AP express PPPoE problem

Hi,
I have problems connecting my APe to the internet with PPPoE.
Normaly my APe is configured as a wireless client of my
existing network only used for airtunes.
Now I want to use the APe at another place as DSL-router. So
I´ve setup a new profile using following config:
Wireless Mode: Create a Wireless Network (Home Router)
Internet Connect using: PPPoE
Network: Share a single IP address (using DHCP & NAT)
Connection to the new wireless network an the APe works
fine: I get an IP from the APe and can ping the APe
If I connect the APe to my DSL-Modem (ethernet modem, not
usb), the light gets green but I´m not connected to the
internet.
I´ve validated the PPPoE login with another router.
I´ve reset the modem and APe several times.
I´ve reset the APe th factory defaults and create an new
config.
I´ve setup a syslog-daemon and set syslogging to debug on
the APe, but only got following messages:
ppp: Connecting via ethernet (user "MYUSERNAME" service "").
ppp: Connecting via ethernet (user "MYUSERNAME" service "").
ppp: Connecting via ethernet (user "MYUSERNAME" service "").
Firmware: Apple Base Station V6.3
Does anyone have a tip to solve this problem?
Thanks
carsten
Windows XP Pro

I don't know that much about Windows. I will only setup a shared folder for my clients who have a Windows laptop from work to share docs with their Mac at home. What I have found to work is to setup the Base Station to connect to the ISP (if they use PPPoE) via PPPoE (Point To Point Protocol over Ethernet) and then set the computer so that it will not attempt to connect to the base station via PPPoE. In the Mac operating System there is a check box that says "connect via PPPoE". I uncheck that box. If that box in OSX is checked it will continue to try to make the connection to the ISP and always fail. Their must be some kind of conflict. There may be a different way of doing it but I am not aware of it. I am sticking to what works and the above works without any problems. As I said I am not that familiar with Windows at this point so I don't know what choices are available when setting up the computer. With Boot Camp coming out I may have to delve a little deeper into it as I am sure that I will have clients asking me to setup a partition on their drive in order to run Windows. My question is are you using PPP on a dialup? If you are on dialup then that is a different story. If you mentioned a dialup connection on your post, then I missed that and I apologize.
Rog

Similar Messages

Belkin wireless modem and Airport Express lan problems

Let me preface my problem by stating the obvious - I'm not very technically proficient!
That said, I've had an AirPort Express wireless lan connecting three computers on my home/office network for the past 8 months without any problems at all. All machines on the network have been able to access the internet via a Thomson SpeedTouch 530 ADSL1 modem that connects via an ethernet cable to the AirPort Express. No problems.
The network consists of my G5 iMac (ALS), my husband's Mac mini and my Sony VAIO laptop (XP Pro SP2).
I should also mention that half-way between my office and my husband's office there is a second AirPort Express that 'boosts' the signal to his office.
I recently changed ISPs to a provider that offers the faster ADSL2+ service. This meant that I had to get a new Belkin ADSL2+ modem. This is my problem. I cannot connect my AirPort Express network to the internet using the Belkin modem. The Belkin modem connects without any problem if I just have it connected via ethernet to my iMac but that's not what I want to do.
My existing AirPort details are -
IPv4 Address: 10.0.1.3
Router 10.0.1.1 (this is the SpeedTouch 530 modem)
Subnet Mask 255.255.255.0
I thought I could change the new modem's address(?terminology?) from 10.1.1.1 (which is how it came) to 10.0.1.3 and that everything would work but it doesn't.
Belkin tech support said 'the problem is with your AirPort Express' (what else would they say)?
Do I have to keep the 10.1.1.1 and change my AirPort addresses? Or should I try to set up a new network?
2GHz 20-inch iMac G5 (ALS) Mac OS X (10.4.4) Mac Mini; 12inch PowerBook; 120GB external firewire hd; Video iPod; iPod mini;

No ideas?

Weird PPPoE problem with new Time Capsule

OK, so this is a long and tedious saga, but I don't know what details are important and what are irrelevant.
I had an old AirPort Extreme which was giving me problems. I could connect to the internet fine when I connected my MacBook directly to the DSL modem via the Ethernet cable, but when the same cable was plugged into my old AirPort it thought that there was no Ethernet cable connected to the WAN port. The AirPort was over five years old, so I figured that it was just past its time, and I kinda wanted a Time Capsule anyway for wireless backup, so I went to the Apple Store and bought one today.
I just tried to set it up, and AirPort Utility is telling me, "This Apple wireless device is set up to connect to the Internet using PPPoE but no PPPoE server can be found. Make sure your Internet service provider requires that you use PPPoE, and make sure that the modem is turned on and connected to this Apple wireless device's WAN port and try again. If you still can't connect to the server, contact your service provider."
Well, I did contact my ISP (AT&T Yahoo!), and they said that if I can connect directly via Ethernet, the problem has to be with the Time Capsule or its settings, so they can't help me. I've tried power cycling the DSL modem and Time Capsule, and I keep getting the same problem. Does anyone have a clue what might be going on? (I'll probably call AppleCare when they're open, but I thought someone here might be able to shed some light on the situation.)
Thanks!

I had a similar problem (to name one) and couldn't resolve it... I packed it back up and am returning it tomorrow.
All these people have all these solutions but none of them should have to do any of it! That is the biggest problem I have with the TC. They give you a small little guide to set everything up and it doesn't deal with any of this. With networks and computers as they are right now.... you should not have to do any of this at all. You should be able to plug it in, answer a few easy to answer questions like it does ask and then it should configure itself just as any other network device I have purchased in the last 2 years. Even my PS3 I bought last week did it by itself by only asking a few questions! (Same as my macbook... so you know they can do it)
Now.. say you do get it all set up and it works great... hope you don't have kids that like to play their XBox 360 online because guess what.... it isn't compatible with the TC wireless!!! If you want to use your PS3.... you have to buy more stuff.
No.... do yourself a favor... go buy the D-Link DIR-655 that has a USB storage link... hook it up and be in business in 10 minutes. You can also get a 1TB WD external hard drive for $209.00 and hook it up direct to your mac and use time machine and transfer files faster than a mule walking up hill.

SQL Server 2008/2012 Express Connection Problem

Hello,
since a couple of days I'm working on a problem with the SQL Server Express (32-Bit as well as 64Bit).
I installed a new SQL Server 2008 with an instance named SQL2012 and the Management Studio 2008 R2 on the same machine. I easily am abled to connect to the Server using the Management Studio with several Server Name settings (localhost, IP, (local), .\SQL2012).
Now I have a self-written programm (C#) wich should connect to the Server, but it does not work. It is definitely not a problem of the programm code because the same programm is abled to connect to a SQL Server 2008 Enterprise Edition. Similar Problem with
the 2012 Express Version (2012 Enterprise not tested).
The connection string I use and wich is working with connecting on the Enterprise Edition is: Server=Servername\Instance;Database=DatabaseName;User Id=user;Password=password;
Anybody any solution why the Express-Version refuses to connect?
(Sorry if I have made several failures in my text, English is not my native language)

It Occurs when I try to ping.Send the Server to see if he is active. If I skip this step and try to connect directly to the server (con.Open()) I get the exception:
A network-related or instance-specific error occurred while establishing a connection to SQL Server. The
server was not found or it can not be accessed. Verify that the instance name is correct and that SQL Server allows remote connections. (provider: Named Pipes Provider, error: 40 - Connection with the SQL Server couldn't be opened)

G4 and Final Cut Express installation problems

Thank you in advance for any help you can send my way. Any will be greatly appreciated.
I have a PowerMac G4 (gray) tower. Recently, under the advice of a Mac tech, I installed a 200GB harddrive and a Sonnet's Tempo ATA133 PCI card so that I could successfully install and run FinalCut Express. Now not only do I have the previous installed but I also have 1GHz CPU Speed, 1GB of RAM, DVD/Superdrive, Mac OS 10.4.3 and more than enough memory for the installation.
So now for the two strange parts:
1) When trying to install Final Cut it says that I cannot install the software because I lack the hardware.
2) And now I noticed in my System Profiler it says that my Machine Name is "Power Mac G3 (PCI graphics)" which I know it is not!
Do I have the wrong PCI card? Did I install it wrong? Am I missing something?
For your reference, listed below is what is required to run Final Cut Express:
Minimum Hardware Requirements
• A Macintosh computer with a 500 MHz or faster PowerPC G4 or G5 processor (550 MHz for PowerBook G4, 450 MHz for dual-processor Power Mac G4 or G5) and an AGP (Accelerated Graphics Port) graphics card compatible with Quartz Extreme
• 384 MB of RAM (512 MB required for RT Extreme and Soundtrack)
• For HDV: A Macintosh computer with a 1 GHz or faster PowerPC G4 or G5 processor and 1 GB of RAM
• 1 GB of available disk space for application installation
• 5 GB of available disk space for Soundtrack content
• 9 GB of available disk space for LiveType content
• DVD drive for software installation
Minimum Software Requirements
• Mac OS X 10.3.7 or later
• QuickTime 6.5.2 or later
Thanks again.

HI Coyote,
This could prove to be a problem. You definitely need 65MB of VRAM to run FCP. And FCP is a fairly sophisticated video editing program and takes time to learn. Unless the iBook has DVD burn capability, which I doubt, even with an older version of iLife, you wouldn't be able to burn to DVD's. But you could use iMovie, which is part of iLife to view video that's been uploaded to the iBook. Another potential problem is, I think this particular iBookG4's factory drive is 60GB. Video editing requires huge amounts of drive space to run without crashing. iLife 05 requires 4.3GB of drive space. iLife 05 requires 256MB of RAM, but runs much more efficiently with 512MB.
So, you have several glitches. Limited drive space, limited memory, insufficient VRAM, and no DVD burn capability. You wouy also need a camcorder that is compatible with the iBookG4.
I wish I had better news... here is a link to Apple's information for minimum requirements for iLife 05: http://docs.info.apple.com/article.html?artnum=306338
Carolyn

Airport Express speaker problem

I have an Airport Extreme running my home network with two Airport Expresses, both hooked up to powered speakers. One Express is the older model, the other brand new. AirTunes intermittently drops one or the other speaker setup. My question is this- would I potentially fix this problem by upgrading the older Express to a new one? Thanks!

My question is this- would I potentially fix this problem by upgrading the older Express to a new one?
If all of your wireless client support 802.11n, then the answer would be yes. In that case you could create an 802.11n only network to get the best bandwidth possible for streaming.

Multiple airport express airtunes problem

Hi,
I have my wireless network setup, using my AirPort Extreme with 802.11n to create the wireless network, then i have a new AirPort Express (with 802.11n) and an old AirPort Express (not 802.11n).
The two additional AirPort Expresses i have setup to connect to the wireless network, they all look fine and return the green light - but my problem is, that i am only able to select the new AirPort Express in my iTunes (as external speekers) - i can not get it to show me the old AirPort Express
It is kindof sad, now my old AirPort Express is useless - the point was that i should be able to have them both as external audio targets for my iTunes...
I hope you guys can help me.
Kind regards,
Rasmus Burkal, Denmark

Hi again Bob,
Just one thing i find "funny" - you know, in the AirPort tool, you can go and change the settings of a AirPort device. If I go to the "new" Express, I can change the "name" of the iTunes speakers (the name that apear in my iTunes drop-down) - but when I try to do that at the "old" Express, when I click update - I gives me a warning - saying something like "not supported by this wireless apple device" (even though the setting is avalible from the AirPort tool)
All the best,
Rasmus

Aiport Express Sharing problem.

I'm having trouble getting my Airport Express to broadcast my internet. Here is the current set up. The internet modem is connected to an ethernet switch, so that my roommates mac desktop can be hardwired(no wireless) and so i can connect the airport to the switch to broadcast for me(on my laptop pc). However right now we can only get it to give internet to either the aiport or her computer, not both at once. Is this a problem with the way i've got it set up or just logistically not possible? Trying toget the internet to share, which with the switch it should theoretically share it. Thanks for your help.

Hello eDahl87. Welcome to the Apple Discussions!
The problem is that the modem is expecting to only see one device connected to it. When connecting either an Ethernet hub or switch directly to the modem, the modem sees multiple devices ... and why you're having the problem.
One option would be to configure your laptop PC for Internet Connection Sharing. In this case you would connect your laptop wirelessly to the AirPort Express Base Station (AX), and provide Internet access via your laptop's Ethernet port to your roommate's Mac.
Your network configuration would look something like the following:
Internet modem > (Ethernet cable) > \[Ethernet port] AX > (wireless) > laptop PC \[Ethernet port] > (Ethernet cable) > \[Ethernet port] Mac

HELP - SQL Server Express Install Problems

The SQL Server Express completed without error. However, when I tried to connect to the SQLEXPRESS instance I received one of those wonderful MS errors, "Specified file not found". WHAT FILE? (After all these years MS still can't figure out how
to give an error msg. that provides some hint of what's wrong.) Going on, I started the install console and selected the REPAIR option. (It didn't ask what the problem was, it just ran.) It did ask what instance needed repair. I told
it SQLSERVER. It proceeded to repairing it. My first hint that their repair function worked as well as their error handling was when I got the: That share name has already been used (or something like that) error (notice, MS didn't tell me what
share name, or what aspect of the db they were talking about). After pressing OK, the REPAIR function proceeded to run to completion. When I reviewed the REPAIR report I found that three db processes all had the same SHARE NAME ALREADY USED error.
Actually, I thought that it was no big deal. If this was a real REPAIR, it shouldn't matter that the name was already used because everything else should be the same. (I know I'm nigh eve about the
Intricacies of SQL server.) After repairing my installation, I brought up the SQL Server Management Console again. This time, it did not display SQLEXPRESS in the Connect field. I selected the drop down list arrow to see if it was
listed and the list was blank so I entered SQLEXPRESS in the connect field and clicked on the CONNECT button. I got a NETWORK PATH NOT FOUND error. So, before I really mess things up, I thought I should ask if anyone knows what I should do
next. (As an aside, I've pressed the MS Error Message HELP button numerous times abut various errors I've received over the years. Not only are MS error messages useless, their Help Page has never ONCE been able to provide any information
about the encountered error. MS should spend some time and develop some truly helpful error messages as "File not found" and unknown error code 837289 are absolutely useless and especially since their HELP PAGE is never able to provide any
information either. I do wonder how I can get Unknown Error codes from people who wrote the code that raises the error. Don't they document anything?)

I did read the requirements and made sure I met them all. The install package I used was: SQLEXPRADV_x64_ENU.exe. You're correct. I'm not familiar with SQL Server.
I downloaded SQL Server Express and Visual Studio Express to learn and explore because I wanted to learn about the new technology.
After leaving my message, I did some more studying and playing with the system. I managed to figure out that I had to turn on the data base service before I could connect with it. I'm sorry, I don't understand how Microsoft could install a data
base system without turning on its services. Why would I want to install something and NOT use it? The default should be ON and the setup manager should provide a choice to set it to OFF on the configuration page.
My experience is rather dated. I had to retire due to a disability in 2005. I couldn't control my arms and hands. The doctor recently tried a medication again that I had had a severe negative reaction to. He first administered steroids
and started me on a small dose and titrated it up as I was able to handle it. Now I have some days where I have pretty good control — I can print a little but can't write well and other days where I can't print, write, or feed myself.
I have performed many functions. I have been an analyst, a programmer, a data base designer, and a college professor at three different colleges. I've done extensive work in process automation and have even automated the management functions
for a data base system that was used to schedule every aspect of all the aircraft, ranges, and weapons development processes on Eglin AFB. I also wrote major pieces of the code used by the system and trouble shot and corrected functions written by other
programmers. The system supported over 300 users a day on two bases. Unfortunately it was developed in Fortran on a VAX and with VB6 and MS Access using VBA, Queries, Tables and Forms on networked PCs.
I plan to do a lot of reading. I'll also be looking at the Microsoft sites for a sample DB and lessons to go with it. I am a little frustrated with how information is organized on the web. The other night I needed to find some information
about something from Microsoft. It took me almost two hours to ask my question in such a way that MS was able to provide what I wanted. I kept asking essentially the same thing, but I had to use the exact phrase MS used on the page. I know
MS is big and they support multiple generations of each product. They have an almost impossible task. I just have to find the various product entry pages.
Thanks for offering your help.

HUGE Outlook Express database problems!

I had a hard drive failure. The problem is that my Outlook Express Identities folder was stored there. I recovered the Identities folder using Data Rescue and I discovered that the file called "database" is truncated.
I can do a rebuild of the database but then all several thousand emails are missing. After some trial and error, I confirmed that it is the database file that is screwed.
I can use a backup file from 10 months ago but then the last 10 months of emails are missing.
Database - 70 MB
Database Cache - 20 KB
Messages - 750 MB
I think everything I want is in the larger Messages file even though I also see messages inside the Database file. (I'll never understand the MS programming philosophy)
Are there any Mac utilities that will extract the emails from these database files?
What about my damaged database file? Since it's truncated, is there anything I can splice to the end of it to fool Outlook Express into properly rebuilding it?
Can these be transferred to a PC and then repaired using one of the dozens of Winbloze utilities available for database repair and then converted back?? If so, how?
I'm stumped and I'm hoping anyone here can help.
Thank-you.

I never had a problem with OE, but it uses the same
MS programming philosophy as entourage, where I do
know you can't get out of a truncated databse…
Sorry, and if the automatic Rebuild routines won't
fix it, it's just gone.
Not quite...
I was able to recover about 99.9999% of the 28,000 "lost" emails using a neat little utility called "Emailchemy".
It scours nearly any email database file in almost any condition, pulls out the messages, and then saves them ALL to a generic mbox file that ANY email program can read. It also preserves the attachments!
FYI- For Outlook Express in OS 9, the file called "Database" contains all the outgoing emails and attachments. The file called "Messages" contains all the incoming emails and attachments.
I just ran Emailchemy on both of them and imported two mbox file into Entourage for OS X. That created two folders, each containing all the messages PLUS attachments from each of the two files.
In Entourage for OS X, ALL incoming and outgoing emails plus attachments are stored in the file called "Database". For this program, there's no such thing as "Messages" file.
So anyone reading this, DO NOT delete your corrupted Microsoft email database files, lock them, back them up, and do NOT give up hope. Even if you couldn't extract the information, you can still open the file in a text editor and see your messages inside (minus the attachments, of course). As horrific as this process may sound, at least you can search for something specific if needed.

MeetingPlace Express strange problem !

Environment:
MeetingPlace Express 1.1.1.11
CallManager 4.1(3)sr2
Voice Gateway 1: 2821 (c2800nm-advipservicesk9-mz.124-4.T.bin) + VIC2-4FXO
Voice Gateway 2: 2621XM (c2600-advipservicesk9-mz.123-14.T5.bin) + NM-2V + 2* VIC-2FXO
VG1 connect to CallManager using H.323, VG2 connect to CallManager using MGCP
MeetingPlace Express connect to CallManager using H.323.
Problem:
When dial-in from PSTN to VG1 and VG2, both are well; but when using "Find-Me" feature, MeetingPlace express dial to user, users via VG2 are can sent dtmf with MeetingPlace Express, but users via VG1 can not sent any dtmf digit to MeetingPlace Express. So users via VG1 can not enter the meeting.

For more information the following url would be useful,
http://www.cisco.com/en/US/products/ps6533/products_installation_guide_book09186a008057b547.html

PPPoE problem with Authorization of the ip-address (Framed-IP)

Hi!
This week I changed our PPPoE dial-in router from a Cisco 3660 (SW: 12.4.25) to a Cisco 2901 (SW 151-2.T2-Universal Image).
Now I have the problem that I could not make a dial-in connection to this router. I get an error in the PPP-Authorization.
I want to get the IP-Address per radiusattribut "Framed-IP-Address". With the version 12.4. it works fine.
DEBUG:
Nov 10 09:35:23.277: ppp29 PPP: Using AAA Unique Id = 104
Nov 10 09:35:23.277: ppp29 PPP: Authorization required
Nov 10 09:35:25.289: ppp29 PPP: Sent PAP LOGIN Request
Nov 10 09:35:25.301: ppp29 PPP: Received LOGIN Response PASS
Nov 10 09:35:25.301: ppp29 PPP AUTHOR: Author Data NOT Available
Nov 10 09:35:25.301: ppp29 PPP: Sent LCP AUTHOR Request
Nov 10 09:35:25.301: ppp29 PPP: Sent IPCP AUTHOR Request
Nov 10 09:35:25.301: ppp29 LCP: Received AAA AUTHOR Response PASS
Nov 10 09:35:25.301: ppp29 PPP: Receive Attrs from[author] Keep[LCP] MERGE
Nov 10 09:35:25.301: ppp29 PPP: Keep Attr: service-type         2 [Framed]
Nov 10 09:35:25.301: ppp29 PPP: Updated the attr service-type in datalist
Nov 10 09:35:25.301: ppp29 PPP: Skip Attr: addr-pool            "pool-edsl"
Nov 10 09:35:25.301: ppp29 PPP: Skip Attr: addr                 213.174.251.199
Nov 10 09:35:25.305: ppp29 IPCP: Received AAA AUTHOR Response PASS
Nov 10 09:35:25.305: ppp29 PPP: Receive Attrs from[SSS] Keep[NCPs] MERGE
Nov 10 09:35:25.305: ppp29 PPP: Skip Attr: service-type         2 [Framed]
Nov 10 09:35:25.305: ppp29 PPP: Keep Attr: addr-pool            "pool-edsl"
Nov 10 09:35:25.305: ppp29 PPP: Updated the attr addr-pool in datalist
Nov 10 09:35:25.305: ppp29 PPP: Keep Attr: addr                 213.174.251.199
Nov 10 09:35:25.305: ppp29 PPP: Updated the attr addr in datalist
Nov 10 09:35:25.313: %LINK-3-UPDOWN: Interface Virtual-Access3, changed state to up
Nov 10 09:35:25.313: Vi3 LCP AUTHOR: Process LCP Author Data
Nov 10 09:35:25.313: Vi3 LCP AUTHOR: Process Attr: service-type
Nov 10 09:35:25.313: Vi3 LCP AUTHOR: Authorization succeeded
Nov 10 09:35:25.313: Vi3 PPP: Store Author Attr: addr-pool
Nov 10 09:35:25.313: Vi3 PPP: Store Author Attr: addr
Nov 10 09:35:25.317: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access3, changed state to up
Nov 10 09:35:25.317: Vi3 IPCP AUTHOR: Start. Her address 0.0.0.0, we want 0.0.0.0
Nov 10 09:35:25.317: % IPCP AUTHOR Vi3: Attributes addr and addr-pool are mutually exclusive
   ---->> I think this is my problem - have anyone an idea?
Nov 10 09:35:25.317: Vi3 IPCP AUTHOR: Authorization denied
Nov 10 09:35:25.317: Vi3 IPCP AUTHOR: Done. Her address 0.0.0.0, we want 213.174.251.199
Nov 10 09:35:25.357: Vi3 PPP: Sending Acct Event[Down] id[104]
Nov 10 09:35:25.365: Vi3 PPP: Clearing AAA Unique Id = 104
Thanks,
Hannes

Hi Shelley!
Thanks for your answer. We have solved the problem.
It was a wrong configuration in the templete.
The attribut "Framed-IP-Address" was configured in the templete and in the default-attributes of the radius-server.
Thanks for help!
Hannes

AirPort Express PPPoE: connection uptime in the bar. How to change?

hi all,
I've just set up a PPPoE connection with my Airport Express, and now I can see connection uptime showing in the bar next to the signal strength. How to hide that counting as it's sooo annoying, but keep the signal icon in the bar?
Thanks!

whoa... OSX is sometimes just to simple for my Windows background & way of thinking.
Thanks Freezing, that option was purely just tooooo simple for me to find it out! ;))
ok, now I know what's the beauty of OSX: simplicity.
cheers!

Java System Communications Express attachment problem

Hello everyone, please excuse my ignorance on this query as I have very little to do with the Java language and I've really approached this forum as I've run out of ideas for the problem my customer has.
The customer is connecting to a 'Sun Java System Communications Express' server, from approximately 20 PC's. 2 of the PC's have a problem that is not user based because if they sign in elsewhere their problem disappears and likewise if someone signs into their PC, they experience the same problem.
If the user receives an email with an attachment and forwards it to a recipient, no problem.
If the user recieves an emal with an attachment and forwards it to themselves, no problem.
If however, the user tries to send an email with an attachment (which for all intents and purposes seems to take the correct amount of time to upload, and when you click save appears in the message attached) the attachment disappears, including if you simply save the message in drafts and do not actually send it.
I have tried uninstalling and reinstalling versions 5 and 6 of Java, resetting the web settings using both IE6 and IE7 (unfortunately the initial secure server refuses any other connections from Firefox / Netscape / Opera / Safari therefore I can only test with IE)
I have disabled all additional addons, disabled all non-microsoft startup services, disabled all startup programs.
As you will appreciate, I've done a fair and reasonable amount of testing and simply cannot work out why the attachment fails to stay with the email on these two machines. Help on this problem would be very much greatly appreciated.
Many Thanks
Tony

Unfortunately I do not have access to version information of the server as I am only have access to the client end. All that I can provide you with is the fact that it works on 18 identical systems. The missing attachment(s) occur regardless of whether you save the message to draft or send the message. It should be noted however that if you receive an attachment with a message and save that to drafts, the message retains the attachment so it only seems as though it is affected during the phase of attaching the file to the message from the local PC. The environment that the client is working in uses a verified certificate and is connected through https.

Oracle Express perfomance problem

Hi, I am facing performance issues with following application in Oracle Express using OFA as front end. There are 9 dimensions in cube and one measure. DB size 18-20 GB. geography and time dimension is dense, all other are composite. Leaf level data for one month and one geography is 50k rows only. It is taking more than 1 hour to run following command.
allstat
lmt geography to 'G036'
lmt time to 'DEC06'
value=na
upd
I have to na the data before uploading new data. could someone pls suggest some better way to na the data, which should be faster?
thanks very much.

The fastest method would be to rename your geography and time dimension values
to a temp value (to be removed on your next eif export/import)
And then add them back and load ..
ie
mnt time rename 'DEC06' 'XDEC06'
mnt geography rename 'G036' 'XG036'
update
mnt time add 'DEC06'
mnt geography add 'G036'
" NO Need TO NA Anything .. just load your data
You could try deleting the members instead of the rename .. but this caused
me some problems in the past .. so i found the rename to work better.
Mike
'

AP express PPPoE problem

Similar Messages

Maybe you are looking for