AP not joining
Hi all,
I could need a little help troubleshooting some AP issue.
For some reason some AP will not join the WLC. (WISMII)
I have several hundrede AP online, but still a few offline
This fails:
FRH-R06-L226-UX-G#sh cdp nei gi2/0/41 detail
Device ID: AP5057.a8a1.c632
Entry address(es):
IP address: 10.61.24.103
Platform: cisco AIR-CAP3502I-E-K9 , Capabilities: Trans-Bridge (why only Trans-Bridge mode and not Capabilities: Router Trans-Bridge)
Interface: GigabitEthernet2/0/41, Port ID (outgoing port): GigabitEthernet0
Holdtime : 161 sec
Version :
Cisco IOS Software, C3500 Software (AP3G1-RCVK9W8-M), Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1) (yes recovery image I know)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 18-Oct-11 15:02 by prod_rel_team
advertisement version: 2
Duplex: full
Power drawn: 14.500 Watts (will it change when AP come online?)
Power request id: 63919, Power management id: 2
Power request levels are:14500 0 0 0 0
Management address(es):
This works fine:
FRH-R06-L226-UX-G#sh cdp nei gi2/0/26 detail
Device ID: AP442b.03c2.638d
Entry address(es):
IP address: 10.61.24.84
Platform: cisco AIR-CAP3502I-E-K9 , Capabilities: Router Trans-Bridge
Interface: GigabitEthernet2/0/26, Port ID (outgoing port): GigabitEthernet0.1
Holdtime : 128 sec
Version :
Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Mon 10-Dec-12 23:33 by prod_rel_team
advertisement version: 2
Duplex: full
Power drawn: 15.400 Watts
Power request id: 45452, Power management id: 2
Power request levels are:15400 14500 0 0 0
Management address(es):
Switchport config:
interface GigabitEthernet2/0/41
description .1X XG-B-41
switchport access vlan 552
switchport mode access
authentication control-direction in
authentication event fail retry 0 action next-method
authentication event server dead action authorize vlan 552
authentication event server dead action authorize voice
authentication host-mode multi-auth
authentication order dot1x mab
authentication priority dot1x mab
authentication port-control auto
authentication periodic
authentication timer reauthenticate server
mab
dot1x pae authenticator
dot1x timeout quiet-period 5
dot1x timeout tx-period 3
storm-control broadcast level 0.50
storm-control multicast level 0.50
storm-control action shutdown
storm-control action trap
spanning-tree portfast
spanning-tree bpduguard enable
end
I have no access to the console interface on the AP at the moment.
any suggestions
/Finn
Well you need to take a look at the AP or console. There have been issues with the 3500's and the white light of death. If you can have someone confirm if the APs led is white or not, that will tell you right away if you need to RMA the ap or not. Other than that, you need to console into the AP and post the output when powering up the AP.
Sent from Cisco Technical Support iPhone App
Similar Messages
-
Does not join to any fact source issue in 10g
HI,
I am getting below issue while compiling rpd.
Logical Dimension Table Dim-XX has a source xx_aa that does not join to any fact source.
Let me describe situation here.
In physical layer , i have one xx_v table . there is no join condition physical layer. But in BMM layer we have created two logical tables for single xx_v table and providing join in bmm layer. When am compiling it i'm getting an error.
The one which i have using current rpd, same rpd in production with out any warnings(Logical Dimension Table Dim-XX has a source xx_aa that does not join to any fact source) and they don't have any logical level mapping in content tab. But i am using same rpd in dev instance getting warnings.
Thanks,
Mal
Edited by: user10675696 on Feb 11, 2013 3:08 AMHi Srini,
Please find the below warning here and we don't have an hierarchy for MTL_SYSTE_ITEMS_B
[39008] Logical dimension table Mtl System Items B has a source MTL_SYSTEM_ITEMS_B that does not join to any fact source.
I am getting this in Dev instance only but not in Production. But one rpd can be used in dev and production instances.
Thanks,
Mall -
I can not join my Apple extreme with the Apple express. I shows a conflict in the network! I've tried everything. How can they join on the same network?
It says that my DHCP has to be changed! How? to what?
It is 802.11g.express. but is set to default by the computer (Macbook Air).
The other is 802.11n. (express)
Extreme is 802.11.g. Is the Main Airport.
It is on ethernet & wep 128 security. -
AIR-CAP3502I-E-K9 does not join preferred controller
I have an AIR-CAP3502I-E-K9 AP that is configured for two WLAN controllers with preferred order. However the AP does not join the primary controller, but uses the secondary one instead. I have a bunch of these AIR-CAP3502I-E-K9s , majority work fine, but three of them not.
I have tried commands according to
https://supportforums.cisco.com/docs/DOC-24917
In the controller's GUI the order is properly configured. I also tried to use 'Clear All Config" option on the controller and configured the AP from the scratch, but this did not help.
Here is what I have
XXXX#sh capwap client config
configMagicMark 0xF1E2D3C4
chkSumV2 30883
chkSumV1 1073
swVer 7.2.111.3
adminState ADMIN_ENABLED(1)
name XXXX
location YYYY
group name
mwarName ZZZZ1
mwarIPAddress 192.168.1.1
mwarName ZZZZ2
mwarIPAddress 192.168.1.2
mwarName
mwarIPAddress 0.0.0.0
ssh status Enabled
Telnet status Enabled
numOfSlots 2
spamRebootOnAssert 1
spamStatTimer 180
randSeed 0xBAC2
transport SPAM_TRANSPORT_L3(2)
transportCfg SPAM_TRANSPORT_DEFAULT(0)
initialisation SPAM_PRODUCTION_DISCOVERY(1)
ApMode Local
ApSubMode Not Configured
AP Rogue Detection Mode Enabled
OfficeExtend AP [0] Disabled
OfficeExtend AP JoinMode[0] Standard
Discovery Timer 10 secs
Heart Beat Timer 30 secs
Led State Enabled 1
Primed Interval 0
AP ILP Pre-Standard Switch Support Disabled
AP Power Injector Disabled
Infrastructure MFP validation Disabled
Configured Switch 1 Addr 192.168.1.2
Configured Switch 2 Addr 192.168.1.1
non-occupancy channels:
Ethernet (Duplex/Speed) auto/auto
*Mar 1 00:14:23.001: %CAPWAP-3-ERRORLOG: Selected MWAR 'ZZZZ2'(index 1).
*Mar 1 00:14:23.001: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 22 12:21:57.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
*Aug 22 12:21:57.581: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
*Aug 22 12:21:57.581: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
My primary one is 192.168.1.1 and secondary is 192.168.1.2, but the AP joins always the secondary one.
The lines above
Configured Switch 1 Addr 192.168.1.2
Configured Switch 2 Addr 192.168.1.1
seem to be suspicious, I would expect the reverse order, but do not know how the code did it.
The only guess is that in the very beginning the AP joined 192.168.1.2, and this was the controller I configured the AP initially from. The AP seems to maybe somehow remember this.
OS version is
swVer 7.2.111.3
Thanks,
VladYes, this is what I am trying all the time - configure the AP to point to the WLCs I want it to join.
Firstly I did through GUI, did not work.
Secondly I used 'Clear All Config" option on the controller and configured the AP from the scratch through GUI, did not work.
Thirdly I tried through command line on the AP, did not work.
I used these commands
XXXX#capwap ap primary-base ZZZZ1 192.168.1.1
XXXX#capwap ap secondary-base ZZZZ2 192.168.1.2
XXXX#sh capwap client config
configMagicMark 0xF1E2D3C4
chkSumV2 30883
chkSumV1 1072
swVer 7.2.111.3
adminState ADMIN_ENABLED(1)
name XXXX
location YYYY
group name
mwarName ZZZZ1
mwarIPAddress 192.168.1.1
mwarName ZZZZ2
mwarIPAddress 192.168.1.2
mwarName
mwarIPAddress 0.0.0.0
ssh status Enabled
Telnet status Enabled
numOfSlots 2
spamRebootOnAssert 1
spamStatTimer 180
randSeed 0xBAC2
transport SPAM_TRANSPORT_L3(2)
transportCfg SPAM_TRANSPORT_DEFAULT(0)
initialisation SPAM_PRODUCTION_DISCOVERY(1)
ApMode Local
ApSubMode Not Configured
AP Rogue Detection Mode Enabled
OfficeExtend AP [0] Disabled
OfficeExtend AP JoinMode[0] Standard
Discovery Timer 10 secs
Heart Beat Timer 30 secs
Led State Enabled 1
Primed Interval 0
AP ILP Pre-Standard Switch Support Disabled
AP Power Injector Disabled
Infrastructure MFP validation Disabled
Configured Switch 1 Addr 192.168.1.2
Configured Switch 2 Addr 192.168.1.1
non-occupancy channels:
Ethernet (Duplex/Speed) auto/auto
XXXX#sh log
Syslog logging: enabled (1 messages dropped, 8 messages rate-limited,
0 flushes, 0 overruns, xml disabled, filtering disabled)
Console logging: level debugging, 61 messages logged, xml disabled,
filtering disabled
Monitor logging: level debugging, 0 messages logged, xml disabled,
filtering disabled
Buffer logging: level debugging, 67 messages logged, xml disabled,
filtering disabled
Logging Exception size (4096 bytes)
Count and timestamp logging messages: disabled
Trap logging: level emergencies, 0 message lines logged
Logging to 255.255.255.255(global) (udp port 514, audit disabled, link down), 0 message lines logged, xml disabled,
filtering disabled
Log Buffer (1048576 bytes):
*Mar 1 00:00:09.424: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:09.434: *** CRASH_LOG = YES
*Mar 1 00:00:09.434: 64bit PCIE devicesSecurity Core found.
Base Ethernet MAC address: E0:5F:B9:A8:00:7F
*Mar 1 00:00:12.482: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:13.731: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:13.797: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:16.996: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:17.052: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)
*Mar 1 00:00:17.068: status of voice_diag_test from WLC is false
*Mar 1 00:00:19.182: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 12.4(25e)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Fri 14-Sep-12 19:13 by prod_rel_team
*Mar 1 00:00:19.182: %SNMP-5-COLDSTART: SNMP agent on host XXXX is undergoing a cold start
*Mar 1 00:13:33.342: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:13:33.342: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:13:33.493: status of voice_diag_test from WLC is false
*Mar 1 00:13:33.632: %SSH-5-ENABLED: SSH 2.0 has been enabledlwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:13:33.956: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:13:34.343: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:13:34.343: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:13:36.029: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:13:41.484: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.1.21, mask 255.255.255.0, hostname XXXX
*Mar 1 00:13:51.981: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:14:01.997: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:14:06.099: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:14:07.190: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:14:08.191: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:14:08.288: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:14:09.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:14:11.000: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:14:23.001: %CAPWAP-3-ERRORLOG: Selected MWAR 'ZZZZ2'(index 1).
*Mar 1 00:14:23.001: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 23 06:07:13.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
*Aug 23 06:07:13.578: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
*Aug 23 06:07:13.578: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
*Aug 23 06:07:14.025: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Aug 23 06:07:14.091: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Aug 23 06:07:14.094: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller ZZZZ2
*Aug 23 06:07:14.154: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
What I think might be the key to the problem is this
Configured Switch 1 Addr 192.168.1.2
Configured Switch 2 Addr 192.168.1.1
This is not changing no matter what I do.
Thanks,
Vlad -
AIR-LAP521G-E-K9 is not joining WLC4402-12
Hi,
Please I need some help with any guide or info regarding my LAP521 access points that are refusing to join the WLC4402-12.
This is my first lightweight access point implementation and I have 3 LAP521's and 1 AIR-CAP3502I-E-K9 access points on my network.
They are meant to pick up ip address from external dhcp server and then join the WLC but only the 3502i joins successfuly while the 521's get dhcp address but do not join the WLC. From the logs, I can see that the WLC is discovered by the 521's and even get a response message from the controller but they are still unable to join as shown in the screenshot below.
My WLC is running software version 7.0.230.0 and the 521's are running an lwapp image version 4.2.61.8.
Base Radio MAC
AP Name
Status
Ethernet MAC
IP Address
Last Join Time
00:23:04:cc:56:d0
NA
Not Joined
00:00:00:00:00:00
172.31.5.115
00:23:04:f2:8d:10
NA
Not Joined
00:00:00:00:00:00
172.31.5.113
00:23:33:22:3d:b0
NA
Not Joined
00:00:00:00:00:00
172.31.5.110
3c:ce:73:94:b4:d0
AP001
Joined
44:2b:03:6d:5d:50
172.31.5.120
Oct 01 18:01:17.713
Please any suggestions or help with resolving this issue will be appreciated.
ThanksThe reason the 521 will not join, is because they require the Cisco Express WLC. They will not join the 4400 WLC. Take a look at this matrix with the code you are running and the AP's that are supported.
http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html#wp81600
Sent from Cisco Technical Support iPhone App -
hello
i have a an iPhone 5 .i updated it in the end of summer or begin of fall because i forget the number of version.it is important that i update my i Phone by itself not with iTune . after that my device can not join to wifi to internet but another of app works properly and cellular can join to internet . i reset my i phone in the setting . general section but my problem is remaining .is possible that to return to older version? if there is any solution share with me and i be very thankfulness of you.tanks againIt is not possible to downgrade to an earlier version.
Have you tried the tips on this help page? iOS: Troubleshooting Wi-Fi networks and connections
And you dont need iTunes to update you're device. You can update it OTA in Settings > General > Software Update -
hello
i have a an iPhone 5 .i updated it in the end of summer or begin of fall because i forget the number of version.it is important that i update my i Phone by itself not with iTune . after that my device can not join to wifi to inter net but another of app works properly and cellular can join to internet . i reset my i phone in the setting . general section but my problem is remaining . if there is any solution share with me and i be very thankfulness of you.tanks againIt is not possible to downgrade to an earlier version.
Have you tried the tips on this help page? iOS: Troubleshooting Wi-Fi networks and connections
And you dont need iTunes to update you're device. You can update it OTA in Settings > General > Software Update -
Could not join "wifi network name". A connection timeout occurred.
Mac Pro running 10.7.5.
Whenever the computes wakes from sleep or logs in, it no longer automatically connects to my wifi network. When I manually select the network for from the Wi-Fi status in the menu bar, I get the following message: Could not join "wifi network name". A connection timeout occurred.
Even though I get that message the machine joins the network with no other problems. I am led to believe that is is on the Mac Pro as my Macbook and iPad/iPhone join the network with no issues.
I have tried deleting and restoring the preferred network, and remember networks is checked. I have also restored my airport express base station.
Any suggestions?Hello,
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.5, 10.6, 10.7 & 10.8…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
If using Wifi/Airport...
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed. -
Problem with wifi roaming - printer does not join SSID
In WiFi network with 2 APs with same SSID and security setup (WPA2) working well in roaming for PCs,
samrtphone and MacBook HP printer does not join WLAN and wireless test page from the printer shows as reason that priner see more then one AccessPoint with same SSID.
Product name HP Deskjet 3070 All-in-One Printer - B611a
Model CQ191B
Serial CN192332K805MQ
Service ID 22114
Firmware version MUM1FN1117BR
Region EuropeAssuming that one of the APs runs DHCP and that the other is bridged, turn the briged AP off. Now, connect the printer to the other AP, even if you have to move the printer.
Once the printer is connected it should work fine once you turn the second AP back on.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP -
Consistency Warning - [39008] Dimension Table not joined to Fact Source
I have a schema in which I have the following tables:
A) Patient Transaction Fact Table (i.e. supplies used, procedures performed, etc.)
B) Demographic Dimension table (houses info like patient location code)
C) Location Dimension table (tells me what Hospital each unique Location maps to)
So table A is the fact, and table B is a dimension table joined to table A based on Patient ID, so I can get general info on the patient. This would allow me to apply logic to just see patient transactions where the patient was FEMALE, or was in the Emergency Room, by applying conditions to these fields in table B.
Table C is a simple lookup table joined to table B by Location Code, so I can identify which hospital's emergency room the patient was located in for instance.
So the schema is: A<---B<---C, where B and C are both dimension tables.
The query works as desired, but my consistency check gives me the following WARNING:
*[39008] Logical dimension table LOCATION MASTER D has a source LOCATION MASTER D that does not join to any fact source.*
How do I resolve this WARNING, or at least suppress it?Hi,
What you need to do is to add the (physical) location dimension table to the logical table source of the demographic dimension, for example by dragging it from physical layer on top of logical table source of demographic logical dimension table in bmm layer
Regards,
Stijn -
[39008] Logical dimension table has a source that does not join to any fact
Dear reader,
After deleting a fact table from my physical layer and deleting it from my business model I'm getting an error: [39008] Logical dimension table TABLE X has a source TABLE X that does not join to any fact source. I do have an other fact table in the same physical model and in the same business model wich is joined to TABLE X both in the physical and business model.
I cannot figure out why I'm getting this error, even after deleting all joins and rebuilding the joins I'm getting this error. When I look into the "Joins Manager" these joins both in physical as well as logical model do exist, but with consistency check it warns me about [39008] blabla. When I ignore the warning and go to answers and try to show TABLE X (not fact, but dim) it gives me the following error.
Odbc driver returned an error (SQLExecDirectW).
Error Details
Error Codes: OPR4ONWY:U9IM8TAC:OI2DL65P
State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error has occurred. [nQSError: 14026] Unable to navigate requested expression: TABLE X.column X Please fix the metadata consistency warnings. (HY000)
SQL Issued: SELECT TABLE X.column X saw_0 FROM subject area ORDER BY saw_0
There is one *"special"* thing about this join. It is a complex join in the physical layer, because I need to do a between on dates and a smaller or equal than current date like this example dim.date between fact.date_begin and fact.date_end and dim.date <= current_date. In the business model I've got another complex join
Any help is kindly appreciated!Hi,
Have you specified the Content level of the Fact table and mapped it with the dimension in question? Ideally this should be done by default since one of the main features of the Oracle BI is its ability to determine which source to use and specifying content level is one of the main ways to achieve this.
Another quick thing that you might try is creating a dimension (hierarchy) in case it is not already present. I had a similar issue few days back and the warning was miraculously gone by doing this.
Regards -
3702i AP's not Joining WLC - Layer 3 discovery request not received on management VLAN
Hi Guys,
This is a follow up post to this thread: https://supportforums.cisco.com/discussion/12400481/3702i-not-joint-2504
Have been playing around with my AP's and made sure the time is correct on all the devices ( WLC and Switch). I have also moved the AP's to the same Vlan as the management IP of the WLC.
if I move the AP's to the same Vlan as the WLC they join and are happy, as soon as I move them to a different Vlan they cant join and there time goes back to the default plus they do not seem to save the WLC details to flash but still remember the test names I give them.
it appears that option 43 is working fine as I can see it look for the WLC IP and I have done some trouble shooting on the WLC and it looks like it see's the AP but doesn't except it.
please see below for the boot up of the AP and the WLC logs:
AP
IIOS Bootloader - Starting system.
*** deleted for breverity *****
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1"...#########################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Montserrat Board
*** deleted for breverity *****
Boot CMD: 'boot flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1;flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1'
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1"...###############################################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1" uncompressed and installed, entry point: 0x1003000
executing...
*** deleted for breverity *****
cisco AIR-CAP3702I-Z-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
Processor board ID FGL1838X4T1
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.0.110.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: F4:4E:05:B7:1E:84
Part Number : 73-15243-01
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC18343WPR
Top Assembly Part Number : 068-05054-03
Top Assembly Serial Number : FGL1838X4T1
Top Revision Number : A0
Product/Model Number : AIR-CAP3702I-Z-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:19.295: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar 1 00:00:19.755: Registering HW DTLS
*Mar 1 00:00:19.763: APAVC: Initial WLAN Buffers Given to System is 2500
*Mar 1 00:00:19.815: APAVC: WlanPAKs 42878 RadioPaks 42270
*Mar 1 00:00:22.127: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:26.055: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:26.167: Loading Power Tables from ram:/Q2.bin. Class = A
*Mar 1 00:00:26.167: record size of 3ss: 1168 read_ptr: 4F9698E
*Mar 1 00:00:31.207: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:31.251: Loading Power Tables from ram:/Q5.bin. Class = Z
*Mar 1 00:00:31.251: record size of vht: 2904 read_ptr: 4F9698E
*Mar 1 00:00:31.407: Wait until the stile protocol list is initialized.
*Mar 1 00:00:32.651: Start STILE Activation
*Mar 1 00:00:34.571: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:00:35.447: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 19-Dec-14 11:20 by prod_rel_team
*Mar 1 00:00:35.447: %SNMP-5-COLDSTART: SNMP agent on host Test_1 is undergoing a cold start
*Mar 1 00:00:36.563: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:37.787: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:37.939: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:37.939: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:47.567: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:48.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Mar 1 00:00:50.431: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
*Mar 1 00:00:50.431: DPAA Initialization Complete
*Mar 1 00:00:50.431: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:51.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:53.435: %LINK-6-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:00:53.867: Currently running a Release Image
*Mar 1 00:00:54.287: Incorrect certificate in SHA2 PB !
*Mar 1 00:00:54.287: Using SHA-1 signed certificate for image signing validation.
*Mar 1 00:00:54.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:59.787: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.2, mask 255.255.255.0, hostname Test_1
*Mar 1 00:01:02.707: APAVC: Succeeded to activate all the STILE protocols.
*Mar 1 00:01:02.707: APAVC: Registering with CFT
*Mar 1 00:01:02.707: APAVC: CFT registration of delete callback succeeded
*Mar 1 00:01:02.707: APAVC: Reattaching Original Buffer pool for system use
*Mar 1 00:01:02.707: Pool-ReAtach: paks 42878 radio42270
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:01:10.103: AP image integrity check PASSED
*Mar 1 00:01:10.187: Incorrect certificate in SHA2 PB !
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:01:11.591: %CDP_PD-4-POWER_OK: 15.4 W power - NEGOTIATED inline power source
*Mar 1 00:01:12.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.947: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:01:14.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:01:20.211: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:31.215: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
*Mar 1 00:02:11.599: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:02:11.603: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 1 00:02:11.611: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:02:12.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:02:12.639: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:02:12.647: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Mar 1 00:02:12.655: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:02:13.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:02:13.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:02:13.699: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:02:14.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
Not in Bound state.
*Mar 1 00:02:44.719: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:02:49.839: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.3, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:02:55.719: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
Not in Bound state.
*Mar 1 00:03:59.219: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:04:04.343: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.4, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:04:10.223: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
WLC:
isco Controller) >show time
Time............................................. Tue Jan 27 17:44:47 2015
Timezone delta................................... 0:0
Timezone location................................ (GMT +8:00) HongKong, Bejing, Chongquing
NTP Servers
NTP Polling Interval......................... 3600
Index NTP Key Index NTP Server NTP Msg Auth Status
1 0 150.101.176.226 AUTH DISABLED
(Cisco Controller) >show ap join stats summary
Incorrect input! Use 'show ap join stats summary [all/<ap-mac>]'
(Cisco Controller) >show ap join stats summary all
Number of APs.............................................. 2
Base Mac AP EthernetMac AP Name IP Address Status
f4:4e:05:aa:a6:a0 f4:4e:05:94:c3:98 APf44e.0594.c398 10.1.1.22 Joined
f4:4e:05:b6:ce:f0 N A Test_1 10.1.20.7 Not Joined
(Cisco Controller) >show ap join stats detailed f4:4e:05:b6:ce:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
Discovery phase statistics
- Discovery requests received.............................. 45
- Successful discovery responses sent...................... 21
- Unsuccessful discovery request processing................ 24
- Reason for last unsuccessful discovery attempt........... Layer 3 discovery request not received on management VLAN
- Time at last successful discovery attempt................ Jan 27 17:45:49.705
- Time at last unsuccessful discovery attempt.............. Jan 27 17:45:49.705
Join phase statistics
- Join requests received................................... 0
- Successful join responses sent........................... 0
- Unsuccessful join request processing..................... 0
- Reason for last unsuccessful join attempt................ Not applicable
- Time at last successful join attempt..................... Not applicable
- Time at last unsuccessful join attempt................... Not applicable
Configuration phase statistics
--More-- or (q)uit
- Configuration requests received.......................... 0
- Successful configuration responses sent.................. 0
- Unsuccessful configuration request processing............ 0
- Reason for last unsuccessful configuration attempt....... Not applicable
- Time at last successful configuration attempt............ Not applicable
- Time at last unsuccessful configuration attempt.......... Not applicable
Last AP message decryption failure details
- Reason for last message decryption failure............... Not applicable
Last AP disconnect details
- Reason for last AP connection failure.................... Not applicable
- Last AP disconnect reason................................ Not applicable
Last join error summary
- Type of error that occurred last......................... Lwapp discovery request rejected
- Reason for error that occurred last...................... Layer 3 discovery request not received on management VLAN
- Time at which the last join error occurred............... Jan 27 17:45:49.705
AP disconnect details
- Reason for last AP connection failure.................... Not applicable
Ethernet Mac : 00:00:00:00:00:00 Ip Address : 10.1.20.7
(Cisco Controller) >show interface summary
Number of Interfaces.......................... 4
Interface Name Port Vlan Id IP Address Type Ap Mgr Guest
ap LAG 20 10.1.20.231 Dynamic No No
guest LAG 30 10.1.30.231 Dynamic No No
management LAG 10 10.1.1.231 Static Yes No
virtual N/A N/A 1.1.1.1 Static No No
SWITCH
witch#show run
Building configuration...
*** deleted for breverity *****
no aaa new-model
clock timezone AWST 8
system mtu routing 1500
ip routing
ip dhcp pool WAP_Pool
network 10.1.20.0 255.255.255.0
default-router 10.1.20.1
option 43 hex f104.0a01.01e7
ip dhcp pool Clients
network 10.1.30.0 255.255.255.0
default-router 10.1.30.1
dns-server 203.0.178.191
ip dhcp pool test
network 10.1.1.0 255.255.255.0
default-router 10.1.1.1
crypto pki trustpoint TP-self-signed-4082587776
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-4082587776
revocation-check none
rsakeypair TP-self-signed-4082587776
*** deleted for breverity *****
*** deleted for breverity ***** !
interface FastEthernet0/3
description *** WLC ****
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/4
description **** AP *****
switchport access vlan 20
switchport mode access
spanning-tree portfast
interface FastEthernet0/5
description **** AP ****
switchport access vlan 20
switchport mode access
spanning-tree portfast
interface FastEthernet0/6
i*** deleted for breverity ***** !
interface Vlan10
description *** Managment ***
ip address 10.1.1.230 255.255.255.0
interface Vlan20
description *** WIRELESS APS ***
ip address 10.1.20.1 255.255.255.0
interface Vlan30
ip address 10.1.30.1 255.255.255.0
ip classless
ip route 0.0.0.0 0.0.0.0 10.1.1.1
ip http server
ip http secure-server
ip sla enable reaction-alerts
l*** deleted for breverity *****
ntp clock-period 36028827
ntp source FastEthernet0/1
ntp server 121.0.0.42
ntp server 202.127.210.37
end
I have also placed a Device in Vlan 20 and it is able to ping the WLC and the WLC can ping it s routing is working.
ThanksHey Scott,
I gave that a shot and still no luck, log's from AP boot up:
IIOS Bootloader - Starting system.
flash is writable
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 67 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 20894208
flashfs[0]: Bytes available: 20264448
flashfs[0]: flashfs fsck took 20 seconds.
Base Ethernet MAC address: f4:4e:05:b7:1e:84
Ethernet speed is 100 Mb - FULL Duplex
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1"...#########################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Montserrat Board
40MB format
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 67 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 20894208
flashfs[0]: Bytes available: 20264448
flashfs[0]: flashfs fsck took 21 seconds.
flashfs[1]: 0 files, 1 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 12257280
flashfs[1]: Bytes used: 1024
flashfs[1]: Bytes available: 12256256
flashfs[1]: flashfs fsck took 1 seconds.
Base Ethernet MAC address: f4:4e:05:b7:1e:84
Boot CMD: 'boot flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1;flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1'
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1"...###############################################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1" uncompressed and installed, entry point: 0x1003000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 19-Dec-14 11:20 by prod_rel_team
Montserrat Board
40MB format
Tide XL MB - 40MB of flash
Initializing flashfs...
flashfs[2]: 67 files, 9 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 40900608
flashfs[2]: Bytes used: 20894208
flashfs[2]: Bytes available: 20006400
flashfs[2]: flashfs fsck took 14 seconds.
flashfs[2]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 0 seconds.
flashfs[4]: Initialization complete.
Copying radio files from flash: to ram:
Copy in progress...CCCCC
Copy in progress...CCC
Copy in progress...CCCC
Copy in progress...CCCC
Copy in progress...CC
Copy in progress...CCCC
Copy in progress...CC
Copy in progress...CCCCC
Copy in progress...CCCC
Copy in progress...CC
Uncompressing radio files...
...done Initializing flashfs.
Radio0 present 8764 8000 0 A8000000 A8010000 0
Rate table has 650 entries (20 legacy/224 11n/406 11ac)
POWER TABLE FILENAME = ram:/Q2.bin
Radio1 present 8864 8000 0 80000000 80100000 4
POWER TABLE FILENAME = ram:/Q5.bin
Radio2 not present 0 0 0 0 0 8
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP3702I-Z-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
Processor board ID FGL1838X4T1
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.0.110.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: F4:4E:05:B7:1E:84
Part Number : 73-15243-01
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC18343WPR
Top Assembly Part Number : 068-05054-03
Top Assembly Serial Number : FGL1838X4T1
Top Revision Number : A0
Product/Model Number : AIR-CAP3702I-Z-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:19.295: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar 1 00:00:19.755: Registering HW DTLS
*Mar 1 00:00:19.763: APAVC: Initial WLAN Buffers Given to System is 2500
*Mar 1 00:00:19.815: APAVC: WlanPAKs 42878 RadioPaks 42270
*Mar 1 00:00:22.127: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:26.055: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:26.167: Loading Power Tables from ram:/Q2.bin. Class = A
*Mar 1 00:00:26.167: record size of 3ss: 1168 read_ptr: 4F9698E
*Mar 1 00:00:31.207: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:31.251: Loading Power Tables from ram:/Q5.bin. Class = Z
*Mar 1 00:00:31.251: record size of vht: 2904 read_ptr: 4F9698E
*Mar 1 00:00:31.407: Wait until the stile protocol list is initialized.
*Mar 1 00:00:32.651: Start STILE Activation
*Mar 1 00:00:34.571: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:00:35.447: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 19-Dec-14 11:20 by prod_rel_team
*Mar 1 00:00:35.447: %SNMP-5-COLDSTART: SNMP agent on host Test_1 is undergoing a cold start
*Mar 1 00:00:36.563: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:37.787: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:37.939: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:37.939: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:47.567: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:48.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Mar 1 00:00:50.431: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
*Mar 1 00:00:50.431: DPAA Initialization Complete
*Mar 1 00:00:50.431: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:51.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:53.435: %LINK-6-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:00:53.867: Currently running a Release Image
*Mar 1 00:00:54.287: Incorrect certificate in SHA2 PB !
*Mar 1 00:00:54.287: Using SHA-1 signed certificate for image signing validation.
*Mar 1 00:00:54.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:59.787: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.2, mask 255.255.255.0, hostname Test_1
*Mar 1 00:01:02.707: APAVC: Succeeded to activate all the STILE protocols.
*Mar 1 00:01:02.707: APAVC: Registering with CFT
*Mar 1 00:01:02.707: APAVC: CFT registration of delete callback succeeded
*Mar 1 00:01:02.707: APAVC: Reattaching Original Buffer pool for system use
*Mar 1 00:01:02.707: Pool-ReAtach: paks 42878 radio42270
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:01:10.103: AP image integrity check PASSED
*Mar 1 00:01:10.187: Incorrect certificate in SHA2 PB !
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:01:11.591: %CDP_PD-4-POWER_OK: 15.4 W power - NEGOTIATED inline power source
*Mar 1 00:01:12.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.947: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:01:14.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:01:20.211: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:31.215: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
*Mar 1 00:02:11.599: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:02:11.603: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 1 00:02:11.611: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:02:12.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:02:12.639: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:02:12.647: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Mar 1 00:02:12.655: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:02:13.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:02:13.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:02:13.699: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:02:14.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
Not in Bound state.
*Mar 1 00:02:44.719: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:02:49.839: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.3, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:02:55.719: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
Not in Bound state.
*Mar 1 00:03:59.219: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:04:04.343: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.4, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:04:10.223: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP -
How to have fact and dimension which are not joined in same report
Hi All,
suppose we have 2 dimensions and 1 of them is joined to fact but we want to pull both these dimensions along with fact and fact column shows null but we dont want that .how can we have 2nd dimension which is not joined to fact in the same report .Actually i have a column called equipment schedueled time and it can be shown only with equipment dimension but I want to pull both equipment,geography and equipment scheduled time in report if I do it now it shows equipment scheduled time as null because its not joined with geography dimension.I want even if the geography dimension exists it should show the value of equipment scheduled time .
Can someone please help me.
Thanks in AdvanceHi ,
Can you please tell me what are fact and dimension tables of your requirement.If you want display the data from 2 dims and a fact table ,you have to establish the joins between facts and dimensions.
mark if helpful/correct...
thanks,
prassu -
Oracle BI 11g
Hi,
I have this set of tables:
1) Table "Sales" with fields: ID, Billdate, ProductID, Amount
2) Table "Products" with fields: ID, ProductName, BrandID, TypeID
3) Table "Brands" with fields: ID, Name
4) Table "ProductTypes": ID, Name
In Physical layer I add these tables and create Physical Diagram with constraints like this:
[Brands] -------------------->[Products]
[ProductTypes] ---------->[Products]
[Products] -----------------> [Sales]
In Logical Layer I create logical table T1 Products with sources:
- LTS1 Brands,
- LTS2 ProductTypes,
- LTS3 Products
and fields:
- ProductID
- ProductName
- Brand
- ProductType
After that I create Dimention With Level-Based Hierarchy (H1 Products):
Total Products
- Brands
-- ProductTypes
--- Detail Products
When I try "Check Global Consistency" I get warning: "[39008] Logical dimension table T1 Products has a source LTS1 Brends that does not join to any fact source."
And after that when I try to make Analysis in Oracle BI, for example:
H1 Products | Amount
and then drill down item "Total Products" I receive error:
"State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error has occurred. [nQSError: 43113] Message returned from OBIS. [nQSError: 43119] Query Failed: [nQSError: 14025] No fact table exists at the requested level of detail: [,Brand,,,,,,,,,]. (HY000)"
What's wrong? Where do I mistake? And why I don't get any messages about Logical Table Source LTS2 Product Type?Hi,
you can create a single LTS for the product with the join for all 3 tables. Do you have a particular reason for the modelling that you have used?
Regards,
Gianluca -
Error 39008: logical table does not join to fact source
About to lose my mind over this error!
I'm told logical table IT_WORK_ITEM_D (a dimension) does not join to any fact source, although it should show as joined to IT_WORK_ITEM_DSNPSHT_F
- I have verified the physical joins
- I have verified the business model joins
- I have created hierarchies for all logical tables joined to the fact (IT_WORK_ITEM_DSNPSHT_F)
- I have checked the Content tab for the fact table and ensured that the logical dimension is set to the lowset level.
Suggestions from here?
-JohnThis was helpful, although it did not solve the problem immediately.
After much consistency checking, I cleared out some of the content assignments and that seemed to work (after having not worked). I still don't feel like I identified the core problem, but it is working now.
-John -
Hello all.
I have following situation.
I have a Employee table(w1_employee1_d1)
Salary table(w_salary_f) in Database.
every thing is fine when I import it in OBIEE Administration tool and use the answers.
Then I created a synonym as (w1_synonym_employee1_d1), believing that, synonyms can be used as tables/Views.
Now I imported into Physical layer and made a join in Start Schema in 'Physical Diagram'
and so far all is fine.
When I drag it in BMM layer and do a global consistency check, I get following error.
BUSINESS MODEL BIDATA:
[nQSError: 15001] Could not load navigation space for subject area BIDATA.
[15013] Logical table, BIDATA.W1_SYNONYM_EMPLOYEE1_D1, does not join to any other logical table
In BMM layer > right click the W1_SYNONYM_EMPLOYEE1_D1 > Bussiness Model Diagram > Whole Diagram
I can see the joins exists as how I made it in Physical layer.
what I am missing ? any help is appreciated.
ThanksOk Just for any body's information, My problem is partly resolved.
I added this in existing .RPD and it has caused the problems, which had Hirarchies and LTS and Alias tables.
However when I try a new and fresh .RPD and create a simple with synonym, that has not got this problem.
I will dig in the problems in old .RPD why there was error.
over all I must say the quest for this tests to find if I can use Synonym is been answered, using synonym in RPD is np at all.
Maybe you are looking for
-
Help! I want to move all my iTunes music, podcasts, etc. from an old PC to a new PC. I set up Home Sharing on both and it works. I followed the steps in http://support.apple.com/kb/HT4527 to the letter. At Step 11, I clicked on Home Sharing on my
-
Macintosh HD does not show up in Windows 7 bootcamp
I recently decided to transfer some things over to my hardrive, which is NTFS and needs to be used with Windows. This hasn't been a problem before now as i would just restart into Windows 7, plug in the harddrive, access the Macintosh HD from Windows
-
Install Enterprise performance management on DHCP
Hello all, Can I install Oracle Enterprise Performance Management on Linux DHCP computer ip address? How can I add an loopback netwotk ip loopback adress on this Linux system (a virtual machine on windows machine) as I can do on windows systems? I in
-
Hi everybody, I had OBIEE 11.1.1.7 deployed on Weblogic 10.3.6. Later I added ODI 11.1.7 to the same domain. I created a new server (odi_server1) which host ODI related deployments (odi_agent and odi_console). Today I noticed odi_server1 also hosts a
-
Why Windows 8 and Windows 8.1 (Even Windows 7) detects ip network address 169.254.201.217/16 on my computer??? I keep getting that most of the time.