Airport Express Connection to 2WIRE 1000HW HomePortal?

New to the Mac world. My MacBook is currenly wirelessy connected using my 2WIRE 1000HW HomePortal. Connection is good but I need to connect a printer wirelessly (through the AE USB connection). The 2WIRE 1000HW is a combination DSL Modem and Wireless Router in one box. Do I need to 'disable' the wireless router portion of the 2WIRE 1000HW and use it just as a DSL Modem, or can I just use the AE and 'join' the existing 2WIRE router? OR would it be better to use the AE as the wireless router? The 2WIRE has an ethernet connection in back. What is the best connection (AE > 2WIRE ethernet)? Do I need to change anything in the 2WIRE or AE settings? Will there be a conflict wireless routers? Thanks!

dijman, Welcome to the discussion area!
Do I need to 'disable' the wireless router portion of the 2WIRE 1000HW and use it just as a DSL Modem, or can I just use the AE and 'join' the existing 2WIRE router?
Either way.
Do I need to change anything in the 2WIRE or AE settings?
If you have the AirPort Express (AX) join the wireless network provided by the 2Wire then no changes need to be made to the AX.
Otherwise you will need to make changes to both.
Will there be a conflict wireless routers?
Not if the AX joins the wireless network or you disable the 2Wire wireless and connect the AX via Ethernet.

Similar Messages

Printing to Airport Express connected Laserjet 1012 very slow after update to 10.6.8

After updating a pair of computers that we have here to 10.6.8, printing to our Airport Express connected HP LaserJet 1012 has become incredibly slow. I timed it and it is taking 2:30 to print a blank page, whereas printing the same blank page under 10.6.7 (on an external drive connected to the same MacBook Pro) happens within 2 seconds. One thing that I have noticed is that when I bring up the HP Printer Queue the computer says 'connecting to printer' for 20 - 30 seconds, then sits at 50% complete on the printing for some time - anyone else running into similar problems?

Because I am not experiencing the same issue I have not needed to apply the CNET article. But just to be clear, did you follow the instructions to the letter?
If you did and it's still not working then you can begin narrowing down where the problem is by following some basic trouble shooting steps. First thing I'd try is creating a new user account (call it TEST ACCOUNT) and leave it alone, then try printing from that account. If it works then you know it's a software issue in your normal user account. If it still doesn't work then what I'd do is:
1. Download 10.6.8 Combo Update at http://support.apple.com/kb/DL1399
2. Disconnect all peripherals (including the printer)
3. Backup using both Time Machine and/or a Bootable Clone using SuperDuper or Carbon Copy Cloner
4. Restart from the Bootable Clone or the Snow Leopard install discs.
     a) choose language
     b) Click Utililities Menu
     c) Disk Utility
     d) highlight the internal HD and the First Aid tab
     e) Repair Disk Permissions, Verify Disk & Repair Disk.
     f) exit Disk Utility and restart in Safe Mode
5. Install the Combo Update
6. Restart normally and test the system
7. Begin connecting peripherals one by one and testing each.

Problems Printing: Airport Express connected HP Laserjet M1319f

Hello,
I have an Airport Express connected via ethernet to my network. Attached to it is a HP LaserJet M1319f MFP printer, via USB. I can get my iMacs and my Windows systems to print to the printer without a problem.
I would like to be able to print logs to it from my OS X Server (10.6.7), which is located quite a distance from the printer. So far, I've had absolutely no luck configuring the Airport-attached printer and getting it to work. From what I've been able to figure out, OS X Server expects any remote printer that it attaches to, to be attached via IPP, TCP/IP, or via Windows. It doesn't seem to want to discover and use the printer via Bonjour.
Any ideas on how I can make this work? Am I missing something obvious?
Thanks!
Sven

See if these guides help, it sounds like a driver issue. Does the printer work correctly when directly connected to the PC?
Ensure that the Macs are not sharing the printer, as this is not needed and the PC should be able to find the printer on the AX.
Printing from a Windows XP PC to a printer attached to an Airport Extreme Base Station or Airport Express
http://www.ifelix.co.uk/tech/1004.html
Printing from a Windows XP PC to a printer attached to an Airport Extreme Base Station or Airport Express using Bonjour
http://www.ifelix.co.uk/tech/1008.html
Problems with finding Printer Driver on Windows XP when using printer connected to Airport Extreme or Express
http://www.ifelix.co.uk/tech/1012.html

Why does 2 Airport Expresses connects to one another instead of connecting to the primary Airport Extreme For internet Connectivity ?

I have Netgear DG834G router only for dsl connectivity wifi connectivity to that router is off. i have connected netgear that provides adsl connectivity to the (Shakeel's Airport Extreme) Airport Extreme dual band Wireless N 5th generation via cat 5 cable so airport extreme is the main wifi device through which i get wifi signals at my home. now our house is big and i have installed the adsl netgear modem and airport extreme router at the same place in my room in the upper story but the signals are weak even in the upper story at the other end of the house so i have installed the new airport express dual band wireless N in the upper story (Kafeel's airport express) and it is connected to the primary airport extreme (Shakeel's Airport Extreme) wireless router in range extention mode it repeats the same ssid. Our ground floor has another airport express dual band wireless N the new one ( Lounge's airport express) signal was weak there so i installed another airport express (Lounge's Airport Express) their and configured it to extend the range of primary router airport extreme (Shakeel's Airport Extreme) in the upperstory with the same ssid. Now the problem i am facing that sometimes lounge's airport express connects to kafeel's airport express instead of connecting to the airport extreme and the signals in lounge are weak because all the devices are connected to kafeels airport express and does not connect to lounge air port express. but when lounge airport express is connected to primary router airport extreme then everything works fine devices connect to lounge airport express and signals are full. i have took pictures of the problem i am facing you will understand better by having a look at it. In normal working setup both the airport expresses are connected to airport extreme which is shown in this picture
The second picture shows when lounge airport express is connected to kafeels airport express and not the airport extreme (Shakeel's Airport Extreme) this is the problem.
isnt there a way to correct this so that they dont connect with each other and connect to the airport extreme ?

Lounge's AirPort Express must be located signficantly closer to Shakeel's AirPort Extreme than it is to Kafeel's AirPort Express, and there must be fewer obstructions in the signal path than the other possible connection.
The reason is that if you want Lounge's AirPort Express to connect to Shakeel's AirPort Extreme, it must receive a significantly stronger wireless signal from Shakeel's AirPort Extreme than it does from Kafeel's AirPort Express.

Airport Express connection questions

This is what I am trying to do. Can I share an internet connection to a computer that does not have a wireless connection through an Airport Express connected to the wireless router and an ethernet cable to the computer?

No the following also work
- a Linksys WRT54G or WRT54GS (not latest versions v5)
- a Belkin Belkin F5D7230-4 and F5D7231
- one specific model from SMC (can't find model number right now)
- one specific model from Buffalo
- BT Voyager 2100
For wireless routers not on this short list - not possible.
In particular, it will not work with any WiFi routers from D-Link or Netgear.
iFelix

Hi, I`d like to connect my Ipad wirelessly to a stereo to listen to my music from the iTunes library on streaming, but also to movies online, games, Goear-) and so on. I guess I can do that using an Airport express connected to the stereo and via airplay

Hi, I`d like to connect my Ipad wirelessly to a stereo to listen to my music from the iTunes library on streaming, but also to movies online, games, Goear…) and so on. I guess I can do that using an Airport express connected to the stereo and via airplay to my Ipad. My question is, can I listen to all the audio that come out from the ipad (movies online, games, Goear…) or only to the music from iTunes library? I`d appreciate any help. Alex.

My question is, can I listen to all the audio that come out from the ipad (movies online, games, Goear…) or only to the music from iTunes library?
On the iPad you can stream videos, photos, or music from the Video, Photos, Music, and YouTube apps to an Apple TV OR just stream music to an AirPort Express Base Station.

AirPort Express connected to an iPod Hi-Fi; iTunes can't find the speaker.

Hi,
I've been trying to get my Hi-Fi to show up in iTunes via an AirPort Express connected to a MBP without much success..
First I had some trouble connecting the Express to my exisisting wireless network (Wireless-N ADSL2+ Gateway WAG300N), but once I changed the WEP key to a correct lenght I got it working (green light on the Express). Actually I'm not quite sure that it's working as intended, the Express won't show up in the Aiport utility, only in the advanced setting of my wireless network (system preferences -> network). Is it supposed to show up in the Utility even though it's connected through my existing wireless network?
I have both and optical and a 'regular' (English is not my first language cable and I've tried both, but the speakers won't show up in iTunes. I've got iTunes looking for external speakers so that shouldn't be the problem.
Any ideas?

Try setting-up AE as if for the first time (perform a hard-reset of the AE).
This time, however, DO NOT connect the AE to your router initially. Connect it directly to your computer via ethernet cable when setting-up. Airtunes should now be enabled (this will not happen if you initially set up AE with AE connected to your wireless router).

Set up Airport Extreme with 2 Airport Express connected by CAT5??

I recently bought an Airport Extreme base station and an Airport Express. My plan was to use to Airtunes with my AV receiver in my basement. Unfortunately, because the distance between these two areas is long (and separated by two floors) I'm not able to get a strong enough signal with the Airport Express to use Airtunes. I bought another Airport Express to put on the middle floor of our house but the signal in the basement was still not strong enough even with this addition.
I do have a way of connecting the middle floor of our house with the basement area by a CAT5 ethernet cable. My plan now is to connect the two Airport Express modules by their ethernet ports with this cable. The Airport Express on the middle floor connects with the Airport Extreme base station wirelessly without any problems. My question is what is the proper setup for the 2nd Airport Express connected by ethernet in my basement.
Airport Tech support said this could be done. They recommended setting up a new wireless network with the 2nd Airport Express by "fooling" into thinking it was connected directly to the router but using the same network name with a different wireless channel as my Airport Extreme base station. This setup actually works for several hours but then the Airport Express module that is connected to the Airport Extreme blinks amber. Interestingly the 2nd Airport Express with usually remain with the green light on.
Does anyone have any suggestions for the best way to set this up regarding network configuration with the Airport Utility?
Thanks

wmskaggs, Welcome to the discussion area!
They recommended setting up a new wireless network with the 2nd Airport Express by "fooling" into thinking it was connected directly to the router but using the same network name with a different wireless channel as my Airport Extreme base station.
That will work with as long as the AirPort Express (AX) is connected via Ethernet. The only other setting you need to make is to configure it to act as a bridge (not sharing a single IP address).
If this one looses connection, then something is wrong with the AX or the Ethernet connection (cable and/or connectors).

Had a Airport Express connected to my stereo and it was working. I brought an Airport Extreme and suddenly it took over and Airport Express stopped working and disappeared from Airport Utility. What I am supposed to do? ar2ro

I have an Airport Express connected to my stereo and it was working without any problem.
Recently I bought an Airport Extreme to use it as my Base Unit connecting it to my DSL.
I followed the instructions of the Airport Utility, and it started working.
Suddenly, problems started happen the Airport express that was connected to the stereo , stopped working and it disappeared from the Airport Utility area , as it did not exist in the network. I tried to reset it but it did not appear in the Airport Utility page.
Apparently I have other problems with the private network that it created because I cannot use it because of problems with the password that was created. I can only use the network that I created for my guest...
I dont know if my problem is a configuration problem or there is problem with the equipment.
I read that other users where having the same problem with the Airport express , using non apple equipment as their base unit , but I thought that using the Airport Extreme was going to be compatible and no problems would happen.
What should I do?

Common Problem. Common solution.
Connect your Express via ethernet cable to the Mac while other network connections on the Mac are switched OFF.
After the Express shows up, change the settings of the Express to join the existing network. Take the appr. settings.
Unplug and reconnect your Mac to the network.
Check if the Express shows up in Airport Utility
Alternative solution:
Hardreset the Express to factory settings
(while on power push the Pin next to the audio plug with a paperclip. Plug out the Express still holding down the little button then replug the Express to power and release button)
After that, the Express will show up in the Airport Utility.
Make all needed settings.
I would prefer the first solution, its easier just to plug a cat5 cable.

I have an Airport Express connected via optical toslink to a dac/amp in turn connected to speakers. When using iTunes I get message "no speakers connected to Airport Express" and audio sound has drop outs.

I have an Airport Express connected via optical toslink to a dac/amp in turn connected to speakers. When using iTunes I get message "no speakers connected to Airport Express" and audio sound has drop outs.

Ok, if you are connecting the AirPort Express Base Station (AX) to the existing wireless network, then the DSL in the next room is most likely a combination DSL modem and wireless router. Thanks for clarifying that for me.
Although they may only be separated by a single wall, the building material used in that wall may be enough to prevent the AX from receving a "good" signal from the DSL router.
Since I don't know what computing equipment you have available, please check out this AirPort User Tip: AirPort - Optimal Base Station Placement to see if you can get some SNR measurements at the location of your AX. To do this properly, you will want to power-off the AX and only get these measurements for the DSL router.

Airport express connect with Imac via lan line or can not?

I using IMac with connect to internet with DSL modem router (having 4 lan ports).
Now I put Airport express connect with one of Lan ports from DSL router and still connect my IMac with DSL router via lan line and still connect to internet via lan line (switch off airport function in Imac).
The Airport express is using for provide wireless internet and printer to my other PC.
My Question is can I still set up as above and connect share file to my PC via airport express?
Forget to tell that I'm very newby to mac.

chounws, Welcome to the discussion area!
Yes you can do that. Configure the AirPort Express (AX) to operate in bridge mode (not sharing a single IP address).

Time Capsule with (2) AirPort Express connection problem

I have (1) Airport Time Capsule with (1) AirPort Express connected. I'm trying to connect another Airport Express but only get a yellow light on the 2nd Express. If I connect it with a ethernet cable I get a green light. How do I connect a 2nd Express?

The 2nd Express needs to be about the same distance from the Time Capsule as the 1st Express....and....it cannot be closer to the 2nd Express than it is to the Time Capsule.
The reason for this is that the Express will pick up the strongest signal and you want the Express to pick up the Time Capsule signal to be able to extend it.
Then, start over as LaPastenague instructs on the 2nd Express and configure it again.

Apple Airport Express connection/setup with Siemens SpeedStream 4200

Hi, i am having trouble getting my macbook pro to recognise the Apple Airport Express connection to broadband via the Siemens Speedstream 4200 supplied by Optus.

and make sure you choose PPoE when you set up your router.
(It's not obvious from the Optus paperwork)

No Airtunes, Airport Express connected (green light)

Hi all,
After many an hour faffing around I finally got the AirPort Express connected to my Windows XP PC. I can edit the configuration using the Admin Utility, and the light on the AirPort Express is solid green (ohh the joy when THAT finally happened).
Alas iTunes (6.0.1.3) doesn't see the speakers. The menu option (under Preferences> Advanced) is ON, I've checked my firewall and have UDP Port 5353 open (both ways), but still nothing.
I'm not using any security on the wireless connection (no need) and I'm approaching my wits end.
I have manually configured the AirPort Express to an IP address instead of using DHCP (which pulled my internet connection) and I ONLY want to stream music, not interested in using it to access the internet.
What am I missing? I've Googled, read many posts on this forum, and THAT post by Simon that everyone links to, but to no avail. I'm SOOO close though, I know it!

Side note: I'm on a PC not a Mac (freudian slip?)
Info: I am on Telewest Broadband (UK) and my cable modem is a Scientific Atlanta Webstar 100 (it's a USB connection to the PC). My wireless connection is a D-Link AirPlus G DWL-G122 USB Adapter.
OK I'll need to pick up a cable as I don't have one.
Questions.
You said: "Then connect the cable modem to the Airport Express ethernet port. Pull power to both the modem and the Airport Express for five minutes or more."
"Pull power"? I take it you mean just leave them plugged into the power (the modem won't work without power anyway).
The reason I ask for clarification is the next line:
"Then plug the modem into power and wait a minute."
Shouldn't it already be plugged in to power, if it's not plugged in, it won't work?!
Finally:
"Your Mac should now, after reconnecting to the Airport Express wireless network, be able to access the internet."
So, is there anyway to configure the Airport Express NOT to access the internet. I'm not bothered about this at all, I just want to stream music downstairs. No internet access required (BY ME, I understand the Airport Express may want it, but does it NEED it).
Apologies for more questions, and many MANY thanks for your responses so far. Once I get this working (and I will), I'll be writing up a detailed set of instructions, screenshots, the works (I'm a technical author by trade ya see).

Using airport express with a 2wire router

I just got Bellsouth DSL with a 2wire dsl modem that is also a wireless router.
It works fine, but I still want to use my airport express to listen to music.
I can't figure out how to do so, though I have tried various configurations
with the airport setup utility. Anyone have any ideas? How can I use
express with another wireless router?

Let's double-check your AirPort Express Base Station's (AX) settings ...
Perform a "factory default" reset of the AX
o (ref: http://docs.info.apple.com/article.html?artnum=108044)
Either connect to the AX's wireless network or connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, make the following changes:
AirPort > Base Station
o Base Station Name: <rename or leave default>
o Base Station Password: <enter desired password>
o Verify Password: <re-enter desired password>
o Remember this password in my keychain: (optional)
o Set time automatically: (unchecked)
AirPort > Wireless
o Wireless Mode: Join a wireless network
o Network Name: <existing 2wire's wireless network>
o Wireless Security: <select the encryption type of the existing wireless network>
o Wireless Password: <enter the existing wireless network password>
o Verify Password: <re-enter the existing wireless network password>
Music
o Enable AirTunes (checked)
o iTunes Speaker Name: <enter desired speaker name>
o iTunes Speaker Password: (optional)
o Verify Password: (optional)
o Click Update to write the new settings to the AX
In iTunes:
iTunes > Preferences... > Advanced > General
o Look for remote speakers connected with AirTunes (checked)

Airport Express Connection to 2WIRE 1000HW HomePortal?

Similar Messages

Maybe you are looking for