Azure VLAN Servers Can't Communicate

I have been running two Windows Servers 2012 r2 boxes in azure for a few months now and all of a sudden they can't talk to each other
in anyway. I tried this but
it did not seem to help me. Any ideas? I would like to transfer files between the two but no matter what I do they can't find each other. When I do a tracert it shows me the correct dns name for my server but tells me the destination host is unreachable. A
week or so ago I used a powershell command to set the ip's as static in azure so on reboot they would stay the same and I did not have any problems for a week or so after that until this came up. I also have them set in the host file so I can talk to them
via name but neither name or ip seem to work for communication at this point. Thanks for any advice.

I have one set for 10.0.0.4 and 10.0.0.5 which is what their ip's were before I set them static and they are the only two servers in the vlan. They also worked fine for about 2 weeks being static until today. I have all windows firewalls turned off on both
machines as my first guess was an update turned it on. I have rebooted them multiple times but I am going to try an azure full shutdown to see if that does the trick. I have not made any changes to the DNS and my gateway is correct 10.0.0.1.
As I was writing this I did a full azure shutdown which seems to have fixed it. I can now talk between servers without issue. Hmmm, this is very bothersome. I run a nightly task to load data from one server to another for a customer and can not have
these flake out whenever they feel like it. I am hoping I do not have this issue again. My current setup is to only run them a few hours at night and have them full azure power off during the times I do not need them. I currently send a powershell command
to shutdown and deallocate "stop-azurevm -servicename $servicename1 -name $vmname1 -force" so I am not billed for run time I do not need. Is there a better way to do this? I only need them to run a few hours a day to perform their duties but
it seems like having them force shutdown is causing lots of headaches.

Similar Messages

SCCM 2012 What Ports Do I need to open so DMZ servers can communicate with my SCCM Server?

Hi,
What ports do I need to open in the firewall so my DMZ servers can talk to my SCCM server on the network?
Here are my steps before to make my DMZ servers talk to my SCCM server:
1. On my SCCM 2012 SP1 CU2 I have bounderies installed --> I install SCCM Client on my DMZ server with the appropriate switches --> I go back to my SCCM server to approve the server --> Works
But now my DMZ servers stops getting definition updates from my SCCM server and I was suggested that it is much easier to open ports in DMZ.
Now, could you please tell me what ports should we open to ensure two way communication among servers?
Thanks!

Yes and no. It's a bit muddy at times.
For Internet based clients, putting an Internet-enabled MP in the DMZ is perfectly acceptable because Internet clients will only choose MPs enabled for Internet communication.
For systems in the DMZ, that's where it really gets muddy. There's no perfect way to accomplish this. IMO, DMZ clients should be allowed to go back to the MP/DP in the Intranet with a targeted opening in the DMZ firewall rules that allows them to only go
to the internal MP. That's a security policy question though for your organization.
Another option is to treat the clients in the DMZ as Internet only clients. This way, they will only go to the Internet MP in the DMZ. You do lose some functionality though like Remote Control.
A final way is to actually put an MP/DP in the DMZ and deal with the timeout's that happen when clients try to talk to the MP in the Intranet. Clients will try 5 times to contact that MP before giving up. They try to find a new MP at the following times
(which are not configurable):
- Every 25 hours
- WHen the client detects a network change
- When the client agent starts
Jason | http://blog.configmgrftw.com

Migration between two environments which can't communicate with each other

My customer is intending to do migration from test environment to production environment using CCM.
But the two environments are not in the same network.
The environments' setting is as blew.
BO TEST Repository can communicate with Web BO Server.
BO PRODUCTION Repository (Cluster environment) can communicate with Web BO Server.
BO TEST Repository and BO PRODUCTION Repository (Cluster environment) are in the different network, they can't communicate with each other.
Setting Target Repository manually in CCM.
Questions are:
1. In CCM, as long as both Source Repository and Target Repository can communicate with Web BO Server, the migration will be successful.
Is that right?
2. If 1 is not right, is there additional setting should I do?
For example, If I need to open some firewall port?
3. Is there other attentions should I notice?
Thanks

Questions are:
1. In CCM, as long as both Source Repository and Target Repository can communicate with Web BO Server, the migration will be successful.
Is that right?
Yes that is correct
2. If 1 is not right, is there additional setting should I do?
For example, If I need to open some firewall port?
You have another option which is to use the BIAR files. Export your objects to a BIAR file in source environment, and import them from BIAR into the target environment
3. Is there other attentions should I notice?
when using BIAR files as solution, Make sure that you keep them < 1GB size to avoid corruption
you may have to increase or adjust timeouts on input and output repository servers as well

Wlc can't communicate with dhcpserver

Our wlc can't communicate with any host on vlan Z (subnet 192.168.1.0/24). The wlc itself is in a different vlan. All communication to other vlans works just fine. I've temporarly disabled the access-lists for vlan Z, without success. A host in the same subnet as the wlc is able to establish communication with a host in vlan Z.
How to solve this problem?
Kind regards,
D vd Wege

Please see link below. For inter vlan to work you have to configure dhcp option 43 on your dhcp server. Hope this help you.
http://cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00808714fe.shtml

I'm getting an error message saying that "iChat can't communicate with the AIM account __"

I'm getting an error message saying that "iChat can't communicate with the AIM account __" I don't know what to do because google.com isn't coming up either...Please help!

Hi,
For any AIM valid Name (AIM, @mac.com or MobileMe) go to the IChat Menu > Preferences > Accounts
Select the account in the list then in the Server Settings tab change the port from 5190 to 443
Also try it without the SSL option.
(Go to the Account info tab to select the Use this Account option to Log in).
Do you mean you have a GoogleTalk account of some kind ?
One based on Google Mail accounts (@gmail.com or @googlemail.com) should have talk.google.com listed as the server in iChat (Server Settings for your Google Account)
There are Other Google accounts (Non Email) that can have Talk Enabled and these do connect to a server called google.com
Both these forms login to the Jabber servers involved on port 5223 and use SSL
It is possible with Google though to also change this to port 443.
(Other Jabber servers will not allow it)
8:20 PM Friday; June 3, 2011
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb( 10.6.7)
 Mac OS X (10.6.7),
"Limit the Logs to the Bits above Binary Images."  No, Seriously

Can UCE communicate to the Universal Knowledge Base and Universal Software

Question
Can UCE communicate to the Universal Knowledge Base and Universal Software Component Repository through a company proxy server?
Answer
During the install process of the OnStage Management Server, the OnStage EZ-installer will detect your local proxy server whilst establishing communications with the Aduva Universal Servers.
In this instance, the user is prompted for the proxy parameters, including IP address of the proxy or proxy server name if DNS is present, proxy user name and password.
This information is stored locally in the .director.rc file and is never communicated to Aduva or any other 3rd party.
Once the proxy settings have been correctly inputed during installation, OnStage will indeed work through the proxy server.

Welcome to Apple Discussions.
I assume you have already tried what has been said in this: iPod shows up in Windows Explorer but not in iTunes, iPod Service Error or Please reinstall iTunes and Fast User Switching in Windows XP is not supported?
Sorry if you have, but have to know first.

IChat can't communicate with the AIM account error window! please help!

Hello, I have been trying to connect to my AIM account via iChat and for some reason it doesn't let me. A window saying the following appears:
"iChat can't communicate with the AIM account "name of account".
"An undefined AIM socket error has occurred."
Please help with this. What is going on?

Hi,
An @Mac.com name is a valid AOL/AIM Screen Name.
Any Issues and the AIM servers will say the AOL/AIM name or password is incorrect.
As I said earlier, there can be issues if when you create an @Mac.com or even a MobileMe account Apple lets you create passwords of up to 20 characters (I think).
The issues is the AIM Server can check the name with Apple but don't parse Passwords that have more then 16 characters (You have to change the Password to 16 characters or less).
There is also another issue.
Creating a Name at the @Mac.com page allows you to use spaces as valid characters (As In ralph [email protected]) but again the AIM servers cannot parse these names as Spaces are not Valid at AIM
Use iForgot to check the name. You can also change passwords via this.
Use the On Line option and answer the security questions.
That should confirm whether the account/Screen Name/Apple ID works.
Then go to this page https://settings.aim.com/
Use the Sign In option top right.
Enter your @mac.com name and password (It will read AOL at the next page to do that)
If it works properly then you should be returned to the page I linked you to but it will now have your Screen Name showing above the menu area.
This will confirm that the @Mac.com name is accepted as a AIM Screen Name.
If you are still having issues, go to the iChat Menu > Preferences > Accounts
In the Account Info tab make sure you are logged out (Deselect "Use this Account")
Go to the Server settings tab
Change the port from 5190 to 443 (it may also pay to deselect SSL)
Log back in again.
Deleting com.apple.ichat.AIM.plist may help.
If the issue is an incorrect password you may need to delete the entry from the KeyChain (Use KeyChain Access in the Applications/Utilities folder)
Hope this helps.
9:33 PM Thursday; March 10, 2011
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"

IChat can't communicate with the Jabber account

Got the instructions for "Configuring iChat for Google Talk" from Google at:
http://www.google.com/support/talk/bin/answer.py?answer=24076
But after adding my Gmail info. I keep getting this error message:
iChat can't communicate with the Jabber account "[email protected]"
Anybody out there come across this and solved this sucker?
THANKS

Hi,
You have entered the account info as a Jabber Name and not chosen the Google option
With iChat Open go to the iChat Menu > Preferences > Accounts
Click on the Plus Button at the bottom of the List.
In the top item in the new pane Choose GoogleTalk.
Add your ID exactly as it appears when you Log in to the Web Mail page at Google (Mail seems to except either ending, @google.com or @gmail.com but the Google Talk server does not)
Enter in the password
Click the Done button
You should now have Buddy List that Logs On
In the Account list in iChat you will now have at least three Accounts Listed (the faulty one, the new one and Bonjour)
If you then check the Server Setting tab/button on both the "google" accounts you will find the new one says the server in talk.google.com
The other will use the last part of your ID (in your case you entered a name/ID ending @gmail.com).
The reason for your confusion is that those Google Instructions are for iChat 3
You have "Missed" the bit about changing the Server Name in the Server Setting tab to talk.google.com as in fact you can add it as a Jabber account and then change the server name the same way.
You could change the server info in the "old" account or you can highlight it the list then press the minus button to Delete it.
One other thing.
It is important that Talk is Enabled in your everyday Google Account Setting (Not the mail ones).
This does add the Chat option to the Mail Web page and of course allows iChat to use the GoogleTalk servers.
I have several Jabber Accounts including Google as well as several AIM valid Logins.
I don't find the Google servers go Off line or drop connections any more (Nowadays) than the AIM ones or other Jabber servers.
9:21 PM Monday; May 23, 2011
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb( 10.6.7)
 Mac OS X (10.6.7),
"Limit the Logs to the Bits above Binary Images."  No, Seriously
Message was edited by: Ralph Johns (UK)

I am getting an error message when trying to burn pictures to a dvd rw, and it says the disc can't communicate with the drive?

I am trying to burn some wedding pictures to a blank dvd rw. I keep getting an error message that says the drive and the disc can't communicate. I have run a repair disc and repair disc permissions, restarted my laptop, and still get the error. What else can I do?

Hi sheryl525,
Welcome to the Support Communities!
The article below may be able to help you with this issue.
Click on the link to see more details and screenshots.
Apple Computers: Troubleshooting the slot-loading SuperDrive
http://support.apple.com/kb/HT2801#
Cheers,
- Judy

Computers on network can't see each other and can't communicate

I have a Linksys router, WRT54G, which calls itself wireless but has only wired connections.   I have my computer and my phone (for Vonage service) plugged into it.    My router is then connected to the household router by a CAT 5 cable.   The household router is also a Linksys; wireless and with plugs for a half dozen computers.
I get teh Internet fine with no problem, but we want to share my printer on the household network.   My housemate cannot see me on the household network and can't see my router either, and can't communicate with my computer with the \\Name command.   I can't see the household network and can't communicate with my housemate's computer with the \\Name command.
I am running Windows Firewall.   I am sure that so is my housemate.
Is there something special we have to do to set up our routers for the household network to work properly?
It looks like I'm supposed to configure my router to communicate with another router instead of connect directly to the Internet, but when I tried htat and enabled interactive adjusting or whatever I suddenly couldn't access the Intenet and my phone couldn't get a dial tone, until I changed it back.
Tehre isn't any explanation of how to do it anywhere.   There aer technical descriptions of what each thing does but I don't see where it says how to set it up or how to troubleshoot.
I don't know if we were supposed to set up networks and manually add each other's computers. Apparently my housemate did not have to do that with his wife's computer or his notebook.    They just show up in the network.
Yours,
Dora

Thanks for your help.   Unfortunately between when I last looked at your name and when I managed to reply I forgot your name.
1. For the option that the parts of the network can see each other, you plug the cable into the OUTGOING port of the SECONDARY router?    That doesn't make a whole lot of sense; how cuold that possibly work? The way I understand it, the signal can come in only through the incoming plug, which you call the "internet" plug, if I'm understanding you.
2. If you choose the setup that makes any sense - the cable is plugged into the incoming plug - the "internet" plug - on the secondary router, and the ethernet connection on the primary router, can all the computers see each other and their resources, ie, printers they want to share?
3. If not, why on earth?
4. for the second option, it looks like some steps are missing.   Why don't you need to disable DHCP and set the router to be a secondary router?
PM me for my contact details.
Thanks!
Yours,
Dora Smith
(Mod note: Edited post for guideline compliance. Email address removed. Use the PM system please. Thanks!)
Message Edited by JOHNDOE_06 on 02-25-2009 08:39 AM

In hotel w/wireless network. ATV finds network, but does not ask me for password, so can't communicate through network. MacBook Air, iPad and 2 iPhones connected to hotel wireless, but ATV does not ask me for the password. Any ideas?

I have succesfully connected a MacBook Air, an iPad and two iPhones to the wireless network in this hotel. Apple TV can see the network and "connects" to the network, but w/o asking for password. I expected to see a screen immediately after selecting the network that asked me for the password as did all of my other devices. ATV did not ask me for a password. When I go to Settings>General>Network, it shows the name of the hotel wireless network, but I can't communicate with the network. It can't set date and time. When I try to enter my Apple account name and password, it tells me it can't log in w/o setting date and time.
Any ideas on how to connect to this network?

I am having the same problem. In my hotel when I connect my laptop a screen will pop up and you have to hit the button "I Accept Terms". However I can't do that with the ATV. I called the internet provider and they said they could not help me. Any ideas? Do you think the guy just doesn't know what he can do for me? I am thinking I will call later and hope to get a different technician who might know how to help connect me.

Driver can't communicate with new officejet pro 8610 for scanning

I just bought a new officejet pro 8610. Followed all directions and set up with wireless connection. Prints fine but will not scan. Will not work if used at control panel on printer or software. First tried it on a windows 7 machine. Just tried on a new windows 8.1 machine - same problem. Very frustrating. Have done the HP scanner doctor and when it gets to driver it says scanner driver can't communicate to product. Used disk and then went to HP web site and downloaded latest software and drivers - still does not work.
I'm about ready to take the printer back but am open to any ideas.

Hi @ecsteve
It is possible you have a firewall or antivirus that is blocking the scan communication. Printing is considered outgoing and is not considered a threat, but because scanning is incoming communication, an antivirus or firewall could be blocking it to protect the computer.
If you have Norton, take a look at the following link; I cannot configure or access a network printer or other devices after I install my Norton product.
I found this in a post by @Norton_Support . If you have a different Anti Virus program, let me know and we will work through this together to come to a solution. Thanks.
- In support of Movember
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

I accepted a recent update for iTunes and now my version of Spin Doctor can't communicate with it any more. I don't think I can upgrade the Spin Doctor without buying a new program. Is there a way to undo the last iTunes update?

I accepted a recent update for iTunes and now my version of Spin Doctor can't communicate with iTunes, specifically, I can't get music files to go over to iTunes. Spin Doctor gives me a message indicating that iTunes isn't working properly.
I am using iTunes 9.1.1(12) and Spin Doctor 3.1.1.304t. I have investigated upgrading the Spin Doctor but I think too much time has passed and the version available are too far advanced.
Any ideas? Can I undo the iTunes upgrade? Is there a website that I can go to to get the upgrade for my Spin Doctor?
Thanks.
Mary

If your iMac is an Intel CPU model, you can upgrade the OS to OS X 10.6 Snow Leopard.
Then use software update to update 10.6 Snow Leopard to OS X 10,6.8.
Then you can run the latest iTunes to sync your iPad running iOS 6
You can purchase OS X 10.6 Snow Leopard by calling Apple at 1-800-MYAPPLE. Ask for retail software sales and purchase a copy of 10.6 for $19.99 plus shipping.

Computer Can't Communicate With Printer

Hi,
After installing Win 8.1 on two different computers, both have the same printing problem.
The first problem that appears is "Bidirectional Support" must be enabled... It was enabled in Win 8 prior to the upgrade...
It took awhile to figure out how to enable it, as after every attempt to check the box, the check would disappear after closing and reopening the window.
It turns out that this won't work with the printer connected. After disconnecting the printer the setting will stick, and when the printer is reconnected it stays that way...
Unfortunately this doesn't resolve the problem... Now I get the error that the computer "Can't Communicate With The Printer"
Attempts to reinstall the software\drivers have been for the most part useless... Even after removing the printer in Devices and Printers and uninstalling the software\drivers, the Driver installer insists that the drivers are still installed and will only
"Update" them, or "Install Another Copy"... neither of which resolves the problem...
On one occasion, I was able to get a complete install, but only after doing a search through the Registry and Deleting everything that came up concerning the printer... This still didn't resolve the problem.
On one machine, after doing this, the Print Spooler would hang and run the CPU at 50% indefinitely. After playing around awhile, I found that if I turned off the Print Spooler in "Services" while it was doing this, and then restart it, the file
would actually print properly...
I have checked the settings in Windows Firewall, and everything for the printer is "Allowed". I even turned the Firewall off to no effect...
This is a Lexmark X5340 USB inkjet printer that works perfectly on the same machines when running Win 7 or Win 8 with all the same connections, software, drivers, and etc....
Is there something different with Win 8.1 than Win 8 concerning printers?

Hi,
I wanted to let you know that I've stumbled upon a way to get the Lexmark software\drivers to reinstall on the Win 8 to 8.1 Upgrade...
It has to do with the Print Spooler interfering with the uninstall\reinstall process. I had read about a recommendation to turn off the Print Spooler before uninstalling the software quite some time ago, and I had tried that, but it didn't work. Here are
the tricks to get it to work if it isn't too late for you.
Note: Bidirectional Support is needed, and for some reason the upgrade process turns it off. This may also be related to the Print Spooler....
1) Turn on and hook up your printer... This needs to be done just this one time to get it to show up in Devices and Printers.... Otherwise, all I get with my machine is the Lexmark Fax, and as a result, you can't "Remove" the printer.
2) Once the printer is visible in Devices and Printers, unhook it..
3) "REMOVE" the Lexmark Printer and Lexmark Fax (if you have one) in Devices and Printers.
4) Stop the Print Spooler in "Services"
5) Uninstall the software\drivers... In the process of doing this, I got a popup Security message from Windows Firewall concerning "Allowing" Printer Communication... I selected "Allow".
6) At the prompt from the Lexmark uninstaller, Reboot.
7) After rebooting, stop the Print Spooler again.
8) Reinstall software\drivers... I used both XP SP3 and Vista Compatibility Mode on different attempts, and both worked... Hook the printer back up when prompted by the installer.
9) Unhook the printer again and reboot. Bidirectional Support must be Enabled, and the setting won't stick if the printer is hooked up.. You need to reboot to clear things up before the next step.
10) Enable Bidirectional Support and Reboot. To do this, go to Devices and Printers and select "Printer Properties" and then the "PORTS" tab... The check box is near the bottom.
11) Set any Printer Preferences you use, if any, and it's ready to go.
I just noticed that when I right click on the Lexmark Preferences, Properties, etc., it is showing two of them for some reason. I don't remember that happening the first time I tried this, but I might have missed it.
I'll need to investigate that a bit.
EDIT... It seems the second printer doesn't show up until after Enabling Bidirectional Support...
I guess that makes a little bit of sense... two printers for two directions.
Thanks for the info. I found it was necessary to change the print spooler. You will also need to set another service that is used during printing that provides screen interaction for the print spooler. Make both of them automatic.

IChat can't communicate with my AIM account

Hi, every time i try go to to my ichat it automatically logs me out, and when i try to log back in, it says "iChat can't communicate with the AIM account 'aforever0203' and The AIM server has temporarily limited your account due to too much activity. Try again in a few minutes" This has been happening for days, please help!

HI,
Go here https://settings.aim.com/
Can you sign in there ?
This will not work for newer @me.com and @icloud.com IDs issued under iCloud ( I notice there are at least 2 Me Toos clicked)
With Apple IDs there have been issues over the last few months about accounts getting Suspended when people have travelled to foreign lands.
The "normal" fix with AIM names is to Change the Password but obviously changing the Apple Passwords cannot be seen by AIM.
In that case you need This link about Suspended accounts and you need to use the TOS General email address.
(You need to explain very carefully that you have an Apple ID and that AIM cannot see any Password Change and that they will have to reset the account manually - some support staff seem not to know that Apple have an agreement that Apple IDs are also AIM Valid Names)
If it is a plain AIM name a Password reset should correct the issue.
11:09 PM Saturday; January 12, 2013
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 iMac 2.5Ghz 5i 2011 (Mountain Lion 10.8.2)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad
"Limit the Logs to the Bits above Binary Images."  No, Seriously

Azure VLAN Servers Can't Communicate

Similar Messages

Maybe you are looking for