Advantages and Disadvantages of Dual booting Windows on PXI Device

Hello,
In solving my previous problem of running a DLL in RTOS I've stumbled upon another solution. But i wanted to know the pros and cons of this before i make the leap.
I want to install windows on the PXI device so that the NHR DLL files are run inherently on the windows kernel and i have access over my DAQ devices without placing them in the remote target.
What are the advantages and disadvantages of installing a windows only on the DAQ device and running all my operation from it. Do i loose my real time features? I dont know, I'm really new to LabView and may sound really dumb. Please excuse my lack of knowledge.
With Regards,
Khalid.

Hello Bob,
Thank you for your insightful answer. I also thought this might happen, loosing all the RT features.
I have another question for you. If i use a RT variant of windows like "Windows Embedded 8", will this make any difference? Can i regain my RT features by it or i have to go with the LabView RTOS.
I'm pushing towards a windows system because i have to run this DLL file from NHR which is not supported by the LabView RTOS.
Moreover, I could just install just windows onto the PXI controller. I'm not being able to make it dual boot. Can you guide me towards proper guideline to do so? I looked at the knowledge base file about dual booting, but the instructions dont exactly match with my available options in BIOS setup.
Any suggestions from anyone is much appreciated.
With Regards,
Khalid.

Similar Messages

Y500 dual boot windows 8 and fedora 19 problem

I bought a y500 two days ago and i wanted to dual boot windows 8 and fedora 19, so here's what i did
1. downloaded fedora 19 (x64) iso from the fedora website.
2.made a live USB using live usb creator.
4.opened disk management utility and shrunk the c drive (windows 8 was installed here) by 100 gb and kept the 100gb unallocated.
3. started the laptop with novo button, changed the bios config to boot from usb.
4.installed fedora from usb, selecting the 100gb unallocated memory for installation
5.restarted the laptop.
now the problem is fedora works perfectly but when i try to boot windows 8, the following error is shown.
windows failed to start
file:\BOOT\BCD
status: 0xc0000225
info:the boot configuration data for your PC is missing or contains errors.
i am guessing the fedora installation overwrote the boot files of windows and
i have not taken a backup. please help

hi,
I have a Y500 and I wanted to dualboot fedora 19 with windows 8, this proved to be unsuccessful. I had made a repair disk before the process (but not a set of recovery disks unfortunately >.< ). now I inserted the repair disk and selected the automatic repair option, it showed a message that auto recovery has failed. now when I pressed the NOVO button and selected the system recovery option, it does not go into the OKR menu but continues with the normal booting process. Can somebody guide me or give links where I can find step by step instructions to making OKR work and reset my laptop to factory settings? PLEASE help As Soon As Possible
NOTE: I did resize the windows 8 os partition but the recovery and the lenovo partition are still untouched

Dual Boot Windows 8 and Linux?

I have (UEFI System) an ASUS K55A UEFI motherboard laptop that came factory with Windows 8. I would like to install backtrack linux and Windows 8, but before I go screwing up my laptop, I want to see if this would be at all possible. I would use a virtual
machine, but I need Backtrack Linux on a physical machine for testing purposes as I am taking a course in computer forensics, and I want to test cracking my home wi-fi. My processor is an Intel Core i5 2.5 ghz with a 500 GB HDD and 8GB DDR3 RAM. Any insight
on this would be appreciated. Thank You.

Hi,
You can refer to this article to get detail information.
http://apcmag.com/how-to-dual-boot-windows-8-and-linux.htm
Niki Han
TechNet Community Support

[SOLVED] Dual boot windows 7 and arch Linux with seperate hard drives

Ok so I'm stuck trying to get my computer to dual boot windows 7 and arch. They are installed on different hard drives and I have grub 2 as the boot loader. I can't find any tutorials on how to do it with seperate hard drives I know how to do it if they are on the same hard drive. Also I want windows on the "first" hard drive how do I check to see which one it considers the first?
Last edited by bdawg (2012-09-21 23:15:37)

DSpider wrote:
drobole wrote:If you want to change it so that sda becomes sdb and sdb becomes sda, you should be able to do that in BIOS.
Not from the BIOS. He would need to physically open up the computer and switch the cables between them (or add another drive).
There's no actual performance increase in changing this order. Performance increase is when you have the partitions as close to the beginning of a HDD as possible, where the platters spin faster (basic mechanics, not to be confused with CD/DVD, which are being written from the inside-out to prevent errors after extended usage), and it especially doesn't apply to SSDs whatsoever.
You may be right about that. I remember I had to do this a while back but I probably switched the cables. It also messed up the drive mapping in Windows 98 if I remember correctly.

Dual booting Windows 8 and Arch Linux with UEFI

Hi all!
I'm trying to install Arch Linux on my computer where I already have Windows 8, and I'm getting a little stuck when it comes to the partitioning.
Following the beginner's guide and the method here: https://wiki.archlinux.org/index.php/Un … n_in_Linux for setting up the partitions properly, regarding UEFI. My problem is that when using cgdisk to set up a new EFI system partition (ef00), I get an error message when trying to write the partition table (just saying that something went wrong). I figure the problem is that I already have a partition like this (correct me if I'm wrong), but it really looks like it succeded (see info below). So my question is: How do I preceed to keep my Windows 8 installation happy, but installing Arch? Do I remove the old EFI system partition and create a new one, or is there some method that allows me to edit the already existing one, to allow me to dual boot Windows 8 and Arch?
My partition table now looks like this:
Part. # Size Partition Type Partition Name
1007KB free space
1 500MB Windows RE Basic data partition
2 300MB EFI System EFI system partition (this one was already present on my system)
3 128MB Microsoft reserved Microsoft reserved partition
4 63.5GB Microsoft basic data Basic data partition
8 512MB EFI System EFI System partition (this is the one I tried to create when I got the error message)
5 29.5GB Linux filesystem Arch (this is where I was going to put my Arch installation)
6 22GB Windows RE Basic data partition
7 1024MB Windows RE Basic data partition
615KB free space
Just for the record; I only created partition #8 and #5.
Any help is appreciated! And sorry for beeing a total noob, but I really suck at this.

sudo make sandwich wrote:If it is possible to share ESP between OSes, how do I do this (would it be sufficent to follow this section: https://wiki.archlinux.org/index.php/Beginners'_Guide#For_UEFI_motherboards)?
There's really very little to do to share an ESP between OSes. Most OS installers will auto-detect the ESP and use it. Problem solved. For Arch it may be a bit more effort just because Arch uses a more hands-on installation process, but I've only done a couple of Arch installations, and the last one was several months ago, so I don't recall the details clearly enough to comment.
And how big will the partition need to be? The beginner's guide says 512MB or higher.
I don't know what was in the mind of the author, but my guess is that's because that's roughly the cutoff point where mkdosfs starts creating FAT32 by default rather than FAT16. The ESP is officially supposed to be FAT32, not FAT16, although FAT16 usually works OK. It's also possible to create FAT32 on smaller partitions by using an explicit option to mkdosfs ("-F 32").
The optimal size of the ESP depends on the files stored on it. If you don't store your Linux kernels, something as small as 100MiB is usually adequate; but a few Linux kernels and their initrd files can consume twice that amount. My own recommendation is for the ESP to be 200-500MiB.
The only error message I got from cgdisk is "Problem saving data! Your partition table may be damaged!", however booting Windows again works fine. Parted did not complain about antything.
Use the "verify" function in cgdisk. That will reveal any problems with the data structures. If a verify turns up OK, then that means that cgdisk ran into some sort of disk problem. Running gdisk rather than cgdisk and using the gdisk "w" option (without making any changes) may produce a more helpful error message.

Dual boot Windows 7 and Arch from 2 seperate drives (UEFI)

Hello everyone, I've been working on installing Arch to a secondary hard drive for the past few hours, but I am trying to make sure I won't mess up my Windows 7 install. I have found several topics talking about dual booting Windows 7 and Arch, but not a whole lot on booting them from separate drives. My drives are currently setup as follows.
sda (120GB SSD for Windows 7)
sda1 (100MB System Reserved NTFS partition)
sda2 (Windows 7 install)
sdb (1TB HDD for Windows programs, files, etc)
sdb1 (1TB NTFS partition)
sdc (1TB HDD)
sdc1 (boot 512MB FAT32)
sdc2 (root 500MB ext4)
sdc3 (home 300GB ext4)
sdc4 (swap 10GB)
rest unallocated "free space"
I used Gparted to create the partitions. I ended up getting hung up on the "Create Filesystems" sections, specifically this line"
# mkfs.fat -F32 /dev/sdXY
Now that I am looking at it, I'm thinking the "Create Filesystems" section maybe isn't necessary because I've used Gparted?
If it isn't necessary, when I get to the "mount the EFI System Partition to /boot" section, would I simply use
# mount /dev/sdc1 /mnt/boot
instead of
# mount /dev/sdXY /mnt/boot ?
The way I had this setup with Ubuntu was 3 partitions on sdc (/, home, swap) and I set my PC to boot to the sdc drive on startup. The boot loader would then give me the option to boot into Ubuntu or Windows 7, and I never had to alter the sda or sdb drives at all. Is this possible through Arch? My thinking is that even if it isn't, I should still be able to enter the BIOS boot menu and select which drive to boot manually correct? That wouldn't be too big of a deal for me because I spend 90% of my time in Linux, and only use Windows for Photoshop and gaming occasionally.
Thanks for taking the time to read this. I would have just tested this out, but I am afraid of messing up my Windows install.

After several sleepless hours I had to give up and go to bed about 5 hours ago. The installation process went smoothly (or so I thought). I followed the tutorial closely and upon rebooting I was met with a blinking cursor. After some googling I found others who said I should press TAB, but nothing seemed to work.
I rebooted to the iso disk and found the "boot installed OS" option and noticed it said "Press TAB to edit". I then found the boot parameters and tried everything from hd0 0 to hd4 4. I believe I have Grub setup correctly because every option besides hd0 0 either says "Booting..." and then gets stuck, or says "That disk and partition combination does not exist". So yea, I think hd0 0 is the correct boot path, it just gets stuck with the blinking cursor.
silverhammermba wrote:
You have the right idea. You want to install a bootloader on sdc1 which will be able to boot both Arch and Windows.
Your best bet would be to use something like rEFInd. It has a "scanfor" option that should automatically detect your BIOS-configured Windows installation and add a boot option for it. Note that depending on your motherboard, you may have to switch to UEFI-only mode and Windows will be unbootable without the assistance of a UEFI program which is backwards compatible with BIOS (like rEFInd).
Thank you for the link. Considering I can't get into my install and the actual install only took about 30 minutes, I think I am going to just start from the beginning again with REFIndr. It seems much simpler. I only used Grub because I've used it before with Ubuntu, but my very limited knowledge is telling me Grub is probably the problem.
MoonSwan wrote:Just an idea: My bios has a "Boot-up Prompt" which I can invoke when it's POSTing by hitting F11. This brings me to a menu that allows me to choose which drive I want to boot up that day. I use it when Syslinux isn't working properly (Which is right now as a matter of fact ...) in order to boot Windows so I can do some SCII, for example. I, too, dual-boot but I have both OSes on different SSDs. So my 120GB Crucial SSD has Arch on it and the 240GB Kingston has Windows, SCII, Portable Apps, etc and nary the two shall meet. It makes dual-booting easier in the case of a corrupt OS or MBR or what-have-you. You may want to give your Bios a better look to see if you can do the F11 trick. It probably can and will usually tell you so at POST by printing that information on-screen along with your drives-detected and other messages (I hit Pause sometimes to read all the POST messages).
This is exactly what I was talking about doing when I mentioned:
My thinking is that even if it isn't, I should still be able to enter the BIOS boot menu and select which drive to boot manually correct?
That's good to know, because even if this next install doesn't work I think if I pull the other drives I should be able to get it working fairly easily.
Thanks again everyone.

Dual Boot Windows 7 and Arch with Shared NTFS partition.

Hi everyone,
I want to dual boot windows 7 and Arch Linux.
Here's the problem... my hard drive isn't the biggest. I want to store all my music, movies, pictures, and documents on partition that both linux and windows can access seamlessly.
I want the partition to be NTFS. -- (the programs that map an ext4 drive to Windows are trash).
Here's what I think I need.
30GB NTFS to Windows.
30GB ext4 to Arch Linux
The remainder (190ish GB) to Shared Data.
I don't want the swap partition because I have a SSD and 4GB of RAM.
What is the best way to setup my partitions? And is this even possible?
Thanks!

Not a problem. I would create:
First of four primary partitions for windows.
Second of four primary partitions for /boot
Third of four partitions is an extended partition encompassing all the space not used by the first two partitions.
Put everything else inside the extended partition.
Mine is a bit more complicated, but this should give you an idea:
ewaller@odin:~ 1005 %sudo fdisk -l /dev/sda
Password:
Disk /dev/sda: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x87b33479
Device Boot Start End Blocks Id System
/dev/sda1 * 2048 121778159 60888056 7 HPFS/NTFS/exFAT
/dev/sda2 597366784 625135615 13884416 83 Linux
/dev/sda3 121778160 597366783 237794312 5 Extended
/dev/sda5 * 121778223 123770219 995998+ 83 Linux
/dev/sda6 123770283 131770589 4000153+ 82 Linux swap / Solaris
/dev/sda7 193213818 597360959 202073571 83 Linux
/dev/sda8 131781258 193213754 30716248+ 83 Linux
/dev/sda9 131770591 131781194 5302 1 FAT12
Partition table entries are not in disk order
ewaller@odin:~ 1006 %
Partitions 1 and 2 are Primary partitions. Partition 3 is an extended partition. All the others live in partition 3

Dual boot windows 7 and solaris 11

Hi Friends,
Could some one please explain the steps to install dual boot windows 7 and solaris 11?
Thanks
Raja

Install Windows leaving a partition for Solaris. Install Solaris into the empty partition. Reboot. Use a partition manager if you need to shrink your current Windows Partition. GParted works great and is free.
alan

Dual Boot Windows 7 and solaris 10

Can some body guide me how to dual boot windows 7 and solaris 10?
Thanks

First partition your harddisk with at least 2 primary partitions, one for windows and the other for solaris if you only have one harddisk. It would be a good idea to create an additional small boot partition as the first partition as well if you intend on using an independent boot loader but it really depends on what your machine is capable of. For example, if you have multiple harddisk and your BIOS supports it, then you could just install each OS onto its own harddisk and use the BIOS function to disable/boot off specific harddisk. Otherwise, if you only have one harddisk and created multiple partitions, install windows7 first followed by solaris10, obviously installing into different partitions. If you have created a boot partition, then you can install the boot loader into that dedicated partition.

Dual Booting Windows and Solaris

Hi
how do i dual boot windows and solaris
Do i install windows first and then solaris or do it the other way around..?
how do i make sure that Windows and Solaris appear in my boot options..?
Is their a guide on doing this...?
Thanks
Liam

Hey I did a quick google search for you. So I havent tried this method myself but it sounds reasonable.
The text below is from the following link:
http://www.hccfl.edu/pollock/AUnix1/DualBoot.htm
"Solaris boot loader
Partition the drive to leave at least 2GB of space available for Solaris;
more drive space is desirable.
As with Linux, install Windows first then Solaris.
Do not use the Installation CD but boot and install
from Software CD 1.
If you accept the default partitioning scheme which
the installer provides you will soon run out of space in
your / and /usr partitions since only enough space is
allocated to install the system.
All extra space is allocated to /export/home.
A typical installation on a 4.5GB partition might look
something like this:
Filesystem Size Used Avail Use% Mounted on
/dev/dsk/c0d0s0 900M 536M 310M 64% /
/dev/dsk/c0d0s1 334M 109M 192M 36% /var
swap 671M 8.0k 671M 1% /var/run
swap 671M 8.0k 671M 1% /tmp
/dev/dsk/c0d0s5 845M 222M 565M 29% /opt
# (FAT32 partition):
/dev/dsk/c0d0p0:1 5.0G 3.3G 1.6G 66% /c
/dev/dsk/c0d0s7 1.1G 92M 954M 9% /export/home
/dev/dsk/c0d0s4 752M 225M 474M 33% /usr/local
The Solaris boot selector enables you to choose either
Solaris or Windows with Solaris as the default.
(I prefer grub or lilo!)
To mount FAT under Solaris:
# mount -F pcfs /dev/dsk/c0d0p0:c /dos (or �:1�?)
And the vfstab file:
/dev/dsk/c0d0p0:c - /dos pcfs - yes -
To create a GRUB boot floppy, follow these steps:
$ mkfs -t ext2 /dev/fd0
$ mount /dev/fd0 /mnt/fd0
$ mkdir /mnt/fd0/boot /mnt/fd0/boot/grub
$ cp /boot/grub/stage[12] /boot/grub/grub.conf \
> /mnt/fd0/boot/grub
$ /sbin/grub --batch <
Hope this helps!
/Oscar

Dual boot Windows Server 2008 R2 and RHEL 7 Server?

Do someone know how can I setup dual boot of Windows Server 2008 R2 and RHEL 7 Server?
I've tried to install Windows first, then shrink, then install RHEL there.
But GRUB2 loader doesn't offer to start Windows, only Linux in the menu. (probably Windows partition need to be added to grub2 somehow)

Hi Oleg Vazhnev,
Please refer to following article and check if can help you.
How
to add Vista/Windows 7 partition to Grub 2 (Ubuntu 9.10, Karmic Koala)
Please Note: Since the web site is not hosted by Microsoft, the link may change without notice. Microsoft
does not guarantee the accuracy of this information.
Meanwhile, please also refer to following video and check if can provide you more details of installation.
Install RHEL 7 in Legacy Mode (Dual Boot Windows Server
2008 R2)
Please Note: Since the web site is not hosted by Microsoft, the link may change without notice. Microsoft
does not guarantee the accuracy of this information.
If any update, please feel free to let me know.
Hope this helps.
Best regards,
Justin Gu

Re: Tecra S11 - Dual boot Windows 7 and XP

I have installed Windows 7 (from the hidden recovery section of the hardrive) on my new Tecra S11. I would like to know whether I can use the Windows XP
recovery media provided by Toshiba to create a dual boot Windows 7/Windows XP rather than reverting to XP?

You can create dual boot but not using two recovery images. Recovery image can be used for first OS installation. You cannot define on which partition the recovery image will be installed. It will always be installed on first partition.
I recommend you to do follow:
-at first install WXP using original Toshiba recovery disc
-Windows 7 install using Microsoft installation disc
I have done the same on my Satellite A300.

Advice on dual-booting Windows 7 with UEFI motherboard

I'm going to build a desktop PC tomorrow, having finally purchased all the parts for it. I'll be installing Arch as my main OS, and Windows for gaming. However I'm not really versed in UEFI and its uses, advantages/disadvantages; since my laptop just uses BIOS.
My plan is to have 3 drives: 32GB SSD for the / partition, 1TB HDD for /home, and 500GB for Windows 7 x64 Ultimate.
Being unused to UEFI I was thinking about trying to just run everything in BIOS/Legacy mode, but that doesn't seem very sensible to me, especially since I have the hardware so I might as well use it.
So, reading the wiki and forums have led me to conclude that having a 1GB EFI System Partition on the SSD should be sufficient, and use gummiboot for my bootloader.
Other reading about setting up dual boots suggests to me that installing Windows 7 on its own HDD with MBR partitioning and Arch on a separate (set of) drive(s) with GPT partitioning will be sufficient. The reason being that if the BIOS is set up to boot sda, which has GRUB as its bootloader, using GRUB I can choose to boot into Windows despite it being on a separate hard drive.
My questions are (and it occurs to me that I am in the most part just looking to have my ideas confirmed):
1. Have I gotten this all completely wrong?
2. If I'm correct, can the above system of using GRUB on one drive to boot up an OS on another drive be applied to UEFI?
3. Has anybody tried/succeeded/failed to dual-boot in this fashion before me, and if so what did they do?
Thanks one and all! Hopefully I've made myself clear enough here

billodwyer wrote:Being unused to UEFI I was thinking about trying to just run everything in BIOS/Legacy mode, but that doesn't seem very sensible to me, especially since I have the hardware so I might as well use it.
Using BIOS/CSM/legacy mode can work fine; however, it will probably slow down the boot process by a few seconds, and it will close off some possible future (and even current) advantages, as EFI support in Linux is improved.
So, reading the wiki and forums have led me to conclude that having a 1GB EFI System Partition on the SSD should be sufficient, and use gummiboot for my bootloader.
A 1GB ESP is more than sufficient. In terms of space requirements, 100-500MB is enough, depending on how you use the ESP; but various bugs and default settings make me recommend 550MiB as a good size. Bigger is OK, but wastes some disk space.
A bigger issue is that the ESP won't really benefit much from being on your SSD, since it's read once at boot time. The biggest advantage to putting the ESP on the SSD in your setup is that if you use gummiboot, you'll also have to put the Linux kernel and initrd file on the ESP, so having them on an SSD will speed up the boot process by about 1-5 seconds. Overall, I'd probably put the ESP on one of the spinning disks.
One more comment: gummiboot can launch boot loaders from its own partition but not from other partitions. This can work fine if you plan things carefully, but with three disks and two OSes, you must be absolutely positive that Windows uses the ESP on which gummiboot is installed. I'm not an expert on Windows installation, so I can't offer any specific pointers or caveats on this. If you need something with more flexibility, both rEFInd and GRUB can redirect the boot process to other partitions or physical disks. rEFInd can also redirect from an EFI-mode boot to a BIOS/CSM/legacy-mode boot. (See below.) Overall, rEFInd's flexibility on this score is a plus compared to gummiboot; but gummiboot is covered in the Arch wiki's beginner's guide, which is a plus. You'll have to pick which advantage you prefer. (Note that I'm rEFInd's maintainer, so I'm not unbiased.)
Other reading about setting up dual boots suggests to me that installing Windows 7 on its own HDD with MBR partitioning and Arch on a separate (set of) drive(s) with GPT partitioning will be sufficient. The reason being that if the BIOS is set up to boot sda, which has GRUB as its bootloader, using GRUB I can choose to boot into Windows despite it being on a separate hard drive.
This is an unworkable idea, at least as stated and if you want to do an EFI-mode boot. Windows ties the partition table type to the boot mode: Windows boots from MBR disks only in BIOS mode, and from GPT disks only in EFI mode. Thus, using MBR for the Windows disk will require a BIOS/CSM/legacy-mode installation of Windows. Furthermore, neither gummiboot nor GRUB can redirect from EFI mode to BIOS mode (or vice-versa), so if you do it this way, you'll be forcing yourself to boot Linux in BIOS mode, to switch between BIOS-mode and EFI-mode boots at the firmware level (which isn't always easily controlled), or to use rEFInd to redirect from an EFI-mode boot to a BIOS-mode Windows boot.
Overall, you're best off either using GPT for all your disks and booting all your OSes in EFI mode or using MBR for Windows (and perhaps all your disks) and using BIOS-mode booting for all your OSes.
Under EFI, the boot process is controlled by settings in the NVRAM, which you can adjust with "efibootmgr" in Linux, "bcfg" in an EFI shell, or "bcdedit" in Windows. (The Arch wiki covers the basics at least efibootmgr and bcfg.) In a typical dual-boot setup, you tell the computer to launch your preferred boot manager (EFI-mode GRUB, rEFInd, or gummiboot, most commonly), which then controls the boot process. You set up boot loaders for all your OSes on one or more ESPs. (Note: A boot manager lets you choose which boot loader to run, and a boot loader loads the kernel into memory. GRUB is both a boot manager and a boot loader. rEFInd and gummiboot are both boot managers. The EFI stub loader, ELILO, and the EFI version of SYSLINUX are all boot loaders but not boot managers. Most EFIs include their own boot manager, but it's usually primitive and awkward to use. It's also not standardized, so my computer's built-in boot manager is likely to be different from yours. Thus, I recommend against relying on the built-in boot manager for anything but launching your preferred boot manager.) Thus, the lowest-common-denominator type of setup is to put your preferred boot manager, the Windows boot loader, and a Linux boot loader (which could mean your Linux kernel) on a single ESP. If you want to use multiple ESPs or otherwise split things up, you cannot use gummiboot as the boot manager, since it can't redirect the boot process from one partition to another. (Many EFIs can do this with their own built-in boot managers, but this isn't guaranteed, and it's usually more awkward than using rEFInd or GRUB.)
I know this can be a lot to absorb. The official rules aren't really all that complex, but different EFIs interpret the rules differently, and the different capabilities of the various boot managers and boot loaders creates a lot of subtle implications for how you set everything up.
1. Have I gotten this all completely wrong?
Significant parts of it, I'm afraid; see above. You're working under BIOS assumptions, which don't apply to EFI.
2. If I'm correct, can the above system of using GRUB on one drive to boot up an OS on another drive be applied to UEFI?
GRUB can do this, but gummiboot can't. You set one of those (or something else, like rEFInd) as your primary boot manager. Using both GRUB and gummiboot adds unnecessary complexity, IMHO. OTOH, setting up multiple boot managers or boot loaders is possible, and can give you a fallback in case one fails. For instance, there's a known bug that affects 3.7 and later kernels, mostly on Lenovo computers, that causes the EFI stub loader to fail sometimes. Thus, if you use rEFInd, gummiboot, or the EFI's own boot manager to launch the kernel via the EFI stub loader, having GRUB, ELILO, or SYSLINUX set up as a fallback can provide helpful insurance in case a kernel upgrade causes your normal boot process to fail.
3. Has anybody tried/succeeded/failed to dual-boot in this fashion before me, and if so what did they do?
Many people dual-boot Windows and Linux under EFI. There are a huge number of possible solutions. My own Windows/Linux dual-boot system uses:
rEFInd
rEFInd's EFI filesystem drivers
Linux kernels on Linux-native /boot partitions (two partitions, one for each of the two distributions installed on that computer)
The Windows boot loader on the ESP
This works well for me, but it wouldn't work with gummiboot instead of rEFInd, since gummiboot can't redirect the boot process to another partition. (gummiboot also can't automatically load filesystem drivers.) Arch Linux users who use gummiboot often mount the ESP at /boot, which enables gummiboot to easily launch the Linux kernel. Doing this with multiple Linux distributions would be awkward, though, since you'd end up with two distributions' kernels in the same directory.

Dual boot windows mac mini

I got a Mac mini and in general I'm happy with it but found out that there's some software I use regularly that is just much better on Windows. They barely support OS X although technically they do. So I would like to dual boot Windows as it seems like this is supported and not crazy.
I followed the bootcamp and some guides I found via Google. I have the mac mini 2014 with 8 gig ram and 1 terabyte of space. I have dual monitors setup and a logitech mouse and a logitech gaming keyboard G110 - both USB. (I also own a wireless apple keyboard which I occasionally use with my iPad). My first problem was a DOS screen telling me I can't boot up on the specified disk but I did get some help off Google telling me to hold down option while booting (this should be in the guides ;p) but it was easy to fix.. however I'm stumped on what's happening now.
When I click the Windows partition, it starts booting up Windows 7 Premium 64 bit setup and all looks good. Then a screen pops up asking me what language/region I am. The default is United states (perfect). On this screen my keyboard and mouse are useless. Or it's frozen. I think the former. I think the computer just can't recognize them. And I cannot figure out a way around this. If anyone can - please help I will be very thankful.
I've tried booting up using the Windows 7 DVD I own and an ISO installed on a USB flash drive per the Bootcamp installer. Results are the same.

Use Boot Camp!! Sounds like you have the install disc. Make sure you completely erase a USB 2.0 Thumb Drive format it as one MS DOS Master Boot Record partition. Download Drivers to it. I checked this box in boot camp only.
Having install disc and driver thumb drive ready. Insert Windows install disc and plug in Thumb drive.
Open Boot Camp uncheck first 2 boxes. Continue
Size the BOOTCAMP partion you want it to be by sliding the bar. Or split your HD is an option.
After that is complete. You will be asked where to install. Select BOOTCAMP partition
Click Drive Options (advanced). Click Format. Click OK. All goes well you click Next and it will format as NTFS
Follow instructions to to install, set up and configure Windows.
GO TO APPLE SUPPORT no where else. PRINT BOOT CAMP Installation & Setup Guide. It is in my binder with my Windows 7 Professional Disc. You'll need this, I'm afraid, to have on hand. When Windows is up and going, Antivirus 1st, Install Windows express updates only. Do not update Apple drivers for Windows. Running Windows 7 Pro on my Mac Mini since I bought it in August. Use it for those outdated programs I can't run on Mac or Windows 8. Love it.
GET THE MANUAL Please. Have fun with it.
Oh, try left clicking your USB Mouse to make it work. If not use keyboard strokes. i.e. I a ccept the license agreement (note that the a is underlined. hit "a" on the keyboard to check box.

Dual boot Windows 7 partition help

I want to dual boot Windows 7 & arch but I need help with figuring out what partitions to make and where to put them because it seems the automatic partition-er won't do the trick for me.
I have two drives that I want to completely format for a fresh, clean install: a 60GB SSD & a 750GB hard drive. I want the end result to be that the SSD only has Windows 7 Pro x64 SP1 installed to it and I will point the 'My Documents', 'My Pictures', etc. to a NTFS partition on the hard disk drive ( I know how to do this folder pointing ). I don't want arch to touch the SSD if possible so I can reformat the SSD separately if I ever just want to reformat Windows. I only want arch to be on the hard disk for that reason. I don't think I care which one handles the OS switching at boot ( should I favor Windows MBR or syslinux? Please give advice. ) And I would assume I make the NTFS partition on the hard disk a primary partition so how do I split up arch for the 3 other primary partitions left since the auto partition from the arch boot CD uses 4?

I'm no expert, but the way I would do it would be like this:
1. Create partitions on the HDD for /, /boot, /home and swap, along with one (or more) for your Windows personal files
2. Set the BIOS to boot from the SSD.
3. Install Windows on the SSD.
4. Right-click the "My Documents" folder, select "properties", then the "Location" tab and choose the new location for the folder.
5. Install Arch on the HDD partitions, and allow the boot manager to install itself in the MBR of the SSD.
Then the whole boot process will be on the SSD... If you ever need to get rid of the Linux bootloader, you can overwrite it with a "clean" Windows one using bootrec.exe (see here: http://support.microsoft.com/kb/927392).
Last edited by esuhl (2012-03-26 04:52:12)

Advantages and Disadvantages of Dual booting Windows on PXI Device

Similar Messages

Maybe you are looking for