All of a sudden wireless connection is unstable

Hello there,
Had no problems with BT up until now, I use my wireless connection for things such as the xbox. However, recently (past 2-3 days) the signal strength as indicated by my xbox has been poor/fluctuating constantly resulting in latency and eventually my connection dropping out.
Uptime:
1 day, 0:20:10
Modulation:
G.992.5 annex A
Bandwidth (Up/Down) [kbps/kbps]:
828 / 17,662
Data Transferred (Sent/Received) [MB/GB]:
94.03 / 1.75
Output Power (Up/Down) [dBm]:
12.5 / 23.0
Line Attenuation (Up/Down) [dB]:
11.5 / 25.0
SN Margin (Up/Down) [dB]:
12.5 / 3.0
Vendor ID (Local/Remote):
TMMB / TSTC
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
Loss of Link (Remote):
0
Error Seconds (Local/Remote):
10 / 0
FEC Errors (Up/Down):
326,599,745 / 1,395,235
CRC Errors (Up/Down):
275,650 / 399
HEC Errors (Up/Down):
218,164 / 246
Line Profile:
Fast

There's lots of channels to chose from, try them all.
Aside from that, the hub could be on its last legs.
Or it could be that there's some new source of interference from either something in your home, or a neighbouring property.
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the the reply answers your question then please mark as ’Mark as Accepted Solution’

Similar Messages

  • HP Officejet 6600 e-All-in-O​ne Wireless connection issue.

    We are using the HP 6600 now for 6 months and sice a few weeks we have some issues with the printer.
    situation:
    1 - HP 6600 printer
    1 - Wireless Router
    3 - Computers connected to the router
    What we did:
    Updated the firmware
    Manual IP
    Put channel from router to 11
    Put it closer to the router (1 meter instead of 3)
    HP docter, everything is fine (if connection is lost, answer "No network connection to your device"
    But all above is not the solution.
    When the printer is offline we just switch it off and on and it will work again for a couple of hours. It looks that the connection is lost when it is going to sleep/hybernate.
    Also one of my customers has exactly the same problem, also did all above and didnt fix anything. This question is for me quite urgent because i am going on holidays in 2 days, my father in LAW cannot work without the printer and is getting upset this all this.
    Any advices?

    Arjan_NL
    If I understand you correctly the printers blue light is flashing and you cannot see your printer on the network. I recommend that you reset the network defaults to factory settings on the printer.
    To reset the network defaults
    -touch Setup Menu
    -touch Network
    -touch Restore Network Defaults
    Then use the Wireless Setup Wizard to connect the printer to the network.
    To run wireless setup
    -touch Setup
    -touch Network
    -touch Wireless Setup Wizard
    follow the on screen instructions to set the printer up on the network. You will need the WPA password or security key for the router to do this.
    Follow the steps in this document Printer Does Not Maintain Wireless Connection to set a static IP address for the printer. This should help you maintain a better wireless connection.
    Keep me posted and let me know if you need further assistance.
    I worked on behalf of HP.

  • All of a sudden no connection

    Hi. I use a 12" powerbook on an Airport Express everyday. It works fine. Today, I opened up the computer and there is full strength, but I cannot connect to the internet. No pages come up, e-mail won't connect, etc. If i take it down to another connection, it works great. Other computers work fine on the Base Station, except my laptop. So, bottom line:
    My computer all of a sudden stopped working with the base station, despite reading full signal and being able to view it in Airport Admin Utility.
    It works with other networks.
    Other machines work with the base station, as well as other networks (as they should).
    Anyone have any input? Any would be very much appreciated.
    Thanks

    How would I go about releasing and renewing the IP? I
    tried using the same settings as this laptop I'm
    using, but that obviously doesn't work.
    System Preferences > Network > Airport > TCP/IP
    Change from DHCP to Manual, click Apply.
    Wait
    Change from Manual to DHCP, click Apply.
    Wait.
    iFelix

  • All of a sudden no connection to any device?

    I hooked up my wireless router on Sunday and it's been working like a gem. However today, I decided to link my laptop to it only to find that the whole connection was gone. My iPod's connection wasn't available either.
    I am very illiterate when it comes to this kind of stuff, so ask me what you need to know.
    Thank you

    What is the model of your Linksys router?
    If you have the Linksys E series (E1000, E2000, E3000, E4200,E1200,E3200) all you have to do is download the correct Setup wizard for your device on  your computer. to learn how to download click here.
    The next thing you will do is reconfigure your router. But first reset your router for 10 seconds. to do this just press and hold the reset button, it is located either at the bottom or at the back of your router. This will delete all the previous settings. If you have installed Cisco Connect make sure to uninstall it first from your computer.
    After you reset the router and uninstall the Cisco Connect software (if you have one) run the setup wizard that you recently downloaded. Follow the onscreen instruction.

  • Apple TV all of a sudden cannot connect to Wifi

    My apple tv just stopped being able to connect to my wifi.  It locates it and all of my other devices, both apple and PC are connected to the Wifi and streaming without a problem.  I've restarted and tried to restore, troubleshoot, disconnect, try another wifi....etc.   i see a lot of similar issues on the discussion boards but no responses from someone that has a resolution.  I am in Buenos Aires and have been for over a month...it has worked fine up until today.  There are no apple dealers in BA so i'm out of luck if i can't get this to work.
    it all started with my apple tv not being able to set the date and time....i'm assuming because it couldn't connect to the wifi.  I don't have an option to connect via ethernet either as it's a community router in the building.
    Any possible reason for this...resolutions?
    Thanks for everyone's help

    Mine just started doing exactly the same. I'm in Tokyo and the house is wired for technology: thr router, airports, computers, ipads, iphones are all working absolutely fine. One minute I was watching Dexter the next asks for my password for network right out of the blue. Then says "Cannot connect to network" and gives and error -6, whatever the devil that is.
    Really annoying..nothing else wrong with my network as I say, and I haven't updated any firmware in airport etc to disturb what was a perfect status quo. Really really annoying....wish I could do something other than share your pain Bitta Panda....but I've tried resetting everything as well - apple tv included.

  • Why is my iphone 4 all of the sudden not connecting to wifi?

    My husband and I both have an iphone 4 and as of yesterday both phones have randomly stopped connecting to any wireless network. The networks show up, I have passwords in the phone for them, but the circle next to them just spins and spins.  Occasionally it connects for a few seconds, then it disconnects.  We've done nothing to change the router.  I've tried "reset network settings", I've reset the router and tried turning the phone on and off.  Nothing has worked!  We have not upgraded to ios 7.0.3 because we heard that it doesn't perform well with the iphone 4.  Is that the problem?  Both phones worked just fine until yesterday.  I would appreciate any advice

    Sounds too coincidental to have both phones go bad at once on the same day.
    It could still be your router, even if you have reset it.
    Have you tried connecting to another WIFI network, like a public WIFI or neighbor's?

  • My internet will all of a sudden not connect to Firefox, but it will connect to Internet Explorer. What's wrong?

    I tried to load a few websites on my Firefox browser, but it said it was "Unable to connect." I then tried to load the same websites on my Internet Explorer website and it connected fine. I'm not sure why this is happening.

    With the home page on display, in the menus select View, then Zoom and then Reset
    For details on the zoom features see [[page zoom]] and [[text zoom]]

  • Wireless connection unstable on Leopard

    Hi, I just got a new iMac as part of a free upgrade because my local store could not seem to fully repair my previous iMac and I am having issues staying connected to the internet while using Leopard.
    Everything usually starts off fine but it seems that if I'm on my online game for 30-45mins the internet will suddenly disconnect. When I go to the list to view my available networks they are all missing for several seconds before reappearing and the computer automatically reconnects itself to my network only to disconnect another 10-15 min later and repeats the process. I've only had this computer for a few days and have managed to keep a stable connection of several hours only 2-3 times.
    Before when having initial connection set up issues there seemed to be a problem with a driver that was easily fixed when uninstalled and the computer restarted. My only theory is that the computer may be over heating causing it to loose the ability to see my router but I don't know if there is a way to improve fan efficiency while using Leopard.
    Please help me out.

    Hello Tigerhawk,
    While I am not an expert on Apple Wireless, I may be able to offer you some general advice and perhaps narrow down your problem description.
    From what you wrote, I deduce as follows:
    - On your old iMac, you also used wireless and never saw this issue. In other words, your current issue was introduced with the installation of your new iMac?
    - You are still using the same Access Point?
    - Your iMac is bootcamped and you first experienced the issue on the non OS-X system.
    - Later, when using OS-X, you experienced the same issue.
    Just a few more questions to get things into perspective:
    - You are using 10.5.3 (I suppose). Given this is a recent update, you also saw the issue on 10.5.2?
    - If there are other people in your household, do they suffer the same issue?
    - Are you using 802.11n (Airport Extreme)?
    - What brand is your Access Point?
    - If all wireless items are Apple branded, are you using 802.11n only, or 802.11b/g?
    - Are you using encryption? If so, what type? WEP? WPA/WPA2-Personal/Enterprise?
    Lately I installed Airport Extreme on my own Mac and found the connection to be sluggish and would sometimes loose connection or experience signal deterioration. While installing the base station (Airport Extreme), I pretty much went the default way with the base station in Bridge mode.
    I found that giving the base station a fixed IP address (instead of the default DHCP) and also manually configuring the DNS addresses made the wireless experience a lot better. Of course, this could be an isolated incident. Before I gave my Macbook (10.5.2 at that time) to my girlfriend, I also noticed irratic connection stability. But that was on a non Apple branded Access Point, so not a fair comparison. This Macbook is in her house, so I cannot test at the moment. As another comparison, the iMac in my GF's house (latest generation May 2008) is just screaming fast using an Airport Extreme base station. I did not observe dropping of connection. The Macbook still did drop connection, even when on the Apple Base station. Wired it is very fast and she's happy with that for the moment
    You can try perhaps as follows for testing purposes:
    - Remove all security from your wireless connection (open system).
    - If that improves the situation, move to WEP.
    - If that this works fine, move to WPA and observe.
    - If all of the above do not change your experience, you may try the manual configuration I mentioned earlier.
    Hope this helps in any way.
    Best regards,
    Eirram

  • IMac and other Apple devices lose wireless connections

    We have two Apple iMacs, a MacBook Pro, an iPad and iPad2 and they all intermittently lose their Wireless connection to my network.  All of my PC's work just fine and stay connected.  This is funny... the MacBook Pro booted to Windows 7 Pro stays connected, but the MacOS doesn't.
    It appears to be a problem with DNS, because if you ping to a remote host, you get a response back.  Also, if you put an IP address into Safari on the iMac and MacBook then a site will come online.  However, the iPads just say "You are not connected" while in Safari.  I have verified that I'm using the correct DNS addresses provided by my ISP, and I have a Windows Domain server running DHCP/DNS on the inside of my firewall.
    We recently moved and were issued a new wireless router by our ISP.  I was thinking that might be the problem, but then we don't have the problem with any of the Windows PCs.  This router is manufactured by Arris.  My other router was a Cisco that worked like a champ.
    Turning off the Airport feature and turning it back on restores Web Browsing capability.  Interestingly, if I have a remote desktop session running, it never gets disconnected even when the web stops working.  Again, symptoms point to DNS issues.

    If you feel it's DNS related then change the DNS setting to:
    1. System preferences
    2. Network
    3. Click Advanced
    4. Click DNS tab
    5. Click + sign
    6. Add 208.67.222.222
    7. Click + sign
    8. Add 208.67.220.220
    9. Click OK.
    10. Exit System Preferences

  • E4200 - constantly getting drop wireless connection

    First, if you only plan on using the ports on the back for network connections, I have had no problems. My issues are all deal with the wireless connections. I am constantly getting dropped and when I called Cisco/Linksys support, I was told that I needed to turn off my wireless N and have all the devices connect at a slower speed.

    First of all please verify that you have got a 802.11n card in your computer. New generation routers (i.e. E4200) speaks an entirely different language than 802.11g cards, so while those adapters can work with the E4200 for example, they are not optimized to work with it. It is like having to translate from one language to another in real time when going from N to G... So in those cases the old router will show a stronger signal than the new one.
    SECOND, make sure the adapter driver is up to date.
    Try to do the following steps:
    A] With the help of Cisco Connect Software (if at all you have installed the router with the help of this software)
              1] Open the software and go to the option which says "Router Settings"
              2] Then click on the option which says "Advanced Settings" which will take you to the router's configuration page.
             3] Then go to the Wireless tab, keep network mode as mixed,
     For Channel Settings of 2.4 GHz you can make Channel Width to 20 MHz only and Channel to 6, 9, 11..
     For Channel Settings of 5 GHz you can make Channel Width to 20 MHz only and Channel to 40 or 161...
    B] If you haven't installed Cisco Connect then you can log on to the router's user interface using it's default IP address in the browser which is 192.168.1.1 and type in 'admin' as the password leaving the username field blank. This will take you to the router's web interface and then follow steps as mentioned above to make the changes.

  • Does anyone who owns a 2011 Mac Pro 17' also has a weak-wireless connections from the router? Seek for the solutions

    Hi, I have just brought the 17' Mac book Pro two months ago. However, I found out that this new laptop's wireless connection is unstable. Compare with my 2010 13' Mac Pro  and ipad2, the result is significantly responsible with the new wireless card model.(Correct me if I am wrong)
    Hence, I am looking for a solution because I frequently skype with my oversea family members. I appreciate for your time and help
    Thanks
    Hahaq

    "...Office Depot is the store where they are on sale. A 15% fee is not fair in my opinion..."
    Is that the store policy on returns? What about buying from Best Buy?

  • I am new to IPod touch and really enjoying it.  BUT.  All of a sudden I am unable to connect to my home wireless network nor any hot spots.  Did not have any trouble in 1st month and yet something seems to have changed.  Any suggestions as to what ?

    I am new to IPod Touch and enjoying but all of a sudden (after about a month of connection) I am unable to connect to either my home wirless or hotspots outside of home.  It would appear that a setting has changed but have no idea how to determine.  Any suggestions ?

    NO I did not and thank you very much for the advice.  My problem was stated incorrectly in that while I am able to connect to the wireless from that point on I am unable to connect to the internet.  I will check the article referred to.

  • I have a MacBook Pro and all of a sudden  I cannot get wireless internet connectivity to my router or any other router, I get connectivity through the ethernet port but not wireless. This was working well till this morning

    I  have a MacBook Pro and all of a sudden  I cannot get wireless internet connectivity to my router or any other router, I get connectivity through the ethernet port but not wireless. This was working well till this morning

    BXB1905 wrote:
    I tried the Apple diagnostics it did not work.
    What do you mean it did not work!  What were the results of the diagnostic tests?
    Have you contacted your ISP to determine if the problem is on their end?  
    Have you changed your router channel?  Sometimes this resolves wireless problems.
    Your profile confirms you are using Lion.  Check out the following: 
    Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6
    Configuring 802.1X in Mac OS X Lion and Later

  • HT1860 my apple tv (1st gen) has worked fine for a year/ All of a sudden it has stopped displaying any movies or tv. It only displays my movies or my tv that has been previously down loaded. however it appears connected wirelessly with good strenght. Any

    my apple tv (1st gen) has worked fine for a year/ All of a sudden it has stopped displaying any movies or tv. It only displays my movies or my tv that has been previously down loaded. however it appears connected wirelessly with good signal strength. Have tired swithing off both router and apple TV. Any ideas?

    This is a known, ans ongoing issue. Rest assured you're not the only one affected. There are several threads here already discussing this, I suggest searhing them out if you want more details, and possible work-arounds for locally hosted content.

  • 1 PC out of 5 cannot all of a sudden connect to the wireless router

    We are using the Actiontec MI424WR-GEN2 Rev E router. We've had up to 8 devices connected, working perfectly for over a month. Now all of a sudden my wireless desktop will not connect to the router will all the other devices still connect and access the internet with no problem what so ever. Checked to make sure no viruses or malware. I do use bitcomet on this desktop which is a P2P torrent software. Anyone have any ideas??

    Are you forwarding ports? Has the router been reset? Check firewall or the security you are running on that pc.
    Joe D
    Verizon Telecom
    Fiber Solution Center
    Notice: Content posted by Verizon employees is meant to be informational and does not supercede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or Plan.Follow us on Twitter™!

Maybe you are looking for

  • Keep Getting Error Code 4450

    I ran a diagnostic, here it is! I have burned 4 other CD's and now I'm having trouble...any help would be HUGELY APPRECIATED!! thanks, Amy Microsoft Windows XP Home Edition Service Pack 2 (Build 2600) Dell Computer Corporation Dimension 4600i iTunes

  • I see the other libraries but don't get the "import" ribbon and buttom at the bottom

    I just added a new computer to the homesharing and while I see the other libraries, I don't get the ribbon at the bottom that has the import button. This is only happening on the new system. How can I get the ribbon to come up

  • Why dont I have settings and Utilities in my "Tool...

    hi, For some reason I dont have settings and utilities in my tools menu? Does anyone know why or how I can fix this? There is so much i cant do without it. I have tried updating my n96 through my pc with the nokia updater software but it keeps saying

  • Caveman with club defeats ALL .mac and idisk problems!

    Well, I'm pretty proud of myself. Like many others after upgrading to Leopard, had myriad .mac and idisk problems including, but not limited to: couldn't mount idisk on desktop, can't enable syncing of .mac on various computers, couldn't register a c

  • How to retrive table names with Java?

    Hello! If I connect to my Oracle Database 10g Express Edition Instance with some Java code and I run the following code:                ResultSet resultSet = databaseMetaData.getTables(null, null, "%", types);                while( resultSet.next() )