Airport Extreme Compatible Printers - How can you tell by the printer spec?

Hi,
If a printer spec says Mac OS X v10.3.9, 10.4 compatible am I safe in assuming it has drivers for Airport Extreme? If not how can I be sure? I'm trying to replace an old printer that doesn't work very well or have drivers specifically for the Airport Extreme.
My OS is Tiger.

There are no drivers specifically for A-Extreme. You should refer to this list:
http://www.ifelix.co.uk/tech/1013.html

Similar Messages

  • How can you tell who the original sender of a group text is on an iPhone 5, when all that appears is a list of recipients in no particular order

    how can you tell who the original sender of a group text is on an iPhone 5, when all that appears is a list of recipients in no particular order? I can't seem to identify the sender in the details list.

    Start a separate thread to the original sender.

  • Generic wsdl - how can you tell what the field assignment is?

    When using the generic wsdl, it seems that your custom fields are mapped to fields such as:
    customcurrency12
    customtext4
    When accessing the asset class, how can tell what field is assigned to what custom value? When I look in the admin > application customization > asset > asset field setup
    I can see the list of fields and field types but not the number on the end so that I can assign it in my web service code. Is there a way to see what your custom fields are mapped to (i.e. custom standard discount is mapped to custompercent11)
    Thanks in advance any help you can lend on this,
    AspnetDev

    You can use the getMapping web service to get al ist of all the fields for a record type. for each field you get the ElementName (which is what you get in the generic wsdl) and DisplayName which you can use it to match to your fields.
    <Field>
         <DisplayName>My Custom Field</DisplayName>
         <ElementName>CustomText74</ElementName>
         <DataType>Text (Short)</DataType>
    </Field>
    -JLV

  • Diagnostic Mode: How can you tell if the scan disk is working?

    I put my ipod into diagnostic mode and went to the scan hard drive utility. The problem is that does not seem to be working.
    I get the following message:
    Read Verify Scan
    Scan takes a while
    Before Scan:
    Start Scan…
    Does that mean the scan is in process or do I have to do something to start it?

    Mine is doing exactly the same thing. Did you ever get the answer to your question?

  • How can I tell if the print driver was updated?

    I am sorry to ask such a basic question, but I cannot for the life of me figure it out. I'm in System Profiler>Printers and I can see me printer says the driver version is 3.0.1. Is this the right place to check drivers? I have downloaded an update to make it vs. 7.3.1, but it hasn't changed.
    I am trying to get my HP 2355 AOI to scan (like everyone else), and I can't figure out what to do after the download and install of 2350731EN-1.dmg. I download it, install it and yet the driver version doesn't change. I think I am missing a step.
    Thanks.
    iMac G5 20   Mac OS X (10.4.3)  

    I am sorry to ask such a basic question, but I cannot
    for the life of me figure it out. I'm in System
    Profiler>Printers and I can see me printer says the
    driver version is 3.0.1.
    This is the version number for HP's current drivers for most of their inkjets and multifunction devices.
    Is this the right place to
    check drivers? I have downloaded an update to make
    it vs. 7.3.1, but it hasn't changed.
    This is the version number for HP's multifunction device driver set. It includes the printer driver, the scanner driver, and assorted other stuff.
    I am trying to get my HP 2355 AOI to scan (like
    everyone else), and I can't figure out what to do
    after the download and install of 2350731EN-1.dmg.
    I download it, install it and yet the driver version
    doesn't change. I think I am missing a step.
    You did everything right. HP's site is less than clear on the matter.
    You should be able to scan using the drivers in the 7.3.1 driver set, plus a graphics app such as Photoshop or Graphic Converter. There should be an app called (I think, I'm not at home where my HP MFD lives right now) HP Scan which will be called by the graphics app, or by HP Image Zone, and can be launched by itself if necessary.
    Some HP MFDs can also use VueScan. HP MFDs don't seem to like Apple's Image thingie.

  • How Can You Tell if the URLRequest Variables Are Posted?

    Hi,
    This sounds really odd, because I happen to have three variables I am supposed to pass to an httpservice and have the results output to my Flex app.
    The problem is, I don't know how I can tell if a variable has been posted or not, because no matter what I do, it looks like my trace statement is accurate, but there is nothing shown on the screen.
    I tried changing it to GET, and then I get this IO Event Handler error, because my variables are so long.
    var loader:URLLoader = new URLLoader();
            var url:String = "http://localhost/generic.php";
            var variables:URLVariables = new URLVariables();
                variables.from= from_string;
                variables.state_colors = state_colors_string;
                variables.change = change_string;                       
            var encode:String= encodeURI(url);
            var pattern:RegExp = /#/g;
            var decode:String = encode.replace(pattern,"%23");
            var request:URLRequest = new URLRequest(decode);           
            request.method = URLRequestMethod.POST;          
    I am wondering if my variables have been passed correctly. Is there some other way other than using trace statements?
    Thanks for your help.

    Hi,
    Thanks for the tip, and I have just done that with my php code end. It turns out that the file was generated, and the file is blank after the code has finalized execution.
      So, I guess that my POST variables is definitely not posted.
    By the way, I have added a couple of lines for security and IO checks, like you suggested, and here is the almost complete code:
    public function changeMap():void{                        
            var url:String = "http://localhost/generic.php";
            var variables:URLVariables = new URLVariables();
                variables.from= from_string;
                variables.state_colors = state_colors_string;
                variables.change = change_string;
            var encode:String= encodeURI(url);
            var pattern:RegExp = /#/g;
            var decode:String = encode.replace(pattern,"%23");
            var request:URLRequest = new URLRequest(decode);           
            request.method = URLRequestMethod.POST;       
            var loader:URLLoader = new URLLoader();
            loader.addEventListener(SecurityErrorEvent.SECURITY_ERROR, onSecurityError);
            loader.addEventListener(IOErrorEvent.IO_ERROR, onIOError);
            loader.addEventListener(Event.COMPLETE, onLoadComplete);   
            loader.load(request);                    
             private function onSecurityError(event:SecurityErrorEvent):void {
                trace("securityErrorHandler: " + event);
             private function onIOError(event:IOErrorEvent):void {
                trace("ioErrorHandler: " + event);
            public function onLoadComplete(event:Event):void {             //event output                             
    From the console, the error events returned nothing from the addEventListeners.
    When I used GET before, they worked with two passing variables, but since my variables are now more than 512 characters, I cannot put this on the url, which is why I am insisting on using POST here.
    Have I done anything else wrong here?
    Thanks for your help.

  • How can you tell if the line has errors?

    I'll try and keep this as brief as possible.
    <background>
    For 2years (up to 6months ago) I was on BE ADSL and was very impressed with the quality of the service (low latency, decent bandwidth) on my line.  However when I heard that FTTC was being rolled out I switched to Zen internet on the understanding that I could then switch to the FTTC product as soon as it was available.
    Immediately after switching to Zen I started to experience problems with VOIP (I use VOIP extensions against an externally hosted PBX) and was seeing CRC errors on the line.  In the process (~2months) of getting this diagnosed the FTTC product became available and since I wanted uncapped switched to BT Infinity for Business Option 2.
    </background>
    I now find that again I get sporadic VOIP problems (but not as bad as on the ADSL2 service via Zen) but very regular BBC iPlayer dropouts listening to the radio.
    Due to the previous problems whilst on ADSL2 I suspect I still have a minor line fault but as I can't access any stats on the line have no way to verify.  Does anyone have any pointers on where to get line stats to see what is going on on the connection? I can't get any info out of the OR modem.
    Regarding my network.  I am using a cabled, gigabit connection directly to a Draytek 2820n which is in turn doing the PPPoE through the BT OR modem.  I use two different machines and experience the same issues on both.  I'm a server & network admin by trade so pretty sure it's not my internal infrastructure at fault.
    My IP profile is apparently 38717 Kbps down / 10000 KBps up.
    BT Speed tester shows achieved 26581 down and 4912 up though

    jmansford,
    I may be wrong about this as I am only refering to my own 2750n settings,but looking at your upload throughput test results some if not all of your problems could be due to a wrongly wieghted QoS setting and/or port capacity setting based on QoS.
    As you line profile is ok at 38717 Kbps down / 10000 KBps up it looks like there is no problem on your actual line,but phone line noise test might find some crackle,but I don`t think so.
    By your post,you say your are routing PPPoE through the Draytek into the OR modem.?
    If so,maybe you could try leaving the OR or Draytek out of the chain as a process of testing where faults [if any] are.?
     To sum up a bit imo leaving the OR modem out of the net chain might be a better way as I only use the 2750n on it`s own as the OR modem is not then needed.
    Opps! sorry I might be wrong in my above thinking,but is your Draytek just a router or a modem/router combined like the 2750n.?
    But either way the QoS setting are still important.

  • How can you tell where the time source is on solaris 9?

    we have a time synch issue that needs resolving and I have to check where each server involved gets its time from.
    I know in windows you just run a query of net time /querysntp
    what do you do on solaris 9?

    philbo_baggins wrote:
    we have a time synch issue that needs resolving and I have to check where each server involved gets its time from.
    I know in windows you just run a query of net time /querysntpWindows has a default method of time synchronization, and your query may give you information about that. But there are other ways of doing time synch, even on windows.
    what do you do on solaris 9?Solaris 9 doesn't have a default time synchronization method set up out of the box. You have to configure it. So it depends on what you've configured. NTP is common, but not the only method.
    If you're using NTP then 'ntpq -pe' can give you information about what's happening at this point in time. I don't know whether you'd prefer that or perhaps looking at the overall configuration.
    Darren

  • How can you tell what the OS is?

    I have an OS on an external drive. Is there any way to tell what version it is without actually booting into it?
    Thanks very much.

    Open Disk Utility, select the disk from the sidebar, and click Info. This won't work for Logical  type volumes; I'm not sure if it works for Windows, but I'm assuming you are talking about OS X on the external drive.

  • How can you tell when the battery is fully charged?

    when done syncing, i have a totally green large battery icon- but thats what i always have- any other indication- or am i misreading the large green battery as an indicator to charge completness?
    the little white battery icon never seems to change when using touch 2g?
    what am i missing please
    thank you very much
    bob donchez

    The small battery symbol has a lightning bolt symbol when the battery is charging and a electrical plug symbol when it is completely charged.
    There are pictures in the users guide, page 27: http://manuals.info.apple.com/enUS/iPod_touch_2.1_UserGuide.pdf

  • HT201328 how can you tell by the phone if it is unlocked?

    i had my iphone unlocked from att i want to know if there ius a way to see if it is unlocked on the phone without having to jhst try another companys sim card.

    After you got unlock approval from AT&T, you were supposed to backup and restore your iPhone in iTunes. Did you see "Congratulation, your iPhone has been unlocked" message after the restore.
    After Restore what does Settings > General > About, Carrier entry say.

  • How can you tell if the Creative Suite application is closing

    Hi,
    Is it possible within a CS extension to know when the host CS application is closing? I have a CS extension for Flash in which I want to know when Flash is closing so I can save a config file being created in the CS extension.
    Thanks
    Stephen

    Hi,
    Is it possible within a CS extension to know when the host CS application is closing? I have a CS extension for Flash in which I want to know when Flash is closing so I can save a config file being created in the CS extension.
    Thanks
    Stephen

  • How can I tell what the iTunes build is before I download?

    I am having difficulty finding out what the iTunes build is for the current download from the Apple site. I am running iTunes 7.6 (29); I assume the "29" is the build for my installed version. I also assume that Software Update will ignore build changes unless the version changes.
    I do not want to download and install the current iTunes build unless it is different from my currently installled app. How can you tell what the specific version and build are from the Apple download site?
    Thanks!

    I am running iTunes on Leopard.

  • How can you tell?

    I just bought a new Airport Extr N which replaced an older G version, I have a new macbook that is N capable too. Nice hah, well how do you tell if the N is working at the max speed? I did install the new Airport Util for the new AE N - what setting and where can you tell if it is working faster then it did at G ? Maybe seems a bit faster, not sure? What is Multicase rate ? currently set to 2 Mbps in wireless options in AE Util ? I do have older G and B Macs on the network. Thanks for your time!

    What is Multicase rate ?
    The Multicast rate tells the base station the minimum data rate at which it should maintain the connection. In other words, if the data rate falls below the multicast setting, the AirPort Extreme base station (AEBS) will break the wireless connection.

  • How can you tell if a pic hasnt been tagged by iPhoto, and do you then...

    How can you tell if a pic hasnt been tagged by iPhoto, and do you then do you then have to draw "missing box" around them
    What I mean is tagged a few faces, imported some more pics, checked a few and they dont show as named faces, but are faces that are in my Faces source list (ie identified and named)
    So do I then have to draw a box around known faces to me, and name them again (I think iPhoto will pop up as Im typing the names I already have)
    It just means that even when i import and it doesnt name, I may have lots of pics that are of faces but not tagged and so not in my faces source list
    please help
    cheers
    ps when are Apple going to upload the Getting Started manuals for iLife 09? its been a while since released now, ad they give a bit more insight than the video tutorials alone

    No-one? It'll be nice to know how many pics of faces that arent yet tagged
    cheers

Maybe you are looking for

  • Multilevel lists in indented text

    Hello everybody, I am using RoboHelp HTML 11 and I have a question regarding the use of multilevel lists in indented text. The main text in my topics is indented by 122.7px in order to leave enough space for text boxes that summarize the main text pa

  • Define Account group with screen Layout (Vendor)

    Hello, Normally, for Intra-Inter company suppliers, we don't apply Withholding Tax. In the customizing of vendor account group, for the group "Inter-Intra company suppliers", witholding Tax informations are suppressed. The problem is i want to change

  • Decalgirl good or bad?

    Hi, I just got my new ipod a few weeks back and ordered a pair of skins and armour from www.decalgirl.com because # Attractive Colours # Protection And a few days later recieved 2 Silicone cases from a company called 4Mac. I have attached links below

  • Having problems connecting an AirPort Express in client mode to a Linksys?

    I have a Linksys WRT150N as my main access point. I recently dumbed down its security to WPA2 Personal so a Dell, and Xbox 360 could get on it wirelessly. Unfortunately, my AirPort Express refuses to connect now even after re-configuring it to use WP

  • Remove Active Tab White Outline Border FF29?

    Hi I would like to remove the white outline border around the active tabs in FF29. I would like it to blend in to the background like the inactive tabs. I have Tab mix plus and classic theme restorer installed. They do fine only would like the border