AirPort doesn't work after Leopard install

I have an iMac 20" 2GHz Core 2 Duo and my AirPort doesn't work. I reset my PRAM, erased the hard drive and installed a clean copy of Leopard after picking it up from the Retail store. I had exactly the same problem with 9A559 and the seed update and I ASSUMED it would be fixed by the time the final release is out. It doesn't detect any networks, even if i move the access point very close to the computer. I tried disabling all security on the access point. Tried changing channels. Tried resetting the access point to defaults and reconfiguring from scratch. Tried manually putting the SSID in on the iMac but none of it worked. The access point is a Linksys WAG54G with the latest firmware. If anyone can help me, please do because the AirPort is the ONLY way this computer can access the internet.

Just to clarify my situation:
Erase and install of Leopard
Airport card is detected:
Wireless Card Type: AirPort Extreme (0x14E4, 0x89)
Wireless Card Locale: Worldwide
Wireless Card Firmware Version: Broadcom BCM43xx 1.0 (4.170.25.10)
Current Wireless Network: wireless network not available
No networks are available for selection, (i can normally see 4 or 5)
System.log has:
Oct 27 00:07:04 my-names-imac SystemUIServer95: Error: Apple80211Scan() error 16
Oct 27 00:07:04 my-names-imac SystemUIServer95: Error: __performScan() failed, entering fail-save workaround..
Oct 27 00:07:07 my-names-imac SystemUIServer95: Error: Apple80211Scan() error -6
Oct 27 00:07:07 my-names-imac SystemUIServer95: Error: __performScan() failed (-6)
Oct 27 00:07:14 my-names-imac SystemUIServer95: Error: Apple80211Scan() error -6
I'm about two feet from my wireless router, none of the other (Tiger) computers have issues connecting to it.
Anyone else see the Apple80211Scan entries?

Similar Messages

Airport doesn't work after RAM install

I upgraded RAM on my Mac Mini. Followed directions and all is good. Mini with new RAM is running great; however now, my Airport doesn't see my or any neighborhood networks. Prior to the install this was all working fine.
I can' figure out the problem. Any suggestions on what to do?

Excellent! That was it. Thank you.
And notes from a novice: For those looking to upgrade RAM in the Mac mini (Intel) there are 3 things to note when pulling out the internal frame: 1. The little black (thermostat fan) cable up front. You must unhook but if you forget to reconnect the fan runs all the time. Not good; 2. The gold (audio) band in the back. This too came off very easily. Very small (plastic) clamp that was tedioius to set back. Lift internal frame and turn like a book page; and 3. the airport cable. There are 2 small circular (beige color) ports. Use the MAIN (it's in tiny print) near the back.

Sound doesn't work after Leopard install

I installed Leopard last night, on my G4 Mirror-door, which is a twin 1.25GB with 4Gb RAM. Now, I am unable to get sound out of my subwoofer (the transparent USB that came with my Cube) or my speakers (Bose with RCA plug).
I was trying to listen to a podcast, and initially I got normal sound, then it became intermittent, then it stopped. The System Preferences look normal, and the volume is definitely turned up in iTunes, the menu bar, and on the speakers.
It looked a little like the problem might be iTunes, since neither podcasts nor music shows any activity in the progress bar. However, Real Player doesn't make sound, either.
I have never had this problem with 10.4.
What gives?

Installation Guide
Instructions for all features and settings.
Boot Camp 4.0 FAQ Get answers to commonly asked Boot Camp questions.
Windows 7 FAQ Answers to commonly asked Windows 7 questions.
Apple Boot Camp Support
Lion's Boot Camp Assistant 4.x should have downloaded Apple drivers as part of also partitioning.
You need Apple drivers. And you then need to add on your own audio driver.
You can run Assistant at any time to download and save a set of drivers.

Airport Card Not Recognized after Leopard Install

After the Leopard install the airport card on my Dual 1.8 G5 is not being recognized (the airport menu reads "no aiport card installed". Of course there is a card and when booting a from Tiger there is no problem. It's a stock apple airport card. Any suggestions?

Interesting update...
After reading several other threads of semi-related topics, I decided that there's no harm in reinstalling the software. After placing in the disk and restarting you get the WELCOME splash screen. On the menu bar, you can choose to view the System Profiler prior to installation. My Airport Card did how up here - telling me that it's not a hardware issue. I'm in the process of re-installing 10.5 - which will take 1-2 hours to complete. I'll let you know how it works out.
parrots

Canon MP 600 Printer not working after Leopard Install

I installed the Leopard OS and now my Canon MP 600 printer that purchased at the MAC store with my Mac in Aug of this year. It was working properly prior to the Leopard install. I tried re-installing the printer drivers, but no change. I can see my MP 600 as the only printer available. I am also unable to even print a 'test' page. When I run the Network Diagnostics everything is fine, but no printing.
Any suggestions?

I tried this. I also tried updating the CUPS config file as was noted elsewhere. The printer is a total no-show on Leopard.
It is being served by an older G4 whose only job is to serve the printer.
On Tiger it would just *be there* to print to. All the Panther computers see it as a "shared printer" in the printer box.
In Leopard.... not a &^^&% thing.
Not happy.
deviztate wrote:
Are you using a gimp driver? I had the same issue and gimp was the cause. I went to the Canon website and found the driver I needed. After the install and restart all was well. In fact, when I opened Print Utility, I saw that the system had already defaulted to the new Canon driver. Here's the Canon link...
http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&fcategoryid=182&mo delid=12892
Navigate to drivers and downloads... Hope this helps...
-d

Demo servlet IsItWorking doesn't work after fresh install

Hello,
We did a fresh install of Oracle 9iAS 1.0.2.2 on Hp-ux 11i
The installation completed succesfully, but
when trying to run the demo servlet IsItWorking, we get error 'The page cannot
be displayed'
The apache error_log file contains following lines:
[Thu Apr 18 17:12:03 2002] [notice] FastCGI: process manager initialized (pid
9809)
[Thu Apr 18 17:12:03 2002] [warn] OPM: ADM: process 9810 created server process
9811 (group group1, module JServ), and inserted in proctable as entry 0
[Thu Apr 18 17:12:03 2002] [emerg] OPM: Watcher starts with an id=9810
[Thu Apr 18 17:12:03 2002] [warn] OPM: ADM: process 9810 created server process
9812 (group group2, module JServ), and inserted in proctable as entry 0
[Thu Apr 18 17:12:04 2002] [notice] Oracle HTTP Server Powered by Apache/1.3.19
(Unix) mod_fastcgi/2.2.10 mod_perl/1.25 mod_oprocmgr/1.0 configured -- resuming
normal operations
[Thu Apr 18 17:12:18 2002] [warn] OPM: EW process rp5400:0 (pid:9811) died,
restarting.
[Thu Apr 18 17:12:18 2002] [warn] OPM: ADM: process 9810 created server process
9819 (group group1, module JServ), and inserted in proctable as entry 0
[Thu Apr 18 17:12:18 2002] [warn] OPM: EW process rp5400:0 (pid:9812) died,
restarting.
[Thu Apr 18 17:12:18 2002] [warn] OPM: ADM: process 9810 created server process
9820 (group group2, module JServ), and inserted in proctable as entry 0
[Thu Apr 18 17:12:21 2002] [warn] OPM: EW process rp5400:0 (pid:9819) died,
restarting.
[Thu Apr 18 17:12:21 2002] [warn] OPM: ADM: process 9810 created server process
9821 (group group1, module JServ), and inserted in proctable as entry 0
[Thu Apr 18 17:12:21 2002] [warn] OPM: EW process rp5400:0 (pid:9820) died,
restarting.
[Thu Apr 18 17:12:21 2002] [warn] OPM: ADM: process 9810 created server process
9822 (group group2, module JServ), and inserted in proctable as entry 0
[Thu Apr 18 17:12:23 2002] [error] OPM:Can not find one alive process
[Thu Apr 18 17:12:23 2002] [error] OPM:Can not find one alive process
[Thu Apr 18 17:12:24 2002] [warn] OPM: EW process rp5400:0 (pid:9821) died,
restarting.
[Thu Apr 18 17:12:24 2002] [warn] OPM: ADM: process 9810 created server process
9824 (group group1, module JServ), and inserted in proctable as entry 0
Any idea?
Thanks

Hi -
I was wondering if you solved this problem. I had the exact same issue on Win2K after I installed the Java Portlet Development Kit. Now my Apache JServ does not work.
This is a sample of my error_log:
[Fri Jun 07 10:48:01 2002] [notice] FastCGI: process manager initialized
[Fri Jun 07 10:48:08 2002] [error] OPM:Can not find one alive process
[Fri Jun 07 10:48:08 2002] [error] [client 127.0.0.1] File does not exist: /servlet/IsItWorking
[Fri Jun 07 10:51:22 2002] [warn] OPM: ADM: Process 380 terminated using SIGTERM successfully
I have re-checked my jserv.properties, jserv.conf, zone.properties several times and I can't see the problem. I tried to manually remove the entire PDK and go back to my original state (I saved a copy of all my config files) but it still doesn't work.
Did you find a way to fix this?
Thanks!!!
Heather

Eject button wont work after leopard install

Once i installed leopard my eject button stopped working on my G5. I have to restart the computer for it to work. Is there anyway to get it to work without having to restart it every time? Should i reinstall Leopard because im missing iphoto and a couple other programs since the first install so i dont know if im missing more?

just a thought .... Leopard uses the "soft" eject feature which requires you to hold down the eject for a second before the tray will open. Helps when you accidentally hit it.
i-Life, i.e., iPhoto,iWeb,iMovie, Garageband, doesn't come with Leopard, you now have to purchase these separate. Unless you buy an Apple computer.
Hope this helps
John

Airport Extreme not found after Leopard install

I have internet, I can access my External drive connected to my Airport Extreme but when I run the Airport Utility, it can't "find" my Airport Extreme. The utility can only find my Express so I unplugged it and now it can't find anything. It's weird because everything works. I want to access the base station to make changes to ports. Can you help?

I used my Tiger-equipped iBook G4 and checked the Airport Utility from there. Sure enough, there was an available update. After I updated, everything worked just fine. Except, for some reason, I can get my Airport Drive to load on Leopard's desktop. I can live with that.

Airport doesn't work after firmware update

Hi.
I was using my home wireless network when the Software Update suggested a firmware update to my Airport. I did it, but since then it doesn't work any more. I mean, the Mac can't find it and it keep flashing the yellow light.
Have this happened to anyone else?
Thanks.
Best regards,
T

Try shutting down the DSL modem and your AirPort base station. Leave them S/D for about 5 minutes, then start the DSL modem, allow it to complete its test cycle, then start the AirPort base station.
Repair Permissions - /Applications/Utilities/Disk Utility.app. Start Disk Utility, select your HD and click on Repair Permissions. When finished, quit Disk Utility and then restart your computer.
Go to System Preferences/Network/AirPort
- click on the 'Network Name:' roll-button, select 'Join Other Network...', enter 'Network Name and select the security type you are using, and finally, enter your Password and click 'Join'.
- click on 'Advanced', TCP/IP and confirm that 'Configure IPv4:' is set to 'Using DHCP', click 'OK'.
- click the 'Apply' button and exit System Preferences.
If the above does not work then a factory reset of your AEB might be in order. The setup manuals for all AEBs are here: http://support.apple.com/manuals/#airport

Sync doesn't work after re-install

''locking this thread as duplicate, please continue at [https://support.mozilla.org/en-US/questions/1015872 /questions/1015872]''
I had sync working on my windows machine, and firefox was always up to date.
After re-installing windows I connected to my Sync straight away account and nothing is updating, no bookmarks, history, passwords, nothing.
No, I haven't upgraded to a new sync or old sync or anything like that, i didn't even know there were different ones. How do I get my data back and sync working again?

Sync isn't meant to be used as a backup device, but merely to sync data between multiple devices.
So it is not guaranteed that you can restore data from the Sync server.
See also:
*http://kb.mozillazine.org/Profile_backup
*https://support.mozilla.org/kb/Backing+up+your+information

Touch doesn't work after clean install of Windows 7 Professional

I have an IQ526t. I did a clean install (remove drive/repartition/format drive) of Windows 7 Professional, and now the touchscreen feature doesn't work. I've been on forums here and at Mirosoft, downloaded various drivers, rebooted multiple times, etc....no luck. I get the sound, but no response. Thoughts???

Hello bmarkj,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand that you have removed the recovery drive and installed Windows 7 by not using the OEM version that came with your computer. You have a couple options here, first you can download and install the HP Support Assistant and let it download and install the software and drivers that came with your computer. You can alter the settings so that the updates are manually done giving you control over what gets updated and what does not. Or you can download and install the drivers and what software you want from HP TouchSmart IQ526t CTO Desktop PC Drivers page. The choice is yours.
***NOTE: Be warned that there is software that come with some of the computers that is ONLY available from the recovery drive so you may not see everything you are used to seeing. The only way of recoverying this software is through the HP Recovery Discs.
I hope I have addressed your question to your satisfaction. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

The 7 key doesn't work after lion install

The 7 key on my MacBook pro keyboard doesn't work following lion installation. (I'm using my iPad right now obviously!)
When I press 7, basically random stuff will come out. A set of 3 to 5 random numbers or some "command" that whatever program I am in doesn't recognize.
I tried rebooting. I have no idea where to even begin, help!

And of course this morning all keys are back to working again! But last night it was 7, J, U gibberish.
At first glance it does seem like something that might be a hardware problem, but I am deeply suspicious of coincidences like this. I'm kind of like house md that way I guess. Especially when at least two of us experienced this.
I think I will also wait for the next software update and see if that helps. At least I have my iPad to use when the keys are on the fritz.
Good luck!

Airport disk just stopped working after Leopard install

My airport disk worked perfectly in Tiger. After installing Leopard i can see airport disks in the finder but when i try to see contents the system hangs up for a few seconds and then i get a message "can't connect to disk" or something similar. I tried reinstalling airport software from cd, upgrading firmware of airport extreme, deleting keys from keychain but still don't work. Any experience?
Thanks

Hi,
This could be related to an authentication issue,could you try to change the authentication of the disk to "With a disk password" or "With base station password" on the disk pane of the airport utility (into the file sharing tab)?
Regards

Boot keys stopped working after Leopard install

I have seen others having this problem in another thread but no answers, so thought I'd give it a go.
After reading these threads finally got Leopard to install and run okay. Many thanks all. But, along the way, my boot keys stopped working. It doesn't matter what I hold down, whether 'c' or 'cmd-opt-p-r' or 'shift' or any other key combination the machine just boots straight into Leopard.
I have tried resetting the PMU (or whatever it is these days) via the internal button in desperation but still no luck.
Anyone with any ideas?

Same problem here, so I'll pull this post up. No key works.
I always have to go to the Start Drive (or whatever it's called in english) in Preferences Panes and choose the partition I wish to start directly in OSX or Windows for booting back to OSX. This is very annoying. Alt key won't show up any possible boot disk although their both internal drives.
If someone would kindly post any ideas how to change that, would be great. I've done a fresh install, with a Time Machine recovery, but this didn't seem to help.
EDIT:
I found another subjet here from november '07:
http://discussions.apple.com/thread.jspa?threadID=1224639
it seems the new Apple Keyboard is the origin of the Problem on iMac Core Duo. Apple techs said that a new firmeware should be coming before the end of 2007 (but it's february 2008 now ?!?). Any other ideas how to get this work ? I'll write on Aplpe feedback page for sure. Maybe the other boot keys aren't working because of this keyboard too.
Message was edited by: Nordlaser

Macbook Pro Audio line in stopped working after Leopard install

Anyone know what's up with this? Since I installed Leopard (did an erase and install) my audio line in port isn't working although my built-in microphone is. Ideas? I haven't found a solution so far from my searches.

I also have this problem but with a slightly different twist..
I was using my plantronics (old ms gamevoice headset) with 10.5.2 and it worked, then installed the m-Audio Firewire Audiophile beta drivers and neither the audio-in or the m-audio audiophile line-in cause any VU-meter response (nor input) whereas the standard inbuilt microphone does.
After uninstalling the m-audio drivers the situation is still the same.
Oddly - if I plug in the headphones into the line-in (rather than microphone) then speak into them I actually get input audio (and VU-meter response) through the MBP's audio-in.
So the story about no power is used (hence the headphones create enough to register the sound) sounds about true... very annoying as I thought my old headset had died and went out and bought a new one.. that still doesn't explain the audiophile input issues..
Now I fully expect both companies to point fingers at each other.. I don't care - just get it fixed please.

AirPort doesn't work after Leopard install

Similar Messages

Maybe you are looking for