMAL="light-blue/black"
    #GRUB_COLOR_HIGHLIGHT="light-cyan/blue"
    # Uncomment one of them for the gfx desired, a image background or a gfxtheme
    #GRUB_BACKGROUND="/path/to/wallpaper"
    #GRUB_THEME="/path/to/gfxtheme"
    # Uncomment to get a beep at GRUB start
    #GRUB_INIT_TUNE="480 440 1"
    #GRUB_SAVEDEFAULT="true"
    according to the link I need to add it to /etc/mkinitcpio.conf
    I added it and got this error during build::
    ==> ERROR: module not found: `i915.modeset=1'
    so I reverted it back to i915 and I am wondering about the warnings during build
    ==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'default'
    -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux.img
    ==> Starting build: 3.9.9-1-ARCH
    -> Running build hook: [base]
    -> Running build hook: [udev]
    -> Running build hook: [autodetect]
    -> Running build hook: [modconf]
    -> Running build hook: [block]
    -> Running build hook: [resume]
    -> Running build hook: [filesystems]
    -> Running build hook: [keyboard]
    -> Running build hook: [fsck]
    ==> Generating module dependencies
    ==> Creating gzip initcpio image: /boot/initramfs-linux.img
    ==> Image generation successful
    ==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'fallback'
    -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux-fallback.img -S autodetect
    ==> Starting build: 3.9.9-1-ARCH
    -> Running build hook: [base]
    -> Running build hook: [udev]
    -> Running build hook: [modconf]
    -> Running build hook: [block]
    ==> WARNING: Possibly missing firmware for module: aic94xx
    ==> WARNING: Possibly missing firmware for module: bfa
    -> Running build hook: [resume]
    -> Running build hook: [filesystems]
    -> Running build hook: [keyboard]
    -> Running build hook: [fsck]
    ==> Generating module dependencies
    ==> Creating gzip initcpio image: /boot/initramfs-linux-fallback.img
    ==> Image generation successful
    Last edited by Areckx (2013-07-10 20:37:39)

  • Sometimes it doesn't resume from suspend

    Hey! As you may guess (!), I'm new to this. But I love the idea of learning.
    Anyway, I have a laptop Acer Aspire 7741G-6426 and I'm having a little problem. See, I first installed XFCE4 with SLIM as a WM, the problem was that I couldn't resume from suspend (or sleep), all I got was a black screen. After that, I enabled autologin to XFCE, and just to tried one more time, I suspended, and the problem was 'solved'. I could resume without problems.
    I'm on a fresh install now, with KDE and the same problem happened before I enabled autologin in KDM (before enabling it, the same problem described above occurred). I can suspend and resume. That is, most of the time. An hour ago I suspended the laptop, and my surprise was to find the black screen again when trying to resume. When I resumed, the disk seemed to load something and then stopped and all I could see was a black screen, the same as before. The only thing I can do when that happens is to hard shutdown the PC.
    A few minutes ago I tried again, and resumed without problems. But I'm afraid it might happen again and I might lose something important. I need to find a solution.
    Also, I have an AMD 6550M video card and I'm using the Catalyst driver (because the open source made the laptop too hot).
    I don't know if this is related, but if I run "lsmod | grep radeon", this is the output:
    radeon 989731 0
    ttm 54560 1 radeon
    drm_kms_helper 27529 1 radeon
    drm 181991 3 radeon,ttm,drm_kms_helper
    i2c_algo_bit 5239 1 radeon
    i2c_core 20165 6 videodev,radeon,drm_kms_helper,drm,i2c_algo_bit,i2c_i801
    Is it normal that the radeon driver is loaded? Isn't that the open source one, which I didn't installed?
    Anyway, does anyone have any idea of what this is?
    I don't know what kind of information I should give.
    Oh, and I've been reading some logs (which I'm making myself believe I can understand, haha), and in pm-suspend.log, almost everything says "resume suspend: success", except for:
    Running hook /etc/pm/sleep.d/90alsa resume suspend:
    ALSA lib pulse.c:229:(pulse_connect) PulseAudio: Unable to connect: Connection refused
    aplay: main:660: audio open error: Connection refused
    In kernel.log, there are many (specially 'dhcpcd not running'):
    Jun 29 20:03:43 localhost kernel: [ 8233.952493] ath: txq: ffff88012c2068d0 axq_qnum: 2, mac80211_qnum: 2 axq_link: ffff8800bac25ea8 pending frames: 1 axq_acq empty: 1 stopped: 0 axq_depth: 0 Attempting to restart tx logic.
    Jun 29 23:34:01 localhost kernel: [ 6.727474] intel ips 0000:00:1f.6: failed to get i915 symbols, graphics turbo disabled
    Jun 29 23:34:01 localhost kernel: [ 6.904533] acer_wmi: Unable to detect available WMID devices
    Jun 29 23:34:14 localhost dhcpcd[955]: dhcpcd not running
    Jun 29 23:34:30 localhost pulseaudio[1155]: pid.c: Daemon already running.
    And also, sorry for my english (and such a long post)!
    Thanks anyway.

    After so many days without the problem, I got the black screen of death minutes ago. I suspended and about 40 minutes later tried to resume and got the black screen. At least this time the wifi led was on and the disk seemed more active than other times. Though unfortunately I couldn't ssh into the laptop since I didn't have sshd enabled... But I could use the SysRq key, and for the first time, I got the "ASIC hang happened". I'm thinking that this might have something to do with the "nopat" line. Since before I added this line, the wifi led was off, there was no disk activity (past the first 3-4 seconds when trying to resume) and the SysRq key wouldn't work, so I had to hard shutdown. So at least now the SysRq key works, that's something.
    This is the full log from the failed resume:
    Jul 14 23:46:20 localhost kernel: [ 8505.476150] PM: Syncing filesystems ... done.
    Jul 14 23:46:20 localhost kernel: [ 8505.477733] PM: Preparing system for mem sleep
    Jul 14 23:46:20 localhost kernel: [ 8505.477749] Freezing user space processes ... (elapsed 0.01 seconds) done.
    Jul 14 23:46:20 localhost kernel: [ 8505.488608] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
    Jul 14 23:46:20 localhost kernel: [ 8505.501902] PM: Entering mem sleep
    Jul 14 23:46:20 localhost kernel: [ 8505.502003] Suspending console(s) (use no_console_suspend to debug)
    Jul 14 23:46:20 localhost kernel: [ 8505.551975] sd 0:0:0:0: [sda] Synchronizing SCSI cache
    Jul 14 23:46:20 localhost kernel: [ 8505.629234] HDA Intel 0000:02:00.1: PCI INT B disabled
    Jul 14 23:46:20 localhost kernel: [ 8505.629293] ACPI handle has no context!
    Jul 14 23:46:20 localhost kernel: [ 8505.629299] ehci_hcd 0000:00:1d.0: PCI INT A disabled
    Jul 14 23:46:20 localhost kernel: [ 8505.629321] [fglrx] IRQ 44 Disabled
    Jul 14 23:46:20 localhost kernel: [ 8505.629468] [fglrx] Preparing suspend fglrx in kernel.
    Jul 14 23:46:20 localhost kernel: [ 8505.629964] ehci_hcd 0000:00:1a.0: PCI INT A disabled
    Jul 14 23:46:20 localhost kernel: [ 8505.637746] kworker/u:29: page allocation failure. order:10, mode:0x4020
    Jul 14 23:46:20 localhost kernel: [ 8505.637749] Pid: 8403, comm: kworker/u:29 Tainted: P 2.6.39-ARCH #1
    Jul 14 23:46:20 localhost kernel: [ 8505.637751] Call Trace:
    Jul 14 23:46:20 localhost kernel: [ 8505.637759] [<ffffffff810fc30f>] __alloc_pages_nodemask+0x78f/0x8c0
    Jul 14 23:46:20 localhost kernel: [ 8505.637762] [<ffffffff81132673>] alloc_pages_current+0xa3/0x110
    Jul 14 23:46:20 localhost kernel: [ 8505.637766] [<ffffffff810f821e>] __get_free_pages+0xe/0x50
    Jul 14 23:46:20 localhost kernel: [ 8505.637769] [<ffffffff8113d81f>] kmalloc_order_trace+0x3f/0x100
    Jul 14 23:46:20 localhost kernel: [ 8505.637805] [<ffffffffa06c1cf3>] ? __start_CPDMA_copy_evergreen+0xa3/0xc0 [fglrx]
    Jul 14 23:46:20 localhost kernel: [ 8505.637808] [<ffffffff8113da77>] __kmalloc+0x197/0x1a0
    Jul 14 23:46:20 localhost kernel: [ 8505.637820] [<ffffffffa069438e>] KCL_MEM_SmallBufferAllocAtomic+0x1e/0x20 [fglrx]
    Jul 14 23:46:20 localhost kernel: [ 8505.637836] [<ffffffffa06a7da3>] firegl_save_fb+0x233/0x360 [fglrx]
    Jul 14 23:46:20 localhost kernel: [ 8505.637853] [<ffffffffa06a6f35>] ? firegl_pm_save_framebuffer+0x1f5/0x280 [fglrx]
    Jul 14 23:46:20 localhost kernel: [ 8505.637869] [<ffffffffa06a9b2d>] ? firegl_cail_powerdown+0x8d/0x200 [fglrx]
    Jul 14 23:46:20 localhost kernel: [ 8505.637879] [<ffffffffa0691fc7>] ? fglrx_pci_suspend+0x87/0x150 [fglrx]
    Jul 14 23:46:20 localhost kernel: [ 8505.637884] [<ffffffff812390f6>] ? pci_legacy_suspend+0x46/0xe0
    Jul 14 23:46:20 localhost kernel: [ 8505.637886] [<ffffffff8123a3ad>] ? pci_pm_suspend+0xdd/0x130
    Jul 14 23:46:20 localhost kernel: [ 8505.637890] [<ffffffff812e5b35>] ? pm_op+0x175/0x1c0
    Jul 14 23:46:20 localhost kernel: [ 8505.637892] [<ffffffff812e5c32>] ? __device_suspend+0xb2/0x1a0
    Jul 14 23:46:20 localhost kernel: [ 8505.637896] [<ffffffff81085b50>] ? async_schedule+0x20/0x20
    Jul 14 23:46:20 localhost kernel: [ 8505.637898] [<ffffffff812e5d41>] ? async_suspend+0x21/0x50
    Jul 14 23:46:20 localhost kernel: [ 8505.637900] [<ffffffff81085bcf>] ? async_run_entry_fn+0x7f/0x180
    Jul 14 23:46:20 localhost kernel: [ 8505.637903] [<ffffffff81077f6e>] ? process_one_work+0x11e/0x4c0
    Jul 14 23:46:20 localhost kernel: [ 8505.637905] [<ffffffff810788ff>] ? worker_thread+0x15f/0x350
    Jul 14 23:46:20 localhost kernel: [ 8505.637907] [<ffffffff810787a0>] ? manage_workers.isra.29+0x230/0x230
    Jul 14 23:46:20 localhost kernel: [ 8505.637909] [<ffffffff8107d6ec>] ? kthread+0x8c/0xa0
    Jul 14 23:46:20 localhost kernel: [ 8505.637912] [<ffffffff813e9fe4>] ? kernel_thread_helper+0x4/0x10
    Jul 14 23:46:20 localhost kernel: [ 8505.637914] [<ffffffff8107d660>] ? kthread_worker_fn+0x190/0x190
    Jul 14 23:46:20 localhost kernel: [ 8505.637915] [<ffffffff813e9fe0>] ? gs_change+0x13/0x13
    Jul 14 23:46:20 localhost kernel: [ 8505.637917] Mem-Info:
    Jul 14 23:46:20 localhost kernel: [ 8505.637918] Node 0 DMA per-cpu:
    Jul 14 23:46:20 localhost kernel: [ 8505.637919] CPU 0: hi: 0, btch: 1 usd: 0
    Jul 14 23:46:20 localhost kernel: [ 8505.637921] CPU 1: hi: 0, btch: 1 usd: 0
    Jul 14 23:46:20 localhost kernel: [ 8505.637922] CPU 2: hi: 0, btch: 1 usd: 0
    Jul 14 23:46:20 localhost kernel: [ 8505.637923] CPU 3: hi: 0, btch: 1 usd: 0
    Jul 14 23:46:20 localhost kernel: [ 8505.637924] Node 0 DMA32 per-cpu:
    Jul 14 23:46:20 localhost kernel: [ 8505.637925] CPU 0: hi: 186, btch: 31 usd: 18
    Jul 14 23:46:20 localhost kernel: [ 8505.637927] CPU 1: hi: 186, btch: 31 usd: 185
    Jul 14 23:46:20 localhost kernel: [ 8505.637928] CPU 2: hi: 186, btch: 31 usd: 1
    Jul 14 23:46:20 localhost kernel: [ 8505.637929] CPU 3: hi: 186, btch: 31 usd: 45
    Jul 14 23:46:20 localhost kernel: [ 8505.637930] Node 0 Normal per-cpu:
    Jul 14 23:46:20 localhost kernel: [ 8505.637931] CPU 0: hi: 186, btch: 31 usd: 185
    Jul 14 23:46:20 localhost kernel: [ 8505.637932] CPU 1: hi: 186, btch: 31 usd: 158
    Jul 14 23:46:20 localhost kernel: [ 8505.637934] CPU 2: hi: 186, btch: 31 usd: 151
    Jul 14 23:46:20 localhost kernel: [ 8505.637935] CPU 3: hi: 186, btch: 31 usd: 44
    Jul 14 23:46:20 localhost kernel: [ 8505.637938] active_anon:264255 inactive_anon:50599 isolated_anon:0
    Jul 14 23:46:20 localhost kernel: [ 8505.637939] active_file:81821 inactive_file:445828 isolated_file:0
    Jul 14 23:46:20 localhost kernel: [ 8505.637939] unevictable:0 dirty:11 writeback:0 unstable:0
    Jul 14 23:46:20 localhost kernel: [ 8505.637940] free:33258 slab_reclaimable:12432 slab_unreclaimable:5104
    Jul 14 23:46:20 localhost kernel: [ 8505.637941] mapped:66993 shmem:1158 pagetables:7761 bounce:0
    Jul 14 23:46:20 localhost kernel: [ 8505.637942] Node 0 DMA free:15780kB min:264kB low:328kB high:396kB active_anon:0kB inactive_anon:64kB active_file:0kB inactive_file:0kB unevictable:0kB isolated(anon):0kB isolated(file):0kB present:15676kB mlocked:0kB dirty:0kB writeback:0kB mapped:0kB shmem:0kB slab_reclaimable:0kB slab_unreclaimable:8kB kernel_stack:0kB pagetables:48kB unstable:0kB bounce:0kB writeback_tmp:0kB pages_scanned:0 all_unreclaimable? no
    Jul 14 23:46:20 localhost kernel: [ 8505.637948] lowmem_reserve[]: 0 2989 3872 3872
    Jul 14 23:46:20 localhost kernel: [ 8505.637950] Node 0 DMA32 free:98084kB min:51956kB low:64944kB high:77932kB active_anon:912996kB inactive_anon:57860kB active_file:243344kB inactive_file:1551960kB unevictable:0kB isolated(anon):0kB isolated(file):0kB present:3060784kB mlocked:0kB dirty:24kB writeback:0kB mapped:64464kB shmem:3904kB slab_reclaimable:30264kB slab_unreclaimable:2868kB kernel_stack:632kB pagetables:9772kB unstable:0kB bounce:0kB writeback_tmp:0kB pages_scanned:0 all_unreclaimable? no
    Jul 14 23:46:20 localhost kernel: [ 8505.637956] lowmem_reserve[]: 0 0 883 883
    Jul 14 23:46:20 localhost kernel: [ 8505.637958] Node 0 Normal free:19168kB min:15360kB low:19200kB high:23040kB active_anon:144024kB inactive_anon:144472kB active_file:83940kB inactive_file:231352kB unevictable:0kB isolated(anon):0kB isolated(file):0kB present:904960kB mlocked:0kB dirty:20kB writeback:0kB mapped:203508kB shmem:728kB slab_reclaimable:19464kB slab_unreclaimable:17540kB kernel_stack:2064kB pagetables:21224kB unstable:0kB bounce:0kB writeback_tmp:0kB pages_scanned:0 all_unreclaimable? no
    Jul 14 23:46:20 localhost kernel: [ 8505.637964] lowmem_reserve[]: 0 0 0 0
    Jul 14 23:46:20 localhost kernel: [ 8505.637965] Node 0 DMA: 1*4kB 0*8kB 0*16kB 1*32kB 2*64kB 2*128kB 2*256kB 1*512kB 2*1024kB 2*2048kB 2*4096kB = 15780kB
    Jul 14 23:46:20 localhost kernel: [ 8505.637970] Node 0 DMA32: 3368*4kB 1866*8kB 1033*16kB 584*32kB 119*64kB 45*128kB 20*256kB 9*512kB 9*1024kB 1*2048kB 0*4096kB = 97984kB
    Jul 14 23:46:20 localhost kernel: [ 8505.637974] Node 0 Normal: 88*4kB 179*8kB 357*16kB 133*32kB 32*64kB 4*128kB 3*256kB 4*512kB 0*1024kB 1*2048kB 0*4096kB = 19176kB
    Jul 14 23:46:20 localhost kernel: [ 8505.637978] 528820 total pagecache pages
    Jul 14 23:46:20 localhost kernel: [ 8505.637979] 0 pages in swap cache
    Jul 14 23:46:20 localhost kernel: [ 8505.637981] Swap cache stats: add 8, delete 8, find 0/0
    Jul 14 23:46:20 localhost kernel: [ 8505.637982] Free swap = 4000116kB
    Jul 14 23:46:20 localhost kernel: [ 8505.637982] Total swap = 4000148kB
    Jul 14 23:46:20 localhost kernel: [ 8505.648067] 1015792 pages RAM
    Jul 14 23:46:20 localhost kernel: [ 8505.648069] 95954 pages reserved
    Jul 14 23:46:20 localhost kernel: [ 8505.648069] 452085 pages shared
    Jul 14 23:46:20 localhost kernel: [ 8505.648070] 604505 pages non-shared
    Jul 14 23:46:20 localhost kernel: [ 8505.648107] sd 0:0:0:0: [sda] Stopping disk
    Jul 14 23:46:20 localhost kernel: [ 8505.731612] HDA Intel 0000:00:1b.0: PCI INT A disabled
    Jul 14 23:46:20 localhost kernel: [ 8505.893374] [fglrx] Suspending fglrx in kernel completed.
    Jul 14 23:46:20 localhost kernel: [ 8505.893377] [fglrx] Power down the ASIC .
    Jul 14 23:46:20 localhost kernel: [ 8506.356479] PM: suspend of devices complete after 843.272 msecs
    Jul 14 23:46:20 localhost kernel: [ 8506.409696] PM: late suspend of devices complete after 53.343 msecs
    Jul 14 23:46:20 localhost kernel: [ 8506.409993] ACPI: Preparing to enter system sleep state S3
    Jul 14 23:46:20 localhost kernel: [ 8506.526263] PM: Saving platform NVS memory
    Jul 14 23:46:20 localhost kernel: [ 8506.528060] Disabling non-boot CPUs ...
    Jul 14 23:46:20 localhost kernel: [ 8506.672249] CPU 1 is now offline
    Jul 14 23:46:20 localhost kernel: [ 8506.805254] CPU 2 is now offline
    Jul 14 23:46:20 localhost kernel: [ 8506.931586] CPU 3 is now offline
    Jul 14 23:46:20 localhost kernel: [ 8506.931924] Extended CMOS year: 2000
    Jul 14 23:46:20 localhost kernel: [ 8506.932121] ACPI: Low-level resume complete
    Jul 14 23:46:20 localhost kernel: [ 8506.932167] PM: Restoring platform NVS memory
    Jul 14 23:46:20 localhost kernel: [ 8506.932608] Extended CMOS year: 2000
    Jul 14 23:46:20 localhost kernel: [ 8506.932626] Enabling non-boot CPUs ...
    Jul 14 23:46:20 localhost kernel: [ 8506.939427] Booting Node 0 Processor 1 APIC 0x4
    Jul 14 23:46:20 localhost kernel: [ 8506.939430] smpboot cpu 1: start_ip = 97000
    Jul 14 23:46:20 localhost kernel: [ 8507.055234] Switched to NOHz mode on CPU #1
    Jul 14 23:46:20 localhost kernel: [ 8507.095325] NMI watchdog enabled, takes one hw-pmu counter.
    Jul 14 23:46:20 localhost kernel: [ 8507.095442] CPU1 is up
    Jul 14 23:46:20 localhost kernel: [ 8507.095504] Booting Node 0 Processor 2 APIC 0x1
    Jul 14 23:46:20 localhost kernel: [ 8507.095505] smpboot cpu 2: start_ip = 97000
    Jul 14 23:46:20 localhost kernel: [ 8507.211565] Switched to NOHz mode on CPU #2
    Jul 14 23:46:20 localhost kernel: [ 8507.251738] NMI watchdog enabled, takes one hw-pmu counter.
    Jul 14 23:46:20 localhost kernel: [ 8507.251873] CPU2 is up
    Jul 14 23:46:20 localhost kernel: [ 8507.251962] Booting Node 0 Processor 3 APIC 0x5
    Jul 14 23:46:20 localhost kernel: [ 8507.251964] smpboot cpu 3: start_ip = 97000
    Jul 14 23:46:20 localhost kernel: [ 8507.367843] Switched to NOHz mode on CPU #3
    Jul 14 23:46:20 localhost kernel: [ 8507.408173] NMI watchdog enabled, takes one hw-pmu counter.
    Jul 14 23:46:20 localhost kernel: [ 8507.408519] CPU3 is up
    Jul 14 23:46:20 localhost kernel: [ 8507.410477] ACPI: Waking up from system sleep state S3
    Jul 14 23:46:20 localhost kernel: [ 8507.484393] power_supply BAT0: parent PNP0C0A:00 should not be sleeping
    Jul 14 23:46:20 localhost kernel: [ 8507.597538] pcieport 0000:00:01.0: restoring config space at offset 0xf (was 0x80100, writing 0x8010b)
    Jul 14 23:46:20 localhost kernel: [ 8507.597543] pcieport 0000:00:01.0: restoring config space at offset 0x7 (was 0x2020, writing 0x20002020)
    Jul 14 23:46:20 localhost kernel: [ 8507.597547] pcieport 0000:00:01.0: restoring config space at offset 0x3 (was 0x10000, writing 0x10010)
    Jul 14 23:46:20 localhost kernel: [ 8507.597550] pcieport 0000:00:01.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100507)
    Jul 14 23:46:20 localhost kernel: [ 8507.597595] ehci_hcd 0000:00:1a.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
    Jul 14 23:46:20 localhost kernel: [ 8507.597608] ehci_hcd 0000:00:1a.0: restoring config space at offset 0x4 (was 0x0, writing 0xf0606000)
    Jul 14 23:46:20 localhost kernel: [ 8507.597613] ehci_hcd 0000:00:1a.0: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900102)
    Jul 14 23:46:20 localhost kernel: [ 8507.597635] HDA Intel 0000:00:1b.0: restoring config space at offset 0xf (was 0x100, writing 0x107)
    Jul 14 23:46:20 localhost kernel: [ 8507.597646] HDA Intel 0000:00:1b.0: restoring config space at offset 0x4 (was 0xdc000004, writing 0xf0600004)
    Jul 14 23:46:20 localhost kernel: [ 8507.597650] HDA Intel 0000:00:1b.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
    Jul 14 23:46:20 localhost kernel: [ 8507.597654] HDA Intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100006, writing 0x100102)
    Jul 14 23:46:20 localhost kernel: [ 8507.597673] pcieport 0000:00:1c.0: restoring config space at offset 0xf (was 0x100, writing 0x4010a)
    Jul 14 23:46:20 localhost kernel: [ 8507.597680] pcieport 0000:00:1c.0: restoring config space at offset 0x9 (was 0x10001, writing 0xf011f001)
    Jul 14 23:46:20 localhost kernel: [ 8507.597683] pcieport 0000:00:1c.0: restoring config space at offset 0x8 (was 0x0, writing 0xf020f020)
    Jul 14 23:46:20 localhost kernel: [ 8507.597687] pcieport 0000:00:1c.0: restoring config space at offset 0x7 (was 0x0, writing 0x3030)
    Jul 14 23:46:20 localhost kernel: [ 8507.597690] pcieport 0000:00:1c.0: restoring config space at offset 0x6 (was 0x0, writing 0x40300)
    Jul 14 23:46:20 localhost kernel: [ 8507.597694] pcieport 0000:00:1c.0: restoring config space at offset 0x3 (was 0x810000, writing 0x810010)
    Jul 14 23:46:20 localhost kernel: [ 8507.597698] pcieport 0000:00:1c.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
    Jul 14 23:46:20 localhost kernel: [ 8507.597721] pcieport 0000:00:1c.1: restoring config space at offset 0xf (was 0x200, writing 0x4020b)
    Jul 14 23:46:20 localhost kernel: [ 8507.597728] pcieport 0000:00:1c.1: restoring config space at offset 0x9 (was 0x10001, writing 0xc011c001)
    Jul 14 23:46:20 localhost kernel: [ 8507.597731] pcieport 0000:00:1c.1: restoring config space at offset 0x8 (was 0x0, writing 0xf030f030)
    Jul 14 23:46:20 localhost kernel: [ 8507.597734] pcieport 0000:00:1c.1: restoring config space at offset 0x7 (was 0x0, writing 0x4040)
    Jul 14 23:46:20 localhost kernel: [ 8507.597737] pcieport 0000:00:1c.1: restoring config space at offset 0x6 (was 0x0, writing 0x50500)
    Jul 14 23:46:20 localhost kernel: [ 8507.597742] pcieport 0000:00:1c.1: restoring config space at offset 0x3 (was 0x810000, writing 0x810010)
    Jul 14 23:46:20 localhost kernel: [ 8507.597746] pcieport 0000:00:1c.1: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
    Jul 14 23:46:20 localhost kernel: [ 8507.597768] ehci_hcd 0000:00:1d.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
    Jul 14 23:46:20 localhost kernel: [ 8507.597781] ehci_hcd 0000:00:1d.0: restoring config space at offset 0x4 (was 0x0, writing 0xf0607000)
    Jul 14 23:46:20 localhost kernel: [ 8507.597786] ehci_hcd 0000:00:1d.0: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900102)
    Jul 14 23:46:20 localhost kernel: [ 8507.597803] pci 0000:00:1e.0: restoring config space at offset 0xf (was 0x40000, writing 0x400ff)
    Jul 14 23:46:20 localhost kernel: [ 8507.597810] pci 0000:00:1e.0: restoring config space at offset 0x9 (was 0x10001, writing 0x1fff1)
    Jul 14 23:46:20 localhost kernel: [ 8507.597813] pci 0000:00:1e.0: restoring config space at offset 0x8 (was 0x0, writing 0xfff0)
    Jul 14 23:46:20 localhost kernel: [ 8507.597816] pci 0000:00:1e.0: restoring config space at offset 0x7 (was 0x22800000, writing 0x228000f0)
    Jul 14 23:46:20 localhost kernel: [ 8507.597823] pci 0000:00:1e.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
    Jul 14 23:46:20 localhost kernel: [ 8507.597868] ahci 0000:00:1f.2: restoring config space at offset 0xf (was 0x200, writing 0x205)
    Jul 14 23:46:20 localhost kernel: [ 8507.597880] ahci 0000:00:1f.2: restoring config space at offset 0x1 (was 0x2b00007, writing 0x2b00407)
    Jul 14 23:46:20 localhost kernel: [ 8507.597921] pci 0000:00:1f.6: restoring config space at offset 0xf (was 0x300, writing 0x30a)
    Jul 14 23:46:20 localhost kernel: [ 8507.597936] pci 0000:00:1f.6: restoring config space at offset 0x1 (was 0x100000, writing 0x100002)
    Jul 14 23:46:20 localhost kernel: [ 8507.597958] fglrx_pci 0000:02:00.0: restoring config space at offset 0xf (was 0x1ff, writing 0x10b)
    Jul 14 23:46:20 localhost kernel: [ 8507.597967] fglrx_pci 0000:02:00.0: restoring config space at offset 0x8 (was 0x1, writing 0x2001)
    Jul 14 23:46:20 localhost kernel: [ 8507.597971] fglrx_pci 0000:02:00.0: restoring config space at offset 0x6 (was 0x4, writing 0xcfee0004)
    Jul 14 23:46:20 localhost kernel: [ 8507.597975] fglrx_pci 0000:02:00.0: restoring config space at offset 0x4 (was 0xc, writing 0xd000000c)
    Jul 14 23:46:20 localhost kernel: [ 8507.597978] fglrx_pci 0000:02:00.0: restoring config space at offset 0x3 (was 0x800000, writing 0x800010)
    Jul 14 23:46:20 localhost kernel: [ 8507.597982] fglrx_pci 0000:02:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100503)
    Jul 14 23:46:20 localhost kernel: [ 8507.598013] HDA Intel 0000:02:00.1: restoring config space at offset 0xf (was 0x2ff, writing 0x20a)
    Jul 14 23:46:20 localhost kernel: [ 8507.598024] HDA Intel 0000:02:00.1: restoring config space at offset 0x4 (was 0x4, writing 0xcfedc004)
    Jul 14 23:46:20 localhost kernel: [ 8507.598028] HDA Intel 0000:02:00.1: restoring config space at offset 0x3 (was 0x800000, writing 0x800010)
    Jul 14 23:46:20 localhost kernel: [ 8507.598032] HDA Intel 0000:02:00.1: restoring config space at offset 0x1 (was 0x100000, writing 0x100103)
    Jul 14 23:46:20 localhost kernel: [ 8507.598116] tg3 0000:03:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
    Jul 14 23:46:20 localhost kernel: [ 8507.598121] tg3 0000:03:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100506)
    Jul 14 23:46:20 localhost kernel: [ 8507.598178] ath9k 0000:05:00.0: restoring config space at offset 0xf (was 0x1ff, writing 0x10a)
    Jul 14 23:46:20 localhost kernel: [ 8507.598196] ath9k 0000:05:00.0: restoring config space at offset 0x4 (was 0x4, writing 0xf0300004)
    Jul 14 23:46:20 localhost kernel: [ 8507.598200] ath9k 0000:05:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
    Jul 14 23:46:20 localhost kernel: [ 8507.598205] ath9k 0000:05:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
    Jul 14 23:46:20 localhost kernel: [ 8507.598413] PM: early resume of devices complete after 0.957 msecs
    Jul 14 23:46:20 localhost kernel: [ 8507.598692] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    Jul 14 23:46:20 localhost kernel: [ 8507.598700] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
    Jul 14 23:46:20 localhost kernel: [ 8507.598705] ehci_hcd 0000:00:1a.0: setting latency timer to 64
    Jul 14 23:46:20 localhost kernel: [ 8507.598708] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
    Jul 14 23:46:20 localhost kernel: [ 8507.598711] HDA Intel 0000:00:1b.0: setting latency timer to 64
    Jul 14 23:46:20 localhost kernel: [ 8507.598715] ehci_hcd 0000:00:1d.0: setting latency timer to 64
    Jul 14 23:46:20 localhost kernel: [ 8507.598746] pci 0000:00:1e.0: setting latency timer to 64
    Jul 14 23:46:20 localhost kernel: [ 8507.598753] HDA Intel 0000:00:1b.0: irq 42 for MSI/MSI-X
    Jul 14 23:46:20 localhost kernel: [ 8507.598765] [fglrx] Kernel supports PAT but it has been disabled
    Jul 14 23:46:20 localhost kernel: [ 8507.598766] [fglrx] Using driver built-in PAT support instead
    Jul 14 23:46:20 localhost kernel: [ 8507.598768] ahci 0000:00:1f.2: setting latency timer to 64
    Jul 14 23:46:20 localhost kernel: [ 8507.599319] tg3 0000:03:00.0: wake-up capability disabled by ACPI
    Jul 14 23:46:20 localhost kernel: [ 8507.599360] tg3 0000:03:00.0: PME# disabled
    Jul 14 23:46:20 localhost kernel: [ 8507.599505] HDA Intel 0000:02:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    Jul 14 23:46:20 localhost kernel: [ 8507.599515] HDA Intel 0000:02:00.1: setting latency timer to 64
    Jul 14 23:46:20 localhost kernel: [ 8507.599554] HDA Intel 0000:02:00.1: irq 43 for MSI/MSI-X
    Jul 14 23:46:20 localhost kernel: [ 8507.599630] sd 0:0:0:0: [sda] Starting disk
    Jul 14 23:46:20 localhost kernel: [ 8507.599912] fglrx_pci 0000:02:00.0: setting latency timer to 64
    Jul 14 23:46:20 localhost kernel: [ 8507.605625] [fglrx] Power up the ASIC
    Jul 14 23:46:20 localhost kernel: [ 8507.605752] [fglrx] Preparing resume fglrx in kernel.
    Jul 14 23:46:20 localhost kernel: [ 8507.673839] [fglrx] Resuming fglrx in kernel completed.
    Jul 14 23:46:20 localhost kernel: [ 8507.674036] [fglrx] IRQ 44 Enabled
    Jul 14 23:46:20 localhost kernel: [ 8507.850159] usb 2-1.5: reset high speed USB device number 3 using ehci_hcd
    Jul 14 23:46:20 localhost kernel: [ 8507.916491] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    Jul 14 23:46:20 localhost kernel: [ 8507.919985] ata5.00: configured for UDMA/100
    Jul 14 23:46:20 localhost kernel: [ 8510.054456] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    Jul 14 23:46:20 localhost kernel: [ 8510.258470] ata1.00: configured for UDMA/133
    Jul 14 23:46:20 localhost kernel: [ 8510.336104] PM: resume of devices complete after 2744.342 msecs
    Jul 14 23:46:20 localhost kernel: [ 8510.336358] PM: Finishing wakeup.
    Jul 14 23:46:20 localhost kernel: [ 8510.336359] Restarting tasks ... done.
    Jul 14 23:46:20 localhost kernel: [ 8510.344265] video LNXVIDEO:00: Restoring backlight state
    Jul 14 23:46:21 localhost kernel: [ 8511.289064] tg3 0000:03:00.0: eth0: Link is down
    Jul 14 23:46:23 localhost kernel: [ 8513.177532] EXT4-fs (sda5): re-mounted. Opts: commit=0
    Jul 14 23:46:24 localhost kernel: [ 8513.797702] EXT4-fs (sda6): re-mounted. Opts: commit=0
    Jul 14 23:46:24 localhost kernel: [ 8514.034086] tg3 0000:03:00.0: PME# enabled
    Jul 14 23:46:24 localhost kernel: [ 8514.034101] tg3 0000:03:00.0: wake-up capability enabled by ACPI
    Jul 14 23:46:24 localhost kernel: [ 8514.057819] tg3 0000:03:00.0: irq 45 for MSI/MSI-X
    Jul 14 23:46:24 localhost kernel: [ 8514.291538] tg3 0000:03:00.0: eth0: Link is down
    Jul 14 23:46:26 localhost kernel: [ 8516.531715] wlan0: authenticate with 00:1b:11:a3:7b:24 (try 1)
    Jul 14 23:46:26 localhost kernel: [ 8516.533596] wlan0: authenticated
    Jul 14 23:46:26 localhost kernel: [ 8516.533615] wlan0: associate with 00:1b:11:a3:7b:24 (try 1)
    Jul 14 23:46:26 localhost kernel: [ 8516.536019] wlan0: RX AssocResp from 00:1b:11:a3:7b:24 (capab=0x431 status=0 aid=3)
    Jul 14 23:46:26 localhost kernel: [ 8516.536021] wlan0: associated
    Jul 14 23:49:21 localhost kernel: [ 8690.305910] [fglrx] ASIC hang happened
    Jul 14 23:49:21 localhost kernel: [ 8690.305915] Pid: 820, comm: X Tainted: P 2.6.39-ARCH #1
    Jul 14 23:49:21 localhost kernel: [ 8690.305917] Call Trace:
    Jul 14 23:49:21 localhost kernel: [ 8690.305955] [<ffffffffa0698d5e>] KCL_DEBUG_OsDump+0xe/0x10 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.305972] [<ffffffffa06a618c>] firegl_hardwareHangRecovery+0x1c/0x50 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306004] [<ffffffffa072d419>] ? _ZN4Asic9WaitUntil15ResetASICIfHungEv+0x9/0x10 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306034] [<ffffffffa072d3cc>] ? _ZN4Asic9WaitUntil15WaitForCompleteEv+0x6c/0xb0 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306050] [<ffffffffa0779d7f>] ? _ZN13BaseUVDEngineI18mmEngineRS780_UVD2E4idleEv+0x7f/0xc0 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306081] [<ffffffffa072c55c>] ? _ZN15ExecutableUnits35flush_all_and_invalidate_HDP_cachesE12_QS_CP_RING_+0xbc/0xe0 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306112] [<ffffffffa072c355>] ? _ZN15ExecutableUnits10CPRingIdleE15idle_WaitMethod12_QS_CP_RING_+0x105/0x1a0 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306143] [<ffffffffa0736807>] ? _ZN11AsicCypress21initializeMicroEngineEv+0x147/0x160 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306158] [<ffffffffa077a026>] ? _ZN13BaseUVDEngineI18mmEngineRS780_UVD2E14SwitchEngineHWEN8mmEngine15MM_ENGINE_STATEE+0x26/0x1d0 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306190] [<ffffffffa072733a>] ? _ZN18mmEnginesContainer13assertEnginesEb+0x5a/0xa0 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306220] [<ffffffffa072be78>] ? _ZN15ExecutableUnits17assertPrimaryRingEb+0x1f8/0x210 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306251] [<ffffffffa073372a>] ? _ZN8AsicR6009assertPM4Eb+0x4a/0x70 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306270] [<ffffffffa06c3350>] ? firegl_cmmqs_disabledriver+0xf0/0xf0 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306299] [<ffffffffa07080aa>] ? CMMQS_ReinitializeHardware+0x6a/0x80 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306318] [<ffffffffa06c43e0>] ? firegl_cmmqs_Enable_QS+0x70/0x110 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306337] [<ffffffffa06c3370>] ? firegl_cmmqs_enableqs+0x20/0x90 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306349] [<ffffffffa0694256>] ? KCL_PosixSecurityCapCheck+0x26/0x30 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306365] [<ffffffffa06a1d98>] ? firegl_ioctl+0x1e8/0x250 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306369] [<ffffffff8118ae62>] ? fsnotify+0x1c2/0x2a0
    Jul 14 23:49:21 localhost kernel: [ 8690.306380] [<ffffffffa0692eae>] ? ip_firegl_unlocked_ioctl+0xe/0x20 [fglrx]
    Jul 14 23:49:21 localhost kernel: [ 8690.306385] [<ffffffff81163b6f>] ? do_vfs_ioctl+0x8f/0x500
    Jul 14 23:49:21 localhost kernel: [ 8690.306389] [<ffffffff81151f48>] ? vfs_write+0x148/0x180
    Jul 14 23:49:21 localhost kernel: [ 8690.306391] [<ffffffff81164071>] ? sys_ioctl+0x91/0xa0
    Jul 14 23:49:21 localhost kernel: [ 8690.306396] [<ffffffff813e8ec2>] ? system_call_fastpath+0x16/0x1b
    Jul 14 23:49:21 localhost kernel: [ 8690.306399] pubdev:0xffffffffa08da080, num of device:1 , name:fglrx, major 8, minor 86.
    Jul 14 23:49:21 localhost kernel: [ 8690.306402] device 0 : 0xffff88012c40c000 .
    Jul 14 23:49:21 localhost kernel: [ 8690.306403] Asic ID:0x68c1, revision:0x28, MMIOReg:0xffffc900117c0000.
    Jul 14 23:49:21 localhost kernel: [ 8690.306405] FB phys addr: 0xd0000000, MC :0xf00000000, Total FB size :0x40000000.
    Jul 14 23:49:21 localhost kernel: [ 8690.306407] gart table MC:0xf0f941000, Physical:0xdf941000, size:0x3be000.
    Jul 14 23:49:21 localhost kernel: [ 8690.306410] mc_node :FB, total 1 zones
    Jul 14 23:49:21 localhost kernel: [ 8690.306411] MC start:0xf00000000, Physical:0xd0000000, size:0xfd00000.
    Jul 14 23:49:21 localhost kernel: [ 8690.306414] Mapped heap -- Offset:0x0, size:0xf941000, reference count:120, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306416] Mapped heap -- Offset:0x0, size:0x1000000, reference count:1, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306418] Mapped heap -- Offset:0xf941000, size:0x3bf000, reference count:1, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306419] mc_node :INV_FB, total 1 zones
    Jul 14 23:49:21 localhost kernel: [ 8690.306421] MC start:0xf0fd00000, Physical:0xdfd00000, size:0x30300000.
    Jul 14 23:49:21 localhost kernel: [ 8690.306423] Mapped heap -- Offset:0x302f4000, size:0xc000, reference count:1, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306424] mc_node :GART_USWC, total 2 zones
    Jul 14 23:49:21 localhost kernel: [ 8690.306426] MC start:0x3ce90000, Physical:0x0, size:0x4ac00000.
    Jul 14 23:49:21 localhost kernel: [ 8690.306428] Mapped heap -- Offset:0x5030000, size:0x800000, reference count:1, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306430] Mapped heap -- Offset:0x4830000, size:0x800000, reference count:1, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306432] Mapped heap -- Offset:0x4030000, size:0x800000, reference count:1, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306434] Mapped heap -- Offset:0x3830000, size:0x800000, reference count:1, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306436] Mapped heap -- Offset:0x3030000, size:0x800000, reference count:1, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306438] Mapped heap -- Offset:0x2830000, size:0x800000, reference count:1, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306440] Mapped heap -- Offset:0x2030000, size:0x800000, reference count:1, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306442] Mapped heap -- Offset:0x30000, size:0x2000000, reference count:13, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306444] mc_node :GART_CACHEABLE, total 3 zones
    Jul 14 23:49:21 localhost kernel: [ 8690.306445] MC start:0x10400000, Physical:0x0, size:0x2ca90000.
    Jul 14 23:49:21 localhost kernel: [ 8690.306447] Mapped heap -- Offset:0x8100000, size:0x700000, reference count:2, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306449] Mapped heap -- Offset:0x3f00000, size:0x600000, reference count:1, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306451] Mapped heap -- Offset:0x5800000, size:0x700000, reference count:2, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306453] Mapped heap -- Offset:0x5100000, size:0x700000, reference count:2, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306455] Mapped heap -- Offset:0x7b00000, size:0x600000, reference count:1, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306457] Mapped heap -- Offset:0x7500000, size:0x600000, reference count:2, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306459] Mapped heap -- Offset:0x6f00000, size:0x600000, reference count:2, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306461] Mapped heap -- Offset:0x6900000, size:0x600000, reference count:2, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306463] Mapped heap -- Offset:0x6300000, size:0x600000, reference count:2, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306465] Mapped heap -- Offset:0x4500000, size:0x600000, reference count:2, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306467] Mapped heap -- Offset:0x4d00000, size:0x400000, reference count:2, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306469] Mapped heap -- Offset:0x3c00000, size:0x300000, reference count:2, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306471] Mapped heap -- Offset:0x3500000, size:0x700000, reference count:3, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306473] Mapped heap -- Offset:0x2e00000, size:0x700000, reference count:2, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306475] Mapped heap -- Offset:0x2700000, size:0x700000, reference count:3, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306477] Mapped heap -- Offset:0x2300000, size:0x400000, reference count:5, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306479] Mapped heap -- Offset:0x1f00000, size:0x400000, reference count:6, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306481] Mapped heap -- Offset:0x1b00000, size:0x400000, reference count:5, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306483] Mapped heap -- Offset:0x1700000, size:0x400000, reference count:3, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306485] Mapped heap -- Offset:0x1000000, size:0x700000, reference count:17, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306487] Mapped heap -- Offset:0x900000, size:0x700000, reference count:16, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306489] Mapped heap -- Offset:0x200000, size:0x700000, reference count:40, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306491] Mapped heap -- Offset:0x0, size:0x200000, reference count:16, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306494] Mapped heap -- Offset:0xef000, size:0x11000, reference count:1, mapping count:0,
    Jul 14 23:49:21 localhost kernel: [ 8690.306552] GRBM : 0x3828, SRBM : 0x200000c0 .
    Jul 14 23:49:21 localhost kernel: [ 8690.306555] CP_RB_BASE : 0x3cec00, CP_RB_RPTR : 0x20 , CP_RB_WPTR :0x20.
    Jul 14 23:49:21 localhost kernel: [ 8690.306558] CP_IB1_BUFSZ:0x0, CP_IB1_BASE_HI:0x0, CP_IB1_BASE_LO:0x0.
    Jul 14 23:49:21 localhost kernel: [ 8690.306560] last submit IB buffer -- MC :0x0. Can't found mapped physical page for this MC .
    Jul 14 23:49:21 localhost kernel: [ 8690.306561] Dump the trace queue.
    Jul 14 23:49:21 localhost kernel: [ 8690.306562] End of dump
    Too bad we still don't know what's the cause... and why it seemed to be fine for so many days.
    Update: Well, this is weird and worse and perhaps related. The first time that this happened to me was a few days ago. After 15 minutes of inactivity, the screen turns off, to save power, well, I think this is the third time that, when returning to the laptop and attempting to turn the screen back on, it doesn't. It's like the same thing that happens when resuming from sleep mode, the black screen.
    I checked the logs, and in everything.log, these are the only entries from about that time:
    Jul 15 18:03:01 localhost crond[820]: FILE /var/spool/cron/root USER root PID 12357 job sys-hourly
    Jul 15 18:08:13 localhost kernel: [13935.470836] ath: txq: ffff88013002e8d0 axq_qnum: 2, mac80211_qnum: 2 axq_link: ffff88003782c160 pending frames: 1 axq_acq empty: 1 stopped: 0 axq_depth: 0 Attempting to restart tx logic.
    Jul 15 18:15:44 localhost -- MARK --
    Jul 15 18:32:02 localhost kernel: [15360.917332] SysRq : Keyboard mode set to system default
    Jul 15 18:32:50 localhost kernel: [15408.634134] SysRq : Terminate All Tasks
    Oh, this is so confusing, haha.
    Last edited by AnnS (2011-07-15 23:18:49)

  • Resuming from suspend breaks function key on laptop

    I have an Asus K40IN laptop.  Up until a few days ago, suspending worked perfectly.  However, now when I resume from suspend, my function key no longer works.  I use it for some global shortcuts like play/pause, volume up/down, brightness up/down, etc.  I checked in xev, and it's actually registering no key press at all.  However, if I press it twice quickly, it will start registering infinite presses of the d key (keycode 43).  This also completely incapacitates the keyboard -- many keys do not do what they should.  It stops if I press the actual d key once.
    I'm guessing the most likely cause is a recent update.  Here's my recent /var/log/pacman.log:
    [2010-01-08 14:45] upgraded kernel26-firmware (2.6.32.2-2 -> 2.6.32.3-1)
    [2010-01-08 14:45] >>> Updating module dependencies. Please wait ...
    [2010-01-08 14:45] >>> MKINITCPIO SETUP
    [2010-01-08 14:45] >>> ----------------
    [2010-01-08 14:45] >>> If you use LVM2, Encrypted root or software RAID,
    [2010-01-08 14:45] >>> Ensure you enable support in /etc/mkinitcpio.conf .
    [2010-01-08 14:45] >>> More information about mkinitcpio setup can be found here:
    [2010-01-08 14:45] >>> http://wiki.archlinux.org/index.php/Mkinitcpio
    [2010-01-08 14:45]
    [2010-01-08 14:45] >>> Generating initial ramdisk, using mkinitcpio. Please wait...
    [2010-01-08 14:45] ==> Building image "default"
    [2010-01-08 14:45] ==> Running command: /sbin/mkinitcpio -k 2.6.32-ARCH -c /etc/mkinitcpio.conf -g /boot/kernel26.img
    [2010-01-08 14:45] :: Begin build
    [2010-01-08 14:45] :: Parsing hook [base]
    [2010-01-08 14:45] :: Parsing hook [udev]
    [2010-01-08 14:45] :: Parsing hook [autodetect]
    [2010-01-08 14:45] :: Parsing hook [pata]
    [2010-01-08 14:45] :: Parsing hook [scsi]
    [2010-01-08 14:45] :: Parsing hook [sata]
    [2010-01-08 14:45] :: Parsing hook [lvm2]
    [2010-01-08 14:45] :: Parsing hook [filesystems]
    [2010-01-08 14:45] :: Generating module dependencies
    [2010-01-08 14:45] :: Generating image '/boot/kernel26.img'...SUCCESS
    [2010-01-08 14:45] ==> SUCCESS
    [2010-01-08 14:45] ==> Building image "fallback"
    [2010-01-08 14:45] ==> Running command: /sbin/mkinitcpio -k 2.6.32-ARCH -c /etc/mkinitcpio.conf -g /boot/kernel26-fallback.img -S autodetect
    [2010-01-08 14:45] :: Begin build
    [2010-01-08 14:45] :: Parsing hook [base]
    [2010-01-08 14:45] :: Parsing hook [udev]
    [2010-01-08 14:45] :: Parsing hook [pata]
    [2010-01-08 14:46] :: Parsing hook [scsi]
    [2010-01-08 14:46] :: Parsing hook [sata]
    [2010-01-08 14:46] :: Parsing hook [lvm2]
    [2010-01-08 14:46] :: Parsing hook [filesystems]
    [2010-01-08 14:46] :: Generating module dependencies
    [2010-01-08 14:46] :: Generating image '/boot/kernel26-fallback.img'...SUCCESS
    [2010-01-08 14:46] ==> SUCCESS
    [2010-01-08 14:46] upgraded kernel26 (2.6.32.2-2 -> 2.6.32.3-1)
    [2010-01-08 14:46] upgraded zlib (1.2.3.3-3 -> 1.2.3.4-3)
    [2010-01-09 03:18] synchronizing package lists
    [2010-01-09 03:19] starting full system upgrade
    [2010-01-09 03:44] warning: /etc/arno-iptables-firewall/firewall.conf installed as /etc/arno-iptables-firewall/firewall.conf.pacnew
    [2010-01-09 03:44] upgraded arno-iptables-firewall (1.9.2g-1 -> 1.9.2h-1)
    [2010-01-09 20:46] synchronizing package lists
    [2010-01-09 20:47] starting full system upgrade
    [2010-01-09 20:47] starting full system upgrade
    [2010-01-10 03:06] synchronizing package lists
    [2010-01-10 03:06] starting full system upgrade
    [2010-01-10 03:08] In order to use the new nvidia module, exit Xserver and unload it manually.
    [2010-01-10 03:08] upgraded nvidia (190.53-1 -> 190.53-3)
    [2010-01-10 03:32] synchronizing package lists
    [2010-01-10 03:32] starting full system upgrade
    [2010-01-10 03:32] upgraded nvidia (190.53-3 -> 190.53-3)
    [2010-01-10 16:05] synchronizing package lists
    [2010-01-10 16:06] starting full system upgrade
    [2010-01-10 22:50] synchronizing package lists
    [2010-01-10 22:50] starting full system upgrade
    [2010-01-10 22:50] starting full system upgrade
    [2010-01-10 22:50] upgraded freeglut (2.4.0-4 -> 2.6.0-1)
    [2010-01-10 22:51] upgraded kid3 (1.2-1 -> 1.3-1)
    [2010-01-10 23:16] upgraded x264-git (20100107-1 -> 20100110-1)
    [2010-01-10 23:20] upgraded ffmpeg-svn (21082-1 -> 21132-1)
    [2010-01-10 23:27] upgraded mplayer-mt-git (20100107-1 -> 20100110-1)
    [2010-01-10 23:39] upgraded amarok-git (20100107-1 -> 20100110-1)
    [2010-01-10 23:39] upgraded depot_tools-svn (35767-1 -> 35900-1)
    [2010-01-11 00:25] upgraded chromium-svn (35770-1 -> 35902-1)
    [2010-01-11 02:19] installed speedcrunch (0.10.1-1)
    [2010-01-11 06:01] synchronizing package lists
    [2010-01-11 06:01] starting full system upgrade
    [2010-01-11 15:12] synchronizing package lists
    [2010-01-11 15:13] starting full system upgrade
    [2010-01-11 15:14] upgraded x264-git (20100110-1 -> 20100111-1)
    [2010-01-11 15:16] upgraded ffmpeg-svn (21132-1 -> 21152-1)
    [2010-01-11 15:19] upgraded mplayer-mt-git (20100110-1 -> 20100111-1)
    [2010-01-11 17:04] synchronizing package lists
    [2010-01-11 17:04] starting full system upgrade
    [2010-01-11 17:04] starting full system upgrade
    [2010-01-11 17:04] upgraded qtcurve-gtk2 (1.0.0-1 -> 1.0.1-1)
    [2010-01-12 15:32] synchronizing package lists
    [2010-01-12 15:33] starting full system upgrade
    [2010-01-12 15:33] starting full system upgrade
    [2010-01-12 15:34] upgraded dhcpcd (5.1.3-1 -> 5.1.4-1)
    [2010-01-12 15:34] upgraded live-media (2009.09.28-2 -> 2010.01.11-1)
    [2010-01-12 15:34] upgraded strigi (0.7.0-1 -> 0.7.1-1)
    Any ideas?

    Well I still haven't been able to fix it, but here's what I've figured out:
    - Some of the buttons (for example brightness adjust and turn screen off) do not have keycodes.  They seem to work directly through the bios, not through the operating system.  Other buttons (like volume control) do have keycodes, and do work through the OS.
    - If I unload the kernel module asus_laptop, the OS-dependent buttons stop working, but the others continue to work.
    - When I suspend and resume, all the buttons stop working.
    - Putting asus_laptop in SUSPEND_MODULES for pm-utils does not help.
    - Using s2ram from uswsusp does not help.
    - After a suspend and resume (so the buttons are all broken), when I press a button twice and start getting infinite presses of d, I get the following message in dmesg:
    Jan 17 10:45:53 firefly kernel: atkbd.c: Unknown key released (translated set 2, code 0xe1 on isa0060/serio0).
    Jan 17 10:45:53 firefly kernel: atkbd.c: Use 'setkeycodes e061 <keycode>' to make it known.
    I tried running the suggested command using a keycode for a volume button, but it didn't help.  It did stop this message from coming up in dmesg for that particular button, but the other behaviors were the same.
    I can't think of anything else to do to fix it.  Does this mean anything to anyone?

  • Resume from suspend/ibernation sometimes freeze

    When closing the lid of my laptop, my system is set to freeze.
    Sometimes when i open the lid i see the graphics turn on (on the login screen) BUT everything is frozen, even the keyboard. If i close and reopen the lid, it somehow turn back to normal.
    this message is in dmegs:
    ------------[ cut here ]------------
    [ 4366.308099] WARNING: CPU: 0 PID: 0 at drivers/gpu/drm/i915/intel_display.c:9713 intel_check_page_flip+0xda/0xf0 [i915]()
    [ 4366.308100] Kicking stuck page flip: queued at 261481, now 261490
    [ 4366.308101] Modules linked in: joydev mousedev ecb arc4 nls_iso8859_1 nls_cp437 vfat fat coretemp intel_rapl iosf_mbi x86_pkg_temp_thermal iwlmvm intel_powerclamp kvm_intel snd_hda_codec_hdmi kvm uvcvideo videobuf2_vmalloc videobuf2_memops videobuf2_core crct10dif_pclmul crc32_pclmul iTCO_wdt v4l2_common crc32c_intel btusb iTCO_vendor_support videodev amdkfd ghash_clmulni_intel mac80211 bluetooth amd_iommu_v2 media aesni_intel aes_x86_64 lrw gf128mul radeon glue_helper ablk_helper cryptd iwlwifi pcspkr evdev psmouse cfg80211 rtsx_pci_ms mac_hid r8169 sparse_keymap ttm serio_raw led_class snd_hda_codec_realtek i2c_i801 memstick ac toshiba_bluetooth thermal toshiba_haps i915 hwmon mii rfkill wmi battery snd_hda_codec_generic button video drm_kms_helper snd_hda_intel snd_hda_controller drm snd_hda_codec
    [ 4366.308125]  snd_hwdep intel_gtt snd_pcm i2c_algo_bit i2c_core snd_timer ie31200_edac snd mei_me edac_core mei lpc_ich shpchp soundcore processor sch_fq_codel nfs lockd grace sunrpc fscache ext4 crc16 mbcache jbd2 sd_mod rtsx_pci_sdmmc mmc_core atkbd libps2 ahci libahci xhci_pci ehci_pci libata xhci_hcd ehci_hcd usbcore scsi_mod rtsx_pci usb_common i8042 serio
    [ 4366.308143] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.19.3-3-ARCH #1
    [ 4366.308144] Hardware name: TOSHIBA SATELLITE P50-B-115/VG20SQ, BIOS 1.50 12/09/2014
    [ 4366.308145]  0000000000000000 886cbefc2155fb8d ffff88032fa03d18 ffffffff8155d19f
    [ 4366.308146]  0000000000000000 ffff88032fa03d70 ffff88032fa03d58 ffffffff81073a4a
    [ 4366.308147]  ffff88032fa03d58 ffff88032127c000 ffff88031f735000 ffff88031f7351a0
    [ 4366.308149] Call Trace:
    [ 4366.308150]  <IRQ>  [<ffffffff8155d19f>] dump_stack+0x4c/0x6e
    [ 4366.308159]  [<ffffffff81073a4a>] warn_slowpath_common+0x8a/0xc0
    [ 4366.308161]  [<ffffffff81073ad5>] warn_slowpath_fmt+0x55/0x70
    [ 4366.308168]  [<ffffffffa051258a>] intel_check_page_flip+0xda/0xf0 [i915]
    [ 4366.308175]  [<ffffffffa04df968>] ironlake_irq_handler+0x2e8/0xfe0 [i915]
    [ 4366.308178]  [<ffffffff812be8e0>] ? timerqueue_add+0x60/0xb0
    [ 4366.308181]  [<ffffffff810dcd69>] ? enqueue_hrtimer+0x29/0xa0
    [ 4366.308184]  [<ffffffff810cc01e>] handle_irq_event_percpu+0x3e/0x1f0
    [ 4366.308185]  [<ffffffff810cc211>] handle_irq_event+0x41/0x70
    [ 4366.308187]  [<ffffffff810cf30e>] handle_edge_irq+0x9e/0x110
    [ 4366.308191]  [<ffffffff81018242>] handle_irq+0x22/0x40
    [ 4366.308193]  [<ffffffff8156557f>] do_IRQ+0x4f/0xf0
    [ 4366.308195]  [<ffffffff8156352d>] common_interrupt+0x6d/0x6d
    [ 4366.308195]  <EOI>  [<ffffffff814215d5>] ? cpuidle_enter_state+0x65/0x190
    [ 4366.308198]  [<ffffffff814215c1>] ? cpuidle_enter_state+0x51/0x190
    [ 4366.308200]  [<ffffffff814217e7>] cpuidle_enter+0x17/0x20
    [ 4366.308201]  [<ffffffff810b4aa8>] cpu_startup_entry+0x388/0x410
    [ 4366.308203]  [<ffffffff815536b5>] rest_init+0x85/0x90
    [ 4366.308205]  [<ffffffff818fe020>] start_kernel+0x48e/0x4af
    [ 4366.308207]  [<ffffffff818fd120>] ? early_idt_handlers+0x120/0x120
    [ 4366.308208]  [<ffffffff818fd4d7>] x86_64_start_reservations+0x2a/0x2c
    [ 4366.308210]  [<ffffffff818fd62b>] x86_64_start_kernel+0x152/0x175
    [ 4366.308210] ---[ end trace e9f540c04cbb56d5 ]---

    This happens to me 100% of the time with 3.11.6 and 3.10.17, resuming from suspend results in naught but an underscore top left. VT switching appears to work temporarily, I was able to enter in my user name in the VT, but then everything hung on pressing enter. Not sure about earlier kernel versions because this is a fresh install on this hardware. Happens with and without X.
    Hibernate results in an underscore before the computer is able to shut down. I tried using pm_trace and dumping logs before/after as recommended around the internet, pm_trace didn't match any hashes & there are no logs after suspend that get written out as far as I can tell. The computer is also unresponsive to the network. I also tried using pm_debug but I wasn't really sure what I was doing, running the core test I thought shouldn't cause the computer to actually suspend, but it did & there was my underscore again in all its glory.
    Wish I knew a way to get some more information..

  • Resume from suspend occasionally fails.

    Sometimes when I resume after suspending to RAM, all that shows up is a blank screen with a single underscore at the top left. There is no mouse cursor and the system is completely unresponsive. It only happens occasionally (maybe 1/4).
    I have not found any related messages in the logs. Memtest completes successfully too. Does anyone have any idea of what might cause this?
    It's like the system is playing Russian roulette with itself whenever I resume.
    Last edited by Xyne (2013-02-06 11:54:41)

    This happens to me 100% of the time with 3.11.6 and 3.10.17, resuming from suspend results in naught but an underscore top left. VT switching appears to work temporarily, I was able to enter in my user name in the VT, but then everything hung on pressing enter. Not sure about earlier kernel versions because this is a fresh install on this hardware. Happens with and without X.
    Hibernate results in an underscore before the computer is able to shut down. I tried using pm_trace and dumping logs before/after as recommended around the internet, pm_trace didn't match any hashes & there are no logs after suspend that get written out as far as I can tell. The computer is also unresponsive to the network. I also tried using pm_debug but I wasn't really sure what I was doing, running the core test I thought shouldn't cause the computer to actually suspend, but it did & there was my underscore again in all its glory.
    Wish I knew a way to get some more information..

  • Resume from suspend broken after upgrade

    Hi, I'm having a hardware issue noone else seems to be having. I mean, I can't find any discussions or bug reports about it anywhere. :-(
    The specifics:
    Resume from suspend broke after an upgrade. X starts, windows appear, and I can move the cursor around, but everything else is frozen. The only way out is to hit C-A-F1 to switch to the virtual console and restart X or reboot.
    Please, any help will be greatly appreciated.
    I'm running:
    local/lib32-nouveau-dri 9.1.1-1
    extra/nouveau-dri 9.1.1-1
    extra/xf86-video-nouveau 1.0.7-1 (xorg-drivers xorg)
    local/linux-ck 3.8.6-1
    local/linux-ck-headers 3.8.6-1
    An extract of my Xorg.0.log during suspend/resume:
    [    43.750] (II) AIGLX: Suspending AIGLX clients for VT switch
    [    43.750] (II) NOUVEAU(0): NVLeaveVT is called.
    [    53.660] (II) AIGLX: Resuming AIGLX clients after VT switch
    [    53.660] (II) NOUVEAU(0): NVEnterVT is called.
    [    53.694] (II) NOUVEAU(0): EDID vendor "PHL", prod id 2151
    [    53.694] (II) NOUVEAU(0): Using hsync ranges from config file
    [    53.694] (II) NOUVEAU(0): Using vrefresh ranges from config file
    [    53.694] (II) NOUVEAU(0): Printing DDC gathered Modelines:
    [    53.694] (II) NOUVEAU(0): Modeline "1920x1200"x0.0  154.00  1920 1968 2000 2080  1200 1203 1209 1235 +hsync +vsync (74.0 kHz eP)
    [    53.694] (II) NOUVEAU(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "800x600"x0.0   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "640x480"x0.0   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "832x624"x0.0   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "1152x864"x60.0   81.62  1152 1216 1336 1520  864 865 868 895 -hsync +vsync (53.7 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "1280x960"x0.0  108.00  1280 1376 1488 1800  960 961 964 1000 +hsync +vsync (60.0 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "1280x720"x60.0   74.48  1280 1336 1472 1664  720 721 724 746 -hsync +vsync (44.8 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "1440x900"x0.0   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "1440x900"x0.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "1600x1200"x0.0  162.00  1600 1664 1856 2160  1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz e)
    [    53.694] (II) NOUVEAU(0): Modeline "1920x1200"x0.0  154.00  1920 1968 2000 2080  1200 1203 1209 1235 +hsync -vsync (74.0 kHz e)
    [    60.180] (II) AIGLX: Suspending AIGLX clients for VT switch
    [    60.180] (II) NOUVEAU(0): NVLeaveVT is called.
    [   131.086] (II) evdev: Logitech USB Optical Mouse: Close
    [   131.087] (II) UnloadModule: "evdev"
    [   131.087] (II) evdev: Microsoft Wired Keyboard 400: Close
    [   131.087] (II) UnloadModule: "evdev"
    [   131.087] (II) evdev: Power Button: Close
    [   131.087] (II) UnloadModule: "evdev"
    [   131.087] (II) evdev: Power Button: Close
    [   131.087] (II) UnloadModule: "evdev"
    [   131.089] (II) NOUVEAU(0): Closed GPU channel 0
    [   131.092] Server terminated successfully (0). Closing log file.
    (looks error free)

    Thank you for your reply, pyther. I figured it was a kernel bug, too, but now I'm not so sure. Surprisingly, in Ubuntu 11.04 (which uses kernel 2.6.38), suspend works fine on my laptop. Figuring that perhaps this was due to an Ubuntu-specific patch, I tried booting the 2.6.38-8-generic kernel that ships with Ubuntu 11.04 on my Arch installation, but found that it was subject to the same issue described above, where the system fails to resume from suspend. I also tried disabling laptop-mode-tools, but to no avail.
    Clearly, the problem is related somewhat to the kernel, as in my Arch installation, suspend works fine in 2.6.36, is somewhat problematic in 2.6.37, and is completely broken in 2.6.38. Yet I don't think it's entirely due to the kernel, as suspend works fine in Ubuntu 11.04, but is broken when I boot my Arch installation with Ubuntu's kernel. Performing a bit bisect to determine the bad commit sounds like it might help, but given that suspend functionality seems to have gotten progressively worse for me since 2.6.36, I'm not sure how I would go about locating a specific commit that is the source of my issues. Is there anything else I might try?

  • Pc doesn't resume from suspend to ram anymore (new 3.4.2 kernel)

    hi.
    I was using nouveau without problem and with the little trick of using acpi_os_name="Microsoft Windows NT" kernel parameter, I was able to suspend to ram from gnome, and resume the pc without problem
    Not anymore. Now, if I suspend to ram, the pc does not resume. It correctly wake up the dvd drive, the hard-drive, began to read stuff on the hdd but the led of the power button stays blinking and the screen is not waken up.
    I am thinking this is due to the update of nouveau and a new regression but this seems related to the bios or hardware. For example. If after the broken resume, I hold down 10 seconds the power button to power off, and press it again to power on, the led is still blinking and it does not boot. I need to power off by removing the power cord.
    Is it because I run (to test it) the nvida-173xx, and that did something to the graphic card ?
    Did anyone got similar problem with the new nouveau driver ?
    I tried to downgrade libgl, libdrm, libdrm-nouveau, nouveau-dri, xf86-video-nouveau and mesa but I still got the problem. so ?
    I have a geforce 8300 GS. the pc is an inspiron 531
    Last edited by solstice (2012-06-18 08:56:49)

    Probably I have the same issue with geforce GTS250.
    After upgrading to kernel 3.4.2 or so, my system doesn't resume from suspend, only black screen and cannot switch to other ttys.
    I first thought this problem be caused by the kernel, but downgrading nvidia to 295.53-2 solved this problem on kernel 3.4.3 so this likely is caused by nvidia 302.17.
    In my case there is something like error in pm-suspend.log when resume failed:
    Fri Jun 22 05:36:12 JST: Awake.
    Fri Jun 22 05:36:12 JST: Running hooks for resume
    Running hook /usr/lib/pm-utils/sleep.d/99video resume suspend:
    /usr/lib/pm-utils/sleep.d/99video resume suspend: success.
    Running hook /usr/lib/pm-utils/sleep.d/98video-quirk-db-handler resume suspend:
    /usr/lib/pm-utils/sleep.d/98video-quirk-db-handler resume suspend: success.
    Running hook /usr/lib/pm-utils/sleep.d/95led resume suspend:
    /usr/lib/pm-utils/sleep.d/95led resume suspend: success.
    Running hook /usr/lib/pm-utils/sleep.d/94cpufreq resume suspend:
    /usr/lib/pm-utils/sleep.d/94cpufreq resume suspend: success.
    Running hook /usr/lib/pm-utils/sleep.d/90clock resume suspend:
    /usr/lib/pm-utils/sleep.d/90clock resume suspend: success.
    Running hook /etc/pm/sleep.d/90alsa resume suspend:
    xcb_connection_has_error() returned true
    And curiously, if I had launched vlc media player before suspend, resume worked well even on nvidia 302.17.

  • W520 resume from suspend issue

    My W520 is about 2 years old now. Been a good machine. Lately I've had this odd issue where the W520 will not resume from suspend/sleep (not hibernation). It pretends to, but then gets stuck in an endless loop of the keyboard flashlight coming on, one of the green LED lights below the screen, and then repeating itself. This is exaclty my issue: http://www.youtube.com/watch?v=48Mi4tqUaZc
    Anyone seen this? Please don't pile on with sleep issues that are different. There are lots of similar isues, but most have different symptoms than this. Googling has shown me that this issue happens on Linux as well as Windows. 
    Thanks

    Okay, I looked at your video.  I have this exact issue too.  It started about a month ago but I am not able to pinpoint when exactly.  What version of BIOS are you running (and other specs)?
    This is frustrating!  Most days now for the past month or so, sometimes multiple  times per day, when I try to resume from sleep it fails just like you have described.  I then end up removing power and rebooting into Windows.  This typically also creates file allocation errors (and the need to check my disk).  I have gone through all of the system updates with the exception of BIOS, which is still at version 1.36.  I was going to check tonight what experience others have had with the newest BIOS.  I will post any solutions I discover.  Let me know if you find out anything.
    W520, i7-2920XM, BIOS 1.36, 1920x1080 FHD, 16GB Kingston HyperX 1600Mhz RAM, NVIDIA Quadro 2000M, WD Scorpio Black 750GB HD, Crucial mSATA 256GB, Windows 7 Pro 64-bit

  • Office 2013 - Word cannot establish a connection with this document after the system resumed from suspend mode

    Hiya!
    This issue has been answered numerous times for Office 2010 and Office 2007, but I have yet to any solutions or Hotfixes that work for Office 2013 (x64) on Win7.
    How to replicate the issue:
    Open a file from a network share.
    Edit file.
    Leave computer on with file open. Computer goes to sleep or into stand-by mode.
    Wait a bit
    Wake up computer
    CPU opens file in Read-Only mode and gives you the following error "Word cannot establish a network connection with this document after the system resumed from suspend mode. Save the document into a different file to keep any changes."
    What I've tried:
    http://support.microsoft.com/kb/2434898 - Office 2007 registry fixes. Does not apply.
    http://support.microsoft.com/kb/2413659 - Office 2010 problem. This exact issue. Says 'No microsoft products that match this hotfix are installed'
    Work Around:
    I can saving new versions of these files overrides this issue, but this is sometimes not possible for end-users who only have specific access to ONE SPECIFIC FILE in a particular network share.
    Please let me know how I can alleviate this issue!
    Thanks
    -Chris

    Hi,
    Are those problematic documents created via previous versions of Office?
    Please also try to run a repair of your Office 2013 installtion and check if it helps. See:
    http://office.microsoft.com/en-in/excel-help/repair-office-programs-HA010357402.aspx
    Regards,
    Steve Fan
    TechNet Community Support

  • System freeze after resume from suspend to RAM

    Hi,
    since quite a while (probably ever) I am unable to suspend my computer to RAM because everytime it freezes a few seconds after resuming, never to become alive again until a reboot. After some investigation, I managed to get kernel logs by taking a picture of my screen. The logs were not written to disk, hence I didn't see anything before. I had to write these by hand, I hope I didn't insert any mistakes:
    kernel: sas: Enter sas_scsi_recover_host busy: 2 failed: 2
    kernel: sas: trying to find task 0xfff880008b5b680
    kernel: sas: sas_scsi_find_task: aborting task 0xfff880008b5b680
    kernel: sas: sas_scsi_find_task: task 0xfff880008b5b680 is aborted
    kernel: sas: sas_eh_handle_sas_errors: task 0xfff880008b5b680 is aborted
    kernel: sas: trying to find task 0xffff8804606ccb40
    kernel: sas: sas_scsi_find_task: aborting task 0xffff8804606ccb40
    kernel: sas: sas_scsi_find_task: task 0xffff8804606ccb40 is aborted
    kernel: sas: sas_eh_handle_sas_errors: task 0xffff8804606ccb40 is aborted
    kernel: sas: ata7: end_device-0:0: cmd error handler
    kernel: sas: ata8: end_device-0:1: cmd error handler
    kernel: sas: ata7: end_device-0:0: dev error handler
    kernel: ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
    kernel: ata7.00: failed command: READ VERIFY SECTOR(S)
    kernel: ata7.00: cmd 40/00:01:00:00:00/00:00:00:00:00/e0 tag 11
    res 40/00:48:a0:79:88/00:00:07:00:00/40 Emask 0x4 (timeout)
    kernel: ata7.00: status { DRDY }
    kernel: ata7: hard resetting link
    kernel: sas: ata8: end_device-0:1: dev error handler
    kernel: ata8.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
    kernel: ata8.00: failed command: READ VERIFY SECTOR(S)
    kernel: ata8.00: cmd 40/00:01:00:00:00/00:00:00:00:00/e0 tag 11
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    kernel: ata8.00: status { DRDY }
    kernel: ata8: hard resetting link
    This issue seems to be related to disk failures like bad sectors but I am quite sure, that my SSDs are in a good shape. I ran some SMART tests, they all turned out to be okay. Suspending from my dual-booted Windows works fine as well (although if the bad sector would be on the linux partition, it would probably not affect Windows).
    Here's my setup:
    $ lsblk -St
    NAME HCTL TYPE VENDOR MODEL REV TRAN NAME ALIGNMENT MIN-IO OPT-IO PHY-SEC LOG-SEC ROTA SCHED RQ-SIZE RA WSAME
    sda 1:0:0:0 disk ATA Corsair Force 3 2 sata sda 0 512 0 512 512 0 cfq 128 128 0B
    sdb 7:0:0:0 disk ST1000DM 003-9YN162 NDP3 usb sdb 0 512 0 512 512 1 cfq 128 128 0B
    sdc 0:0:0:0 disk ATA OCZ-REVODRIVE3 2.25 sas sdc 0 512 0 512 512 0 cfq 128 128 0B
    sdd 0:0:1:0 disk ATA OCZ-REVODRIVE3 2.25 sas sdd 0 512 0 512 512 0 cfq 128 128 0B
    sr0 2:0:0:0 rom TSSTcorp CDDVDW SH-222AL SB00 sata sr0 0 512 0 512 512 1 cfq 128 128 0B
    $ lsblk -f
    NAME FSTYPE LABEL UUID MOUNTPOINT
    sda
    ├─sda1 ntfs Recovery 567437B974379B27
    ├─sda2 vfat DC2D-099E /boot
    ├─sda3
    ├─sda4 ntfs FEBED982BED933BD
    ├─sda5 ext4 arch 41bad924-84a2-4e0a-9cd4-4ea723a2a5a3 /
    └─sda6 swap 793fb3c1-8bec-4023-a7c3-ee94eee2e67a [SWAP]
    sdb
    └─sdb1 ntfs HDDRIVE2GO 2212E50812E4E231
    sdc
    └─sdc1 linux_raid_member home:0 208937dc-2904-e71c-435a-9928671e07a3
    └─md0 ext4 revodrive ffe9d38f-87f2-44e1-ae26-f36c910af3c5 /home
    sdd
    └─sdd1 linux_raid_member home:0 208937dc-2904-e71c-435a-9928671e07a3
    └─md0 ext4 revodrive ffe9d38f-87f2-44e1-ae26-f36c910af3c5 /home
    I am not sure which one of the disks causes the freeze but I assume it's the revodrive because the logs talk about two drives. The Revodrive internally holds two drives, which are set up to operate in a RAID 0. Windows is installed on the Corsair drive, and has no access to the Revodrive. However, I used to run Windows on the Revodrive a few years ago, and it worked just fine.
    Another interesting thing is that when I try to test suspend to RAM, the system does not freeze, nor produce errors. This only happens if none is written to /sys/power/pm_test (which means no automated wake-up, no testing).
    Any ideas on how I could narrow down this issue? Thanks a lot!
    EDIT
    I just checked and confirmed that this issue is originating from the OCZ Revodrive:
    $ dmesg | grep ata7.00 | head
    [ 7.136432] ata7.00: ATA-8: OCZ-REVODRIVE3, 2.25, max UDMA/133
    [ 7.136436] ata7.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32)
    [ 7.146442] ata7.00: configured for UDMA/133
    $ dmesg | grep ata8.00 | head
    [ 7.310018] ata8.00: ATA-8: OCZ-REVODRIVE3, 2.25, max UDMA/133
    [ 7.310023] ata8.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32)
    [ 7.320022] ata8.00: configured for UDMA/133
    Last edited by tuttiarch (2015-01-31 15:54:29)

    Thank you for the link, unfortunally I don't have a NVIDIA card but use the Intel IGP (HD4600, Haswell) - maybe I should have mentioned that...
    And other than in this bug report I cannot kill X or anything because neither other TTYs work - I cannot input anything (although the hotkeys work weird enough) nor is SSHD running because the system is completely frozen...
    Very funny thing is that for the last 2 days my system didnt freeze once (suspended about 6-7 times during one boot), even though for the 2 weeks prior to that, it froze EVERY SINGLE TIME I resumed from suspend, it didnt work once...

Maybe you are looking for

  • "Where from:" Information don't work for any file type

    As i know Safari and iChat stores the download url from a file - downloaded over the internet - in a meta tag called 'kmditemwherefroms'. You can see this information in the finder information dialog. But not on my system. I'm running 10.4.8 on power

  • File adapter with modules

    Hi all Why is the File adapter does not work properly with modules. The source file does not be picked up from the source directory when I use module with the CC , but when I remove the modules it works fine. Do I have to activate anything or to do a

  • Propagate the WebCenter identity to the Portlet context

    Hi all, How can I propagate the WebCenter identity to the Portlet context? PortletAdfContext.getCurrent().getSecurityContext().getSubject() = 'anonymous' but I am logged with my user. Thanks.

  • CCM 2.0 Training material

    Hello All, I am preparing for SRM 5.0 certification and if any one has CCM 2.0 training material  that would be of great help. Also any certification questions/tips for SRM 5.0 also be of great help. Thanks, Raj

  • SQL server is Running Very Slow

    hi, I used this following query for finding out how many connection are connected, it is showing that 70 connections,my ram is 16GB,  but still my sql server is running very slow. how can i increase my sql server speed. or how can i analyses that.I c