Authentication Fail?

Hi,
I'm having problem connecting my router to the sp.
I turned on debug ppp auth and debug ppp neg. Below are the debug output, can anyone help to determine what is the problem?
Oct 10 14:51:16.674: Vi1 AUTH: Timeout 1
Oct 10 14:51:16.674: Vi1 PAP: Using hostname from interface PAP
Oct 10 14:51:16.674: Vi1 PAP: Using password from interface PAP
Oct 10 14:51:16.674: Vi1 PAP: O AUTH-REQ id 107 len 29 from "username"
Oct 10 14:51:26.690: Vi1 AUTH: Timeout 2
Oct 10 14:51:26.690: Vi1 PAP: Using hostname from interface PAP
Oct 10 14:51:26.690: Vi1 PAP: Using password from interface PAP
Oct 10 14:51:26.690: Vi1 PAP: O AUTH-REQ id 108 len 29 from "username"
Oct 10 14:51:36.706: Vi1 AUTH: Timeout 3
Oct 10 14:51:36.706: Vi1 PAP: Using hostname from interface PAP
Oct 10 14:51:36.706: Vi1 PAP: Using password from interface PAP
Oct 10 14:51:36.706: Vi1 PAP: O AUTH-REQ id 109 len 29 from "username"
Oct 10 14:51:46.690: Vi1 PAP: I AUTH-NAK id 109 len 26 msg is "Authentication failed"
Oct 10 14:51:46.694: Vi1 LCP: I TERMREQ [Open] id 4 len 4
Oct 10 14:51:46.694: Vi1 LCP: O TERMACK [Open] id 4 len 4
Oct 10 14:51:46.694: Vi1 PPP: Sending Acct Event[Down] id[131]
Oct 10 14:51:46.694: Vi1 PPP: Phase is TERMINATING
Oct 10 14:51:46.698: %DIALER-6-UNBIND: Interface Vi1 unbound from profile Di1
Oct 10 14:51:46.706: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down
Oct 10 14:51:46.722: Vi1 LCP: State is Closed
Oct 10 14:51:46.722: Vi1 PPP: Phase is DOWN
Oct 10 14:52:08.706: Vi1 PPP: Phase is DOWN, Setup
Oct 10 14:52:08.710: %DIALER-6-BIND: Interface Vi1 bound to profile Di1
Oct 10 14:52:08.714: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up
Oct 10 14:52:08.714: Vi1 PPP: Treating connection as a callout
Oct 10 14:52:08.714: Vi1 PPP: Phase is ESTABLISHING, Active Open
Oct 10 14:52:08.714: Vi1 PPP: Authorization NOT required
Oct 10 14:52:08.714: Vi1 PPP: No remote authentication for call-out
Oct 10 14:52:08.718: Vi1 LCP: O CONFREQ [Closed] id 1 len 10
Oct 10 14:52:08.718: Vi1 LCP: MagicNumber 0x132A0FF2 (0x0506132A0FF2)
Oct 10 14:52:08.722: Vi1 LCP: I CONFACK [REQsent] id 1 len 10
Oct 10 14:52:08.722: Vi1 LCP: MagicNumber 0x132A0FF2 (0x0506132A0FF2)
Oct 10 14:52:10.702: Vi1 LCP: I CONFREQ [ACKrcvd] id 2 len 18
Oct 10 14:52:10.702: Vi1 LCP: MRU 1492 (0x010405D4)
Oct 10 14:52:10.702: Vi1 LCP: AuthProto PAP (0x0304C023)
Oct 10 14:52:10.702: Vi1 LCP: MagicNumber 0x8478E237 (0x05068478E237)
Oct 10 14:52:10.706: Vi1 LCP: O CONFNAK [ACKrcvd] id 2 len 8
Oct 10 14:52:10.706: Vi1 LCP: MRU 1500 (0x010405DC)
Oct 10 14:52:10.710: Vi1 LCP: I CONFREQ [ACKrcvd] id 3 len 18
Oct 10 14:52:10.710: Vi1 LCP: MRU 1500 (0x010405DC)
Oct 10 14:52:10.710: Vi1 LCP: AuthProto PAP (0x0304C023)
Oct 10 14:52:10.710: Vi1 LCP: MagicNumber 0x8478E237 (0x05068478E237)
Oct 10 14:52:10.710: Vi1 LCP: O CONFACK [ACKrcvd] id 3 len 18
Oct 10 14:52:10.714: Vi1 LCP: MRU 1500 (0x010405DC)
Oct 10 14:52:10.714: Vi1 LCP: AuthProto PAP (0x0304C023)
Oct 10 14:52:10.714: Vi1 LCP: MagicNumber 0x8478E237 (0x05068478E237)
Oct 10 14:52:10.714: Vi1 LCP: State is Open
Oct 10 14:52:10.714: Vi1 PPP: Phase is AUTHENTICATING, by the peer
Oct 10 14:52:10.714: Vi1 PAP: Using hostname from interface PAP
Oct 10 14:52:10.714: Vi1 PAP: Using password from interface PAP
Oct 10 14:52:10.714: Vi1 PAP: O AUTH-REQ id 110 len 29 from "username"
Oct 10 14:52:20.706: Vi1 AUTH: Timeout 1
Oct 10 14:52:20.706: Vi1 PAP: Using hostname from interface PAP
Oct 10 14:52:20.706: Vi1 PAP: Using password from interface PAP
Oct 10 14:52:20.706: Vi1 PAP: O AUTH-REQ id 111 len 29 from "username"
Oct 10 14:52:30.722: Vi1 AUTH: Timeout 2
Oct 10 14:52:30.722: Vi1 PAP: Using hostname from interface PAP
Oct 10 14:52:30.722: Vi1 PAP: Using password from interface PAP
Oct 10 14:52:30.722: Vi1 PAP: O AUTH-REQ id 112 len 29 from "username"

Is it possible to show the config at both ends. There can be many reasons for Auth failure. What is the auth mechanism u r trying ?

Similar Messages

  • SAP Business One Integration Services Authentication Failed

    Dear ,
    ALL SAP forum members,
    Iam Using SAP Business One 8.81 PL 06, Micorsoft SQL 2008 R2
    In SLD B1DI and  JDBC, the connections were tested successfully.
    Whenever I log into SBO, I am getting "SAP Business One Integration Services Authentication Failed" error message. I did extensive research on all possible SBO documents dating 1 year back especially in B1ic Troubleshooting Document (New and Old) and searched the length of the SBO forums, but I could not a solution.
    I uninstalled and reinstalled the B1f package many a time. The integration services we re also restarted many times and the connections were all tested successfully. Firewall, AntiVirus also checked.
    In the B1f, in the Monitoring Window, the login is "Ok" but the AuthCheck is "Failed". I checked Authent.Monitor->Authentic Info  and I found the following message under Action message "Wrong Usrname and Password".
    I debugged and i found again "/com.sap.b1i.vplatform.scenarios.authen/sap.Xcelsius/Authenticate_Check.bfd
    But could not understand much of it.
    But i could go no further. The experts are requested to suggest their solutions, If any, to me as Iam stuck in this phase for the last 3 week
    I hope some experts will guide me over this issue
    Thanks and regards
    Ashish Gupte

    Hi Konstantin Ryahovsky
    Thanks for your reply. My problem is solved.
    And frankly speaking i dont know how it was solved. I have not uninstall, install ,not even i had restarted the server also.
    only change i did in SLD >> Maintainance >>> cfg Runtime >>>> Put server IP address instead of server Name and restarted the services.
    Thanks & regards
    Ashish Gupte

  • Toshiba EXCITE Pro - WIFI connection. Authentication failed after update

    Hello.
    Just received this Tablet.
    Everything seemed ok while updating to the latest version (did that first to solve the heat problems).
    After the last update *i lost my WIfi connection. Authentication failed* (didnt change something - was connecting - updating ok 1 minute before the last update).
    After that i started testing ,Wps connection , No security Wifi etc etc.
    *Finally at a random time (and with the initial settings) i got connected*. After i shut down the tablet the same problem occured.
    After doing the same things again i finally got connected and this time it seems to be ok, even after i shut down the tablet.
    However this is frustrating.
    Maybe you have to sort this out?
    I have seen and other people returning this tablet after having this problem.
    It is not a hardware problem since its working ok before the update.
    Of course tried factory reset twice.
    Hope i dont have this problem again, *but i am informing in hope that you fix this in a future update.*

    Toshiba sent me the fix for this. Figured I would use Facebook and they sorted a solution straight away.
    It requires a complete reset. Not the soft reset from within Android.
    I'll post it here as they will check through moderation I guess.
    Thanks for sending a private message Ben. For us to get this resolved for you we would advise to perform a reset from the Android system recovery menu, to do the reset please follow these steps:
    The reset process will delete any data, settings, and applications on your tablet. You must have a backup of any data you wish to keep before proceeding.
    1. Make sure the tablet is off and not in standby.
    2. Hold down the Volume Up and Power buttons simultaneously until the two Android icons appear.
    3. Use the volume buttons to select the white box on the right.
    4. Once selected, press the power button.
    5. Use the volume buttons to select wipe cache partition and then press the power button.
    6. Select Yes and press the power button.
    7. Use the volume buttons to select wipe data/factory reset and then press the power button.
    8. Select Yes and press the power button.
    9. The tablet will now reset.
    If you have any issues after the reset please get back to us as soon as possible!
    Its been working well ever since. I guess the cache clean part might be the main one. You'll have to select the reboot yourself as I did at the end.
    Might be best to use Facebook i'll see if I can find my post as the response was quick and efficient unlike their responses in here. I.e nowt from them so far.
    They needed my name and serial numbers probably to log problems etc.
    Message was edited by: bensimmo

  • I'm trying to connect through the FTP client Filezilla. When I try to login with the wizard, it gives me a "503 Failure of Data Connection" reply; when I attempt to login myself, it gives me a "530 Login Authentication Failed." HELP!!!

    My current softward is: Mac OS X Lion 10.7.5 (11G63)
    When I attempt to use the Filezilla connection wizard I get the following message:
    Connecting to probe.filezilla-project.org
    Response: 220 FZ router and firewall tester ready
    USER FileZilla
    Response: 331 Give any password.
    PASS 3.7.1.1
    Response: 230 logged on.
    Checking for correct external IP address
    Retrieving external IP address from http://ip.filezilla-project.org/ip.php
    Checking for correct external IP address
    IP 27.0.19.56 ch-a-bj-fg
    Response: 200 OK
    PREP 52470
    Response: 200 Using port 52470, data token 1871898076
    PORT 27,0,19,56,204,246
    Response: 200 PORT command successful
    LIST
    Response: 150 opening data connection
    Response: 503 Failure of data connection.
    Server sent unexpected reply.
    Connection closed
    When I attempt to login Host/Username/Password myself I get the following message:
    Status:          Resolving address of amyhoney.com
    Status:          Connecting to 184.168.54.1:21...
    Status:          Connection established, waiting for welcome message...
    Response:          220---------- Welcome to Pure-FTPd [privsep] [TLS] ----------
    Response:          220-You are user number 12 of 500 allowed.
    Response:          220-Local time is now 04:05. Server port: 21.
    Response:          220-This is a private system - No anonymous login
    Response:          220 You will be disconnected after 3 minutes of inactivity.
    Command:          USER 5475****
    Response:          331 User 5475**** OK. Password required
    Command:          PASS ********************
    Response:          530 Login authentication failed
    Error:          Critical error
    Error:          Could not connect to server
    Now before anyone points out the obvious: my username and password are correct. I've already gone through changing them so I know they are.
    Additionally, I've pretty much tried EVERYTHING I've read online, from messing with "terminal" (and subsequently the FTP and STFP options) to changing the sharing options and turning on file sharing/remote management as well as just turning off my Firewall completely.
    Now I've used Filezilla before when I first published my site and everything worked fine. My site is published through Wordpress so most of my editing was done through simply logging into my "wp-login." I recently changed the theme and in order to change the header image in that theme I have to do it through my "wp-content" folder, which means I need to use Filezilla. I feel like a complete moron right now considering I've had my site for about a year and can't even doing something this simple.
    I've read that the newer version of Lion/Mountain Lion don't support automatice FTP anymore, which (as I mentioned prior) I attempted to fix through Terminal. However, nothing I do seem to do works.
    Can someone walk me through fixing this? And I do mean 'walk me through'. I'm not a tech-savvy nerd who knows all the lingo, I just know the basics so sorry if my ignorance offends you.
    HELP!!

    First be sure login and password are OK. Sometimes the address starts wit "http://..." and sometime starts with "ftp://...". Try both normal FTP access and Scure FTP access (SFTP). At the end, contact the site's provider.

  • OBIA 7.9.5 EBS Integration Not Logged On nQSError 43001 Authentication Fail

    Hi,
    I'm attempting to get Oracle Business Intelligence Applications 7.9.5 / OBIEE 10.1.3.3.2 integrated into the eBusiness Suite 11.5.10.2 per Metalink Note 552735.1. At the moment not an action link, just menu option to SA Administrator.
    I've run into and worked around a number of problems with the Initialization block variables setup in OracleBIAnalyticsApps.rpd and now no longer get errors in the NQServer.log after disabling Initialization Blocks for Siebel/Peoplesoft and disabling 2 EBS specific Init blocks that were erroring; 'Inventory Organizations' and 'Ledgers' I'll fix those later.
    However, now I get an error in the sawlog0.log file as follows:
    File: project/webodbcaccess/odbcconnectionimpl.cpp Line: 371
    Properties: ConnId-6,6;ThreadID-1145072560
    Location:
    saw.odbc.connection.open
    saw.connectionPool.getConnection
    saw.threadPool
    saw.threads
    Odbc driver returned an error (SQLDriverConnectW).
    State: 08004. Code: 10018. NQODBC [SQL_STATE: 08004|http://forums.oracle.com/forums/] [nQSError: 10018|http://forums.oracle.com/forums/] Access for the requested connection is refused.
    [nQSError: 43001|http://forums.oracle.com/forums/] Authentication failed for in repository Star: invalid user/password. (08004)
    Type: Error
    Severity: 42
    Time: Wed Dec 3 07:13:16 2008
    File: project/webconnect/connection.cpp Line: 276
    Properties: ThreadID-1145072560
    Location:
    saw.connectionPool.getConnection
    saw.threadPool
    saw.threads
    Authentication Failure.
    Odbc driver returned an error (SQLDriverConnectW).
    Can anyone point me in the right direction here?
    Thanks,
    Gareth

    The strange thing is both Gareth and I have configured OBIA/OBIEE on a Linux server and local authentication works fine. Once we enable external EBS authentication, we get the error listed above.
    Does anyone who has done the OBIA EBS integration with OBIEE running on Linux have an example of the odbc.ini file. It appears that even though we have reconfigured OracleBIAnalyticsApps.rpd to use OCI everywhere, that there is still some hard coded ODBC references for external authentication.
    We are configuring instanceconfig.xml as directed:
    Integrating Oracle Business Intelligence Applications with Oracle E-Business Suite
    https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=552735.1
    Configuring InstanceConfig.xml for External Authentication
    1. Modify the instanceconfig.xml file for the Oracle BI Presentation Services as shown below:
    <?xml version="1.0"?>
    <WebConfig>
    <ServerInstance>
    <CatalogPath>c:\temp\default</CatalogPath>
    <DSN>AnalyticsWeb</DSN>
    <Auth>
    <ExternalLogon enabled="true">
    <ParamList>
    <Param name="NQ_SESSION.ICX_SESSION_COOKIE"
    source="cookie"
    nameInSource="EBSAppsDatabaseSID"/>
    <Param name="NQ_SESSION.ACF"
    source="url"
    nameInSource="ACF"/>
    </ParamList>
    </ExternalLogon>
    </Auth>
    <!-- Other settings here. -->
    </ServerInstance>
    </WebConfig>
    2. The nameInSource for the cookie should be the same as the Oracle E-Business Suite application database SID name. To verify the name of the cookie, using Firefox, check the name of the cookie created under the us.oracle.com domain (or the domain where your Oracle E-Business Suite Application server is running). Please note that the cookie name is case sensitive.

  • BO XI 3.1 : Active Directory Authentication failed to get the Active Directory groups

    Dear all 
            In our environment, there are 2 domain (domain A and B); it works well all the time. Today, all the user belong to domain A are not logi n; for user in domain B, all of them can log in but BO server response is very slowly. and there is error message popup when opening Webi report for domain B user. Below are the error message: 
           " Active Directory Authentication failed to get the Active Directory groups for the account with ID:XXXX; pls make sure this account is valid and belongs to an accessible domain"
          Anyone has encountered similar issue?
       BO version: BO XI 3.1 SP5
       Authenticate: Windows AD
    Thanks and Regards

    Please get in touch with your AD team and verify if there are any changes applied to the domain controller and there are no network issues.
    Also since this is a multi domain, make sure you have 2 way transitive forest trust as mentioned in SAP Note : 1323391 and FQDN for Directory servers are maintained in registry as per 1199995
    http://service.sap.com/sap/support/notes/1323391
    http://service.sap.com/sap/support/notes/1199995
    -Ambarish-

  • User Authentication Failed error when trying to display a JSP portlet

    The steps carried out are as follows :
    1. Created a JSP file named "c.jsp" and deployed it under 902_MidTier_Home\j2ee\home\default-web-app\examples\jsp
    2. Created a table named USER_TABLE under Scott schema to store the usernames and passwords to validate this JSP application.
    3. Registered this JSP as an external application with the following values :
    Application Name           : RAGHU
    Login URL          : http://hostname:port/j2ee/examples/jsp/c.jsp
    User Name/ID Field Name     : username
    Password Field Name     : password
    Type of Authentication Used : POST
    3. Clicked on the External Application and entered the username as USER1 and password as USER1 ( These values are available
    under USER_TABLE for comparison ). Then it shows the message "Hi User1 .. Welcome message"
    4. Now created a directory named JSPSAMPLE under "WEB-INF\Providers" and put the provider.xml file under this.
    Created a raghu.properties file and placed it under "WEB-INF\deployment".
    5. Now tested the testpage using the URL " http://hostname:port/jpdk/providers/raghu " and it works fine.
    6. Registered this as a provider in Portal and added this portlet onto a page. Assigned this page to a newly created user.
    It gives the message " Authentication Failed - Update Login Information " which is expected. I click on the link and
    it takes me to the external application username password. I enter the credentials but this time it comes back again
    to the page with the same message " Authentication Failed - Update Login Information ".
    7. Basically the values are not passed to the Username and Password in jsp page which is why the problem occurs.
    The JSP Code used is as follows :
    <%@ page import="java.sql.*" %>
    <HTML>
    <HEAD><TITLE>DB Connectivity test</TITLE></HEAD>
    <BODY BGCOLOR="#FFFFFF">
    <CENTER>
    <B>user_table</B>
    <BR><BR>
    <%
    String username = request.getParameter("username");
    String password = request.getParameter("password");
    Connection conn = null;
    try
    Class.forName("oracle.jdbc.driver.OracleDriver");
    conn = DriverManager.getConnection("jdbc:oracle:thin:@hostname:1521:iasdb","scott","tiger");
    Statement stmt = conn.createStatement();
    String query = "SELECT * FROM user_table where userid= '"+ username +"' and passwd = '" + password + "' " ;
    ResultSet rs = stmt.executeQuery(query);
    while(rs.next())
    out.println("<TR>");
    out.println(" <TD> hi " + rs.getString("userid") + ", welcome</TD>");
    out.println("</TR>");
    out.println("</TABLE>");
    catch(SQLException e)
    out.println("SQLException: " + e.getMessage() + "<BR>");
    while((e = e.getNextException()) != null)
    out.println(e.getMessage() + "<BR>");
    out.println("invalid userid,password");
    catch(ClassNotFoundException e)
    out.println("ClassNotFoundException: " + e.getMessage() + "<BR>");
    finally
    //Clean up resources, close the connection.
    if(conn != null)
    try
    conn.close();
    catch (Exception ignored) {}
    %>
    </CENTER>
    </BODY>
    </HTML>
    The Provider.xml file used is as follows :
    <?xml version="1.0" encoding="UTF-8"?>
    <?providerDefinition version="3.1"?>
    <provider class="oracle.portal.provider.v2.http.URLProviderDefinition">
         <providerInstanceClass>oracle.portal.provider.v2.http.URLProviderInstance</providerInstanceClass>
         <session>true</session>
         <authentication class="oracle.portal.provider.v2.security.Authentication">
              <authType>ExternalApp</authType>
              <userFieldName>username</userFieldName>
              <userPwdName>password</userPwdName>
              <errorPageMessages>Raghu,Please sign in,Sign me up!</errorPageMessages>
         </authentication>
         <portlet class="oracle.portal.provider.v2.http.URLPortletDefinition">
              <id>1</id>
              <name>RaghuPortlet</name>
              <title>Raghu Mail Portlet</title>
              <description>This portlet is to test Integration services using mail.yahoo.com</description>
              <timeout>100</timeout>
              <timeoutMessage>Raghu timed out</timeoutMessage>
              <showEdit>false</showEdit>
              <showEditDefault>false</showEditDefault>
              <showPreview>false</showPreview>
              <showDetails>false</showDetails>
              <hasHelp>false</hasHelp>
              <hasAbout>false</hasAbout>
              <acceptContentType>text/html</acceptContentType>
              <registrationPortlet>false</registrationPortlet>
              <accessControl>public</accessControl>
              <renderer class="oracle.portal.provider.v2.render.RenderManager">
                   <showPage class="oracle.portal.provider.v2.render.http.URLRenderer">
                        <pageUrl>http://172.17.24.235:8888/c.jsp</pageUrl>
                        <contentType>text/html</contentType>
                        <filter class="oracle.portal.provider.v2.render.HtmlFilter">
                             <useAuthLinks>true</useAuthLinks>
                             <headerTrimTag>&lt;table width="100%" cellpadding=0 cellspacing=0 border=0>&lt;tr>&lt;td bgcolor=#9bbad6></headerTrimTag>
                             <footerTrimTag>&lt;table width="100%" cellpadding=2 cellspacing=1>&lt;tr>&lt;td bgcolor=#9bbad6></footerTrimTag>
                             <convertTarget>true</convertTarget>
                             <redirectUrlFieldName>.done</redirectUrlFieldName>
                        </filter>
                   </showPage>
              </renderer>
              <securityManager class="oracle.portal.provider.v2.security.URLSecurityManager">
                   <authorizType>registered</authorizType>
              </securityManager>
         </portlet>
    </provider>
    The Contents of raghu.properties file
    serviceClass=oracle.webdb.provider.v2.adapter.soapV1.ProviderAdapter
    loaderClass=oracle.portal.provider.v2.http.DefaultProviderLoader
    showTestPage=true
    definition=providers/raghu/provider.xml
    autoReload=true
    Any inputs regarding why the values are passed properly in case of External Application but not so when registered as
    a portlet in Portal.
    Regards
    Satish G

    As I can see from the information posted, you are trying to
    use URL-based portlet's SSO feature, though not in a correct
    way.
    The SSO feature of URL-based portlets relie on the usage
    of Cookies as authentication tokens. For example, in the
    present context, http://hostname:port/j2ee/examples/jsp/c.jsp
    will write a cookie to the client upon successfull authentication.
    Subsequent access to the same JSP or some other JSP in the same
    workspace should be checking for the existence of this particular
    cookie at the client side and if found should not prompt for
    user information again.
    If you can fine tune your existing applications as per above
    conditions, then everything should work fine. Else you might
    want to use page parameters to pass user information.
    For more information on page parameters, please visit
    http://portalstudio.oracle.com/servlet/page?_pageid=350&_dad=ops&_schema=OPSTUDIO&12678_PDKHOME902_39847486.p_subid=249821&12678_PDKHOME902_39847486.p_sub_siteid=73&12678_PDKHOME902_39847486.p_edit=0#NEW1

  • Tacacs authentication fails for one user account for only one switch

    Hi,
    I am having an scenario, where as Tacacs authentication fails for one user account for only one switch.
    The same user account works well for other devices.
    The AAA configs are same on every devices in the network.
    Heres the show tacacs output from the switch where only one user account fails;
                  Socket opens:        157
                 Socket closes:        156
                 Socket aborts:        303
                 Socket errors:          1
               Socket Timeouts:          2
       Failed Connect Attempts:          0
            Total Packets Sent:       1703
            Total Packets Recv:       1243
              Expected Replies:          0
    What could be the reason ?
    No errors on ACS server; same rights had been given to the user account.
    Thanks to advise.
    Prasey

    Hi there,
    Does the user get authenticated in the ACS logs?
    reports and activity----> failed attempts
    ro
    reports and activity----->  passed authentications
    That will help narrow it down.
    Brad

  • I keep getting a notification that says "Google Talk authentication failed"...does anyone know how to get rid of this?  I tried looking for it in the apps but not really sure what google talk is or how to get rid of this message that keeps popping up.

    How do i get rid of the message that keeps popping up that says "google talk authentication failed"????

    funwidowlady,
    Good afternoon!  I'm glad I can be here to help with this error. In the device this application is identified only as 'Talk', so that be more familiar to you. First I recommend opening the 'Market' app on your phone, then Menu>My Apps to see if this application requires an update. It will display a list on top of all applications that need to be updated. If nothing exists, tap 'Home' and go into 'Settings>Applications>Manage Applications>Talk, then tap 'Clear Cache' and 'Clear Data' to remove the history of that application and stop the notifications.  The app will remain on your phone for future use, if you desire to take advantage of it. Read more about Google Talk here
    Thank you!
    AdamE_VZW
    Follow us on Twitter @VZWSupport

  • "Ticket authentication failed" error in Principal Propagation scenario

    Hi All,
    I am working on Principal Propagation, where the scenario is sync RFC-PI-RFC. I have followed all steps mentioned in the below blog. When I execute the scenario (with Principal propagation box checked in the sender agreement) I get dump while executing the RFC from sender system. The dump is:
    "Ticket authentication failed"
    Scenario works fine if I don't check Principal propagation check box in the sender agreement.
    Principal Propagation blog: /people/alexander.bundschuh/blog/2007/01/16/principal-propagation-in-sap-xi
    Can anyone suggest what can be the reason for this dump?
    Thanks,
    Shweta.

    Hi All,
    Any inputs on this?
    Thanks,
    Shweta.

  • Error while saving Report output-Authentication failed

    Hi All,
    For the client system there is a customization report with output of html format. it can't display all with the error message
    unable to open the internet site. http://<site:port>/OA_CGI/FNDWRR.exe?temp_id=<temp_id>*
    operation aborted*
    if user choose to "save as" , it will back with error message
    Authentication failed*
    Can anyone here give me some guide?
    Best Regards,
    Chelsea

    Refer Note 184154.1
    Regards,
    Srini

  • TS4002 Can you tell me if the smtp settings have changed recently?  I use me/ICloud mail with Outlook and can not receive emails but outgoing emails are no longer working.  Error message is: Authentication failed because Outlook doesn't support any of the

    I am able to receive messages on my IMac using Outlook but am unable to send.  I've had no trouble in the past but began receiving the following messages today.
    5.7.8 Bad username or password (Authentication failed).
    Authentication failed because Outlook doesn't support any of the available authentication methods.
    I am able to send messages using this account on my IPhone and IPad so the IMac is the only place I am having issues.  Any advice?

    Here are the correct settings. They have never changed since iCloud debuted a year ago.
    Server information
    IMAP (Incoming Mail Server) information:
    Server name: imap.mail.me.com
    SSL Required: Yes
    Port: 993
    Username: [email protected] (use your @me.com address from your iCloud account)
    Password: Your iCloud password
    SMTP (outgoing mail server) information:
    Server name: smtp.mail.me.com
    SSL Required: Yes
    Port: 587
    SMTP Authentication Required: Yes
    Username: [email protected] (use your @me.com address from your iCloud account)
    Password: Your iCloud password
    Note: If you receive errors using SSL, try using TLS instead. SSL is required for both IMAP and SMTP connection with iCloud. POP is not supported by iCloud. 

  • 802.1x authentication fail

    i have a juniper device linux operating system on that we have radius server configured and i am trying to integrate my WLC with that radius
    i have added WLC as a host there in radius
    on wlc i have configured authentication like radius ip shared secret key and done
    its working i can ping radius server
    also in wlc i configured on Wlan aaa allow override check box and also hited the WPA2 802.1x layer2 security and radius server option brought on top.
    i also configured my windows wireless adaptor as PEAP MSCHAP v2
    i am trying to connect this ssid and its asking for my AD accounts but when i enter that its not authenticating users and giving this logs.
    (WiSM-slot24-1) >debug aaa events enable
    (WiSM-slot24-1) >
    (WiSM-slot24-1) >
    (WiSM-slot24-1) >*apfMsConnTask_0: Dec 31 15:12:03.043: 00:13:e8:3e:26:bf Processing RSN IE type 48, length 22 for mobile 00:13:e8:3e:26:bf
    *apfMsConnTask_0: Dec 31 15:12:03.043: 00:13:e8:3e:26:bf Received RSN IE with 0 PMKIDs from mobile 00:13:e8:3e:26:bf
    *apfMsConnTask_0: Dec 31 15:12:03.043: 00:13:e8:3e:26:bf apfMsAssoStateInc
    *dot1xMsgTask: Dec 31 15:12:03.044: 00:13:e8:3e:26:bf Station 00:13:e8:3e:26:bf setting dot1x reauth timeout = 1800
    *dot1xMsgTask: Dec 31 15:12:03.044: 00:13:e8:3e:26:bf Sending EAP-Request/Identity to mobile 00:13:e8:3e:26:bf (EAP Id 1)
    *Dot1x_NW_MsgTask_0: Dec 31 15:12:03.097: 00:13:e8:3e:26:bf Received EAPOL START from mobile 00:13:e8:3e:26:bf
    *Dot1x_NW_MsgTask_0: Dec 31 15:12:03.097: 00:13:e8:3e:26:bf Sending EAP-Request/Identity to mobile 00:13:e8:3e:26:bf (EAP Id 2)
    *Dot1x_NW_MsgTask_0: Dec 31 15:12:12.596: 00:13:e8:3e:26:bf Received EAPOL EAPPKT from mobile 00:13:e8:3e:26:bf
    *Dot1x_NW_MsgTask_0: Dec 31 15:12:12.596: 00:13:e8:3e:26:bf Received Identity Response (count=2) from mobile 00:13:e8:3e:26:bf
    *Dot1x_NW_MsgTask_0: Dec 31 15:12:12.596: 00:13:e8:3e:26:bf Audit Session ID added to the mscb: 0a8740e10000002e4efefc1c
    *Dot1x_NW_MsgTask_0: Dec 31 15:12:12.596: Creating audit session ID (dot1x_aaa_eapresp_supp) and Radius Request
    *aaaQueueReader: Dec 31 15:12:12.597: apfVapRadiusInfoGet: WLAN(1) dynamic int attributes srcAddr:0x0, gw:0x0, mask:0x0, vlan:0, dpPort:0, srcPort:0
    *aaaQueueReader: Dec 31 15:12:12.597: 00:13:e8:3e:26:bf Successful transmission of Authentication Packet (id 202) to 10.34.11.2:1812, proxy state 00:13:e8:3e:26:bf-00:00
    *radiusTransportThread: Dec 31 15:12:12.598: ****Enter processIncomingMessages: response code=11
    *radiusTransportThread: Dec 31 15:12:12.598: ****Enter processRadiusResponse: response code=11
    *radiusTransportThread: Dec 31 15:12:12.598: 00:13:e8:3e:26:bf Access-Challenge received from RADIUS server 10.34.11.2 for mobile 00:13:e8:3e:26:bf receiveId = 3
    *Dot1x_NW_MsgTask_0: Dec 31 15:12:12.598: 00:13:e8:3e:26:bf Processing Access-Challenge for mobile 00:13:e8:3e:26:bf
    *Dot1x_NW_MsgTask_0: Dec 31 15:12:12.598: 00:13:e8:3e:26:bf Sending EAP Request from AAA to mobile 00:13:e8:3e:26:bf (EAP Id 3)
    *Dot1x_NW_MsgTask_0: Dec 31 15:12:12.600: 00:13:e8:3e:26:bf Received EAPOL EAPPKT from mobile 00:13:e8:3e:26:bf
    *Dot1x_NW_MsgTask_0: Dec 31 15:12:12.600: 00:13:e8:3e:26:bf Received EAP Response from mobile 00:13:e8:3e:26:bf (EAP Id 3, EAP Type 3)
    *aaaQueueReader: Dec 31 15:12:12.600: apfVapRadiusInfoGet: WLAN(1) dynamic int attributes srcAddr:0x0, gw:0x0, mask:0x0, vlan:0, dpPort:0, srcPort:0
    *aaaQueueReader: Dec 31 15:12:12.600: 00:13:e8:3e:26:bf Successful transmission of Authentication Packet (id 203) to 10.34.11.2:1812, proxy state 00:13:e8:3e:26:bf-00:00
    *radiusTransportThread: Dec 31 15:12:12.601: ****Enter processIncomingMessages: response code=3
    *radiusTransportThread: Dec 31 15:12:12.601: ****Enter processRadiusResponse: response code=3
    *radiusTransportThread: Dec 31 15:12:12.601: 00:13:e8:3e:26:bf Access-Reject received from RADIUS server 10.34.11.2 for mobile 00:13:e8:3e:26:bf receiveId = 3
    *radiusTransportThread: Dec 31 15:12:12.601: 00:13:e8:3e:26:bf [Error] Client requested no retries for mobile 00:13:E8:3E:26:BF
    *radiusTransportThread: Dec 31 15:12:12.601: 00:13:e8:3e:26:bf Returning AAA Error 'Authentication Failed' (-4) for mobile 00:13:e8:3e:26:bf
    *Dot1x_NW_MsgTask_0: Dec 31 15:12:12.601: 00:13:e8:3e:26:bf Processing Access-Reject for mobile 00:13:e8:3e:26:bf
    *Dot1x_NW_MsgTask_0: Dec 31 15:12:12.602: 00:13:e8:3e:26:bf Removing PMK cache due to EAP-Failure for mobile 00:13:e8:3e:26:bf (EAP Id 3)
    *Dot1x_NW_MsgTask_0: Dec 31 15:12:12.602: 00:13:e8:3e:26:bf Sending EAP-Failure to mobile 00:13:e8:3e:26:bf (EAP Id 3)
    *Dot1x_NW_MsgTask_0: Dec 31 15:12:12.602: 00:13:e8:3e:26:bf Setting quiet timer for 5 seconds for mobile 00:13:e8:3e:26:bf
    *apfMsConnTask_0: Dec 31 15:12:15.319: 00:13:e8:3e:26:bf Processing RSN IE type 48, length 22 for mobile 00:13:e8:3e:26:bf
    *apfMsConnTask_0: Dec 31 15:12:15.319: 00:13:e8:3e:26:bf Received RSN IE with 0 PMKIDs from mobile 00:13:e8:3e:26:bf
    *dot1xMsgTask: Dec 31 15:12:15.320: 00:13:e8:3e:26:bf Sending EAP-Request/Identity to mobile 00:13:e8:3e:26:bf (EAP Id 1)
    *Dot1x_NW_MsgTask_0: Dec 31 15:12:15.389: 00:13:e8:3e:26:bf Received EAPOL START from mobile 00:13:e8:3e:26:bf
    *Dot1x_NW_MsgTask_0: Dec 31 15:12:15.389: 00:13:e8:3e:26:bf Sending EAP-Request/Identity to mobile 00:13:e8:3e:26:bf (EAP Id 2)
    any idea to solve this problem?
    or any one knows that how to configur a radius server on juniper linux operating system?
    many thanks in advance

    You should post on the Juniper forums regarding your policy configuration.  You should stick with using a radius than just doing ldap through the wlc.  Here is a link for webauth using ldap, but should get you close.  Again... you should look at getting your juniper radius configuration fixed first.
    http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a0080a03e09.shtml

  • ERROR: Ldap Authentication failed for dap during installation of iAS 6.0 SP3

    I am attempting to install ias Enterprise Edition (6.0 SP3) on solaris 2.8 using typical in basesetup. I am trying to install new Directory server as I don't have an existing one.
    During the installation I got the following error.
    ERROR: Ldap Authentication failed for url ldap://hostname:389/o=NetScape Root user id admin (151: Unknown Error)
    Fatal Slapd did not add Directory server information to config Server.
    Warning slapd could'nt populate with ldif file Yes error code 151.
    ERROR:Failure installing iPlanet Directory Server.
    Do you want to continue: ( I entered yes )
    Configuring Administration Server Segmentation fault core dumped.
    Error: Failure installing Netscape Administration Server.
    Do you want to continue:( I responded with yes).
    And during the Extraction I got the following
    ERROR:mple_bind: Can't connect to the LDAP server - No route to host
    ERROR: Unable to connect to LDAP Directory Server
    Hostname: hostname
    Port: 389
    User: cn=Directory Manager
    Password: <password-for-cn=Directory Manager
    Please make sure this Directory Server is currently running.
    You might need to run 'stop-slapd' and then
    'start-slapd' in the Directory Server home directory, in order to restart
    LDAP. When finished, press ENTER to continue, or S to skip this step:
    Start registering Bootstrap EJB...
    javax.naming.NameNotFoundException
    at java.lang.Throwable.fillInStackTrace(Native Method)
    at java.lang.Throwable.fillInStackTrace(Compiled Code)
    at java.lang.Throwable.<init>(Compiled Code)
    at java.lang.Exception.<init>(Compiled > Code)
    at javax.naming.NamingException.<init>(NamingException.java:114)
    at javax.naming.NameNotFoundException.<init>(NameNotFoundException.java: 48)
    at com.netscape.server.jndi.RootContext.resolveCtx(Unknown Source)
    "ldaperror" 76 lines, 2944 characters
    at com.netscape.server.jndi.RootContext.resolveCtx(Unknown Source)
    at com.netscape.server.jndi.RootContext.bind(Unknown Source)
    at com.netscape.server.jndi.RootContext.bind(Unknown Source)
    at javax.naming.InitialContext.bind(InitialContext.java:371)
    at com.netscape.server.deployment.EjbReg.deployToNaming(Unknown Source)
    at com.netscape.server.deployment.EjbReg.registerEjbJar(Compiled Code)
    at com.netscape.server.deployment.EjbReg.registerEjbJar(Compiled Code)
    at com.netscape.server.deployment.EjbReg.run(Compiled Code)
    at com.netscape.server.deployment.EjbReg.main(Unknown Source)
    Start registering iAS 60 Fortune Application...
    Start iPlanet Application Server
    Start iPlanet Application Server
    Start Web Server iPlanet-WebServer-Enterprise/6.0SP1 B08/20/200100:58
    warning: daemon is running as super-user
    [LS ls1] http://gedemo1.plateau.com, port 80 ready
    to accept requests
    startup: server started successfully.
    After completion of installation, I tried to start the console. But I got the following error;
    "Cant connect ot the admin server. The url is not correct or the server is not running.
    Finally,when I started the admintool(iASTT),it shows the iAS1
    was registered( marked with a red cross mark) and says "cant login. make sure the user
    name & passwdord are correct" when i click on it.
    Thanks in advance for any help
    Madhavi

    Hi,
    Make sure that the directory server is installed first. If it is running
    ok, then you can try adding an admin user, please check the following
    technote.
    http://knowledgebase.iplanet.com/ikb/kb/articles/4106.html
    regards
    Swami
    madhavi korupolu wrote:
    I am attempting to install ias Enterprise Edition (6.0 SP3) on
    solaris 2.8 using typical in basesetup. I am trying to install new
    Directory server as I don't have an existing one.
    During the installation I got the following error.
    ERROR: Ldap Authentication failed for url
    ldap://hostname:389/o=NetScape Root user id admin (151: Unknown
    Error)
    Fatal Slapd did not add Directory server information to config
    Server.
    Warning slapd could'nt populate with ldif file Yes error code 151.
    ERROR:Failure installing iPlanet Directory Server.
    Do you want to continue: ( I entered yes )
    Configuring Administration Server Segmentation fault core dumped.
    Error: Failure installing Netscape Administration Server.
    Do you want to continue:( I responded with yes).
    And during the Extraction I got the following
    ERROR:mple_bind: Can't connect to the LDAP server - No route to host
    ERROR: Unable to connect to LDAP Directory Server
    Hostname: hostname
    Port: 389
    User: cn=Directory Manager
    Password: <password-for-cn=Directory Manager
    Please make sure this Directory Server is currently running.
    You might need to run 'stop-slapd' and then
    'start-slapd' in the Directory Server home directory, in order to
    restart
    LDAP. When finished, press ENTER to continue, or S to skip this
    step:
    Start registering Bootstrap EJB...
    javax.naming.NameNotFoundException
    at java.lang.Throwable.fillInStackTrace(Native Method)
    at java.lang.Throwable.fillInStackTrace(Compiled Code)
    at java.lang.Throwable.<init>(Compiled Code)
    at java.lang.Exception.<init>(Compiled > Code)
    at javax.naming.NamingException.<init>(NamingException.java:114)
    at
    javax.naming.NameNotFoundException.<init>(NameNotFoundException.java:
    48)
    at com.netscape.server.jndi.RootContext.resolveCtx(Unknown Source)
    "ldaperror" 76 lines, 2944 characters
    at com.netscape.server.jndi.RootContext.resolveCtx(Unknown Source)
    at com.netscape.server.jndi.RootContext.bind(Unknown Source)
    at com.netscape.server.jndi.RootContext.bind(Unknown Source)
    at javax.naming.InitialContext.bind(InitialContext.java:371)
    at com.netscape.server.deployment.EjbReg.deployToNaming(Unknown
    Source)
    at com.netscape.server.deployment.EjbReg.registerEjbJar(Compiled
    Code)
    at com.netscape.server.deployment.EjbReg.registerEjbJar(Compiled
    Code)
    at com.netscape.server.deployment.EjbReg.run(Compiled Code)
    at com.netscape.server.deployment.EjbReg.main(Unknown Source)
    Start registering iAS 60 Fortune Application...
    Start iPlanet Application Server
    Start iPlanet Application Server
    Start Web Server iPlanet-WebServer-Enterprise/6.0SP1 B08/20/200100:58
    warning: daemon is running as super-user
    [LS ls1] http://gedemo1.plateau.com, port 80 ready
    to accept requests
    startup: server started successfully.
    After completion of installation, I tried to start the console. But I
    got the following error;
    "Cant connect ot the admin server. The url is not correct or the
    server is not running.
    Finally,when I started the admintool(iASTT),it shows the iAS1
    was registered( marked with a red cross mark) and says "cant login.
    make sure the user
    name & passwdord are correct" when i click on it.
    Thanks in advance for any help
    Madhavi
    Try our New Web Based Forum at http://softwareforum.sun.com
    Includes Access to our Product Knowledge Base!

  • MIC not verified # authentication-failed

    Hi,
    We are getting this error while trying to send messages from XI through AS2:
    MIC not verified # authentication-failed
    Can anybody please let us know the reason for this error.
    Thanks in advance.
    Best Regards,
    Shweta

    Hi Shabarish & Prateek,
    Thanks a lot for the information.
    I've also checked this information in Seeburger document and I agree this can be an issue with the Certificate.
    But these scenarios were working fine for a long time,the Certificates are valid till 2016.
    And the most important thing is,we get this error in 1 message out of 100-200,other messages are sent successfully.
    So,if this is an issue with certificate,how is it possible that it affects only 1-2 messages not all.
    I had never seen this error before and suddenly we have started getting such errors for a number of scenarios for last 15 days.
    I believe ,there can be a problem with Certificate for 1 customer but if it is more than one ,it is hard to believe that all of them have problems with Certificates and at the same time.
    I tried to search for notes related to this problem.
    Is it something related to MIME content,as mentioned in note 1287778?
    Kindly let me know.
    Thanks.
    Regards,
    Shweta

  • 802.1x port authentication failing after getting a access-accept packet

    Hi all,
    Im not 100% sure what the hell is going on here.
    Any idea's or help will be appreciated.
    Heres the topology.
    1 x windows 2012 NPS
    1x 3750X
    1x Windows 7 x64
    data flow
    <laptop> - - [gi 1/0/13]<3750X>[gi 1/0/48]- -[gi 5/39]<6513>[po 1] - - [po 4]<6509><5/1> - - <VMWARE>[NPS Server]
    The switch that is doing the authentication is the 3750X. Here is the IOS version.
    Switch Ports Model              SW Version            SW Image
    *    1 54    WS-C3750X-48       15.2(1)E              C3750E-UNIVERSALK9-M
    A wireshark trace on the NPS server shows that the packets are arriving and being sent back
    Wireshark on a mirror of the trunk port connecting the 6513. It also shows packets being sent and arriving. access-accept packets are being recieved.
    As you can see in the debug output, the switch is getting a access-accept, then it is stating a AAA failure.
    here is a debug output as you plug in the laptop.
    Oct 24 10:53:44.653: dot1x-ev:[Gi1/0/13] Interface state changed to DOWN
    Oct 24 10:53:44.653: dot1x-ev:[Gi1/0/13] No DOT1X subblock found for port down
    Oct 24 10:53:45.643: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down
    Oct 24 10:53:46.641: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down
    Oct 24 10:53:47.538: dot1x-ev:[Gi1/0/13] Interface state changed to UP
    Oct 24 10:53:47.564: dot1x-packet:[6431.500e.9b00, Gi1/0/13] queuing an EAPOL pkt on Auth Q
    Oct 24 10:53:47.572: dot1x-ev:DOT1X Supplicant not enabled on GigabitEthernet1/0/13
    Oct 24 10:53:47.572: dot1x-packet:EAPOL pak rx - Ver: 0x1  type: 0x1
    Oct 24 10:53:47.572: dot1x-packet: length: 0x0000
    Oct 24 10:53:47.572: dot1x-ev:[Gi1/0/13] Dequeued pkt: Int Gi1/0/13 CODE= 0,TYPE= 0,LEN= 0
    Oct 24 10:53:47.572: dot1x-ev:[Gi1/0/13] Received pkt saddr =6431.500e.9b00 , daddr = 0180.c200.0003, pae-ether-type = 888e.0101.0000
    Oct 24 10:53:47.572: dot1x-ev:[Gi1/0/13] Couldn't find the supplicant in the list
    Oct 24 10:53:47.572: dot1x-ev:[6431.500e.9b00, Gi1/0/13] New client detected, sending session start event for 6431.500e.9b00
    Oct 24 10:53:47.572: AAA/BIND(00000047): Bind i/f
    Oct 24 10:53:47.580: dot1x-ev:[6431.500e.9b00, Gi1/0/13] Sending create new context event to EAP for 0x15000045 (6431.500e.9b00)
    Oct 24 10:53:47.580: EAP-EVENT: Received context create from LL (Dot1x-Authenticator) (0x15000045)
    Oct 24 10:53:47.580: EAP-AUTH-EVENT: Received AAA ID 0x00000047 from LL
    Oct 24 10:53:47.580: EAP-AUTH-AAA-EVENT: Assigning AAA ID 0x00000047
    Oct 24 10:53:47.580: EAP-AUTH-AAA-EVENT: CTS not enabled on interface Gi1/0/13
    Oct 24 10:53:47.580: EAP-AUTH-EVENT: Received Session ID "C0A846660000004700DF6030" from LL
    Oct 24 10:53:47.580: EAP-AUTH-EVENT: Setting authentication mode: Passthrough
    Oct 24 10:53:47.580:     eap_authen : initial state eap_auth_initialize has enter
    Oct 24 10:53:47.580: EAP-EVENT: Allocated new EAP context (handle = 0xE8000047)
    Oct 24 10:53:47.580: dot1x-ev:[6431.500e.9b00, Gi1/0/13] Created a client entry (0x15000045)
    Oct 24 10:53:47.580: dot1x-ev:[6431.500e.9b00, Gi1/0/13] Dot1x authentication started for 0x15000045 (6431.500e.9b00)
    Oct 24 10:53:47.580: %AUTHMGR-5-START: Starting 'dot1x' for client (6431.500e.9b00) on Interface Gi1/0/13 AuditSessionID C0A846660000004700DF6030
    Oct 24 10:53:47.580: EAP-EVENT: Received EAP event 'EAP_AUTHENTICATOR_START' on handle 0xE8000047
    Oct 24 10:53:47.580:     eap_authen : during state eap_auth_initialize, got event 25(eapStartTmo)
    Oct 24 10:53:47.580: @@@ eap_authen : eap_auth_initialize -> eap_auth_select_action
    Oct 24 10:53:47.580:     eap_authen : during state eap_auth_select_action, got event 20(eapDecisionPropose)
    Oct 24 10:53:47.580: @@@ eap_authen : eap_auth_select_action -> eap_auth_propose_method
    Oct 24 10:53:47.580:     eap_authen : idle during state eap_auth_propose_method
    Oct 24 10:53:47.580: @@@ eap_authen : eap_auth_propose_method -> eap_auth_method_request
    Oct 24 10:53:47.580:     eap_authen : idle during state eap_auth_method_request
    Oct 24 10:53:47.580: @@@ eap_authen : eap_auth_method_request -> eap_auth_tx_packet
    Oct 24 10:53:47.580: EAP-AUTH-EVENT: Current method = Identity
    Oct 24 10:53:47.580: EAP-EVENT: Sending LL (Dot1x-Authenticator) event 'EAP_CUSTOMIZE_ID_REQUEST' on handle 0xE8000047
    Oct 24 10:53:47.580:     eap_authen : idle during state eap_auth_tx_packet
    Oct 24 10:53:47.580: @@@ eap_authen : eap_auth_tx_packet -> eap_auth_idle
    Oct 24 10:53:47.589: EAP-AUTH-TX-PAK: Code:REQUEST  ID:0x1   Length:0x0005  Type:IDENTITY
    Oct 24 10:53:47.589: EAP-EVENT: Started 'Authenticator ReqId Retransmit' timer (30s) for EAP sesion handle 0xE8000047
    Oct 24 10:53:47.589: EAP-EVENT: Started EAP tick timer
    Oct 24 10:53:47.589: EAP-EVENT: Sending LL (Dot1x-Authenticator) event 'EAP_TX_PACKET' on handle 0xE8000047
    Oct 24 10:53:47.597: dot1x-ev:[Gi1/0/13] Sending EAPOL packet to group PAE address
    Oct 24 10:53:47.597: dot1x-ev:[Gi1/0/13] Sending out EAPOL packet
    Oct 24 10:53:47.597: dot1x-packet:EAPOL pak Tx - Ver: 0x3  type: 0x0
    Oct 24 10:53:47.597: dot1x-packet: length: 0x0005
    Oct 24 10:53:47.597: dot1x-packet:EAP code: 0x1  id: 0x1  length: 0x0005
    Oct 24 10:53:47.597: dot1x-packet: type: 0x1
    Oct 24 10:53:47.597: dot1x-packet:[6431.500e.9b00, Gi1/0/13] EAPOL packet sent to client 0x15000045
    Oct 24 10:53:47.606: dot1x-packet:[6431.500e.9b00, Gi1/0/13] Queuing an EAPOL pkt on Authenticator Q
    Oct 24 10:53:47.606: dot1x-packet:EAPOL pak rx - Ver: 0x1  type: 0x0
    Oct 24 10:53:47.606: dot1x-packet: length: 0x001F
    Oct 24 10:53:47.606: dot1x-ev:[Gi1/0/13] Dequeued pkt: Int Gi1/0/13 CODE= 2,TYPE= 1,LEN= 31
    Oct 24 10:53:47.606: dot1x-ev:[Gi1/0/13] Received pkt saddr =6431.500e.9b00 , daddr = 0180.c200.0003, pae-ether-type = 888e.0100.001f
    Oct 24 10:53:47.606: dot1x-packet:EAPOL pak rx - Ver: 0x1  type: 0x0
    Oct 24 10:53:47.606: dot1x-packet: length: 0x001F
    Oct 24 10:53:47.606: dot1x-ev:[6431.500e.9b00, Gi1/0/13] Response sent to the server from 0x15000045
    Oct 24 10:53:47.606: EAP-EVENT: Received LL (Dot1x-Authenticator) event 'EAP_RX_PACKET' on handle 0xE8000047
    Oct 24 10:53:47.606: EAP-AUTH-RX-PAK: Code:RESPONSE  ID:0x1   Length:0x001F  Type:IDENTITY
    Oct 24 10:53:47.606:     Payload:  47454E4552414C5C72616E64792E636F ...
    Oct 24 10:53:47.606:     eap_authen : during state eap_auth_idle, got event 1(eapRxPacket)
    Oct 24 10:53:47.606: @@@ eap_authen : eap_auth_idle -> eap_auth_received
    Oct 24 10:53:47.606: EAP-AUTH-EVENT: EAP Response received by context 0xE8000047
    Oct 24 10:53:47.606: EAP-AUTH-EVENT: EAP Response type = Identity
    Oct 24 10:53:47.606: EAP-EVENT: Stopping 'Authenticator ReqId Retransmit' timer for EAP sesion handle 0xE8000047
    Oct 24 10:53:47.606:     eap_authen : during state eap_auth_received, got event 10(eapMethodData)
    Oct 24 10:53:47.606: @@@ eap_authen : eap_auth_received -> eap_auth_method_response
    Oct 24 10:53:47.606: EAP-AUTH-EVENT: Received peer identity: GENERAL\randy.coburn.admin
    Oct 24 10:53:47.606: EAP-EVENT: Sending LL (Dot1x-Authenticator) event 'EAP_IDENTITY' on handle 0xE8000047
    Oct 24 10:53:47.606:     eap_authen : during state eap_auth_method_response, got event 13(eapMethodEnd)
    Oct 24 10:53:47.606: @@@ eap_authen : eap_auth_method_response -> eap_auth_select_action
    Oct 24 10:53:47.606:     eap_authen : during state eap_auth_select_action, got event 19(eapDecisionPass)
    Oct 24 10:53:47.606: @@@ eap_authen : eap_auth_select_action -> eap_auth_passthru_init
    Oct 24 10:53:47.606:     eap_authen : during state eap_auth_passthru_init, got event 22(eapPthruIdentity)
    Oct 24 10:53:47.614: @@@ eap_authen : eap_auth_passthru_init -> eap_auth_aaa_req
    Oct 24 10:53:47.614: EAP-EVENT: Sending LL (Dot1x-Authenticator) event 'EAP_GET_PEER_MAC_ADDRESS' on handle 0xE8000047
    Oct 24 10:53:47.614: EAP-AUTH-AAA-EVENT: Adding Audit-Session-ID "C0A846660000004700DF6030" to RADIUS Req
    Oct 24 10:53:47.614: EAP-AUTH-AAA-EVENT: Added Audit-Session-ID
    Oct 24 10:53:47.614: EAP-AUTH-AAA-EVENT: Adding IDB "0x070B90F8" to RADIUS Req
    Oct 24 10:53:47.614: EAP-AUTH-AAA-EVENT: Added IDB
    Oct 24 10:53:47.614: EAP-EVENT: Sending LL (Dot1x-Authenticator) event 'EAP_CUSTOMIZE_AAA_REQUEST' on handle 0xE8000047
    Oct 24 10:53:47.614: EAP-AUTH-AAA-EVENT: eap_auth_aaa_authen_request_shim aaa_service 19, eap aaa_list handle 0, mlist handle 0
    Oct 24 10:53:47.614: AAA/AUTHEN/8021X (00000000): Pick method list 'default'
    Oct 24 10:53:47.614: EAP-AUTH-AAA-EVENT: Request sent successfully
    Oct 24 10:53:47.614:     eap_authen : during state eap_auth_aaa_req, got event 24(eapAAAReqOk)
    Oct 24 10:53:47.614: @@@ eap_authen : eap_auth_aaa_req -> eap_auth_aaa_idle
    Oct 24 10:53:47.614: RADIUS/ENCODE(00000000):Orig. component type = Invalid
    Oct 24 10:53:47.614: RADIUS/ENCODE(00000000): Unsupported AAA attribute hwidb
    Oct 24 10:53:47.614: RADIUS/ENCODE(00000000): Unsupported AAA attribute aaa-authen-type
    Oct 24 10:53:47.614: RADIUS/ENCODE(00000000): Unsupported AAA attribute aaa-authen-service
    Oct 24 10:53:47.614: RADIUS/ENCODE(00000000): Unsupported AAA attribute clid-mac-addr
    Oct 24 10:53:47.614: RADIUS/ENCODE(00000000): Unsupported AAA attribute target-scope
    Oct 24 10:53:47.614: RADIUS/ENCODE(00000000): Unsupported AAA attribute aaa-unique-id
    Oct 24 10:53:47.614: RADIUS(00000000): Config NAS IP: 0.0.0.0
    Oct 24 10:53:47.614: RADIUS(00000000): sending
    Oct 24 10:53:47.614: RADIUS/ENCODE: Best Local IP-Address 192.168.70.102 for Radius-Server 192.168.19.121
    Oct 24 10:53:47.614: RADIUS(00000000): Send Access-Request to 192.168.19.121:1645 id 1645/21, len 288
    Oct 24 10:53:47.614: RADIUS:  authenticator F1 BA E5 31 71 54 BF 1A - A2 B1 5E 1A 63 72 1E 72
    Oct 24 10:53:47.614: RADIUS:  User-Name           [1]   28  "GENERAL\randy.coburn.admin"
    Oct 24 10:53:47.614: RADIUS:  Service-Type        [6]   6   Framed                    [2]
    Oct 24 10:53:47.614: RADIUS:  Vendor, Cisco       [26]  27
    Oct 24 10:53:47.614: RADIUS:   Cisco AVpair       [1]   21  "service-type=Framed"
    Oct 24 10:53:47.614: RADIUS:  Framed-MTU          [12]  6   1500
    Oct 24 10:53:47.614: RADIUS:  Called-Station-Id   [30]  19  "AC-F2-C5-75-7D-0D"
    Oct 24 10:53:47.614: RADIUS:  Calling-Station-Id  [31]  19  "64-31-50-0E-9B-00"
    Oct 24 10:53:47.614: RADIUS:  EAP-Message         [79]  33
    Oct 24 10:53:47.614: RADIUS:   02 01 00 1F 01 47 45 4E 45 52 41 4C 5C 72 61 6E 64 79 2E 63 6F  [GENERAL\randy.co]
    Oct 24 10:53:47.622: RADIUS:   62 75 72 6E 2E 61 64 6D 69 6E        [ burn.admin]
    Oct 24 10:53:47.622: RADIUS:  Message-Authenticato[80]  18
    Oct 24 10:53:47.622: RADIUS:   EE 52 4D ED B9 06 F3 CE 63 AC 9D 73 24 1B A7 ED             [ RMcs$]
    Oct 24 10:53:47.622: RADIUS:  EAP-Key-Name        [102] 2   *
    Oct 24 10:53:47.622: RADIUS:  Vendor, Cisco       [26]  49
    Oct 24 10:53:47.622: RADIUS:   Cisco AVpair       [1]   43  "audit-session-id=C0A846660000004700DF6030"
    Oct 24 10:53:47.622: RADIUS:  Vendor, Cisco       [26]  20
    Oct 24 10:53:47.622: RADIUS:   Cisco AVpair       [1]   14  "method=dot1x"
    Oct 24 10:53:47.622: RADIUS:  NAS-IP-Address      [4]   6   192.168.70.102
    Oct 24 10:53:47.622: RADIUS:  NAS-Port            [5]   6   60000
    Oct 24 10:53:47.622: RADIUS:  NAS-Port-Id         [87]  23  "GigabitEthernet1/0/13"
    Oct 24 10:53:47.622: RADIUS:  NAS-Port-Type       [61]  6   Ethernet                  [15]
    Oct 24 10:53:47.622: RADIUS(00000000): Sending a IPv4 Radius Packet
    Oct 24 10:53:47.622: RADIUS(00000000): Started 10 sec timeout
    Oct 24 10:53:47.622: RADIUS: Received from id 1645/21 192.168.19.121:1645, Access-Accept, len 66
    Oct 24 10:53:47.622: RADIUS:  authenticator 92 F6 07 AF C1 AB 0B 4C - 1D 9E A0 D1 01 36 27 26
    Oct 24 10:53:47.622: RADIUS:  Class               [25]  46
    Oct 24 10:53:47.622: RADIUS:   76 E3 06 66 00 00 01 37 00 01 02 00 C0 A8 13 79 00 00 00 00 00 00 00 00 00 00 00 00 01 CE CF F8 1F 7B 75 41 00 00 00 00 00 00 00 50          [ vf7y{uAP]
    Oct 24 10:53:47.622: RADIUS(00000000): Received from id 1645/21
    Oct 24 10:53:47.622: EAP-EVENT: eap_aaa_reply
    Oct 24 10:53:47.622: EAP-AUTH-AAA-EVENT: Reply received session_label 72000033
    Oct 24 10:53:47.622: EAP-EVENT: Received AAA event 'EAP_AAA_FAIL' on handle 0xE8000047
    Oct 24 10:53:47.622:     eap_authen : during state eap_auth_aaa_idle, got event 8(eapAAAFail)
    Oct 24 10:53:47.622: @@@ eap_authen : eap_auth_aaa_idle -> eap_auth_failure
    Oct 24 10:53:47.631: EAP-EVENT: Received get canned status from lower layer (0xE8000047)
    Oct 24 10:53:47.631: EAP-AUTH-TX-PAK: Code:FAILURE  ID:0x1   Length:0x0004
    Oct 24 10:53:47.631: EAP-AUTH-EVENT: FAIL for EAP method ID: 1, name: , on handle 0xE8000047
    Oct 24 10:53:47.631: EAP-EVENT: Sending LL (Dot1x-Authenticator) event 'EAP_FAIL' on handle 0xE8000047
    Oct 24 10:53:47.631: dot1x-ev:[6431.500e.9b00, Gi1/0/13] Received an EAP Fail
    Oct 24 10:53:47.639: %DOT1X-5-FAIL: Authentication failed for client (6431.500e.9b00) on Interface Gi1/0/13 AuditSessionID C0A846660000004700DF6030
    Oct 24 10:53:47.639: dot1x-packet:[6431.500e.9b00, Gi1/0/13] Added username in dot1x
    Oct 24 10:53:47.639: dot1x-packet:[6431.500e.9b00, Gi1/0/13] Dot1x did not receive any key data
    Oct 24 10:53:47.639: dot1x-ev:[6431.500e.9b00, Gi1/0/13] Processing client delete for hdl 0x15000045 sent by Auth Mgr
    Oct 24 10:53:47.639: dot1x-ev:[6431.500e.9b00, Gi1/0/13] 6431.500e.9b00: sending canned failure due to method termination
    Oct 24 10:53:47.639: EAP-EVENT: Received get canned status from lower layer (0xE8000047)
    Oct 24 10:53:47.639: dot1x-ev:[Gi1/0/13] Sending EAPOL packet to group PAE address
    Oct 24 10:53:47.639: dot1x-ev:[Gi1/0/13] Sending out EAPOL packet
    Oct 24 10:53:47.639: dot1x-packet:EAPOL pak Tx - Ver: 0x3  type: 0x0
    Oct 24 10:53:47.639: dot1x-packet: length: 0x0004
    Oct 24 10:53:47.639: dot1x-packet:EAP code: 0x4  id: 0x1  length: 0x0004
    Oct 24 10:53:47.639: dot1x-packet:[6431.500e.9b00, Gi1/0/13] EAPOL canned status packet sent to client 0x15000045
    Oct 24 10:53:47.639: dot1x-ev:[6431.500e.9b00, Gi1/0/13] Deleting client 0x15000045 (6431.500e.9b00)
    Oct 24 10:53:47.639: %AUTHMGR-7-STOPPING: Stopping 'dot1x' for client 6431.500e.9b00 on Interface Gi1/0/13 AuditSessionID C0A846660000004700DF6030
    Oct 24 10:53:47.639: %AUTHMGR-5-FAIL: Authorization failed or unapplied for client (6431.500e.9b00) on Interface Gi1/0/13 AuditSessionID C0A846660000004700DF6030
    Oct 24 10:53:47.648: dot1x-ev:[6431.500e.9b00, Gi1/0/13] Delete auth client (0x15000045) message
    Oct 24 10:53:47.648: EAP-EVENT: Received free context (0xE8000047) from LL (Dot1x-Authenticator)
    Oct 24 10:53:47.648: dot1x-ev:Auth client ctx destroyed
    Oct 24 10:53:47.648: EAP-EVENT: Received LL (Dot1x-Authenticator) event 'EAP_DELETE' on handle 0xE8000047
    Oct 24 10:53:47.648: EAP-AUTH-EVENT: Freed EAP auth context
    Oct 24 10:53:47.648: EAP-EVENT: Freed EAP context
    Oct 24 10:53:48.621: EAP-EVENT: Stopped EAP tick timer
    Oct 24 10:53:49.485: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up
    Oct 24 10:53:50.491: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up
    Oct 24 10:53:53.528: dot1x-ev:[Gi1/0/13] Interface state changed to DOWN
    Oct 24 10:53:53.528: dot1x-ev:[Gi1/0/13] No DOT1X subblock found for port down
    Oct 24 10:53:54.518: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down
    Oct 24 10:53:55.524: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down

    Hi Jatin,
    See below the data that you have requested.
    show run bits.
    aaa new-model
    aaa authentication dot1x default group radius
    aaa session-id common
    clock timezone BST 0 0
    clock summer-time UTC recurring last Sun Mar 1:00 last Sun Oct 2:00
    dot1x system-auth-control
    interface GigabitEthernet1/0/13
    switchport access vlan 80
    switchport mode access
    authentication port-control auto
    dot1x pae authenticator
    spanning-tree portfast
    interface GigabitEthernet1/0/48
    switchport trunk encapsulation dot1q
    switchport trunk native vlan 70
    switchport mode trunk
    radius server NPS1
    address ipv4 192.168.19.121 auth-port 1645 acct-port 1646
    timeout 10
    key thesecret
    ip default-gateway 192.168.70.1
    SW1-randy#show auth sessions interface gig 1/0/13
    Interface    MAC Address    Method       Domain          Status    Fg Session ID
    Gi1/0/13     803f.5d09.189e N/A          UNKNOWN      Unauth         C0A846660000002F00251DBC
    SW1-randy#Show mac address-table Interface GigabitEthernet1/0/13
              Mac Address Table
    Vlan    Mac Address       Type        Ports
      80    803f.5d09.189e    DYNAMIC     Drop
    SW1-randy#ping 192.168.19.121
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 192.168.19.121, timeout is 2 seconds:
    Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/8 ms
    Here is a wireshark of the accept packet.
    Message was edited by: randy coburn
    Added wireshark trace

Maybe you are looking for

  • How do I get an old library to a new computer? Old one crashed

    How do I get my library of music to a new computer? I authorized the new computer but nothing is going to the new computer Please help

  • Remote Login Not Saved

    Dreamweaver no longer saves the login information for my remote server. I enter my login and password, select the Save checkbox, but every time I close, then reopen Dreamweaver, the login information disappears-it is not saved! This did not always ha

  • Latest nokia music converting files gone?

    I updated Nokia Music a couple of weeks ago. IN this new version I can't find the option to automatically convert mp3 to aac before transferring them to the phone. The older version did all that automatically.  I don't understand how a "newer" versio

  • [INSTALLATION] Connect Xampp and MySQL?

    Hi, I want to install MySQL-PHP-Apache. The first thing I did was to download and install MySQL. Then, I installed Xampp. The main reason why I installed MySQL separatly was to be able to use MySQL from a command-line. With the Xampp install, we can'

  • Lookout server process control through modem from remote site

    Hi! I want to control the lookout version 5.0 server process from my office by using the simple 56k internal modem and telephone line. I know the congiguration for sever /Client for  Local Area Network (LAN). 1. I have server process. 2. I have clien