Ap 1200 cannot find bootable file
My AP 1200 cannot find the bootable file. It only gives me "ap:". Very little option to work with.
When I do "dir flash:", I only have env_vars, private-config and private-multiple-fs three files in my flash. Does anybody know how to rebuild config or load the boot file? I did "version" and it gives me version: 12.3(2)JA4.
thanks,
Gene
Hi Gene,
Have a look at the method outlined below:
Using the MODE button
You can use the MODE button on 1100 and 1200 series access points to reload the access point image file from an active Trivial File Transfer Protocol (TFTP) server on your network or on a PC connected to the access point Ethernet port.
Note If your access point experiences a firmware failure or a corrupt firmware image, indicated by three red LED indicators, you must reload the image from a connected TFTP server.
Note This process resets all configuration settings to factory defaults, including passwords, WEP keys, the access point IP address, and SSIDs.
Follow these steps to reload the access point image file:
Step 1 The PC you intend to use must be configured with a static IP address in the range of 10.0.0.2 to 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1100-k9w7-tar.122-15.JA.tar for an 1100 series access point or c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1100-k9w7-tar.default for an 1100 series access point or c1200-k9w7-tar.default for a 1200 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power (the power jack for external power or the Ethernet cable for in-line power) from the access point.
Step 6 Press and hold the MODE button while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds), and release the MODE button.
Step 8 Wait until the access point reboots as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, you must reconfigure the access point by using the Web-browser interface or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_guide_chapter09186a0080209250.html#wp1040300
Hope this helps!
Rob
Please remember to rate helpful posts.....
Similar Messages
-
MDT2012 - Deployment failed, the system cannot find the file specified
Hi everybody.
First, excuse me for my english, i think it's not the best thing I'm able to do, but now, I REALLY need help.
I encounter issues with my MDT 2012 Update 1 platform.
I have 5 systems to capture. All systems have 3 partitions (System, softwares, data). Capture is working fine for all parts.
In my Task Sequence, to deploy these images (C, D and E parts), I use a script after the "Install Operating System" which runs imagex to deploy the WIM images for D: and E:.
The script is the following :
"%DeployRoot%\Tools\x64\imagex" /apply "%DeployRoot%\Operating Systems\D_Drive\D_Drive.wim" 1 %DDrive%"
But, for some images, the task fails on the "D" drive deployement. The wizard shows the following error :
Litetouch deployment dailed, return code = -214767259 0x80004005
Failed to run the action: InstallD (ie : the script above)
The system cannot find the file specified. (Error: 00000002; Source: Windows)
The error is on my task which uses imagex to deploy my D and E WIM.
So I looked to see if the file's path was the good one.
And it is !!!
Wizard says that the file couldn't be find, but the file is existing, and in the good path.
For your information, there is no problem when I don't use multicast. Everything is working fine on unicast, not on multicast.
I even encounter this issue if I use my MDT server and my computers on the same switch.
Any help would be gratefull, my client gives me the week to resolve the issue.
ThanksBDD.LOG
<![LOG[Microsoft Deployment Toolkit version: 6.1.2373.0]LOG]!><time="16:53:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[The task sequencer log is located at X:\WINDOWS\TEMP\SMSTSLog\SMSTS.LOG. For task sequence failures, please consult this log.]LOG]!><time="16:53:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Write all logging text to \\192.168.36.208\Logs$]LOG]!><time="16:53:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Validating connection to \\192.168.36.208\Logs$]LOG]!><time="16:53:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Already connected to server 192.168.36.208 as that is where this script is running from.]LOG]!><time="16:53:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Will boot into Windows PE architecture x64 to match OS being deployed.]LOG]!><time="16:53:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[OSDTargetDriveCache was determined earlier : V:]LOG]!><time="16:53:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Property OSDTargetDriveCache is now = V:]LOG]!><time="16:53:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Property OSDisk is now = V:]LOG]!><time="16:53:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Open Control File: OperatingSystems]LOG]!><time="16:53:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[------ Applying Windows image using ImageX.exe ------]LOG]!><time="16:53:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[LTI applying image \\192.168.36.208\MDT$\Operating Systems\Master 3 avec Sysprep\CAPT.wim using ImageX]LOG]!><time="16:53:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Event 41023 sent: LTI applying image \\192.168.36.208\MDT$\Operating Systems\Master 3 avec Sysprep\CAPT.wim using ImageX]LOG]!><time="16:53:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Property SourcePath is now = \\192.168.36.208\MDT$\Operating Systems\Master 3 avec Sysprep]LOG]!><time="16:53:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Multicast transfer to directory: C:\MININT\Operating Systems\Master 3 avec Sysprep]LOG]!><time="16:53:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[<Message containing password has been suppressed>]LOG]!><time="16:53:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Command has been started (process ID 1348)]LOG]!><time="16:53:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ZTI Heartbeat: command has been running for 0 minutes (process ID 1348)]LOG]!><time="16:53:57.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Event 41003 sent: ZTI Heartbeat: command has been running for 0 minutes (process ID 1348)]LOG]!><time="16:53:57.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console >
]LOG]!><time="16:53:57.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > Transfer Started.
]LOG]!><time="16:53:57.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ZTI Heartbeat: command has been running for 5 minutes (process ID 1348)]LOG]!><time="16:58:01.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Event 41003 sent: ZTI Heartbeat: command has been running for 5 minutes (process ID 1348)]LOG]!><time="16:58:01.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console >
]LOG]!><time="17:00:43.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > Transfer Complete [0x0].]LOG]!><time="17:00:43.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Return code from command = 0]LOG]!><time="17:00:43.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Multicast transfer of "\\192.168.36.208\MDT$\Operating Systems\Master 3 avec Sysprep\CAPT.wim" to "C:\MININT\Operating Systems\Master 3 avec Sysprep\CAPT.wim" completed successfully.]LOG]!><time="17:00:43.000+000" date="02-19-2014" component="LTIApply"
context="" type="1" thread="" file="LTIApply">
<![LOG[Cleaning off old operating system]LOG]!><time="17:00:43.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Skipping V:\Drivers]LOG]!><time="17:00:43.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[New ZTIDiskPartition : \\MININT-1H9O4H6\root\cimv2:Win32_LogicalDisk.DeviceID="V:" \\MININT-1H9O4H6\root\cimv2:Win32_DiskPartition.DeviceID="Disk #0, Partition #0"]LOG]!><time="17:00:43.000+000" date="02-19-2014" component="LTIApply"
context="" type="1" thread="" file="LTIApply">
<![LOG[Enabling 8dot3 name support on volume V:]LOG]!><time="17:00:43.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[About to run command: "\\192.168.36.208\MDT$\Tools\X64\imagex.exe" /apply "C:\MININT\Operating Systems\Master 3 avec Sysprep\CAPT.wim" 1 V:]LOG]!><time="17:00:43.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread=""
file="LTIApply">
<![LOG[Command has been started (process ID 536)]LOG]!><time="17:00:43.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > ImageX Tool for Windows]LOG]!><time="17:00:43.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > Copyright (C) Microsoft Corp. All rights reserved.]LOG]!><time="17:00:43.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > Version: 6.1.7600.16385]LOG]!><time="17:00:43.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > [ 0% ] Applying progress ]LOG]!><time="17:00:43.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > [ 0% ] Applying progress ]LOG]!><time="17:00:49.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > [ 1% ] Applying progress ]LOG]!><time="17:00:49.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > [ 2% ] Applying progress ]LOG]!><time="17:00:55.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > [ 3% ] Applying progress ]LOG]!><time="17:00:58.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > [ 4% ] Applying progress: 5:28 mins remaining ]LOG]!><time="17:01:03.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > [ 5% ] Applying progress: 5:33 mins remaining ]LOG]!><time="17:01:07.000+000"
<![LOG[ Console > [ 99% ] Applying progress: 3 secs remaining ]LOG]!><time="17:06:43.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > [ 100% ] Applying progress ]LOG]!><time="17:06:50.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > Successfully applied image.]LOG]!><time="17:06:51.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > Total elapsed time: 6 min 7 sec]LOG]!><time="17:06:51.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Return code from command = 0]LOG]!><time="17:06:51.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Property LTIDirtyOS is now = TRUE]LOG]!><time="17:06:51.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[The image C:\MININT\Operating Systems\Master 3 avec Sysprep\CAPT.wim was applied successfully.]LOG]!><time="17:06:51.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Event 5625 sent: The image C:\MININT\Operating Systems\Master 3 avec Sysprep\CAPT.wim was applied successfully.]LOG]!><time="17:06:51.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[About to run command: "\\192.168.36.208\MDT$\Tools\X64\bootsect.exe" /nt60 V:]LOG]!><time="17:06:52.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Command has been started (process ID 1252)]LOG]!><time="17:06:52.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > Target volumes will be updated with BOOTMGR compatible bootcode.
]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console >
]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > V: (\\?\Volume{2ab15dec-99c9-19e3-baf6-94de80bab573})
]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console >
]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > Successfully updated NTFS filesystem bootcode.
]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console >
]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > Bootcode was successfully updated on all targeted volumes.
]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Return code from command = 0]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Find the boot drive (if any) [True] [6.1.7601.18229] [False]]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[New ZTIDiskPartition : \\MININT-1H9O4H6\root\cimv2:Win32_DiskPartition.DeviceID="Disk #0, Partition #0" \\MININT-1H9O4H6\root\cimv2:Win32_LogicalDisk.DeviceID="V:"]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="LTIApply"
context="" type="1" thread="" file="LTIApply">
<![LOG[New ZTIDisk : \\MININT-1H9O4H6\root\cimv2:Win32_DiskDrive.DeviceID="\\\\.\\PHYSICALDRIVE0"]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Found bootable drive (No Boot File Test) [ V: ]: \\MININT-1H9O4H6\root\cimv2:Win32_LogicalDisk.DeviceID="V:"]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Ready to Prepare boot partition: V:]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[About to run command: cscript.exe //nologo "\\192.168.36.208\MDT$\Scripts\ztiRunCommandHidden.wsf" ""\\192.168.36.208\MDT$\Tools\X64\BCDBoot.exe" V:\windows /l fr-fr /s V:"]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="LTIApply"
context="" type="1" thread="" file="LTIApply">
<![LOG[Microsoft Deployment Toolkit version: 6.1.2373.0]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="ztiRunCommandHidden" context="" type="1" thread="" file="ztiRunCommandHidden">
<![LOG[The task sequencer log is located at X:\WINDOWS\TEMP\SMSTSLog\SMSTS.LOG. For task sequence failures, please consult this log.]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="ztiRunCommandHidden" context="" type="1" thread=""
file="ztiRunCommandHidden">
<![LOG[Write all logging text to \\192.168.36.208\Logs$]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="ztiRunCommandHidden" context="" type="1" thread="" file="ztiRunCommandHidden">
<![LOG[Validating connection to \\192.168.36.208\Logs$]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="ztiRunCommandHidden" context="" type="1" thread="" file="ztiRunCommandHidden">
<![LOG[Already connected to server 192.168.36.208 as that is where this script is running from.]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="ztiRunCommandHidden" context="" type="1" thread="" file="ztiRunCommandHidden">
<![LOG[About to run command: \\192.168.36.208\MDT$\Tools\X64\BCDBoot.exe V:\windows /l fr-fr /s V:]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="ztiRunCommandHidden" context="" type="1" thread="" file="ztiRunCommandHidden">
<![LOG[Command has been started (process ID 1984)]LOG]!><time="17:06:54.000+000" date="02-19-2014" component="ztiRunCommandHidden" context="" type="1" thread="" file="ztiRunCommandHidden">
<![LOG[ Console > Boot files successfully created.]LOG]!><time="17:06:55.000+000" date="02-19-2014" component="ztiRunCommandHidden" context="" type="1" thread="" file="ztiRunCommandHidden">
<![LOG[Return code from command = 0]LOG]!><time="17:06:55.000+000" date="02-19-2014" component="ztiRunCommandHidden" context="" type="1" thread="" file="ztiRunCommandHidden">
<![LOG[Command has returned: 0]LOG]!><time="17:06:55.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Run Command: X:\WINDOWS\SYSTEM32\bcdedit.exe /Store "V:\boot\bcd" /timeout 0]LOG]!><time="17:06:55.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[BCD> The operation completed successfully.]LOG]!><time="17:06:55.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[BCDEdit returned ErrorLevel = 0]LOG]!><time="17:06:55.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Created scratch folder.]LOG]!><time="17:06:55.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Copy File: C:\MININT\unattend.xml to V:\Windows\Panther\Unattend.xml]LOG]!><time="17:06:55.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Copied unattend.xml to V:\Windows\Panther for image apply.]LOG]!><time="17:06:55.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[About to run command: dism.exe /Image:V:\ /Apply-Unattend:V:\Windows\Panther\Unattend.xml /ScratchDir:C:\MININT\Scratch]LOG]!><time="17:06:55.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Command has been started (process ID 1516)]LOG]!><time="17:06:55.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > Deployment Image Servicing and Management tool]LOG]!><time="17:06:55.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > Version: 6.1.7600.16385]LOG]!><time="17:06:55.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > Image Version: 6.1.7600.16385]LOG]!><time="17:06:56.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[ Console > The operation completed successfully.]LOG]!><time="17:06:57.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Return code from command = 0]LOG]!><time="17:06:57.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[LTIApply processing completed successfully.]LOG]!><time="17:06:57.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Event 41001 sent: LTIApply processing completed successfully.]LOG]!><time="17:06:57.000+000" date="02-19-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Command completed, return code = -2147467259]LOG]!><time="17:10:54.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Litetouch deployment failed, Return Code = -2147467259 0x80004005]LOG]!><time="17:10:54.000+000" date="02-19-2014" component="LiteTouch" context="" type="3" thread="" file="LiteTouch">
<![LOG[Event 41014 sent: Litetouch deployment failed, Return Code = -2147467259 0x80004005]LOG]!><time="17:10:54.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[For more information, consult the task sequencer log ...\SMSTS.LOG.]LOG]!><time="17:10:54.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Property RetVal is now = -2147467259]LOG]!><time="17:10:54.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Validating connection to \\192.168.36.208\Logs$]LOG]!><time="17:10:54.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Already connected to server 192.168.36.208]LOG]!><time="17:10:54.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[OSDTargetDriveCache was determined earlier : V:]LOG]!><time="17:10:54.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Property OSDTargetDriveCache is now = V:]LOG]!><time="17:10:54.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Property OSDisk is now = V:]LOG]!><time="17:10:54.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying C:\MININT\SMSOSD\OSDLOGS\LiteTouch.log to \\192.168.36.208\Logs$\MININT-1H9O4H6\LiteTouch.log]LOG]!><time="17:10:54.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying C:\MININT\SMSOSD\OSDLOGS\LTIApply.log to \\192.168.36.208\Logs$\MININT-1H9O4H6\LTIApply.log]LOG]!><time="17:10:54.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying C:\MININT\SMSOSD\OSDLOGS\LTICopyScripts.log to \\192.168.36.208\Logs$\MININT-1H9O4H6\LTICopyScripts.log]LOG]!><time="17:10:54.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying C:\MININT\SMSOSD\OSDLOGS\PnpEnum.xml to \\192.168.36.208\Logs$\MININT-1H9O4H6\PnpEnum.xml]LOG]!><time="17:10:54.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying C:\MININT\SMSOSD\OSDLOGS\Wizard.log to \\192.168.36.208\Logs$\MININT-1H9O4H6\Wizard.log]LOG]!><time="17:10:54.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying C:\MININT\SMSOSD\OSDLOGS\ZTIBDE.log to \\192.168.36.208\Logs$\MININT-1H9O4H6\ZTIBDE.log]LOG]!><time="17:10:54.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying C:\MININT\SMSOSD\OSDLOGS\ZTIConfigure.log to \\192.168.36.208\Logs$\MININT-1H9O4H6\ZTIConfigure.log]LOG]!><time="17:10:55.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying C:\MININT\SMSOSD\OSDLOGS\ZTIDiskpart.log to \\192.168.36.208\Logs$\MININT-1H9O4H6\ZTIDiskpart.log]LOG]!><time="17:10:55.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying C:\MININT\SMSOSD\OSDLOGS\ZTIDrivers.log to \\192.168.36.208\Logs$\MININT-1H9O4H6\ZTIDrivers.log]LOG]!><time="17:10:55.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying C:\MININT\SMSOSD\OSDLOGS\ZTIGather.log to \\192.168.36.208\Logs$\MININT-1H9O4H6\ZTIGather.log]LOG]!><time="17:10:55.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying C:\MININT\SMSOSD\OSDLOGS\ZTINextPhase.log to \\192.168.36.208\Logs$\MININT-1H9O4H6\ZTINextPhase.log]LOG]!><time="17:10:55.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying C:\MININT\SMSOSD\OSDLOGS\ZTIPatches.log to \\192.168.36.208\Logs$\MININT-1H9O4H6\ZTIPatches.log]LOG]!><time="17:10:55.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying C:\MININT\SMSOSD\OSDLOGS\ztiRunCommandHidden.log to \\192.168.36.208\Logs$\MININT-1H9O4H6\ztiRunCommandHidden.log]LOG]!><time="17:10:55.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying C:\MININT\SMSOSD\OSDLOGS\ZTIValidate.log to \\192.168.36.208\Logs$\MININT-1H9O4H6\ZTIValidate.log]LOG]!><time="17:10:55.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying X:\WINDOWS\TEMP\SMSTSLog\SMSTS.LOG to \\192.168.36.208\Logs$\MININT-1H9O4H6\SMSTS.LOG]LOG]!><time="17:10:55.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying X:\WINDOWS\Debug\Netsetup.log to \\192.168.36.208\Logs$\MININT-1H9O4H6\]LOG]!><time="17:10:55.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying X:\WINDOWS\System32\wpeinit.log to \\192.168.36.208\Logs$\MININT-1H9O4H6\]LOG]!><time="17:10:55.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Copying log C:\MININT\SMSOSD\OSDLOGS\BDD.log contents to \\192.168.36.208\Logs$\MININT-1H9O4H6\BDD.LOG]LOG]!><time="17:10:55.000+000" date="02-19-2014" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> -
I put in my memory card to the left side of the computer, but I cannot find the file of pictures anywhere. Its not even on my desktop. What should I do and how can I get it to show up on my desktop?
If your Mac is new-ish and has one of the Lions as its OS, the drives, cards, USB sticks no longer show up, even though they're there. Go to Finder's Preferences and tick the corresponding items in the General and Sidebar tabs.
-
Error message on my development workstation: The system cannot find the file specified.
Post Author: cseverin
CA Forum: Crystal Reports
Hi,
I am currently developing an ASP.NET website using Visual Studio.NET 2005. I am using the .NET 2.0 framework, VB.NET as my programming language and I connect successfully to a SQL Server 2005 database. I can select, insert, update and delete data from the database elsewhere in my project, so I know basic connectivity isn't an issue. The problem seems to be with Crystal Reports.
I created a folder called 'Reports' in my project and added a Crystal Report file (OpenFiles.rpt) to it. I designed the report and initally used a hard-coded SQL query as its datasource so I could quickly get the database fields onto the report and preview them. All worked fine.
To make the report accessible to the rest of the website, I created an .xsd dataset file containing the three tables (and their corresponding tableadapters) that the report requires and then redeveloped the report using the dataset as the datasource for the report. After doing this, the preview no longer worked.
Next, I added a page to the website and dragged a Crystal Report Viewer Control onto it. In the code behind the page I wrote:
Option Strict On
Imports System.Data
Imports CrystalDecisions.CrystalReports.Engine
Imports CrystalDecisions.Shared
Partial Class Reports
Inherits System.Web.UI.Page
Private objOpenFilesreport As OpenFilesReport
Private rptOpenFiles As ReportDocument
Private strLastErrorMessage As String = Nothing
Private errLastException As Exception = Nothing
Dim strFileKey As String
Dim strJurisdictionCode As String
Dim strStaffId As String
Dim strReportId As String
Private Sub ConfigureCrystalReports()
Dim reportPath As String = Server.MapPath("OpenFiles.rpt")
Dim rptopenfiles As New ReportDocument
rptOpenFiles.Load(reportPath) <== I checked this during execution and the value correctly points to the OpenFiles.rpt file in the Reports folder of my project
Dim ConnectionInfo As ConnectionInfo = New ConnectionInfo()
ConnectionInfo.DatabaseName = my database
ConnectionInfo.UserID = login id of user
ConnectionInfo.Password = user's password
SetDBLogonForReport(ConnectionInfo, rptopenfiles)
CrystalReportViewer1.ReportSource = rptopenfiles
End Sub
Protected Sub Page_Init(ByVal sender As Object, ByVal e As System.EventArgs) Handles Me.Init
ConfigureCrystalReports()
End Sub
Private Sub SetDBLogonForReport(ByVal ConnectionInfo As ConnectionInfo, ByVal myReportDocument As ReportDocument)
Dim myTables As Tables = myReportDocument.Database.Tables
For Each myTable As CrystalDecisions.CrystalReports.Engine.Table In myTables
Dim myTableLogonInfo As TableLogOnInfo = myTable.LogOnInfo
myTableLogonInfo.ConnectionInfo = ConnectionInfo
myTable.ApplyLogOnInfo(myTableLogonInfo)
Next
End Sub
End Class
I added a hyperlink to one of the existing pages on the website to navigate to this page with the report viewer on it. When I run the website in Visual Studio and click on the hyperlink I get the following:
Server Error in '/MyTest' Application.
The system cannot find the file specified.
Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.Runtime.InteropServices.COMException: The system cannot find the file specified.Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below. Stack Trace:
[COMException (0x80004005): The system cannot find the file specified.
]
CrystalDecisions.ReportAppServer.ClientDoc.ReportClientDocumentClass.Open(Object& DocumentPath, Int32 Options) +0
CrystalDecisions.ReportAppServer.ReportClientDocumentWrapper.Open(Object& DocumentPath, Int32 Options) +126
CrystalDecisions.ReportAppServer.ReportClientDocumentWrapper.EnsureDocumentIsOpened() +442
[Exception: Load report failed.]
CrystalDecisions.ReportAppServer.ReportClientDocumentWrapper.EnsureDocumentIsOpened() +513
CrystalDecisions.CrystalReports.Engine.ReportDocument.Load(String filename, OpenReportMethod openMethod, Int16 parentJob) +1378
CrystalDecisions.CrystalReports.Engine.ReportDocument.EnsureLoadReport() +149
CrystalDecisions.CrystalReports.Engine.ReportDocument.get_DataDefinition() +85
CrystalDecisions.CrystalReports.Engine.ReportDocument.get_ParameterFields() +158
CrystalDecisions.Web.CrystalReportSource.BindControlParameter(Parameter parameter) +130
CrystalDecisions.Web.CrystalReportSource.DataBindParameters() +191
CrystalDecisions.Web.CrystalReportSource.EnsureParameters(Boolean forceDataBind) +90
CrystalDecisions.Web.CrystalReportSource.LoadCompleteEventHandler(Object sender, EventArgs e) +47
System.Web.UI.Page.OnLoadComplete(EventArgs e) +96
System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) +4086
Version Information: Microsoft .NET Framework Version:2.0.50727.832; ASP.NET Version:2.0.50727.832
Any ideas, anyone?
Also, assuming I can get past this error, I will need to figure out how to fill the tables in the .xsd dataset file. I have written a class for the dataset that includes functions that populate the tables in the dataset from the database by executing SQL queries. But how do I call these functions at the time the report is run?
This is my first Crystal report written in .NET and I've been struggling with it for days now. Any help would be most appreciated!
Thanks very much!
Chris Severinhello, the error message is obviously coming from one of the installed mcafee extensions. please directly contact mcafee technical support - they can likely give you more detailed guidance and are the only ones who can fix bugs or make necessary adjustments in the addon.
-
Hello! I have one iTunes library on my iPod and one iTunes library on my computer. When I connect my iPod touch to my PC, however, I cannot find any files in my iPod except for pictures. How can I find the music files so I can add them to my iTunes?
You can't do that.
And before you decide to store any music that you own on a computer at work, talk to your IT department. Many organizations do not permit it for legal reasons. Standard policies are that anything stored on company owned computers is the property of the company. It could not be legally stored on their machines unless you transfer the licenses and all copies, physical and digital, to the company, meaning you no longer own the music. If they were to be audited and could not prove that they own the music, they would be subject to copyright violation penalties. Just use your iPod when you're at the office if you want to listen to music. -
App-v 4.6: cannot find the file specified
Hi,
Please see my previous
post.
In short: an application needs Internet Explorer activex, then a plugin for Excel. My App-v package is working (Internet Explorer opening), but the Excel plugin does not work. It says "cannot find the file specified".
I copied the excel shortcut from start menu to q:\packagename.
Please advise.
J.
Jan Hoedt
In .osd file of Excel plugin, there is the following:
<CODEBASE HREF="RTSP://%SFT_SOFTGRIDSERVER%:554/WindowsX64/Application/1.0/excelplugin.sft" GUID="9FA88591-089E-4E57-89D5-C23239E83238" PARAMETERS="" FILENAME="%CSIDL_PROGRAM_FILES%\Microsoft Office\Office12\EXCEL.EXE"
SYSGUARDFILE="applic.001\osguard.cp" SIZE="305879730"/>
<WORKINGDIR>%CSIDL_PROGRAM_FILES%\Microsoft Office\Office12</WORKINGDIR>
The CSIDL_PROGRAM_FILES%, is that correct? If not, can I change it and how? Should I then reimport the package?
I might have found a solution but please advise:
http://blog.gridmetric.com/2011/09/26/possible-caveats-in-mixing-32-bit-and-64-bit-app-v-packages-and-environments/
Office is x86, so I probably should change the %CSIDL_Programfiles% to %programfiles(x86)%?Changing CSIDL_PROGRAM_FILES to %programfiles(x86)% is worth a try.
A common reason for that 'cannot find the file..' error message also often can be resolved by removing the Workingdir entry (<WORKINGDIR></WORKINGDIR> or just <WORKINGDIR/>.
The way to apply the change depends on your deployment scenario. With an App-V Management Server (and for a test packae) you could modify (a copy of) the original .OSD file in the content share. Make sure you save with 'save as' and then 'Unicode'. Then
re-initiate a Server Refresh from the client, that should download the new OSD.
You also could - if it is permitted - create a copy of the client-local copy of the OSD file (you can figure that out with the Client Management Console). Double-Clicking that modified copy could do the trick.
If you use another deployment method (SCCM, MSI) you would need to moify the OSD file using the App-V Sequencer.
Whatever method you use during troubleshooting: For the 'final' pacage you should open the original package on the Sequencer ('Edit'), make the changes there and re-save + re-deploy the package. This makes sure that all information is consitent across the
various App-V files
Falko
Twitter
@kirk_tn | Blog
kirxblog | Web
kirx.org | Fireside
appvbook.com -
got a new wireless connection for my mac and cannot figure out how to delete the last connection service I had. Everytime I shut the computer, the network goes back to the other one. I cannot find the file ANYWHERE
Under Network Preferences, select the WiFi
click on "Advanced..." button
Select the network you want to delete from the list and click on "-"
Click "Ok"
Click "Apply"
Well done ;-)
You may also want to delete the wireless key from Keychain.
Open Keychain, seach for the old wifi network name, slect it and click delete -
I started getting this error message for the first time today. When I look in the event log I see it every time anyone tries to sync to a mobile device to the exchange server. I've also had this problem trying to connect using
Outlook. I believe it is an IIS issue but I'm not absolutely sure so I'm posting this in the Exchange forum as well.
The event viewer has the following information...
3008
A configuration error has occurred.
5/1/2014 10:41:08 PM
5/2/2014 5:41:08 AM
7539d8a38c8b47869eda3f1749aba08d
1
1
0
/LM/W3SVC/1/ROOT/Microsoft-Server-ActiveSync-75-130434828686436855
Full
/Microsoft-Server-ActiveSync
C:\Program Files\Microsoft\Exchange Server\V14\ClientAccess\sync\
SERVER
16284
w3wp.exe
NT AUTHORITY\SYSTEM
ConfigurationErrorsException
Could not load file or assembly 'System.ServiceModel.Activation, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35' or one of its dependencies. The system cannot find the file specified.
https://remote.testserver.com:443/Microsoft-Server-ActiveSync/default.eas?User=user.name&DeviceId=ApplC39GQ5xxxxxx&DeviceType=iPhone&Cmd=Ping
/Microsoft-Server-ActiveSync/default.eas
174.224.130.31
False
NT AUTHORITY\SYSTEM
24
NT AUTHORITY\SYSTEM
False
at System.Web.Configuration.ConfigUtil.GetType(String typeName, String propertyName, ConfigurationElement configElement, XmlNode node, Boolean checkAptcaBit, Boolean ignoreCase) at System.Web.Configuration.Common.ModulesEntry..ctor(String name, String typeName, String propertyName, ConfigurationElement configElement) at System.Web.HttpApplication.BuildIntegratedModuleCollection(List`1 moduleList) at System.Web.HttpApplication.GetModuleCollection(IntPtr appContext) at System.Web.HttpApplication.RegisterEventSubscriptionsWithIIS(IntPtr appContext, HttpContext context, MethodInfo[] handlers) at System.Web.HttpApplication.InitSpecial(HttpApplicationState state, MethodInfo[] handlers, IntPtr appContext, HttpContext context) at System.Web.HttpApplicationFactory.GetSpecialApplicationInstance(IntPtr appContext, HttpContext context) at System.Web.Hosting.PipelineRuntime.InitializeApplication(IntPtr appContext)
I have tried most, if not all, of the different post's suggestions to no avail.
The steps I have taken are as follows...
1. Repaired .Net 4 (Both the client and extended)
2. Uninstalled and reinstalled .Net Framework 4.0.
3. Verified that the dll exists.
4. Checked the applicationHost.config file. It contains the follow statement...
<add name="ServiceModel-4.0" type="System.ServiceModel.Activation.ServiceHttpModule, System.ServiceModel.Activation, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" preCondition="managedHandler,runtimeVersionv2.0"
/>
5. Changed the following line in web.config to include the runtimeVersion...
<add name="ServiceModel" type="System.ServiceModel.Activation.HttpModule, System.ServiceModel.Activation, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" preCondition="managedHandler,runtimeVersionv2.0" />
6. Executed aspnet_regiis.exe -iru from the ...\Framework64\v4.0.30319 directory.
7. Went to inetpub\history to use an applicationHost.config file from yesterday but it only has history from 9PM tonight. It probably had what I needed before I started changing it tonight.
I still receive the same error message.
Like I said everything was working yesterday. In fact I didn't hear or see any issue until after 1PM today.
Any help would be very appreciated!Hi,
Please confirm whether users can access their mailboxes from Outlook Web Access or not. We can do the following changes to have a try:
1. In IIS > Application Pools, change the .NET Framework Version to v2.0 and restart IIS service.
2. If it doesn’t work, explore the Default Web site.
3. Renamed the web.config file to web.config.old
4. Reset IIS using iisreset command to have a try.
Thanks,
Winnie Liang
TechNet Community Support -
Hello,
I am creating an app using NAPA tool in Office 365. I am trying to "Add an attachment" to a custom list item using SPServices. When I am using my code (jquery code) in content editor web part on a page, its working fine, but when I am adding
the same code in an app, its giving me error : "The system cannot find the file specified. (Exception from HRESULT:
0x80070002)" - 500 Internal Server error.
(function () {
// This code runs when the DOM is ready and creates a context object which is
// needed to use the SharePoint object model
$(document).ready(function () {
//alert('In doc ready');
$('.attachmentButton').change(function(event){
var listName = 'UploadTest',
itemId = 2;
handleFileChange(listName,itemId,event.target.files);
function handleFileChange(listName,itemId,files){
alert('In handleFileChange :=' + listName + "" + itemId + "" + files[0]);
alert('files.length :=' + files.length);
var filereader = {},
file = {},
i=0;
//loop over each file selected
for(i = 0; i < files.length; i++) {
alert('In for loop');
file = files[i];
filereader = new FileReader();
filereader.filename = file.name;
alert('filereader.filename :=' + filereader.filename);
filereader.onload = function() {
var data = this.result;
var n=data.indexOf(";base64,") + 8;
//alert('n :=' + n);
//removing the first part of the dataurl give us the base64 bytes we need to feed to sharepoint
data= data.substring(n);
//alert('data :=' + data);
alert('Above SPServices this.filename :=' + this.filename);
$().SPServices({
operation: "AddAttachment",
listName: listName,
asynch: false,
listItemID:itemId,
fileName: this.filename,
attachment: data,
completefunc: function (xData, Status) {
console.log('attachment upload complete',xData,status);
alert('Status :=' + Status);
if (Status.toLowerCase() == "error"){
alert(xData.responseText);
alert(xData.status);
alert(xData.statusText);
filereader.onabort = function() {
alert("The upload was aborted.");
filereader.onerror = function() {
alert("An error occured while reading the file.");
//fire the onload function giving it the dataurl
filereader.readAsDataURL(file);
alert(xData.responseText); - gives error - " "The system cannot find the file specified. (Exception from HRESULT: 0x80070002)""
alert(xData.status); - gives error - "500"
alert(xData.statusText); - gives error - "Internal server error"
Server Publishing infrastructure and Server publishing features are activated on site collection and site respectively.
Any suggestions, why I am getting this error in NAPA ?Hi,
According to your post, my understanding is that you have an issue about adding attachments to list items in app.
To add attachment to list item in the host web, we should first get the list and the list items from the host web, then add the attachments to the list items.
There are two articles about retrieve the list and list items in the host web, you can refer to them.
http://www.dotnetcurry.com/showarticle.aspx?ID=1028
http://www.c-sharpcorner.com/UploadFile/93cb27/retrieve-sharepoint-app-host-web-list-items-in-sharepoint-ho/
What’s more, we can also use the REST API to achieve the same scenario.
http://www.c-sharpcorner.com/UploadFile/472cc1/add-attachments-to-list-items-in-sharepoint-2013-using-rest/
Thanks & Regards,
Jason
Jason Guo
TechNet Community Support -
I have restored one web application in SharePoint Server 2010 from a different domain and can complete successfully. Changed each users domain also to old to new one by using Move-SPUser. But While accessing the site collection it is showing an error
that "Could not load file or assembly 'A##.SP.Intranet, Version=1.0.0.0, Culture=neutral, PublicKeyToken=03b4f320ebedaffc' or one of its dependencies. The system cannot find the file specified."
What may be the reason? Please help me to solve this issue since I am stuck up on this .
Regards
Mine1981Hi Nico
Martens,
Thank you for your reply. But
how can I find out the custom solutions in the source farm. I didn't got any other details regarding this farm other than WSS_Content, Web application Database, SharePoint_Config database back ups.
Please help me to solve the
issue.
Regards
Mine -
I got maven 221 installed
i got jdk 1.6 and 1.5 installed (have tested both)
I have a strange error. All my co-workers can build but I cant. The only thing I can find is that I dont have installed BEA Weblogic but I dont want to have that installed. It should be able to run anyway.
Could someone tell me what is wrong? If you need pom.xml I got that one as well.
process-classes:
[copy] Copying 4 files to C:\hudson\jobs\albpm_ip-identity-asserter_-_Build\workspace\target\mbean-content
[mkdir] Created dir: C:\hudson\jobs\albpm_ip-identity-asserter_-_Build\workspace\target\mbean-jar
[java] Creating an MJF from the contents of directory C:\hudson\jobs\albpm_ip-identity-asserter_-_Build\workspace\target\mbean-content...
[java] Compiling the files...
[java] Creating the list.
[java] Doing the compile.
[java] WLMaker-SubProcess: : Exception in thread "main" java.lang.Error: java.util.zip.ZipException: The system cannot find the file specified
[java] WLMaker-SubProcess: : at weblogic.management.commo.BeanGenDriver.getManagementTempDir(BeanGenDriver.java:93)
[java] WLMaker-SubProcess: : at weblogic.management.commo.BeanGenDriver.main(BeanGenDriver.java:117)
[java] WLMaker-SubProcess: : Caused by: java.util.zip.ZipException: The system cannot find the file specified
[java] WLMaker-SubProcess: : at java.util.zip.ZipFile.open(Native Method)
[java] WLMaker-SubProcess: : at java.util.zip.ZipFile.<init>(ZipFile.java:203)
[java] WLMaker-SubProcess: : at java.util.jar.JarFile.<init>(JarFile.java:132)
[java] WLMaker-SubProcess: : at java.util.jar.JarFile.<init>(JarFile.java:97)
[java] WLMaker-SubProcess: : at weblogic.management.commo.BeanGenDriver.getManagementTempDir(BeanGenDriver.java:90)
[java] WLMaker-SubProcess: : ... 1 more
[java] WLMaker-SubProcess: : Stopped draining WLMaker-SubProcess:
[java] WLMaker-SubProcess: : Stopped draining WLMaker-SubProcess:
[java] BeanGen code generation failed
[HUDSON] Archiving C:\hudson\jobs\albpm_ip-identity-asserter_-Build\workspace\pom.xml to C:\hudson\jobs\albpmip-identity-asserter_-Build\modules\dk.skat.ip.integration.albpm$ip-identity-asserter\builds\2010-11-2213-41-28\archive\dk.skat.ip.integration.albpm\ip-identity-asserter\1.2\pom.xml
[INFO] ------------------------------------------------------------------------from my experience, using weblogic jars can be a pain if the full install is not on the local box.
Note that you dont have to 'install' it. Just copy the directory.
Reason is that the jar files have manifests with relative classpaths.
For an example of horror take a look at the weblogic.jar MANIFEST's classpath entry.
-Fred -
So whenever I try to download the newest itunes file it won't let me finish the install process because I'm missing the "Itunes.msi" file whatever that is and I've done some searches but I cannot find the file. Anyone know what to do?
you can try this thread maybe? https://discussions.apple.com/message/16217061#16217061
-
When I start Firefox, the following message appears before the home page opens:
"COMMONSHELL: McShield.dll
The specified resource language ID cannot be found in the image file.
McShield.dll: The system cannot find the file specified."
I click OK, Firefox opens normally and everything seems to operate as expected, no further problems.hello, the error message is obviously coming from one of the installed mcafee extensions. please directly contact mcafee technical support - they can likely give you more detailed guidance and are the only ones who can fix bugs or make necessary adjustments in the addon.
-
Photosmart C4780 install fails at "system cannot find specified file"
My problem started simply with the printer, an HP Photosmart C4780 which has always had a wireless connection and would not print. At first, the network connection checked out fine from the printer control panel. I ran a Microsoft printer troubleshooter, which found a block in the print queue, and cleared it. The first test page would not print, but the "inner test page" did print. I didn't understand whatever that meant, so I looked for help from the HP site.
I ran the HP Print and Scan Doctor, and it suggested I reinstall the driver. I downloaded and saved the current one from HP (PS_AIO_06_C4700_USW_Full_Win_enu_140_175.exe) and then uninstalled the existing driver. When I attempted to install the new one, a window popped up saying, "The system cannot find the specified file," with only one box to click which said simply "OK". The installation went through to "review installation options", after which came “checking updates, downloading updates, installing updates” and then it was while “checking system” that the “cannot find the file” window popped up, and when I clicked “OK”, the installation window as well as the error message box, just disappeared. What I assume was the file path was in the frame of the window, but the whole thing didn't fit so it didn't show the end. What I could read was “C:\Users\ … \Local\Temp\7zS588E\Setup\.\Setup\hpzpnp40 …
I found one topic on the same problem for the same model printer in the forum, which offered this fix:
You will need to first complete a level 3 uninstall of the software. I have included the steps below for this.
1. Press the Windows key, and the letter R
2. Type %temp%, and click OK
3. Open the 7z folder (most recent one if there are multiples)
4. Open the util folder
5. Open the ccc folder
6. Double click on the Uninstall_L3
Once the Uninstall_L3 has completed, please delete all items listed in the temp folder. Note, you will not be able to to delete all items, please skip the ones that you cannot. Next please empty the trash, and perform a clean boot. I have included the document 'How to perform a clean boot in Windows'. If your computer does not request it, please restart your computer.
Once your computer is back up, you will need to reinstall the printers software. You can either do this by using the Installation CD, or downloading the software.
I did what was suggested, until it got to the point where it said it did not recommend removing any further items if I intended on using the HP Officejet printer (yes I have a second HP printer attached to the network) anytime in the future. Not really understanding how this all works, I decided to stop what I was doing, so unfortunately it did not solve my problem.
Do I need to uninstall both HP printers before I can reinstall one? And if I do that, is there any reason I would not be able to reinstall both printers? Sounds like I'm asking for trouble. Bottom line... I still cannot install the driver.
I have tried to install both the full and basic versions of the driver and always get the same result.
I have an HP Pavilion dv6-3100t notebook, running Windows 7 Home Premium, version 6.1.7601 service pack 1, 64 bit. I haven't installed any new hardware or software. This printer has always had a wireless connection. The router I use is a Netgear 54 Mbps WGR614 v6 (supplied by my cable company), and the network includes not only my notebook and the Photosmart printer, but also an ASUS desktop, another HP printer, an Officejet 6300 series (used only for printing graphics and photos with a wired connection to the router), and a Vizio smart-TV. I use Norton 360 Premier Edition and disabled the anti-virus auto-protect when I downloaded and attempted to install the driver.
Please help! And thanks in advance for your time and attention.
This question was solved.
View Solution.Hi wakey-wakey,
I would recommend accessing your Temp folders, rename a Temp folder to 7zS588E and run the installation from that folder.
Please keep me posted.
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green. -
Upgrading from MBAM 1.0 to 2.5 on the Administration and Monitoring server (database server already upgraded). To upgrade the administration server, I uninstalled MBAM 1.0 -> Deleted the MBAM website from IIS manually -> Reboot -> Installed MBAM
2.5. After upgrade if I go to selfservice portal via
https://myserver.mycompany.com/selfservice, I get this error:
Server Error in '/SelfService' Application.
Could not load file or assembly 'System.Web.WebPages.Razor,
Version=2.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35' or one of its
dependencies. The system cannot find the file specified.
Description:
An unhandled exception occurred during the execution of the current web
request. Please review the stack trace for more information about the error and
where it originated in the code.
Exception Details:
System.IO.FileNotFoundException: Could not load file or assembly
'System.Web.WebPages.Razor, Version=2.0.0.0, Culture=neutral,
PublicKeyToken=31bf3856ad364e35' or one of its dependencies. The system cannot
find the file specified.
Source Error:
An unhandled exception was generated during the execution of the
current web request. Information regarding the origin and location of the
exception can be identified using the exception stack trace below.
Stack Trace:
[FileNotFoundException: Could not load file or assembly 'System.Web.WebPages.Razor, Version=2.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35' or one of its dependencies. The system cannot find the file specified.]
System.Web.Mvc.PreApplicationStartCode.Start() +0
[InvalidOperationException: The pre-application start initialization method Start on type System.Web.Mvc.PreApplicationStartCode threw an exception with the following error message: Could not load file or assembly 'System.Web.WebPages.Razor, Version=2.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35' or one of its dependencies. The system cannot find the file specified..]
System.Web.Compilation.BuildManager.InvokePreStartInitMethodsCore(ICollection`1 methods, Func`1 setHostingEnvironmentCultures) +12980619
System.Web.Compilation.BuildManager.InvokePreStartInitMethods(ICollection`1 methods) +12980328
System.Web.Compilation.BuildManager.CallPreStartInitMethods(String preStartInitListPath, Boolean& isRefAssemblyLoaded) +280
System.Web.Compilation.BuildManager.ExecutePreAppStart() +172
System.Web.Hosting.HostingEnvironment.Initialize(ApplicationManager appManager, IApplicationHost appHost, IConfigMapPathFactory configMapPathFactory, HostingEnvironmentParameters hostingParameters, PolicyLevel policyLevel, Exception appDomainCreationException) +1151
[HttpException (0x80004005): The pre-application start initialization method Start on type System.Web.Mvc.PreApplicationStartCode threw an exception with the following error message: Could not load file or assembly 'System.Web.WebPages.Razor, Version=2.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35' or one of its dependencies. The system cannot find the file specified..]
System.Web.HttpRuntime.FirstRequestInit(HttpContext context) +12979668
System.Web.HttpRuntime.EnsureFirstRequestInit(HttpContext context) +159
System.Web.HttpRuntime.ProcessRequestNotificationPrivate(IIS7WorkerRequest wr, HttpContext context) +12819261
Anyone know how to solve this? Thanks in advanceSorry for late response. I fixed the issue by installing the correct version of ASP .NET 4 from
here.
If .NET Framework 4.5 is already installed, also run aspnet_regiis -i from C:\windows\microsoft.net\Framework\v4.0.30319
Maybe you are looking for
-
T400 to Sony Bravia KDL46EX500
Hi - I am trying to have my T400 play movies or TV shows from the internet to my Sony Bravia KDL46EX500. As described in the TV manual, I connect a 15 pin cable to the VGA output on the laptop and plug the other end into the RGB input on the TV. I
-
How to Download a Hierarchie to a Flat File
Hallo Experts, sorry i just have a second question. We make the solution "How to Download a Hierarchy to a flat file" Program works transport green Upload ok, but the Text Node keys are there, but not the text e.g. description text note short: 000000
-
Compiling JavaFX and Java into a single JAR
Perhaps I am missing something, but is there a simple way to compile both Java and JavaFX sources into a single JAR? The issue is cross references between Java and JavaFX. Using javac or javafxc separately, cross references are handled by the compile
-
Import data and cofiles via stms
Hi all, I would like to import some data and cofiles via stms in my MiniSAP. Only tables are imported without problems. Programs, transactions or other files of the package will not imported. The imported objects will be not activate automatically. T
-
Using ChaRM in specific projects
Hi all, We are configurating ChaRM 7.1, SP8. In begining we would like to turn on ChaRM controls in some projects, like pilot. We want to work with some Project without ChaRM´s controls, with manually transport. After this we will use ChaRM controls