AIR-LAP521G-E-K9 is not joining WLC4402-12

Hi,
Please I need some help with any guide or info regarding my LAP521 access points that are refusing to join the WLC4402-12.
This is my first lightweight access point implementation and I have 3 LAP521's and 1 AIR-CAP3502I-E-K9 access points on my network.
They are meant to pick up ip address from external dhcp server and then join the WLC but only the 3502i joins successfuly while the 521's get dhcp address but do not join the WLC. From the logs, I can see that the WLC is discovered by the 521's and even get a response message from the controller but they are still unable to join as shown in the screenshot below.
My WLC is running software version 7.0.230.0 and the 521's are running an lwapp image version 4.2.61.8.
Base Radio MAC
AP Name
Status
Ethernet MAC
IP Address
Last Join Time
00:23:04:cc:56:d0
NA
Not Joined
00:00:00:00:00:00
172.31.5.115
00:23:04:f2:8d:10
NA
Not Joined
00:00:00:00:00:00
172.31.5.113
00:23:33:22:3d:b0
NA
Not Joined
00:00:00:00:00:00
172.31.5.110
3c:ce:73:94:b4:d0
AP001
Joined
44:2b:03:6d:5d:50
172.31.5.120
Oct 01 18:01:17.713
Please any suggestions or help with resolving this issue will be appreciated.
Thanks

The reason the 521 will not join, is because they require the Cisco Express WLC. They will not join the 4400 WLC. Take a look at this matrix with the code you are running and the AP's that are supported.
http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html#wp81600
Sent from Cisco Technical Support iPhone App

Similar Messages

  • AIR-CAP3502I-E-K9 does not join preferred controller

    I have an AIR-CAP3502I-E-K9 AP that is configured for two WLAN controllers with preferred order. However the AP does not join the primary controller, but uses the secondary one instead. I have a bunch of these AIR-CAP3502I-E-K9s , majority work fine, but three of them not.
    I have tried commands according to
    https://supportforums.cisco.com/docs/DOC-24917
    In the controller's GUI  the order is properly configured. I also tried to use 'Clear All Config" option on the controller and configured the AP from the scratch, but this did not help.
    Here is what I have
    XXXX#sh capwap client config
    configMagicMark         0xF1E2D3C4
    chkSumV2                30883
    chkSumV1                1073
    swVer                   7.2.111.3
    adminState              ADMIN_ENABLED(1)
    name                    XXXX
    location                YYYY
    group name
    mwarName                ZZZZ1
    mwarIPAddress           192.168.1.1
    mwarName                ZZZZ2
    mwarIPAddress           192.168.1.2
    mwarName
    mwarIPAddress           0.0.0.0
    ssh status              Enabled
    Telnet status           Enabled
    numOfSlots              2
    spamRebootOnAssert      1
    spamStatTimer           180
    randSeed                0xBAC2
    transport               SPAM_TRANSPORT_L3(2)
    transportCfg            SPAM_TRANSPORT_DEFAULT(0)
    initialisation          SPAM_PRODUCTION_DISCOVERY(1)
    ApMode                  Local
    ApSubMode               Not Configured
    AP Rogue Detection Mode Enabled
    OfficeExtend AP         [0] Disabled
    OfficeExtend AP JoinMode[0] Standard
    Discovery Timer         10 secs
    Heart Beat Timer        30 secs
    Led State Enabled       1
    Primed Interval         0
    AP ILP Pre-Standard Switch Support Disabled
    AP Power Injector Disabled
    Infrastructure MFP validation Disabled
    Configured Switch 1 Addr 192.168.1.2
    Configured Switch 2 Addr 192.168.1.1
    non-occupancy channels:
    Ethernet (Duplex/Speed) auto/auto
    *Mar  1 00:14:23.001: %CAPWAP-3-ERRORLOG: Selected MWAR 'ZZZZ2'(index 1).
    *Mar  1 00:14:23.001: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Aug 22 12:21:57.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
    *Aug 22 12:21:57.581: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
    *Aug 22 12:21:57.581: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    My primary one is 192.168.1.1 and secondary is 192.168.1.2, but the AP joins always the secondary one.
    The lines above
    Configured Switch 1 Addr 192.168.1.2
    Configured Switch 2 Addr 192.168.1.1
    seem to be suspicious, I would expect the reverse order, but do not know how the code did it.
    The only guess is that in the very beginning the AP joined 192.168.1.2, and this was the controller I configured the AP initially from. The AP seems to maybe somehow remember this.
    OS version is
    swVer                   7.2.111.3
    Thanks,
    Vlad

    Yes, this is what I am trying all the time - configure the AP to point to the WLCs I want it to join.
    Firstly I did through GUI, did not work.
    Secondly I  used 'Clear All Config" option on the controller and configured the AP from the scratch through GUI, did not work.
    Thirdly I tried through command line on the AP, did not work.
    I used these commands
    XXXX#capwap ap  primary-base ZZZZ1 192.168.1.1
    XXXX#capwap ap  secondary-base ZZZZ2 192.168.1.2
    XXXX#sh capwap client config
    configMagicMark         0xF1E2D3C4
    chkSumV2                30883
    chkSumV1                1072
    swVer                   7.2.111.3
    adminState              ADMIN_ENABLED(1)
    name                    XXXX
    location                YYYY
    group name
    mwarName                ZZZZ1
    mwarIPAddress           192.168.1.1
    mwarName                ZZZZ2
    mwarIPAddress           192.168.1.2
    mwarName
    mwarIPAddress           0.0.0.0
    ssh status              Enabled
    Telnet status           Enabled
    numOfSlots              2
    spamRebootOnAssert      1
    spamStatTimer           180
    randSeed                0xBAC2
    transport               SPAM_TRANSPORT_L3(2)
    transportCfg            SPAM_TRANSPORT_DEFAULT(0)
    initialisation          SPAM_PRODUCTION_DISCOVERY(1)
    ApMode                  Local
    ApSubMode               Not Configured
    AP Rogue Detection Mode Enabled
    OfficeExtend AP         [0] Disabled
    OfficeExtend AP JoinMode[0] Standard
    Discovery Timer         10 secs
    Heart Beat Timer        30 secs
    Led State Enabled       1
    Primed Interval         0
    AP ILP Pre-Standard Switch Support Disabled
    AP Power Injector Disabled
    Infrastructure MFP validation Disabled
    Configured Switch 1 Addr 192.168.1.2
    Configured Switch 2 Addr 192.168.1.1
    non-occupancy channels:
    Ethernet (Duplex/Speed) auto/auto
    XXXX#sh log
    Syslog logging: enabled (1 messages dropped, 8 messages rate-limited,
                    0 flushes, 0 overruns, xml disabled, filtering disabled)
        Console logging: level debugging, 61 messages logged, xml disabled,
                         filtering disabled
        Monitor logging: level debugging, 0 messages logged, xml disabled,
                         filtering disabled
        Buffer logging: level debugging, 67 messages logged, xml disabled,
                        filtering disabled
        Logging Exception size (4096 bytes)
        Count and timestamp logging messages: disabled
        Trap logging: level emergencies, 0 message lines logged
            Logging to 255.255.255.255(global) (udp port 514, audit disabled,  link down), 0 message lines logged, xml disabled,
                   filtering disabled
    Log Buffer (1048576 bytes):
    *Mar  1 00:00:09.424: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:09.434: *** CRASH_LOG = YES
    *Mar  1 00:00:09.434: 64bit PCIE devicesSecurity Core found.
    Base Ethernet MAC address: E0:5F:B9:A8:00:7F
    *Mar  1 00:00:12.482: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:13.731: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:13.797: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:16.996: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
    *Mar  1 00:00:17.052: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)
    *Mar  1 00:00:17.068:  status of voice_diag_test from WLC is false
    *Mar  1 00:00:19.182: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 12.4(25e)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2012 by Cisco Systems, Inc.
    Compiled Fri 14-Sep-12 19:13 by prod_rel_team
    *Mar  1 00:00:19.182: %SNMP-5-COLDSTART: SNMP agent on host XXXX is undergoing a cold start
    *Mar  1 00:13:33.342: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:13:33.342: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:13:33.493:  status of voice_diag_test from WLC is false
    *Mar  1 00:13:33.632: %SSH-5-ENABLED: SSH 2.0 has been enabledlwapp_crypto_init: MIC Present and Parsed Successfully
    *Mar  1 00:13:33.956: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:13:34.343: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:13:34.343: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:13:36.029: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:13:41.484: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.1.21, mask 255.255.255.0, hostname XXXX
    *Mar  1 00:13:51.981: Logging LWAPP message to 255.255.255.255.
    *Mar  1 00:14:01.997: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Mar  1 00:14:06.099: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Mar  1 00:14:07.190: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:14:08.191: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Mar  1 00:14:08.288: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:14:09.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:14:11.000: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
    *Mar  1 00:14:23.001: %CAPWAP-3-ERRORLOG: Selected MWAR 'ZZZZ2'(index 1).
    *Mar  1 00:14:23.001: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Aug 23 06:07:13.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
    *Aug 23 06:07:13.578: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
    *Aug 23 06:07:13.578: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    *Aug 23 06:07:14.025: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
    *Aug 23 06:07:14.091: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Aug 23 06:07:14.094: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller ZZZZ2
    *Aug 23 06:07:14.154: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    What I think might be the key to the problem is this
    Configured Switch 1 Addr 192.168.1.2
    Configured Switch 2 Addr 192.168.1.1
    This is not changing no matter what I do.
    Thanks,
    Vlad

  • AIR-CAP3501I access point not joining the Cisco 2100 Wireless Lan controller.

    Hello All,
    I am installing a new LAP (AIR-CAP3501I ) through the wireless lan controller (AIR-WLC2112-K9) with software version 7.0. I have an external ADSL modem which will act as the DHCP server for the wireless clients and the LAP.
    Please find my network setup as below:
    The ISP ADSL modem , WLC and LAP are connected to a unmanaged POE switch. The LAP gets its power through the POE switch. When i connect the LAP and the WLC to the switch along with the ADSL modem, the LAPs are getting the ip address from the ADSL modem, however they are not joining the WLC for further process.
    ADSL Modem ip address: 192.168.1.254
    Management ip address on the LAP: 192.168.1.1 ( Assigned to port 1, untagged Vlan).
    Ap Manager ip address: 192.168.1.1 ( Assigned to the same port i.e port1, Untagged Vlan).
    The LAP is getting an IP address from the ADSL modem in the range of the DHCP scope.
    I will paste the logs very soon.
    Please let me know if i am doing anything wrong oe what will be the issue.
    Thanks in advance,
    Mohammed Ameen

    Hello All,
    Please find the logs for  "debug capwap event" from the WLC below:
    *spamReceiveTask: Sep 26 19:44:59.196: e8:04:62:0a:3f:10 Join Version: = 117465600
    *spamReceiveTask: Sep 26 19:44:59.197: e8:04:62:0a:3f:10 Join resp: CAPWAP Maximum Msg element len = 92
    *spamReceiveTask: Sep 26 19:44:59.197: e8:04:62:0a:3f:10 Join Response sent to 192.168.1.156:45510
    *spamReceiveTask: Sep 26 19:44:59.197: e8:04:62:0a:3f:10 CAPWAP State: Join
    *spamReceiveTask: Sep 26 19:44:59.197: e8:04:62:0a:3f:10 capwap_ac_platform.c:1216 - Operation State 0 ===> 4
    *apfReceiveTask: Sep 26 19:44:59.198: e8:04:62:0a:3f:10 Register LWAPP event for AP e8:04:62:0a:3f:10 slot 0
    *spamReceiveTask: Sep 26 19:44:59.341: e8:04:62:0a:d1:20 DTLS connection not found, creating new connection for 192:168:1:158 (45644) 192:168:1:2 (5246)
    *spamReceiveTask: Sep 26 19:45:00.119: e8:04:62:0a:d1:20 DTLS Session established server (192.168.1.2:5246), client (192.168.1.158:45644)
    *spamReceiveTask: Sep 26 19:45:00.119: e8:04:62:0a:d1:20 Starting wait join timer for AP: 192.168.1.158:45644
    *spamReceiveTask: Sep 26 19:45:00.121: e8:04:62:0a:d1:20 Join Request from 192.168.1.158:45644
    *spamReceiveTask: Sep 26 19:45:00.123: e8:04:62:0a:d1:20 Join Version: = 117465600
    *spamReceiveTask: Sep 26 19:45:00.123: e8:04:62:0a:d1:20 Join resp: CAPWAP Maximum Msg element len = 92
    *spamReceiveTask: Sep 26 19:45:00.124: e8:04:62:0a:d1:20 Join Response sent to 192.168.1.158:45644
    *spamReceiveTask: Sep 26 19:45:00.124: e8:04:62:0a:d1:20 CAPWAP State: Join
    *spamReceiveTask: Sep 26 19:45:00.124: e8:04:62:0a:d1:20 capwap_ac_platform.c:1216 - Operation State 0 ===> 4
    *apfReceiveTask: Sep 26 19:45:00.125: e8:04:62:0a:d1:20 Register LWAPP event for AP e8:04:62:0a:d1:20 slot 0
    *spamReceiveTask: Sep 26 19:45:00.273: e8:04:62:0a:d1:20 Configuration Status from 192.168.1.158:45644
    *spamReceiveTask: Sep 26 19:45:00.273: e8:04:62:0a:d1:20 CAPWAP State: Configure
    *spamReceiveTask: Sep 26 19:45:00.273: Invalid channel 1 spacified for the AP APf866.f2ab.24b6, slotId = 0
    *spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 Updating IP info for AP e8:04:62:0a:d1:20 -- static 0, 192.168.1.158/255.255.255.0, gtw 192.168.1.254
    *spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 Updating IP 192.168.1.158 ===> 192.168.1.158 for AP e8:04:62:0a:d1:20
    *spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 Setting MTU to 1485
    *spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 Finding DTLS connection to delete for AP (192:168:1:158/45644)
    *spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 Disconnecting DTLS Capwap-Ctrl session 0xa06d6a4 for AP (192:168:1:158/45644)
    *spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 CAPWAP State: Dtls tear down
    *spamReceiveTask: Sep 26 19:45:00.277: spamProcessGlobalPathMtuUpdate: Changing Global LRAD MTU to 576
    *spamReceiveTask: Sep 26 19:45:00.277: e8:04:62:0a:d1:20 DTLS connection closed event receivedserver (192:168:1:2/5246) client 192:168:1:158/45644).
    The Acess point joins the Controller for 2-3 seconds and then unjoins again. I am not sure what i am doing wrong here. The access points are getting the IPs from the ADSL modem through the switch, then it talks to the WLC, however it does not join the controller for further process.
    Note:
    The Managemnet interface and the AP manager interface are assigned to the same port 1 with unassigned Vlan as mention above.

  • IMP: Cisco AIR-CAP1602 &1532 not joining 2504 Controller issue

    Dear Team, We have Cisco wireless implementation in clients premises. We have 8 indoor AP (AIR-CAP1602E-AK9) and 2 Outdoor AP (AIR-CAP1532I-AK9) . Seven indoor APs are able to join the 2504 controller, but 1 indoor AIR-CAP1602E AP is not joining and signal is RED continuously while as outdoor AP AIR-CAP1532I-AK9 signal goes blinking from green, red to amber continuously and is not downloading LWAPP image from the controller even after hard reset.
    The output for both APs shown below-
    1) AIR-CAP1602E-A-K9:
    C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Compiled Fri 30-Nov-12 15:48 by aselvara
    ap: reset
    Are you sure you want to reset the system (y/n)?y
    System resetting...
    Boot from flash
    IOS Bootloader - Starting system.
     FLASH CHIP: Spansion S25FL256
    Xmodem file system is available.
    flashfs[0]: 14 files, 3 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31936000
    flashfs[0]: Bytes used: 418304
    flashfs[0]: Bytes available: 31517696
    flashfs[0]: flashfs fsck took 9 seconds.
    Reading cookie from SEEPROM
    Base Ethernet MAC address: 18:e7:28:d1:9b:05
     ************* loopback_mode = 0
    The system is unable to boot automatically because there
    are no bootable files.
    C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Compiled Fri 30-Nov-12 15:48 by aselvarag
    Same event repeating, failed to reset and reboot device
    2) AIR_CAP1532I-A-K9 (Outdoor AP):
     *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
    *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_47:32:e4'running version 7.5.102.0 is rejected.
    *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 100.1.1.20
    signal goes blinking from Grean, Red to Amber continuously.
    Failed to download LWAPP image from the controller even after hard reset.
    Default image: 7.6.95.12
    Logs and screen shot attached
    Please advice. 
    Thanks
    Aakash

    Hi please note the details below-
    AIR-CAP1602E-A-K9:
    C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Compiled Fri 30-Nov-12 15:48 by aselvara
    ap: reset
    Are you sure you want to reset the system (y/n)?y
    System resetting...
    Boot from flash
    IOS Bootloader - Starting system.
     FLASH CHIP: Spansion S25FL256
    Xmodem file system is available.
    flashfs[0]: 14 files, 3 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31936000
    flashfs[0]: Bytes used: 418304
    flashfs[0]: Bytes available: 31517696
    flashfs[0]: flashfs fsck took 9 seconds.
    Reading cookie from SEEPROM
    Base Ethernet MAC address: 18:e7:28:d1:9b:05
     ************* loopback_mode = 0
    The system is unable to boot automatically because there
    is no bootable files.
    C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Compiled Fri 30-Nov-12 15:48 by aselvarag
    Can't reboot device!
    WLC-SYSLOG
    (Cisco Controller) >show sysinfo
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.5.102.0
    Bootloader Version............................... 1.0.18
    Field Recovery Image Version..................... 1.0.0
    Firmware Version................................. PIC 16.0
    Build Type....................................... DATA + WPS
    System Name...................................... Cisco_47:32:e4
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
    IP Address....................................... 100.1.1.20
    Last Reset....................................... Power on reset
    System Up Time................................... 0 days 2 hrs 18 mins 39 secs
    System Timezone Location......................... (GMT -6:00) Central Time (US a                                                                                        nd Canada)
    System Stats Realtime Interval................... 5
    System Stats Normal Interval..................... 180
    --More-- or (q)uit
    Configured Country............................... US  - United States
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +32 C
    External Temperature............................. +37 C
    Fan Status....................................... 4000 rpm
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 3
    Number of Active Clients......................... 0
    Burned-in MAC Address............................ 24:E9:B3:47:32:E0
    Maximum number of APs supported.................. 15

  • When I attempt to connect my new MacBook Air to my home network I receive a dialogue that says " Could not join name of network .  A connection timeout has occurred.  Any ideas on how to deal with this?

    When I attempt to connect my new MacBook Air to my home network I receive a dialogue that says " Could not join <name of network>.  A connection timeout has occurred.  Any ideas on how to deal with this?

    Please review the following Apple Support article for assistance with troubleshooting wireless connections.
    You may also find this OSXDaily article helpful as well.

  • AIR-LAP1242G-E-K9 do not work with AIR-CT5508-K9 while AIR-LAP1142N-E-K9 do

    Hello,
    we do have a site where we need to deploy AIR-LAP1142N-E-K9 and AIR-LAP1242G-E-K9 APs. We have two AIR-CT5508-K9 controllers with SW version                  6.0.188.0.
    AIR-LAP1142N-E-K9s work okay, as expected, we do not have any problems with them.
    However AIR-LAP1242G-E-K9s do not, there is a problem with establishing CAPWAP tunnel with the controller.The AP is seen on the controller for a while, with 0 time up-time, cannot change any settings on the AP via controller, and after a while it disapears from the controller, apears again and this repeats.
    The APs and controllers are connected to the LAN campus.
    Controllers via two 1G links configured as Etherchannel to WS-C6506-E VSS switch with s72033-ipservicesk9_wan-vz.122-33.SXI1.bin on it.
    APs to WS-C3750G-48PS with c3750-ipbasek9-mz.122-50.SE2.bin on it. 3750 is connected to the C6505 via two 1G links configured as Etherchannel.
    Below I copied the log I captured on 1242 and the controller. Highlighted ones are the ones which I think might bring a clue.
    I performed some troubleshooting steps.
    - As we have some other controllers available over WAN, I  tested the 1242 AP  with 2100, 4400 and also with the same model AIR-CT5508-K9 with SW version                  6.0.188.0 over WAN and this worked always okay.
    - I wanted to be sure that I eliminate any kind of out of sequence packet issue, so I brought down all redundancy L2 links so that the L2 path from the AP to the controller was only through one leg links.
    - I also brought the second controller down to eliminate potential issue with having two of them up.
    - The AP gets its IP from DHCP configured on the C6506 switch, I am always able to ssh to AP, so the IP connectivity does not seem to be an issue.
    - I have more 1242s, all behave in the same way. I also connected them to some other 3750 switches we have in the campus, always the same.
    - As this seems to be maybe a kind of ssl issue, I tried to play with controller settings, like enabling Accept... options  under Security/AP Policy,but this did not help.
    - I also tried to reboot the controller, no improvement.
    - The APs came from the factory, so in the beginning everything was factory default in them. They were always able to download the image from the controller in the very initial phase. I still do have some of them untouched, so I can perform any troubleshooting steps with the fresh one.
    I can reproduce this, can also send debugging logs if needed.
    Any idea on what could be wrong is highly appreciated.
    Thank you.
    +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    This Discussion has been converted into document:- https://supportforums.cisco.com/docs/DOC-23054
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    AIR-LAP1242G-E-K9 10.0.13.28 log
    *Mar  1 00:00:05.922: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:07.536: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot1 1Radio 0
    *Mar  1 00:00:07.672: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 304 messages)
    *Mar  1 00:00:09.809: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
    *Mar  1 00:00:09.874: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2009 by Cisco Systems, Inc.
    Compiled Mon 02-Nov-09 18:42 by prod_rel_team
    *Mar  1 00:00:09.874: %SNMP-5-COLDSTART: SNMP agent on host wuen4028 is undergoing a cold start
    *Mar  1 00:00:09.964: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Mar  1 00:00:09.967: bsnInitRcbSlot: slot 1 has NO radio
    *Mar  1 00:00:10.191: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:10.191: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:10.430: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:00:10.818: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
    *Mar  1 00:00:11.212: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:18.315: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.0.13.28, mask 2 55.255.255.0, hostname wuen4028
    *Mar  1 00:00:28.988: Logging LWAPP message to 255.255.255.255.
    *Mar  1 00:00:31.456: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Mar  1 00:00:31.495: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:32.457: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:32.457: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
    *Mar  1 00:00:38.810: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Mar  1 00:00:47.811: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
    *Mar  1 00:00:56.812: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
    *Mar  1 00:01:07.815: %CAPWAP-3-ERRORLOG: Selected MWAR 'wuen4001'(index 0).
    *Mar  1 00:01:07.815: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Feb 11 07:52:24.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.13.5 peer_port: 5246
    *Feb 11 07:52:24.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Feb 11 07:52:25.441: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.0.13.5 peer_port:  5246
    *Feb 11 07:52:25.443: %CAPWAP-5-SENDJOIN: sending Join Request to 10.0.13.5
    *Feb 11 07:52:25.443: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *Feb 11 07:52:25.445: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 10.0.13.5
    *Feb 11 07:52:25.445: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 4.
    *Feb 11 07:52:25.445: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Feb 11 07:52:25.445: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.0.13.5
    *Feb 11 07:52:30.441: %CAPWAP-5-SENDJOIN: sending Join Request to 10.0.13.5
    *Feb 11 07:52:30.442: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 10.0.13.5
    *Feb 11 07:52:30.443: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 4.
    *Feb 11 07:52:30.443: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Feb 11 07:52:30.443: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.0.13.5
    *Feb 11 07:52:47.644: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Feb 11 07:53:23.999: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.0.13.5:5246
    *Feb 11 07:53:24.000: %CAPWAP-3-ERRORLOG: Selected MWAR 'wuen4001'(index 0).
    *Feb 11 07:53:24.000: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Feb 11 07:52:24.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.13.5 peer_port: 5246
    *Feb 11 07:52:24.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Feb 11 07:52:24.001: %DTLS-5-PEER_DISCONNECT: Peer 10.0.13.5 has closed connection.
    *Feb 11 07:52:24.001: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.0.13.5:5246
    *Feb 11 07:52:24.002: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 3 combination.
    *Feb 11 07:52:24.123: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is not established.
    wuen4028#
    AIR-CT5508-K9 10.0.13.5 log
    *Feb 11 09:00:54.824: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:2171 Failed to c
    omplete DTLS handshake with peer 10.0.13.28
                                               *Feb 11 08:59:53.798: %DOT1X-3-MAX_EA
    P_RETRIES: 1x_auth_pae.c:2862 Max EAP identity request retries (3) exceeded for
    client 00:1f:3b:93:dd:4f
    *Feb 11 08:59:51.197: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
    ity request retries (3) exceeded for client 00:c0:a8:e1:b1:71
    --More-- or (q)uit
    *Feb 11 08:59:21.212: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:292 RRM LOG: Airewave Di
    rector: Could not find valid channel lists for 802.11bg
    *Feb 11 08:58:39.766: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:2171 Failed to c
    omplete DTLS handshake with peer 10.0.13.28
                                               *Feb 11 08:57:06.131: %RRM-3-RRM_LOGM
    SG: rrmChanUtils.c:292 RRM LOG: Airewave Director: Could not find valid channel
    lists for 802.11bg
    *Feb 11 08:56:24.504: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:2171 Failed to c
    omplete DTLS handshake with peer 10.0.13.28
                                               *Feb 11 08:55:09.693: %DOT1X-3-MAX_EA
    P_RETRIES: 1x_auth_pae.c:2862 Max EAP identity request retries (3) exceeded for
    client 00:1f:3b:93:dd:4f
    *Feb 11 08:54:51.040: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:292 RRM LOG: Airewave Di
    rector: Could not find valid channel lists for 802.11bg
    *Feb 11 08:53:56.493: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmis
    sions exceeded for client 00:1f:3b:93:dd:4f
    *Feb 11 08:53:34.497: %DTL-3-OSARP_DEL_FAILED: dtl_arp.c:1380 Unable to delete a
    n ARP entry for 10.0.13.28 from the operating system. ioctl operation failed
    *Feb 11 08:52:35.936: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:292 RRM LOG: Airewave Di
    rector: Could not find valid channel lists for 802.11bg
    *Feb 11 08:52:26.492: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmis
    sions exceeded for client 00:1f:3b:93:dd:4f
    *Feb 11 08:50:07.680: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmis
    sions exceeded for client 00:1f:3b:93:e6:57
    *Feb 11 08:48:37.458: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
    ity request retries (3) exceeded for client 00:1f:3b:93:e6:57
    *Feb 11 08:47:37.438: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmis
    sions exceeded for client 00:1f:3b:93:e6:57
    *Feb 11 08:47:34.438: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
    ity request retries (3) exceeded for client 00:16:44:1d:0f:53
    *Feb 11 08:46:32.422: %DOT1X-3-MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:407 Max EAPOL-ke
    y M3 retransmissions exceeded for client 00:16:44:1d:0f:53
    *Feb 11 08:46:06.790: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
    ity request retries (3) exceeded for client 00:1f:3b:95:61:bd
    *Feb 11 08:46:06.789: %DOT1X-3-ABORT_AUTH: 1x_bauth_sm.c:447 Authentication abor
    ted for client 00:1f:3b:95:61:bd
    *Feb 11 08:46:06.210: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
    ity request retries (3) exceeded for client 00:1f:3b:93:e6:57
    *Feb 11 08:45:34.304: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
    ity request retries (3) exceeded for client 00:1f:3b:95:61:bd
    *Feb 11 08:45:34.303: %DOT1X-3-ABORT_AUTH: 1x_bauth_sm.c:447 Authentication abor
    ted for client 00:1f:3b:95:61:bd
    *Feb 11 08:45:01.298: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:292 RRM LOG: Airewave Di
    rector: Could not find valid channel lists for 802.11bg
    *Feb 11 08:44:38.076: %SIM-3-PORT_UP: sim.c:9547 Physical port 2 is up!.
    *Feb 11 08:44:38.037: %SIM-3-PORT_UP: sim.c:9547 Physical port 1 is up!.
    --More-- or (q)uit
    *Feb 11 08:44:38.009: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'cliWebInitParms.cfg'
    *Feb 11 08:44:37.980: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'rrcEngineInitParms.cfg'
    *Feb 11 08:44:37.980: %CNFGR-3-INV_COMP_ID: cnfgr.c:2105 Invalid Component Id :
    Unrecognized (81) in cfgConfiguratorInit.
    *Feb 11 08:44:37.928: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'rfidInitParms.cfg'
    *Feb 11 08:44:37.915: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'dhcpParms.cfg'
    *Feb 11 08:44:37.903: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'bcastInitParms.cfg'
    *Feb 11 08:44:37.834: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'rrmInitParms.cfg'
    *Feb 11 08:44:27.331: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'apfInitParms.cfg'                                            
    *Feb 11 08:44:27.226: %MM-3-MEMBER_ADD_FAILED: mm_dir.c:903 Could not add Mobili
    ty Member. Reason: IP already assigned, Member-Count:1,MAC: 00:00:00:00:00:00, I
    P: 0.0.0.0
    *Feb 11 08:44:27.023: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'mmInitParms.cfg'
    *Feb 11 08:44:27.013: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'aaaapiInitParms.cfg'
    *Feb 11 08:44:27.011: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'pemInitParms.cfg'
    *Feb 11 08:44:26.898: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'dot1xInitParms.cfg'
    *Feb 11 08:44:26.868: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'capwapInitParms.cfg'
    *Feb 11 08:44:26.718: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'spamInitParms.cfg'
    *Feb 11 08:44:25.650: %SSHPM-3-FREAD_FAILED: sshpmlscscep.c:1395 Error reading f
    ile /mnt/application/lscca_pem.crt
    *Feb 11 08:44:06.435: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'sshpmInitParms.cfg'  

    Thanks for such quick response and suggestions.
    Yes, I seem not to to be 100% perfect as for the list of troubleshooting steps I took.
    I had already tried the two commands you mentioned. I tried again, this time with some other 1242, but these do not help.
    Yes, I was already thinking that this could be in theory a licensing issue. The controller is bougth with 25 licenses.
    In the beginnign I had one 1142 on it and tried to enable 1242s which did not work. Now I have five 1142s on it, as this worked okay, I guess it could not be a licensing issue.
    I think that I can see in the log files that the machines communicate to each other, L2 or L3 paths seem to be working okay. I forgot to mention that I am using option 43 on the DHCP server, so the AP clearly finds its way to the controller. What's more both APs and the controllers are in the same VLAN, so they are in the same broadcast domain.
    Below is sho ver from the AP. The AP seems to have Certificate type - manufacture installed, so I guess there should not be a problem with the certificate, especially knowing that the AP works with other controllers over WAN.
    My guess these messages seen on AP especially "Invalid event 38 & state 3 combination" might tell us what's wrong.
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman";
    mso-ansi-language:#0400;
    mso-fareast-language:#0400;
    mso-bidi-language:#0400;}
    *Feb 11 07:52:24.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Feb 11 07:52:24.001: %DTLS-5-PEER_DISCONNECT: Peer 10.0.13.5 has closed connection.
    *Feb 11 07:52:24.001: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.0.13.5:5246
    *Feb 11 07:52:24.002: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 3 combination.
    *Feb 11 07:52:24.123: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is not established.
    Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2009 by Cisco Systems, Inc.
    Compiled Mon 02-Nov-09 18:42 by prod_rel_team
    ROM: Bootstrap program is C1240 boot loader
    BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
    AP9caf.ca00.1c78 uptime is 17 minutes
    System returned to ROM by power-on
    System image file is "flash:/c1240-k9w8-mx.124-21a.JA2/c1240-k9w8-mx.124-21a.JA2"
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-LAP1242G-E-K9    (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
    Processor board ID FCZ135082GH
    PowerPCElvis CPU at 262Mhz, revision number 0x0950
    Last reset from power-on
    LWAPP image version 6.0.188.0
    1 FastEthernet interface
    1 802.11 Radio(s)
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 9C:AF:CA:00:1C:78
    Part Number                          : 73-11479-01
    PCA Assembly Number                  : 800-30493-01
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC13484GYY
    Top Assembly Part Number             : 800-29589-03
    Top Assembly Serial Number           : FCZ135082GH
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-LAP1242G-E-K9
    Configuration register is 0xF
    AP9caf.ca00.1c78#

  • I can not join my Apple extreme with the Apple express. I shows a conflict in the network! I've tried everything. How can they join on the same network?

    I can not join my Apple extreme with the Apple express. I shows a conflict in the network! I've tried everything. How can they join on the same network?

    It says that my DHCP has to be changed! How? to what?
    It is 802.11g.express. but is set to default by the computer (Macbook Air).
    The other is 802.11n. (express)
    Extreme is 802.11.g. Is the Main Airport.
    It is on ethernet & wep 128 security.

  • 3702i AP's not Joining WLC - Layer 3 discovery request not received on management VLAN

    Hi Guys, 
    This is a follow up post to this thread: https://supportforums.cisco.com/discussion/12400481/3702i-not-joint-2504
    Have been playing around with my AP's and made sure the time is correct on all the devices ( WLC and Switch). I have also moved the AP's to the same Vlan as the management IP of the WLC. 
    if I move the AP's to the same Vlan as the WLC they join and are happy, as soon as I move them to a different Vlan they cant join and there time goes back to the default plus they do not seem to save the WLC details to flash but still remember the test names I give them.
    it appears that option 43 is working fine as I can see it look for the WLC IP and I have done some trouble shooting on the WLC and it looks like it see's the AP but doesn't except it.
    please see below for the boot up of the AP and the WLC logs: 
    AP 
    IIOS Bootloader - Starting system.
    *** deleted for breverity ***** 
    Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1"...#########################
    File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1" uncompressed and installed, entry point: 0x2003000
    executing...
    Secondary Bootloader - Starting system.
    Montserrat Board
    *** deleted for breverity ***** 
    Boot CMD: 'boot  flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1;flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1'
    Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1"...###############################################
    File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1" uncompressed and installed, entry point: 0x1003000
    executing...
                  *** deleted for breverity ***** 
    cisco AIR-CAP3702I-Z-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
    Processor board ID FGL1838X4T1
    PowerPC CPU at 800Mhz, revision number 0x2151
    Last reset from power-on
    LWAPP image version 8.0.110.0
    1 Gigabit Ethernet interface
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: F4:4E:05:B7:1E:84
    Part Number                          : 73-15243-01
    PCA Assembly Number                  : 000-00000-00
    PCA Revision Number                  :
    PCB Serial Number                    : FOC18343WPR
    Top Assembly Part Number             : 068-05054-03
    Top Assembly Serial Number           : FGL1838X4T1
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP3702I-Z-K9
    % Please define a domain-name first.
    Press RETURN to get started!
    *Mar  1 00:00:19.295: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
    *Mar  1 00:00:19.755: Registering HW DTLS
    *Mar  1 00:00:19.763: APAVC: Initial WLAN Buffers Given to System is  2500
    *Mar  1 00:00:19.815: APAVC:  WlanPAKs 42878 RadioPaks  42270
    *Mar  1 00:00:22.127: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:26.055: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
    *Mar  1 00:00:26.167: Loading Power Tables from ram:/Q2.bin. Class = A
    *Mar  1 00:00:26.167:  record size of 3ss: 1168 read_ptr: 4F9698E
    *Mar  1 00:00:31.207: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
    *Mar  1 00:00:31.251: Loading Power Tables from ram:/Q5.bin. Class = Z
    *Mar  1 00:00:31.251:  record size of vht: 2904 read_ptr: 4F9698E
    *Mar  1 00:00:31.407: Wait until the stile protocol list is initialized.
    *Mar  1 00:00:32.651: Start STILE Activation
    *Mar  1 00:00:34.571: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
    *Mar  1 00:00:35.447: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 19-Dec-14 11:20 by prod_rel_team
    *Mar  1 00:00:35.447: %SNMP-5-COLDSTART: SNMP agent on host Test_1 is undergoing a cold start
    *Mar  1 00:00:36.563: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:37.787: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
    *Mar  1 00:00:37.939: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:37.939: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:00:47.567: %LINK-6-UPDOWN: Interface BVI1, changed state to down
    *Mar  1 00:00:48.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
    *Mar  1 00:00:50.431: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
    *Mar  1 00:00:50.431: DPAA Initialization Complete
    *Mar  1 00:00:50.431: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
    *Mar  1 00:00:51.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:53.435: %LINK-6-UPDOWN: Interface BVI1, changed state to up
    *Mar  1 00:00:53.867: Currently running a Release Image
    *Mar  1 00:00:54.287: Incorrect certificate in SHA2 PB !
    *Mar  1 00:00:54.287: Using SHA-1 signed certificate for image signing validation.
    *Mar  1 00:00:54.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:59.787: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.2, mask 255.255.255.0, hostname Test_1
    *Mar  1 00:01:02.707: APAVC: Succeeded to activate all the STILE protocols.
    *Mar  1 00:01:02.707: APAVC: Registering with CFT
    *Mar  1 00:01:02.707: APAVC: CFT registration of delete callback succeeded
    *Mar  1 00:01:02.707: APAVC: Reattaching  Original Buffer pool for system use
    *Mar  1 00:01:02.707: Pool-ReAtach: paks 42878 radio42270
    %Default route without gateway, if not a point-to-point interface, may impact performance
    *Mar  1 00:01:10.103: AP image integrity check PASSED
    *Mar  1 00:01:10.187: Incorrect certificate in SHA2 PB !
    *Mar  1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:01:11.591: %CDP_PD-4-POWER_OK: 15.4 W power - NEGOTIATED inline power source
    *Mar  1 00:01:12.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:01:13.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:01:13.947: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:01:14.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Mar  1 00:01:20.211: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:01:31.215: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
    *Mar  1 00:02:11.599: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Mar  1 00:02:11.603: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    *Mar  1 00:02:11.611: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:02:12.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:02:12.639: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:02:12.647: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Mar  1 00:02:12.655: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:02:13.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:02:13.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:02:13.699: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:02:14.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    Not in Bound state.
    *Mar  1 00:02:44.719: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
    *Mar  1 00:02:49.839: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.3, mask 255.255.255.0, hostname Test_1
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:02:55.719: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
    Not in Bound state.
    *Mar  1 00:03:59.219: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
    *Mar  1 00:04:04.343: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.4, mask 255.255.255.0, hostname Test_1
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:04:10.223: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
    WLC: 
    isco Controller) >show time
    Time............................................. Tue Jan 27 17:44:47 2015
    Timezone delta................................... 0:0
    Timezone location................................ (GMT +8:00) HongKong, Bejing, Chongquing
    NTP Servers
        NTP Polling Interval.........................     3600
         Index     NTP Key Index                  NTP Server                  NTP Msg Auth Status
           1              0                             150.101.176.226       AUTH DISABLED
    (Cisco Controller) >show ap join stats summary  
    Incorrect input! Use 'show ap join stats summary [all/<ap-mac>]'
    (Cisco Controller) >show ap join stats summary all 
    Number of APs.............................................. 2 
    Base Mac             AP EthernetMac       AP Name                 IP Address         Status
    f4:4e:05:aa:a6:a0    f4:4e:05:94:c3:98    APf44e.0594.c398        10.1.1.22          Joined    
    f4:4e:05:b6:ce:f0    N A                  Test_1                  10.1.20.7          Not Joined
    (Cisco Controller) >show ap join stats detailed f4:4e:05:b6:ce:f0
    Sync phase statistics
    - Time at sync request received............................ Not applicable
    - Time at sync completed................................... Not applicable
    Discovery phase statistics
    - Discovery requests received.............................. 45
    - Successful discovery responses sent...................... 21
    - Unsuccessful discovery request processing................ 24
    - Reason for last unsuccessful discovery attempt........... Layer 3 discovery request not received on management VLAN
    - Time at last successful discovery attempt................ Jan 27 17:45:49.705
    - Time at last unsuccessful discovery attempt.............. Jan 27 17:45:49.705
    Join phase statistics
    - Join requests received................................... 0
    - Successful join responses sent........................... 0
    - Unsuccessful join request processing..................... 0
    - Reason for last unsuccessful join attempt................ Not applicable
    - Time at last successful join attempt..................... Not applicable
    - Time at last unsuccessful join attempt................... Not applicable
    Configuration phase statistics
    --More-- or (q)uit
    - Configuration requests received.......................... 0
    - Successful configuration responses sent.................. 0
    - Unsuccessful configuration request processing............ 0
    - Reason for last unsuccessful configuration attempt....... Not applicable
    - Time at last successful configuration attempt............ Not applicable
    - Time at last unsuccessful configuration attempt.......... Not applicable
    Last AP message decryption failure details
    - Reason for last message decryption failure............... Not applicable
    Last AP disconnect details
    - Reason for last AP connection failure.................... Not applicable
    - Last AP disconnect reason................................ Not applicable
    Last join error summary
    - Type of error that occurred last......................... Lwapp discovery request rejected
    - Reason for error that occurred last...................... Layer 3 discovery request not received on management VLAN
    - Time at which the last join error occurred............... Jan 27 17:45:49.705
    AP disconnect details
    - Reason for last AP connection failure.................... Not applicable
                                                                               Ethernet Mac : 00:00:00:00:00:00  Ip Address : 10.1.20.7
    (Cisco Controller) >show interface summary 
     Number of Interfaces.......................... 4
    Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Guest
    ap                               LAG  20       10.1.20.231     Dynamic No     No   
    guest                            LAG  30       10.1.30.231     Dynamic No     No   
    management                       LAG  10       10.1.1.231      Static  Yes    No   
    virtual                          N/A  N/A      1.1.1.1         Static  No     No   
    SWITCH
    witch#show run
    Building configuration...
    *** deleted for breverity ***** 
    no aaa new-model
    clock timezone AWST 8
    system mtu routing 1500
    ip routing
    ip dhcp pool WAP_Pool
       network 10.1.20.0 255.255.255.0
       default-router 10.1.20.1 
       option 43 hex f104.0a01.01e7
    ip dhcp pool Clients
       network 10.1.30.0 255.255.255.0
       default-router 10.1.30.1 
       dns-server 203.0.178.191 
    ip dhcp pool test
       network 10.1.1.0 255.255.255.0
       default-router 10.1.1.1 
    crypto pki trustpoint TP-self-signed-4082587776
     enrollment selfsigned
     subject-name cn=IOS-Self-Signed-Certificate-4082587776
     revocation-check none
     rsakeypair TP-self-signed-4082587776
    *** deleted for breverity ***** 
    *** deleted for breverity ***** !
    interface FastEthernet0/3
     description *** WLC ****
     switchport trunk encapsulation dot1q
     switchport mode trunk
    interface FastEthernet0/4
     description **** AP *****
     switchport access vlan 20
     switchport mode access
     spanning-tree portfast
    interface FastEthernet0/5
     description **** AP ****
     switchport access vlan 20
     switchport mode access
     spanning-tree portfast
    interface FastEthernet0/6
    i*** deleted for breverity ***** !
    interface Vlan10
     description *** Managment ***
     ip address 10.1.1.230 255.255.255.0
    interface Vlan20
     description *** WIRELESS APS ***
     ip address 10.1.20.1 255.255.255.0
    interface Vlan30
     ip address 10.1.30.1 255.255.255.0
    ip classless
    ip route 0.0.0.0 0.0.0.0 10.1.1.1
    ip http server
    ip http secure-server
    ip sla enable reaction-alerts
    l*** deleted for breverity ***** 
    ntp clock-period 36028827
    ntp source FastEthernet0/1
    ntp server 121.0.0.42
    ntp server 202.127.210.37
    end
    I have also placed a Device in Vlan 20 and it is able to ping the WLC and the WLC can ping it s routing is working. 
    Thanks 

    Hey Scott, 
    I gave that a shot and still no luck, log's from AP boot up:
    IIOS Bootloader - Starting system.
    flash is writable
    Tide XL MB - 40MB of flash
    Xmodem file system is available.
    flashfs[0]: 67 files, 9 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 41158656
    flashfs[0]: Bytes used: 20894208
    flashfs[0]: Bytes available: 20264448
    flashfs[0]: flashfs fsck took 20 seconds.
    Base Ethernet MAC address: f4:4e:05:b7:1e:84
    Ethernet speed is 100 Mb - FULL Duplex
    Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1"...#########################
    File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1" uncompressed and installed, entry point: 0x2003000
    executing...
    Secondary Bootloader - Starting system.
    Montserrat Board
    40MB format
    Tide XL MB - 40MB of flash
    Xmodem file system is available.
    flashfs[0]: 67 files, 9 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 41158656
    flashfs[0]: Bytes used: 20894208
    flashfs[0]: Bytes available: 20264448
    flashfs[0]: flashfs fsck took 21 seconds.
    flashfs[1]: 0 files, 1 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 12257280
    flashfs[1]: Bytes used: 1024
    flashfs[1]: Bytes available: 12256256
    flashfs[1]: flashfs fsck took 1 seconds.
    Base Ethernet MAC address: f4:4e:05:b7:1e:84
    Boot CMD: 'boot  flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1;flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1'
    Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1"...###############################################
    File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1" uncompressed and installed, entry point: 0x1003000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 19-Dec-14 11:20 by prod_rel_team
    Montserrat Board
    40MB format
    Tide XL MB - 40MB of flash
    Initializing flashfs...
    flashfs[2]: 67 files, 9 directories
    flashfs[2]: 0 orphaned files, 0 orphaned directories
    flashfs[2]: Total bytes: 40900608
    flashfs[2]: Bytes used: 20894208
    flashfs[2]: Bytes available: 20006400
    flashfs[2]: flashfs fsck took 14 seconds.
    flashfs[2]: Initialization complete.
    flashfs[4]: 0 files, 1 directories
    flashfs[4]: 0 orphaned files, 0 orphaned directories
    flashfs[4]: Total bytes: 11999232
    flashfs[4]: Bytes used: 1024
    flashfs[4]: Bytes available: 11998208
    flashfs[4]: flashfs fsck took 0 seconds.
    flashfs[4]: Initialization complete.
    Copying radio files from flash: to ram:
    Copy in progress...CCCCC
    Copy in progress...CCC
    Copy in progress...CCCC
    Copy in progress...CCCC
    Copy in progress...CC
    Copy in progress...CCCC
    Copy in progress...CC
    Copy in progress...CCCCC
    Copy in progress...CCCC
    Copy in progress...CC
    Uncompressing radio files...
    ...done Initializing flashfs.
    Radio0  present 8764 8000 0 A8000000 A8010000 0
    Rate table has 650 entries (20 legacy/224 11n/406 11ac)
    POWER TABLE FILENAME = ram:/Q2.bin
    Radio1  present 8864 8000 0 80000000 80100000 4
    POWER TABLE FILENAME = ram:/Q5.bin
    Radio2 not present 0 0 0 0 0 8
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP3702I-Z-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
    Processor board ID FGL1838X4T1
    PowerPC CPU at 800Mhz, revision number 0x2151
    Last reset from power-on
    LWAPP image version 8.0.110.0
    1 Gigabit Ethernet interface
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: F4:4E:05:B7:1E:84
    Part Number                          : 73-15243-01
    PCA Assembly Number                  : 000-00000-00
    PCA Revision Number                  :
    PCB Serial Number                    : FOC18343WPR
    Top Assembly Part Number             : 068-05054-03
    Top Assembly Serial Number           : FGL1838X4T1
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP3702I-Z-K9
    % Please define a domain-name first.
    Press RETURN to get started!
    *Mar  1 00:00:19.295: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
    *Mar  1 00:00:19.755: Registering HW DTLS
    *Mar  1 00:00:19.763: APAVC: Initial WLAN Buffers Given to System is  2500
    *Mar  1 00:00:19.815: APAVC:  WlanPAKs 42878 RadioPaks  42270
    *Mar  1 00:00:22.127: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:26.055: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
    *Mar  1 00:00:26.167: Loading Power Tables from ram:/Q2.bin. Class = A
    *Mar  1 00:00:26.167:  record size of 3ss: 1168 read_ptr: 4F9698E
    *Mar  1 00:00:31.207: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
    *Mar  1 00:00:31.251: Loading Power Tables from ram:/Q5.bin. Class = Z
    *Mar  1 00:00:31.251:  record size of vht: 2904 read_ptr: 4F9698E
    *Mar  1 00:00:31.407: Wait until the stile protocol list is initialized.
    *Mar  1 00:00:32.651: Start STILE Activation
    *Mar  1 00:00:34.571: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
    *Mar  1 00:00:35.447: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 19-Dec-14 11:20 by prod_rel_team
    *Mar  1 00:00:35.447: %SNMP-5-COLDSTART: SNMP agent on host Test_1 is undergoing a cold start
    *Mar  1 00:00:36.563: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:37.787: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
    *Mar  1 00:00:37.939: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:37.939: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:00:47.567: %LINK-6-UPDOWN: Interface BVI1, changed state to down
    *Mar  1 00:00:48.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
    *Mar  1 00:00:50.431: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
    *Mar  1 00:00:50.431: DPAA Initialization Complete
    *Mar  1 00:00:50.431: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
    *Mar  1 00:00:51.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:53.435: %LINK-6-UPDOWN: Interface BVI1, changed state to up
    *Mar  1 00:00:53.867: Currently running a Release Image
    *Mar  1 00:00:54.287: Incorrect certificate in SHA2 PB !
    *Mar  1 00:00:54.287: Using SHA-1 signed certificate for image signing validation.
    *Mar  1 00:00:54.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:59.787: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.2, mask 255.255.255.0, hostname Test_1
    *Mar  1 00:01:02.707: APAVC: Succeeded to activate all the STILE protocols.
    *Mar  1 00:01:02.707: APAVC: Registering with CFT
    *Mar  1 00:01:02.707: APAVC: CFT registration of delete callback succeeded
    *Mar  1 00:01:02.707: APAVC: Reattaching  Original Buffer pool for system use
    *Mar  1 00:01:02.707: Pool-ReAtach: paks 42878 radio42270
    %Default route without gateway, if not a point-to-point interface, may impact performance
    *Mar  1 00:01:10.103: AP image integrity check PASSED
    *Mar  1 00:01:10.187: Incorrect certificate in SHA2 PB !
    *Mar  1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:01:11.591: %CDP_PD-4-POWER_OK: 15.4 W power - NEGOTIATED inline power source
    *Mar  1 00:01:12.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:01:13.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:01:13.947: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:01:14.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Mar  1 00:01:20.211: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:01:31.215: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
    *Mar  1 00:02:11.599: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Mar  1 00:02:11.603: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    *Mar  1 00:02:11.611: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:02:12.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:02:12.639: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:02:12.647: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Mar  1 00:02:12.655: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:02:13.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:02:13.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:02:13.699: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:02:14.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    Not in Bound state.
    *Mar  1 00:02:44.719: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
    *Mar  1 00:02:49.839: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.3, mask 255.255.255.0, hostname Test_1
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:02:55.719: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
    Not in Bound state.
    *Mar  1 00:03:59.219: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
    *Mar  1 00:04:04.343: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.4, mask 255.255.255.0, hostname Test_1
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:04:10.223: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP

  • 1242 is not joining controller

    hello friends,
    i have 1240 series access points which is not joining controller 5500 series..
    here is logs at joining time below
    AP503d.e56e.e7be#Xmodem file system is available.
    flashfs[0]: 7 files, 2 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 15998976
    flashfs[0]: Bytes used: 2649600
    flashfs[0]: Bytes available: 13349376
    flashfs[0]: flashfs fsck took 25 seconds.
    Base ethernet MAC Address: 50:3d:e5:6e:e7:be
    Initializing ethernet port 0...
    Reset ethernet port 0...
    Reset done!
    ethernet link up, 100 mbps, full-duplex
    Ethernet port 0 initialized: link is up
    button is pressed, wait for button to be released...
    button pressed for 37 seconds
    process_config_recovery: set IP address and config to default 10.0.0.1
    process_config_recovery: image recovery
    image_recovery: Download default IOS tar image tftp://255.255.255.255/c1240-k9w7-tar.default
    examining image...
    %Error opening  (connection timed out)Loading "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx"...#############################################################################################################################################
    File "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2009 by Cisco Systems, Inc.
    Compiled Mon 02-Nov-09 18:40 by prod_rel_team
    Proceeding with system init
    Proceeding to unmask interrupts
    Initializing flashfs...
    flashfs[1]: 6 files, 2 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 15998976
    flashfs[1]: Bytes used: 2632192
    flashfs[1]: Bytes available: 13366784
    flashfs[1]: flashfs fsck took 4 seconds.
    flashfs[1]: Initialization complete....done Initializing flashfs.
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-LAP1242AG-E-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
    Processor board ID FCZ150482DL
    PowerPCElvis CPU at 262Mhz, revision number 0x0950
    Last reset from power-on
    LWAPP image version 3.0.51.0
    1 FastEthernet interface
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 50:3D:E5:6E:E7:BE
    Part Number                          : 73-10256-07
    PCA Assembly Number                  : 800-26918-06
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC150158MH
    Top Assembly Part Number             : 800-29152-03
    Top Assembly Serial Number           : FCZ150482DL
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-LAP1242AG-E-K9
    % Please define a domain-name first.
    Press RETURN to get started!
    *Mar  1 00:00:05.426: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 34 messages)
    *Mar  1 00:00:07.500: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
    *Mar  1 00:00:07.526: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2009 by Cisco Systems, Inc.
    Compiled Mon 02-Nov-09 18:40 by prod_rel_team
    *Mar  1 00:00:07.601: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Mar  1 00:00:08.500: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
    *Mar  1 00:00:12.979: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
    AP503d.e56e.e7be#
    *Mar  1 00:00:46.445: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
    AP503d.e56e.e7be#
    AP503d.e56e.e7be#
    AP503d.e56e.e7be#sh ver
    Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2009 by Cisco Systems, Inc.
    Compiled Mon 02-Nov-09 18:40 by prod_rel_team
    ROM: Bootstrap program is C1240 boot loader
    BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
    AP503d.e56e.e7be uptime is 0 minutes
    System returned to ROM by power-on
    System image file is "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx"
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-LAP1242AG-E-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
    Processor board ID FCZ150482DL
    PowerPCElvis CPU at 262Mhz, revision number 0x0950
    Last reset from power-on
    LWAPP image version 3.0.51.0
    1 FastEthernet interface
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 50:3D:E5:6E:E7:BE
    Part Number                          : 73-10256-07
    PCA Assembly Number                  : 800-26918-06
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC150158MH
    Top Assembly Part Number             : 800-29152-03
    Top Assembly Serial Number           : FCZ150482DL
    --More--
    *Mar  1 00:00:56.445: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not haveTop Revision Number                  : A0
    Product/Model Number                 : AIR-LAP1242AG-E-K9
    Configuration register is 0xF
    AP503d.e56e.e7be#
    *Mar  1 00:01:06.445: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
    any advice please??
    thanks

    It sounds like you are still working out IP connectivity, but I also noticed your AP is not for US regulatory domain.
    Can you confirm that your WLC is ready to accept an AP with country code -E?
    Your AP model:  AIR-LAP1242AG-E-K9
    From the WLC CLI
    >show country
    If you are in US, you should only have -A available.  If this AP is intended to be used the US, then you will need to acquire an AP with the correct country code, as -E would not be supported in the US -A regulatory domain and should not be used.  Perhaps this is for another location, so you may need to add the applicable regulatory domain support.
    This link provides the list of the respective country codes and compatbility/etc.
    http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd80537b6a_ps6087_Products_Data_Sheet.html

  • AP 3702 not join the WLC

    Hi,
    I have two WLC 8500 working in SSO and with nat enable feature configure in management interface.
    SSO is working, but i have to configure NAT before SSO becasuse when SSO is up, ip address and nat are greyed out in managemente interface.
    Some AP's must join the controller in the private address of the management interface and others AP must join in the public ip address configured in NAT address. 
    for some reason, there are a lot of AP's that can't join the controller, i have 3 ap's joined in the public ip address and 3 ap's joined in the private ip address
    config network ap-discovery nat-only disable is already configured, from the console of one AP that can't not join i see the following:
    *Sep 10 12:32:48.115: %CAPWAP-3-ERRORLOG: Selected MWAR 'GI12WLC001A'(index 0).
    *Sep 10 12:32:48.115: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Sep 10 12:35:48.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 212.89.5.130 peer_port: 5246
    *Sep 10 12:36:17.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
    *Sep 10 12:36:47.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 212.89.5.130:5246
    *Sep 10 12:36:47.999: %CAPWAP-3-ERRORLOG: Selected MWAR 'GI12WLC001A'(index 0).
    *Sep 10 12:36:47.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Sep 10 12:35:48.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.35.0.78 peer_port: 5246
    the AP is trying both private and public ip address to join the WLC but can't join properly.
    From the WLC console:
    debug capwap errors enable:
    *spamApTask4: Sep 10 13:13:49.837: 00:10:db:ff:50:06 Discarding non-ClientHello Handshake OR DTLS encrypted packet from  10.35.1.13:47807)since DTLS session is not established 
    *spamApTask3: Sep 10 13:13:49.958: 1c:6a:7a:5b:e0:30 ApModel: AIR-CAP3702I-E-K9
    *spamApTask3: Sep 10 13:13:49.958: Unknown AP type. Using Controller Version!!!
    *spamApTask3: Sep 10 13:13:49.958: Unknown AP type. Using Controller Version!!!
    *spamApTask3: Sep 10 13:13:49.958: 1c:6a:7a:5b:e0:30 ApModel: AIR-CAP3702I-E-K9
    *spamApTask3: Sep 10 13:13:49.958: Unknown AP type. Using Controller Version!!!
    *spamApTask3: Sep 10 13:13:49.958: Unknown AP type. Using Controller Version!!!
    *spamApTask2: Sep 10 13:13:52.103: 00:10:db:ff:50:06 Discarding non-ClientHello Handshake OR DTLS encrypted packet from  10.35.1.11:21207)since DTLS session is not established 
    *spamApTask1: Sep 10 13:13:52.224: 1c:6a:7a:5e:0f:10 ApModel: AIR-CAP3702I-E-K9
    *spamApTask1: Sep 10 13:13:52.224: Unknown AP type. Using Controller Version!!!
    *spamApTask1: Sep 10 13:13:52.224: Unknown AP type. Using Controller Version!!!
    *spamApTask1: Sep 10 13:13:52.224: 1c:6a:7a:5e:0f:10 ApModel: AIR-CAP3702I-E-K9
    *spamApTask1: Sep 10 13:13:52.224: Unknown AP type. Using Controller Version!!!
    *spamApTask1: Sep 10 13:13:52.224: Unknown AP type. Using Controller Version!!!
    the AP model are the same, this is not the problem, but for some reason there are AP's that have problems with the NAT configuration, if i disable NAT option, every AP with private ip address config can join the WLC.
    I've tried to break SSO, desconfigure NAT, and private ip address AP join the controller without problem.
    anybody can give me a clue?
    Regards!

    it seens like DTLS connection can't be stablished between AP and WLC.
    The AP sends discovery request
    the WLC respond with two discovery responds, the firts one, contains the public ip address of the WLC and the second one contains the private ip address.
    once discovery proccess is complete, the AP tries to send DTLS hello packet to the WLC, but this packet never arrives to WLC.
    because hello doesn't arrive, the AP sends a close notify alert to the WLC and tries to send the DTLS hello packet to the WLC private address with same result.
    the AP get into a loop trying to send DTLS hello packets to both private and public address.
    DTLS hello packet never arrive, but close notify alert arrive to WLC.
    theres is FW in the middle doing NAT, but i can understand why close notify alert packets error arrives WLC and Hello DTLS packets don't. this packets uses the same protocol UDP and the same port.
    Regards

  • AP not joining

    Hi all,
    I could need a little help troubleshooting some AP issue.
    For some reason some AP will not join the WLC. (WISMII)
    I have several hundrede AP online, but still a few offline
    This fails:
    FRH-R06-L226-UX-G#sh cdp nei gi2/0/41 detail
    Device ID: AP5057.a8a1.c632
    Entry address(es):
      IP address: 10.61.24.103
    Platform: cisco AIR-CAP3502I-E-K9   ,  Capabilities: Trans-Bridge      (why only Trans-Bridge mode and not Capabilities: Router Trans-Bridge)
    Interface: GigabitEthernet2/0/41,  Port ID (outgoing port): GigabitEthernet0
    Holdtime : 161 sec
    Version :
    Cisco IOS Software, C3500 Software (AP3G1-RCVK9W8-M), Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)     (yes recovery image I know)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2011 by Cisco Systems, Inc.
    Compiled Tue 18-Oct-11 15:02 by prod_rel_team
    advertisement version: 2
    Duplex: full
    Power drawn: 14.500 Watts     (will it change when AP come online?)
    Power request id: 63919, Power management id: 2
    Power request levels are:14500 0 0 0 0
    Management address(es):
    This works fine:
    FRH-R06-L226-UX-G#sh cdp nei gi2/0/26 detail
    Device ID: AP442b.03c2.638d
    Entry address(es):
    IP address: 10.61.24.84
    Platform: cisco AIR-CAP3502I-E-K9   ,  Capabilities: Router Trans-Bridge
    Interface: GigabitEthernet2/0/26,  Port ID (outgoing port): GigabitEthernet0.1
    Holdtime : 128 sec
    Version :
    Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2012 by Cisco Systems, Inc.
    Compiled Mon 10-Dec-12 23:33 by prod_rel_team
    advertisement version: 2
    Duplex: full
    Power drawn: 15.400 Watts
    Power request id: 45452, Power management id: 2
    Power request levels are:15400 14500 0 0 0
    Management address(es):
    Switchport config:
    interface GigabitEthernet2/0/41
    description .1X XG-B-41
    switchport access vlan 552
    switchport mode access
    authentication control-direction in
    authentication event fail retry 0 action next-method
    authentication event server dead action authorize vlan 552
    authentication event server dead action authorize voice
    authentication host-mode multi-auth
    authentication order dot1x mab
    authentication priority dot1x mab
    authentication port-control auto
    authentication periodic
    authentication timer reauthenticate server
    mab
    dot1x pae authenticator
    dot1x timeout quiet-period 5
    dot1x timeout tx-period 3
    storm-control broadcast level 0.50
    storm-control multicast level 0.50
    storm-control action shutdown
    storm-control action trap
    spanning-tree portfast
    spanning-tree bpduguard enable
    end
    I have no access to the console interface on the AP at the moment.
    any suggestions
    /Finn

    Well you need to take a look at the AP or console. There have been issues with the 3500's and the white light of death. If you can have someone confirm if the APs led is white or not, that will tell you right away if you need to RMA the ap or not. Other than that, you need to console into the AP and post the output when powering up the AP.
    Sent from Cisco Technical Support iPhone App

  • APs not joining WLC

    Hello community,
    I hope you can help me with my problem.
    I have a vWLC Firmware version: 7.4.121.0, I have also Aironet 1700Aps
    I have successfully configured wlc with service and management interface. In the management network I can ping the vWLC managenemt interface as well the APs in this network. The firewall is also the DHCP Server for the management network. (It is working because APs get an IP address) The problem is the APs are not joining the vWLC. This is my first time I use WLC and APs. So they are completely new and not used before.
    Here is the debug output of vWLC:
    ApTask4: Feb 11 16:31:07.997: 84:80:2d:bd:fa:10 Finding DTLS connection to delete for AP (192:168:200:10/57250)
    *spamApTask4: Feb 11 16:31:07.997: 84:80:2d:bd:fa:10 Disconnecting DTLS Capwap-Ctrl session 0x8faa580 for AP (192:168:200:10/57250)
    *spamApTask4: Feb 11 16:31:07.997: 84:80:2d:bd:fa:10 CAPWAP State: Dtls tear down
    *spamApTask4: Feb 11 16:31:07.998: 84:80:2d:bd:fa:10 DTLS connection closed event receivedserver (192:168:200:3/5246) client (192:168:200:10/57250)
    *spamApTask4: Feb 11 16:31:07.998: 84:80:2d:bd:fa:10 Entry exists for AP (192:168:200:10/57250)
    *spamApTask4: Feb 11 16:31:07.998: 84:80:2d:bd:fa:10 No AP entry exist in temporary database for 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.004: 84:80:2d:bd:fa:1e DTLS connection not found, creating new connection for 192:168:200:10 (57250) 192:168:200:3 (5246)
    *spamApTask4: Feb 11 16:31:08.472: 84:80:2d:bd:fa:1e DTLS Session established server (192.168.200.3:5246), client (192.168.200.10:57250)
    *spamApTask4: Feb 11 16:31:08.472: 84:80:2d:bd:fa:1e Starting wait join timer for AP: 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.477: 84:80:2d:bd:fa:10 Join Request from 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.477: 84:80:2d:bd:fa:1e Deleting AP entry 192.168.200.10:57250 from temporary database.
    *spamApTask4: Feb 11 16:31:08.477: 84:80:2d:bd:fa:10 Finding DTLS connection to delete for AP (192:168:200:10/57250)
    *spamApTask4: Feb 11 16:31:08.477: 84:80:2d:bd:fa:10 Disconnecting DTLS Capwap-Ctrl session 0x8faa720 for AP (192:168:200:10/57250)
    *spamApTask4: Feb 11 16:31:08.477: 84:80:2d:bd:fa:10 CAPWAP State: Dtls tear down
    *spamApTask4: Feb 11 16:31:08.479: 84:80:2d:bd:fa:10 DTLS connection closed event receivedserver (192:168:200:3/5246) client (192:168:200:10/57250)
    *spamApTask4: Feb 11 16:31:08.479: 84:80:2d:bd:fa:10 Entry exists for AP (192:168:200:10/57250)
    *spamApTask4: Feb 11 16:31:08.479: 84:80:2d:bd:fa:10 No AP entry exist in temporary database for 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.515: 84:80:2d:bd:fa:10 Discovery Request from 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.515: 84:80:2d:bd:fa:10 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 200, joined Aps =0
    *spamApTask4: Feb 11 16:31:08.515: 84:80:2d:bd:fa:10 Discovery Response sent to 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.515: 84:80:2d:bd:fa:10 Discovery Response sent to 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.516: 84:80:2d:bd:fa:10 Discovery Request from 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.516: 84:80:2d:bd:fa:10 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 200, joined Aps =0
    *spamApTask4: Feb 11 16:31:08.516: 84:80:2d:bd:fa:10 Discovery Response sent to 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.516: 84:80:2d:bd:fa:10 Discovery Response sent to 192.168.200.10:57250
    *spamApTask0: Feb 11 16:31:08.516: 84:80:2d:bd:fa:1e Received LWAPP DISCOVERY REQUEST to 40:4a:03:79:d7:20 on port '1'
    *spamApTask0: Feb 11 16:31:08.516: 84:80:2d:bd:fa:1e Discarding discovery request in LWAPP from AP supporting CAPWAP
    Sadly I don`t have a debuging cable for the APs. Therefore I have no debuging output of the APs. (It is ordered ;-) )
    But I hope the output of the APs is right now not important to solve this problem.
    Thank you
    //EDIT
    On the firewall are no ports blocked

    Okay I upgraded the vWLC to 8.0.110.0.
    I looked in the event log of the vWLC. It was successfully discovered and also the new image version was send to the AP.
    Sadly the Ap does not join to the vWLC.
    *apfReceiveTask: Feb 12 09:53:35.640: WARP IEs: (12)
    *apfReceiveTask: Feb 12 09:53:35.640:      [0000] dd 0a 00 c0 b9 01 00 00 00 08 01 01
    *apfReceiveTask: Feb 12 09:53:35.640: Wlan Feature status 0 for  AP:84:80:2d:45:75:e0 (slotID 1)
    *apfReceiveTask: Feb 12 09:53:35.640: Split tunnel status (Disabled) encoded in the vap payload for WLAN(1), AP:84:80:2d:45:75:e0 (slotID 1)
    *spamApTask5: Feb 12 09:53:35.789: 84:80:2d:45:75:e0 Configuration Status from 192.168.200.10:57251
    *spamApTask5: Feb 12 09:53:35.789: 84:80:2d:45:75:e0 CAPWAP State: Configure
    *spamApTask5: Feb 12 09:53:35.789: 84:80:2d:45:75:e0 Updating IP info for AP 84:80:2d:45:75:e0 -- static 0, 192.168.200.10/255.255.255.0, gtw 192.168.200.3
    *spamApTask5: Feb 12 09:53:35.789: 84:80:2d:45:75:e0 Updating IP 192.168.200.10 ===> 192.168.200.10 for AP 84:80:2d:45:75:e0
    *spamApTask5: Feb 12 09:53:35.789: 84:80:2d:45:75:e0 Invalid length (9) countedlen 6 sizeUserPayload 277 for vendor-specific element 0x00409600-unknown (185) from AP  84:80:2D:45:75:E0
    *spamApTask5: Feb 12 09:53:35.790: 84:80:2d:45:75:e0 Setting MTU to 1485
    *spamApTask5: Feb 12 09:53:35.790: 84:80:2d:45:75:e0 Finding DTLS connection to delete for AP (192:168:200:10/57251)
    *spamApTask5: Feb 12 09:53:35.790: 84:80:2d:45:75:e0 Disconnecting DTLS Capwap-Ctrl session 0xb947000 for AP (192:168:200:10/57251)
    *spamApTask5: Feb 12 09:53:35.790: 84:80:2d:45:75:e0 CAPWAP State: Dtls tear down
    *spamApTask5: Feb 12 09:53:35.791: 84:80:2d:45:75:e0 DTLS connection closed event receivedserver (192.168.200.3/5246) client (192.168.200.10/57251)
    *spamApTask5: Feb 12 09:53:35.791: 84:80:2d:45:75:e0 Entry exists for AP (192.168.200.10/57251)
    *spamApTask5: Feb 12 09:53:35.791: 84:80:2d:45:75:e0 apfSpamProcessStateChangeInSpamContext: Deregister LWAPP event for AP 84:80:2d:45:75:e0 slot 0
    *spamApTask5: Feb 12 09:53:35.791: 84:80:2d:45:75:e0 apfSpamProcessStateChangeInSpamContext: Deregister LWAPP event for AP 84:80:2d:45:75:e0 slot 1
    *spamApTask5: Feb 12 09:53:35.791: update ap status:84:80:2d:45:75:e0 ,index:60
    *spamApTask5: Feb 12 09:53:35.791: 84:80:2d:45:75:e0 No AP entry exist in temporary database for 192.168.200.10:57251
    *apfReceiveTask: Feb 12 09:53:35.792: 84:80:2d:45:75:e0 Deregister LWAPP event for AP 84:80:2d:45:75:e0 slot 0
    *apfReceiveTask: Feb 12 09:53:35.792: 84:80:2d:45:75:e0 Deregister LWAPP event for AP 84:80:2d:45:75:e0 slot 1
    *spamApTask4: Feb 12 09:53:35.918: 84:80:2d:45:75:e0 Discovery Request from 192.168.200.10:57250
    *spamApTask4: Feb 12 09:53:35.918: 84:80:2d:45:75:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 200, joined Aps =0
    *spamApTask4: Feb 12 09:53:35.918: apModel: AIR-CAP702I-C-K9
    *spamApTask4: Feb 12 09:53:35.918: apType = 45 apModel: AIR-CAP702I-C-K9
    *spamApTask4: Feb 12 09:53:35.918: 84:80:2d:45:75:e0 Discovery Response sent to 192.168.200.10 port 57250
    *spamApTask4: Feb 12 09:53:35.918: 84:80:2d:45:75:e0 Discovery Response sent to 192.168.200.10:57250
    *spamApTask4: Feb 12 09:53:35.919: 84:80:2d:45:75:e0 Discovery Request from 192.168.200.10:57250
    *spamApTask4: Feb 12 09:53:35.919: 84:80:2d:45:75:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 200, joined Aps =0
    *spamApTask4: Feb 12 09:53:35.919: apModel: AIR-CAP702I-C-K9
    *spamApTask4: Feb 12 09:53:35.919: apType = 45 apModel: AIR-CAP702I-C-K9
    *spamApTask4: Feb 12 09:53:35.919: 84:80:2d:45:75:e0 Discovery Response sent to 192.168.200.10 port 57250
    *spamApTask4: Feb 12 09:53:35.919: 84:80:2d:45:75:e0 Discovery Response sent to 192.168.200.10:57250
    Sadly I don`t understand what this debugging log says :-(
    Maybe you can help me again
    Thank you
    //SOLUTION -----------------------------------------------------------------------------------------------------------------------------------------------------------
    I found something on the internet, but for all people having also this problem here is the solution:
    Change the country of your vWLC. Right now I am in China, so I changed it and then it was working flawlessly :-)
    Step 1  
    Disable the 802.11 networks as follows:
    Choose Wireless > 802.11a/n > Network.
    Unselect the 802.11a Network Status check box.
    Click Apply.
    Choose Wireless > 802.11a/n > Network.
    Unselect the 802.11b/g Network Status check box.
    Click Apply.
    Step 2  
    Choose Wireless > Country to open the Country page.
    Thank you all for your help :-)
    Paul

  • AP not joining WLC 2504

    Hi all
    my customer has a 2504 WLC, and has problems to join APs (There are no aps joined to the controller at this moment).
    What are the Bold lines tell me?
    in the debug I see the following:
    *spamApTask0: Oct 10 09:20:06.019: 58:f3:9c:78:d1:10 Discovery Request from 10.37.24.116:41508
    *spamApTask0: Oct 10 09:20:06.019: 58:f3:9c:78:d1:10 ApModel: AIR-CAP3702I-N-K9
    *spamApTask0: Oct 10 09:20:06.019: 58:f3:9c:78:d1:10 Join Priority Processing status = 0, Incoming Ap's Priority 4, MaxLrads = 50, 0
    *spamApTask0: Oct 10 09:20:06.019: apModel: AIR-CAP3702I-N-K9
    *spamApTask0: Oct 10 09:20:06.020: apType = 38 apModel: AIR-CAP3702I-N-K9
    *spamApTask0: Oct 10 09:20:06.020: Unknown AP type. Using Controller Version!!!
    *spamApTask0: Oct 10 09:20:06.020: 58:f3:9c:78:d1:10 Discovery Response sent to 10.37.24.116 port 41508
    *spamApTask0: Oct 10 09:20:06.020: 58:f3:9c:78:d1:10 Discovery Response sent to 10.37.24.116:41508
    *spamApTask0: Oct 10 09:20:06.021: 58:f3:9c:78:d1:10 Discovery Request from 10.37.24.116:41508
    *spamApTask0: Oct 10 09:20:06.021: 58:f3:9c:78:d1:10 ApModel: AIR-CAP3702I-N-K9
    *spamApTask0: Oct 10 09:20:06.021: 58:f3:9c:78:d1:10 Join Priority Processing status = 0, Incoming Ap's Priority 4, MaxLrads = 50, 0
    *spamApTask0: Oct 10 09:20:06.021: apModel: AIR-CAP3702I-N-K9
    *spamApTask0: Oct 10 09:20:06.021: apType = 38 apModel: AIR-CAP3702I-N-K9
    *spamApTask0: Oct 10 09:20:06.021: Unknown AP type. Using Controller Version!!!
    *spamApTask0: Oct 10 09:20:06.021: 58:f3:9c:78:d1:10 Discovery Response sent to 10.37.24.116 port 41508
    *spamApTask0: Oct 10 09:20:06.021: 58:f3:9c:78:d1:10 Discovery Response sent to 10.37.24.116:41508
    *spamApTask0: Oct 10 09:20:16.031: 58:f3:9c:7a:22:30 DTLS connection not found, creating new connection for 10:37:24:116 (41508) 10)
    *spamApTask0: Oct 10 09:20:16.498: acDtlsPlumbControlPlaneKeys: lrad:10.37.24.116(41508) mwar:10.37.24.11(5246)
    *spamApTask0: Oct 10 09:20:16.498: 58:f3:9c:7a:22:30 Allocated index from main list, Index: 55
    *spamApTask0: Oct 10 09:20:16.498: 58:f3:9c:7a:22:30 Using CipherSuite AES128-SHA
    *spamApTask0: Oct 10 09:20:16.499: 58:f3:9c:7a:22:30 DTLS keys for Control Plane are plumbed successfully for AP 10.37.24.116. Inde6
    *spamApTask1: Oct 10 09:20:16.499: 58:f3:9c:7a:22:30 DTLS Session established server (10.37.24.11:5246), client (10.37.24.116:41508)
    *spamApTask1: Oct 10 09:20:16.499: 58:f3:9c:7a:22:30 Starting wait join timer for AP: 10.37.24.116:41508
    *spamApTask0: Oct 10 09:20:16.517: 58:f3:9c:78:d1:10 Join Request from 10.37.24.116:41508
    *spamApTask0: Oct 10 09:20:16.517: 58:f3:9c:7a:22:30 Deleting AP entry 10.37.24.116:41508 from temporary database.
    *spamApTask0: Oct 10 09:20:16.518: 58:f3:9c:7a:22:30 spamProcessJoinRequest : RAP, Check MAC filter
    *spamApTask0: Oct 10 09:20:16.518: 58:f3:9c:78:d1:10 In AAA state 'Idle' for AP 58:f3:9c:78:d1:10
    *spamApTask0: Oct 10 09:20:16.518: 58:f3:9c:7a:22:30 Mesh AP username 58f39c7a2230.
    *spamApTask0: Oct 10 09:20:16.518: 58:f3:9c:78:d1:10 Join Request failed!
    *spamApTask0: Oct 10 09:20:16.518: 58:f3:9c:78:d1:10 State machine handler: Failed to process  msg type = 3 state = 0 from 10.37.248
    *spamApTask0: Oct 10 09:20:16.518: 58:f3:9c:7a:22:30 Failed to parse CAPWAP packet from 10.37.24.116:41508
    *spamApTask0: Oct 10 09:20:16.519: XóxÑ
    *spamApTask0: Oct 10 09:20:16.519: 58:f3:9c:78:d1:10 Finding DTLS connection to delete for AP (10:37:24:116/41508)
    *spamApTask0: Oct 10 09:20:16.519: 58:f3:9c:78:d1:10 Disconnecting DTLS Capwap-Ctrl session 0x179437d8 for AP (10:37:24:116/41508)
    *spamApTask0: Oct 10 09:20:16.519: 58:f3:9c:78:d1:10 CAPWAP State: Dtls tear down
    *spamApTask0: Oct 10 09:20:16.520: acDtlsPlumbControlPlaneKeys: lrad:10.37.24.116(41508) mwar:10.37.24.11(5246)
    *spamApTask0: Oct 10 09:20:16.520: 58:f3:9c:78:d1:10 DTLS keys for Control Plane deleted successfully for AP 10.37.24.116
    *spamApTask0: Oct 10 09:20:16.526: 58:f3:9c:78:d1:10 DTLS connection closed event receivedserver (10.37.24.11/5246) client (10.37.2)
    *spamApTask0: Oct 10 09:20:16.526: 58:f3:9c:78:d1:10

    Hi all, the AP was in Mesh (Bridge) mode and could not connect to the controller
    Ok, how to find out that a AP is in bridge mode, without a join (No Access to the AP).
    go to monitor > statistics > AP Join
    you will see the AP here that tries to connect (clear the list before)
    if the ethernet MAC Address is the same as the Base radio MAC, than the AP is in bridge mode.
    normally ( in local mode) the Ethernet MAC Address reflects the APname
    To allow the AP to join, add in the Authorization list the APName mac Address!
    See: http://supertekboy.com/2014/01/13/cisco-lightweight-access-point-will-not-join-to-a-wireless-lan-controller/
    The case is solved now.

  • AP 1552E NOT JOINING WLC 2504

    Hello,
    I am currently having issue relating to my AP not joining the WLC. Have made the WLC the internal DHCP server and the AP has picked an IP Address but the below is what i get from the AP:
    *Feb 14 22:48:56.707: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Feb 14 22:48:56.759: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Feb 14 22:48:56.783:  status of voice_diag_test from WLC is false
    *Feb 14 22:49:12.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
    *Feb 14 22:49:12.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Feb 14 22:49:12.663: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
    *Feb 14 22:49:12.663: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    *Feb 14 22:49:12.663: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *Feb 14 22:49:17.663: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    *Feb 14 22:49:17.663: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.1.2
    *Feb 14 22:49:17.663: %DTLS-5-PEER_DISCONNECT: Peer 192.168.1.2 has closed connection.
    *Feb 14 22:49:17.663: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.2:5246
    *Feb 14 22:49:12.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
    *Feb 14 22:49:12.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Feb 14 22:49:12.663: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
    *Feb 14 22:49:12.663: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    *Feb 14 22:49:12.663: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    % CDP is not supported on this interface, or for this encapsulation
    *Feb 14 22:49:17.663: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    *Feb 14 22:49:17.663: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.1.2
    *Feb 14 22:49:17.663: %DTLS-5-PEER_DISCONNECT: Peer 192.168.1.2 has closed connection.
    *Feb 14 22:49:17.663: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.2:5246
    *Feb 14 22:49:17.707: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Feb 14 22:49:17.707: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Feb 14 22:49:17.759: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Feb 14 22:49:17.783:  status of voice_diag_test from WLC is false
    *Feb 14 22:49:34.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
    *Feb 14 22:49:34.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Feb 14 22:49:34.663: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
    *Feb 14 22:49:34.663: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    *Feb 14 22:49:34.663: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *Feb 14 22:49:39.663: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    *Feb 14 22:49:39.663: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.1.2
    *Feb 14 22:49:39.663: %DTLS-5-PEER_DISCONNECT: Peer 192.168.1.2 has closed connection.
    *Feb 14 22:49:39.663: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.2:5246
    *Feb 14 22:49:34.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
    *Feb 14 22:49:34.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Feb 14 22:49:34.663: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
    *Feb 14 22:49:34.663: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    *Feb 14 22:49:34.663: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *Feb 14 22:49:38.591: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
    *Feb 14 22:49:38.591: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
    *Feb 14 22:49:38.591: %MESH-6-LINK_UPDOWN: Mesh station f029.29c2.effc link Down
    *Feb 14 22:49:39.663: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2

    Platform: AIR-CT2504-K9, Version :
    Manufacturer's Name: Cisco Systems Inc.  Product Name: Cisco Controller  Product Version: 7.0.220.0  RTOS Version: Erro  Bootloader Version: 1.0.18  Build Type: DATA + WPS
    Platform: cisco AIR-CAP1552E-E-K9  Version :
    Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)
    Proceeding with system init
    Proceeding to unmask interrupts
    Initializing flashfs...
    flashfs[1]: 22 files, 3 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 31610880
    flashfs[1]: Bytes used: 6631936
    flashfs[1]: Bytes available: 24978944
    flashfs[1]: flashfs fsck took 5 seconds.
    flashfs[1]: Initialization complete.
    flashfs[2]: 0 files, 1 directories
    flashfs[2]: 0 orphaned files, 0 orphaned directories
    flashfs[2]: Total bytes: 5806080
    flashfs[2]: Bytes used: 1024
    flashfs[2]: Bytes available: 5805056
    flashfs[2]: flashfs fsck took 1 seconds.
    flashfs[2]: Initialization complete....done Initializing flashfs.
    Warning:  the compile-time code checksum does not appear to be present.
    Radio0  present 8364B 8000 A8020000 0 A8030000 30
    Radio1  present 8364B 8000 B8020000 0 B8030000 13
    Radio2 not present 0 0 0 0 0 11
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    %Error opening flash:/c1520-rcvk9w8-mx/info (No such file or directory)cisco AIR-CAP1552E-E-K9    (PowerPC 8349) processor (revision A0) with 49142K/16384K bytes of memory.
    Processor board ID FCZ1718H01Y
    PowerPC 8349 CPU at 533Mhz, revision number 0x0031
    Last reset from power loss
    LWAPP image version 7.0.220.0
    4 Gigabit Ethernet interfaces
    2 802.11 Radio(s)
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: F0:29:29:C2:EF:E0
    Part Number                          : 73-13538-02
    PCA Assembly Number                  : 800-31224-01
    PCA Revision Number                  : 03
    PCB Serial Number                    : FOC1705241P
    Top Assembly Part Number             : 800-34853-05
    Top Assembly Serial Number           : FCZ1718H01Y
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP1552E-E-K9
    % Please define a domain-name first.
    Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
    Press RETURN to get started!
    *Mar  1 00:00:07.307: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:07.723: m8349_ether_enable: MACCFG1 sync timeout
    *Mar  1 00:00:09.819: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:09.819: %LINK-3-UPDOWN: Interface Ethernet4, changed state to up
    *Mar  1 00:00:09.819: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:09.819: %LINK-3-UPDOWN: Interface GigabitEthernet1, changed state to up
    *Mar  1 00:00:09.819: %LINK-3-UPDOWN: Interface GigabitEthernet2, changed state to up
    *Mar  1 00:00:09.819: %LINK-3-UPDOWN: Interface GigabitEthernet3, changed state to up
    *Mar  1 00:00:11.375: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
    *Mar  1 00:00:11.375: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down
    *Mar  1 00:00:11.375: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2, changed state to down
    *Mar  1 00:00:11.375: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3, changed state to down
    *Mar  1 00:00:11.963: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
    *Mar  1 00:00:12.039: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)
    *Mar  1 00:00:12.051: AP identified to be in Fenway/Huck Jr/1240/1130 configuration
    *Mar  1 00:00:12.055:  status of voice_diag_test from WLC is false
    *Mar  1 00:00:14.079: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2011 by Cisco Systems, Inc.
    Compiled Tue 18-Oct-11 15:13 by prod_rel_team
    *Mar  1 00:00:14.079: %SNMP-5-COLDSTART: SNMP agent on host APf029.29c2.efe0 is undergoing a cold start
    *Mar  1 00:00:14.143: %MESH-6-BVI_CREATED: Mesh BVI1 interface created
    *Mar  1 00:00:14.163: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:00:14.163: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:00:15.163: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:00:15.163: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:16.143: %LINK-3-UPDOWN: Interface BVI1, changed state to down
    *Mar  1 00:00:17.139: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitE
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)thernet0, changed state to down
    *Mar  1 00:00:17.143: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down
    *Mar  1 00:00:17.143: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2, changed state to down
    *Mar  1 00:00:17.143: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3, changed state to down
    *Mar  1 00:00:18.579: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up
    *Mar  1 00:00:20.723: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:32.743: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Mar  1 00:00:32.795: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Mar  1 00:00:32.959: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:33.107: Logging LWAPP message to 255.255.255.255.
    *Mar  1 00:00:33.307: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
    *Mar  1 00:00:46.383: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C2960-24PC-S (189c.5d95.2d18)
    Username:
    *Mar  1 00:01:27.119: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
    Username:
    *Mar  1 00:01:32.163: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:01:34.119: %LINK-3-UPDOWN: Interface BVI1, changed state to up
    *Mar  1 00:01:35.119: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:01:37.207: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    % CDP is not supported on this interface, or for this encapsulation
    *Mar  1 00:01:40.887: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Mar  1 00:01:40.907:  status of voice_diag_test from WLC is false
    *Mar  1 00:01:46.387: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C2960-24PC-S (189c.5d95.2d18)
    Regards,
    Obinna Samuel

  • Cisco LAP 2602 can not join Virtual WLC

    dear all, 
    i just install Virtual WLC and i remove WLC 2504 , i install & configured it , but LAP can not join. it was work fine with WLC 2504.
    i used the same network topology with the old WLC.
    i receive this error logs.
    *spamApTask4: Feb 04 06:01:30.082: <<<<  Start of CAPWAP Packet  >>>>
    *spamApTask4: Feb 04 06:01:30.082: CAPWAP Control mesg Recd from 10.192.200.93, Port 26711
    *spamApTask4: Feb 04 06:01:30.082:              HLEN 4,   Radio ID 0,    WBID 1
    *spamApTask4: Feb 04 06:01:30.082:              Msg Type   :   CAPWAP_DISCOVERY_REQUEST
    *spamApTask4: Feb 04 06:01:30.082:              Msg Length : 155
    *spamApTask4: Feb 04 06:01:30.082:              Msg SeqNum : 0
    *spamApTask4: Feb 04 06:01:30.082:   
    *spamApTask4: Feb 04 06:01:30.082:       Type : CAPWAP_MSGELE_DISCOVERY_TYPE, Length 1
    *spamApTask4: Feb 04 06:01:30.082:              Discovery Type : CAPWAP_DISCOVERY_TYPE_UNKNOWN
    *spamApTask4: Feb 04 06:01:30.082:   
    *spamApTask4: Feb 04 06:01:30.082:       Type : CAPWAP_MSGELE_WTP_BOARD_DATA, Length 62
    *spamApTask4: Feb 04 06:01:30.083:              Vendor Identifier      : 0x00409600
    *spamApTask4: Feb 04 06:01:30.083:              WTP_SERIAL_NUMBER : AIR-CAP2602E-I-K9
    *spamApTask4: Feb 04 06:01:30.083:   
    *spamApTask4: Feb 04 06:01:30.083:       Type : CAPWAP_MSGELE_WTP_DESCRIPTOR, Length 40
    *spamApTask4: Feb 04 06:01:30.083:              Maximum Radios Supported  : 2
    *spamApTask4: Feb 04 06:01:30.083:              Radios in Use             : 2
    *spamApTask4: Feb 04 06:01:30.083:              Encryption Capabilities   : 0x00 0x01
    *spamApTask4: Feb 04 06:01:30.083:   
    *spamApTask4: Feb 04 06:01:30.083:       Type : CAPWAP_MSGELE_WTP_FRAME_TUNNEL, Length 1
    *spamApTask4: Feb 04 06:01:30.083:              WTP Frame Tunnel Mode : NATIVE_FRAME_TUNNEL_MODE
    *spamApTask4: Feb 04 06:01:30.083:   
    *spamApTask4: Feb 04 06:01:30.083:       Type : CAPWAP_MSGELE_WTP_MAC_TYPE, Length 1
    *spamApTask4: Feb 04 06:01:30.083:              WTP Mac Type  : SPLIT_MAC
    *spamApTask4: Feb 04 06:01:30.083:   
    *spamApTask4: Feb 04 06:01:30.083:       Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
    *spamApTask4: Feb 04 06:01:30.083:              Vendor Identifier  : 0x00409600
    *spamApTask4: Feb 04 06:01:30.083: 
            IE            :   UNKNOWN IE 207
    *spamApTask4: Feb 04 06:01:30.083:      IE Length     :   4
    *spamApTask4: Feb 04 06:01:30.083:      Decode routine not available, Printing Hex Dump
    *spamApTask4: Feb 04 06:01:30.083: 00000000: 03 00 00 01                                       ....
    *spamApTask4: Feb 04 06:01:30.083:   
    *spamApTask4: Feb 04 06:01:30.083:       Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 12
    *spamApTask4: Feb 04 06:01:30.083:              Vendor Identifier  : 0x00409600
    *spamApTask4: Feb 04 06:01:30.083: 
            IE            :   RAD_NAME_PAYLOAD
    *spamApTask4: Feb 04 06:01:30.083:      IE Length     :   6
    *spamApTask4: Feb 04 06:01:30.083:      Rad  Name     :   
    *spamApTask4: Feb 04 06:01:30.083: CEO_AP
    *spamApTask4: Feb 04 06:01:30.083: <<<<  End of CAPWAP Packet  >>>>
    *spamApTask4: Feb 04 06:01:30.083: dc:a5:f4:8c:ff:30 Discovery Request from 10.192.200.93:26711
    *spamApTask4: Feb 04 06:01:30.083: dc:a5:f4:8c:ff:30 ApModel: AIR-CAP2602E-I-K9
    *spamApTask4: Feb 04 06:01:30.083: dc:a5:f4:8c:ff:30 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 200, joined Aps =0
    *spamApTask4: Feb 04 06:01:30.083: apModel: AIR-CAP2602E-I-K9
    *spamApTask4: Feb 04 06:01:30.083: apType = 26 apModel: AIR-CAP2602E-I-K9
    *spamApTask4: Feb 04 06:01:30.083: apType: Ox1a bundleApImageVer: 8.0.110.0
    *spamApTask4: Feb 04 06:01:30.083: version:8 release:0 maint:110 build:0
    *spamApTask4: Feb 04 06:01:30.083: dc:a5:f4:8c:ff:30 Discovery Response sent to 10.192.200.93 port 26711
    *spamApTask4: Feb 04 06:01:30.083: dc:a5:f4:8c:ff:30 Discovery Response sent to 10.192.200.93:26711
    Please any help.

    dear
    yes  the wlc  2504  is 8.0.110 but because its damaged i replaced it with  new vWLC v 8.0.110.
    also i can not put the LAP in flexconnect until its joint.

Maybe you are looking for

  • Type def boolean button.

    hi, i'm korean. my english is it' too bad. that why i'm sorry. first i wanna make type def boolean button. it's not problem. but make triangle shape. happen problem. like that red box is notihing. but if i click there, that is change to true or false

  • Cost Center in populating in GR/IR Clearing Account at MIRO Posting

    Hi, I am working in 4.7 EE version. We created one Service Order(purchase order) and gave account assignment as Cost Center and Business area. Then we created service entry sheet wrt to service order and accepted the service enry sheet. System automa

  • Is it possible to update (=change) control block items in a query only form ?

    From Form.A we call Form.B with the parameter query_mode = query_only. This works fine. But in Form.B we have a non table block (=control block) with an poplist item. Allthough in query_only mode we like to change (it's not a real update cause it's c

  • Mighty Mouse will scroll down but not up.

    All of a sudden my mighty mouse won't scroll up. It will scroll down, left and right but not up. The mighty mouse is about 6 months old and has worked fine on my old Dual 1GHz G4 MDD.

  • I cannot view video in the viewer, canvas nor preview

    HELP! I already threw away my old FCP and QUICKTIME Preferences. I just downloaded the updates. HELP. I originally had FCP 4.5 and upgraded to the FCP Production Suite 5.0