Apple TV2 stopped working after upgrade...

I have a black ATV2 and after running an update back in May it killed it!
The upgrade process ran to the end but on trying to restart it failed and now the light on the front just flashes away as if to give me false hope but sadly no joy. I tried a soft reset by pressing the down and menu keys on the remote which it makes the light blink quicker but still it doesn't kickstart it into life. I then bought a micro USB cable and connected it to my iMac (no power cable) but still nothing. I'm not sure if I'm supposed to do anything with the remote at this point but I just can't get it to show up in iTunes and so I'm not able to perform the factory reset.
I feel I've exhausted all possibilities now and may have to take to my Apple store and see if they offer a replacement but I have had it for a couple of years. Can anyone suggest another method to revive this little box? I've feel a bit put out by this as it was Apple's update that has caused this, nothing I've done.
David

No guarantees but you might try the following:
    •    Launch iTunes
    •    Connect the Apple TV 2 to your computer
    •    Using the Apple TV aluminium remote, hold down both the Menu and Down buttons for about 6 seconds until the device reboots
    •    After reboot, release both of the buttons, and then immediately press and hold the Menu and Play button together
    •    Continue holding until you see a message in iTunes saying an Apple TV in recovery mode has been detected

Similar Messages

  • My Microsoft Office 2004 stopped working after upgrading to MT.  How can I get it to work, or, how can I uninstall MT?

    My Microsoft Office 2004 stopped working after upgrading to Mountain Lion.  How can I get it to work again, or, how can I uninstall MT?

    Office 2004 Applications Won't Work in Lion
    You must have Office 2004 which is a PPC-only suite and will not work in Lion. You need to upgrade to Office 2011 - Mactopia - or you can try the freeware suite, Libre Office, that is functionally similar to Office 2007 for Windows except it works on Lion.
    You may want to consider as well:
    These two suites are similar to Libre Office but not as current or as well-supported:
    NeoOffice
    Open Office
    And, then there is Apple's iWork suite:
    Pages - word processing and layout
    Keynote - presentation
    Numbers - spreadsheet
    Each can open and save Office compatible files. They may be purchased separately via the Mac App Store for $19.99 each.
    (Access to the Mac App Store requires Snow Leopard 10.6.6 or higher and an Apple ID.)

  • Why does the ipad 2 speaker stopped working after upgrading to ios 8

    WWhy does the iPad 2 speaker stopped working after upgrading to ios 8 why plz respond

    Hi A_S85,
    It appears your iPhone has an issue relating to sound. The following article may help you find a solution:
    If you hear no sound or distorted sound from your iPhone, iPad, or iPod touch speaker - Apple Support
    Can't hear anything from the built-in speaker of your iPhone, iPad, or iPod touch? Maybe you can hear, but the sound is distorted, muffled, intermittent. Or maybe you hear static or crackling noises. If your iOS device has any of these issues, follow these steps.
    Follow these steps and test the sound after each one.
    Go to Settings > Sounds and drag the Ringer And Alerts slider to turn the volume up.
    If you can hear sound from the speaker, then the speaker works. Continue with these steps to find the setting or switch that's affecting the sound. If you can't hear sound from the speaker, contact Apple Support.
    Make sure the Ring/Silent switch is set to ring. If you can see orange, it's set to silent.
    Restart your device.
    Open an app that has music or sound effects. Adjust the volume with the volume buttons or the slider in Control Center.
    Go to Settings > Bluetooth and turn off Bluetooth.
    If there's still no sound, connect a headset. If you can hear sound through the headset, remove it and clear any dust or debris from the headset jack of your device.
    If the device is in a case, make sure that the case doesn't block the speaker.
    Use a brush to gently clear any debris from the speaker and Lightning connector (or 30-pin dock connector). The brush should be clean and dry and have soft bristles.
    Update your device to the latest version of iOS.
    If you followed these steps and still hear no sound or distorted sound, contact Apple Support.
    Thank you for contributing to Apple Support Communities.
    Take care,
    Bobby_D

  • Kodak ESP 3200 stopped working after upgrading to Yosemite

    Kodak ESP 3200 stopped working after upgrading to Yosemite

    Kodak has posted an unsupported hack that has been reported to enable printing to a Kodak printer not supported in OS X 10.10 ("Yosemite"). Perhaps it would have the same effect with some other kinds of printers that aren't supported in Yosemite. I have no information about that, one way or the other.
    I have not tested the hack myself and I don't know all the possible effects. As far as I know it will not break the compatibility of printing software that is already compatible with Yosemite. It may degrade the security of the web administration interface of CUPS. That interface is not enabled by default, and will not be enabled by the procedure described here. Even if it were enabled, I know of no way it could be exploited, with or without the modification. Nevertheless, if you have enabled the web administration interface, you should disable it if you decide to follow these instructions. If you don't know what the web administration interface is, you haven't enabled it.

  • Macbook Pro optical drive stopped working after upgrading from Mac OS X 10.6 Snow Leopard to OS X Mavericks.

    My Macbook Pro optical drive stopped working after upgrading from Mac OS X 10.6 Snow Leopard to OS X Mavericks.. I wonder what's the work around or troubleshooting to fix this. Thanks!

    try and Reset the System Management Controller (SMC)

  • Windows media player stop working after upgraded from firefox 6.02 to Firefox 7.01 yesterday.

    windows media player stop working after upgraded from Firefox 6.02 to Firefox 7.01 yesterday.
    the plugin for win media player is already installed and working fine in FF 6.02 before upgrade. i have Google this issue without any result so far. so i reinstalled the old version 6.02, until fix is found.
    anyone has the similar issue with Firefox 7.01 in Win 7 32 bit ?

    The issue was not with FF 7.01. VLC player version 1.11.1 is conflicting with windows media player when FF 7.01 tries to play media files! Which was not happening before in FF 6.02.
    VLC and plugin media player need to be uninstalled first, then uninstalled FF 6.02. Install FF 7.01 and then win plugin media player again.
    Test media player at www.vdat.com/techsupport/windowstest.asp

  • My work e-mail stopped working after upgrading to 5 ios.

    My work e-mail stopped working after upgrading to 5 ios, I get the message that the mail server is not responding. Verify that you have entered the correct account info in mail settings. the information is correct and worked until I updated.

    That means you have to restore the device with iTunes now. So connect the iPad to your computer's iTunes and restore the iPad.
    iTunes: Restoring iOS software

  • After upgrading my iphone 4s software to 6.1.2, the sounds have stopped working, After upgrading my iphone 4s software to 6.1.2, the sounds have stopped working!

    After upgrading my iphone 4s software to 6.1.2, the sounds have stopped working, After upgrading my iphone 4s software to 6.1.2, the sounds have stopped working? Can it be recovered or a Hardware has to be replaced. I tried restoring my phone, but it did not work. Any solutions?

    alisportshots wrote:
    I have a similar problem, but after following your suggestion of deleting my iphone backup and then turning backup back on again, I needed to plug my phone into my computer to sync the backup.  I re-tried to do an icloud backup and it again told me that  "the last backup could not be completed"... since I had deleted the backup, it says the "Last backup:  never".  Ugh. I reconnected my iPhone 4S to my computer and iTunes so I could sync my phone and do a backup... it's still "waiting for sync to start"...
    For your iCloud backup, you may have an app that is preventing the backup from succeeding.  To locate which one, go to Settings>iCloud>Storage & Backup>Manage Storage, tap the name of your device under Backups, under Backup Options tap Show All Apps, then turn them all to Off (including camera roll) and try backing up again.  If it succeeds, then the camera roll and/or one of your apps is preventing the backup and you'll have to located by process of elimination. Turn the camera roll On and try backing up again.  If it succeeds, turn some of your apps to On and try backing up again.  If it succeeds again, turn some more apps to On then try again; repeat this process until it fails.  Eventually you'll be able to locate the problem app and exclude it from your backup.
    If you turned iCloud backup off and try to sync to create a backup on your computer and got a "waiting for sync to start" error, it may be caused by a corrupt backup on your computer.  You could try deleting your last backup by opeing iTunes and going to Preferences>Devices, clicking on your last backup and clicking Delete Backup.  Then try again.

  • Why does my cable selfie stick stop working after upgrading to iOS8.2?!

    I have an iPhone 6. My cable selfie stick stopped working after upgrading to iOS8.2.
    My friend's iPhone 6 is still iOS8.1, and the seflie stick works fine for him!
    How do I solve this?

    Are you using the paintbrush and have a gradient assigned to a stroke in CS6?
    Double click on paintbrush, and enable keep selected.
    If not give us a better explanation of what tool & settings you are using. (eg: blob brush, shape builder)

  • Location services is stopped working after upgrading to iOS 5

    Hi, Location services is not working after upgrading to iOS 5. How can i switch it on?

    Try resetting the iPod.  I had to do that to get my iPod to show via FindMyiPod.
    Reset iPod touch:  Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.

  • GCC Elite 21n+ Printer Stop working after Upgrade to Snow Leopard

    GCC Elite 21n+ B&W Laser Printer no longer works after upgrading to Snow Leopard 10.6.2.
    A back-up HP 2015DN Printer works intermittently. It will not work with ethernet cable connected to Net Gear Ethernet Hub (model FS105). But will work most of the time when ethernet cable is connected directly to back of computer.
    Back to GCC printer. Just cannot get it to work.
    But I cannot figure out what the IP address is for the GCC printer. Tried 192.168.1.4:9300
    See post (discussions.apple.com/thread.jspa?messageID=10127869). Still did not work.
    GCC tech have this work around. Here is what I received from GCC via email.
    +At 01/02/2010 12:21 AM we wrote -+
    +Since Apple has made the decision to eliminate Appletalk from it's Operating System, you are now forced to set the printer up over TCP/IP. Please keep in mind that GCC has never provided drivers for the Mac. We use the Apple Built in Print Driver. We do provide an OS X PPD Installer located on our website that I recommend you download, unstuff, install, reboot your Mac, then add the printer. You can find the Installer at http://www.gccprinters.com/support/doc/ Click on the Model of your printer and download the OS X Installer. DO NOT download the Applications Folder.+
    +You will need to set the printer up over TCP/IP, which means you will need to pull the IP Address of the printer from the Printers Configuration Page. Once you've done that, please do the following:+
    +You can add the printer over IP, that should work fine. Here are some steps for you to take.+
    +1) Select 'System Preferences...' (4th item) from the 'Apple' menu. The 'System Preference' panel will appear as a new window.+
    +2) Click on 'Print & Fax' icon (second row 'Hardware', second icon from right side). The 'System Preferences' panel will change into the 'Print & Fax' panel without opening a new window.+
    +3) Click on the '+' button to add a printer (2/3 the way down on the left side on the 'Print & Fax' panel). The 'Add Printer' dialog will open in a new window.+
    +4) Select the 'IP' icon in the top row of the 'Add Printer' dialog.+
    +5) Next to 'Protocol' select LPD Line Printer Daemon.+
    +6) Next to 'Address' type in the IP address you assigned to the printer. The Mac should prompt "complete and valid address".+
    +7) (Optionally) Next to 'Name' set the name of the printer to something friendlier. Normally it defaults to the IP address enter in the previous step. The 'Name' is what the printer is called in the print dialog.+
    +8) (Optionally) Next to 'Print Using' change/verify the PPD.+
    +9) Click 'Add' in the bottom right corner. After a few moments the 'Add Printer' dialog will close.+
    +10) The printer added in the previous step will appear in the list on the left side of the 'Print & Fax' panel. Click on the close box in the left-top of the 'Print & Fax' panel.+
    +11) Done. You should be ready to print.+
    Still cannot get the GCC printer to work or discover its IP address. Printer's Configuration page says
    TCP/IP: Enabled IP address: Unknown subnet Mask 255.255.255.0
    When I download the Drivers from GCC Web Site I only get a Text Document with loads of meaningless
    gibberish. There is nothing to unstuff and install.
    All worked well with OS 10.5.
    Thanks for shedding any light.
    John L.
    Thanks,
    John

    Hello John,
    At this stage you will not be able to get this to print until the printer has a valid IP address. According to your post, the IP address setting is enabled but the actual IP address is unknown. This is most likely a result of the GCC being set to DHCP but if there is no DHCP server or router capable of assigning the printer an IP address, then it will not get a valid address.
    So, the first thing I recommend is you check the documentation for manually setting an IP address into the printer. This address needs to be in the same subnet as your Mac. If you check System Preferences > Network on the Mac, you will see your IP address and subnet mask. If the subnet mask is set to 255.255.255.0, then you subnet will be the first three sets of numbers. For example, a device with an IP address of 192.168.1.12 and a subnet mask of 255.255.255.0 has a subnet of 19.2.168.1 and a network address of 12. Ideally, so that other devices can communicate with this device, they also need a subnet of 192.168.1 but a different network address, any number between 1 and 250 but one that is not already being used by another device, such as 12 in this example.
    Once you have the IP address set in the printer, then you add the printer as the GCC tech stated, using IP > LPD for the protocol. Note that you will only need to enter the IP address, such as 192.168.1.4 as per your post example. Don't enter any other numbers, such as the 9300 port reference you have tried already the colon after the IP address followed by the 9300).
    For the Print Using, you can use Generic PostScript to begin with as a test. If you then wanted to use the GCC PPD, then the link is okay. When you select the 21+n the next page shows the 21+ installer for OS 9 and OS X. This is a stuffit packed file so you will need some form of Stuffit (Stuffit Expander is a free download) to unpack the file first. Once unpacked, there is most likely an installer that you run. This will copy the PPD files for the printer to the appropriate folder.
    Hope this helps. Please reply if you require more help.
    Pahu

  • Keyboard shortcut command-w stopped working after upgrading to OSX 10.9.4

    Dear all,
    after upgrading to OSX 10.9.4 the keyboard shortcut command-w stops working after about 30 min of having the machine powered on. Interestingly, this phenomenon is not restricted to a certain app (Safari, etc.).
    In system preferences > keyboard all settings have been set to "default".
    Anybody else having the same issue?
    Many thanks,
    wolfgang

    Hi folks,
    just as quick documentation for possibly other error sources for the problem "shortcut command-w not working":
    If problem persists close all applications (allL!). Then open one app like Safari, open several tabs and check whether command-w works.
    Reason: it could happen that you've set command-w inadvertently in another app like Snagit. And when setting this the app did not tell you "listen dummy, this is a standard command, do you really want to replace a standard command with a app-specific command. Don't be surprised if it doesn't work when the app is running."
    This is what happened to me. So close all apps and check whether problem persists.
    reg,
    wolfgang

  • Wifi stopped working after upgrade, Asus N13

    Hi,
    A couple of days ago my wireless stopped working after I ran a full upgrade.  I have tried to identify the problem to no avail.  I attempted to use the Ralink drivers for my chipset rt3072 but those worked very poorly compared to the rt2800usb driver in the kernel and it kept freezing my system.
    My relevant lsusb entry:
    Bus 010 Device 005: ID 0b05:1784 ASUSTek Computer, Inc. USB-N13 802.11n Network Adapter (rev. A1) [Ralink RT3072]
    Output of lsmod | grep rt2
    rt2800usb 17360 0
    rt2x00usb 9026 1 rt2800usb
    rt2800lib 49258 1 rt2800usb
    rt2x00lib 35947 3 rt2x00usb,rt2800lib,rt2800usb
    mac80211 463233 3 rt2x00lib,rt2x00usb,rt2800lib
    cfg80211 430289 2 mac80211,rt2x00lib
    crc_ccitt 1363 1 rt2800lib
    usbcore 173007 11 uhci_hcd,snd_usb_audio,rt2x00usb,rt2800usb,snd_usbmidi_lib,ehci_hcd,ehci_pci,gspca_main,usbhid,gspca_zc3xx,xhci_hcd
    Output of dmesg | grep rt2
    [ 9.835141] usbcore: registered new interface driver rt2800usb
    Output of dmesg | tail after trying to connect:
    [ 3547.374615] wlan0: authenticate with 20:aa:4b:02:de:1b
    [ 3547.443545] wlan0: direct probe to 20:aa:4b:02:de:1b (try 1/3)
    [ 3547.643999] wlan0: direct probe to 20:aa:4b:02:de:1b (try 2/3)
    [ 3547.847118] wlan0: direct probe to 20:aa:4b:02:de:1b (try 3/3)
    [ 3548.050252] wlan0: authentication with 20:aa:4b:02:de:1b timed out
    [ 3554.041445] wlan0: authenticate with 20:aa:4b:02:de:1b
    [ 3554.110531] wlan0: direct probe to 20:aa:4b:02:de:1b (try 1/3)
    [ 3554.310824] wlan0: direct probe to 20:aa:4b:02:de:1b (try 2/3)
    [ 3554.513940] wlan0: direct probe to 20:aa:4b:02:de:1b (try 3/3)
    [ 3554.717073] wlan0: authentication with 20:aa:4b:02:de:1b timed out
    I am using wicd but I have also tried with NetworkManager (I have made sure to systemctl disable the one not under test).
    I tried using wireshark in monitor mode on another computer to capture the exchange for authentication.  I can see my computer request authentication and I can see the router reply back.  The reply is an authentication successful message, but then my computer immediately tries to authenticate again.
    Any help would be appreciated.

    glittercutter wrote:
    Hi,
    I have the same device and a similar issue.
    Connection works but pinging the router shows extremely high ping (over 3000ms) and high packet loss, especially when the network is under load.
    The connection drop randomly and wont reconnect until I manualy unplug and replug the usb device.
    Downgrading the kernel fixed the problem.
    Which kernel version did you downgrade to?
    I also have the same device at home and I might face the same problem when I go back home next month.
    Last edited by ico (2013-04-27 18:30:07)

  • TS2972 Home Sharing with ATV stopped working after upgrade to iTunes 11

    After upgrading to iTunes 11, my two PCs are no longer visible to Apple TV or the iOS Remote App.  I went through all the steps in "Troubleshooting Home Sharing" http://support.apple.com/kb/TS2972 without success.  In additions, I tried:
    Turning Home Sharing off, then on again on both PCs
    Re-created Firewall rules for iTunes
    Ran a factory reset on Apple TV
    Disabled iPV6 on the network adapter, based on a blogger's fix for an iTunes 10 problem
    Some other observations:
    Home Sharing was working with Apple TV an hour before I ran the updates for iTunes 11 and Apple TV. 
    The Apple TV and iOS Remote App are working together, so the network settings must be correct.
    The PCs in question are running Window 8 Pro 64-bit and Windows 7 Pro 64-bit
    The two PCs can see eachother's iTunes.
    It seems likely this is an iTunes 11 issue, but upgrading ATV2 at the same time clouds the diagnostics.
    I was just about to order two more Apple TVs, but now have second thoughts now that my ATV2 is just a doorstop. 
    Any suggestions? 

    You are not alone with issues related to the e1000e (but all they concluded was that reloading the module makes it work again):
    https://bbs.archlinux.org/viewtopic.php?id=145564
    It seems like this is more your issue:
    http://permalink.gmane.org/gmane.linux. … devel/8932
    But if none of those boot flags work for you, then there's not much you can do, and you'll have to write a script to reload the module each time after initial boot finishes I guess until the module gets fixed.
    Also, power management of the PCIe interface causes the e1000e to shut off after a while as well (lots of people on CentOS noticing this):
    http://serverfault.com/questions/226319 … ie-aspm-do
    So you can use that boot parameter to stop that from happening, if that becomes an issue for you as well.

  • Cinema display USB stops working after upgrading to mountain lion

    I am using a newly bought 27' Cinema display + mid 2011 MBA. an Apple USB keyboard is attached to the display USB port, and a logitech mouse is attached to the USB port on the keyboard.
    After upgrading to mountain lion, when I unplug the thunderbolt from MBA, and then plug it back, the USB keyboard and mouse stops working. Moreover, I cannot open anything in System preference, and cannot properly shutdown the machine!
    Please help on this issue.

    Launch Terminal, type or copy/paste the following:
    killall Dock
    Hit enter.

Maybe you are looking for

  • Itunes 6 will not open in windows xp professional

    I upgraded to itunes 6 on a Dell Latitide X300 with Windows XP Professional. I have Symantec Client Virus. I do not see itunes in the Processes tab. I have the latest windows service pack installed. I already disabled the firewall on the Windows Secu

  • Unable to create a Line chart

    Hi Friends, I am trying to create a Line Chart based on CalMonth, where I want to show no. of SalesOrg denoted by different lines separately according to their monthly sales. Please help. Regards, Jatin

  • Moving photo storage medium

    I store all of my photos on an external drive which is connected to a windows pc.  They have been linked into iPhoto but without copying the original photo itself.  I now need to move the external hard drive and connect it diirectly to my imac, but i

  • Windows 7 starter on macbook pro

    Can I install windws 7 starter on macbook pro 2011 (MC700 )with bootcamp??? Message was edited by: BrunoMattos

  • Complex model-driven filters

    Hello, I'm working on an application using the model-driven LCDS tools. The initial proof of concept has been fairly successful but I'm running into problems trying to customise the java assemblers which are generated from the model. For certain enti