Airport Express Model A1088 with Time Capsule Model A1254 configuration problems.

I have a Time Capsule Model A1254 and an Airport Express Model A1264. I run OSX 10.7.4. When I try to configure an older Airport Express Model A1088 the Time capsule does not recognise the older Airport Express after I configure it using Airport Utility version 5.6.
Can anyone help please.

What do you mean "the Time Capsule does not recognize the older AirPort Express"?
Sounds like the AirPort Express needs to be reset and reconfigured.

Similar Messages

  • Airport Express not working with Time Capsule

    I replaced a NetGear wireless router with a new Time Capsule. After some trial and error I got everything that was hanging off the NetGear - 2 x TiVo machines, printer, extra ports for business laptops - working except my "old" Airport Express unit that I had been using to send my iTunes to my stereo tuner. I just cannot get this to connect to the Time Capsule wirelessly no matter what I do. It works just fine when connected wirelessly direct to my iMac but just will not connect to the Time Capsule as a client. Any ideas?
    Thanks in advance.

    I would suggest, reconnecting the Express to the TC again. Use the AirPort Utility to make ALL configuration changes including the network extending settings. Then restart both base stations and check that the settings are still good. Then disconnect the Express and give it a few minutes to initialize. It should connect. If not, then the issue may be either the distance or obstructions (like walls, ceilings, floors, etc.) that is preventing the Express from getting a signal from the TC that is adequate enough to extend.

  • Use airport express wireless printing with time capsule

    I want to add airport express to my time capsule network to take advantage of wireless printing. I have set my AE to join my existing wireless network and connected my printer to the USB port. I logged into AE through Airport Utility and clicked on the printer pane. It shows my usb printer is connected to the AE. Then I went to system preferences to set my print and fax settings to share over network.
    I thought this is correct, but when I click print it tells me the printer is offline. Am I missing a step? I would connect the printer to my time capsule but I need my printer in a different part of the house. Thanks for you help!!

    You have your printer installed at two different locations. To confirm, open System Preferences and then click Print & Fax.
    You should see your printer listed twice in the printer list on the left.
    One is your printing installed at your computer and the other is your printer installed at the AirPort Express.
    When you open a document to print, you have to choose the printer that you want to use. You may still be choosing the printer at your computer. Look for the printer at the Express. If you intend to use the printer at the Express most of the time, you might want to make that your default printer so you don't have to select a device each time you print.
    For more info on printing issues, see the Apple Printer Troubleshooting Guide.
    Keep in mind that not all printers are compatible, even though they may appear connected to your device. If you work your way through the guide and still cannot print, then that's likely the explanation.

  • Airport Extreme (Dual band) with Time Capsule (Dual band) Extension problem

    Hi
    I have an airport extreme (dual band) set up with a dual band Time capsule extending the 5ghz band .. however the mac address that the time capsule says its using is the 2.4ghz band.. I only noticed this while setting up static IP addresses on my network... does this mean it is extending the 5ghz network on a 2.4 ghz band? how do i set it up to just extend the 5ghz properly.. any clarification would be appreciated.
    thanks in advance

    See my answer to your other post.

  • How can I set up mhy Airport Express to extend my Time Capsule wifi wirelessly

    I want to extend my wifi off my Time Capsule with an Airport Experess in a part of my house that has no data cable ran to it. How do I do this?
    Thanks

    No more meseges.
    في ٢٦/٠٨/٢٠١٤، الساعة ٢١:٤٥، كتب Apple Support Communities Updates <[email protected]>:
    New discussion activity
    Bob Timmons has posted in the AirPort community.
    How can I set up mhy Airport Express to extend my Time Capsule wifi wirelessly
    Assuming that you have the model A1264 or A1392 version of the Express, it must be located where it can receive a strong wireless signal from the Time Capsule to be able to extend it correctly.
    A good general location would be a point that is about half way between the Time Capsule and other area that needs more wireless coverage.
    You will use AirPort Utility on your computer to configure the Express. An iPhone or iPad could be used as well.
    We can provide more help....if you need it....but we'll need to know what version of AirPort Utility that you are using on your computer....or whether you want to use an iPhone or iPad to setup the Express.
    https://discussions.apple.com/servlet/JiveServlet/downloadImage/2-26506753-46613 2/AboutAirPortUtility.png
    To post a reply, go to the discussion in Apple Support Communities.                                                             
    You are receiving this email from Apple Support Communities. You can change your email preferences in your Apple Support Communities Profile.
    TM and copyright © 2014 Apple Inc. 1 Infinite Loop, MS 96-DM. Cupertino, CA 95014.
    All Rights Reserved | Privacy Policy | Terms of Use | Apple Support

  • Using Airport Express to Extend a Time Capsule Network: Results (*Long*)

    Thought I would share my recent (2 hours ago) experience with setting up an Airport Express to Extend a Time Capsule 802.11N 5Ghz Network. Basically I just followed the directions in the Apple Airport Utility, using the "Extend a Wireless Network" setting:
    Time Capsule (TC) 802.11N 5Ghz: In computer room
    Linksys (LNK) 802.11g configured as dual network router with TC, also in computer room.
    Airport Express (AE): In living room, about 50' away, several old plaster walls in between.
    According to iStumblr:
    1) I get an 80% signal from my TC when my MacBook is practically sitting on top of it.
    2) I get an 88% signal from my Linksys 802.11g sitting next to the TC
    3) I get 35% signal from my TC when my MacBook is in the living room. This is NOT enough signal, for some reason, to maintain a decent internet connection.
    4) I get a 46% signal from my LNK from the same location. This IS enough signal to connect to the network.
    5) With the AE configured as "Extend a Wireless Network" to the TC, and placed in the living room (again, about 50' from the TC base station), I get a 55% signal from the AE (which shows up as the same name as the TC network, for obvious reasons) Again, enough signal to connect to the network.
    I did some internet speed tests using SpeedTest (take these with a grain of salt, of course)
    1) From computer room over TC: 18Mb/s~22Mb/s average over 2 days of testing
    2) From computer room over LNK: 18Mb/s~22mb/s average over 2 days of testing
    3) From living room over AE(extended network from TC): 5~7Mb/s average in the last 2 hours
    4) From living room over LNK: 12~14Mb/s average over 2 days of testing
    Preliminary conclusions:
    1) Setting up an extended network is pretty straightforward, and works without issue.
    2) My 802.11g network with my old Linksys is far superior than my new extended 802.11N 5Ghz network, at least for internet connection speed.
    3) I feel a bit irritated buying this AE now to extend my 802.11N network, if its not going to give me any advantages over my ancient 802.11g network
    4) File transfers may still be better over the 802.11N-I will test that out at some point.
    5) I have not tried WDS instead of "Extend a Wireless Network"-not sure what the benefits would be.
    Computer Notes:
    MacBook Aluminum-MB(Al) 2.0 C2D (802.11n)
    finds 8 wireless networks in my neighborhood (3 of them are mine)
    MacBook White-MB(Wh) 1.83 CD (802.11g only)
    finds 10 wireless networks in my neighborhood (3 of them are mine)
    Oddly, the signal strength of my networks isn't that different between the two computers-between 2% and 5%, even though it can't see as many networks. The 2 networks the MB(Wh) CAN see are at around 21% and 25% signal-not sure why the MB(Al) can't see them at all.

    Your biggest mistake is confusing signal strength with signal quality. The signal indicator indicates strength and nothing else. You need to be using iStumblr to look at SNR (Signal to noise ratio).

  • Connecting Airport Express via Ethernet to Time Capsule - Lose Internet

    I have a number of Airport Express units throughout my house that are all connected to speakers.  There are 2 Airport Expresses that I want to hardwire (via eithernet) as they are too far away and I tend to get audio dropouts.  I wired the one with no problem.  When I plugged the other in - my internet went out completely.  I confirmed its not an internet or provider issue - its something to do with the Time Capsule.  I will check my Airport Utility and it will show everything out.  When I unplug the second airport, reset the time capsule - all goes back to normal.
    Any ideas on what the issue is?  How I can fix?  I need to hardwire this second airport to avoid the audio drops.  Thanks in advance.

    your best connection is going to be wired, hands down, so long as you have a Cat5e or Cat6 spec'd cable.
    now the N is pretty fast, but if you have the original version TC, running in N only mode will be the best option because running in multi-mode actually slows the N speed down, not making it worth the upgrade to N.
    If you have one of the "Dual Band" models then the issue mentioned above doesn't apply.

  • How do I change the 5 ghz channel on new Airport Express when extended from Time Capsule?

    Hi there. My Airplay device connected to the new Aiport Express keeps cutting out.
    The 5ghz connection on my Time Capsule is set to channel 48. I have a new Airport Express (with Airplay device) extending from the Time Capsule and when I use WiFi Scanner, it shows the Airport Express set to channel 157. What gives? Is there a way to change to channel 48 or does this not matter? I imagine since they're on different channels, they're not talking to each other or am I .
    Thanks in advance for any help.

    I've managed to change the 5gHz of ther Airport Express that's extending the network.
    As mentioned, main AE is on channel 48, and I now have the 2nd AE on channel 36 - which means my TV can now see the network. Also tested speed via my mavbook air on the same 5gHz network as it all seems OK (A while ago I spotted my Time Capsule was on the same channel 48 as main AE and throughput was abysmal! Bad enough to make me reset the TC to factory defaults and setup again - which is when the TC got channel 120).
    Anyway, the fix... I changed the 2nd AE to create a wireless network (instead of extend), and manually set the channel to 36. I then set it back to extend, and it seems to have kept channel 36.

  • Older Airport Express (circa 2006) and Time Capsule

    Inexperienced user who did not find query related exactly to my question in the forum.
    Present set up = New time Capsule (2TB) linked to modem (speed download 8mbps). WiFi working well for mixture of aged Apple iMacs, a MacBook, a MacBook Pro, a new IPad Air2 and a HP Windows laptop. Presently I have two printers - one new wireless Epson (working okay remotely) and an old HP Colour Laser 2600n wired directly by ethernet to the Time Capsule as it is not wireless. The latter printer is my workhorse and used the most.
    Query = I need to move the HP LaserJet to a different location away from the Time Capsule. Therefore I wish to create wireless connectivity for it. I have an older Airport Express (circa 2006 or earlier) which I have not used for many years.
    (A) Can this be configured to work with the current WiFi technology? Or is it preferable to buy the newer Airport Express?
    (B) Any advice on installing the AE on the relocated printer would be welcome. Thank you.

    Here you go....
    Power off the AirPort Extreme if it is is on...and wait a minute
    Then,, hold in the reset button first on the back of the AirPort Extreme, and keep holding it in for an additional 10 seconds while you simultaneously plug the power back into the AirPort Extreme
    Release the reset button after the hold period, and allow a full minute for the AirPort Extreme to restart to a slow, blinking amber light status
    On your iPad home screen....
    Tap Settings
    Tap WiFi
    Tap on AirPort Extreme under the heading of Set Up a New AirPort Base Station
    The utility will take a minute to analyze things, then suggest that the AirPort Extreme be configured to extend the Time Capsule network
    Enter a name for the AirPort Extreme
    Tap Next
    The utility will set up everything for you. When you see the message of Setup Complete, tap Done.  That's it.
    Connect the printer to one of the three LAN <--> ports. You may need to restart both the printer and the AirPort Extreme to get things going.

  • Trouble joining an Airport Express to an existing Time Capsule network

    I have been trying to add an Airport Express to my existing network. Apples to Apples, right? Easy!
    Nope!!!
    I have a 1TB Time Capsule connected to a cable modem. As well as wireless, I also have an 8-port gigabit switch connected to the Time Capsule to extend the network to a series of wired clients around the house. My intention was for the Airport Express to provide better wireless reception upstairs and to stream music from iTunes to my home stereo system.
    I have tried connecting the Airport Express to the Time Capsule directly using Cat5 as well as to the switch (which shouldn't make any difference...) I have tried configuring it to extend the existing network manually as well as through the Airport Utility wizard.
    All seems okay at first but, for some reason, it seems to kick the Time Capsule off the network (it isn't listed in Airport Utility,)and then I can't connect to the internet nor can Time Machine see the disk in the TC for backups!!
    The Airport Express does not even show up in iTunes.
    I hard reset the Airport Express and try again, and same thing...
    What am I doing wrong and how do I repair this?
    Thanks for any help on this issue.

    I haven't heard it called that, but you could say that was true.
    If you are configuring the Express manually, open AirPort Utility - Click Manual Setup
    Click the Base station tab below the icons to assign a name for your device, password and adjust Time Zone settings
    Click the Wireless tab to enter the wireless settings.
    Wireless Mode = Create a wireless network
    Wireless Network Name = Exact name of your main wireless network
    Radio Mode = Your choice depending on what you need. A good general choice would be 802.11n (802.11b/g compatible) as this will allow all devices to connect
    Channel = Automatic
    Wireless Security = Exact same setting as your main wireless network
    Password = Same password as your main wireless network
    Confirm password
    Click the Internet icon
    Connect Using = Ethernet
    Connection Sharing = Off (Bridge Mode)
    Update to save settings.
    This is the way commercial wireless networks are designed, except on a much larger scale. This provides the maximum bandwidth on the wireless network and best performance.
    This is sometimes called a "roaming network" because computers will automatically connect to the wireless access point with the best signal, which will usually be the closest device.
    Message was edited by: Bob Timmons

  • Airport Express streaming iTunes from Time Capsule

    This may seem redundant to other topics, however I have tried the solutions listed without relief. I bought and installed a Time Capsule. My internet connection comes into it and my iMac accesses it wirelessly. I have an Airport Express which I want in the living room to stream music.
    I have hard reset to the default settings on the AE. My TC is set for "extend a network" and my iTunes is set-up to look for remote speakers. When I use Airport Express to set the AE to access the TC network, I get the confirmation that the AE has been reconfigured and that I can wait for the AE to restart. The Airport Express dialog box never gets past that point, leaving me looking at a spinning status wheel.
    From the default settings, my Airport Utility can see both devices, but clicking on the AE dismounts the TC and vice versa. The status bar on the Airport toolbar sees my TC network and not the AE, which I assume would be normal if the AE joined the TC network. Everything up and running, my iTunes cannot see the AE and I do not get the remote speaker dialog box in iTunes.
    It seems to me there should be a simple process to walk through such a generic situation. What am I missing?

    I have hard reset to the default settings on the AE. My TC is set for "extend a network" and my iTunes is set-up to look for remote speakers. When I use Airport Express to set the AE to access the TC network, I get the confirmation that the AE has been reconfigured and that I can wait for the AE to restart. The Airport Express dialog box never gets past that point, leaving me looking at a spinning status wheel.
    If your goal for the AirPort Express Base Station (AX) is just for streaming iTunes, then you want to configure it to "join" the TC's wireless network ... not to extend it. So enabling "extend a network" on the TC would not be necessary.
    To configure the AX to join the TC's wireless network and for AirTunes, please compare the following settings to those currently enabled on the AX:
    AirPort Utility > Manual Setup > AirPort > Wireless tab
    o Wireless Mode: Join a wireless network
    o Network Name: <existing TC's wireless Network Name>
    o Wireless Security: <select the encryption type of the existing wireless network>
    o Wireless Password: <enter the existing wireless network password>
    o Verify Password: <re-enter the existing wireless network password>
    Music
    o Enable AirTunes (checked)
    o iTunes Speaker Name: <enter desired speaker name>
    o iTunes Speaker Password: (optional)
    o Verify Password: (optional)
    o Click Update to write the new settings to the AX
    In iTunes:
    iTunes > Preferences... > Advanced > General
    o Look for remote speakers connected with AirTunes (checked)

  • New airport express and first gen time capsule

    Hello, I have a first generation time capsule and I want to use my new 1392 airport express to both extend the signal and to play music on my stereo. Can I do both of these things with airport express? If so how d I do it? I currently have been using an old express to play music (it is a first gen express) but also now need to extend the signal.
    Thanks!

    Yes you can.
    If the Express has been configured already, start from the beginning with a "hard reset" (see below) then select "New AirPort Express..." from your Mac's Wi-Fi menu. AirPort Utility will launch and lead you through its configuration.
    To "hard reset" an AirPort Base Station: make sure it's powered up, then press and hold its tiny reset button and keep it depressed for five to ten seconds, long enough for its LED to flash amber rapidly. Release the reset button. Then, the LED will glow amber steadily for about a minute. Then, it will flash amber, slowly, about once every second or two, waiting for you to configure it with AirPort Utility.

  • Using an Older (802.11g) Airport Extreme as bridge with Time Capsule

    Several people have inquired about the possibility of having older (802.11g) computers and devices connected through their Time Capsules without disturbing the 802.11n capabilities of their newer equipment.
    The latest version of Designing AirPort Networks Using AirPort Utility --
    http://manuals.info.apple.com/en/DesigningAirPort_Networks10.5-Windows.pdf -- explains (pp. 48-49) that one can configure a dual-band (2.4 GHz & 5 GHz) network of this type by setting up the "second device [i.e., the older Airport Extreme] as a bridge." What is lacking is a clear (at least to me) way of configuring the 2.4 GHz Extreme as such a bridge, although the text states that one need only follow instructions "earlier in this chapter" (which begins at p. 14). When I try to do this, the AirPort Extreme shows up as a separate network.
    Obviously, I am doing something wrong. Can someone walk me through how to configure the AirPort Extreme as a bridge?
    Thanks.

    The MAC support people walked me through a solution to my question about using an older (802.11g) AirPort Extreme and a Time Capsule to form a dual network. The solution turns out to be pretty easy but I am posting it in case anyone else has a similar problem.
    Here's what was involved:
    N-capable equipment: MacBook Pro, IMac, Time Capsule.
    B/G-capable equipment: AirPort Extreme (flying saucer 802.11g); Mac G4; older (802.11g) AirPort Express supporting a network printer; IBM ThinkPad running Windows XP (w/service pack 2).
    Step 1: Using AirPort Utility (manual setup), I set the Time Capsule to run at 5 GHz (click on "Wireless" then "Radio Mode". Under the same "Wireless" tab, I assigned a 13-digit WPA2 password to this network (more about this latter). If you opt to use the 5GHz frequency, you have the choice of WPA2 or nothing. After saving your settings, exit out of the AirPort Utility; you are done with the Time Capsule.
    Step 2: Reset the AirPort Extreme to its default settings by depressing the small reset button while the device is plugged in.
    Step 3: I reopened AirPort Utility, accessed the Extreme and clicked manual setup. (You will loose your connection to the Time Capsule at this point, but this is okay.) At the top of the screen that opens in response to clicking "manual setup," click "internet" and set "connection sharing" to "Off (Bridge Mode)" Next click "AirPort" at the very top of the screen: under "Base Station" I named the Extreme as "G network" and set up a network password. Under "Wireless" I next set up a WEP 40 bit password which was identical to the WPA2 password I used for the Time Capsule. Using a WEP password was necessary, because some of the older computers were not WPA2 compatible. I kept the passwords identical simply as a matter of convenience.
    Step 4: Connect the AirPort Extreme to the Time Capsule using an Ethernet cable between the WAN port of the Extreme, and one of the three LAN ports on the Time Capsule. There is a small, green LED recessed in the LAN port socket; if it lights up, you are in business.
    Step 5: Using a pin, I reset the 802.11g AirPort Express to its default settings, opened AirPort Utility (no need for manual setup for this), named the Express "Printer" and added it to the G network in a conventional manner by following the setup prompts. (If anyone needs help with this, let me know). Exit out of AirPort Utility and reopen it to refresh; all wireless devices (3 in my case) should be visible and lighted green.
    Step 6: I set up the MacBook Pro and the IMac to join the 5 GHz Time Capsule network, and everything else to run on the G network. At this point, everything appears to be working. I can, for example, print a document from my MacBook Pro (N-network) to the network printer which on the G-network. (Because the older computers belong to my daughters, I'll never know if file sharing across the networks is a possibility.)
    I take no credit for any of this; it was all accomplished through the efforts of very patient MAC support people.
    Carl

  • How can i connect my existing airport express to my new time capsule network?

    I have an older airport express for wirelessly extending my network in my apartment. I bought a new Time Capsule and my airport express flashes amber and cannot find the time capsule to connect. How do I get them connected?

    You can use the USB3 connections for USB2.  That's downward compatible.  Just runs at USB2 speed.
    Just this week apple announced a couple of TB adapters, TB-to-ethernet and TB-to-firewire.  But the FW adapter is not at the apple store as yet (at least at the time I am posting this).

  • Airport Express extension connection from Time Capsule failing

    I have an Airport Express extending my wifi network from a Time Capsule. The connection between them appears to fail frequently. That is, a device connected wirelessly to the Airport Express will lose internet access but will regain it when I power down the Airport Express forcing the device to connect directly to the Time Capsule. Then when I power up the Express again the device connects there and has internet access. Cycling the Express seems to re-establish a working connection between it and the Time Capsule. Is there a solution to this in the settings of either device?

    Once you have WiFi Explorer installed on your Mac, temporarily power off the AirPort Express and locate your laptop as close as possible to the location of the AirPort Express
    Open WiFi Explorer and look for the SNR heading.
    SNR is signal-to-noise ratio, which is a good way to analyze connection quality. The 'bars" at the top of the Macs screen are there pretty much for show...and they tell you nothing about the noise that may be present in the signal.
    Use the following SNR guide to analyze the quality of your connection at the location of the Express:
    40+          Superior
    35            Excellent
    30            Very Good
    25            Good
    20            Fair
    15            Low
    10            Very Low
    5              Not useable
    A reading somewhere between 25-30 should provide a reliable connection for the Express to "extend". Things fall off quickly below 25 though, so if you see anything below that value, that indicates either too low of a signal or too much noise on the connection.
    The Express can only "extend" the quality of signal that it receives, so a good SNR is critical to reliable performance.

Maybe you are looking for

  • Profit Center Document not getting generated when direct FI doc is posted

    Dear Experts, Profit Center Document not getting generated when direct FI doc is posted. However CO Document is generated for Line Item 1 mentioned below. Accounting Entry Line 1 -Debit Expense ( Cost Center) 1000 Line 2 - Credit Bank                

  • OT: PHP mail issue

    I have the following code for sending an email - $message="Line1\n\r"; $message.=$row_rsContact['contactFName'].' '.$row_rsContact['contactLName'].' User#'.$row_rsContact['contactRecord']."\n\r"; $message.="Email - ".$row_rsContact['contactEmail']."\

  • How to create OAImageBean manually URGENT

    Hi, I need to create OAImageBean manually. Please share some ideas how I can achieve this. I'm using this code to do it... OAPageLayoutBean pageLayoutBean = pageContext.getPageLayoutBean(); OAImageBean imageBean=(OAImageBean)createWebBean(pageContext

  • Canoscan 8600f

    Updated to Leopard now scanner CANONSCAN 8600F (which worked fine before) won't copy, and will only scan one page before message recieved cannot communicate with scanner! Any ideas plse? I haven't found the CANON website much help!

  • Just bought a laptop, screen is messed up

    I just bought an Asus laptop a little over a week ago, and the screen is suddenly messing up. It was fine, I fell asleep, I woke up, and now there is this weird shadowing at the top and the screen is flickering. Should I just exchange it? Is it somet