Audio Cuts when recording is enable. (Quality Manager)

Hi
I have deployed a recording QM solution (QM 8.5.2(SR2), CCX 8.5.1(SR4), CUCM 9.1) and I have a critical issue about the quality of the calls.
I'm using a Network Recording using Built in Bridge phone feature.
When a caller call to the agent and the recording is enable, the audio from agent to caller has a lot of cuts. Most than 50% time.
When the call is no recorded works fine.
Any idea?
Thank you
Best regards

Fix it.
It was g722 and iBLC codec. They were activated in service parameters. Just desactivated them and reset the phones.
I hope it helps.
Best Regards

Similar Messages

Any way to boost audio input when recording?

Hi; I have been recording speech interviews with Audio-Technica mics on a ProTools set-up and they've sounded great.
I've recently tried recording using the mics in Garageband using a M-Audio Mobile Pre USB, but the audio levels are always too low unless the subject is an inch or two from the mic, which isn't the best way to get quality audio.
Is there any way to boost the audio input when recording in GB or any other tricks people know of?
thx, Charlie

I'm actually having the same problem, except I'm recording straight into the computer (no interface).
I tried using an MBox, but the computer won't even recognize it...(if anyone's got suggestions for why that is, I'll gladly take them...).
My main question is the same as Charles's, however - how come the input level is so soft when recording using the "Built-In Input" (where I can use a mic, and have mobility) as opposed to the "Built-In Microphone"?

Lots of audio pops when recording from mixer

I'm using FCP 5.1.4 on a mac laptop (don't know what type it is, but think it's somewhat recent). I'm recording a stage play's audio.
Here's my audio flow:
Mixer's 1/4" headphone jack -> 1/4" Stereo audio cable -> 1/8" stereo adapter at other end (have also tried 1/8" mono) -> Laptop's microphone port (no other input audio port available)
I can get a good signal, but there's constant audio pops/clicks happening at a steady rate. I remember reading somewhere else that problems can arise when recording directly from a mixer due to the high signal strength coming from it. Any ideas why this is happening? How do I fix this?

Phillip Roh wrote:
What is a mic bus level output?
Most better mixers have direct bus ins and outs. Just like plugging in a mic.
Laptop doesn't have a line in port
Get a different computer if you're expecting to enjoy doing audio capture.
If i used the RCA or XLR output jacks, would the popping still occur?
Irrelevant, it's all about signal type, resistance, milliamperes, millivolts and milliwatts. Not connectors. You can put an XLR on your power supply and it wouldn't change the voltage.
I think my workplace may have a few USB audio things lying around. Like it has 2 XLR input ports, then connects to computer through USB. Do you know if they tend to need certain software, or if they're plug and play?< </div>
Unknown from here. this is not a FCP question.
bogiesan

Realtek HD audio problem when recording

Hello guys;
Been trying to do some recording for the first time since the OC was rebuilt. New specs as below.
(By the way, I couldn't get any sound at all until I reinstalled the UAA bus driver..., so it's thanks to this forum that I got sound in the first place!)
Anyway, the problem I now have is that basically the record level is way too high. I use Steinberg Clean 5.0 and was finding that although I could change the levels in the software, whatever level I recorded at I was suffering extreme amounts of clipping/distortion. (I should mention that the input is from a good quality hifi, I used it for many years for recording with my previous PC incarnation using my KT6 delta rig).
After much trial and error, I found that the only way to stop this is to have the recording sound level in volume set to - well it isn't numbered - it would be about 10%. I also discovered that although master recording level is adjustable the others - CD, mic, line, mix are greyed out.
The master level is really difficult to set (as I write I just discovered it's still distorting and I'll have to edged it down another couple of % towards zero), so I really want to change the "line" record level, but as I said it's greyed out.
In Realtek sound manager it's similar, in the record section there's an overall level control but no individual adjustments for record, only playback.
Incidentally playback works just fine!
Realtek drivers are latest 5.10.0.5928 downloaded yesterday from Realtek.
Anyone got any ideas please?
Andrew
Antec Sonata 2 case with 450w Smartpower PSU
+5V, 30A; +3.3V, 32A; +12V, 15A + 17A; -12V, 0.3A; -5V, 2A
MSI P43NEO-F
IntelE7400
4GB OCZ RAM
MSI ATI HD4650 1GB
120, 160, 500GB HDDs
2 optical drives
Etc
Windows XP Home SP3

Quote from: hu479as on 15-September-09, 04:10:19
I think the audio out must be fine as it works just fine for general listening to CDs, LPs (!!), whatever played from the hifi. No distortion even with volume level (in "volume control") set at 100% It's only the record level that's weird :-)
I'll try the headfone thing later, just trying to record something now!
Sorry, I'm not sure if this will help, as I haven't used Realtek HD audio for some time (always used add-in cards). But in my experience, most sound controllers have an option in mixer to select the recording source (e.g. Mic In, Line In, S/PDIF-In, Wave, CD, etc). In particular, many offer a recording source option for "What you hear" or "Stereo Mix". Essentially, this would combine and capture the audio from every available source, rather than from just a single source. I'm guessing it's a long shot but maybe you could change your recording source to this "mix" type (hopefully, something similar is available). To reduce noise you'll probably want to MUTE other sources (Wave, MIDI, CD, etc.), though you could leave them enabled as well (try to avoid things that would inject noise).
I'm only suggesting this approach because you mention that the playback from your hifi is completely fine. Only recording from line-in is distorted. So perhaps, you can work around the problem by recording the mixed playback. It shouldn't make any sense for this to be happening but maybe you'll be lucky?? My (worst-case) thought is that maybe your realtek HD's ADC is damaged and therefore playback is flawless but recording is flawed...
Another thought I had is mixer settings are often stored within an ini file. If you or someone else could identify the file(s), then you should be able to view, and in turn, modify the numeric playback and recording levels. That should aide you in adjusting the levels more precisely, rather than guessing levels via the obscure gui sliders.
It may turn out that none of my ideas are helpful, but I wish you good luck all the same.

How do I fix the Audio Delay when recording Voiceovers?

I've been recording voiceovers in Final Cut Pro X and noticed that its a huge delay in the audio when I play it back. The recording is like a second or two behind making the voiceovers sound wayyy off to whats actually goin gon in the video. Is there any fix to this or is this a hardware issue? I'm running Final Cut Pro off of an External harddrive since my Macbook Pro can't handle the program as well. Its a 2009 17 inch. 4 Gigs of ram....150 Gigs of storage space left running on Mavericks. Any info is appreciated.

The VO or the video is a connected clip. You can trim it and move it according to your needs. Or do I misunderstand the issue?
Russ
Message was edited by: Russ H to strike through three words

How do I make my audio better when recording videos?

what is the best way to enhance audio on videos I make with my iPhone 4?

      Thanks, Bobby
     All good advice.
     I went and checked out the link you provided, and started salivating immediately. But $200 is too much for me right now. Looked at the lav (what does that mean?) mic adjacent to it-- lovely, very portable, and almost affordable. I registered, and created a wish list. I think my wedding anniversary or something must be coming up soon...
       I was thinking about my barely-there audio today, and just for the fun of it checked my volume button. I NEVER turn it down. Never. But it was, by about half. Does this have any effect on recording, or just ringing? (Can you tell I'm almost totally techno-ignorant?)
       Something else occurred to me too. When I was shooting, twice so far (and I am cringing writing this), I was talking really low the whole time. Last night, cuz my hubby was asleep in the next room; this morning, because I didn't want to scare the birds I was videoing away...   uh.....   Well, DUH.
       Actually, I have already bought one of those little capsule mics, found it on Amazon. IT WON'T FIT ON MY PHONE WHILE THE CASE IS ON. And I am scared to death to take the case off! The thing's made out of glass, for cripes sake, and I am a CLUTZ.
       Thanks again!! I'll be coming up with plenty more stupid questions for quite a while, I'm sure

Intermittent audio buzz when recording with power adapter

While running my 13" Unibody MacBook Pro on the power adapter, I get an regularly pulsing buzz that affects audio recorded in through my Griffin iMic. There's a sample of the buzzing I recorded at http://drp.ly/lmd8R - it starts halfway through it. The buzzing starts a few seconds after plugging in the power adapter and stops a few seconds after plugging it in. The power adapter is grounded and the cord is separated from the audio cords. Any help would be appreciated.

Are the Mac and all of the connected devices plugged into the same grounded UPS or outlet strip?
When I had a similar problem I ended up having a very serious electrical wiring problem in my house–a poor earth-neutral bond in my case. You may want to have a professional electrician check things out.
Message was edited by: DaddyPaycheck

Audio levels when recording iPad video

how do i contro audio input levelsl when i record video on my iPad?

The best advice is to tell them their work is coming back non-compliant and you can't have that. Let them figure out why and solve it. (That's is part of their job, after all.)

Audio breakup when recording

Unusual set-up:
Using "HAUPTWERK", external software providing pipe organ samples developed from modeled organs.
Logic sends MIDI to the HAUPTWERK software through an "AU/VST Link" plug from Hauptwerk, and accepts audio through the same plugin.
When the external program is set up properly, Music Typing will play clear sounds from the organ samples selected by "pulling stops" on the HAUPTWERK software.
But when I hit the Record button, the sounds usually break up; seems to happen 9/10ths of the time.
Observed on 16 GB memory flash storage MBP. Using a basic version of the Hauptwerk software that uses no more than 3 GB memory.
(Anyone interested in organ software should visit http://hauptwerk.com.)

Thanks much for the hint.
Tried that - it was suggested in another topic, but might not have done the right thing.
Audio buffer set to 1024. Buffer range set to "Large".
Threads are "Automatic".
Note that I get broken sound after hitting the Play button as well.
Also, the breakup goes away after changing tracks several times.
---- Just noticed something strange:
There are 3 software instrument tracks, all of which use organ-software sounds. For some reason the level meters only show up in the first track no matter which of the others I play on, but I get the right sounds for each track.

Audio sync when recording downloaded

Hi, when I download a recording from the connect server as a flash file, the audio tends to get out of sync. Typically our recordings are around 1 - 2 hours long, so it can be quite annoying
Any hints on ways to avoid this, or software we can use to resync the audio?
Thanks heaps
Jim
http://www.theaviationindex.com

I'd like to tag along on this thread, if I may. Our organization has just signed up on a monthly program with Connect 8 and I am also having A/V sync issues on downloaded programs. As with the issue described in the post from HavillandHornet, we are having problems holding sync in our downloaced .fv's of programs , which range in 15-30 minutes in length.
I understand that .flvs were, originally at least, not created to hold sync for long periods, although we get pretty good results when just playing back the recording off the Adobe server. It's just the playback of the downloaded file that gives us trouble I'm wondering if there is any way to set the download to record in a more sync-friendly format? I'm certainly not having much luck in converting the .flv to an editable format, like .mov to make sync adjustments and cleaner trims.
We began using Connect 8 around the first week of May, and the upgrades your indicated may not yet be operable. What is the status on that? Will those fixes affect the sync integrity on the recorded download or just the online playback.
Any enlightenment, work arounds or general bright ideas would be very helpful.
garypickle55

Naming audio tracks when recording??

Is there a way of naming audio tracks so when you record them the actual name of the track exists in the audio folder??
When you record in an audio track in logic for the first time, it prompts you to name and select where the audio track will be saved. Now whatever tack I record I end up having the same name for ever track..

I did wonder if I should edit my answer with more detail
In the Set Audio Record Path box if you check "Use Audio Object Name For Filename" then the name of whichever track you have selected and and are recording to is used.

In FaceTime calls, other person's audio cuts when mine is sending (when I'm talking)...

I seem to remember a time when this wasn't the case... Maybe I'm misremembering?
In a FaceTime call, when I'm in the middle of speaking and the other side speaks, they can't be heard until I stop speaking.
I.e. Audio only goes one way at a time it seems.
This is extremely problematic in slightly noisy areas where there's some background traffic where I am having to mute my end everytime I finish saying something just so I can hear the other person at all.
Bandwidth is not an issue, and it
Am I crazy, or didn't it used to allow me to use the headphones as well as the microphone at the same time?

I have the exact same issue... I've been using a Jabra Extreme2 and just this weekend, bought a Plantronics Marque2 and today had the same issue, so it's clearly not the headset but the phone or OS.
I might try a restore and see if it helps...

Audio Mismatch When Recording from Camcorder

I am recording video from my Panasonic GS-180 camcorder using Quicktime Pro over a firewire cable, and the sound always gets off, eventually by more than 10 seconds. I have set the quality to "Device Native."
Any suggestions?
MacBook Pro Mac OS X (10.4.8) Quicktime 7.1.3

I doubt it will help, but you might try to do a fresh save on the video after fixing "timecode breaks" in the free MPEGStream app. Very nice application, and freely provided by an Italian video concern. It can also do batch mode, though maybe not for timecode break saves.
Ironic that video editing is made far more complete by adding this software to the more modest Mac arsenal.

No audio preview when recording with line-in

I am using my keyboard to record music- and it works ok- the only problem is, when i hit the keyboard it makes no sound in garageband. however, when i hit record and play my keyboard (still no sound) but it does record. then i can hit replay it and it sounds perfect.
is there a way that i can hear what i'm playing while i'm playing it? I'm using garageband 3.04
it is way too difficult not being able to hear what i'm playing. and i hate having to re-do and review a million times to get it perfect.

http://www.bulletsandbones.com/GB/GBFAQ.html#monitoron
(Let the page FULLY load. The link to your answer is at the top of your screen)

Why do I keep getting "Error getting push certificate" when trying to enable Profile Manager

I keep getting this stupid error message! The Stupid Workgroup manager doesn't work! Won't allow me to do anything! What is the point in that! Sorry, just having a rant as I have just purchased this server which I can't do anything with. Can't get Profile Manager working because I keep getting error getting push certificate and cannot associate any user with a group. I can delete groups and users from AD but just wont allow me to create anything. The padlock is open so am authenticated. WHAT IS GOING ON WITH APPLE!

And do you know what is really sad, 3 hours later and I am still waiting for a confirmation email from Apple. No wonder the UK use mostly Windows!

Audio Cuts when recording is enable. (Quality Manager)

Similar Messages

Maybe you are looking for