AS5300 with IDSN PRI for VoIP and 56K dialup

Hello everyone, I'm faced with a configuration issue on an existing AS5300 server
[IOS (tm) 5300 Software (C5300-JS-M), Version 12.3(15)]
24 Serial network interface(s)
60 terminal line(s)
4 Channelized T1/PRI port(s)
30 DSP(s), 30 Voice resource(s)
I have been able to route any voice calls to SBC's via session targets and dialp-peers although I cannot make 56K dialup calls to async ports. Modems are all running:
Modem module Firmware Boot DSP
Mdm Number Rev Rev Rev
1/0 0 2.9.5.0
and modem tests show all are functioning. I can make outbound calls using isdn test calls to any number, so I know two 2way PRI is working correctly on that regard.
Is there anything else that I can look at or do I have some mistakes in my config:
controller T1 0
framing esf
clock source line primary
linecode b8zs
pri-group timeslots 1-24
interface Serial0:23
ip unnumbered Ethernet0
encapsulation ppp
dialer-group 1
isdn switch-type primary-ni
isdn incoming-voice modem
peer default ip address pool setup_pool
ppp authentication chap pap
interface Group-Async1
ip unnumbered FastEthernet0
encapsulation ppp
ip tcp header-compression
timeout absolute 1440 0
async mode interactive
peer default ip address pool setup_pool
ppp authentication pap callin
group-range 1 60
line 1 60
login local
modem InOut
modem autoconfigure discovery
modem dialout controller 0
transport input all
autoselect during-login
autoselect ppp
I have tried many diffenent combinations of the above but can somebody suggest anything else?
thanks
some extra info
AS5300#show modem map
Slot 1 has Mica Carrier card.
Modem Firmware Firmware
Module Numbers Rev Filename
0 1/0 - 1/5 2.9.5.0 IOS-Default
1 1/6 - 1/11 2.9.5.0 IOS-Default
2 1/12 - 1/17 2.9.5.0 IOS-Default
3 1/18 - 1/23 2.9.5.0 IOS-Default
4 1/24 - 1/29 2.9.5.0 IOS-Default
5 1/30 - 1/35 2.9.5.0 flash:mica-modem-pw.2.9.5.0.bin
6 1/36 - 1/41 2.9.5.0 flash:mica-modem-pw.2.9.5.0.bin
7 1/42 - 1/47 2.9.5.0 flash:mica-modem-pw.2.9.5.0.bin
8 1/48 - 1/53 2.9.5.0 flash:mica-modem-pw.2.9.5.0.bin
9 1/54 - 1/59 2.9.5.0 flash:mica-modem-pw.2.9.5.0.bin
Firmware-file Version Firmware-Type
============= ======= =============
system:/ucode/mica_board_firmware 3.0.4.1 Mica Boardware
system:/ucode/mica_port_firmware 2.9.5.0 Mica Portware
system:/ucode/microcom_firmware 5.2.30 Microcom F/W and DSP
flash:mica-modem-pw.2.9.5.0.bin 2.9.5.0 Mica Portware
AS5300#

Thanks for the info, however going backwards I am not able to configure the AS5300 as a dedicated Dial-up access server for ISP customers to dial-up to 56K
Perhaps the modem software is out of date on my router?

Similar Messages

Why isn't there yet an available p2p embeded code for voip and video conference in Firefox??

why isn't there yet an available p2p embeded code for voip and video conference in Firefox??

So, the upload time will vary on internet connection. If there is an issue with how fast it is uploaded you can check if prefetching is turned on, but this does not really affect uploading [https://developer.mozilla.org/en-US/docs/Controlling_DNS_prefetching Controlling DNS prefetching]
If you search for solutions, you will see a bunch of tweaks as well that may be helpful to your specific computer. [[Upgrade your graphics drivers to use hardware acceleration and WebGL]] to make sure you are all up to date as well.

I have 2 macbooks each with an account for me and one for my wife. I use one Macbook logged in with my account and my wife uses the other Macbook only loged in on her account. We both make regular time-machine back-ups each on a separate external disk

I have 2 Macbooks each with an account for me and one for my wife. I use one Macbook logged in with my account and my wife uses the other Macbook only logged in on her account. We both make regular time-machine back-ups each on a separate external disk. Is it possible to update her account on my macbook using her external disk without overwriting my stuff on the same Macbook and vice versa?

Time Machine does not do individual accounts. It records the complete drive. So if you were to use her TM backup on your Mac it would make your Mac just like hers. Both yours and her account on your MAC.
Just copy the missing files over from her Mac to yours. If there are differennt programs on each then they would need to be installed on both.

Ihave downloaded iCloud to my new PC and am using windows 7 and office 2010. I cannot get iCloud to come up on Outlook with the choices for CalendCar and contacrts, my iMail account is there, but not the general coud choices. What am I doing wrong.

I have downloaded iCloud to my new PC and am using Windows 7 and Offie 2010. I cannot get iCloud to come up on Outlook with the choices for Calendar and Contacts, my iMail accnt is there***.me.com, but not the general Cloud choices for calendar and contacts? What am I doing wrong?

I have I cloud 2.0.2.187 loaded just downloaded yesterday.

I have the new macbook pro with retina and I am trying to back up with wd passport for mac and is telling me it is going to take 7days

I have the new macbook pro with retina and I am trying to back it up, with wd passport for mac and is telling me it is going to take 7days. Any Ideas? Im afraid that means there is something wrong with my hard drive. I have verified the disk and it says everthing is ok.

It seems to be a common problem that those drives don't perform well, at least not with Time Machine.
If you have more than one user account, these instructions must be carried out as an administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left.
Enter the word "Starting" (without the quotes) in the String Matching text field. You should now see log messages with the words "Starting * backup," where * represents any of the words "automatic," "manual," or "standard." Note the timestamp of the last such message. Clear the text field and scroll back in the log to that time. Post the messages timestamped from then until the end of the backup, or the end of the log if that's not clear.
Post the log text, please, not a screenshot. If there are runs of repeated messages, post only one example of each. Don't post many repetitions of the same message.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into a message.
Some personal information, such as the names of your files, may be included — edit that out, too, but don’t remove the context.

I have a Honday FIT 2013 with the USB for iPod and the Auxillary jack. I plan to purchase an iPhone 5c. Can I listen to music from my iPhone through my car speakers?

I have a Honday FIT 2013 with the USB for iPod and the Auxillary jack. I plan to purchase an iPhone 5c. Can I listen to music from my iPhone through my car speakers?

Click the "Upgrade Eligibility" link on the right side (under "Learn more about buying iPhone) here:
http://store.apple.com/us/buy-iphone/iphone5s
If you're not eligible for upgrade, it will tell you how much more than US$199 you will be charged.

With my friend for trolling, and I decided I wanted it out of my life, but forgot the password and used a fake email! I have no

How do I stop getting notifications from the wrong instagram account on my iPhone?
Okay. So, I made a second instagram account with my friend for trolling, and I decided I wanted it out of my life, but forgot the password and used a fake email! I have no way of logging on or deleting the account, so I figured I would just forget about it. But after I logged back on to my regular one, I kept getting notifications from the fake account!! I don't know what to do because there are some vulgar things that keep popping up and I just want them gone! :'( Can anyone help??

see this support article about A flashing question mark appears when you start your Mac

Issue with Visibility Settings for Backgrounds and Layers

I am using Acrobat Pro XI 11.0.10 (Windows) and having an issue with visibility settings for layers and backgrounds. I am attempting to get backgrounds to appear while viewing in Adobe Reader and Acrobat Pro but not be printed and so far have had no success.
When using a background the Appearance Options dialogue has "Show when printing" unchecked, but "Show when displaying on screen" is checked. This results in the background not showing on the screen, and the background will only appear once the box for "Show when printing" is checked. It looks like the option for printing is dictating whether or not the background is able to appear.
Using layers has not worked either. The background layer is set to "Never Prints", but will still show up when printed.
I was wondering if anyone else has run into this and has a solution, or has any recommendations.
Thanks in advance.

Hi setrev2012,
How are you adding the backgroud?
The only way I can think to accomplish this is via a watermark.
The basics...
Open PDF in Acrobat. Choose Pages > Watermark > Add Watermark.
Select a jpg or PDF of your background and adjust scaling options as desired.
Then click the Appearance Options.. and uncheck the Show When Printing option.
In this image the PDF is a blank page with the word "Test" on it. The watermark is the stamp and impression (a stock photo jpg).
If you want a solid color background, just create a flat image of the background color for use as the watermark.
If you have already followed the steps and still facing the issue then please share the file with me at [email protected] so that i can have a look.
Regards,
Rave

HT2477 Are documentS created with Microsoft office for windows and Microsoft office for mac are compatible with each other

Are documents created with Microsoft office for windows and Microsoft office for mac are compatible with each other?

As with a lot of software, it depends on the version of Word, and what features the author used.
Technically, Office 2010 for Windows and 2011 for Mac are supposed to be feature compatible. As are Office 2007 for Windows, and 2008 for Mac.
However, if a person using Office 2010 / 2011 used a feature that only exists in that version and sends the file to someone using Office 2007 / 2008, they would very likely have trouble opening the file, or having it display as intended.

I still have a warranty but it will be out in a week. i previously have a sound distortion problem with my mac for months and suddenly it just fix itself. what should i do? i'm worried that it will comeback and i dont have a warranty anymore.

i still have a warranty but it will be out in a week. i previously have a sound distortion problem with my mac for months and suddenly it just fix itself. what should i do? i'm worried that it will comeback and i dont have a warranty anymore.

JoBautista,
you still have the option (before your warranty expires) of purchasing an AppleCare Protection Plan, which will provide an additional two years of coverage. Once your warranty expires, you will no longer have the option of purchasing AppleCare.

Port with multi-vlan for voice and data??

Hi guys,
I've a situation where my VOIP and DATA on a different segments. Voice is 10.x.x.x riding on VLAN 701. And my data is 192.x.x.x riding on VLAN 100.
The problem occur when our receptionist PC have a software installed for call forwarding for our general line. This software need to be on the same vlan with the IP Phone vlan which is 701. If I put her PC on those vlan, she can't access
to our LAN which is vlan 100. So she can't check her email etc.
Can I know what is the options I have? Can I configured multi-vlan for her PC on the switch? We are using Cisco PoE 3560 switch. Thanks.

Hi,
on the L3 switch, you should have an IP address for both VLAN 701 and 100. So, the L3 switch is doing inter-VLAN routing.
This means, unless you have ACL blocking traffic, any device will be able to reach any other device, even on a different VLAN.
And, no matter where you put voice and applications, everything will work anyway.

Setting up two iPod Touches on one account with gift cards for app and in-app purchases

I have multiple devices on one account - 2 iPod classics, one iPhone 3G and two recently acquired iPod Touches for my 8 year old boys. They want to make in-app purchases (for Dragonville). They each have their own gamecenter ID. I want to set up each of them with gift cards for their purchases. Is this possible?
If not, what is the recommended approach to manage all devices in one place while allowing individual devices to have a seperate payment mechanism?
Thanks.

I recommend that you
Create a NEW account/ID for her using these instructions. Make sure you follow the instructions. Many do not and if you do not you will not get the None option. You must use an email address that you have not used with Apple before. Make sure you specify a birthdate that results in being at least 13 years old
Creating an iTunes Store, App Store, iBookstore, and Mac App Store account without a credit card
More details of how:
http://ipadhelp.com/ipad-help-tips-tricks/how-to-get-free-apps-from-the-app-stor e-without-a-credit-card/
Use the new ID on her iPod but only for:
Settings>Messages>Send and Receive
Settings>FaceTime
Settings>GameCenter
and Settings>iCloud if you want her to have separate Contacts Calendar and some other things.
Continue to use the same/common Apple ID for Settings>iTunes and App stores so you can share purchases.
To make sure you only sync the media yoo want, configure iTunes syncing so that only checked media is synced to the idevices.
iTunes: Syncing media content to iOS devices and iPod
Also see:
How to use multiple iPods, iPads, or iPhones with one computer

What's the deal with 7:22 For iCal and iPhoto

Ok, so I'm having this problem where on every single saved picture or document the "Get Info" tab shows it as being created at either 7:22 AM or 7:22 PM. Also, all of my events on iCal show up automatically as happening at 7:22 when I select the "Show Time in Month View" option under Preferences. Any ideas?..

Sure. Once you open Terminal, you will be presented with a shell prompt. The "shell" is what's running inside the terminal, and is what processes the commands you type in. Common shells are sh, bash, zsh, csh, tcsh. You are probably running bash by default. For you, it really doesn't matter what shell you are running.
Your prompt will probably look similar to this:
<machine name>:~ <username>$
where <machine name> is the name of your machine, and <username> is the name you logged into your system with. So for me, this looks like:
tomservo:~ glsmith$
So, at this prompt, I wanted you to type:
cp gradparty.jpeg ~/Desktop/testpic.jpeg
The "cp" is a program that copies files. That invocation says "copy file gradparty.jpeg to a new location located in the user's home folder, in the sub-folder called Desktop, and rename it to testpic.jpeg". Note that I used a shortcut -- in Unix, the "~" stands for the home directory (aka folder) of the user issuing the command. It's a quick way to get rooted to your home folder without having to type the full path.
Another thing to note is that the above command assumes that you are in the folder that contains the file "gradparty.jpeg". To get there from the Terminal, you will have to use the "cd" command. For example, let's say I have this image in a sub-folder called Graduation inside my Pictures folder. From the Terminal, I could get there by typing:
tomservo:~ glsmith$ cd Pictures/Graduation
and I could verify that the image is there by then typing:
tomservo:~ glsmith$ ls -l gradparty.jpeg
"ls" is what lists files in a directory (similar to "dir" in Windows).
So, once you've done the copy, you will have a new file sitting on your Desktop. This is what I want you to look at in the Finder to see if the times are still messed up.

Setting mail with Cox (or other services with different servers for pop and smtp)

My Cox mail account uses different servers for pop and smtp (my personal ISP 1&1 does too).
The mail applet on my Blackberry Curve 8330 with Verizon does not allow to define different servers for pop and smtp, and further, for SSL smtp mail, the port is fixed at 995 and cannot be changed, while Cox (and 1&1) want to use 587 or something like that.
As a result, I can only receive mail with these services.
I also have yahoo mail, which works fine, so I can send mail with it and it is not a life-and-death situation, but I would like to be able to just reply to email sent to my Cox address.
I called Verizon and they said BlackBerry provides the mail access through their servers and the applet, so there is nothing they can do.
Is there a way to set it such that I can not only receive but also send mail through either of these services?
Thanks in advance,
Didier
PS: Other than that, the Curve on Verizon rocks!!! so much better down here than AT&T it's not even funny.

OK, thank you for the input.
The problem I have with this solution is like the one I have now using yahoo.
There are 2 problems:
1) mailing lists want the mail to come from the account that is subscribed, so if the cox account is subscribed, I can't contribute from the blackberry, and if the blackberry account is subscribed, I don't get my mail in Outlook. Neither is good for me.
2) people who send me mail to the Cox account and get replies from me from the blackberry continue responding to the account that can send from the blackberry (not Cox), and from that point on I do not have that mail on the computer.
The issue of having two copies is no big deal, I just delete the mail I do not need. I would rather have two than none.
Really, Blackberry should modify the email service so that they directly support mail systems like those of Cox and 1&1. I am sure there are others. They should also allow the use of another port for SSL than 995. I have not seen anyone using 995 for SSL.
Until recently, I had a BB provided by my employer, and we had a BES, and that worked really well. I would like to emulate as much of that functionality as possible without having to pay somebody another $10 or $20 a month just for the priviledge of having an account on a private BES server.
Anyway, thanks for the exchange and suggestions.
Didier

Problem with iWeb asking for username and password to access my public site

Today for some reason anyone trying to access my site is being asked for username and password. I have made no changes that would require a password. My site has always been public.

I am having the same problems. My site is public, I checked the settings on the public folder on MobileMe to ensure that it was public and did not require password protection either. But for some odd reason, even though I didn't change anything, my site's pages seem to require a user name and password to get into them. If one continues to click cancel, the page continues to load.
This does not happen every single time, but it happens more often than not. I have tried this with my iMac, Macbook, as well as my iPod Touch, and I get this on all machines. My brother has tried logging in from another location using his Macbook Pro, and he gets the password prompt as well.
I tried turning on password protection to the site and uploading the changes, then disabling password protection and reupping the changes once again. I've tried uploading entire site, instead of just changes, but the problem continues to persist. I definitely need this issue solved since this site is important to me.
The site url is: http://www.globalwinetour.com
Does anyone have any suggestions to rectify this, or does anyone have any idea what is causing it? Am I missing something here? Am I doing something wrong? Please help me out!
Many thanks in advance!

AS5300 with IDSN PRI for VoIP and 56K dialup

Similar Messages

Maybe you are looking for