Anyconnect Client with IOS Webvpn - Multiple Installs

Has anyone worked out how to install multiple anyconnect packages (to support different versions)? When I do a webvpn svc install it overwrites the existing platform, and we need to support all of the different platform types. Many thanks

I just figured out the answer.'
I had a 2.5.60005 version installed on my ASA with Windows NT running.
I wanted to upgrade to the latest version of the Cisco Secure Mobility Client.
I put the anyconnect-win-3.1.03203 package at the top, but I did not add the regular expression, and presto.
I was still able to connect with the win-2.5.6005 anyconnect.
I even removed the regular expression from the 6005 image and was still able to establish a connection.
**NOTE** - I was not able to browse to the portal and click start anyConnect with the 6005 image still on my machine, but I was able to open up the client and connect directly. When I uninstalled the client, and connected to the portal and clicked on start anyconnect, it installed the latest client.
Please rate helpful post and mark this question as answered.
Thanks,
Alex

Similar Messages

Anyconnect clients with intermittant timeout/high MS

I'm having a problem where some clients are pinging servers on my lan just fine, but every so often it hangs with about 2500-3000ms then continues just fine for another 30-40 pings. If I connect with another machine running the same version of Anyconnect (the latest version) it pings consistenty.
Noticing a lot of strange issues with Anyconnect recently - is there any server side logging that can be enabled to gain more insight on what's going on with specific clients? I had to reboot another ASA earlier today to remedy a problem where some new clients could connect but couldn't ping anything...while others would work like nothing was wrong...connecting/disconnecting like usual.
Thanks in advance

Hi,
I wil be difficult to figure out exactly what is going on without a TAC case but here are a couple of pointers that might help you to see what is going on:
1.) Filtered buffered logs on the ASA itself.
To verify if the traffic is dropped on the ASA or not, you can setup buffered logging:
logging buffer-size
logging buffered debugging
logging on
Then, check the IP address which is assigned to your AnyConnect client which is unable to pass traffic and check the entries related to it in the logs:
show logging | i
2.) Check the statistics of the AnyConnect session on the ASA
This command will show you a couple of counters related to your session and might give you a hint of what is wrong:
show vpn-sessiondb detail svc filter a-ipaddress
You can replace a-ipaddress by p-ipaddress or name if you want to filter on public IP of the client or username.
3.) Logs generated by the AnyConnect client itself
If you launch the event viewer from a Windows host where AnyConnect is installed ("eventvwr" command), you'll see that there is a new log type named "Cisco AnyConnect VPN Client". The client will write in there all the logs related to your connection.
If you are using Linux, the logs will either be stored under /var/log/messages or /var/log/syslog.
For OSX, it would be /var/log/system.log.
If you still don't see where the issue is after those steps. my advise would be to open a TAC case to have the issue investigated.
Regards,
Nicolas

SSL VPN (WebVPN) issues with IOS 15.0(1)M1

Hello everyone... I need your help!
I am having some weird issues with webvpn/anyconnect, please find the relevant information below;
Symptoms:
- AnyConnect Client prompts users with the following error:
"The secure gateway has rejected the agent's VPN connect or reconnect request. A new connection requires re-authentication and must be started manually. Please contact your network administrator if this problem persists."
Debug:
Mar 5 13:09:45:
Mar 5 13:09:45: WV-TUNL: Tunnel CSTP Version recv use 1
Mar 5 13:09:45: WV-TUNL: Allocating tunl_info
Mar 5 13:09:45: WV-TUNL: Allocating stc_config
Mar 5 13:09:45: Inserting static route: 172.25.130.126 255.255.255.255 SSLVPN-VIF36 to routing table
Mar 5 13:09:45: WV-TUNL: Use frame IP addr (172.25.130.126) netmask (255.255.255.255)
Mar 5 13:09:45: WV-TUNL: Tunnel entry create failed:IP= 172.25.130.126 vrf=77 session=0x67234340
Mar 5 13:09:45: HTTP/1.1 401 Unauthorized
Mar 5 13:09:45:
Mar 5 13:09:45:
Mar 5 13:09:45:
Mar 5 13:09:45: Deleting static route: 172.25.130.126 255.255.255.255 SSLVPN-VIF36 from routing table
Mar 5 13:09:45: WV-TUNL: Failed to install (addr 172.25.130.126, table_id 77) to TCP
Mar 5 13:09:45: WV-TUNL*: Received server IP packet 0x6692EB08:
Mar 5 13:09:45: WV-TUNL: CSTP Message frame received from user usr-test (172.25.130.126)
WV-TUNL:      Severity ERROR Type USER_LOGOUT
WV-TUNL:      Text: HTTP response contained an HTTP error code.
Mar 5 13:09:45: WV-TUNL: Call user logout function
Mar 5 13:09:45: WV-TUNL: Clean-up tunnel session (usr-test)
When the error occurs, the "SVCIP install TCP failed" counter increments:
VPN-Router1# show webvpn stats detail context CUSTOMER-VPN
[snip]
Tunnel Statistics:
    Active connections       : 1
    Peak connections         : 3          Peak time                : 19:09:04
    Connect succeed          : 9          Connect failed           : 5
    Reconnect succeed        : 0          Reconnect failed         : 0
    SVCIP install IOS succeed: 14         SVCIP install IOS failed : 0
    SVCIP clear IOS succeed : 18         SVCIP clear IOS failed   : 0
    SVCIP install TCP succeed: 9          SVCIP install TCP failed : 5
    DPD timeout              : 0
[snip]
IOS Version Details:
Cisco IOS Software, 7200 Software (C7200-ADVIPSERVICESK9-M), Version 15.0(1)M1, RELEASE SOFTWARE (fc1)
System image file is "disk2:c7200-advipservicesk9-mz.150-1.M1.bin"
The router also runs IPSEC remote access VPN in addition to the webvpn/anyconnect scheme.
Config:
webvpn context CUSTOMER-VPN
title "SSL VPN for Customer"
ssl authenticate verify all
login-message "Enter username and passcode"
policy group CUSTOMER-VPN
   functions svc-required
   svc keep-client-installed
   svc split include 10.1.16.0 255.255.240.0
   svc split include 10.1.2.0 255.255.254.0
vrf-name CUSTOMER-VPN
default-group-policy CUSTOMER-VPN
aaa authentication list AAA-LIST
aaa authentication auto
aaa accounting list AAA-LIST
gateway vpn virtual-host customer.xx.com
logging enable
inservice
The error happens sporadically, at least once a week, and on different contexts. Does anyone have any clue on what can cause this issue? Any help is appreciated!

Have you seen my post https://supportforums.cisco.com/message/2016069#2016069 ?
At that point in time we were running with local pool definition.
As the http 401 rc happens very sporadically we still gathering incident reports internally.
Will open a case if you did not yet.
cheers, Andy

SSLVPN with iPhone Anyconnect and Cisco IOS Router, Certificate Authentication failed

Hello,
i have a problem regarding the authentication with a certificate from the iPhone Anyconnect 2.5 Client to a 1802 Cisco Router.
Cisco 1802 Router:
Cisco IOS Software, C180X Software (C180X-ADVENTERPRISEK9-M), Version 15.1(1)T, RELEASE SOFTWARE (fc1)
First i configured SSLVPN with username and password, in this configuration the Anyconnect Client of my iPhone works.
then i enrolled a certificate from my Windows 2008 R2 CA to the Router with the Attributes: Server Authentication and IPSEC
and i enrolled a certificate for my iPhone with Client Authentication and IPSEC
after a bunch of time ( i realy could not find a really good documentation on how to do this) i got it done, in the webvpn context configuration i made this changes here:
no aaa authentication list default
authentication certificate
ca trustpoint CA
as the "SSL VPN Configuration Guide, Cisco IOS Release 15.1M&T" says: if i want only certificate authentication i had to user the "authentication certificate" command and thats it.
as i look into the debugs it seems to me that the Router accepts the certificate of the iPhone, but then i receive a window on the iphone that wants an additional username and password authentication, and no matter what i enter there's always the same dialog coming back..
any ideas what the problem could be???
here is the configuration:
webvpn gateway WEBVPN_GW_OFFICE2
ip interface Dialer0 port 1444
ssl trustpoint CA
inservice
webvpn install svc flash:/webvpn/sslclient-win-1.1.4.179.pkg sequence 1
webvpn install svc flash:/webvpn/anyconnect-win-3.0.4235-k9.pkg sequence 2
webvpn install svc flash:/webvpn/anyconnect-dart-win-2.5.3055-k9.pkg sequence 3
webvpn context WEBVPN_CONTEXT2
secondary-color white
title-color #669999
text-color black
ssl authenticate verify all
policy group WEBVPN_POLICY2
   functions svc-enabled
   mask-urls
   svc address-pool "SSLVPN_OFFICE1"
   svc default-domain "domain.internal"
   svc keep-client-installed
   svc split include 192.168.0.0 255.255.0.0
   svc dns-server primary 192.168.53.33
   svc dns-server secondary 192.168.53.35
virtual-template 3
default-group-policy WEBVPN_POLICY2
gateway WEBVPN_GW_OFFICE2
authentication certificate
ca trustpoint CA
inservice
here is the debug:
OfficeRouter1# PASSING appctx is [0x89FAFFCC]
Nov 19 22:39:53.507: WV: sslvpn process rcvd context queue event
Nov 19 22:39:53.507: WV: sslvpn process rcvd context queue event
Nov 19 22:39:53.607: WV: sslvpn process rcvd context queue event
Nov 19 22:39:53.607: WV: Entering APPL with Context: 0x86529380,
      Data buffer(buffer: 0x86543A40, data: 0x15A07AB8, len: 469,
      offset: 0, domain: 0)
Nov 19 22:39:53.607: WV: http request: / with no cookie
Nov 19 22:39:53.607: WV: validated_tp : CA cert_username : matched_ctx :
Nov 19 22:39:53.607: WV: Received appinfo
validated_tp : CA, matched_ctx : ,cert_username :
Nov 19 22:39:53.607: WV: Trustpoint match successful
Nov 19 22:39:53.607: WV: Extracted username: pass: ?
Nov 19 22:39:53.607: WV: Client side Chunk data written..
buffer=0x86543640 total_len=661 bytes=661 tcb=0x8811FE60
Nov 19 22:39:53.607: WV: Appl. processing Failed : 2
Nov 19 22:39:53.607: WV: sslvpn process rcvd context queue event
BueroRouter1# PASSING appctx is [0x89FAEEC4]
Nov 19 22:40:24.028: WV: sslvpn process rcvd context queue event
Nov 19 22:40:24.032: WV: sslvpn process rcvd context queue event
Nov 19 22:40:24.132: WV: sslvpn process rcvd context queue event
Nov 19 22:40:24.132: WV: Entering APPL with Context: 0x86529380,
      Data buffer(buffer: 0x86543A40, data: 0x160C4038, len: 469,
      offset: 0, domain: 0)
Nov 19 22:40:24.132: WV: http request: / with no cookie
Nov 19 22:40:24.132: WV: validated_tp : CA cert_username : matched_ctx :
Nov 19 22:40:24.132: WV: Received appinfo
validated_tp : CA, matched_ctx : ,cert_username :
Nov 19 22:40:24.132: WV: Trustpoint match successful
Nov 19 22:40:24.132: WV: Extracted username: pass: ?
Nov 19 22:40:24.132: WV: Client side Chunk data written..
buffer=0x86543640 total_len=661 bytes=661 tcb=0x88D11EEC
Nov 19 22:40:24.136: WV: Appl. processing Failed : 2
Nov 19 22:40:24.136: WV: sslvpn process rcvd context queue event
Nov 19 22:40:39.764: WV: sslvpn process rcvd context queue event
Nov 19 22:40:39.880: WV: sslvpn process rcvd context queue event
Nov 19 22:40:39.892: WV: sslvpn process rcvd context queue event
Nov 19 22:40:39.892: WV: Entering APPL with Context: 0x86529380,
      Data buffer(buffer: 0x86543A40, data: 0x1616FD38, len: 610,
      offset: 0, domain: 0)
Nov 19 22:40:39.892: WV: http request: /webvpn.html with domain cookie
Nov 19 22:40:39.892: WV: validated_tp : cert_username : matched_ctx :
Nov 19 22:40:39.892: WV: Received appinfo
validated_tp : CA, matched_ctx : ,cert_username :
Nov 19 22:40:39.892: WV: Trustpoint match successful
Nov 19 22:40:39.892: WV: Client side Chunk data written..
buffer=0x86543640 total_len=607 bytes=607 tcb=0x88D11EEC
Nov 19 22:40:39.892: WV: Appl. processing Failed : 2
Nov 19 22:40:39.892: WV: sslvpn process rcvd context queue event

http://www.cisco.com/en/US/products/ps8411/products_qanda_item09186a00809aec31.shtml
HI,
Refer to
AnyConnect VPN Client FAQ
Q. Is it possible to connect the iPad, iPod, or iPhone AnyConnect VPN Client to a Cisco IOS router?
A. No. It is not possible to connect the iPad, iPod, or iPhone AnyConnect VPN Client to a Cisco IOS router. AnyConnect on iPad/iPhone can connect only to an ASA that runs version 8.0(3).1 or later. Cisco IOS is not supported by the AnyConnect VPN Client for Apple iOS. For more information, refer to the Security Appliances and Software Supported section of the Release Notes for Cisco AnyConnect Secure Mobility Client 2.4, Apple iOS 4.2 and 4.3.

Anyconnect client installer

Anyone have an issue with the anyconnect client installer that after the install it does make a successful connection but the anyconnect installer window says it failed? Is this a bug?

Well if it works, it must have installed adequately, error messages notwithstanding.
There are a couple of installer bugs documented. I've not run into nay of them personally.
What version and client OS are you installing?

How do you get multiple screens on the iPad with iOS 5.1.1?

How do you get multiple screens on the iPad with iOS 5.1.1? We just upgraded to iOS 5.1.1, and we see no way to be able to open multiple screens at once. Before, there was a small button in the upper portion of any window. That button would take you from a particular window to the place where multiple windows are open at once. Does it do it differently? Is there a special setting button that we have missed? Thanks!
One more thing: We are only talking about Safari.

Guitaristica-
I don't think I've seen a way to have separate Safari screens visible at the same time. The small thumbnails were deleted in one of the iOS updates, and replaced with a multiple "Tab" system.
You can open an additional screen in a new "tab" by pressing and holding on a link until a new menu comes up.
Fred

Windows 8.1 Preview not working with AnyConnect Client

I had Windows 8 and was running Cisco AnyConnect client 3.0.10055 perfectly.
I upgraded to the Windows 8.1 preview and it tries to download update and then it fails and disconnects with the following message:
An unknown termination error occurred in the client.
Tried uninstalling and reinstalling the client, no luck.
Any ideas?
Thanks,
Eric

I had the same issue with windows 8.1 x64. I believe there is an issue with the windows 8.1 update process where it fails to update some of the drivers properly. I have noticed this issue with other windows drivers after the update. Follow the steps below and you VPN should work again.
1. Uninstall Cisco Anyconnect client.
2. Go to Device Manager and Disable Cisco AnyConnect VPN Virtual Miniport Adapter for Windows x64
3. Go to C:\Windows\System32 and rename vpnva64.sys to vpnva64_Old.sys.
4. Reinstall Cisco Anyconnect client.
5. Go to Device Manager, you see duplicated Cisco AnyConnect VPN Virtual Adapters. Uninstall one of them but do not check the option to remove the driver.
6. Apply the registry fix in this blog: http://www.tomontech.com/2012/03/pro-tip-cisco-anyconnect-vpn-client-and-windows-8-consumer-preview/
7. Try to connect again and your Cisco VPN should work.

How to handle multiple clients with DatagramSocket

I am trying to handle multiple clients with 1 datagramSocket bind to one port (basically I have only one port to use, and I can not use TCP or any other ports). At the server side I have two threads one for receiving packets and buffering them, another for processing the packets in the buffer and sending replies.
I can have multiple clients sending datagramPackets to me and I will have to process the packets and send them to DIFFERENT clients. Ex. Client 1 sends datagramPacket to Server which sends the processed packet to Client 2. Also Client 2 sends a datagramPacket to Server which again processes the packet and sends it to Client1. May have Client 3 and 4 doing the same thing at the same time... and so on...
My root class is creating the datagramSocket(somePort) and two threads (receiver and sender). How can I use the socket that I created in these two threads??
I have done the following and I am getting "java.net.bindexception". When I am sending stuff from Client1 to Client2 everything is fine but when I start sending something from Client2 to Client 1, I get the bindexception... Client 1 is using port 3000, Client 2 is using port 4000.
I really don't have a lot of experience in socket programming so I am not sure if there is a much simpler way to do this. I appreciate all the tips and help that I can get...
Thanks...
class UDP_serv
     static DatagramSocket udpSocket;
     final static int SERVER_PORT     = 2000;
     public static void main(String[] args) throws SocketException
          udpSocket= new DatagramSocket(SERVER_PORT);
          new DataReceiver().start ();
          new DataSender().start ();
     static class DataReceiver extends Thread
          DataReceiver()
               Thread.currentThread().setName("DataReceiver");
          public void run()
               while (true)
                    byte pckt[] = new byte [MaxMsgSize];
                    DatagramPacket dp = new DatagramPacket (pckt, pckt.length);
                    try
                         udpSocket.receive (dp);
                         //PUSH TO RECEIVE BUFFER
                    catch(Exception e)
                         e.printStackTrace();
     static class DataSender extends Thread
          DataSender()
               Thread.currentThread().setName("DataSender");
          public void run()
               while (true)
                    processDataMsg();
      static void processDataMsg()
         DatagramPacket op;
         InetAddress DA = null;
         int DP = 0;
         byte [] outPacket = null;
         // POP FROM RECEIVE BUFFER
         // SOME PROCESSING HERE
         // Set Destination Address (DA)
         // Set Destination Port (DP)
         // DA and DP are the forwarding IP and Port addresses
         // not the addresses original packet was sent from.
         try
          op = new DatagramPacket (outPacket, outPacket.length,DA, DP);
          udpSocket.send(op);
         catch (IOException e)
          e.printStackTrace();
}Also for development and testing purposes, I am running the two clients and the server on the same machine (windows xp-32b) so all of the Destination IP Addresses are 127.0.0.1. and as I said Ports that I am using are 2000, 3000, 4000 (Server, Client1, Client2).

Hmm I have minimized the code and it seems to be working now.
I think I have an error in the header portion of the data I am sending, where I am storing the source IP/Port and destination IP/Port. I think the server in the middle is messing these values up while sending them to the destination Client. Because the destination client actually receives the stuff and sends the reply back to the server, but the reply packet's headers has 0/0 as the dest IP / Port...
Server is giving me java.net.BindException: Cannot assign requested address error when it tries to forward the reply it received from the client2 as the address it is trying to send is 0!
I guess it doesnt just give this error when you try to open two sockets to the same port...
Paul, Thanks for the direction on how to proceed... took me a while get the minimized code but at least figured out the problem. Well still have to make sure that is THE problem though :)
As far as the statics goes how can I change those to non static ones? Where do I make an instance of the top level class that creates the threads? and how do I pass the DatagramSocket to the threads/ if I dont need to pass how do I call or use the datagramSocket I created in the top level class? I mean do I still kinda have it like a global variable on the top?? A very simple example would be much appreciated...
I think these might be really basic questions but I am having a rough time with the hierarchy in java...

ISE 1.2 Posture Assessment with AnyConnect Client

Hi Experts,
I need clarity for posture assessment with AnyConnect client. I understood that we had traditional NAC agent with ISE 1.1.
Since new Anyconnect version 4 has come which is used for ISE 1.3 posture assessment however I am not sure if I can use Anyconnect 4 with ISE 1.2 ? Can you please put light on this ?
if not , do I need to upgrade to ISE 1.3 ? what is the process to upgrade to ISE 1.3 ?
Thanks in advance

ISE can provision clients with agent and configure agent profiles.You have Client-provisioning policies that enable users to download and install resources on client devices.(Windows and Mac OS X NAC Agents, Cisco NAC Web Agent.

HT4623 How can i solve installation problem with iOS 6.

How can i solve installation problem with iOS 6. I've tried to install it on my iPhone 4 but nothing turned out. Thanks in advance!!!!

can you connect your device to Tiunes and check to see if there are any files in
OSX: ~/Library/Logs/Crashreporter/Mobiledevice/<Devicename>/
Windows: %appdata%\Apple Computer\Logs\Crashreporter\MobileDevice\<Devicename>
specifically named OTA......
Also for the failed itunes restore please attach the contents of the latest log in
OSX: ~/Library/Logs/<iphone or ipod or ipad> updater logs
Windows: C:/User/ Appdata/Roaming/iTunes/<iphone or ipod or ipad> updater logs

Unable to use proxy server with MAC OS X Anyconnect client

Hi All,
I have a VPN setup thru a Cisco 5520, Windows clients connect just find and the end users configure there browser to use our internal proxy servers. Users with the MAC OS X Anyconnect client can connect, they configure their Mac to use our proxy server, but the broswers will not work, clients can reach networks and resources behind the VPN gateway and have access to the Proxy(Tried a telnet to that hostname/port). Anyone run into this issue before? I am running ASA 8.3(2), Anyconnect(OS X) 3.1.01065.
Thank You

We had the same problem.
We are behind government firewall so I don't know which Cisco firewall is used but we are using AnyConnect to establish VPN from internet to LAN behind firewall. We have no problems with Windows. With Mac OS X connection through proxy didn't work with Safari and Chrome (both are using system Proxy setting), but it did work with Firefox (which has it's own Proxy).
Finally we found out that ethernet MTU size was the culprit. When we set it to manual, with size being 1347 (or less), proxy started to work.

SSL Certificate Mismatch with AnyConnect client

Hello,
We are having a problem with the AnyConnect client when connecting to our VPN. We are running the following:
AnyConnect v2.4.0202
(2 each) ASA v8.2(1) -- active/standby failover
AnyConnect Essentials Licensing
NOTE: We are not using certificates for authentication.
Primary clients: Windows XP and Windows 7
Problem
We have purchased an Entrust certificate for our ASA failover cluster called "vpn.company.com" and the it is attached to the outside interface on the ASA.
Steps to Reproduce
Install the AnyConnect (AC) client via https://vpn.company.com/. Connection occurs here without issue.
Once the AC client is installed and we try to use it in stand-alone mode (i.e., w/o hitting the ASA w/ a browser), a certificate mismatch occurs, and AC brings up the Windows/IE Security Alert dialog (see attachment CertError.jpg).
The user must press Yes to bypass mismatch.
PROBLEM: On Windows 7, the user must have administrative privileges and run the AC client as administrator -- otherwise, they get a dialog saying "Unable to establich VPN" (see attachment Unable.jpg).
The issue is we have a valid certificate that should be used for the connection. However, when looking at the connections made by the AC client with Fiddler, it would appear that the AC client is trying to connect directly to the ASA's IP address, and not the name. This is a nuisance for XP users, and a show-stopper for Win7 users as they do not have admin privileges.
I have not been able to find any documentation on Cisco.com relating to this issue. In short, how do I get the AC client to use "vpn.company.com" so there is no Cert mismatch?
Thanks,
-Matt

Tim,
I will read through the article more thoroughly; I've already been through parts of it -- won't hurt to go through again. I did initially have the IP address in my XML file, and immediately removed it when I noticed that it was using the IP address in the FIddler dump. It hasn't had any effect unfortunately -- even with uninstalling and re-installing the AC client locally.
The only other article/post I've come across on Cisco's site that comes close is here:
Cisco Support Community: ASA VPN Load Balancing/Clustering with Digital Certificates Deployment Guide
which seems to suggest that I will need a UCC certificate (which seems ridiculous) to do some of what I need to do. However the issue with that post is that it still wouldn't fix the issue where the AC client is using the IP address.
I will let you know if I find any smoking guns in the doco link you sent. Any other thoughts appreciated. I can't believe Cisco made the setup of the AC client this convoluted.
Thanks!
-Matt

Cisco AnyConnect Secure Mobility Client with IPsec

Hello,
Current equipment
ASA 5520
ASA Version 8.4(6)
ASDM Version 7.1(3)
IPsec(IKEv1)
Cisco VPN Client
Cisco AnyConnect Secure Mobility Client
Version 3.1.04072
I need to configure the vpn client with ipsec using the version of the vpn client what i'm talk.
The first time I complete all the parameters. I note what file was edit. The file what was edit is this file "preferences.xml"
c:\users\user\AppData\Local\Cisco\Cisco AnyConnect Secure Mobility Client
If I edit this file "preference.xml" all setting change but not help me in made a solution.
The file contains this
<?xml version="1.0" encoding="UTF-8"?>
<AnyConnectPreferences>
<DefaultUser>user</DefaultUser>
<DefaultSecondUser></DefaultSecondUser>
<ClientCertificateThumbprint></ClientCertificateThumbprint>
<ServerCertificateThumbprint></ServerCertificateThumbprint>
<DefaultHostName>server</DefaultHostName>
<DefaultHostAddress></DefaultHostAddress>
<ProxyHost></ProxyHost>
<ProxyPort></ProxyPort>
<SDITokenType>none</SDITokenType>
<ControllablePreferences>
<LocalLanAccess>false</LocalLanAccess>
<AutoConnectOnStart>false</AutoConnectOnStart>
<BlockUntrustedServers>false</BlockUntrustedServers></ControllablePreferences>
</AnyConnectPreferences>
What i need to know is the "sentence" or line of configuration what i have to introduce in this file to reference the different ipsec profile. If I am told that I must update the handle or asdm version. I can do it.
Somebody can help me please

Here is a link to an example of configuring AnyConnect to use IKEv2. According to this ASA 8.4 and AnyConnect 3.1 should be ok.
http://www.cisco.com/c/en/us/support/docs/security/anyconnect-secure-mobility-client/113692-ac-ikev2-ca-00.html
HTH
Rick

Associate anyconnect client software with specific profile?

Hi folks,
I want to beta test a new release of the Windows AnyConnect client software with a small number of users. We use the web deployment feature. Is there a way for us to associate a specific version of the client software with a profile? This seems like the easiest way to release the new software to a small group of people.
Thanks
Pat

The only "AutoUpdate" Value in my profile for 3.x is: true
I think if you put the new AC image in flash it's and point to it in the configuration, it's going to update all the clients - not just a specified tunnel or group. I am not 100% on this though.
Is manually installing it in your test environment an option? This is what what we did then exported profile from the firewall and placed it in the directory for the test client.

AnyConnect VPN with Built-in Client Firewall on Windows 7

Hi
I've searched the forums and documentation and can't seem to find a definitive answer to my scenario.
We have an ASA5510 with SecPlus running 8.3.2
We currently use VPN client on XP to invoke the built-in firewall to prevent incoming connections to the PC when the tunnel is established – the Cisco built-in client is not supported on Win7.
We’re looking to provide similar functionality with the AnyConnect client, i.e.
Full network access over the AnyConnect client (connection can be established manually)
AnyConnect client enforcing a local policy on the PC preventing incoming connections when the tunnel is established
No clientless requirements
No mobile requirements (apple, android etc)
No secure desktop requirements
I’d like to ascertain if:-
Does the AnyConnect client include a firewall that is supported on Windows 7 (32 and 64 bit)?
Will the Essential licence give me the functionality I require, or do I need a Premium?
Thanks

Hi Prashanth,
I think you can only use per-app VPN with SSL VPN.
Hope this helps,
Julien

Anyconnect Client with IOS Webvpn - Multiple Installs

Similar Messages

Maybe you are looking for