Adding 400 port to Mac pro quad

what is best card to add a 400 port to Mac Pro? XHA1 will not work via any 800 cable, must plug directly into 400 port. Why was the 400 port dropped anyway?

There are adapters, such as
<http://www.sonnettech.com/product/fw_adapter.html>
cables
<http://www.radtech.us/products/ProCableFW400800.aspx>
and PCIe boards
<http://www.sonnettech.com/product/allegrofw400pcie.html>

Similar Messages

Adding USB ports to mac pro

Hi,
i was wondering if anyone knows if it's possible to fit more usb ports in the back of the Mac Pro?
I got my mac pro about 4/5 years ago, and could really use some more ports.
Thanks for any help and advice,
Tom

Linc Davis wrote:
What's wrong with using a hub?
A few things:
With a hub, all devices must share the bandwidth of the one built-in port the hub is on. If one device on the hub takes up all the port bandwidth, too bad for the others. Or they will fight it out. But with most types of USB cards, each individual port on the card gets full USB bandwidth...no conflicts.
You need to use up a built-in USB port to plug in a hub, so adding a 4-port hub only gives you 3 more new ports in reality. With a USB card, all card ports are in addition to the Mac Pro ports.
A hub needs to take up one more outlet on your power strip. Or two or three outlets if it has a big transfomer. A USB card uses the Mac Pro power supply directly with no additional messy power and data cables.
A hub probably doesn't cost that much less than a USB card, if there is any price difference at all, yet the card has so many more advantages.
About the only reason to not get a USB card is that you've already used up the slots in your Mac Pro.

Adding new hard drive to Mac Pro (quad core)

I've just ordered a new Mac Pro quad core (2.66 GHz) with one GB HD. Since Apple is charging £240 for a second drive I decided to get it from somewhere else. I found a 1GB Western Digital Caviar Green but I also noticed 1GB WD Caviar Black. I wonder if anybody has any experience of those drives and would they work with the latest Mac Pro ?
Does anybody knows what make of drive is Apple using in their latest Mac Pros ?
Tom

*WD Caviar Black 640GB*
HD Tune: WDC WD6401AALS-00L3B2 Benchmark
Transfer Rate Minimum : 59.1 MB/sec
Transfer Rate Maximum : 118.1 MB/sec
Transfer Rate Average : 96.4 MB/sec
Access Time : 11.8 ms
Burst Rate : 125.3 MB/sec
*Black Caviar 1TB:*
HD Tune: WDC WD1001FALS-00J7B Benchmark
Transfer Rate Minimum : 53.9 MB/sec
Transfer Rate Maximum : 108.7 MB/sec
Transfer Rate Average : 86.1 MB/sec
Access Time : 12.9 ms
Burst Rate : 111.5 MB/sec
+(note the slower average to the smaller 640GB model)+
*Green Power 1TB*
HD Tune: WDC WD10EADS-00L5B1 Benchmark
12-23-2008
Transfer Rate Minimum : 41.6 MB/sec
Transfer Rate Maximum : 95.6 MB/sec
Transfer Rate Average : 74.3 MB/sec
Access Time : 14.0 ms
Burst Rate : 117.2 MB/sec
*WD Caviar Blue 640GB*
HD Tune: WDC WD6400AAKS-00A7B Benchmark
Transfer Rate Minimum : 55.6 MB/sec
Transfer Rate Maximum : 113.3 MB/sec
Transfer Rate Average : 90.2 MB/sec
Access Time : 11.8 ms
Burst Rate : 112.9 MB/sec
the 32MB cache did not make a real or noticeable difference in benchmarks
http://www.barefeats.com/hard112.html

UPGRADING AND MIXING MEMORY ON MY MAC PRO QUAD CORE DUAL 2.8 (Xeon)?

Hello,
I have a Mac Pro Quad Core Dual 2.8GHz (Xeons) with 4GB of memory (2 x 1GB Apple modules + 2 x 1GB other brand - Shown as "Manufacturer 0x855D") and now I want to fill the other 4 memory slots by adding an additional 16GB (4 x 4GB modules) for a total of 20GB of RAM.
My 2 questions are:
1.- In which order/pattern should I install these new 4 X 4GB modules along with my original Apple 2 x 1GB modules and the "Manufacturer 0x855D" 2 x 1GB modules the best way (for better performance)? - I have heard stories that if I do it improperly, I could slow down my Mac Pro...
This is how I have them configured right now:
Raiser A / DIMM 1 = 1GB (Manufaturer "0x830B") - I assume this is the Apple memory, right?
Raiser A / DIMM 2 = 1GB (Manufaturer "0x830B")
Raiser A / DIMM 3 = Empty
Raiser A / DIMM 4 = Empty
Raiser B / DIMM 1 = 1GB (Manufacturer "0x855D") - How can I find which manufacturer is this?
Raiser B / DIMM 2 = 1GB (Manufacturer "0x855D")
Raiser B / DIMM 3 = Empty
Raiser B / DIMM 4 = Empty
2.- What brand would be most compatible to work with my Apple 2GB (2 x 1GB) factory memory? Kingston? Crucial? Mushkin? iRam? Corsair? OWC? (Does OWC sell their own brand? or which one do they carry?-its not specified on their web)
Thank you so much in advance for all your help!

About RAM installation in the Mac Pro
Mac Pro memory arrangement photos
Mac Pro Memory Configuration
Memory Tests- "2008" Mac Pro
Ram should be installed minimally in matched pairs and optimally in matched quads. This means the memory modules are the same size and specifications. They should also be equipped with the Apple-certified style of heat sink.
Brand really doesn't mean much as long as they work.

Mac Pro Quad core Intel Xeon upgrade advice please!

Hi all, i have a Mac Pro Quad core 2 x 2.8ghz Intel Xeon (2008 model) with 4gb RAM.
I am planning on giving it some upgrades and a fresh OS install as it is slowly grinding to a halt (particualrly noisey hard drives)
Can anyone recommend best/fastest/silent! S-ATA hard drive to upgrade to?
Can anyone recommend a good replacement ATAPI DL DVD-RW Drive as mine is also on its way out.
Ram upgrade. Lots of space for RAM so what would you all recommend?
Ultimately i am finding myself working with alot of large PS file and so would welcome any suggestions to improve/soup-up the processor/performance.
Thanks for any advice in advance...

24GB RAM gets cost ly when you look at 800MHz FBDIMMs in 2x4GB
You shoudl have added more as 4GB is vary basic and miinimal
Any SATA drive device is fine. WD Black 1-2-4TB / WD 10K VRs are fast but not as quiet though I do hear those WD Blacks.
A single SSD for a system is nice.
10.6.8 works best in that system.
Your GPU most probably is in need of an upgrade.
You should never need to do a reinstall of the OS. Clone. Yes. And start wit h a new OS by not upgrade in place over the old OS but that is when to clean install, clone and use Set up Assis tant.

Boot Camp, Vista Ultimate x64 SP1, 2009 Mac Pro Quad 2.93, ATI 4870 HD

Hello All,
I’ve run into a problem installing Boot Camp with Vista Ultimate x64 SP1 on my early 2009 Mac Pro Quad 2.93 with Apple’s ATI Radeon 4870 HD (the one with one DVI and one mini-display). I followed the instructions from the Boot Camp Installation and Setup Guide, and everything was going great until I hit page 12 of the Guide (Step 3). The Boot Camp drivers installed without error, and prompted me to reboot. Upon rebooting onto the newly installed Vista x64 partition, the screen went black after the chkdsk screen appeared. I can boot into Vista safe mode, but booting into Vista normally results in the black screen. On a hunch, while in safe mode, I uninstalled the ATI video drivers installed by Boot Camp. I was then able to boot Vista normally, but only with the standard VGA adapter. Then I tried installing the latest 9.4 ATI drivers from the chipset vendor, AMD, http://game.amd.com/us-en/drivers_catalyst.aspx. Booting normally after the ATI chipset drivers were installed left me with a mostly black screen, and a few swizzles of horizontal color, but not enough to make out any sort of image. Once again, I was able to boot normally by first booting into safe mode and then uninstalling the ATI driver, leaving me with the standard VGA driver.
The displays I have tried so far are 1) Apple Cinema HD 23”, and 2) Apple Cinema 20”. Also, I have tried all 6 permutations with the ports on the Apple version of the ATI Radeon 4870 HD with both displays (using the mini-display to DVI adapter), 2 permutations with both displays, and 4 permutations with single displays. All permutations result in the same black screen after installing Boot Camp drivers.
Am I missing something? It seems to me that there is a display driver that needs to come from Apple that will work with the Apple version of the ATI Radeon 4870 HD in Vista Ultimate x64 SP1 attached to an Apple display. I’ve installed Vista Ultimate x64 SP1 and many other operating systems in the past 27 years of working with computers, and typically with video cards I’ve had to get the drivers from the vendor that shipped the card, not the chipset vendor. Sure, occasionally the opposite is true, and I don’t mind spending a few days to figure out what works best for me as long as I believe I am making progress.
Has anyone else run into this problem with his or her early 2009 Mac Pro Quad 2.93 with Apple’s ATI Radeon 4870 HD? I’m posting this in the Boot Camp forum as I think this problem is rooted in the Boot Camp drivers, specifically for the Apple ATI Radeon 4870 HD. Please let me know if I should post elsewhere.

You are the second person I think I've seen with trouble using Mac Pro and ATI drivers (other was on Mac Pro forum).
When updating graphics, there are extra steps that insure you get the best working drivers.
I've always found Apple to be behind the curve on Windows support. Drivers that come with a card from the vendor ususally means ATI or Nvidia, and even then, you go to the web and download and install the latest tested / beta / qualified drivers. Some people try a variety of driver versions to find the one that works best.
Apple has not been updating Boot Camp drivers for Late 2008 and on Macs. Boot Camp 2.1 is now over a year old. What is on your OEM Leopard DVD is the only drivers I would use - if at all! try without is what some do, and then see if you can selectively install. Under Windows 7, I don't need or install, and now with the RC/7077 version of 7, Microsoft 'blocks' installing Apple Boot Camp drivers as known to cause problems.
If it ain't broke, don't fix it. Unistall the various Apple services, drivers, startup items that you can live without or until you narrow it down. iTunes 8.1+ in Windows can break and prevent ability to even use optical drives and devices for instance.
Some tips for upgrading drivers, one from eVGA forum but should translate.
http://www.evga.com/forums/tm.asp?m=396474
http://game.amd.com/us-en/drivers_catalyst.aspx
http://downloads.guru3d.com/download.php?det=1655

Will my Cinema HD Display work with a new Mac Pro Quad Core?

Will my Cinema HD Display work with a new Mac Pro Quad Core?

Yes.
Thunderbolt ports and displays: Frequently asked questions (FAQ)
https://support.apple.com/kb/HT5219
https://www.apple.com/thunderbolt/
http://support.apple.com/kb/HT5299

Firewire port on Mac Pro

If I use an adapter to connect firewire 400 to 800 port on Mac Pro. Will entire firewire bus on Mac Pro reduce to 400 speed or each port is independent?

All ports feed into the same bus, but you can run a 400 device from one port and an 800 device on another port and both will operate to their respective theoretical speeds. However, if you daisy-chain FW800 devices into a FW400 device and then to the Mac Pro, all will operate at 400 speeds.
Matt

Hi...m using a mac pro quad core.....its not booting up...i can only see the apple logo and a circle loading...could not get into the login screen

hi...m using a mac pro quad core.....its not booting up...i can only see the apple logo and a circle loading...could not get into the login screen...any suggestions please.....m in the middle of a project and now i have got this one
regards,
v.s.bharan

Welcome to Apple Discussions!
Do you keep your data backed up?
If not, you should always do so*:
http://www.macmaps.com/backup.html
You never know when a hard drive or a directory might go bad. Having a bootable clone is a must.
That link also shows you some tools you can use to recover data.
If you aren't backed up, try buying those tools first, before attempting to repair the directory.
Directory issues can be fixed with these tools*:
http://www.macmaps.com/directoryfaq.html

Error message on my Mac Pro Quad Core Dual

Hello..I'm hoping someone out there can help or advise me.
I turned on my mac this morning to find it's normal loading screen of grey with the darker grey logo in centre..all normal at this stage. This was followed by a wipe from top to bottom making the background grey a little darker and in the centre the apple logo was replaced by what appeared to be a semi transparent power button symbol with the words. "You need to restart your computer. Hold down the Power button for several seconds or press the restart button"
I have tried this several times to no avail I have also zapped the P RAM again nothing. Can anyone out there help. I have a Mac Pro Quad Core Dual which is only a few months old and is up to date with its system software.
I could be so grateful of any assistance.
Warm regards
Sophia

Make an appointment. But in the meantime...
So from cold boot, you can't do the Command Option P R through 2-3 full reboot cycles (don't let up)?
Unplug everything and let it sit overnight without power cord or anything. That is the only way to rest the SMC system management controller on the 2008 model, the older model still had a reset button.
Also learned that the 2008 Macs can all boot AHT if the original OEM installer was used to install the system and the drive has not be completely reformatted and retail OS X used, just holding down "D" on startup. But you have to
Also, pull all your hard drives. Rule out that, which I have seen a hard drive cause panic on startup, which required disabling journaling and other repairs from Disk Utility and deleting caches, then repair, and finally do Safe Boot (shift key down on startup).
The only way to test RAM is with TechTool Deluxe or Pro; with Memtest or Rember; and to test some devices is to try using a differnent one, keyboard and mouse included if you have any.
Last hope: open case, look inside, take the two RAM Riser cards and pull out, check the DIMMs are fully seated.
If you have 3rd party memory, remove that (would need to before taking in probably).
Might want to put RAM back to way it shipped with 2 x 1GB and one DIMM on each Riser in slot one. Maybe that will wake this sleeping giant. Changing RAM config use to be one way to clear nvram in the distant past in the time of Arthur.
PS: it is "odd" to find a BTO 3.2GHz system, and only 2GB. For memory performance, Barefeats found a marked improvement with 8 DIMMs, and of course Mac Pro really needs memory to feed 8 cores and pro apps (2GB would be okay for web and email type use only).

Windows – but Which? (What to install on Mac Pro Quad Core?)

First, apologies in advance if this seems like repetition of a recent topic, but I read through the recent "Vista vs XP" thread and it didn't quite answer my questions.
Basically, I'm planning on buying a Mac Pro "Quad Core" 2.8 and installing Boot Camp and a Windows OS startup. This puts me into the notoriously tricky area of picking the right version of Windows for my needs, something I haven't really had to deal with in regards to OS X.
Basically, I'm not looking for something with too many bells and whistles or to much bloatware built into the OS. Also, I'll probably be using some older software/shareware, so backwards compatibility is an issue. On the other hand, I'd like something that works with the Quad Core architecture at its greatest efficiency.
This means I'm wondering about a couple of features that I may or may not need, and it would be of great help if you folks could point me in the right direction regarding these:
x64 – Since the Xeon processors in the Mac Pro are 64-bit processors, am I better off with "x64"-compatible versions of Windows (either Windows Vista or x64 versions of XP)? Will this cause problems starting up older programs that may not have been written for x64?
*Dual Processor Support* – the Quad Core, of course, is a dual processor – will I get better performance from a version of Windows that list "Dual Processor Support" among its features (basically, the "pro", "business", or "ultimate" versions of XP and Vista)?
If I need those features, I'm probably looking at getting either the x64 version of Windows XP Pro or the Business or Ultimate versions of Vista. However, I'm leaning against Vista based on backwards-compatibility and bloatware issues. That leaves XP Pro x64, but I might go for a more basic version of XP if I find out the x64 or DPS features aren't actually something I need. (The other "extras" in XP Pro don't sound like anything I need.)
Also, I'm likely to install Parallel Desktop at some point and don't want a version of Windows that would have compatibility problems there, either.
Anyway, any answers you folks can provide for me in this regard would be very helpful.
Thanks in advance,
Peter

Truth is, I am disappointed in VMware Fusions slow walk toward full support for 64-bit and SP1 but 2.0 beta is getting there. Never used Parallels but best to check their own support forums. They also updated the 1.x version recently.
http://communities.vmware.com/community/beta/fusion
http://forums.parallels.com/
You don't need anything first, except I would start with a new hard drive for Vista, don't even do anything with it and pull OS X drive, boot Vista DVD and go from there, just as you would normally. Much easier. After it is installed is when you need Apple BootCamp from your Leopard OEM DVD, install, and then Apple Software Update will take care of 2.1. And install your graphic drivers yourself.
The problem(s) come with trying to use BootCamp Assist and setting up partitioning, and it only makes it harder - not easier - on Mac Pro (you aren't and don't want to use your OS X boot drive).
Windows on Mac forum @ MacRumors
http://forums.macrumors.com/forumdisplay.php?f=86
And their Mac Pro area http://forums.macrumors.com which has a lot of Vista talk from Mac Pro owners.
The only real issues are which graphics card to get today or in next weeks, what drives you are going with and other upgrades like memory (8 x 1GB is actually a good base ideal figure so all DIMM slots are taken up).
Barefeats has a number of benchmark articles:
Radeon 3870: http://www.hardmac.com/news/2008-06-16/#8451
Vista graphics: http://www.barefeats.com/harper11.html
Memory: http://www.barefeats.com/harper12.html
Drives: http://www.barefeats.com/harper9.html
WD 300GB Raptor: http://www.barefeats.com/hard103.html
- this is the drive to die for, but not natively supported
I buy most of the upgrades I need over the last ten years from OWC http://www.MacSales.com that specializes in Mac.
http://eshop.macsales.com/shop/memory/Mac-Pro-Memory
http://eshop.macsales.com/item/Western%20Digital/WD6400AAKS/
- until the WD "Black" series (I guess Blackbird name or SR71 are already taken) along with 3rd generation of their RE series drives. WD has been popular, reliable, with Mac Pro for last two years. Can't say the same of every vendor. Samsung F1 is also a real winner.
If you buy only one book to understand and get the most out of OS X: "Mac OS X: The Missing Manual" (Pogue has a Missing Manual Series on most everything, and this is the most popular recommended for Mac OS).
http://books.slashdot.org/books/08/02/27/1551206.shtml
I needed 3-4 for Vista before I found "Administrator's Pocket Consultant" and O'Reilly's "Vista Annoyances" are both excellent along with MS Press's "Inside Out."

I have a WD 2 tb hard drive that I want to use to back up my Mac Pro quad core. How do I create a back up startup disk? Also, when I used Time macine, it only backed up users and not the system or library folders. Ideas?

I have a WD 2 tb hard drive that I want to use to back up my Mac Pro quad core. How do I create a back up startup disk? Also, when I used Time macine, it only backed up users and not the system or library folders. Ideas?

Welcome to Apple Support Communities
Time Machine should be enough to make a backup of your files. Also, it should back up all folders, so open System Preferences > Time Machine > Options, and make sure that there are no folders included in the excluded items list.
If you want to create a bootable clone of your hard drive, you need to use an app like Carbon Copy Cloner or the Disk Utility's Restore feature > http://pondini.org/OSX/DU7.html

Are these Seagate 2TB drives compatible in my Mac Pro Quad Core 2.66 GHz?

I still have an Apple Mac Pro "Quad Core" 2.66 that was introduced August 7, 2006. I currently have 4 of the following Seagate internal hard drives installed: ST3750640AS SEAGATE BARRACUDA 7200.10 - HARD DRIVE - 750 GB - INTERNAL - 3.5" - SATA-300 - 7200 RPM - BUFFER: 16 MB
I want to know if these hard drives will work in this computer: Seagate Barracuda XT ST32000641AS 2TB 7200 RPM 64MB Cache SATA 6.0Gb/s 3.5" Internal Hard Drive -Bare Drive.This computer is powered by two 2.66 GHz dual core Intel Xeon 5150 processors.
The old drives were purchased from NewEgg and I want to purchase the new ones from there also. Are these 2TB drives compatible in my computer?
Thanks,
Lou Hosta

SATA is SATA.
Apple introduced GPT (GUID) years ago to support 2TB and larger (default partition scheme).
SATA III is also backward compatible with SATA II (otherwise, who would Seagate have to sell to?)
The only issues have been with green drives, using green version for RAID or for performance purposes.

Fileshare between my Mac Pro Quad Core Intel Xeon (64-bit) & Power Mac 9600

I want to make my Power Macintosh 9600/233 (Mac OS 9) a shared computer with my Mac Pro Quad Core Intel Xeon (64-bit)(Mac OS 10.6.6). I am using a Netopia Model 3346N-VGx DSL Ethernet Managed Switch to network with my Samsung printer and the Mac Book Pro.
I also have a Power PC G4 (Mac OS 10.5.8) connected (via a Ziplinq 48" Retractable Crossover Network Cable) to a Farallon EtherWave 10 Base-T AAUI Transceiver, which in turn is connected to the Netopia, from which I can share files. All of this is ethernet connectivity.
I thought I could connect my 9600 using the same method as for the G4 or by connecting the ethernet cable from the 9600 directly into the Mac Pro Quad Core. However, neither of these methods work.
An additional stumbling block is that I have not used this 9600 for several years and am not sure of its account name. I'm fairly certain of its password. But because I don't have a second monitor for this machine, I can't muddle my way in.
My questions:
1. What might be a network solution to this dilemma?
2. Or, do I need to get another monitor for this computer and leave it un-networked and just transfer files manually?
3. Or, would whatever hard drives are in the 9600 be transferable into the networked G4 or the main Mac Pro? (not sure what they are.)
Any suggestions greatly appreciated.

Oh man, what a dilemma...
1. What might be a network solution to this dilemma?
Without a monitor on the 9600, almost none. At the very least you'll need to configure the server with appropriate network settings for your environment, and that can't be done headless.
You might only need a display for long enough to setup the network, but you'll need one all the same.
Once the network is configured your options are either AFP or FTP, but I'm not even sure the old version of AFP is supported anymore, which means you may need to fire up an FTP client on the 9600 and push the files to your MacPro.
2. Or, do I need to get another monitor for this computer and leave it un-networked and just transfer files manually?
As mentioned above, you're going to need a monitor at the very least to configure the network settings. I'd be inclined to say at that point you might as well copy the files off any way you can and put the 9600 to rest. If you're really, really fortunate and the 9600 has a CD burner I'd probably use that and count myself lucky
3. Or, would whatever hard drives are in the 9600 be transferable into the networked G4 or the main Mac Pro? (not sure what they are.)
The 9600 shipped with SCSI drives, which no current Mac support (at least without a SCSI card), so there's no way to remove the drive from the 9600 and attach it directly to the MacPro.

I have mac pro quad can i upgrade from leopard to lion on one of the hardrives and then drag all my protools sessions into from the leopard hardrive to the lion hardrive thanks

i run a commercial recording studio since 2009 and purchased a mac pro quad core with os x 10.5.8 and record with protools, it has now got to the point where i can no longer purchase plugins for protools because the operating system is to old i need at least snow leopard ,i have never upgraded and am concerned about losing any previous protools sessions and plugins ,it has been suggested to me to upgrade just one of the hardrives to snow leopard or lion or the latest system and then just open a protools session on the old osx hardrive and save to the new upgraded hardrive , is this possible? or has anyone any suggestions ,many thanks

You should seriously consider establishing a Boot drive, with only System, Library, Applications, and the hidden unix files (including Paging/Swap) on it. User files are moved off to another drive.
This makes maintaining the System and maintaining your User files much easier, and it makes your Mac faster in every way.
How to Move the Home Folder in OS X - and Why - Chris Pirillo
Japamac's Blog: Make Space for Performance-- Moving the Home Folder

Adding 400 port to Mac pro quad

Similar Messages

Maybe you are looking for