Aironet 1100 Ping issues poor connectivity LAN

I have setup an Aironet 1100 on our old office, and we never had any connectivity issues.
A month ago we moved to a new location, some new equipment and i moved the Aironet to the new office.
The problem i am experiencing right now is packets drops. The AP is connected straight to out Poe switch. If i telnet into the switch and do an extended ping command, i can see a lot of packets dropping. I've check the interface duplex - speed and everything looks just fine. I have not change any settings on the AP since i moved it to the new location.
What else can i troubleshoot?
Thanks
Zeek

1) Did you try rebooting the AP?
2) Which switch model is it?
3) How is the switch port connecting the AP configured, trunk or access? If trunk how many VLANs are allowed?
4) Check the CPU/Memory on the AP, how much is it?
5) How many clients are connected at once?
Regards
Farrukh

Similar Messages

  • Aironet 1100 as repeater: radio disabled!?!

    I followed the directions according to the configuration guide 12.3(8)JA but the repeater never connects to the root AP and I notice the radio is "disabled" after setting the AP in repeater mode and it will not let me enable it. Any ideas as to why I cannot get the two Aironet 1100 AP's to connect and why the radio would be "disabled"?
    Thanks

    I have no security in place and the SSID are the exact same. I have the AP's about 15 ft apart so the coverage should be fine. The parent mac address is correct. Any other ideas? Thanks in advance.

  • Aironet 1100 dropping connection

    M.D. office using several Aironet 1100 mounted on wall in hallways outside exam rooms. Using Motion tablet PC's LE1600 Connection is "dropped" or Lost when moving tablet from room to room. IT guy has reset "switches" channels etc but nothing seem to work. Added more WAp's still have dead zones. Any suggestion?

    Here is the some steps which will help you to resolve the issue.
    Set the data rates to 'Best range'.
    Recommended to set the APs to non-overlapping channels.
    Suggested to reduce the size of the cell by changing the power settings.
    Here is the URL for the troubleshooting and administration for the AP. It may help you
    http://www.cisco.com/en/US/docs/wireless/access_point/12.3_4_JA/configuration/guide/s34trb.html

  • Linux clients not associating with Aironet 1100

    Does anyone know if there is an issue with a Linux client associating with an Aironet 1100 using WEP? Windows clients are connecting fine, and the Linux client connects to Linksys branded APs with WEP no problem.
    Aironet config:
    IOS 12.3(2)
    16 AP on same SSID, different cells
    128-bit WEP
    Linux client:
    Dlink Airplus DWL-G630
    Kernel: Slackware 2.6.12.2
    Commands used to associate
    ifconfig ath0 up
    iwconfig ath0 ath0 mode managed key restricted [2] {key}
    dhcpcd ath0
    After bringing up the ath0 interface, and running the iwconfig, you can see the iwconfig settings are sticking, but it seems to be jumping around APs when you watch the MAC of the AP. It goes from a valid MAC address to FF:FF:FF:FF:FF:FF and then to another valid address, and back again. This does not happen on the Linksys AP.
    Any ideas?
    Thanks,
    Andy

    Try entering the key (on the Linux box) as hex.
    Most of the Windows client software lets you enter the key in ASCII ... some client software requires that you put in the hex translation.
    You can check the logs on the 1100 to see what the failure message is ,,, but I'd bet it'll be something along the lines of "Invalid Key"
    Good Luck
    Scott

  • Aironet 1100 won't show IP Addr. w/ IPSU

    I am trying to set up a Aironet 1100. I enter the mac addr. into the IPSU and get a error - device does not answer. I've reset the device, ng. Tried 2 different computers, ng. I cannot get to the config. page. Any ideas?

    Plan B: Get yourself a copy of tftpd from here:
    http://tftpd32.jounin.net/
    A very lightweight TFTP & DHCP server (amongst other things). Install on a PC and connect to the new AP with a cross lead (or in such a way that the PC and AP are isolated from the main LAN). Start TFTPD and configure a DHCP scope, power on the AP and watch the TFTPD log screen. Connect to the AP with a browser and give it a static address on the main LAN.
    Plan C: Connect a console cable to the AP and reboot it, watch the boot process carefully and you'll see the IP address it leases.

  • Issue JDBC connection pool with Glassfish 3.1.2.2 and Oracle XE 11gR2

    Hello,
    I am experiencing an issue with pinging a JDBC connection Pool.
    I installed the following without any warnings or errors:
    Operating System: Oracle Enterprise Linux 5
    Oracle XE 11gR2 (11.2.0.2.0) database
    Glassfish 3.1.2.2
    I will refer to the steps I did after the installations
    1) In the .profile file of the OS I add the following:
    JRE_HOME=/usr/java/jre1.6.0_31; export JRE_HOME
    JAVA_HOME=/usr/java/jdk1.6.0_31; export JAVA_HOME
    GLASSFISH_DIR=/u01/glassfish3
    GLASSFISH_HOME=/u01/glassfish3/glassfish
    DERBY_HOME=$GLASSFISH_DIR/javadb
    OPEN_MQ_HOME=$GLASSFISH_DIR/mq
    PATH=:$JAVA_HOME/bin:$JRE_HOME/bin:$PATH:$HOME/bin:$GLASSFISH_HOME/bin:$DERBY_HOME/bin:$OPEN_MQ_HOME/bin
    export GLASSFISH_HOME
    export DERBY_HOME
    export OPEN_MQ_HOME
    export PATH
    LD_LIBRARY_PATH=/u01/app/oracle/product/11.2.0/xe/lib; export LD_LIBRARY_PATH
    . /u01/app/oracle/product/11.2.0/xe/bin/oracle_env.sh
    2) I copied the ojdbc6.jar to the $GLASSFISH_HOME/domains/domain1/lib
    3) I login to the Glassfish admin console and created a new JDBC Connection Pool.
    Pool Name: ds_orasys
    Resource Type: javax.sql.DataSource
    Datasource Classname: oracle.jdbc.pool.OracleDataSource
    User: [myschema]
    Password: [myschema password]
    URL: jdbc:oracle:thin:@localhost:1521:xe
    When I ping the connection pool I get the following message in the server log:
    [#|2012-10-23T12:14:37.069+0300|WARNING|glassfish3.1.2|javax.enterprise.resource.resourceadapter.com.sun.enterprise.connectors.service|_ThreadID=22;_ThreadName=Thread-2;|RAR8054: Exception while creating an unpooled [test] connection for pool [ ds_orasys ], Connection could not be allocated because: Invalid Oracle URL specified|#]
    [#|2012-10-23T12:14:37.071+0300|SEVERE|glassfish3.1.2|org.glassfish.admingui|_ThreadID=19;_ThreadName=Thread-2;|RestResponse.getResponse() gives FAILURE. endpoint = 'http://212.205.62.217:4848/management/domain/resources/ping-connection-pool.json'; attrs = '{id=ds_orasys}'|#]
    I tried to use different jar files. I used ojdbc6dms.jar and ojdbc14.jar.
    I also copied the jar files in the $GLASSFISH_HOME/domains/domain1/lib/ext directory as some people suggested. Still no luck. I keep getting the same error messages in the server.log
    Can anybody help me out or point me to the right direction.
    Thank you in advance

    The error is in the URL. It was in front of my eyes and I couldn't see the error. I skipped the ':' before the '@' when I created the pool. It is working fine now.

  • Event log errors after upgrading Aironet 1100

    We have upgraded an Aironet 1100 to 12.3(8)JA. We used TFTP for the upgrade and everything seems to be working properly.
    However, the event log shows the following message every four seconds: "System running-config write error; configuration failed" This has Error as the severity.
    Every thirty minutes another, Critical error is logged "Memory allocation of 900000 bytes failed from 0x22DC78, alignment 0"
    I've searched the site and can't seem to locate applicable information on these errors and what they mean. Can someone help?
    Thanks!

    Oddly enough, this is the most stable AP we have! A PDA can connect to it and stay connnected, whereas our other 1100s (which have not been upgraded and generate the same error messages but only once or twice a day)will permit a device to connect then boot it off after a few seconds to several minutes. We thought the upgrade would make the AP connections more stable but were surprised to see the error messages being generated so rapidly.

  • TS1398 Why does my ipad keep saying poor connection on FaceTime ever since ios6

    Why does my ipad keep saying poor connection on FaceTime since we went on ios6

    I have the same problem with my ipad 2.. ever since i updated to ios 6 it says "connecting" and never connects..and then 5  mins later it says "connection lost" CALL BACK! its so frustrating as i have not had any issue before the update..
    both me and the end caller have updated to ios 6, so im afraid the above response doesnt work for me! Some one please help, as its driving me nuts to not able to facetime!

  • Ping issues on 80Mb Inifinity

    Hello!
    So I'm getting an unsual ping issue. It's repeatable on all of my computers whether wireless or through ethernet/powerline, and I can only describe it as hangs in the traffic, where the entire connection will lock up for 500ms-2000ms and cause extreme issues while gaming. I'm attaching a ping test though which I have been using to monitor the issue, and that's done through a simple "ping www.google.co.uk -t" command in cmd.
    My pings are fantastic for a BT connection, except when this is happening. This is better than any ping I got with Virgin. I just wish I could get this resolved. I think because I'm using fibre that I am missing all of the ADSL information that's been posted around here. My router home page shows no power levels etc.

    I would just like to add to this, I am suffering exactly the same problems.
    Homehub5, tried wired pc, wireless laptop, and doen ping tests on 2 tablets
    UK Server    Minimum = 19ms, Maximum = 3166ms, Average = 132ms
    BBC.co.uk    Minimum = 19ms, Maximum = 3148ms, Average = 78ms
    ping.sunet.se    Minimum = 57ms, Maximum = 3477ms, Average = 179ms
    google.co.uk    Minimum = 18ms, Maximum = 3249ms, Average = 109ms
    it's all the time, not just at a specific time either.
    This problem affects any online gaming to the point the games are completely unplayable.
    Speaking with support yesterday, they informed me that the game servers website cache information was wrong and "we have fixed that now because we are able to"
    I'm a community moderator for EA Battlelog, and I know for a fact BT do not have access to the EA backend.

  • Aironet 1100 Default Username and Password not working

    I have a Cisco Aironet 1100 series access point (AP1120B) that after resetting to factory defaults the default username and password (Cisco and Cisco) aren't working in the web GUI.  I am able to telnet to the AP's IP and log in with Cisco and Cisco but don't know the ENABLE password. I have tried Cisco and cisco and everything else i could think of with no luck.  any help would be appreciated. 
    I also have a Cisco Aironet AP1242AG that is doing the same thing.

    Hi Rich,
    I assume that you are using the mode button to reset the configurations on these units -- this procedure *should* reset all credentials to Cisco.
    If this is still not working, you can try the following:
    1) Connect console port and power-cycle unit
    2) When IOS starts loading, hit ESC key twice to get to the boot-loader prompt
    3) At the boot-loader prompt show a directory of the flash filesystem (dir  flash:)
    4) Delete or rename the files "config.txt" and "env_vars", then boot  the  system ("delete flash:/config.txt" "delete flash:/env_vars")
    -Patrick Croak
    Wireless TAC

  • No IP address on Aironet 1100 AP

    We have 5 Aironet 1100 series APs deployed in one of our buildings. A few days ago, 3 of them showed down in our monitoring. The next day the other 2 showed down. When I go to the switches that they are attached to and do a show cdp neighbor detail, I see all the access points but NO IP address. Also, when I went to to site, I can connect to the APs via wireless and be on the network just fine. We have static IP addresses assigned to them. However, they are not pingable and do not show up in the ARP table of the switch.
    They have been running a couple of years without changes.
    Any ideas?
    Thanks
    Carl

    Probably a dumb question but have you rebooted the AP's? Also, are they drawing power from a powered switch or do they have their own mains power bricks attached?

  • Poor connectivity 3gs

    Continual poor connectivity / drop outs with my iphone 3gs. At my wits end . I've done all Vodaphone have advised, restored, disabled- reanabled 3g changed SIm etc etc, They now sent another phone, just the same. There is a Facebook site dedicated to this problem, apparently it might be a software issue but Vodaphone are not admitting this. A Galaxy used side by side with it on Vodaphone has no issues at all ( its just not an iphone!!!!). Any suggestions? Do Apple care about this? I may have to desert the brand as I run a business  and need an efficient smartphone. Just thought I'd post on here before giving up, any suggestions?
    Operating System 4.3.3

    Continual poor connectivity / drop outs with my iphone 3gs. At my wits end . I've done all Vodaphone have advised, restored, disabled- reanabled 3g changed SIm etc etc, They now sent another phone, just the same. There is a Facebook site dedicated to this problem, apparently it might be a software issue but Vodaphone are not admitting this. A Galaxy used side by side with it on Vodaphone has no issues at all ( its just not an iphone!!!!). Any suggestions? Do Apple care about this? I may have to desert the brand as I run a business  and need an efficient smartphone. Just thought I'd post on here before giving up, any suggestions?
    Operating System 4.3.3

  • Why do I get a "poor connection" error every time I try to use FaceTime on my new router

    I Have a new router, now every time I try to use facetime I get "poor connection" error. Can anyone help?

    Did you already check this article?
    iOS: Recommended settings for Wi-Fi routers and access points
    More things to try:
    Wi-Fi network issues
    Make sure that your Wi-Fi network is set up using the recommended settings for Wi-Fi routers and access points.
    If you encounter issues using a Wi-Fi network, use standard Wi-Fi network troubleshooting to resolve interference and other issues.
    If you're using router, firewall, or security software that restricts Internet access, make sure that the ports documented in Using FaceTime behind a Firewall are open.
    FaceTime requires a broadband connection. Performance might vary according to network throughput and usage.
    copied from iOS: Troubleshooting FaceTime

  • TS1398 poor connection on facetime

    Hi, my name is Brenda Mares. I'am having trouble using Facetime on my IPAD 4. Everytime someone calls me on Facetime or if I want to talk to someone on Facetime. I get Poor Connection. Please help me solve this problem.

    I have the same problem with my ipad 2.. ever since i updated to ios 6 it says "connecting" and never connects..and then 5  mins later it says "connection lost" CALL BACK! its so frustrating as i have not had any issue before the update..
    both me and the end caller have updated to ios 6, so im afraid the above response doesnt work for me! Some one please help, as its driving me nuts to not able to facetime!

  • Intermittent high ping issues

    I've been having occasional high ping issues for quite a while now. They come and go at irregular times, and I'm not sure how to resolve this. Other computers on the network are showing similar latency.
    A traceroute to google's public DNS:
    Traceroute to (8.8.8.8)
    1 L100.LSANCA-DSL-23.verizon-gni.net (71.104.144.1) 1644 ms 1088 ms 1346 ms
    2 G10-2-2823.LSANCA-LCR-08.verizon-gni.net (130.81.45.208) 886 ms 1118 ms 716 ms
    3 so-7-0-1-0.LAX01-BB-RTR2.verizon-gni.net (130.81.29.142) 1352 ms 1096 ms 1366 ms
    4 0.so-2-2-0.XL4.LAX15.ALTER.NET (152.63.10.121) 1026 ms 1432 ms 1246 ms
    5 0.so-1-0-0.XT2.NYC4.ALTER.NET (152.63.64.126) 550 ms 792 ms 590 ms
    6 TenGigE0-7-0-0.GW8.NYC4.ALTER.NET (152.63.22.45) 846 ms 884 ms 312 ms
    7 Internet-gw.customer.alter.net (152.179.72.66) 134 ms 180 ms 444 ms
    8 * (72.14.238.232) 274 ms 94 ms 712 ms
    9 * (209.85.252.2) 530 ms 1114 ms 1276 ms
    10 * (72.14.239.93) 1294 ms 1406 ms 1418 ms
    11 * (72.14.236.200) 1586 ms 690 ms 106 ms
    12 * (216.239.49.145) 106 ms 108 ms 354 ms
    13 google-public-dns-a.google.com (8.8.8.8) 296 ms 104 ms 148 ms
    Transceiver statistics:
    Transceiver Revision:
    7.2.3.0
    Vendor ID Code:
    4
    Line Mode:
    G.DMT Mode
    Data Path:
    Interleaved
    Transceiver Information
    Downstream Path
    Upstream Path
    DSL Speed (Kbits/Sec)
    3360
    736
    Margin (dB)
    13.5
    10.0
    Line Attenuation (dB)
    55.0
    31.0
    Transmit Power (dBm)
    17.8
    11.8

    #1 Visit http://www.giganews.com/line_info.html and post up the Traceroute the page shows, if you wish. Be aware that the final hop (bottom-most line of the trace) will contain a hop with your IP address in it. Remove that line. What I'm looking for is a line that mentions "ERX" in it's name towards the end. If for some reason the trace does not complete (two lines full of Stars), keep the trace route intact.
    #2 Have you tried connecting your modem to the NID ?
    I point to http://www.dslreports.com/faq/1317
    #3 What is the brand and model of this DSL modem?
    #4 If you have a RJ-45 WAN port router: What is the brand and model of it?
    If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

Maybe you are looking for