AIR-LAP1310G-E-K9 acces point not joining to 5508 wlan controller

Question

Hi,
I have Cisco AIR-LAP1310G-E-K9 access point and 5508 wlan controller with version 7.0.220 and it is joining to the WLAN controller.  I have enabled dhcp in the lan controller and i dont have external dns server. How to fix this issue?  Can this LAN controller version will support this access point? 
My Lan Controller Management IP Address is 10.10.10.5
Please find the below configuration of 1300 access point.
AP001d.4513.dd68#reload
Proceed with reload? [confirm]
%SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command.
%LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.
flashfs[0]: 4 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 2052608
flashfs[0]: Bytes available: 5688832
flashfs[0]: flashfs fsck took 14 seconds.
Base ethernet MAC Address: 00:1d:45:13:dd:68
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Unable to get our ip address: no "IP_ADDR" variable set
The system has been encountered and error initializing
tftp file system. The system is ignoring the error and
continuing boot. If you interrupt the system boot process,
the following commands will set IP_ADDR, DEFAULT_ROUTER
and NETMASK environment variables, initializing tftp file
system, and finish loading the operating system software:
    set IP_ADDR
    set DEFAULT_ROUTER
    set NETMASK
    tftp_init
    boot
Loading "flash:/c1310-rcvk9w8-mx/c1310-rcvk9w8-mx"...############################################################################################################################################################################################
File "flash:/c1310-rcvk9w8-mx/c1310-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1310 Software (C1310-RCVK9W8-M), Version 12.4(10b)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Wed 19-Mar-08 19:09 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x003BE9E0
Initializing flashfs...
flashfs[1]: 4 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 7741440
flashfs[1]: Bytes used: 2052608
flashfs[1]: Bytes available: 5688832
flashfs[1]: flashfs fsck took 2 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1310G-E-K9R   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FHK1133E002
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from reload
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:1D:45:13:DD:68
Part Number                          : 73-8960-09
PCA Assembly Number                  : 800-24963-06
PCA Revision Number                  : A0
PCB Serial Number                    : FOC113000V7
Top Assembly Part Number             : 800-28479-05
Top Assembly Serial Number           : FHK1133E002
Top Revision Number                  : B0
Product/Model Number                 : AIR-LAP1310G-E-K9R
The name for the keys will be: ap.cisco.com
% The key modulus size is 1024 bits
% Generating 1024 bit RSA keys, keys will be non-exportable...[OK]
ip ssh version 2
    ^
% Invalid input detected at '^' marker.
transport input ssh
                 ^
% Invalid input detected at '^' marker.
aaa new-model
^
% Invalid input detected at '^' marker.
aaa authentication login default enable local none
^
% Invalid input detected at '^' marker.
o
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar  1 00:00:05.442: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar  1 00:00:06.473: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar  1 00:00:07.817: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1310 Software (C1310-RCVK9W8-M), Version 12.4(10b)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Wed 19-Mar-08 19:09 by prod_rel_team
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
transport input ssh
                 ^
% Invalid input detected at '^' marker.
*Mar  1 00:00:33.860: %LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER
*Mar  1 00:00:33.860: %LWAPP-3-CLIENTERRORLOG: DNS Name Lookup: could not resolve CISCO-LWAPP-CONTROLLER
*Mar  1 00:00:33.861: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
logging origin-id string AP:001d.4513.dd68
         ^
% Invalid input detected at '^' marker.
logging 255.255.255.255
        ^
% Invalid input detected at '^' marker.
logging trap 3
        ^
% Invalid input detected at '^' marker.
*Mar  1 00:00:37.440: Logging LWAPP message to 255.255.255.255.
AP001d.4513.dd68>
%LWAPP-3-CLIENTEVENTLOG: Forcing AP to obtain IP address using DHCP
%DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.10.10.46, mask 255.255.255.0, hostname AP001d.4513.dd68
Translating "CISCO-LWAPP-CONTROLLER.CISCO-LWAPP-CONTROLLER.mydomain.com"...domain server (10.10.10.5)
%LWAPP-3-CLIENTEVENTLOG: Did not get vendor specific options from DHCP.
%LWAPP-3-CLIENTEVENTLOG: Did not get log server settings from DHCP.
%LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER.CISCO-LWAPP-CONTROLLER.mydomain.com
%LWAPP-3-CLIENTERRORLOG: DNS Name Lookup: could not resolve CISCO-LWAPP-CONTROLLER.CISCO-LWAPP-CONTROLLER.mydomain.com
AP001d.4513.dd68>

Answer 1

Your debug is very telling ..
AP001d.4513.dd68>
%LWAPP-3-CLIENTEVENTLOG: Forcing AP to obtain IP address using DHCP
%DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.10.10.46, mask 255.255.255.0, hostname AP001d.4513.dd68
Translating "CISCO-LWAPP-CONTROLLER.CISCO-LWAPP-CONTROLLER.mydomain.com"...domain server (10.10.10.5)
%LWAPP-3-CLIENTEVENTLOG: Did not get vendor specific options from DHCP.
%LWAPP-3-CLIENTEVENTLOG: Did not get log server settings from DHCP.
%LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER.CISCO-LWAPP-CONTROLLER.mydomain.com
%LWAPP-3-CLIENTERRORLOG: DNS Name Lookup: could not resolve CISCO-LWAPP-CONTROLLER.CISCO-LWAPP-CONTROLLER.mydomain.com
AP001d.4513.dd68>
What are you using to tell the AP where the contoller lives ? Since you are consoled into the ap you can use the -> capwap ap controller ip address
This will point the ap to your controller
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."