Airport Extreme Card Not Working Properly (Web Browsing Slow)

Hello people of apple discussions,
I have the original MacBook Pro with Mac OS X 10.5.7 installed on it. And I have a problem, my airport extreme card is not functioning properly like when I go on the internet, it comes up with the server "www.google.com" cannot be reached or the same with Yahoo! Back when it had 10.4 it was functioning properly with very high speeds. But, all the other PCs in the house gets good internet even my iPhone and the router is functioning properly. It's been like this since for about 6-8 months and i am very upset with my mac!:|So can I have some help or any suggestions!
Message was edited by: mr.ts

Have you tried contacting your ISP? Sometimes they can help you optimize your settings. Such as DNS server numbers. I had a simullar problem and found out my DNS settings were wrong.
Do you have other computers that use the wireless single? If not you might look into your router to see if maybe something is wroung with it. You can always go to a wifi hotspot or a friends house and see how the connection is there. If it seems normal then you know it is your ISP or your router. If not then it might be a laptop problem.

Similar Messages

  • Airport extreme card not working with leopard / G5

    I just upgraded my PowerMac to leopard (G5 dual 1.8, 3 gigs of ram, 250 GB HD). I bought it new in December 2004 from apple. Previously I had been using a USB adapter to connect to my wireless internet at home (Linksys WRT54G). This device does not support leopard so I got an airport extreme card from gainsaver.com.
    The Airport extreme card is configured properly as far as I know but it will only connect to my network for about 5 seconds then it drops. The USB adapter worked perfectly in the same spot and my macbook right next to it works fine as well.
    1. Could it be a bad Airport extreme card?
    2. Is this a known issue? And possibly be resolved with the 10.5.2 update?
    It is a fresh Leopard install with no updates as I can not connect it to the internet to get them. Any help would be very much appreciated.
    Message was edited by: anthonylkelly

    Hi, I have the same machine (4 ram slots?) have you got the connector for the aerial that connects to the motherboard attached to your airport card. Mine works a treat.

  • Javascript does not work in web browser

    Hello friends.
    I have a problem with javascript in my Captivate project.
    This script only works in preview in Captivate, but does not work in web browser (IE 9, Mozilla, Chrome).
    Anybody knows why?
    Thank you for your answers.

    Common JS interface
    That is the official documentation for JS in Captivate 8. For more information, have a look at Jim Leichliter's website: CaptivateDev.com - eLearning Development with Adobe Captivate

  • Not working properly Computer Browser service in Windows Server 2012

    Good afternoon.
    Migrated from 2003 to 2012 Active Directory, all is good, but the service Computer Browser in Windows Server 2012 is not working properly.
    Online, there are several hundred computers, one network, no segments. PDC is the Master Browser, it is in my list of all the computers, but gives customers or Backup Browser computers only part, and in alphabetical order, giving the first 70 computers and
    all.
    Looked packet sniffer:
    Microsoft Windows Lanman Remote API Protocol 
    Entry Count: 70 
    Available Entries: 251
    So on Master Browser shows 251 computer, and the client 70.
    If disabled on Windows Server 2012 Service Computer Browser, Master Browser is a computer running Windows Server 2003. He gives all computers.
    What is the problem, how to get Windows Server 2012 to work correctly as a Master Browser?

    More info. I have high lighted in bold where the issue is. This is a massive headache for me at the moment
      Frame: Number = 377, Captured Frame Length = 182, MediaType = ETHERNET
    - Ethernet: Etype = Internet IP (IPv4),DestinationAddress:[00-13-72-52-6E-A1],SourceAddress:[00-1E-0B-2B-68-DD]
      - DestinationAddress: Dell Inc. 526EA1 [00-13-72-52-6E-A1]
         Rsv: (000000..)
         UL:  (......0.) Universally Administered Address
         IG:  (.......0) Individual address (unicast)
      - SourceAddress: 001E0B 2B68DD [00-1E-0B-2B-68-DD]
         Rsv: (000000..)
         UL:  (......0.) Universally Administered Address
         IG:  (.......0) Individual address (unicast)
        EthernetType: Internet IP (IPv4), 2048(0x800)
    - Ipv4: Src = 10.44.46.101, Dest = 10.44.44.14, Next Protocol = TCP, Packet ID = 14025, Total IP Length = 168
      - Versions: IPv4, Internet Protocol; Header Length = 20
         Version:      (0100....) IPv4, Internet Protocol
         HeaderLength: (....0101) 20 bytes (0x5)
      - DifferentiatedServicesField: DSCP: 0, ECN: 0
         DSCP: (000000..) Differentiated services codepoint 0
         ECT:  (......0.) ECN-Capable Transport not set
         CE:   (.......0) ECN-CE not set
        TotalLength: 168 (0xA8)
        Identification: 14025 (0x36C9)
      - FragmentFlags: 16384 (0x4000)
         Reserved: (0...............)
         DF:       (.1..............) Do not fragment
         MF:       (..0.............) This is the last fragment
         Offset:   (...0000000000000) 0
        TimeToLive: 128 (0x80)
        NextProtocol: TCP, 6(0x6)
        Checksum: 0 (0x0)
        SourceAddress: 10.44.46.101
        DestinationAddress: 10.44.44.14
    - Tcp: Flags=...AP..., SrcPort=65372, DstPort=NETBIOS Session Service(139), PayloadLen=128, Seq=1910965363 - 1910965491, Ack=580319796, Win=252 (scale factor 0x8) = 64512
        SrcPort: 65372
        DstPort: NETBIOS Session Service(139)
        SequenceNumber: 1910965363 (0x71E70473)
        AcknowledgementNumber: 580319796 (0x2296FA34)
      - DataOffset: 80 (0x50)
         DataOffset: (0101....) 20 bytes
         Reserved:   (....000.)
         NS:         (.......0) Nonce Sum not significant
      - Flags: ...AP...
         CWR:    (0.......) CWR not significant
         ECE:    (.0......) ECN-Echo not significant
         Urgent: (..0.....) Not Urgent Data
         Ack:    (...1....) Acknowledgement field significant
         Push:   (....1...) Push Function
         Reset:  (.....0..) No Reset
         Syn:    (......0.) Not Synchronize sequence numbers
         Fin:    (.......0) Not End of data
        Window: 252 (scale factor 0x8) = 64512
        Checksum: 0x6F65, Disregarded
        UrgentPointer: 0 (0x0)
        TCPPayload: SourcePort = 65372, DestinationPort = 139
    - Nbtss: SESSION MESSAGE, Length =124
        PacketType: SESSION MESSAGE, 0(0x00)
      - Flags: Add 0 to Length
         Reserved: (0000000.)
         Extension: (.......0)Add 0 to Length
        Length: 124(0x7C)
    - SMB: C; Transaction, Remote Administration Protocol, FileName = \PIPE\LANMAN
        Protocol: SMB
        Command: Transaction 37(0x25)
      - NTStatus: 0x0, Facility = FACILITY_SYSTEM, Severity = STATUS_SEVERITY_SUCCESS, Code = (0) STATUS_SUCCESS
         Code:     (................0000000000000000) (0) STATUS_SUCCESS
         Facility: (...0000000000000................) FACILITY_SYSTEM
         Customer: (..0.............................) NOT Customer Defined
         Severity: (00..............................) STATUS_SEVERITY_SUCCESS
      - SMBHeader: Command, TID: 0x2001, PID: 0x276C, UID: 0x3801, MID: 0x0140
       - Flags: 24 (0x18)
          LockAndRead:     (.......0) LOCK_AND_READ and WRITE_AND_UNLOCK NOT supported (Obsolete) (SMB_FLAGS_LOCK_AND_READ_OK)
          NoAck:           (......0.) An ACK response is needed (SMB_FLAGS_SEND_NO_ACK[only applicable when SMB transport is NetBIOS over IPX])
          Reserved_bit2:   (.....0..) Reserved (Must Be Zero)
          CaseInsensitive: (....1...) SMB paths are case-insensitive (SMB_FLAGS_CASE_INSENSITIVE)
          Canonicalized:   (...1....) Canonicalized File and pathnames (Obsolete) (SMB_FLAGS_CANONICALIZED_PATHS)
          Oplock:          (..0.....) Oplocks NOT supported for OPEN, CREATE & CREATE_NEW (Obsolete) (SMB_FLAGS_OPLOCK)
          OplockNotify:    (.0......) Notifications NOT supported for OPEN, CREATE & CREATE_NEW (Obsolete) (SMB_FLAGS_OPLOCK_NOTIFY_ANY)
          FromServer:      (0.......) Command - SMB is being sent from the client (SMB_FLAGS_SERVER_TO_REDIR)
       - Flags2: 51207 (0xC807)
          KnowsLongFiles:            (...............1) Understands Long File Names (SMB_FLAGS2_KNOWS_LONG_NAMES)
          KnowsEas:                  (..............1.) Understands extended attributes (SMB_FLAGS2_KNOWS_EAS)
          SmbSecuritySignature:      (.............1..) Security signatures enabled (SMB_FLAGS2_SMB_SECURITY_SIGNATURE)
          Compressed:                (............0...) Compression Disabled for REQ_NT_WRITE_ANDX and RESP_READ_ANDX (SMB_FLAGS2_COMPRESSED)
          SecuritySignatureRequired: (...........0....) Security Signatures are NOT required (SMB_FLAGS2_SMB_SECURITY_SIGNATURE_REQUIRED)
          Reserved_bit5:             (..........0.....) Reserved (Must Be Zero)
          IsLongName:                (.........0......) DO NOT use Long File Names (SMB_FLAGS2_IS_LONG_NAME)
          Reserved_bits7_9:          (......000.......) Reserved (Must Be Zero)
          ReparsePath:               (.....0..........) NOT a Reparse path (SMB_FLAGS2_REPARSE_PATH)
          ExtendedSecurity:          (....1...........) Aware of extended security (SMB_FLAGS2_EXTENDED_SECURITY)
          Dfs:                       (...0............) NO DFS namespace (SMB_FLAGS2_DFS)
          Paging:                    (..0.............) Read operation will NOT be permitted unless user has permission (NO Paging IO) (SMB_FLAGS2_PAGING_IO)
          NTStatus:                  (.1..............) Using 32-bit NT status error codes (SMB_FLAGS2_NT_STATUS)
          Unicode:                   (1...............) Using UNICODE strings (SMB_FLAGS2_UNICODE)
         PIDHigh: 0 (0x0)
         SecuritySignature: 0x0
         Unused: 0 (0x0)
         TreeID: 8193 (0x2001)
         ProcessID: 10092 (0x276C)
         UserID: 14337 (0x3801)
         MultiplexID: 320 (0x140)
      - CTransaction:
         WordCount: 14 (0xE)
         TotalParameterCount: 32 (0x20)
         TotalDataCount: 0 (0x0)
         MaxParameterCount: 8 (0x8)
         MaxDataCount: 4200 (0x1068)
         MaxSetupCount: 0 (0x0)
         Reserved: 0 (0x0)
       - Flags: Do NOT disconnect TID
          Disconnect: (...............0) Do NOT disconnect TID
          NoResponse: (..............0.) Server response to the client
          Reserved:   (00000000000000..) Reserved
         Timeout: 5000 milli sec(s)
         Reserved2: 0 (0x0)
         ParameterCount: 32 (0x20)
         ParameterOffset: 92 (0x5C)
         DataCount: 0 (0x0)
         DataOffset: 0 (0x0)
         SetupCount: 0 (0x0)
         Reserved3: 0 (0x0)
         ByteCount: 61 (0x3D)
       - RemoteAPIBuffer:
        - FileName: \PIPE\LANMAN
         - Align: 1 Bytes
            AlignBytes: Binary Large Object (1 Bytes)
           Name: \PIPE\LANMAN
          Pad1: Binary Large Object (2 Bytes)
    - RAPRequest: NetServerEnum2 Request, InfoLevel = 1, SV_TYPE_ALL: All in NSNET
        RAPOpcode: NetServerEnum2
      - ParameterDescriptor: WrLehDz; 4 send, 1 receive parameter
         Param: (W) WORD (send parameter, 16 bit integer)
         Param: (r) Receive buffer (format in data descriptor) (receive data, 0 bit integer)
         Param: (L) Receive buffer length (send/receive parameter, 16/16 bit integer)
         Param: (e) Entries read (receive data, 0 bit integer)
         Param: (h) WORD (receive parameter, 16 bit integer)
         Param: (D) DWORD (send parameter, 32 bit integer)
         Param: (z) ASCIIZ (send parameter, 8 bit integer)
         Param: ASCII NUL (string terminator)
      - DataDescriptor: B16BBDz; data bytes send: 0, receive: 34
       - Datum: (B) BYTE[16] (receive data, 8 bit integer)
          Datum: (B) BYTE (receive data, 8 bit integer)
          Digit: 1
          Digit: 6
         Datum: (B) BYTE (receive data, 8 bit integer)
         Datum: (B) BYTE (receive data, 8 bit integer)
         Datum: (D) DWORD (receive data, 32 bit integer)
         Datum: (z) ASCIIZ* (receive data offset, 32 bit integer)
         Datum: ASCII NUL (string terminator)
      - NetServerEnum2: SV_TYPE_ALL: All in NSNET
         InfoLevel: (1) SERVER_INFO_1
         ReceiveBufferSize: 4200 (0x1068)
       - ServerType: SV_TYPE_ALL: All
          Workstation:      (...............................1) All workstations
          Server:           (..............................1.) All computers with the server service running
          Sqlserver:        (.............................1..) All running Microsoft SQL Server
          DomainCtrl:       (............................1...) All primary domain controllers
          DomainBakctrl:    (...........................1....) All backup domain controllers
          TimeSource:       (..........................1.....) All Time servers
          AFP:              (.........................1......) All Apple File Protocol servers
          Novell:           (........................1.......) All Novell servers
          DomainMember:     (.......................1........) All LAN Manager 2.x domain members
          PrintqServer:     (......................1.........) All print servers
          DialinServer:     (.....................1..........) All dial-in servers
          ServerUnix:       (....................1...........) All Unix/Xenix servers
          NT:               (...................1............) All Windows NT workstations or servers
          WFW:              (..................1.............) All Windows for Workgroups servers
          ServerMFPN:       (.................1..............) All Microsoft File and Print for NetWare servers
          ServerNT:         (................1...............) All non-domain controller servers
          PotentialBrowser: (...............1................) All servers that can run the browser service
          BackupBrowser:    (..............1.................) All backup browsers
          MasterBrowser:    (.............1..................) All master browsers
          DomainMaster:     (............1...................)  All domain master browsers
          Reserved1:        (..........11....................)
          Windows:          (.........1......................) All Windows 95 or later
          DFS:              (........1.......................) All DFS root servers
          ClusterNT:        (.......1........................) All NT Clusters
          Terminalserver:   (......1.........................) All Terminal Servers
          ClusterVSNT:      (.....1..........................) All NT Cluster Virtual Server Names
          DCE:              (....1...........................) AllIBM DSS (Directory & Security Services)
          Reserved2:        (...1............................)
          AlternateXport:   (..1.............................) Return list for alternate transport
          LocalListOnly:    (.1..............................) Return local list only
          DomainEnum:       (1...............................) Enumerate primary domain
         Domain: NSNET
    Then the reply;
        Frame: Number = 378, Captured Frame Length = 1514, MediaType = ETHERNET
    + Ethernet: Etype = Internet IP (IPv4),DestinationAddress:[00-1E-0B-2B-68-DD],SourceAddress:[00-13-72-52-6E-A1]
    + Ipv4: Src = 10.44.44.14, Dest = 10.44.46.101, Next Protocol = TCP, Packet ID = 27036, Total IP Length = 1500
    + Tcp: Flags=...A...., SrcPort=NETBIOS Session Service(139), DstPort=65372, PayloadLen=1460, Seq=580319796 - 580321256, Ack=1910965491, Win=253 (scale factor 0x8) = 64768
    + Nbtss: SESSION MESSAGE, Length =2013
    + SMB: R; Transaction, Remote Administration Protocol
    - RAPResponse: NetServerEnum2 Response, Count = 31
        Win32ErrorCode: 0x00000000 - ERROR_SUCCESS - The operation completed successfully.
        Converter: 2251 (0x8CB)
      - NetServerEnum2: Count = 31
         EntriesReturned: 31 (0x1F)
         EntriesAvailable: 31 (0x1F)
       + NetServerInfo1: APOLLO
       + NetServerInfo1: ARTEMIS
       + NetServerInfo1: ASKLEPIOS
       + NetServerInfo1: CASTOR
       + NetServerInfo1: DCC4503-131L
       + NetServerInfo1: DCC4503-155L
       + NetServerInfo1: DCC4503-157L
       + NetServerInfo1: DCC4503-161L
       + NetServerInfo1: DCC4503-171L
       + NetServerInfo1: DCC4503-172L
       + NetServerInfo1: DCC4503-175L
       + NetServerInfo1: DCC4503-177L
       + NetServerInfo1: DCC4503-183L
       + NetServerInfo1: DCC4503-184L
       + NetServerInfo1: DCC4503-185L
       + NetServerInfo1: DCC4503-188L
       + NetServerInfo1: DCC4503-196L
       + NetServerInfo1: DCC4503-197L
       + NetServerInfo1: DCC4503-199L
       + NetServerInfo1: DCC4503-202L
       + NetServerInfo1: DCC4503-203L
       + NetServerInfo1: DCC4503-205L
       + NetServerInfo1: DCC4503-210L
       + NetServerInfo1: DCC4503-213L
       + NetServerInfo1: DCC4503-219L
       + NetServerInfo1: DCC4503-220L
       + NetServerInfo1: DCC4503-228L
       + NetServerInfo1: DCC4503-233L
       + NetServerInfo1: DCC4503-234L
       + NetServerInfo1: DCC4503-236L
       + NetServerInfo1: DCC4503-241L
        StringData: Binary Large Object (586 Bytes)

  • AirPort Extreme card not compatible with Mac Pro???

    Hey,
    I recently purchased my Mac Pro without thinking to include any hardware for connecting to a wireless network.
    I have recently moved into a new apartment which I am keen to join to a wireless network which has just been set up by my roommate for his PC and Laptop.
    I was going to buy an AirPort Extreme card, but I have read that it is not compatible with the Mac Pro. Yet when I looked at the configure process for a new mac it was listed as one of the devises offered for wireless networking!!
    I am very confused...
    I was wondering if anyone could help me, i just need to know what hardware i will need and how it would be installed.
    thanks, all help will be greatly appreciated!
    Mac Pro   Mac OS X (10.4.8)  

    the mac pro takes a slightly different airport express card. you have to purchase it at the retail store and have them install it. in my experience they will not allow you to purchase one and install it yourself due to the difficulty of installing it. best thing to do take your macpro into a apple retail store and see what they can do.

  • AirPort Extreme Card not being recognized

    I installed an AirPort Extreme Card into my powerbook G4 15" laptop. I also installed the software from the CD that came with the card. Everything went just like the instructions set out. When I start my computer and go into the system profiler it doesn't show that I have an airport card installed. Also if I launch the AirPort Setup Assistant it claims I have no card installed.
    How can I determine the card is installed correctly and working?

    Which PowerBook G4 do you have?
    Some PowerBook G4s require the original AirPort card.
    Others require the AirPort Extreme card.

  • Can't get Airport Extreme card to work in G5 Powermac

    I'm probably being a dummy, but I need some help.
    My main computer is just under two years old and has funcioned on a network through ethernet. Internet access comes through cable and I have a Linksys wireless router. My G4 ibook has operated on this network with an airport card quite successfully.
    I decided to get rid of some cables and put the G5 on wireless. I installed an Airport Extreme card, connected the antenna. The Network Status panel tells me that the Airport card is turned on but not connected to a network. The signal indicator on the menu bar is greyed out.
    Any attempts I have made to find a network signal or configure the card seem to be doomed.
    What am I doing wrong?

    IF those are the only two options, I don't know what it could be.
    Going backwards,
    Double check your antenna on the card.
    Pull up Software Update, perhaps an update will come up for this situation.
    Boot to an OSX install disk, Run Disk Util and run a Disk Repair then Disk Permissions Fix. Unlikeley bit worth a shot
    Return the card?
    Sorry man...

  • Is there a way to update firmware on airport extreme card to work with "n"?

    I have a airport extreme card in my G4 Powerbook and want to know if I can somehow update that card to make it compatible with the new "n" wireless standard?
    Even if I can't, should I update the firmware and if so, how do I go about doing it?
    Thanks!
    Dan

    No there is no software update that will give that card 802.11n capability.
    Your PowerBook can join an 802.11n network as long as that network is configured to operate in an 802.11b/g compatible mode. You will not get the speed benefits of 802.11n since your PowerBook will be operating at 802.11g.
    You may want to take a look at QuickTek's products.

  • PB's Airport Extreme card not staying connected - please help diagnose

    My thread Airport extremem card can't hang onto wifi signal - what to do? in the "Getting Online" forum hasn't generated a solution, so I'm trying here too.
    In the past few weeks, my airport signal bounces around and randomly disconnects me. It goes from no signal (indicated) to 3 bars then bounces around. It occurred with my own Airport Extreme card (in the PB) and my Belkin router, and the library's wifi.
    The problem may have started after an erase-and-install of Panther with an upgrade using the combo 10.3.9. The only security updates I see receipts or packages of are SecUpd2005-004Pan.pkg, SecUpd2007-002Pan.pkg, SecurityUpdate2004-10-27Pan.pkg.
    The usual troubleshooting (Permissions, Chrons, Disk Warrior) didn't solve anything. Since first posting about this problem I've reapplied the 10.3.9 combo. I tried changing the channel on the router and setting it to Protected Mode.
    "Protected Mode
    NOTE: In most situations, best performance (throughput) is achieved with Protected Mode OFF. If you are operating in an environment with HEAVY 802.11b traffic or interference, best performance may be achieved with Protected Mode ON."
    I then installed Airport 4.2 update because Software Updater presented it as an option.
    Until today iStumbler and MacStumbler were showing 29-35% signal strength with no noise. As of today, iStumbler is showing intermittent noise of ~14-21%, but MacStumbler is not. (It was constant when I tried channel 9 and changing the router's back to 10 made it intermittent.)
    The router is serving a desktop computer via ethernet so I can't move it. I have reset the router and cable modem several times with no improvement.
    Does anyone have any ideas what I can do? Thanks.

    I would have come back to edit this, to say that the dropping signal problem came back since the 10.3.9 combo but I couldn't. The darn wifi signal was lost for something like 7 minutes.
    The PB was sitting in exactly the same place and toggling airport on and off wouldn't reconnect it. It generated many lines in the console. Anyone know what this means?
    Aug 5 12:05:04 Marlinespikes-Computer kernel: AirPort: Link DOWN (AP deAuth 0)
    Aug 5 12:05:04 Marlinespikes-Computer kernel: handleAirPortChangesChannelWL fails because POWER IS OFF (the mask is correcty set however)
    Aug 5 12:05:13 Marlinespikes-Computer kernel: AirPort: Link DOWN (out-of-range 0)
    Aug 5 12:05:13 Marlinespikes-Computer kernel: handleAirPortChangesChannelWL fails because POWER IS OFF (the mask is correcty set however)
    Aug 5 12:05:17 Marlinespikes-Computer kernel: AirPort: Link DOWN (out-of-range 0)
    Aug 5 12:05:17 Marlinespikes-Computer kernel: handleAirPortChangesChannelWL fails because POWER IS OFF (the mask is correcty set however)
    2007-08-05 12:05:20.931 iStumbler[3432] WirelessCreateScanResults context:0x382A50 err: 0x88001003
    2007-08-05 12:05:29.930 iStumbler[3432] WirelessCreateScanResults context:0x382A50 err: 0x88001003
    2007-08-05 12:05:45.326 System Preferences[4011] connection:didFailWithError: can’t find host
    Aug 5 12:05:53 Marlinespikes-Computer last message repeated 5 times
    2007-08-05 12:05:56.930 iStumbler[3432] WirelessCreateScanResults context:0x382A50 err: 0x8800100B
    2007-08-05 12:06:32.930 iStumbler[3432] WirelessCreateScanResults context:0x382A50 err: 0x8800100B
    Aug 5 12:08:07 Marlinespikes-Computer last message repeated 14 times
    : object: ./Applications/iTunes.app/Contents/MacOS/iTunes malformed object (inconsistant sizeofcmds field in mach header)
    Aug 5 12:09:59 Marlinespikes-Computer last message repeated 8 times
    Aug 5 12:11:55 Marlinespikes-Computer lookupd[3999]: NetInfo connection failed for server 127.0.0.1/local
    Aug 5 12:11:56 Marlinespikes-Computer lookupd[3999]: NetInfo connection failed for server 127.0.0.1/local
    Aug 5 12:11:56 Marlinespikes-Computer kernel: AirPort: Link Active: "belkinrouter" - 0011501e80e9 - chan 8
    Aug 5 12:11:56 Marlinespikes-Computer kernel: handleAirPortChangesChannelWL fails because POWER IS OFF (the mask is correcty set however)
    Aug 5 12:12:05 Marlinespikes-Computer configd[129]: SecKeychainFindGenericPassword err= -25308 ( =0xffff9d24) (current= belkinrouter)
    (event handler):Can't find variable: autoSave
    (event handler):Can't find variable: autoSave

  • Swing components in applet not working in web browser

    Hi Guys,
    I've created an applet which makes use of some swing components, but unfortunately, not all of them function properly in my web browser (internet explorer or Mozilla Firefox). Its mainly the buttons; the last buttons works and displays the correct file within the broswer, but the first 5 buttons do not work...
    any help please on how I can sort this problem out?
    Heres the code for my applet:
    import java.awt.*;
    import java.awt.event.*;
    import javax.swing.*;
    import java.applet.*;
    public class MainAppWindow extends JApplet
    int gapBetweenButtons = 5;
    final JPanel displayPanel = new JPanel(new BorderLayout());
    public void init()
       //Panel for overall display in applet window.
       JPanel mainPanel = new JPanel(new BorderLayout());
       mainPanel.add(new JLabel(new ImageIcon(getClass().getResource("images/smalllogo2.gif"))),BorderLayout.NORTH);
       //sub mainPanel which holds all mainPanels together.
       JPanel holdingPanel = new JPanel(new BorderLayout());
       //Panel for displaying all slide show and applications in.
       displayPanel.setBackground(Color.white);
       displayPanel.add(new JLabel(new ImageIcon(getClass().getResource("images/IntroPage.jpg"))),BorderLayout.CENTER);
       displayPanel.setPreferredSize(new Dimension(590,400));
       JPanel buttonPanel = new JPanel(new GridLayout(6,1,0,gapBetweenButtons));
       buttonPanel.setBackground(Color.white);
       JButton button1 = new JButton("User guide");
       button1.addActionListener(
         new ActionListener() {
              public void actionPerformed(ActionEvent e)
                   if(displayPanel.getComponents().length > 0)displayPanel.removeAll(); // If there are any components in the mainPanel, remove them and then add label
                   displayPanel.setBackground(Color.white);
                   displayPanel.add(new JLabel(new ImageIcon("images/UserGuide.jpg")));
                   displayPanel.revalidate(); // Validates displayPanel to allow changes to occur onto it, allowing to add different number images/applicaions to it.
       JButton button2 = new JButton("What is a Stack?");
       button2.addActionListener(
       new ActionListener() {
               public void actionPerformed(ActionEvent e)
                   if(displayPanel.getComponents().length > 0)displayPanel.removeAll();
                   displayPanel.setBackground(Color.white);
                   displayPanel.add(new JLabel(new ImageIcon("images/WhatIsAStack.jpg")));
                   displayPanel.revalidate();
       JButton button3 = new JButton("STACK(ADT)");
       button3.addActionListener(
       new ActionListener() {
             public void actionPerformed(ActionEvent e)
                   if(displayPanel.getComponents().length > 0)displayPanel.removeAll();
                   displayPanel.setBackground(Color.white);
                   displayPanel.add(new JLabel(new ImageIcon("images/StackADT.jpg")));
                   displayPanel.revalidate();
       JButton button4 = new JButton("Stacks in the Real World");
       button4.addActionListener(
       new ActionListener() {
             public void actionPerformed(ActionEvent e)
                   if(displayPanel.getComponents().length > 0)displayPanel.removeAll();
                   displayPanel.setBackground(Color.white);
                   displayPanel.add(new JLabel(new ImageIcon("images/StacksInTheRealWorld.jpg")));
                   displayPanel.revalidate();
       JButton button5 = new JButton("DEMONSTRATION");
       button5.addActionListener(
       new ActionListener() {
             public void actionPerformed(ActionEvent e)
                 if(displayPanel.getComponents().length > 0)displayPanel.removeAll();
                 Demonstration app = new Demonstration();
                 JPanel appPanel = app.createComponents();//gets the created components from Demonstration application.
                 appPanel.setBackground(Color.pink);
               displayPanel.add(appPanel);
               displayPanel.revalidate();
       JButton button6 = new JButton("Towers Of Hanoi");
       button6.addActionListener(
       new ActionListener() {
             public void actionPerformed(ActionEvent e)
                     if(displayPanel.getComponents().length > 0)displayPanel.removeAll();
                     TowerOfHanoi app = new TowerOfHanoi();
                     JPanel appPanel = app.createComponents();//gets the created components from Towers of Hanoi
                     JPanel mainPanel = new JPanel();//panel used to centralise the application in center
                     mainPanel.add(appPanel);
                     mainPanel.setBackground(Color.pink); //sets mainPanel's background color for 'Towers Of Hanoi'
                     displayPanel.add(mainPanel);
                     displayPanel.revalidate();
       //adding buttons to the buttonPanel.
       buttonPanel.add(button1);
       buttonPanel.add(button2);
       buttonPanel.add(button3);
       buttonPanel.add(button4);
       buttonPanel.add(button5);
       buttonPanel.add(button6);
       JPanel p = new JPanel(); // Used so that the buttons maintain their default shape
       p.setBackground(Color.white);
       p.add(buttonPanel);
       holdingPanel.add(p,BorderLayout.WEST);
       holdingPanel.add(displayPanel,BorderLayout.CENTER);
       //Positioning of holdingPanel in mainPanel.
       mainPanel.add(holdingPanel,BorderLayout.CENTER);
       //indent mainPanel so that its not touching the applet window frame.
       mainPanel.setBorder(BorderFactory.createEmptyBorder(10,20,10,20));
       mainPanel.setBackground(Color.white);
       mainPanel.setPreferredSize(new Dimension(850,600)); //size of applet window
       mainPanel.setOpaque(false); // Needed for Applet
       this.setContentPane(mainPanel);
    }

    Thanks for the response. I don't quite understand what you're talking about though. I have, in my humble knowledge, done nothing with packages. I have put the applet class (WiaRekenToolActiz.class is the applet class) in the jar file wia_actiz_archive.jar. From what I read on the tutorial, java looks for the applet class in all the jar files specified. Since I put my CODEBASE as the main url, I thought it baiscally didn't matter where you out the html file.
    I shall include the complete html page complete with applet tag to perhaps illuminate a bit more what I mean...
    <html>
    <head>
    <title>Wia Rekenmodule hello!</title>
    </head>
    <body bgcolor="#C0C0C0">
    <applet
    CODEBASE= "http://www.creativemathsolutions.nl/test"
    ARCHIVE= "Actiz/wia_actiz_archive.jar, Generic/wia_archive.jar"
    CODE="WiaRekenToolActiz.class" 
    WIDTH=915 HEIGHT=555
    >
    <PARAM NAME = naam VALUE = "Piet Janssen">
    <PARAM NAME = gebdag VALUE = "01">
    <PARAM NAME = gebmaand VALUE = "06">
    <PARAM NAME = gebjaar VALUE = "1970">
    <PARAM NAME = geslacht VALUE = "man">
    <PARAM NAME = dienstjaren VALUE = "10">
    <PARAM NAME = salaris VALUE = "56500">
    <PARAM NAME = deeltijdpercentage VALUE = "100">
    <PARAM NAME = accountnaam VALUE = "Zorginstelling 'De Zonnebloem'">
    </applet>
    </body>
    </html>

  • AirPort Extreme on a Network Requiring Web Browser Login

    I was looking into purchasing one of the new AirPort Extreme routers to use in my dorm. My school requires you to log in to its network through a web browser the first time you connect before you can gain any network or internet access. After you log in once your MAC address is stored and you are given an IP and allowed to access the network. My current Linksys wired router passes this page through to connected clients without a problem, but I tried using an older graphite AirPort base and it would not pass the page through and my MacBook Pro was unable to connect to the college network through it. My question is will the new AirPort Extremes pass this login page through and allow my Macbook Pro to login to the network through Safari?

    That would make sense on most networks as you want the school's main router to only "see" one device, the router in your room. Then you can have your router assign IP addresses to as many devices as you want and the school's router still only "sees" one device.
    If you configure your router as a bridge, then the school's router will be assigning IP addresses to each device connected to the router, probably not what you want.
    The default mode for the AirPort Extreme is to act as a router. It will assign IP addresses in the 10.0.x.x range by default, but you can set it to assign IP's in the 192.168.x.x range if you prefer. You will probably get a Double NAT notice when you hook the router up. Click "ignore" and the message will go away.
    I use an AirPort Express quite a bit for travel. If the hotel has an ethernet port, I can plug in and hook up 2-3 wireless devices and pay for only one connection.
    Nothing is ever certain. If you go with the AirPort Extreme, might be a good idea to check the store's return policy...just in case.
    Message was edited by: Bob Timmons

  • Urgent!!! Forms not work on web browser(OAS 10g,Solaris 10 x86).

    Problem discribe:
    1.environment:
    (1)Network: only local network.
    (2)Platforms
    All platforms we use are Solaris 10 for X86.
    (2.1)Server: (intel) Solaris 10 for X86
    Oracle Application Server Forms Services 10.1.2.0.2
    (2.2)Client: Mozolla web browser on (intel) Solaris 10 for X86 .
    Mozolla web browser information:
    (2.2.1)[menu]-[Help]-[About web browser]display:
    Welcome to Mozilla 1.7 for Sun Java(TM) Desktop System
    Mozilla/5.0 (X11; U; SunOS i86pc; zh-CN; rv:1.7) Gecko/20070606
    (2.2.2)[menu]-[Help]-[About Plug-in]display:
    Java(TM) Plug-in 1.5.0_12-b04
    file name： libjavaplugin_oji.so
    Java(TM) Plug-in 1.5.0_12
    MIME type
    application/x-java-vm Java
    application/x-java-applet Java
    application/x-java-applet;version=1.1 Java
    application/x-java-applet;version=1.1.1 Java
    application/x-java-applet;version=1.1.2 Java
    application/x-java-applet;version=1.1.3 Java
    application/x-java-applet;version=1.2 Java
    application/x-java-applet;version=1.2.1 Java
    application/x-java-applet;version=1.2.2 Java
    application/x-java-applet;version=1.3 Java
    application/x-java-applet;version=1.3.1 Java
    application/x-java-applet;version=1.4 Java
    application/x-java-applet;version=1.4.1 Java
    application/x-java-applet;version=1.4.2 Java
    application/x-java-applet;version=1.5 Java
    application/x-java-applet;jpi-version=1.5.0_12 Java
    application/x-java-bean Java
    application/x-java-bean;version=1.1 Java
    application/x-java-bean;version=1.1.1 Java
    application/x-java-bean;version=1.1.2 Java
    application/x-java-bean;version=1.1.3 Java
    application/x-java-bean;version=1.2 Java
    application/x-java-bean;version=1.2.1 Java
    application/x-java-bean;version=1.2.2 Java
    application/x-java-bean;version=1.3 Java
    application/x-java-bean;version=1.3.1 Java
    application/x-java-bean;version=1.4 Java
    application/x-java-bean;version=1.4.1 Java
    application/x-java-bean;version=1.4.2 Java
    application/x-java-bean;version=1.5 Java
    application/x-java-bean;jpi-version=1.5.0_12 Java
    2.Install Config:
    (2.1)formsweb.cfg
    after install,
    /export/home/ias/OraHome_2/forms/server/formsweb.cfg
    include a section :
    # Page displayed to users to allow them to download Sun's Java Plugin.
    # Sun's Java Plugin is typically used for non-Windows clients.
    # (NOTE: you should check this page and possibly change the settings)
    jpi_download_page=http://java.sun.com/products/archive/j2se/1.4.2_06/index.html
    # Parameter related to the version of the Java Plugin
    jpi_classid=clsid:CAFEEFAC-0014-0002-0006-ABCDEFFEDCBA
    # Parameter related to the version of the Java Plugin
    jpi_codebase=http://java.sun.com/products/plugin/autodl/jinstall-1_4_2-windows-i586.cab#Version=1,4,2,06
    # Parameter related to the version of the Java Plugin
    jpi_mimetype=application/x-java-applet;jpi-version=1.4.2_06
    (2.2)run oracle test form and my forms
    http://s216:7777/forms/frmservlet?form=test&userid=scott/tiger@orcl
    (Oracle simple test demo form)
    or
    tttp://s216:7777/forms/frmservlet?form=myform&userid=scott/tiger@orcl
    (2.3)browser dialogue window display:
    [title:Default Plugin]
    This page contains information of a type (application/x-java-applet;jpi-version=1.4.2_06)that can only be viewed with the appropriate Plug-in.
    Click OK to download Plugin.
    when I Click Ok ,display warning :
    File not found:www.sun.com, check filename ,try later.
    (2.4)change formsweb.cfg
    /export/home/ias/OraHome_2/forms/server/formsweb.cfg
    change:
    jpi_mimetype=application/x-java-applet;jpi-version=1.4.2_06
    to:
    jpi_mimetype=application/x-java-applet;
    (2.5)run again oracle test form and my forms
    http://s216:7777/forms/frmservlet?form=test&userid=scott/tiger@orcl
    (Oracle simple test demo form)
    or
    http://s216:7777/forms/frmservlet?form=myform&userid=scott/tiger@orcl
    (2.6)Problem:
    myform and test(Oracle simple test demo form) can run and display,
    but all buttons(when click) not work(no response);
    all meuns not work...........
    How to Solve this problem?
    thanks in advance.

    The currently supported versions with patches installed are as follows:
    <li>10.1.2.3 (10.1.2.0.2 + patch 5983622)
    <li>11.1.1.4 (11.1.1.2 or 11.1.1.3 + patch 11060983 : this also requires WLS 10.3.4)
    Fusion Middleware (FMw) 11 downloads are available from here:
    http://www.oracle.com/technetwork/middleware/weblogic/downloads/index.html
    Patches are only available to customers with access to MyOracleSupport (http://support.oracle.com)
    For Forms/Reports users, look for the FMw download titled "Portal, Forms, Reports and Discoverer". The distribution includes all that is necessary to design and deploy your applications. Note that WebLogic Server is also required and is a separate download (from the same page). Be sure to carefully review the installation instructions before attempting the process. It may also be helpful to review MyOracleSupport note 1073776.1.

  • F10 Key not working in Web Browser mode

    I created a click box on a CP5 screen and assigned F10 as the Shortcut key and the action is "Go to the next slide."  When the user presses F10 the demo would advance to the next screen.
    This works great in preview mode.  However, when in Web Browser mode, nothing happens except I get this message at the bottom of the screen, "Contains commands for working with selected item."
    How do I get the F10 key to work (action desired: advance to the next screen in my demo) in browser mode?

    Hi there
    LIkely it depends on the browser, but some keys are always reserved for use by the browser itself and they cannot be used as shortcut keys by a Captivate SWF because the browser will intercept them and not pass them on to the SWF.
    I'm not sure if F10 is among those keys, but it may well be.
    This would likely beg the question of why Captivate would allow you to assign a shortcut key if if wouldn't work when you publish and play in the browser. And for that I would remind you that SWF output is just one of the ouputs Captivate may produce. If you published as EXE, you aren't bound by browser behavior and the key would likely work just dandy.
    Cheers... Rick
    Helpful and Handy Links
    Captivate Wish Form/Bug Reporting Form
    Adobe Certified Captivate Training
    SorcerStone Blog
    Captivate eBooks

  • Quicktime Movie Controller Will Not Work in Web Browser

    Regardless if it's Safari or Firefox, I cannot click any of the buttons on the movie controller when viewing my movies in a web browser. They work as intended in iWeb, however.

    Well I figured it out. Apparently if the video is too low on the page it will not play. I had to change the Y value, moving it up, and it would magically play. Weird...

  • Airport Extreme ethernet not working with Windows XP

    Windows XP no longer connects to the Internet via the Airport Extreme ethernet port. XP says the cable isn't plugged in but when I connect XP directly to the DSL modem it works fine. When I connect my MacBook Pro to the Internet through the Airport Extreme ethernet port it works fine. (I'm sure it's connected by ethernet because I do +sudo ifconfig en1 down+.) I can't figure it out. I'm relatively certain Airport Extreme is blocking XP from connecting via ethernet but I'm not certain. It worked without a glitch for about two years. Lightning fried my old DSL modem and ever since I got the new one, XP "can't see" Airport Extreme, but will connect directly to the DSL modem and the net without a hitch. Any insight will be much appreciated.

    I'm not sure why your PC is not able to connect to the AirPort Extreme Base Station's (AEBS) Ethernet port, but it is likely the lightning strike may have something to do with it. I'm also a bit surprised you're were able to run the "sudo ifconfig" command under Windows.
    To rule out general communications issues between the modem and the AEBS, I suggest that you try a complete power recycle of all your network components as follows ...
    Try the following, in order, checking for Internet access after each step, until resolved:
    1. If the modem has a reset switch, use it to reset the modem. Wait at least 5-10 minutes for the modem to initialize.
    2. Remove power from the modem. If it has a backup battery, remove this as well. Wait 5-10 minutes. Replace the battery, and add power back to the modem.
    3. Perform a complete power recycle of your network components as follows:
    Modem/Router Power Recycling - Quick
    o Power-off the modem, AEBS, & computer(s); Wait at least 5 minutes.
    o Power-on the modem; Wait at least 5 minutes.
    o Power-on the AEBS; Wait at least 5 minutes.
    o Power-on the computer(s)
    If this fails to get the modem to "recognize" the Internet router, then try the "Full" version.
    Modem/Router Power ReCycling - Full
    o Power-off the modem, AEBS, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
    o Power-on the modem; Wait at least 15 minutes.
    o Power-on the AEBS; Wait at least 5 minutes.
    o Power-on the computer(s)
    4. Contact your ISP to have them perform a "modem reset."

Maybe you are looking for

  • Is there a solution yet for FCPX eating all the RAM?

    FCPX is eating all my RAM and 'Memory Clean' keeps having to kick in so that the system doesnt stop completely. I have searched various forums and sites for an answer but noone seems to have a solution yet. My events and projects are all on external

  • Crystal Report Toolbar images not displaying properly in IE?

    Hi, I am using VisualStudio 2012 ,crystal report version 13.0.2000.0 and sp5. My problem is that after loading crystal report, toolbar image icons (such as print,export etc) are not showing properly in internet explorer(version ie10). But it is displ

  • What is the best practice to create IDM user and target accts via recon

    usecase: LDAP<--->idm---->AD. User exists in LDAP. IDM and AD are empty. Need to create IDM user and AD acct from LDAP data. I can recon against LDAP and create the IDM user. But I cannot create AD acct in the same recon process. What is the best pra

  • Logging in... (users on server)

    We are a school and recently just added a few students so they can log in with their own user name. When the new students try to log in they get this message..."You are unable to log in to the user account "user name". Logging in failed because an er

  • Trace the value in which table

    Hi, i have 3 tables T1 node_id T2 node_id, object_type T3 node_id, object_type my requirement is T1 node_id exists in which table(T2 or T3). If T1 node_id exists in T2 then return T2 object_type else return T3 object_type can you please help me to ac