Airport Extreme Signal S

My iPhone 6 (all 3 of them) are having issues with the internet. They hang up and it is driving us crazy. I have a cable modem (comcast) worked with them on multiple times and even had them come to my house and redo the connections from the house to the poles. But that still did not solve my issue.
I am

Do your iPhones have any issue connecting to other Wi-Fi networks ... just not yours?

Similar Messages

Airport Extreme Signal Weaker than Before

My Airport Extreme signal is weaker than it used to be. Nothing has changed except I can no longer connect to the internet without running diagnostics each time I try to use it. It will connect and then stay connected until my macbook goes to sleep. When it wakes up, I have to re-connect using diagnostics.
I am using it in the same room I always have and never had problems before. But for the past several weeks, it is just not behaving as it always has. I have checked for a firmware update, but airport utility doesn't indicate that one is available. It's running: Version 6.3.2.
Any advice would be greatly appreciated. It's run great for the past several years. This is a new issue...

Because I can no longer connect to the internet without running diagnostics each time I try to use it. It will connect and then stay connected until my macbook goes to sleep. When it wakes up, I have to re-connect using diagnostics.
I am using it in the same room I always have and never had problems before. It will connect without problems in other rooms that are closer to the base station. But from the room where I ordinarily connect, it won't automatically connect anymore.
I can get it to connect from that room, and it will stay connected, but I can only do so by running diagnostics, telling it to assist me and then selecting the network and and following the steps to connect.

I am trying to extend my airport extreme signal to another airport extreme can this be done? I have tried several time using the automated set up but it keeps failing... What am I doing wrong?

I am trying to extend my airport extreme signal to another airport extreme can this be done? I have tried several time using the automated set up but it keeps failing... I have selected every possible security/password encryption level... What am I doing wrong? If it os possible where can I find step by step instructions? Please & Thank you!

The challenge with the older round AirPort Extremes are that they are "g" wireless devices.
When you configure them for WDS, the speed on the wireless network is cut in half...and probably will not have the bandwidth required to stream video reliably from either AirPort Extreme since both are affected by the WDS setup.
There is not an "automated" setup for WDS. You have to do this manually on both AirPort Extremes. Unfortunately, it is not an easy configuration and it's easy to make a mistake and hard to recover without starting all over again.
Apple's instructions for WDS are here if you want to give it a try.
http://support.apple.com/kb/HT4262
It is possible that it might work. Keep us posted on your progress
Adding a single AirPort Express will unfortunately not help. You have to have "n" wireless devices at all router points.

Best way to extend Airport Extreme signal

Like most folks, I had no idea what a poor choice it was to let my internet service providor install my DSL connection in the far corner of my home. So until I install a phone or cable jack in the middle of my place, half my signal is wasted in the back yard, while the other end of my house is out of range.
(iPad 2, iPhone 4S, Macbook, etc)
My question is... what's the best way to extend my Airport Extreme wireless signal? I tried using my Airport Express as an extender but recently read that this actually weakens the signal. If that's wrong, how should I configure them to work?
Does anyone know of a better way to extend my wireless signal to the rest of my house? Short of moving my router?
Thanks in advance!

Please check out the following Apple Support article for details on the various options available to you with using multiple base stations for extending a wireless network. If you have any questions or need further assistance please don't hesitate to post back.

Need helps on weak airport extreme signal

Please bear with me - as I posted here twice
I really need a help, get very tired with this airport extreme card with my brand new Mac Pro.
I bought the machine with bluetooth installed (confirmed that the BT wire connecting with the bluetooth card) and working just fine. I bought the airport extreme card and installed by the shop (there is no apple shop in HK). The IT guy connected only the wire 1 to the card, I questioned whether he needed to connect cables of 1 and 2 together, and he confirmed that only 1 was needed.
Brought the machine home and set up with WiFi with my apple extreme and time capsule (both N), the signal showed a level 4 signal (strongest) but after a minute it dropped to 1 even disappeared despite I placed the time capsule just next to my Mac Pro.
Open the case and connect the cable 2, but it did not show any improvement. Tried the 2 & 3 together - even worst.
Is that a common problem and can't be solved, if so, if I connected the time capsule with Mac Pro via ethernet, would it works? I had tried it but did not work, do I need to do some special setting on time capsule for this connection (Airport extreme (modem) -> time capsule -> Mac Pro (via ethernet)

Have a check of the wiring with the following link
http://web.mac.com/ryemac3/RyeMAC3/Welcome/Entries/2008/4/17Airport_ExpressUpgrade.html
but make sure wire no.3 on top and wire no.1 at the bottom ... cover the wire no.2 with the plastic tube that it came with

Airport loses my network, but not airport extreme signal

Since upgrading to leopard (10.5.1), my wireless network of computers (I am using an imac & mac pro book and a new airport extreme 802.11n base - all of which have worked without problems since networking them 6 months ago), will sometimes not show my own network as a network option in the airport status indicator in the menu bar (this happens sporadically with no apparent regularity). I have 4 bars of airport signal reception and I can even see the networks available around me, but mine will not be there. Usually it will pick it back up if I turn airport off and then reopen it but sometimes I have to restart the whole computer. This doesn't seem to be systemic in that one computer may lose the network while the other is working fine....any ideas. I have seen a lot of postings about wonky airport performance with the new leopard OS, but I couldn't find an answer to this.

Hi, (Sorry this is the first time I've posted on a forum)
I had a similar problem. I had successfully set up a network with 2 window computers, running XP and Vista,and an airport extreme. Works great so long as I don't upgrade the firmware on the basestation to 7.2.1.
Recently I saw the light and purchased an Imac with Leopard and Bootcamp. Couldn't connect to my network. Did recommended changes like turning off IPv6 in the imac's airport utility, and changed the basestation IPv6 mode to local link only. Tried to manually setup DNS server address etc on th imac. Went thru the usual stuff with the Apple helpline. No luck.
Found the only way to connect to the network was to switch off the basestation, get the network diagnostic on the imac to start searching for any networks, then switch back on the basestation. Worked.
Then I read on the forum about trying different radio channels on the basestation, rather than leaving it on the default setting "automatic". I tried Channel 11 and (I guesss it it Xmas!) it works perfectly.
Hope this is of help.

4th Generation Airport Extreme signal is too weak?

I have a 4th generation Airport Extreme and have 2 Apple TVs. The Airport Extreme is tied to my office where I do most of my work and would like to keep it here. The problem is that the signal is not reaching the basement TV and it takes at least 15+ minutes at times to load up movies from my iTunes Library (located on my main floor) to stream to our basement theater. Should I just invest in another Airport Extreme to help carry the signal down to the basement? If so, to save money should I just buy another 4th generation or bite the bullet and get a 5th generation?
Thanks!

Also, can I just buy an Airport Express instead of an Extreme if I am just using it as a repeater?

Boost my airport extreme signal

I have an Airport Extreme but I don't know the model number (is a about a year and a half old) that is in the basement of my townhouse (where the main Mac G5, cable connection and modem is). My son has an iBook G4 in his room 2 floors above and the signal is unstable and keeps dropping out when it comes to that distance and his laptop. Is there Anyway to boost the signal from the Airport so that he can have a stable connection in his room? It works fine when he uses it on the main floor, but is very frustrating for him to sit at his desk and try and stay connected. The cable company says that if I install another modem for an Airport Express to act as a boost then they will charge me for 2 internet lines.
VERY FRUSTRATED and need help.

You can place an AirPort Express (AX) or another AirPort Extreme base station (AEBS) on the first floor. You can then configure that and your existing AEBS to connect wirelessly. The item on the 1st floor will be configured to extend the network provided by the AEBS in the basement.

Airport extreme signal with SDL

Hey guys, My friend has DSL with SBC in california and everything was fin. He just got an airport extreme base station to hook up a box that browse and stream music from Rhapsody (i forgot the name of that box) to play in the speakers around the house but I coudnt set it up properly.
From the DSL modem I went to airport extreme base station to the one with the little symbol, then I went to airport utility and I set up a network with pass for the house, right? after that the three computers in the house and the music box see the new network, so I selected in all of them but neither the computers or the box can go online. I see full signal everywhere but it cannot connect to the network. Also, in airport utility he has version 7.3 and 7.4 was available but everytime I tried to download it didnt do it.
what am I doing wrong?
can anyone please let me know how to finish this for him?
thanks a lot guys!
Edit: his dsl modem is speedstream 5100 from sbc
Message was edited by: demariai
Message was edited by: demariai

demariai wrote:
Hey guys, My friend has DSL with SBC in california and everything was fin. He just got an airport extreme base station to hook up a box that browse and stream music from Rhapsody (i forgot the name of that box) to play in the speakers around the house but I coudnt set it up properly.
From the DSL modem I went to airport extreme base station to the one with the little symbol, then I went to airport utility and I set up a network with pass for the house, right? after that the three computers in the house and the music box see the new network, so I selected in all of them but neither the computers or the box can go online. I see full signal everywhere but it cannot connect to the network.
In AirPort Utility's Internet panel, "Internet Connection" tab, did you set "Connect Using" to "PPPoE" and fill in the login details?

My Airport Extreme Signal output graph is jumping up and down like crazy, is this normal??

The Airport Extreme base station is the 5th Gen, and is about a week old.
All clients and the airport itself aren't moving.
Is this normal? To me it looks really strange. The graph should be smooth line if nothing is moving right?

The biggest problem I see that you will have is that both the 2.4 & especially the 5 GHz radio signals will have a difficult time penetrating through the concrete walls ... so I would suspect only the wireless clients in the same room as the AEBSn will be successful with a wireless connection with sufficient bandwidth.
If one of your network clients is a Mac laptop, you should use iStumbler again to get the signal and noise reading of your AEBSn in both of the rooms that are on the other side of the concrete walls from the AEBSn.
Better still; use iStumbler's Inspector feature (select Edit > Inspector from iStumbler's menu) to determine the Signal-to-Noise Ratio (SNR) at these locations. Within the Inspector, note the values for "signal" & "noise" at these locations. Start with your laptop near the AEBSn, note the readings, and then, choose the locations where where you have each of your wireless clients.
SNR is the signal level (in dBm) minus the noise level (in dBm). For example, a signal level of -53dBm measured near an access point and typical noise level of -90dBm yields a SNR of 37dB, a healthy value for wireless LANs.
SNR Guideline
40dB+ SNR = Excellent signal
25dB to 40dB SNR = Very good signal
15dB to 25dB SNR = Low signal
10dB to 15dB SNR = Very low signal
5dB to 10dB SNR = No signal
If the SNR is 25dB+ at each of these locations, then you should be getting reasonable performance for the wireless client from the AEBSn. If less, try relocating either the AEBSn or the wireless clients until they are within a 25dB SNR range.

AirPort Extreme signal not strong enough

I have an AirPort Extreme. The signal is strong everywhere except in the kitchen, 15 meters but one story below...thick walls, concrete. Can I extend it using a simple Fritz Box (AVM Fritz wireless LAN 300E)?

Yes, follow the directions in KB 107454, AirPort Extreme and Express: Using WDS to create a network from multiple base stations.

How to test strength of airport extreme signal?

We have a 2nd generation Airport Extreme Model Number A11XX as well as a 1st generation Airport Express. We use the Airport Express to connect our iTunes to speakers exclusively. We recently upgraded to 'blazing' speeds of internet (15Mbp up to 30Mbp). Internet speed keeps fluctuating and internet provider has sent 2 people out in the last month since upgrade as well as reprovisioned our modem 3xs AND finally replacing our modem for the second time...all reporting no problem found, though both experiencing the fluctuating signal while here. We have been using Ookla speedtest to keep track of these fluctuations. Charter says that it has to be our wireless router and that they do not support wireless, which is fine, except our problem is not solved. They suggest we plug in directly to the modem via ethernet cable. I would like to know if there is a way to test the signal of our Airport Extreme to see if this is in fact where our problem is coming from.
A few things to note:
DEVICES:
1 iMac, 1 MacBook Pro, 1 Macbook, 1 iPad, 2 iPhones (obviously not all on at the same time....no more than 2 computers at a time)
Never had airport/wifi icon on computer/phone drop below 3 out of 4 bars....usually full strength.
Airport Extreme 2nd generation
Airport Express 1st generation for speakers only
ISSUES:
Experiencing fluctuating internet via WiFi AND directly plugged into modem. go figure.
Fluctuating Speeds from 3Mbp-35Mbp regularly (often timing out because entire signal drops out). And yes, I know the signal won't be at a constant speed always, but such large swings are just not acceptible.
Architect working from home with the need to upload and download large files as well as video conference.
If we need to get a new wireless router that is fine, but we'd rather not since as far as we can tell it seems to be working just fine.
Anyone have any ideas?
Thanks!

What firmware is the AE running??
Factory reset and downgrade the firmware if you are on 7.6.4.. go back to 7.6.1 or 7.5.2
The latest firmware on such an old model is no good.
Factory reset after the downgrade and redo the setup as simple as possible.. use simple names.. this is now important since mavericks which uses SMB networking by default. Names short, no spaces and pure alphanumeric.
Please plug into the AE by ethernet and see if the issue exists over ethernet.. if it all works fine by wired connection and is failing by wireless then basically you have done what is possible and the unit is failing.. replace it.

Airport extreme signal

I don't know if anyone has had this problem ---
but I have a new powerbook with an airport extreme card.
If the computer is near the base station, I get a good signal.I have a widget that gives the strength from 63 - 71, and that is with the computer no more than 12 inches from the router.
When I take the computer down to the basement in a split level house, the signal drops to almost nothing. The signal drop is sudden, not gradual. and doesn't return to full strength until the computer is close to the router.
My daughter, who has a G3 ibook, with the older airport card does not seem to have this problem.
Is is the airport card? Is there something I could do get a good signal throughout the house - or at least in the lower level?
Thanks in advance for suggestions,
nl

I am glad to see there are other people who are having the same problems as I have. My signal on my imac is extremely poor since installing the last airport update. before that i had full 4 bars and fast transmision speeds, now i have one bar and very slow download times. I have moved my base station closer to my computer, but to no avail. this is most definitely somethign to do with the update. is there a way to uninstall it?
I have the same problem. The farther away I am from
my wireless router, the weaker the signal on my
AirPort becomes. The funny thing is that this only
started happening after I downloaded the most recent
airport update last week (11/10/05). Can anyone help?
Apple, can you fix this for us asap? Thanks.

AirPort Extreme signal goes to zero

My AirPort Extreme base station is about 11 months old. Worked flawlessly for several months, then a few months ago it developed a problem in that the wireless signal strength (as seen by an iBook, two PowerBooks and a PowerMac G4 all using Apple cards) sometimes goes to ZERO. No bars, and the network disappears from the menu on all the clients, even the one sitting 10 feet away. Visually, only the center light is on, steady white. The problem is corrected by unplugging/replugging the power cord on the base station.
This sometimes occurs 2-3 times a day, sometimes it does not occur for several days in a row. It has happened in the middle of the day with all users active and it has happened at night with no one active (noticed when the first user tried to connect next morning). The problem may have started with a new level of AirPort software or firmware (we are running the latest available of both, with 3 clients on 10.4.8 and one on 10.3.9) but since the problem is sporadic we didn't associate it with any patch at the time.
The base station is running infrastructure mode, bridging to a wired Ethernet network, so it is not acting as DHCP server. (The wired network clients see no disruption in service when the AirPort goes dead.) 128-bit WEP and access control by MAC address are active.
Any ideas?
PowerMac G4 MDD Mac OS X (10.4.8)

Hmmm, unfortunately, it sounds like the AirPort Extreme card inside your AEBS maybe faulty. Since you already know connecting wired clients to the AEBS is not an issue, would it be possible to remove the AEBS from the current network configuration, and install it as a new standalone wireless network...and then check to see if repeats the drop-outs when wireless clients connect to it? The rationale would be to eliminate any possibility that when it's connected to a wired network may be the cause of the wireless drop-outs.

How to increase Airport Extreme signal strength

I post this in the way of advice, which anyone is free to accept or ignore.
I recently switched to Comcast ("triple play") from an in-complex Ethernet internet system. On my Mac Pro (MP), using speedtest.net, I attained download speeds of at least 22 Mbps. Very fast, I must say. However, I noticed that my Mac Book Pro (MBP) speeds were considerably slower, sometimes only a tenth of those on the MP. I am happy to report that after some reconfiguration I'm attaining almost identical speeds between the MP and MBP. What did I do?
I had initially configured the Airport Extreme (AEx) to operate at 802.11n with 5 Ghz only. Using iStumbler, I discovered that my signal strength was a bit under 60% and the "noise" was 13%. Other wireless devices appearing in the iStumbler window (we live in a downtown apartment complex) showed the "noise" levels at 9%--across the board. I fiddled with the location of my cordless phone (5.4 GHz) and even disconnected it. There was no change in the noise level. I moved the MBP up against the AEx and, while the signal strength increased, upwards of 70%, the noise level remained the same--at 13%.
So, I reconfigured the AEx to 802.11n (b/g compatible). Voila. Not only did the noise drop to 9%, just like the other devices, but the download speeds on the MBP zoomed to around 20 Mbps, or just about the same as the MP.
Too boost the MBP speeds even further I set up an Airport Express (AE) right next to where I use my MBP. I configured it to extend my wireless network.
By the way, I have my MP connected directly to the AEx via Ethernet. The AEx is directly connected to the cable modem. I configured my wireless network as "closed," using interference robustness. I left the multicast rate in default mode, which is 2 Mbps. Transmit power is at 100%.
What I seemed to have learned from this experience is NOT to use the 5 GHz only setting on an AEx, if one wants maximum Internet download speeds. (This seems counterintuitive, I know, because the theoretical limit of 5 GHz is 300 Mbps under 802.11n and "only" 54 Mbps using the 2.5 GHz setting.)

Purchase another Apple AirPort Base Station such as the $99 Express to "wirelessly extend" your AirPort wireless network.

Airport Extreme signal strength problem

My airport extreme's signal is very weak by the time it gets to the other end of my house, and a couple of computers at that end have been using my neighbor's unsecured wifi for their internet connection. How can I extend or strengthen the broadcast? Is there a setting in the airport utility app? The computers affected are windows xp computers. My iMac and Vista pc are connected via the ethernet cable, so they're not using wifi.

Welcome to the discussion area!
Wireless signal strength dissipates quite quickly with distance and any obstructions such as walls or ceilings will make this effect even more noticeable.
If you have a newer dual band AirPort Extreme and you want to extend both bands for greater wireless coverage using wireless only, then you'll need to look at another dual band AirPort Extreme.
The AirPort Express can also be configured to extend your wireless network, but it will only extend one band.
The extending device would normally be located at approximately 1/2 to 2/3 of the distance between your main router and the area that needs more wireless coverage.
Post back if you decide to add an extending device to your network and you need help with configuration details.

Airport Extreme Signal S

Similar Messages

Maybe you are looking for