After Software Update 2007-004 airport card stopped working after wakeup

Hi,
I have a powerbook G4 - DVI running 10.3.9. After I have installed Software Update 2007-003, when my computer goes to sleep and then wakes up, airport card stops working. I had to open the back of the computer, unplug and plug the airport card, then it starts working again. But next time the computer goes to sleep, it stops working again.
Does anyone have a similar problem? Any work arounds?
Thanks in advance.
Also following is the logs from Software Update. Looks suspicious:
Mac OS X Version 10.3.9 (Build 7W98)
2007-04-28 18:56:03 -0400
2007-04-28 18:56:03.190 loginwindow[181] FSResolveAliasWithMountFlags returned err = -43
WirelessScan timeout waiting for first scan result
WirelessScan timeout waiting for first scan result

Deleting AppleAirPort2.kext solved the problem for some...
http://discussions.apple.com/thread.jspa?threadID=934370&tstart=0
While others had to rollback the AppleAirPort.kext to version...
http://discussions.apple.com/thread.jspa?messageID=4310165&#4310165
Installing the Security update 1.0.1 from 5/01/2007 helped others. Reapplying the Combo Update again helped a couple of people.

Similar Messages

After Service, Airport card stops working randomly on macbook pro 17" early 2009

Hi,
So after the last time my computer was serviced, the airport card stops working randomly on moving the screen.
Upons restarting the computer, it sometimes says wi-fi hardware not installed. Then, if I move my machine around,
lift it up, turn it around, place it back on the table and restart it, it works again. I don't understand this.
And all this started happening the moment my warranty ran out. Extremely frustrating!!

It may be possible that one of the following may be the issue:
The internal AirPort Extreme card is not seated properly.
The internal Wi-Fi antenna connector is not seated properly in the AirPort Extreme card.
The internal AirPort Extreme card's connector is faulty or damaged.
The internal AirPort Extreme card is faulty.
To get an idea on how the Extreme card is installed, please check out the following iFixit article.

Airport Problems after Security Update 2007-004

Ever since I've installed Security Update 2007-004 my Airport connection has been dropping about every 15 to 30 minutes. Sometimes Airport will stay connected but will stop working until I renew my DHCP lease (I get the same IP though). When it drops I click on the Airport icon to reconnect but my network doesn't always show up. Sometimes I have to turn Airport off and back on again to make it show up, and a few times I've had to reset my computer to make it show up.
I have a MacBook Pro with an 802.11n card. I'm using two different routers; one at work, and one at home. The work router is a Linksys N router while the one at home is a Linksys G router.
I've tried all the tricks. Repairing Permissions, deleting the extension caches, installing the standalone updater, but nothing is working.

Deleting AppleAirPort2.kext solved the problem for some...
http://discussions.apple.com/thread.jspa?threadID=934370&tstart=0
While others had to rollback the AppleAirPort.kext to version...
http://discussions.apple.com/thread.jspa?messageID=4310165&#4310165
Installing the Security update 1.0.1 from 5/01/2007 helped others. Reapplying the Combo Update again helped a couple of people.

Mail (and Safari) won't open after Security Update 2007-004

I have a PowerBook G4 running 10.3.9. The machine was running fine (I was checking mail, browsing the web) when my weekly scheduled update opened. Per it's suggestion, I installed Security Update 2007-004.
Upon restart, both Mail and Safari will NOT open. The icon for each on the dock simply "bounces" once when clicked then nothing else. Has anyone else experienced anything similar? Any thoughts on a fix?

Installing a system update while you continue using the computer as if nothing was going on there is a really bad idea.
Verify/repair the startup disk (not just permissions), as described here:
The Repair functions of Disk Utility: what's it all about?
After having fixed all the filesystem issues, if any, reinstall the Security Update, which may not have been installed properly. It may also be necessary to reinstall the Combo Update for the type of computer and the version of Mac OS X you’re using, unless this is the version of Mac OS X that came with the computer:
Mac OS X 10.3.9 Combo Update
Take a look at the following articles for guidelines on how to properly install system updates:
Troubleshooting installation and software updates
Installing software updates
Basically, you should verify/repair the startup disk before installing the update, no applications should be running while installing it, and you may experience unexpected results if you have third-party system software modifications (not normal applications) installed.

Latest Apple Software Update causes 'No Airport card installed' error

Hi,
I accepted the Software Update released 05Apr08 and rebooted. Following the reboot my MacBook Air now says 'no airport card installed' and I can't get the MacBook to 're-recognize' the card.
I have used the airport card to access many different wireless networks prior to this update with no issues.
All advice accepted gratefully.
Thanks.

I'm having the same problem with a brand new Macbook Air I picked up on Tuesday. When I got it home I updated all software to latest, and didn't have any issues...
Sometime on Thursday, however, after waking from sleep the airport card reported it is off, and no amount of attempting to turn it on again would successfully do so. After a restart, the computer reported no Airport card is installed at all. I had to shut down the computer and turn it back on before the airport card was recognized (and work) again. This is now the case every time the computer is put to sleep. Occasionally after I do this, the network will be incredibly slow, something like dialup speeds.
First I tried resetting the PMU (http://docs.info.apple.com/article.html?artnum=14449), but that didn't work. Then I reset the PRAM and NVRAM (http://docs.info.apple.com/article.html?artnum=2238), which worked for only about a day. Now here I am again with the same issue, and an appointment for the genius bar at 5pm tonight.

Prey game not launching after Security Update 2007-004

After applying Apple Security Update 2007-004, Prey (Mac version) is not launching and continuously crashes on my computer. I have uninstalled all game files and reinstalled the game from the original DVD but with no success. Repairing disc permissions, updating prebindings and other usual maintainence meaures are unfortunately not helping. I have an external USB hard disc running Mac OS 10.4.9 without the Security Update applied and Prey works properly when my computer boots up from this external hard drive. It is therefore apparent that Apple Security Update 2007-004 has most probably caused Prey to become non-functional as prior to this the game was working without any problems whatsoever.
Has anyone else expereinced this problem and are there any suggestions?
Any advice is greatly appreciated.

Contact the game author's site and report it so they can update it.

After software Update (2006-07), airport can not connect to the router

Hi,
I installed the software update 2006-07. Afterwards the airport extreme can not connect to the router anymore (NETGEAR). I use a WEP key, but even if I type the WEP Key, the airport does not succeed to the router anymore... I called Apple Care and they wanted that I install the firmware restoration. But even I didn't succeed to install the firmware restoration. On the firmware restoration web page (http://www.apple.com/support/downloads/firmwarerestorationcd12.html) is written that I have to turn on the computer and continue holding down the power button until the LED blinks rapidly followed immediately by a successive series of blinks (3 quick blinks, 3 slow blinks, 3 quick blinks). But after the LED blinks, there is not the successive series of blinks...
I know there is 2 questions in one message, but could you please help?
Thanks in advance.
Best regards,
Eric
MacBook Pro Intel Core 2 Duo Mac OS X (10.4.8)

http://forums.macosxhints.com/showthread.php?p=337100
Exactly the same problems as mentioned here kernel panics, etc. How could this have passed Apple Quality Checks?
Tue Dec 5 09:26:34 2006
panic(cpu 0 caller 0x000A8800): Uncorrectable machine check: pc = 000000003931288C, msr = 0000000000149030, dsisr = 40000000, dar = 000000003A207F7E
AsyncSrc = 0000000000000000, CoreFIR = 0000000000000000
L2FIR = 0000000000000000, BusFir = 0000000000000000
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000A8800 0x000A7A90 0x000AB780
Proceeding back via exception chain:
Exception state (sv=0x39D1B780)
PC=0x3931288C; MSR=0x00149030; DAR=0x3A207F7E; DSISR=0x40000000; LR=0x39312858; R1=0x2285BA10; XCP=0x00000008 (0x200 - Machine check)
Backtrace:
0x39312848 0x393139B8 0x39333874 0x393336BC 0x393332F0 0x3933313C
0x002D124C 0x393314AC 0x39332774 0x002EB838 0x0008C6A4 0x0002921C 0x000233F8 0x000ABAAC
0x00000000
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.AppleAirPort2(405.1)@0x392f4000
dependency: com.apple.iokit.IONetworkingFamily(1.5.0)@0x386e6000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x32922000
Exception state (sv=0x39D3A780)
PC=0x9000AB48; MSR=0x0200F030; DAR=0x003B8000; DSISR=0x42000000; LR=0x9000AA9C; R1=0xBFFFCCA0; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
Just by enabling the airport express card. Now I wonder what triggers the bug. Because I rebooted several times after the update. One thing I did see was the signal strength going less strong in the past days. Since today I cannot use it at all.

After Security Update 2010-001: Airport Card Not Detected

Currently running OS X 10.5.8 on a Mid 2009 MacBook Pro.
Here's the issue. When I boot up the machine and click the AirPort drop down it tells me that there is no airport card detected. Under system profiler it says the same thing. If I boot to a 10.6 Mac OS Install DVD and open system profiler, the AirPort card is detected. This occurred after a reboot prompted by the Security Update 2010-001.
So far I have repaired permissions and repaired disk. No fix.
I reset the PRAM/NVRAM and SMC. No fix.
I booted to an OS X image on an external drive. No fix.
I cannot boot to the Apple Hardware Test (D at startup) because my company requires PGP disk encryption. I could decrypt but this would take at least 6 hours (not counting re-encrypting afterwards).
I tried replacing the extensions. No fix.
There were no firmware updates applied or any other major OS updates.
Anyone have anything else I can attempt?

anyone else see that??
Yes, Already covered in full here. Strange but no problem.
http://discussions.apple.com/thread.jspa?threadID=2310982&tstart=15

T410 - Sound card stopped working after Lenovo System Update

hi all!
yesterday I performed a system update trough the ThinkVantage System Update 3, I chose a complete update (even the BIOS).
After the update, the sound card is not working anymore: everything in the control panel looks fine, volume is up and all's connected, but no sound is coming out, with the exception of the skype system sound when starting/quitting the application...
No system restore is possible (it looks disabled by our IT dept), updated the drivers via windows update, but no help.
Any clue?
Thanks in advance!
Riccardo
Solved!
Go to Solution.

Remove the audio-driver via Controlpanel - Add/Remove Software
Download the audio driver from Lenovo
Install the driver manually
My home-forum: http://www.thinkpad-forum.de
Wiki: Deutsches ThinkPad-Wiki English ThinkWiki
My ThinkPad-Collection

Why i cannot restore back after software update?, why i cannot restore back after software update?, why i cannot restore back after software update?

Why i cannot restore back after update software?

What does "restore back" mean?
If it means go backwards to some earlier version of iOS, then Apple has never allowed that.
If it means reload the contents of your iPhone after doing a software update, you should be able to do that.

After latest update Mountain Lion, fan never stop working!

Hi all
After latest update (26/9/2012 in my case) of Mountain Lion, the fan start working and never stops (Macbook pro 5,5).
Any other have sam issue?
Already tried to reboot SMC and delete everything starting from snow leopard but problem still exist!!!
Thanks.

I keep an old wired keyboard and wired mouse for just such emergencies, but that is not helping you now. There are at least a couple of things that could account for the disappearance of the Bluetooth preference pane.
There may have been a glitch in the installation.
The preference pane will not be displayed if the bluetooth transceiver was not detected when the computer started.
This may seem too obvious, but try completely powering down using the power button on your Mac mini. Wait at least 30 seconds for everything in the mini to fully discharge. While you are waiting to restart, check/replace the batteries in your wireless keyboard and mouse or trackpad. Restart using the power button on the Mac mini.
If that does not work almost anything else will require the use of a wired keyboard and mouse. For years I have kept a wired keyboard and mouse around for just such an emergency, but in a fit of spring cleaning they were discarded. I ended up having to buy a cheap USB mouse and keyboard at Radio Shack (under $20 for the pair but no command key). But, with any kind of luck, you should be able to borrow a wired keyboard and mouse to get this fixed. Once you have a functioning keyboard and mouse you could...
Be sure Bluetooth is turned ON in System Preferences
Install the OS X 10.8.4 (Combo) updater or
Boot into the recovery drive (Reboot while holding down Command + R) and reinstall OS X 10.8.4

3.1.3 software update has made my iPod stop working correctly

I have a 2nd generation 16 GB iPod touch. I purchased the 3.1 update when it came out. I had some problems with my iPod after that update, but these problems were resolved when the next update came out (3.1.2 I think). Last week I did the next iPod update-3.1.3. Now my iPod is worse than before. My movies and podcasts won't download from my iTunes library, sometimes when I sync my iPod, it appears there is no music or anything on it (which was what happened after the first update). However when I go into "Settings", it says it has no songs, but all the capacity is all used up. I have to go back in to sync again, but i might have to do this 3 or 4 times before it puts my songs back on my iPod. I'd like to know how to uninstall the last update i did and just go back to the 3.1.2 version. Or if anyone knows what I should do please let me know. Please.....this is so aggravating. I wish I had never done this last update!

Just plug it into your computer and restore it through iTunes. You can try restore from backup first and, if the problems go away, then you are done. If not, restore again and select restore as new. You can resync all of your content when done.

After downloading updates in C5 camera raw stopped working. I am trying to download DNG CONVERTOR but when I press 'download' it just times out.

After downloading updates in C5, camera rawstopped working. I am trying to download DNG CONVERTOR but when I press 'Download' it just times out. Is Photoshop having problems as I have tried for three days now.

BOILERPLATE TEXT:
If you give complete and detailed information about your setup and the issue at hand, such as your platform (Mac or Win), exact versions of your OS, of Photoshop and of Bridge, machine specs, what troubleshooting steps you have taken so far, what error message(s) you receive, if having issues opening raw files also the exact camera make and model that generated them, etc., someone may be able to help you.
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

[SOLVED] DVB-C card stopped working (after update?)

edit: Marked as solved because the problem hasn't occurred for years.
I have a TechnoTrend TT-Budget C-1501 PCI DVB-C card which used to work fine. Today I installed a bunch of updates including new kernel and now the card doesn't work. Current kernel version is 3.9.2-1-ARCH, as reported by uname -r. I don't remember the kernel version which was installed when the card worked but I installed Arch about a month ago and this was the first upgrade.
dmesg gives the following information:
$ dmesg | grep -i dvb
[ 1.663037] saa7146: register extension 'budget_ci dvb'
[ 1.663232] DVB: registering new adapter (TT-Budget C-1501 PCI)
[ 1.718876] input: Budget-CI dvb ir receiver saa7146 (0) as /devices/pci0000:00/0000:00:1c.4/0000:03:00.0/0000:04:01.0/rc/rc0/input13
[ 1.719068] rc0: Budget-CI dvb ir receiver saa7146 (0) as /devices/pci0000:00/0000:00:1c.4/0000:03:00.0/0000:04:01.0/rc/rc0
[ 1.721746] DVB: TDA10023(-1): tda10023_writereg, writereg error (reg == 0x00, val == 0x33, ret == -121)
[ 1.771639] DVB: TDA10023(-1): tda10023_readreg: readreg error (reg == 0x1a, ret == -121)
This problem seems to be relatively common with cards containing the TDA10023 chip but I haven't found a proper solution. Is this just a bug or should I adjust something?
EDIT: I forgot to mention that the card works on Windows.
Hardware specs:
Intel Xeon E3-1230v2 CPU
16GB of RAM
ASRock H77 Pro4/MVP motherboard (BIOS/UEFI version seems to be the latest (1.50))
Geforce GTX 650 Ti
Last edited by ormu (2015-04-07 16:01:12)

Weird, now it's working again after "cold" boot... Could the Windows driver load a different firmware which doesn't work properly on Linux? I think I used the card on Windows just before rebooting to Arch...
$ dmesg | grep -i dvb
[ 1.651217] saa7146: register extension 'budget_ci dvb'
[ 1.651361] DVB: registering new adapter (TT-Budget C-1501 PCI)
[ 1.708299] input: Budget-CI dvb ir receiver saa7146 (0) as /devices/pci0000:00/0000:00:1c.4/0000:03:00.0/0000:04:01.0/rc/rc0/input13
[ 1.708338] rc0: Budget-CI dvb ir receiver saa7146 (0) as /devices/pci0000:00/0000:00:1c.4/0000:03:00.0/0000:04:01.0/rc/rc0
[ 1.711359] budget_ci dvb 0000:04:01.0: DVB: registering adapter 0 frontend 0 (Philips TDA10023 DVB-C)...

White screen - no startup after software updates 2007-007

I cannot start my mac g4 following a software upgrade I did last night. There were a series of upgrades. I just get a white screen and it will not boot. In the meantime, I cleared a partition on a second drive on the same machine and installed 10.4 on this and have used it to start up and look at the other drive. I have been backing up files onto one of my external drives but running out of disk space. I am really concerned since all my apps are on the original volume and I don't believe I can just transfer them. Problem is my partition on the drive I set up is also small (about 10gb) so thats not much room for anything more than the os plus a bit. Should I attempt to fix the original volume, should I try an archive and install, some advice really appreciated. Many thanks.

Hi there. Thanks for your advice. It is not practical to back up everything and I have backups of the files that are important but no one really wants to loose anything when you are confronted with making choices like this.
That said, I think some responsibility falls on Apple's shoulders to ensure that the older machines will update properly since it appears there are many g4's still in service. I have located another post similar to mine today that indicates this is not isolated to me - which leads me to believe it may just be a bad update.
Obviously there was some adverse effect from the new software since the system was good until the reboot with the updates. While I shouldn't expect this to occur, I get you're point about being prepared in the event it does. From my perspective, this experience is something that you'd expect from $MS. I have never had this type of experience after using a Mac now for almost 10 years. Worst case was a failing second drive (Maxtor) that I installed - but was able to recover the data using the Carbon Copy app.
In any case, I appreciate any replies and am hopeful I'll have recovered by the end of the day . Many thanks.

After Software Update 2007-004 airport card stopped working after wakeup

Similar Messages

Maybe you are looking for