Apple Care will not return my Hard drive.

I have a Power Book G4 1.67 . The hard drive has failed, it is covered under applecare for another 6 months, I have case number, the person on the phone was very nice, they sent the shipping box.
I think it's more then just the HD, however. The drive was partitioned in 3 sectors. Of course the system sector was the one that failed. I can boot in Target Disk Mode and see the other 2 sectors of the drive. The system sector is the one that is bad, I can't get that info off there. I am sure someone else can who is better qualified can. I really need that info, I can see they system partition in Disk Warrior, but am not a guru in that or the couple of other products I bought to see if I could rescue this info.
I asked AC Rep if I could have the Hard Drive back, they said no, I asked if they would back up the information, they said no, I said I would pay for either back up or pay for the old hard drive myself, (again) they said no.
So now I am stuck, if I replace that HD myself, I may void the warranty, I know it's a customer installable part. I have replaced many over my apple years, upgrading HDs about every 2 years in multiple computers and putting the old ones in external cases. I have also upgraded RAM, airport cards, pram batteries so I am comfortable working the simple upgrades. So I could simply replace that Hard Drive and then send it in, but then they may blame me for the problem.
There also smaller problems, screen latch won't stay closed, superdrive will not eject correctly, screen has some lines in it occasionally. It's not a road warrior, but I use it a lot and always treat these well. The drive was making no noise at all and no indication of a impeding failure. I treat my machines very carefully, I still have a Pismo that is gasping it's last breath.
This HD has all my important passwords and other personal info, I was in the middle of backing it up when thing went blitz. I saved the data from the other 2 partitions but I need that HD. Why will they not return my old part ? Or even back it up for a fee. I am afraid to replace the HD with a new one, and then send it off, or even try to reboot it from a new one as I maybe be stuck with it and they say well I did the damage.
Yes I know multiple back ups, but this is the first HD failure in 20 years and I should have had 2 HDs for back ups instead of one. Any other part I could see their point, but that HD has information I need and I don't want someone having it either. Is there a fair solution here.
This thing has been down a week, I just got the box and I need to do something. There is no Apple store up here and the company that can do the repairs, messed up a iBook G4, so the only option is sending it out to apple care.
Ideas and Suggestions?
Geoff

Well Holy Smoke !! Apple has agreed to let me get my data back a bit of a round about way but we will see.
I am going to use a hard drive recovery service so it will go like this.
A" local service provider," whom did not do anything at all to fix an iBook I gave them, under Apple Care to repair, but keep it 3 weeks and then said, I could not find anything by Goggling the problem...I see the problem that cursor is all over the place and jumps anywhere it wants., a problem came up and by the time we got back the iBook was out of warranty . Sometimes the local help is tough, but I try to support them.
I think, with me standing there, they can remove the hard drive from my powerbook, it's pretty easy..
Then, with Apple Care's blessing, I can send the drive into a recovery company, yes expensive, then return the drive in parts if that is the way it comes back, with my powerbook, ship it and AppleCare will fix it the PowerBook.
That is really good, and if all goes well, I will be very impressed and not hesitate to get that new
MBP. They even offered to let me take out the drive, but I thought, better to keep it in the "Apple Family."
Now they did not send a letter or email to this effect, that would have made me feel better, but the attitude at Apple, has really changed, these people went multiple times to supervisors to get this answer and solution. Not the quickest way to get it fixed, but
I am willing to bend, if they are willing to alter what is a well oiled line and will create a bump in their flow..
We will see, I told them they just might get a bag of parts and I will not reinstall the bad drive, as it is most definitely shot. No problem, it's all in the notes the CSR said.
We will see, but for today, this is sure a different attitude then the last go around, a few years ago. The CSR people are nice, understand English, as they seem to be based in Canada, which is a whole lot better then anywhere else I would want to talk too, or have talked to. They can understand abstract ideas, unlike those who just read from a card and stick to what the card says.
I am holding my breath, but I hope to report that this all goes smooth. I liked it when Apple was a good company. People went out of their way to help you no matter it took to get it fixed or working. I think a company can be good, profitable, plus have a excellent CSR and repair program.
For today at least, here is to Apple, way to go.
Geoff

Similar Messages

  • System Profiler will not recognize installed hard drive if drive is in use by VMWare

    System Information will not recognize installed Hard Drive (Boot Camp) when in use by VMWare.
    I work in IT for a School District and I am creating a Script that system information about the computer. I am testing this on a Mac Pro with two internal hard drives. One drive is Mac OS 10.8 and the other drive is a Boot Camp Drive that is used by VMWare Fusion.
    When I run System Information via the GUI or system_profiler via Terminal, both drives show up just fine. However, if I launch VMWare Fusion and run Windows from my Boot Camp drive, then run System Information via the GUI or system_profiler via Terminal, the Boot Camp Drive is no longer listed as an installed drive.
    Example:
    In the Terminal, I enter the following command.
    system_profiler SPStorageDataType
    Then it returns this information.
    Storage:
        Lion Client:
          Available: 217.84 GB (217,836,306,432 bytes)
          Capacity: 639.28 GB (639,275,270,144 bytes)
          Mount Point: /
          File System: Journaled HFS+
          Writable: Yes
          Ignore Ownership: No
          BSD Name: disk0s2
          Volume UUID: CCB501BF-AF24-30E7-A938-5A4E52DF14D7
          Physical Drive:
              Media Name: WDC WD6400AAKS-41H2B0 Media
              Medium Type: Rotational
              Protocol: SATA
              Internal: Yes
              Partition Map Type: GPT (GUID Partition Table)
              S.M.A.R.T. Status: Verified
        BOOTCAMP:
          Available: 255.58 GB (255,575,560,192 bytes)
          Capacity: 319.79 GB (319,790,510,080 bytes)
          Mount Point: /Volumes/BOOTCAMP
          File System: NTFS
          Writable: No
          Ignore Ownership: Yes
          BSD Name: disk1s2
          Volume UUID: D4B39D4E-E244-403C-AE4D-4D58397130DE
          Physical Drive:
              Media Name: WDC WD6400AAKS-41H2B0 Media
              Medium Type: Rotational
              Protocol: SATA
              Internal: Yes
              Partition Map Type: GPT (GUID Partition Table)
              S.M.A.R.T. Status: Verified
    Then I launch VMWare, which uses the Boot Camp drive. The once again run the same command from the Terminal Command and I get this.
    Storage:
        Lion Client:
          Available: 213.39 GB (213,392,244,736 bytes)
          Capacity: 639.28 GB (639,275,270,144 bytes)
          Mount Point: /
          File System: Journaled HFS+
          Writable: Yes
          Ignore Ownership: No
          BSD Name: disk0s2
          Volume UUID: CCB501BF-AF24-30E7-A938-5A4E52DF14D7
          Physical Drive:
              Media Name: WDC WD6400AAKS-41H2B0 Media
              Medium Type: Rotational
              Protocol: SATA
              Internal: Yes
              Partition Map Type: GPT (GUID Partition Table)
              S.M.A.R.T. Status: Verified
    The Boot Camp Drive is no longer listed.
    I assume this is due to the the fact that the drive is "In Use" however is seems odd since the Mac drive is also in use and it appears without problem. I assume there is no "fix" for this, I was just wondering if someone may have an explaination why?
    Also, I do realize that I can query the various interface types like system_profiler SPSerialATADataType to get all the properly installed phycial drives, but then I would have to query all possible interface types, isolate only devices containing Volumes, then consoldate the information to just the information that I need. I was hoping for a cleaner query.

    Thank you for your response.
    VMWare may be the cause, but the actual issue I am having is with Apple's System Information. I anticipated resistance from VMWare if I went to them with a question about an Apple software issue (even though VMWare software is part of the equation). I was trying to avoid the inevitable finger pointing game. I thought I would try with Apple Forums first since the issues presents itself within the Apple Software. However, you are correct that VMWare may have an explanation on why Fusion might be interfering with System Information. I will check with them next.
    To answer your question. Yes, In most cases I do use Fusion to run Windows side-by-side with the Mac OS. However, that is not always the case. There are a few reasons why I have it setup using a Dual Boot configuration.
    One, in some cases, due to the intense programs I occasionally run (graphic applications), I prefer to simply boot straight into Windows via Boot Camp so I may allocate all hardware resources to Windows. Additionally, some graphic applications like to have direct access to hardware and the extra layer of the VM environment can cause problems when an application is trying to directly access specific hardware like a graphics card.
    Second, I often use either side, both Mac and PC, for testing. There is an advantage to not having to rely on the Mac OS to run Windows. If, for whatever reason, my Mac becomes unstable due to testing, I can still jump right into Windows to do work if necessary.
    Third, I love the Mac OS, but I work in a PC centric organization. If there is a "problem" with my system, it is too easy for other system admins to say, "it's because it's a Mac". Having the definitive separation of the OS's allows me to prove that the Mac OS is not a factor.

  • I have iMovie 09. I just erased my external hard drive, but it is still formatted for the mac. However, iMovie will not recognize the hard drive. It shows the only hard drive available is the computers. How do I get the external hard drive to show up?

    I have iMovie 09. I just erased my external hard drive, but it is still formatted for the mac. However, iMovie will not recognize the hard drive. It shows the only hard drive available is the computers. How do I get the external hard drive to show up?

    In Finder's Menu, select Go menu>Go to Folder, and go to "/volumes". (no quotes)
    Volumes is where an alias to your hard drive ("/" at boot) is placed at startup, and where all the "mount points" for auxiliary drives are created for you to access them. This folder is normally hidden from view.
    Drives with an extra 1 on the end have a side-effect of mounting a drive with the same name as the system already think exists. Try trashing the duplicates with a 1 or 2 if there are no real files in them, and reboot.
    If it does contain data...
    http://support.apple.com/kb/TS2474

  • HP dv7 will not recognize second hard drive

    My HP dv7 2185dx running Windows 7 will not recognize second hard drive, bios recognizes it, Intel Rapid storage recognizes it.
    Primary hard drive is a 1TB, in install a second 500GB hard drive.
    This question was solved.
    View Solution.

    Hi,
    Hold down the Windows Key and press R.  Into the Run Box type compmgmt.msc and hit enter.  Click Disk Management in the left pane and let the drives load up. 
    Does the 2nd HDD show here?
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Imac will not see my hard drive on start up, wants to start from network start up disk that does not exist. How to get rid of it? So there is just one choice / my hard drive.

    I have a Intel duo Imac. Everything has been running relatively smoothly for a few years now. All of a sudden my computer will not start. I get the flashing folder with a question mark.
    When I go to Start up disk in my system perfernces while the computer is on. I see 2 possible choices. One is my hard drive with the operating system shown. The other is a non-existant Network Start up disk with a question mark in it ( looks like a hard drive with a question mark and it say's its a "network start up disk).
    All I think I want to do is get rid of the Network startup with the question mark. I can not find anywhere how one can just remove an old or non existant start up disk without reformatting.
    I believe this came from a clients hard drive who had a network system on it. We no longer have that drive. It no longer exists. But a latent icon shows up in start up disk.
    When I go to change the start up disk. I can change it to either the hard drive or the network with the question mark. But when I select my hard drive and then got to restart the computer. I get the flashing folder with a question mark on start up. I have also seen the flashing globe a couple times.
    When I attempt to run disk utility from may install disk ( holding down "C" on start-up ). Disk utility does not see my hard drive. Just the Apple install disk with the disk utility on it.
    What can I do to remedy this short of re-installing? Will a program like Disk Warrior or Tech Tool help?

    Thank you. That's what I thought will need to happen.
    One more question. I tried using the Apple install disk that came with the computer. It's an OS 10.5.6 disk. It does not see my 10.6.8 system internal hard drive to repair. All it see's is itself 10.5.6 disk. Do you think I can use a 10.8+ disk utillity since that is a higher system it will see the 10.6.8. Where the 10.5.6 does not?
    I don't want to turn the computer off for fear I'll get the question mark again. P-Ram got me going last time but for how long I don't know?  It would be nice to be able to turn the computer off for the night and startup as usual to give it a rest and try to reset itself.
    Thanks for your help, I know I will eventually need to re-install. But I am in the middle of a project with tight deadlines and all I can do right now is back-up. Trying to migrate to another computer temporarily to finish the job. That's a lot of extra work in the short time also.
    Just trying to put a band-aid on it for another couple weeks.

  • IMac 400dv will not recognize new hard drive installed

    Hi,
    I had been having trouble with my iMac 400dv's hard drive. I had posted the problems I was having and had gotten some very nice feedback. The final decision was to install a new hard drive and battery.
    I purchased a refurbished 40GB Maxtor to replace my old 20GB. Installation was no problem except that my iMac will not recognize the new drive. If I reinstall the old one, it recognizes it right away, so I know it has been installed correctly.
    I took the new hard drive back to the store and the tech said that it wasn't set on the "Master" position. He set it and tested the drive and said that it was fine. I reinstalled and get the same result, no drive can be sellected to install the software. No matter where I set the pin, I get the same result. I called the phone help line (MicroCenter) and the new tech told me that the drive was too big for my mac, which makes no sense to me since they suggested I buy a 100GB in the 1st place.
    I have 1GB of memory, my installation disk if for 8.6 and I will bring it up to 9.2 if I can get it running again.
    Any suggestions?
    thanks,
    Lucy

    Lucy Rust...
    In my opinion no Macintosh user should attempt to install a refurbished HD under any condition. Especially any HD that is to be bootable as they are no longer reliable for the Mac.
    Master setting is a must for the HD and never tinker with an optical setting. Well, if you could mess with the optical setting, expect to do some micro-surgery.
    You should be good for a HD up to a capacity of 120GB. The threshold is somewhere around 137GB but you will not find such odd capacity on the market.
    I think the rest has been covered.
    ...Ron

  • Will not recognize internal hard drive

    I have a strange problem with a 2009 MacBookPro.  It started acting "strange" for the user over the past few months.  By "strange" I mean it would freeze, or fail to boot, or sometimes even restart without any reason.  Now, it gets even stranger.  Tried the standard things,  RAM reseat, replace, check for loose connectors etc.  It would fail to boot when the hard drive was connected internally.  Then it would give a kernal panic and fail to even recognize a hard drive as being installed.  Did a PRam reset, SMC reset and even the power off/control key to try to reset the open firmware.  No sucess with anything.  This is a suystem with an internal battery.
    Yet, when using this exact same hard drive on an external USB drive connection, it would boot fine.  Next tried it in Terminal mode to boot up another MBP.  Failed to boot.  When the 2nd MBP was booted from its internal drive and the suspect machine was plugged in as a Firewire (Terminal mode on "strange" computer) an External Firewire Drive appeared on the desktop, then a few seconds later, an identical copy of the first Ext FW drive appeared.  This went on with evenbtually six copies of the one single Terminal booted hard drive appearing on the desktop of the second computer.  None of the six drives would open or even allow any indiccation of what they contained.
    Tried to partition the hard drive when it was put back into the internal slot but it would not unmount and failed to partition.  The same thinmg happened when trying to erase it.  Connected the hard drive via USB to a Windows 7 machine and used it to erase both the Recovery and Main partitions from the ard drive.  Both were erased but the EFI partition could not be erased or cleaned.  Put this same hard drive, as an external USB, into a very old XP machine and there the EFI partition was removed when a "Clean" command was sent via command line.
    I then took the, now totally erased hard drive, and put it back into the computer as an internal drive and booted the computer from a 10.8 USB stick so I could partition the now empty hard drive.  The drive was not even recognized as being present.  Did the same thing, but using the USB external connection for that same hard drive.  It partitioned and then formatted with 10.8.1 (what was on the USB stick).  After the OS was installed, the computer would boot using this newly created OS when connected as an external USB drive.  Put the drive back in as the internal drive.  Got a Kernal Panic.  Forced shutdown and retried.  Noi kernal Panic but drive was not even recognized.  Pulled the drive from internal and put it back into the external USB and tried booting.  System would not recognize the drive as even being present.
    I then erased and cleaned the drive in the XP machine again and then, using the USB connection on the second computer reinstalled 10.8 from the USB.  When I tried the now newly created software again, the same thing happened as listed above. 2nd machine booted fine on the drive as a USB, "Strange" machine booted fine using the drive as an external USB, Kernal Panicked then would not be recognized in the "Strange" machine.
    It appears that when the drive is connected internally. it not only does not have the OS software recognized but will rewrite something in the drive that makes it impossible to be recognized by any Apple.  My first thought was that the EFI partition was corrupted somehow so that was why I tried cleaning the EFI partition along with the other two partitions.  But even with a new EFI and other partitions, the drive was not useable once it was used to try to boot as an internal drive in the suspect computer.
    Now here I am dropping into speculation mode.  My guess is that something in the very basic ROM (Pram?) that recognizes a hard drive is in the internal slot and tries to get to the EFI instead fails and in the process it screws up the EFI (or maybe even an address table?) in the hard drive.  If it recognizes that there is no internal hard drive, it will happily boot from either a USB stick, a USB connected external hard drive or a Firewire/Terminal mode computer connected to it.
    Sounds like a motherboard problem but I am wondering if it is possible to "flash" the very basic ROM that is at the start of the process back to factory default or maybe just replace the chip if it is the same one used as part of the Firmware password protection system.
    Anyone have any other ideas or thoughts about possible solutions or at least a way to definitely identify what the problem's cause?

    Answer has been found.  The internal drive SATA cable was replaced and the system is now working correctly.

  • My Macbook Pro OS 10.7.5 will not recognize toshiba hard drive.  I will register on an iMac running the same OS.  Any ideas?

    I have a Toshiba external hard drive that i used with MacBook.  I now have a MacBook Pro running OS 10.7.5.  It does not register that the Toshiba hard drive is plugged in, yet if I plug it into an iMac running the same OS it does work.

    I don't know the answer to your problem, but until you resolve it do not upgrade OS X.
    I would suggest you try a reinstall:
    Reinstall Lion, Mountain Lion, or Mavericks without erasing drive
    Boot to the Recovery HD:
    Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Repair
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu.
    Reinstall Lion, Mountain Lion, or Mavericks
    OS X Mavericks- Reinstall OS X
    OS X Mountain Lion- Reinstall OS X
    OS X Lion- Reinstall Mac OS X
         Note: You will need an active Internet connection. I suggest using Ethernet
                     if possible because it is three times faster than wireless.

  • MacBook with Lion will not recognize external hard drive (AMP) that was my backup for older IBook, please help

    I had a IBook G4 and an external hard drive as its back up.
    IBook running something like Snow Lepord, anyway
    I have a Intel Macbook now with Lion, Ive been told here there is a possible confliction between the AMP external harddrive and lion.
    I will say a few times I have for limited time been able to access the drive on the newer MacBook, but then Lion (I think) drops it.
    Any ideas out there?

    Disk Utility sees the drive, finder/desktop doesnt.
    Click on the Desktop->Finder menu->Preferences->General->Show on Desktop->HDs and ext HDs.
    Mac OS Extended (journaled) what's that mean and is the format the issue here?
    http://support.apple.com/kb/HT1604 and http://support.apple.com/kb/HT2355
    No, that's not the issue.

  • Power Mac G4 400 MHz (AGP graphics) will not boot from hard drive

    I have a Mac G4 400 MHz (AGP graphics) Machine Model: PowerMac 3.1 CPU Type:PowerPC G4 (2.8)
    When I try to boot from the hard drive I get the folder with the flashing question Mark. The Machine will start up from the OSX 10.4 installer disk.
    The system was running OSX 10.4.9 fine. I began to have problems with the hard drive, so I replaced it with an old Maxtor 5T040H4 40Gig Apple branded drive that I had sitting around.
    The drive is jumpered (r50) for Master/Single.
    I erased the drive in the old G4 using disk utility and wrote all zeros. I then used my store bought Tiger 10.4 install disk to install 10.4 on the drive.
    After restarting I still get the flashing question mark. If I leave the Install disk in the DVD drive the system will attempt to install again.
    I have zapped the PRAM, pressed the CUDA button, removed the battery and let the system sit unplugged for over and hour and it still will not boot from the hard drive.
    To test the drive I removed it and put it in a Granite Digital firewire enclosure and connected it to another mac. The drive shows up and the system appears to be installed correctly.
    What am I forgetting to do? Does anyone have any suggestions.
    Thanks in advance.
    Wesley G.

    Hi! If Tom's solution doesn't work I would reboot from the install disc and then partition the drive as 1 partition instead of erasing it. Sounds like the driver on the disk is too old and installing a new partition map should write a new driver to the drive that is compatible with Tiger. Other than that it is possible that the drive has a spin delay jumper enabled and the drive isn't spinning up fast enough and the computer isn't looking long enough for the drive. Tom

  • After 10.5 upgrade Mac will not boot from hard drive

    I just upgraded to 10.5 Leopard but my mac will not boot from the hard drive even after selecting my hard drive as the startup disk. The mac will start to boot but will cut itself off before the boot is complete. I have to leave the Leopard disk in the mac and hold down C to get the mac to turn on but it only allows me to install the software again.

    instead of archive and install you might first want to try restoring your system using TM to some time point before your failed 10.5.1 upgrade. Then try upgrading to 10.5.1 again. I would suggest downloading the full 110 MB upgrade and installing it manually rather than doing it through the software upgrade menu.
    You can download the upgrade here:
    http://www.apple.com/downloads/macosx/apple/macosx_updates/macosx1051update.html

  • Purchased HD movie will not download to hard drive

    I have a windows vista laptop and windows xp desktop, both have latest iTunes, have have my library on an external mybooklive hard disk, I consolidated the library to the external drive with the vista machine, and pointed the XP machine to the library, when purchasing music i can download from the Cloud to the drive, I have purchased a HD 1080 movie using Apple TV, the movie plays on the Apple TV but this is streaming from the cloud I have tried to download the movie using the XP & Vista machines from the cloud to my hard drive, but it will not download, I get a dialogue box that says,( "This cannot be played in HD on this computer" "if you buy the HD version, you will have to transfer an HD-compatible device in order to watch it. Or, you can buy the SD version and watch it on this computer" ),
    I do not want to buy the SD version, I have already bought th HD version, I would like to store it on the external drive and stream to the Apple TV or my Ipad4, in the dialogue it says I can transfer to another device, only it will not download,
    can anybody please help with this? as I beleive I should be able to store it on the drive ready to play to those devices,
    if you need anymore info please respond,
    many thanks in advance,
    Tom

    Seriously, does no one know the answer to this? Do apple guys read these forums I have sent direct to apple too and no answer, please someone ,can you help
    Frustrated thank you

  • Mac will not boot from hard drive or install disc

    Hello All
    In dire need of advise...my intel Mac will not boot, even tried booting to the Snow Leopard install disc and all I'm getting is the white screen, apple logo and the wheel.
    Just before this happened there was a buzzing sound like the fan was about to fail but that is only a guess on my part. Is there a keyboard shortcut to boot to a terminal window or similar to force the computer to boot from the install disc.
    Thanks in advance for any help offered.
    Warren

    Hi Warren
    Try holding the Option key and see if it will boot into Startup Manager, where you should be able to choose from a good Drive or your install Disk.
    http://support.apple.com/kb/HT1533
    or the D key and run the Apple Hardware Test.
    http://support.apple.com/kb/HT1509
    Also note: key commands may require a USB Keyboard if your using a wireless and it has become unpaired.
    Dennis

  • Time machine will not recognise WD hard drive connected to AE

    I have a WD hard drive connected to my AE by ethernet cable. While I can access this drive wirelessly via Finder, both Airport utility and Time machine do not recognise this drive for back up purposes. Is there any way I can change the setup to enable time machine to work?
    Thanks - Eric

    You might want to take a look at the macosxhints.com article "10.5: Set up Time Machine on a NAS in three easy steps ".
    BTW, MobileMe won't be able to backup your entire hard drive.

  • Itunes Library will not copy to hard drive

    I can not Back up my iTunes library by copying to an external hard drive. The library is 300gb. It starts to copy very well and gets to 27.79 Gb and stops with an error message saying "Itunes already exists in this location." Which it does because that is the name of the file that I am moving and the computer itself has created a file called that to move the data into.
    Any ideas?

    P.S. An addition to the last post. Yes, my kids were in tears before it was finally loaded. If the cleaning does not work, call the tech support in the back of the Star Wars info booklet. There happened to be a smudge of glue of something from the factory on ours, that once removed, the Cd was fine. But we did not notice it until everything was about to be thrown out the window out of frustration.

Maybe you are looking for