Asa 5505, the outside cant access to a server in the inside

hi, i have an Asa 5505, a pc in the outside with the ip 10.1.1.6 cant access to a server in the inside 192.168.1.4, pls help...
this is my conf:
ASA Version 8.0(4)
hostname ciscoasa
domain-name default.domain.invalid
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif inside
security-level 0
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 10.1.1.2 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa804-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
access-list 100 extended permit tcp any host 10.1.1.3 eq www
pager lines 24
logging enable
logging asdm debugging
mtu inside 1500
<--- More --->
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-613.bin
no asdm history enable
arp timeout 14400
nat-control
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) 10.1.1.3 192.168.1.4 netmask 255.255.255.255
access-group 100 in interface outside
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
<--- More --->
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
dhcpd address 192.168.1.2-192.168.1.254 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
<--- More --->
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:14e7b74fabc386613ae646b915f60e9e
: end
ciscoasa#

Andres
The security level for your inside interface should be 100 ie.
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
After changing that can you
1) ping the outside interface of the ASA from the pc or ping the PC from the ASA
2) I'm assuming you are trying to connect to 10.1.1.3 when you attempt the connection ?
Jon

Similar Messages

ASA 5505 switch from Mode: access Port to Trunk on the fly via CSM ?

Hi
Can I configure the Port at the ASA 5050 from Mode: access Port to trunk during the FW is running in a production area without console access ?
As I know at the 5505 ist should work
sincerley
Alfred

Are you using the same access port to access the ASA via CSM? If you are, then i would strongly recommend console access.
If you are using a different port to make the changes, then yes you can configure it. However, I would still recommend configuring it during non production hour, just in case there is an issue.

Sound on my phone has gone so when someone calls me they can hear me but i cant hear them.The ticks cant be heard when you press the keyboard. I've checked the settings and they are ok. can still hear music thru headphones but not without. Any help pls.

sound on my phone has gone so when someone calls me they can hear me but i cant hear them.The ticks cant be heard when you press the keyboard. I've checked the settings and they are ok. can still hear music thru headphones but not without. Any help pls.

Hey shahbazfromgbr,
Thanks for the question, and welcome to Apple Support Communities.
I understand you are having issues with sound output on your iPhone 4S. For troubleshooting steps, the following article provides the best information:
iPhone: Can't hear through the receiver or speakers
http://support.apple.com/kb/TS1630
1. Verify that there is nothing plugged in to the headset jack, including headsets, headphones, or adapters.
2. Make sure the Ring/Silent switch is not switched to silent.
3. While on the Home screen, adjust the volume buttons. If you see the icon below, indicating that headphones are attached, there may be debris or an object lodged in the headset jack:
4. Check the headset jack. If there is an object lodged in the headset jack that is not easily removed, have the iPhone serviced to remove object.
5. For Original iPhone: If there is light debris, such as lint, in the headset jack, try connecting a pair of headphones to the headset jack and then remove the headphones. Repeat this several times to remove the debris.
6. If you have installed a protective film on the display, either ensure that the receiver is not covered or remove the film completely.
7. Check the receiver mesh (which is on the top front of the device, above the display). If it appears blocked, use a clean, small, dry, soft-bristled brush to carefully and gently brush away any debris.
8. If you have paired with a Bluetooth headset that is nearby, either use the headset or turn Bluetooth off (choose Settings > General > Bluetooth).
9. Restart the iPhone.
10. If restarting the iPhone doesn't resolve the issue, try restoring the device.
11. If the issue persists, go to the Service Answer Center - iPhone for information on service.
Thanks,
Matt M.

Can't access my Directory Server using the Console installed on a machine

can't access my Directory Server using the Console installed on a remote server, lookied into knowledge base article 4693, but still same any idea ?

I too am having problems accessing Directory server from Netscape Console installed on Winxp.
If I try to open Directory server it doesn't give any error. No windows nothing.
If I try th same from the machine on which it is installed everything is fine. What is strange is that it did open a couple of times. But at the same time I can open the admin server, Netscape Messaging server from the xp box. Searching all over for a solution. Any help/pointers would be greatly appreciated.
Config details:
iDS4.13, iMS 5.0, running on Sol 8 box
Netscape Console 4.2 on WinXP.
Thanks

How to configure the mac mini to allow the clients to access both partitions...the client will only see the one we are logged into at the server???

if possible??? how do we configure the mac mini to allow the clients to access both partitions...the client will only see the one we are logged into at the server???

You have to explicitly share directories on external/secondary volumes.
Use the Server admin app to configure file sharing, and select which directory/directories on the second drive you want to share, then they'll be available to clients.

DPM failed to communicate with the protection agent on DPM 2010 SERVER because the agent is not responding. (ID 43 Details: Internal error code: 0x8099090E)

Hi everyone,
Backup jobs for protected members are intermittently failing with the following error on the DPM server:
DPM failed to communicate with the protection agent on <DPM 2010 SERVER> because the agent is not responding. (ID 43 Details: Internal error code: 0x8099090E)
Why does the DPM server failing to see it's own DPM agent cause the backup job for another server to fail? One day a backup will work fine, the next it may fail; and the next back to normal again...
The following error is recorded in the Service Control Manager event log on the DPM server just prior to the above error:
A timeout was reached (30000 milliseconds) while waiting for the DPMRA service to connect.
Thank you.
With regards,
Rob

Hello,
I have read these entire postings and see that my problems match most of the above problems.
I believe we have tried all of the ideas in this blog and lots of other ideas from other forums and internet searches.
We have about 80 small databases protected and set at 15 minute incremental and most will work but some fail. When they fail the most common, but not only error, is something like "DPM
failed to communicate with the protection agent on <DPM 2010 SERVER> because the agent is not responding. (ID 43 Details: Internal error code: 0x8099090E)". The alert is inactivated in the DPM Console, and the backups resume as normal."
Since later jobs are successful I thought all was well. All was well until I went to restore from incremental backups. We worked for two days (day and night work) to restore
from a corrupted virtual disk on our SQL Server 2008 R2. I suspect DPM had something to do with the corrupted virtual disk. All I know is that we never had this problem until installing DPM. Here is what we encountered when we went to restore
from the protection points:
* Restore jobs take a minimum of 15 minutes for jobs that are 45 MB or 2 GB.
* If you pick a backup from the list of recovery points that is not valid the job runs for 15 minutes and then "Failed".
* You cannot rerun the job because SQL Server 2008 has the table being recovered as <tablename> (recovering) and a retry will not work. Of course time is wasted while waiting
to see if it worked.
* Eventually you realize that even after dropping the table in the (recovering) mode in SQL that the restore point must be bad or possibly one of this failed recovery points.
* So begins the quest to start restoring recovery points one by one and 15 minutes by 15 minutes until you find one that actually restores to a SQL Instance.
* If you have 80 of these to do and you average trying three recovery points and each takes 15 minutes, not to mention the time to drop the table in SQL, well that time adds up to 3,600
minutes of trial and error. 60 hours of trial and error, wow not much of a savings using DPM over a SQL backup plan.
* And then you have to explain to your customers that their databases were restored but you do not know at what point the DB was restored.
All in all it seems like DPM concept is great but like many backups the backup plan looks good on paper but actually restoring a backup is quite a different matter.
I don't know if anyone has ever solved the problems presented in this forum but if they have then I wish they would post and if no one has solved the problem then shame on DPM.
Good luck everyone, but I for one have spent about two months on trying to protect and restore consistently. I have never had one day of consistent and reliable restore points. I
am going back to sql management plans for my backups. I have never, in 10 years had a sql generated backup fail me. Never.
gbl

ASA 5505 Static hosts cannot access outside

I'm replacing an old PIX with a second hand ASA firewall.
I have configured the ASA in a very similar manner to how the PIX was set up but I'm having trouble with some hosts on the inside accessing the Internet. Any inside hosts which use DHCP work fine. Any inside hosts with a static IP (and configured on the ASA with a "static" rule) cannot access the Internet. For example, in the config below the server daviker-dialler cannot access the Internet.
I've spent a few days working on this now and have started from scratch several times but I'm not getting anywhere.
Apologies for all the X's everywhere, didn't like to post anything sensitive on the Internet. If I've obscured something pertinent let me know.
Any advice would be greatly appreciated! Thanks.
: Saved
ASA Version 7.2(3)
hostname fw-1
domain-name XXXX
enable password XXXX encrypted
names
name 92.X.X.61 bb-office
name 92.X.X.128 gl-office
name 10.0.0.117 daviker-dialler_in
name 77.X.X.117 daviker-dialler_out
name 10.0.0.112 data-2_in
name 77.X.X.112 data-2_out
name 10.0.0.81 corp-1_in
name 77.X.X.81 corp-1_out
name 10.0.0.111 data-1_in
name 77.X.X.210 user_75
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 77.X.X.66 255.255.255.192
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
passwd XXXX encrypted
ftp mode passive
dns server-group DefaultDNS
domain-name XXXX
access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq 5900
access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq 4040
access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq 9876
access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq sip
access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq www
access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq https
access-list inbound extended permit udp host bb-office host daviker-dialler_out eq sip
access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq 1433
access-list inbound extended permit udp host bb-office host daviker-dialler_out eq netbios-ns
access-list inbound extended permit udp host bb-office host daviker-dialler_out eq netbios-dgm
access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq netbios-ssn
access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq 445
access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq 4040
access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq 9876
access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq sip
access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq www
access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq https
access-list inbound extended permit udp host gl-office host daviker-dialler_out eq sip
access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq 1433
access-list inbound extended permit udp host gl-office host daviker-dialler_out eq netbios-ns
access-list inbound extended permit udp host gl-office host daviker-dialler_out eq netbios-dgm
access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq netbios-ssn
access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq 445
access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq 5900
access-list inbound extended permit tcp any host data-2_out eq ssh
access-list inbound extended permit tcp any host corp-1_out eq ssh
access-list inbound extended permit tcp any host corp-1_out eq www
access-list inbound extended permit tcp any host corp-1_out eq pop3
access-list inbound extended permit tcp any host corp-1_out eq imap4
access-list inbound extended permit tcp any host corp-1_out eq smtp
access-list inbound extended permit tcp any host corp-1_out eq 995
access-list inbound extended permit tcp any host corp-1_out eq 465
access-list inbound extended permit tcp any host corp-1_out eq 993
access-list inbound extended permit tcp any host corp-1_out eq 8008
access-list inbound extended permit udp 77.X.X.64 255.255.255.192 host 77.X.X.113 eq netbios-ns
access-list inbound extended permit udp 77.X.X.64 255.255.255.192 host 77.X.X.113 eq netbios-dgm
access-list inbound extended permit tcp 77.X.X.64 255.255.255.192 host 77.X.X.113 eq netbios-ssn
access-list inbound extended permit tcp 77.X.X.64 255.255.255.192 host 77.X.X.113 eq 445
access-list inbound extended permit udp any host 77.X.X.113 eq netbios-ns
access-list inbound extended permit udp any host 77.X.X.113 eq netbios-dgm
access-list inbound extended permit tcp any host 77.X.X.113 eq netbios-ssn
access-list inbound extended permit tcp any host 77.X.X.113 eq 445
access-list inbound extended permit tcp host bb-office host data-2_out eq 5901
access-list inbound extended permit tcp host bb-office host data-2_out eq 3690
access-list inbound extended permit tcp host bb-office host data-2_out eq www
access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq 3389
access-list inbound extended permit tcp host 2.X.X.18 host data-2_out eq 3306
access-list inbound extended permit tcp any host data-2_out eq 3306
access-list inbound extended permit tcp host 212.X.X.7 host daviker-dialler_out eq 5900
access-list inbound extended permit tcp host bb-office host data-2_out eq 3306
access-list inbound extended permit tcp host user_75 host daviker-dialler_out eq 1433
access-list inbound extended permit tcp host user_75 host daviker-dialler_out eq 5900
access-list inbound extended permit tcp host user_75 host data-2_out eq 3690
access-list inbound extended permit tcp host user_75 host data-2_out eq www
access-list inbound extended permit tcp host user_75 host data-2_out eq 3306
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-523.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) daviker-dialler_out daviker-dialler_in netmask 255.255.255.255
static (inside,outside) corp-1_out corp-1_in netmask 255.255.255.255
static (inside,outside) data-2_out data-2_in netmask 255.255.255.255
static (inside,outside) 77.X.X.113 data-1_in netmask 255.255.255.255
access-group inbound in interface outside
route outside 0.0.0.0 0.0.0.0 77.X.X.65 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
aaa authentication ssh console LOCAL
aaa authentication telnet console LOCAL
aaa authorization command LOCAL
http server enable
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet 0.0.0.0 0.0.0.0 inside
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 inside
ssh timeout 5
console timeout 0
dhcpd dns 77.X.X.91 8.8.8.8
dhcpd domain cagltd.net
dhcpd auto_config outside
dhcpd address 10.0.0.20-10.0.0.40 inside
dhcpd enable inside
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
username matt password XXXX encrypted
prompt hostname context
Cryptochecksum:00af76f23831b8c828fc6677c9069072
: end

Hi Jouni,
Thanks for the info.
I didn't have icmp traffic allowed, so I knew ping wouldn't be working. I was testing using http.
I have enabled icmp and dhcp clients can ping outside. Static nat clients can't ping outside. Static clients also cannot use outbound http.
As suggested, I have run some packet traces.
From a static nat client on the ASA:
fw-1# packet-tracer input inside tcp 10.0.0.81 80 173.203.209.67 80
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list
Phase: 2
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 3
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   0.0.0.0         0.0.0.0         outside
Phase: 4
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 5
Type: NAT
Subtype:
Result: ALLOW
Config:
static (inside,outside) corp-1_out corp-1_in netmask 255.255.255.255
match ip inside host corp-1_in outside any
    static translation to corp-1_out
    translate_hits = 668, untranslate_hits = 2
Additional Information:
Static translate corp-1_in/0 to corp-1_out/0 using netmask 255.255.255.255
Phase: 6
Type: NAT
Subtype: host-limits
Result: ALLOW
Config:
static (inside,outside) corp-1_out corp-1_in netmask 255.255.255.255
match ip inside host corp-1_in outside any
    static translation to corp-1_out
    translate_hits = 668, untranslate_hits = 2
Additional Information:
Phase: 7
Type: HOST-LIMIT
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 8
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 9
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 1759, packet dispatched to next module
Phase: 10
Type: ROUTE-LOOKUP
Subtype: output and adjacency
Result: ALLOW
Config:
Additional Information:
found next-hop 77.X.X.65 using egress ifc outside
adjacency Active
next-hop mac address 0017.0f13.5000 hits 1
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: allow
This looks fine to me, but as I say, an outbound tcp port 80 connection from the actual machine on 10.0.0.81 fails.
Here is a similar trace from a dhcp client to the same destination:
fw-1# packet-tracer input inside tcp 10.0.0.20 80 173.203.209.67 80
Phase: 1
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 2
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   0.0.0.0         0.0.0.0         outside
Phase: 3
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 4
Type: NAT
Subtype:
Result: ALLOW
Config:
nat (inside) 1 0.0.0.0 0.0.0.0
match ip inside any outside any
    dynamic translation to pool 1 (77.74.111.66 [Interface PAT])
    translate_hits = 990, untranslate_hits = 226
Additional Information:
Dynamic translate 10.0.0.20/80 to 77.74.111.66/1 using netmask 255.255.255.255
Phase: 5
Type: NAT
Subtype: host-limits
Result: ALLOW
Config:
nat (inside) 1 0.0.0.0 0.0.0.0
match ip inside any inside any
    dynamic translation to pool 1 (No matching global)
    translate_hits = 0, untranslate_hits = 0
Additional Information:
Phase: 6
Type: HOST-LIMIT
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 7
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 8
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 1771, packet dispatched to next module
Phase: 9
Type: ROUTE-LOOKUP
Subtype: output and adjacency
Result: ALLOW
Config:
Additional Information:
found next-hop 77.X.X.65 using egress ifc outside
adjacency Active
next-hop mac address 0017.0f13.5000 hits 5
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: allow
I can see the difference in the NAT translation section. A real outbound tcp port 80 connection from the actual machine on 10.0.0.20 works fine.
Finally, for the sake of comparison, I ran a similar packet trace using a static nat IP on the old PIX firewall:
old-fw-1# packet-tracer input inside tcp 10.0.0.117 80 173.203.209.67 80
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list
Phase: 2
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 3
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   0.0.0.0         0.0.0.0         outside
Phase: 4
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 5
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
class-map inspection_default
match default-inspection-traffic
policy-map global_policy
class inspection_default
inspect http
service-policy global_policy global
Additional Information:
Phase: 6
Type: NAT
Subtype:
Result: ALLOW
Config:
static (inside,outside) daviker-dialler_out daviker-dialler_in netmask 255.255.255.255
nat-control
match ip inside host daviker-dialler_in outside any
    static translation to daviker-dialler_out
    translate_hits = 17132, untranslate_hits = 1277850
Additional Information:
Static translate daviker-dialler_in/0 to daviker-dialler_out/0 using netmask 255.255.255.255
Phase: 7
Type: NAT
Subtype: host-limits
Result: ALLOW
Config:
static (inside,outside) daviker-dialler_out daviker-dialler_in netmask 255.255.255.255
nat-control
match ip inside host daviker-dialler_in outside any
    static translation to daviker-dialler_out
    translate_hits = 17132, untranslate_hits = 1277850
Additional Information:
Phase: 8
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 9
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 1006075, packet dispatched to next module
Phase: 10
Type: ROUTE-LOOKUP
Subtype: output and adjacency
Result: ALLOW
Config:
Additional Information:
found next-hop 78.X.X.69 using egress ifc outside
adjacency Active
next-hop mac address 0017.0f13.5000 hits 572133
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: allow
Outbound traffic from static nat hosts on the old PIX firewall works fine. One glaring difference is that the PIX is inspecting http traffic, but surely this is a red herring. Another difference is that the old and new firewalls have different gateways / default routes & different outside IP addresses. As the new ASA firewall (and its dhcp hosts) can talk to the outside world quite happily I don't think this is relevant.
I wondered whether it might be down to the difference in the inside (255.255.255.0) and outside (255.255.255.192) subnets. The set up is the same on the PIX, but I wondered whether some other line of config might be required on the ASA to handle it. I adjusted the subnet of the inside interface on the ASA to match the outside one (both 255.255.255.192) but it didn't make any difference.
So I'm puzzled!

ASA 5505 VPN can't access inside host

I have setup remote VPN access on a ASA 5505 but cannot access the host or ASA when I login using the VPN. I can connect with the Cisco VPN client and the VPN light is on on the ASA and it shows that I'm connected. I have the correct Ip address but I cannot ping or connect to any of the internal addresses. I cannot find what I'm missing. I have the VPN bypassing the interface ACLs. Since I can login but not go anywhere I feel certian I missed something.
part of config below
interface Vlan1
nameif inside
security-level 100
ip address 10.1.1.1 255.255.255.0
ip local pool xxxx 10.1.1.50-10.1.1.55 mask 255.255.255.0
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map outside_dyn_map 20 set pfs
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 40 set pfs
crypto dynamic-map outside_dyn_map 40 set transform-set ESP-3DES-SHA
crypto dynamic-map inside_dyn_map 20 set pfs
crypto dynamic-map inside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic inside_dyn_map
crypto map inside_map interface inside
crypto isakmp enable inside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
service-policy global_policy global
group-policy xxxxxxx internal
group-policy xxxxxxx attributes
banner value xxxxx Disaster Recovery Site
wins-server none
dns-server value 24.xxx.xxx.xx
vpn-access-hours none
vpn-simultaneous-logins 3
vpn-idle-timeout 30
vpn-session-timeout none
vpn-filter none
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelall
default-domain none
secure-unit-authentication disable
user-authentication disable
user-authentication-idle-timeout none
ip-phone-bypass disable
leap-bypass disable
nem disable
nac disable
nac-sq-period 300
nac-reval-period 36000
nac-default-acl none
address-pools value xxxxxx
smartcard-removal-disconnect enable
client-firewall none
webvpn
functions url-entry
vpn-nac-exempt none
no vpn-addr-assign aaa
no vpn-addr-assign dhcp
tunnel-group xxxx type ipsec-ra
tunnel-group xxxx general-attributes
address-pool xxxx
default-group-policy xxxx
tunnel-group blountdr ipsec-attributes
pre-shared-key *

I get the banner and IP adress info...
This is what the client log provides...
1 13:45:32.942 05/30/08 Sev=Warning/2 CVPND/0xE3400013
AddRoute failed to add a route: code 87
Destination 172.20.255.255
Netmask 255.255.255.255
Gateway 10.1.2.1
Interface 10.1.2.5
2 13:45:32.942 05/30/08 Sev=Warning/2 CM/0xA3100024
Unable to add route. Network: ac14ffff, Netmask: ffffffff, Interface: a010205, Gateway: a010201.

ASA 5505 & VPN Client blocking access to local lan

I have setup a IPSec vpn client connection to a Cisco ASA 5505, when I connect to the unit it fully authenticates and issues me an ip address on the local lan however when I attempt to connect to any service on the local lan the following message is displayed in the log can you help:
Teardown UDP connection 192.168.110.200 53785 192.168.110.21 53 outside:192.168.110.200/53785(LOCAL\username) to inside 192.168.110/53
See the attached file for a sanitised version of the config.

This is a sanitised version of the crypto dump, I have changed the user and IP addresses
ASA5505MAN# debug crypto ikev1 7
ASA5505MAN# debug crypto ipsec 7
ASA5505MAN# Jul 24 15:49:03 [IKEv1]IP = x.x.x.x, IKE_DECODE RECEIVED Message (msgid=fbc167de) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing hash payload
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing notify payload
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Received keep-alive of type DPD R-U-THERE (seq number 0xa6dcb72)
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Sending keep-alive of type DPD R-U-THERE-ACK (seq number 0xa6dcb72)
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing blank hash payload
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing qm hash payload
Jul 24 15:49:03 [IKEv1]IP = x.x.x.x, IKE_DECODE SENDING Message (msgid=515fbf7e) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jul 24 15:49:18 [IKEv1]IP = x.x.x.x, IKE_DECODE RECEIVED Message (msgid=2fe7cf10) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing hash payload
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing notify payload
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Received keep-alive of type DPD R-U-THERE (seq number 0xa6dcb73)
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Sending keep-alive of type DPD R-U-THERE-ACK (seq number 0xa6dcb73)
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing blank hash payload
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing qm hash payload
Jul 24 15:49:18 [IKEv1]IP = x.x.x.x, IKE_DECODE SENDING Message (msgid=e450c971) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jul 24 15:49:28 [IKEv1]IP = x.x.x.x, IKE_DECODE RECEIVED Message (msgid=e6c212e7) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing hash payload
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing notify payload
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Received keep-alive of type DPD R-U-THERE (seq number 0xa6dcb74)
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Sending keep-alive of type DPD R-U-THERE-ACK (seq number 0xa6dcb74)
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing blank hash payload
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing qm hash payload
Jul 24 15:49:28 [IKEv1]IP = x.x.x.x, IKE_DECODE SENDING Message (msgid=af5953c7) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
This is the isakmp dump
ASA5505MAN# show crypto isakmp
IKEv1 SAs:
   Active SA: 2
    Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 2
1   IKE Peer: x.x.x.x
    Type    : L2L             Role    : initiator
    Rekey   : no              State   : MM_ACTIVE
2   IKE Peer: x.x.x.x
    Type    : user            Role    : responder
    Rekey   : no              State   : AM_ACTIVE
There are no IKEv2 SAs
Global IKEv1 Statistics
Active Tunnels:              1
Previous Tunnels:           40
In Octets:              322076
In Packets:               2060
In Drop Packets:            84
In Notifys:               1072
In P2 Exchanges:            35
In P2 Exchange Invalids:     0
In P2 Exchange Rejects:      0
In P2 Sa Delete Requests:   24
Out Octets:             591896
Out Packets:              3481
Out Drop Packets:            0
Out Notifys:              2101
Out P2 Exchanges:          275
Out P2 Exchange Invalids:    0
Out P2 Exchange Rejects:     0
Out P2 Sa Delete Requests: 284
Initiator Tunnels:         231
Initiator Fails:           221
Responder Fails:            76
System Capacity Fails:       0
Auth Fails:                 54
Decrypt Fails:               0
Hash Valid Fails:            0
No Sa Fails:                30
Global IKEv2 Statistics
Active Tunnels:                          0
Previous Tunnels:                        0
In Octets:                               0
In Packets:                              0
In Drop Packets:                         0
In Drop Fragments:                       0
In Notifys:                              0
In P2 Exchange:                          0
In P2 Exchange Invalids:                 0
In P2 Exchange Rejects:                  0
In IPSEC Delete:                         0
In IKE Delete:                           0
Out Octets:                              0
Out Packets:                             0
Out Drop Packets:                        0
Out Drop Fragments:                      0
Out Notifys:                             0
Out P2 Exchange:                         0
Out P2 Exchange Invalids:                0
Out P2 Exchange Rejects:                 0
Out IPSEC Delete:                        0
Out IKE Delete:                          0
SAs Locally Initiated:                   0
SAs Locally Initiated Failed:            0
SAs Remotely Initiated:                  0
SAs Remotely Initiated Failed:           0
System Capacity Failures:                0
Authentication Failures:                 0
Decrypt Failures:                        0
Hash Failures:                           0
Invalid SPI:                             0
In Configs:                              0
Out Configs:                             0
In Configs Rejects:                      0
Out Configs Rejects:                     0
Previous Tunnels:                        0
Previous Tunnels Wraps:                  0
In DPD Messages:                         0
Out DPD Messages:                        0
Out NAT Keepalives:                      0
IKE Rekey Locally Initiated:             0
IKE Rekey Remotely Initiated:            0
CHILD Rekey Locally Initiated:           0
CHILD Rekey Remotely Initiated:          0
IKEV2 Call Admission Statistics
Max Active SAs:                   No Limit
Max In-Negotiation SAs:                 12
Cookie Challenge Threshold:          Never
Active SAs:                              0
In-Negotiation SAs:                      0
Incoming Requests:                       0
Incoming Requests Accepted:              0
Incoming Requests Rejected:              0
Outgoing Requests:                       0
Outgoing Requests Accepted:              0
Outgoing Requests Rejected:              0
Rejected Requests:                       0
Rejected Over Max SA limit:              0
Rejected Low Resources:                  0
Rejected Reboot In Progress:             0
Cookie Challenges:                       0
Cookie Challenges Passed:                0
Cookie Challenges Failed:                0
Global IKEv1 IPSec over TCP Statistics
Embryonic connections: 0
Active connections: 0
Previous connections: 0
Inbound packets: 0
Inbound dropped packets: 0
Outbound packets: 0
Outbound dropped packets: 0
RST packets: 0
Recevied ACK heart-beat packets: 0
Bad headers: 0
Bad trailers: 0
Timer failures: 0
Checksum errors: 0
Internal errors: 0
ASA5505MAN#
and this is the ipsec dump
ASA5505MAN# show crypto ipsec sa
interface: outside
    Crypto map tag: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: x.x.x.x
      local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
      remote ident (addr/mask/prot/port): (192.168.110.200/255.255.255.255/0/0)
      current_peer: x.x.x.x, username: username
      dynamic allocated peer ip: 192.168.110.200
      #pkts encaps: 778, #pkts encrypt: 778, #pkts digest: 778
      #pkts decaps: 1959, #pkts decrypt: 1959, #pkts verify: 1959
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 778, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #TFC rcvd: 0, #TFC sent: 0
      #Valid ICMP Errors rcvd: 0, #Invalid ICMP Errors rcvd: 0
      #send errors: 0, #recv errors: 0
      local crypto endpt.: x.x.x.x/4500, remote crypto endpt.: x.x.x.x/54599
      path mtu 1500, ipsec overhead 82(52), media mtu 1500
      PMTU time remaining (sec): 0, DF policy: copy-df
      ICMP error validation: disabled, TFC packets: disabled
      current outbound spi: 532B60D0
      current inbound spi : 472C8AE7
    inbound esp sas:
      spi: 0x472C8AE7 (1194101479)
         transform: esp-aes esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, IKEv1, }
         slot: 0, conn_id: 241664, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
         sa timing: remaining key lifetime (sec): 26551
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0xFFFFFFFF 0xFFFFFFFF
    outbound esp sas:
      spi: 0x532B60D0 (1395351760)
         transform: esp-aes esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, IKEv1, }
         slot: 0, conn_id: 241664, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
         sa timing: remaining key lifetime (sec): 26551
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001
    Crypto map tag: outside_map0, seq num: 1, local addr: x.x.x.x
      access-list outside_cryptomap_1 extended permit ip 192.168.110.0 255.255.255.0 192.168.0.0 255.255.0.0
      local ident (addr/mask/prot/port): (192.168.110.0/255.255.255.0/0/0)
      remote ident (addr/mask/prot/port): (192.168.0.0/255.255.0.0/0/0)
      current_peer: x.x.x.x
      #pkts encaps: 39333117, #pkts encrypt: 39333117, #pkts digest: 39333117
      #pkts decaps: 24914965, #pkts decrypt: 24914965, #pkts verify: 24914965
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 39333117, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #TFC rcvd: 0, #TFC sent: 0
      #Valid ICMP Errors rcvd: 0, #Invalid ICMP Errors rcvd: 0
      #send errors: 0, #recv errors: 0
      local crypto endpt.: x.x.x.x/0, remote crypto endpt.: x.x.x.x/0
      path mtu 1500, ipsec overhead 58(36), media mtu 1500
      PMTU time remaining (sec): 0, DF policy: copy-df
      ICMP error validation: disabled, TFC packets: disabled
      current outbound spi: F6943017
      current inbound spi : E6CDF924
    inbound esp sas:
      spi: 0xE6CDF924 (3872258340)
         transform: esp-3des esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, IKEv1, }
         slot: 0, conn_id: 163840, crypto-map: outside_map0
         sa timing: remaining key lifetime (kB/sec): (3651601/15931)
         IV size: 8 bytes
         replay detection support: Y
         Anti replay bitmap:
          0xFFFFFFFF 0xFFFFFFFF
    outbound esp sas:
      spi: 0xF6943017 (4136906775)
         transform: esp-3des esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, IKEv1, }
         slot: 0, conn_id: 163840, crypto-map: outside_map0
         sa timing: remaining key lifetime (kB/sec): (3561355/15931)
         IV size: 8 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001
ASA5505MAN#

ASA 5505 VPN can't access connected network

I have an ASA 5505 with ipsec VPN configured on it. I am able to connect to the ASA but I can't ping a connected network. I get a dhcp assigned address in the network I am trying to reach but can't access that network on Vlan5. Please help.
I attached the config.

I think final questions, can you have two nat statements that point to the same acl ie.
access-list no_nat extended permit ip 192.168.9.0 255.255.255.0 192.168.0.0 255.255.255.0
access-list no_nat extended permit ip 192.168.9.0 255.255.255.0 172.31.1.0 255.255.255.0
access-list no_nat extended permit ip 192.168.5.0 255.255.255.0 192.168.5.0 255.255.255.0
nat (inside) 0 access-list no_nat
nat (inside) 1 192.168.9.0 255.255.255.0
nat (fw-civic) 0 access-list no_nat
nat (fw-civic) 1 192.168.5.0 255.255.255.0
Or do I need to create a new acl for the fw-civic interface?
Thanks

ASA 5505 VPN - how to access Two private networks

Hello
i have cisco 5505 and i confirgured a remote VPN clients. here is my sceniro
cisco switch 2950   === holds two private network 192.168.8.x and 192.168.4.x
vlan 2 outside interface -    Eth0/0       155.155.155.x
Vlan 1 inside interface --       Eth 0/1    192.168.8.180
VPN pool ip address = 192.168.8.100 --110
i drag i cable from my cisco switch and put in to Eth0/1. and i want to access this twor private networks 192.168.4.x and 192.168.8.x .
now i can access to 192.168.8.x .
but i can't access 192.168.4.x .. please can any one help me that.
Regards
Thomas

configure a split tunnel list that contains the networks you want the client to access.
Sent from Cisco Technical Support iPad App

Cisco ASA 5505 not able to access flash

Hi All:
I have searched and searched all over the net for an answer to this question and have decided to just post it. I have a 5505 that was given to me by my job to use for working on my CCNA Sec. cert and did the following:
I plugged it in and booted it up just fine. Made config changes as I followed along with the examples in my CCNA Security book. Got to the point in chapter 14 where the initial setup happens to configure it for working with ASDM. I never did a write mem on it and decided to take it back to square one by unplugging it to allow it to lose the changes that I made. This is where things got ugly.
When it booted back up it got stuck in a bootup loop and couldn't find an IOS. After following all kinds of steps to boot to rommon and tftp another IOS and such (several times) I decided to follow another posting that said that the flash could be corrupted and to just delete it and start anew. Did that and through rommon as it would not boot up normally any more. After trying this over and over for the last couple hours I realized that it would boot from tftp so I did that in hopes of fixing the flash issue.
I've tried deleting it, and re-initializing it and formating it. But the thing is that it no longer SEES the disk0: mount point. I've used two different flash cards...the one that came with it and the one that I already had. With the cover off I can see that there is no activity light next to the flash drive when I issue a delete or initialize or format command.
Here is a copy of some of the output file. Any help or suggestions are greatly appreciated.
CISCO SYSTEMS
Embedded BIOS Version 1.0(12)11 04/30/08 15:45:41.19
Low Memory: 632 KB
High Memory: 507 MB
PCI Device Table.
Bus Dev Func VendID DevID Class              Irq
00 01 00   1022   2080 Host Bridge
00 01 02   1022   2082 Chipset En/Decrypt 11
00 0C 00   1148   4320 Ethernet           11
00 0D 00   177D   0003 Network En/Decrypt 10
00 0F 00   1022   2090 ISA Bridge
00 0F 02   1022   2092 IDE Controller
00 0F 03   1022   2093 Audio              10
00 0F 04   1022   2094 Serial Bus         9
00 0F 05   1022   2095 Serial Bus         9
Evaluating BIOS Options ...
Launch BIOS Extension to setup ROMMON
Cisco Systems ROMMON Version (1.0(12)11) #4: Thu May 1 14:50:05 PDT 2008
Platform ASA5505
Use BREAK or ESC to interrupt boot.
Use SPACE to begin boot immediately.
Ethernet0/0
MAC Address: 0023.339e.2a91
Link is UP
Please set ADDRESS Variable.
Please set SERVER Variable.
Please set IMAGE Variable.
Launching BootLoader...
Default configuration file contains 1 entry.
Boot mode is 1. Default entry is 1.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
Default configuration file contains 1 entry.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
Failsafe booting engaged.
Default configuration file contains 1 entry.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
CISCO SYSTEMS
Embedded BIOS Version 1.0(12)11 04/30/08 15:45:41.19
Low Memory: 632 KB
High Memory: 507 MB
PCI Device Table.
Bus Dev Func VendID DevID Class              Irq
00 01 00   1022   2080 Host Bridge
00 01 02   1022   2082 Chipset En/Decrypt 11
00 0C 00   1148   4320 Ethernet           11
00 0D 00   177D   0003 Network En/Decrypt 10
00 0F 00   1022   2090 ISA Bridge
00 0F 02   1022   2092 IDE Controller
00 0F 03   1022   2093 Audio              10
00 0F 04   1022   2094 Serial Bus         9
00 0F 05   1022   2095 Serial Bus         9
Evaluating BIOS Options ...
Launch BIOS Extension to setup ROMMON
Cisco Systems ROMMON Version (1.0(12)11) #4: Thu May 1 14:50:05 PDT 2008
Platform ASA5505
Use BREAK or ESC to interrupt boot.
Use SPACE to begin boot immediately.
Ethernet0/0
MAC Address: 0023.339e.2a91
Link is UP
Please set ADDRESS Variable.
Please set SERVER Variable.
Please set IMAGE Variable.
Launching BootLoader...
Default configuration file contains 1 entry.
Boot mode is 1. Default entry is 1.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
Default configuration file contains 1 entry.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
Failsafe booting engaged.
Default configuration file contains 1 entry.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
CISCO SYSTEMS
Embedded BIOS Version 1.0(12)11 04/30/08 15:45:41.19
Low Memory: 632 KB
High Memory: 507 MB
PCI Device Table.
Bus Dev Func VendID DevID Class              Irq
00 01 00   1022   2080 Host Bridge
00 01 02   1022   2082 Chipset En/Decrypt 11
00 0C 00   1148   4320 Ethernet           11
00 0D 00   177D   0003 Network En/Decrypt 10
00 0F 00   1022   2090 ISA Bridge
00 0F 02   1022   2092 IDE Controller
00 0F 03   1022   2093 Audio              10
00 0F 04   1022   2094 Serial Bus         9
00 0F 05   1022   2095 Serial Bus         9
Evaluating BIOS Options ...
Launch BIOS Extension to setup ROMMON
Cisco Systems ROMMON Version (1.0(12)11) #4: Thu May 1 14:50:05 PDT 2008
Platform ASA5505
Use BREAK or ESC to interrupt boot.
Use SPACE to begin boot immediately.
Ethernet0/0
MAC Address: 0023.339e.2a91
Link is UP
Please set ADDRESS Variable.
Please set SERVER Variable.
Please set IMAGE Variable.
Launching BootLoader...
Default configuration file contains 1 entry.
Boot mode is 1. Default entry is 1.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
Default configuration file contains 1 entry.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
Failsafe booting engaged.
Default configuration file contains 1 entry.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
CISCO SYSTEMS
Embedded BIOS Version 1.0(12)11 04/30/08 15:45:41.19
Low Memory: 632 KB
High Memory: 507 MB
PCI Device Table.
Bus Dev Func VendID DevID Class              Irq
00 01 00   1022   2080 Host Bridge
00 01 02   1022   2082 Chipset En/Decrypt 11
00 0C 00   1148   4320 Ethernet           11
00 0D 00   177D   0003 Network En/Decrypt 10
00 0F 00   1022   2090 ISA Bridge
00 0F 02   1022   2092 IDE Controller
00 0F 03   1022   2093 Audio              10
00 0F 04   1022   2094 Serial Bus         9
00 0F 05   1022   2095 Serial Bus         9
Evaluating BIOS Options ...
Launch BIOS Extension to setup ROMMON
Cisco Systems ROMMON Version (1.0(12)11) #4: Thu May 1 14:50:05 PDT 2008
Platform ASA5505
Use BREAK or ESC to interrupt boot.
Use SPACE to begin boot immediately.
Ethernet0/0
MAC Address: 0023.339e.2a91
Link is UP
Please set ADDRESS Variable.
Please set SERVER Variable.
Please set IMAGE Variable.
Launching BootLoader...
Default configuration file contains 1 entry.
Boot mode is 1. Default entry is 1.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
Default configuration file contains 1 entry.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
Failsafe booting engaged.
Default configuration file contains 1 entry.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
CISCO SYSTEMS
Embedded BIOS Version 1.0(12)11 04/30/08 15:45:41.19
Low Memory: 632 KB
High Memory: 507 MB
PCI Device Table.
Bus Dev Func VendID DevID Class              Irq
00 01 00   1022   2080 Host Bridge
00 01 02   1022   2082 Chipset En/Decrypt 11
00 0C 00   1148   4320 Ethernet           11
00 0D 00   177D   0003 Network En/Decrypt 10
00 0F 00   1022   2090 ISA Bridge
00 0F 02   1022   2092 IDE Controller
00 0F 03   1022   2093 Audio              10
00 0F 04   1022   2094 Serial Bus         9
00 0F 05   1022   2095 Serial Bus         9
Evaluating BIOS Options ...
Launch BIOS Extension to setup ROMMON
Cisco Systems ROMMON Version (1.0(12)11) #4: Thu May 1 14:50:05 PDT 2008
Platform ASA5505
Use BREAK or ESC to interrupt boot.
Use SPACE to begin boot immediately.
Ethernet0/0
MAC Address: 0023.339e.2a91
Link is UP
Please set ADDRESS Variable.
Please set SERVER Variable.
Please set IMAGE Variable.
Launching BootLoader...
Default configuration file contains 1 entry.
Boot mode is 1. Default entry is 1.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
Default configuration file contains 1 entry.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
Failsafe booting engaged.
Default configuration file contains 1 entry.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
CISCO SYSTEMS
Embedded BIOS Version 1.0(12)11 04/30/08 15:45:41.19
Low Memory: 632 KB
High Memory: 507 MB
PCI Device Table.
Bus Dev Func VendID DevID Class              Irq
00 01 00   1022   2080 Host Bridge
00 01 02   1022   2082 Chipset En/Decrypt 11
00 0C 00   1148   4320 Ethernet           11
00 0D 00   177D   0003 Network En/Decrypt 10
00 0F 00   1022   2090 ISA Bridge
00 0F 02   1022   2092 IDE Controller
00 0F 03   1022   2093 Audio              10
00 0F 04   1022   2094 Serial Bus         9
00 0F 05   1022   2095 Serial Bus         9
Evaluating BIOS Options ...
Launch BIOS Extension to setup ROMMON
Cisco Systems ROMMON Version (1.0(12)11) #4: Thu May 1 14:50:05 PDT 2008
Platform ASA5505
Use BREAK or ESC to interrupt boot.
Use SPACE to begin boot immediately.
Ethernet0/0
MAC Address: 0023.339e.2a91
Link is UP
Please set ADDRESS Variable.
Please set SERVER Variable.
Please set IMAGE Variable.
Launching BootLoader...
Default configuration file contains 1 entry.
Boot mode is 1. Default entry is 1.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
Default configuration file contains 1 entry.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
Failsafe booting engaged.
Default configuration file contains 1 entry.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
CISCO SYSTEMS
Embedded BIOS Version 1.0(12)11 04/30/08 15:45:41.19
Low Memory: 632 KB
High Memory: 507 MB
PCI Device Table.
Bus Dev Func VendID DevID Class              Irq
00 01 00   1022   2080 Host Bridge
00 01 02   1022   2082 Chipset En/Decrypt 11
00 0C 00   1148   4320 Ethernet           11
00 0D 00   177D   0003 Network En/Decrypt 10
00 0F 00   1022   2090 ISA Bridge
00 0F 02   1022   2092 IDE Controller
00 0F 03   1022   2093 Audio              10
00 0F 04   1022   2094 Serial Bus         9
00 0F 05   1022   2095 Serial Bus         9
Evaluating BIOS Options ...
Launch BIOS Extension to setup ROMMON
Cisco Systems ROMMON Version (1.0(12)11) #4: Thu May 1 14:50:05 PDT 2008
Platform ASA5505
Use BREAK or ESC to interrupt boot.
Use SPACE to begin boot immediately.
Boot interrupted.
Ethernet0/0
MAC Address: 0023.339e.2a91
Link is UP
Use ? for help.
rommon #0> format disk0:
Invalid or incorrect command. Use 'help' for help.
rommon #0> ADDRESS=10.10.10.110
rommon #1> GATEWAY=10.10.10.1
rommon #2> SERVER=10.10.10.98
rommon #3> IMAGE=asa914-k8.bin
rommon #4> tftp
ROMMON Variable Settings:
ADDRESS=10.10.10.110
SERVER=10.10.10.98
GATEWAY=10.10.10.1
PORT=Ethernet0/0
VLAN=untagged
IMAGE=asa914-k8.bin
CONFIG=
LINKTIMEOUT=20
PKTTIMEOUT=4
RETRY=20
tftp [email protected] via 10.10.10.1
Received 27076608 bytes
Launching TFTP Image...
Cisco Security Appliance admin loader (3.0) #0: Thu Dec 5 19:38:43 PST 2013
Platform ASA5505
Loading...
IO memory blocks requested from bigphys 32bit: 9956
Àdosfsck 2.11, 12 Mar 2005, FAT32, LFN
Currently, only 1 or 2 FATs are supported, not 42.
dosfsck(/dev/hda1) returned 1
mount: mounting /dev/hda1 on /mnt/disk0 failed: Invalid argument
mount: mounting /dev/hda1 on /mnt/disk0 failed: Invalid argument
Processor memory 343932928, Reserved memory: 62914560
Total SSMs found: 0
Total NICs found: 10
88E6095 rev 2 Gigabit Ethernet @ index 09 MAC: 0000.0003.0002
88E6095 rev 2 Ethernet @ index 08 MAC: 0023.339e.2a90
88E6095 rev 2 Ethernet @ index 07 MAC: 0023.339e.2a8f
88E6095 rev 2 Ethernet @ index 06 MAC: 0023.339e.2a8e
88E6095 rev 2 Ethernet @ index 05 MAC: 0023.339e.2a8d
88E6095 rev 2 Ethernet @ index 04 MAC: 0023.339e.2a8c
88E6095 rev 2 Ethernet @ index 03 MAC: 0023.339e.2a8b
88E6095 rev 2 Ethernet @ index 02 MAC: 0023.339e.2a8a
88E6095 rev 2 Ethernet @ index 01 MAC: 0023.339e.2a89
y88acs06 rev16 Gigabit Ethernet @ index 00 MAC: 0023.339e.2a91
INFO: Unable to read firewall mode from flash
       Writing default firewall mode (single) to flash
INFO: Unable to read cluster interface-mode from flash
       Writing default mode "None" to flash
Verify the activation-key, it might take a while...
Failed to retrieve permanent activation key.
Running Permanent Activation Key: 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000
The Running Activation Key is not valid, using default settings:
Licensed features for this platform:
Maximum Physical Interfaces       : 8              perpetual
VLANs                             : 3              DMZ Restricted
Dual ISPs                         : Disabled       perpetual
VLAN Trunk Ports                  : 0              perpetual
Inside Hosts                      : 10             perpetual
Failover                          : Disabled       perpetual
Encryption-DES                    : Enabled        perpetual
Encryption-3DES-AES               : Disabled       perpetual
AnyConnect Premium Peers          : 2              perpetual
AnyConnect Essentials             : Disabled       perpetual
Other VPN Peers                   : 10             perpetual
Total VPN Peers                   : 12             perpetual
Shared License                    : Disabled       perpetual
AnyConnect for Mobile             : Disabled       perpetual
AnyConnect for Cisco VPN Phone    : Disabled       perpetual
Advanced Endpoint Assessment      : Disabled       perpetual
UC Phone Proxy Sessions           : 2              perpetual
Total UC Proxy Sessions           : 2              perpetual
Botnet Traffic Filter             : Disabled       perpetual
Intercompany Media Engine         : Disabled       perpetual
Cluster                           : Disabled       perpetual
This platform has a Base license.
Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
                             Boot microcode        : CN1000-MC-BOOT-2.00
                             SSL/IKE microcode     : CNLite-MC-SSLm-PLUS-2_05
                             IPSec microcode       : CNlite-MC-IPSECm-MAIN-2.09
Cisco Adaptive Security Appliance Software Version 9.1(4)
****************************** Warning *******************************
This product contains cryptographic features and is
subject to United States and local country laws
governing, import, export, transfer, and use.
Delivery of Cisco cryptographic products does not
imply third-party authority to import, export,
distribute, or use encryption. Importers, exporters,
distributors and users are responsible for compliance
with U.S. and local country laws. By using this
product you agree to comply with applicable laws and
regulations. If you are unable to comply with U.S.
and local laws, return the enclosed items immediately.
A summary of U.S. laws governing Cisco cryptographic
products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by
sending email to [email protected].
******************************* Warning *******************************
This product includes software developed by the OpenSSL Project
for use in the OpenSSL Toolkit (http://www.openssl.org/)
Copyright (C) 1995-1998 Eric Young ([email protected])
All rights reserved.
Copyright (c) 1998-2011 The OpenSSL Project.
All rights reserved.
This product includes software developed at the University of
California, Irvine for use in the DAV Explorer project
(http://www.ics.uci.edu/~webdav/)
Copyright (c) 1999-2005 Regents of the University of California.
All rights reserved.
Busybox, version 1.16.1, Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
Busybox comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.
DOSFSTOOLS, version 2.11, Copyright (C) 1989, 1991 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111-1307
675 Mass Ave, Cambridge, MA 02139
DOSFSTOOLS comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.
grub, version 0.94, Copyright (C) 1989, 1991 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111-1307
grub comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.
libgcc, version 4.3, Copyright (C) 2007 Free Software Foundation, Inc.
libgcc comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenseSee User Manual (''Licensing'') for details.
libstdc++, version 4.3, Copyright (C) 2007 Free Software Foundation, Inc.
libstdc++ comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.
Linux kernel, version 2.6.29.6, Copyright (C) 1989, 1991 Free Software
Foundation, Inc.
51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
Linux kernel comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.
module-init-tools, version 3.10, Copyright (C) 1989, 1991 Free Software
Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
module-init-tools comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.
numactl, version 2.0.3, Copyright (C) 2008 SGI.
Author: Andi Kleen, SUSE Labs
Version 2.0.0 by Cliff Wickman, Chritopher Lameter and Lee Schermerhorn
numactl comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.
pciutils, version 3.1.4, Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
pciutils comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.
readline, version 5.2, Copyright (C) 1989, 1991 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111 USA
readline comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.
udev, version 146, Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
udev comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.
Cisco Adapative Security Appliance Software, version 9.1,
Copyright (c) 1996-2013 by Cisco Systems, Inc.
Certain components of Cisco ASA Software, Version 9.1 are licensed under the GNU
Lesser Public License (LGPL) Version 2.1. The software code licensed under LGPL
Version 2.1 is free software that comes with ABSOLUTELY NO WARRANTY. You can
redistribute and/or modify such LGPL code under the terms of LGPL Version 2.1
(http://www.gnu.org/licenses/lgpl-2.1.html). See User Manual for licensing
details.
                Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
                Cisco Systems, Inc.
                170 West Tasman Drive
                San Jose, California 95134-1706
Insufficient flash space available for this request:
Size info: request:32 free:0 delta:32
Could not initialize system files in flash.
config_fetcher: channel open failed
ERROR: MIGRATION - Could not get the startup configuration.
INFO: Power-On Self-Test in process.
INFO: Power-On Self-Test complete.
INFO: MIGRATION - Saving the startup errors to file 'flash:upgrade_startup_errors_200804300128.log'
Pre-configure Firewall now through interactive prompts [yes]? n
Type help or '?' for a list of available commands.
ciscoasa> en
Password:
ciscoasa# format disk0:
Format operation may take a while. Continue? [confirm]
Format operation will destroy all data in "disk0:". Continue? [confirm]
Initializing partition - done!
Creating FAT16 filesystem
mkdosfs 2.11 (12 Mar 2005)
System tables written to disk
Format of disk0 complete
ciscoasa# format disk:
                 ^
ERROR: % Invalid input detected at '^' marker.
ciscoasa# format flash:
Format operation may take a while. Continue? [confirm]
Format operation will destroy all data in "flash:". Continue? [confirm]
Initializing partition - done!

Yeah...I think I found that one out the hard way already. I'll cross that bridge when I get to it. I want to get this issue fixed before I start thinking about the license issue.
ciscoasa#
ciscoasa#
ciscoasa#
ciscoasa# sh flash
--#-- --length-- -----date/time------ path
2403 0           Apr 30 2008 02:00:56 test
2285 196         Apr 30 2008 01:28:20 upgrade_startup_errors_200804300128.log
2283 0           Apr 30 2008 01:28:20 coredumpinfo
2284 59          Apr 30 2008 01:28:20 coredumpinfo/coredump.cfg
2280 0           Apr 30 2008 01:27:56 crypto_archive
2267 0           Apr 30 2008 01:27:38 log
0 bytes total (0 bytes free)
ciscoasa#
ciscoasa#
ciscoasa#
ciscoasa# sh disk0
--#-- --length-- -----date/time------ path
2403 0           Apr 30 2008 02:00:56 test
2285 196         Apr 30 2008 01:28:20 upgrade_startup_errors_200804300128.log
2283 0           Apr 30 2008 01:28:20 coredumpinfo
2284 59          Apr 30 2008 01:28:20 coredumpinfo/coredump.cfg
2280 0           Apr 30 2008 01:27:56 crypto_archive
2267 0           Apr 30 2008 01:27:38 log
0 bytes total (0 bytes free)
ciscoasa#

[SOLVED] Can't access my home server from the outside

Hi all,
I have installed Arch on a Raspberry Pi and am trying to set up a home server. Right now, I am running a simple HTTP server (using node.js, if that matters) on port 8080. From my LAN, I can access the server all right.
From the outside, it seems that the traffic does actually reach the computer (I conclude this from the blinking diode indicating network traffic). However, all requests time out. Interestingly, if I kill the server while a request is pending, the timeout occurs right away.
I have no idea what is causing this. I have checked for iptables rules, but there seem to be none. What is blocking the traffic and how can I find out?
EDIT: Nevermind, I was testing incorrectly -- the traffic did reach the Raspberry Pi, but the return traffic did not reach my test computer because it was blocked by the router's firewall. Testing from TOR works just fine.
Last edited by MrAllan (2013-12-24 12:01:42)

I too am having problems accessing Directory server from Netscape Console installed on Winxp.
If I try to open Directory server it doesn't give any error. No windows nothing.
If I try th same from the machine on which it is installed everything is fine. What is strange is that it did open a couple of times. But at the same time I can open the admin server, Netscape Messaging server from the xp box. Searching all over for a solution. Any help/pointers would be greatly appreciated.
Config details:
iDS4.13, iMS 5.0, running on Sol 8 box
Netscape Console 4.2 on WinXP.
Thanks

G770 - Returning to store - Cant access Execute Disable Bits in the BIOS

Sigh...
I just bought a sharp looking G770. I am a trainer, so I need the laptop to run Win2008 R2 Hyper-V for MS pre-configured labs. I was able to get Hyper-V runnning, but could not bring the hyper-v nodes online. in troubleshooting, i realized that the BIOS did not include the Execute Disable Bits. I can access and enable virtualization in the BIOS.
Odd though - I can load Win 7, 64-bit ultimate and and run Virtual PC with no problem.

Quote
only p45 neo .. without F
P45 Neo-F and P45 Neo are identical.
Quote
whats the fastest cpu for this mainboard ? where can i find a list)
On the MSI Product Site for your Board:
http://global.msi.eu/index.php?func=prodcpu2&prod_no=1482&maincat_no=1&orderby=cpu_speed%20ASC#menu
Quote
its a 2.33ghz quadcore now
Must be a Q8200 then. But which one exactly? There are three different revisions. In any case, if your really have BIOS v1.0, you need a BIOS Update to ensure proper CPU Support.
Quote
P-45 neo-f(outside box) / ms-7519(sandra)
BIOS : 64-0100-009999-00101111-081208-Eaglelake
version: 1.0
Do not trust Sandra for board and BIOS Information. Please check your current BIOS Version in the BIOS Setup under Standard CMOS Features -> System Information.
Before posting another reply here, please read this:
>>Posting Guide<<

HT4061 i cant access my phone to provide the serial number and i want to talk to apple support

my screen on my iphone 4s is broken and i want to back up my phone on itunes but it is asking me to allow access to my phone by responding on my phone of which i cant because it is broken. is there another way to do so?

Hi mikevickie,
Thanks for visiting Apple Support Communities.
If you only see the "connect to iTunes" screen on your iPhone, the steps in this article can help:
If you can't update or restore your iOS device
http://support.apple.com/kb/ht1808
Best,
Jeremy

Asa 5505, the outside cant access to a server in the inside

Similar Messages

Maybe you are looking for