Airport Express as an end point on a wireless network and connect a computer via the ethernet port?
Can I use my Airport Express as an end point on a wireless network and connect a computer via the ethernet port? - I'm wanting to connect a computer that does not have wireless and is in another building.
The requirements for this to work are:
1) The AirPort Express must be the 802.11"n" version. Model Number is A1264
2) There must be adequate wireless signal stength where the Express will be located
3) The Express must be configured to "join" the wireless network with the option checked to activate the Ethernet port
Similar Messages
-
Wired airport express to extend wireless network and connect network printer?
Is it possible to configure and connect an Airport Express via ethernet cable to an Airport Extreme base station in order to extend wireless network AND connect a network printer to it? Here's the deal...The Airport Extreme is directly connected to my DSL modem and the wireless network is working fine in my house, but, the signal does not reach my detached studio/office. I have a Cat5e cable (and phone line, more on this later) run between the two locations and trimmed out. I would like to have wireless access and connect my network printer (Brother HL-2170W, wireless or wired) in my studio, be able to use printer from house also, and still have wireless access in house.
So, ethernet connection from Extreme to Express, USB from Express to Printer, wireless access for all users. Can anyone talk me through how to (re)configure the Express to do this? Do I need to make changes to Extreme configuration also?
JSIs it possible to configure and connect an Airport Express via ethernet cable to an Airport Extreme base station in order to extend wireless network AND connect a network printer to it?
Yes. Apple's instructions for this are here:
http://support.apple.com/kb/HT4260
Instead of a second AirPort Extreme as illustrated, you will be using the AirPort Express. -
Operating System: os x 10.9.1
Airport Utility 6.3.2
Airport Express 802.11n (1st generation)
Linkus router: Model WRT310Nv2, Firmware Version 2.0.01
Motorola Cable Modem: Model 2210-02, Firmware 7.7.3r5
The Airport Express (AE) is setup to join my wireless network using Airport Utility. A printer is connected to the AE with a USB cable. After the setup the AE light is green and the printer can be accessed over the wireless network.
The problem starts if the router is cycled off/on. Now the AE will not rejoin the wireless network and there is a non-flashing amber light. If the power to the AE is cycled off/on the AE reconnects to the wireless network.
This is about as handy as a screen door on a submarine.
Is it possible to see the setting of the AE the same way the modem and router settings can be accessed? Can this issue be fixed?If they send you a replacement printer it will have ink tanks with it. You can store the ink tanks from your current printer and use them later on you "new" printer if you wish. Store them nozzle-up so they do not leak.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP -
Can I share internet from a airport express via the ethernet port
I have a older airport express that I am trying to you to share the internet with a Marantz AV receiver. I used to be able to share the internet to a PS2 a few years back.
I was able to set up another network parallel to my normal wireless network with an older moonbase style airport extreme using WDS.
I am unsure if this is the limitation that apple has introduced to the unit, or it is a Telstra firewall issue.
Is it possible using a combination of Airport Etremes or expresses to share the internet to a wired unit?I have a new airport extreme that I use all the time. I was using the older airport express for airplay.
The older airport extreme I just pulled down from the cupboard trying to get the AVR connected.
Since posting I have able to use the Airport extreme to connect the AVR via the ethernet port.
Still curious why I cannot connect using the airport express.
Interestingly the older airport extreme pushed the new airport extreme into WDS mode. Tried to hook up the express and it did not work. -
Adding Airport Express to an existing Windows WEP enabled wireless network
I have can't find anything to help me add my new Airport Express to my existing WEP network. All I want is to use to play my Itunes through the sitting room stereo. I've upgraded the firmware on my Netgear 802.11b wireless access point so I can have a 13 digit WEP password. I've installed the latest install software from the apple website for the express box.
I can access the express box fine on its own but not add it to the existing network. Now the only thing that works is the apple connection! My old wireless network has stopped working. I tried the same at my office yesterday and the only way to resolve the situation was to uninstall all the Apple software and then my Wireless network was able to work again. I'm pulling my hair out here and getting in to trouble with the rest of the family because it is taking so much time up!
Someone mentioned somewhere some new firmware - I can only find one for MAcs not PCs - I don't have any Macs on my network.
Please help.
THANKSMake sure you have installed at least Airport 4.1 on your PC:
http://www.apple.com/support/downloads/airport41forwindows.html
Most Netgear wireless routes will tell you the hex equivalent of the plain text WEP password you enter into it - and this is found using the same web browser based process you use to configure the router. This information cannot be found by any other means (like "pinging" the router's IP address). If you can get the WEP key in this manner, configure the Airport Express with the same WEP key *while it is still cabled to the router*.
The alternative is to come up with a 26-digit hex format WEP key of your own choosing. You can then wirelessly access the Airport Express and enter that WEP key on it first, followed by doing the same on the router second. -
Cannot Connect Airport Express 802.11n to WEP 64 Bit Wireless Network
I am currently use a Netgear MR814 who's only built in security is WEP 64bit.
I am attempting to connect my Airport Express 802.11n to it and I see the WEP 40 bit option and use that and it puts in my password for the wireless as 0xPASSWORD.
However it is unable to connect to the network. I scoured these forums and attempted the "$" escape character and the "" option by none of these work.
Is there a way for me to configure my AE to be able to connect to my (older) wiresless router?I found information indicating that this airport express must be set up by airport utility 5.6.1, but that version is not supported by Lion.
AirPort Utility 5.6.1 is not supported by Lion....it was designed for Snow Leopard.
You need the correct version of AirPort Utility 5.6 for Mac OS X Lion
Give the correct version a try and then please report on your results. -
I have a power mac g5 that does not have a wireless card, and connects to the internet via ethernet cable.
I want to know how to set up an airport express so that it joins my wireless home network and provides the G5 with an internet signal.
This via an ethernet cable that is plugged into the airport express and then into the ethernet port on the g5.
Please advise as I have configured the airport express in every way possible, the green light is on and when I plug the ethernet cable into the G5 my network cofigurations shows nothing and says that the ethernet cable is not plugged in (It is).
I get an internet signal if the ethernet cable is plugged directly into my wireless router, so the ethernet port works.
Please assist. Thanks.Two requirements that must be met to do what you want.......
1) An AirPort Express 802.11n must be used. Check the Model No on the label on the side of the Express. It needs to be A1264. Any other model number will not do what you want.
2) The Express must be configured to "Join a wireless network" and the option to enable Ethernet Clients must be checked.
Open AirPort Utility and click Manual Setup
Click the Wireless tab below the row of icons
The box to "Allow Ethernet Clients" must be checked
Please check to verify that your AirPort Express meets both requirements -
I am considering buying an airport but I am not sure if it will work how I would like it to. I need it for two things. The first would be to use for AirPlay with my home stereo. The second would be to use as a way to give my Xbox 360 a WIRED internet connection via the ethernet port. I would like to do these things simultaneously, rather than constantly changing the configuration and being limited to a single function each time I do so.
Thanks!The 802.11n AirPort Express Base Station (AXn) can be configured as a wireless Ethernet bridge. In this configuration, it would join an existing wireless network and its Ethernet port would be enabled for a wired client, like your Xbox 360. This configuration would also support AirPlay simultaneously.
-
Can AirPort Extreme join a wireless network and share the connection to ethernet connected devices?
Can AirPort Extreme join a wireless network and share the connection to ethernet connected devices?
Yes, if the AirPort Extreme is joining a wireless network that has been created by another Apple router. In this case, it will be extending the wireless network and the Ethernet ports are enabled on the "remote" AirPort Extreme.
No, if the AirPort Extreme will be used with another router from another manfacturer.
Ironically, the less expensive AirPort Express can do what you ask about with virtually any wireless network using a special feature called ProxySTA. It won't extend the wireless with a non-Apple router, but the Ethernet port will be enabled. -
Can't find my Airplay - using Airport Express as an Access Point
Hi,
i've a slight problem with my airport express. i build a network with an easybox 803 router as base and an airport express as an access point in the next room. the airport led shows me that is all fine (green light). but i can't find the airplay service. I suspect that my macbook connects to the base and not to the access point.
now i want to know: how can i config my mac or my airport express, so that i can find the airplay service
best regards and thx for your helpSolved.
I had likely the same problem. It was solved by replacing the home router internal connections with a real switch.
Many home routers will not properly multicast the required Airplay/Bonjour multicasts. Netgear and D-Link for instance does not work, although some ASUS routers work if you turn off IGMP snooping and fiddle with the firewall, but only with some firmware, so it is very iffy.
So, in my case, I connect Internet modem <-> router <-> switch <-> access points <-> devices
Works without any problem. Also the wired devices connect to the switch.
Do not connect any Airplay devices to the router! -
I have an older airport express, but don't know where to look to find its model number.
The version number is airport utility 6.3.4 (634.17).
Can anyone point me in the right direction? Thanks.Hard to see it's so teeny. I needed a magnifying glass.
FWIW, you should not mark your reply as Solved because you did not solve your question. Helpful and Solved are used to reward the user who help you or solved your problem. -
Use Airport Express as wired assess point
Is it possible to use the Airport Express as a wired ethernet access point?
I would like to use it as a receiver from my wireless network, allowing to connect my computer via ethernet cable to the airport express (computer from my employer does not allow wireless and I don't want to sit always next to my modem...).
I already have two airport express stations for my music streaming.
Thanks, FrederikYes you can use an ethernet cable to connect to the Airport Express when it is setup as a wireless access point.
I have an Airport Extreme base station in a back room and an Airport Express in the front room by my XP HTPC. The Expess is an set as an access point and the XP computer is hooked to it via a Cat5 cable. My other computers are wireless and I have no problems connecting to the XP wired machine.
You will need to enable WDS on the Extreme Base Station and you will need to enable the ethernet port on the Express after you set it up as an access point.
I'm a Mac newbie but I hope this answers your questions.
Macbook Pro Mac OS X (10.4.8) Airport Extreme Base Station, Airport Express Access Point, Apple Wireless Mouse -
I connect to the internet using a Verizon FIOS router, 802.11g. The brand name is Actiontec MI424-Rev. D. I stream music from my MacBook Pro and/or iPhone and use an Airport Express to connect to my stereo receiver, which is wired to in-wall speakers. The streaming experience is pretty uneven. The Apple Store recommended an Airport Extreme to beef up the network. Note: this is an average Manhattan apartment, not a vast mansion, but there is lots of interference due to a couple dozen other wireless networks in my building. Which is the best way to set up the network for more robust streaming and fewer dropouts?
Ok, then let's start with the following as the basic configuration of your "single" wireless network.
The Actiontec will be the main Internet router; no configuration changes would be required.
Connect the 802.11n AirPort Extreme Base Station (AEBSn) directly to the Actiontec router by Ethernet; reconfigure the AEBSn as a bridge, and also, reconfigure the AEBSn as the "main" base station in the extended wireless network.
Connect the 802.11n AirPort Express Base Station (AXn), by wireless to the AEBSn. Configure the AXn to extend the wireless range of the AEBSn.
The following are step-by-step instructions on configuring the AirPorts for an extended network:
Dynamic WDS - Extending a Wireless Network Setup
Temporarily connect the AXn directly to one of the available LAN ports on the AEBSn during the setup phase. Once completed, disconnect the AXn and place it at the desired location.
Open AirPort Utility, and then, select the AEBSn.
Choose Manual Setup from the Base Station menu. Enter the base station password if necessary.
Click Internet in the toolbar, and then, click on the Internet Connection tab. Change Connection Sharing to "Off (Bridge Mode)."
Click AirPort in the toolbar, and then, click on the Wireless tab.
Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then, select the “Allow this network to be extended” checkbox.
Next, select the AXn, and then, choose Manual Setup from the Base Station menu. Enter the base station password if necessary.
Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then, choose the network you want to extend from the Network Name pop-up menu.
Enter the base station network and base station password if necessary.
Click Update to update the base station with new network settings.
(ref: Pages 43-44 of Apple AirPort Networks.)
(ref: Wi-Fi base stations: Extending the range of your wireless network by adding additional Wi-Fi base stations) -
How can I set up mhy Airport Express to extend my Time Capsule wifi wirelessly
I want to extend my wifi off my Time Capsule with an Airport Experess in a part of my house that has no data cable ran to it. How do I do this?
ThanksNo more meseges.
في ٢٦/٠٨/٢٠١٤، الساعة ٢١:٤٥، كتب Apple Support Communities Updates <[email protected]>:
New discussion activity
Bob Timmons has posted in the AirPort community.
How can I set up mhy Airport Express to extend my Time Capsule wifi wirelessly
Assuming that you have the model A1264 or A1392 version of the Express, it must be located where it can receive a strong wireless signal from the Time Capsule to be able to extend it correctly.
A good general location would be a point that is about half way between the Time Capsule and other area that needs more wireless coverage.
You will use AirPort Utility on your computer to configure the Express. An iPhone or iPad could be used as well.
We can provide more help....if you need it....but we'll need to know what version of AirPort Utility that you are using on your computer....or whether you want to use an iPhone or iPad to setup the Express.
https://discussions.apple.com/servlet/JiveServlet/downloadImage/2-26506753-46613 2/AboutAirPortUtility.png
To post a reply, go to the discussion in Apple Support Communities.
You are receiving this email from Apple Support Communities. You can change your email preferences in your Apple Support Communities Profile.
TM and copyright © 2014 Apple Inc. 1 Infinite Loop, MS 96-DM. Cupertino, CA 95014.
All Rights Reserved | Privacy Policy | Terms of Use | Apple Support -
Using Airport Express on separate subnet to make isolated Guest Network?
Hi. I've done a search here, I've tried setting this up at my house but haven't figured it out yet.
Friends have Verizon FiOS service. They're using the provided modem as the ethernet router and it is handing out DHCP addresses, and for a number of reasons including their home theater, on demand use, etc., they want to keep the FiOS modem as the router, not an Apple product.
We're using an Airport Extreme and a Time Capsule both in bridge mode to distribute the wireless network and everything works fine. They'd like to add an isolated, unencrypted Guest Network. I know we can't use the Extreme's Guest tab because we're in bridge mode.
But we do have a new Airport Express. It seems like there would be a way to set up a Double NAT on a different subnet and give guest users access to the internet but not to computers, shared volumes, printers, and everything else on the primary, encrypted network.
Is there a way to do this or will every address coming from the FiOS router be on the same subnet? Are there any other horrible consequences from doing this, i.e., the primary network will still operate fine?
If the DHCP range coming from the FiOS router is 192.168.15.001 to 192.168.15.199, do I set the Airport Express IP address manually? To what?
To eliminate the possibility of duplicate IP addresses would you have the Airport Express hand out a small range of IPs on a completely different network area, like 10.0.1.1?
Any other suggestions? Thank you.I was trying to create a primary and guest network division after the router... such as an unusual configuration in the AEBSn after the FiOS router.
At my home I have my cable modem connected to an AEBSn, which is doing my network's routing. But I didn't set a Guest Network on this AEBSn. I am trying to set up a discrete Guest Network downline from this router. (Which would simulate my friend's installation where they're using a FiOS modem/router all in one and we want to create a discrete Guest Network after that.)
But as I guess you've been patiently trying to get through to me, Bob, whatever outlying separation you may be able to create seems to get put back together at the main router.
For example, today I connected a second AEBSn ("AEBSn Guest") to the LAN port of my primary AEBSn router. I set the AEBSn Guest to create a wireless network, and I set that to be a closed encrypted network called "Test," and I enabled unencrypted Guest Networking as usual and told the AEBSn to ignore the Double NAT error.
With this configuration I am able to get on the open Guest SSID, and internet connection is normal. Between the Guest and the primary encrypted network, printing is broken, iPhoto sharing is broken, and so on, but I still see shared volumes and can log in with authentication.
So I can see why a solution to this may have been elusive.
I don't know much about cable TV's subscription services but I took a peek at the set up pages of the Verizon FiOS router and noted there was a lot going on there. Lots of ethernet and cable IP addresses to Set Top Boxes, etc. Not sure if all this could be recreated within the administration of the Airport Extreme, but I am hesitant to risk messing up the Comcast services which are presently working well.
In terms of zooming out to the big picture... when I invite guests to share my internet service, they're usually doing email and web browsing for the weekend but at the end of their stay they want to print their boarding passes... so despite setting up a guest network I might end up giving them access to the main network anyway.
Thanks for the help, Bob.
Maybe you are looking for
-
After enabling of SSL encrypton on LDAP I can't connect anymore to the LDAB. I think the Lions Server supports now the SSL encrypton for Open Directory.
-
Cannot and have never been able to connect to a testing server
Hello I am using Dreamweaver and am trying to set up a testing site using IIS. I can’t get it set up. It says I don’t have administrative privileges. I am the administrator. This is a home computer and I am the only user of the computer. I am ju
-
Help need in drag drop operation in AIR application
I would like to know if there is a way to drag and drop an attachment file from an desktop mail client application(similar to MSoutlook) into an AIR application and make it accessible to the AIR application. I did experiments with this the drag oper
-
How do I take the music from my iPod and load it onto a new computer?
I had to clear the contents from my hard drive and reload everything. When I restart iTunes, I can't get my music back. I don't care if it's on this computer again or another computer, but does anyone have any advice how I can just get my music? I
-
Removing Exif Data with out using "Save for Web"
I have very large files. I need to remove thw EXIF data. I do not want to use "save for web" because it impacts the quality and size (recompresses) of the files. I need the files to remain un changed except for the removal of the EXIF data. I have