Barcode printing on EPSON dot matrix
Hi,
We are printing barcode on Invoice using EPSON dot martrix. We created a new bar code using New Barcode technology through SE73 and created a ZPDF417 type .We taken a PDF417 symbology in New Barcode Technology.
While using this , the data is printing in Barcode. But while scanning the data is not reading.
The same print taking from HP Laser or HP DeskJet , it is printing and also reading while scanning.
Why i am facing problem with Dotmatrix.
If any suggestion pls give me.
Thanks in Advance,
Pavan.
Hi Pavan,
Dot matrix printers offer the lowest resolution of all available printers. Although dot matrix printer manufacturers claim resolutions as high as 360 dots per inch, the real resolution of most is only 60 dots per inch. Higher resolutions are simulated by overlapping consecutive dots. The reason that the true resolution is only 60 dots per inch is because the width of each dot is approximately 1/60th of an inch (16 mils). In order to print readable bar codes on a dot matrix printer, the Narrow Bar Width must never be less than the width of a printer dot as it is impossible for a dot matrix printer to print a line narrower than the width of a single dot. The larger the value that you choose for the Narrow Bar Width (within the allowable range for a specific symbology), the more readable your bar codes will be.
When you set up the Windows printer driver for your dot matrix printer you should select the highest dot resolution that the printer is capable of. If the driver has a Dithering option, you should also select "Line Art" or the finest dithering resolution that is supported. Some dot matrix drivers also allow you to set the intensity or darkness of the printing. If your printer supports this feature, you should set the intensity to the darkest level supported.
So i think in your case you need to tell the EPSON printer to use a minimum pitch-width in combination with UNI-DIRECTIONAL printing (Uni-directional escape character for EPSON = ESC U).
The pitch-width is something that must be setup standard for the printer (ask the system guys).
The UNI-DIRECTIONAL flag can be send prior (but part of) the actual barcode. The ESC charachter has ASCII value 027.
Most likely with UNI-DIRECTONAL print, your barcode will become readable.
Hope this helps you along.
Regards,
Rob.
Similar Messages
-
Second page not printing on EPSON dot matrix
Hi Experts,
I have created a Smart Form which has 2 pages. I am able to see the Print Preview correctly of 2 pages, (Spool also shows correctly), but when I give the print on EPSON DOT MATRIX PRINTER, only one page is getting printed. Somewhere it seems that second page is getting overlapped on the first page. Its very strange behieveour. Dont know why its happening.
Any ideas ??I have done it. Well issue was: \f command needs to be used when you create the custom page in the device type--->formats->your custom page----End of page.
In end of page simply write \f and printer will stop over writing the pages
Thanks. -
Crystal report printing using epson dot matrix printer (continouos paper)
Hi there, im tiff from the philippines.
i have a question on printing using a crystal report. How do i print using epson continuous printer(dot matrix)? im having a problem printing to that type of printer specially using continuous paper. the first page is correct but unfortunately the succeeding pages are not. its automatically adjusted upon reaching the second page. hope you can help me.
thanks a lot and looking forward to hear from you soon.
tiffCheck with the printer manufacturer that the matrix printer is Unicode compliant. If it is not, it will not work with Crystal Reports. If it is, make sure you have the latest printer driver updates.
Download SP 1 for CR 102 from here;
https://smpdl.sap-ag.de/~sapidp/012002523100006007872008E/crvs05sp1.exe
See the following resources re. printers;
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/a09051e9-721e-2b10-11b6-f9c65c64ef29
[Note #1314394|http://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/oss_notes_boj/sdn_oss_boj_dev/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/scn_bosap/notes.do]
Ludek -
BMP image not printing on LIPI Dot MAtrix printer
Hello everybody .
I am facing a promlem while printing a signature ( bmp image ) in a report .
In print preview it is showing coreclty but while printing to LIPI Dot matrix printer model TALLY 2500 that Signature( bmp image ) is not getting printer.
Can anybody let me know wether any setting is to be done from SAP side .
Thanks in advance .
Regards
Dhaval..Hi Raje,
Try to take the print in inkjet or laserjet printer
just for confirmation purpose .
if it prints in that and doesn't print in dot matrix then the problem is with the dot matrix.
In that case ask the basis guys to install the relevent device driver for that dot matrix printer( as normally they would have installed some generic driver ).
Hope this helps.
Regards,
Guru
*mark helpfull answers -
Problem while printing smartform in dot matrix printer
Hi Experts,
When i am printing smartform using dot matrix printer only the last page prints but all the pages displays in print privew.
For example suppose there are three pages to be print 1/3, 2/3 , 3/3 , i get all the three pages in print privew as well as when i take its printout in laser printer i get all three pages as print, but when i am using dot matrix printer i get only the last page ie 3/3 as print.
Regards
Varun SharmaHai Varun,
If things are coming properly then its no more ABAP issue.
Need to check out with the BASIS team along with the IT / hardware department.
Just try to take print out on a other dotmatrix printer, if its somewhere close to you as usually they are heavy and large in size can't be moved.
Hope this helps,
Cheers,
Suvendu -
Which driver to use to print to a dot matrix printer?
All-
Hi, we are using Adobe Output Designer 5.7 to create invoice templates. We use a custom application that uses Adobe Output Central Server (5.6) to create invoices and print them to a network printer. We are about to do a new release in Chile, which requires a dot matrix printer be used for printing due to gov't regulations. Does anyone know what kind of print driver could be used to effectively print to a dot matrix printer? It seems like all the drivers we have used don't work.
Additionally, we also tried using the .pdf driver in conjunction with the Web Output Pak, but unfortunately that result is just as bad. Does anyone know of a workaround to get Pdf's to work with a dot matrix printer? By googling, I found that we could try copying the .pdf output and pasting into Word, but I haven't tested this yet and it makes for a cumbersome process.
Thanks,
AndrewHi Andrew,
Unless you can convert the PDF to a text file, and print that, I doubt there is any way to send PDFs to a Dot Matix printer.
If you're on Windows then one way is to use the 'windows' driver option in your template to generate the output directory for the target printer - this allows non-supported printers to be used with Output Server,
Regards,
Paul -
Printing over a Dot Matrix Printer
Hi,
I want to do printing on a Dot Matrix Priner. Can any body help me how to perform this task.
Regards,
Umar ToseefYou can either,
- use the OS drivers using the Java Printing API
- write the printers codes to is directly using the Java COMMS API
- buy another printers.
My preference would be for the last one! -
Web report printed on a dot matrix printer
Dear all,
how can i design a report that is going to be printed on a dot matrix printer, i want to know these things:
1 - what i will have to change in the report it self.
2 - when i call the report from the form how the code will be.
3 - do i have to print the report on the browser then the user press print from the file menu of the browser.
please advice1 - what i will have to change in the report it self.Since you will be printing to a dot matrix printer, you essentially need to design a character mode report and set the .prt file for printing purpose. Check in online help for how to make a character mode report.
2 - when i call the report from the form how the code >will be.On the otn site itself, you can find a white paper on reports 9i/forms integration. Please refer to this white paper on the example code.
3 - do i have to print the report on the browser then >the user press print from the file menu of the browser.You do not need to print the report from browser window and can directly tell the report to print the character mode output using your dot matrix printer. The command line you send from Forms will have destype=printer and desformat=<.prt file name>
Thanks
Rohit -
PO printing issue in Dot Matrix printer
Hi expert
We got unnecessary spaces on the second page while taking a PO print out.
printer is dot matrix- EPSON LQ2180.
Page Format DINA4
Device type is EPESCP2
Can any body help in this matter?what have i to do remove unnecessary spaces from PO printout?
And also i can not under stand the code which was written in Page Format DINA4?
please find below codes.Help to understand the below code as well.
Printer initialization
reset
\e\0x40
designate codepage for slot 0
\e\0x28\0x74\0x03\0x00\0x00\0x03\0x00
select codepage from slot 0
\e\0x74\0x00
set line spacing 6 LPI
\e\0x32
set page length to DINA4 (=70 lines at 6 LPI)
\e\0x43\0x46
cancel bottom margin
\e\0x4F
set left margin to 0
\e\0x6C\0x00
select LQ quality
\e\0x78\0x01
select non-proportional spacing
\e\0x70\0x00
Thanks
MM
Edited by: samir DODIYA on Feb 28, 2012 1:30 PMThere is something I don't understand: if the barcode printed is visually correct, and exactly the same as with a laser printer, why do you want it would be better with a PDF (especially on a dot matrix printer).
Could you also tell us what symbology you use, and do you use smart form new barcode technology? -
Text shifting Right when printing smarform in Dot matrix printer
Hi all,
I have developed a payslip in smart form. I am printing the smartform in dot matrix printer. when there is blank between 2 values like one of the deductions is blank between 2 values while printing its will shift to right indefinitely even though in the print preview it is appearing correctly. In the same way in the last line i am printing Total earnings deductions n net pay... Total earnings has to be printed approximately after 6 cms from left margin in print preview it is exactly where i wanted but when printing its printing after almost 8 - 9 cms
I have created a Z page format to fit the copying 6 inch page and added code to make necessary changes to print in continuously
Kindly help me to overcome the issue.
Any help appreciable....
Shivakumar K B
09098955022Hi Pavan,
I am trying to display the text in the template which is of the exact size as in preprinted stationary, in paragraph format i am not using space between variables..
To be clear.................... I am getting my print preview is correctly but when i give it for printing the text is shifting right... -
Printing smartform in Dot matrix printer
Hi ,
i am giveing the printout of the smartform in the dot matrix printer. But in the print out the template is not getting printed and in the second table i am getting extra lines in the table. Please give me any suggestions and is there any settings to be changed in the printer.
Warm Regards
Phani.There may be some isssue with the loop used to printing the table ....
There might be only 2 reasons either there is loop repeating or not data is not cleared concentrate on this two issues only .
try debugging the table jus before printing .if its is fine , then
Sometimes even the problem with the print catridge could have resulted in this .
Edited by: Martina Floriette on Jun 23, 2009 7:50 AM -
Printing problem in Dot matrix printer
Hi all,
We are planning to use Dot matrix printers for printing through SAP.We do front end printing using Windows OS. I am able to get prints properly if it is a script form. In case of list outputs, printer is printing the text outside the paper.Only half of the text is printing on the continuous stationary. Actually document is to be printed in Landscape format. So printer should print data vertically on the paper,but it's printing horizontally. I have created sparate output device for this printer.My printer is TVS Electronics HD745 24 Pin heavy duty printer. I have assigned OKI341 as device type for this device.Any more settings I need to do to get printing in landscape mode?Hi,
Dot matrix printer.
Problem with pritning with dot matrix
About Dot matrix printer device problems
Regards,
Sandeep -
Printing Reports on Dot Matrix Printer
Reports are printing very slowly on Dot Matrix Printer. If any solution Please tell me.
[email protected]hello, I could not write English, but I will help you
You could see it in SYSTEM PARAMETERS of reports, in the MODE option, putting the to initial value Character type
You also have to see the Dflt.prt file, that this located in the C:\ ORAWIN95\ REPORT60\ PRINTERS, the who you control the margins of
impression in manner [caracter]. They for [default] are 80 Columns and 66 Lines, the
who you could publish and change the courages
You count me if I operate you.
Greeting -
Printing Reports to Dot-Matrix Printer
I have a customer that is trying to print a report to my company's dot-matrix printer and we keep seeing a "bold/unbold" command (7B, OB) where we should be getting actual bolded text. Is there anyone who has experience printing Oracle reports to a simple dot-matrix text printer? Can you suggest a printer emulation or fix?
The dflt132,dflt like.. files in c:\orawin95\rdbms\reports\print(may be dir is correct) for the printer and make sure that the file contains the correct escape sequence
like if bold escape "70",etc..
if you know Foxpro Special Char values,the samething you can apply in the dflt files.
Hope this helps.
null -
Adobe print form on dot matrix printer
Has anyone tried to print adobe forms into a dot matrix printer i.e. printing multi-part documents. I've read that the device type supported are PostScript, PCL, PDF and ZPL. The help file specifically mentioned that SAPWIN device type won't be supported, but it does not mentioned explecitly weather ASCII device type or device type for dot matrix/impact printer is supported or not.
I'm still holding up hope that adobe print forms scenario will be able to do this since we are planning to go ahead with 100% adobe form solution.
Any info would greatly appreciated.The supported output formats of ADS are PostScript, PCL, PDF and ZPL. That means that your printer has to support one of the mentioned formats to be supported. So the answer to your question is no.
Maybe you are looking for
-
Approval procedure in Purchase req or PO- ECC 6.0
Hai, Can we set up a approval routing procedure in Purchase requisition or PO so that if a specific buyer converts / creates the PO - and it's over a specific dollar amount - that it goes to another buyer for approval ? Our department has a very
-
Forms debugger with attached libraries
Hi Is it possible to use the forms debugger with attached libraries ? ( 9I 10g ) And how to do that if it is possible ? thanks
-
Severely problem with SUN HBA card SG-XPCI2FC-QF4 installation
Hello: I'm facing a big problem when installation SUN HBA card,the machine can't recognise the HBA card when poweron with HBA installed, my system is: Server: SUN V890, Solaris 10 HBA: SG-XPCI2FC-QF4 I changed another HBA card and I/O solt,the proble
-
Hi All, While our Trading partners sending 860 and 855, I am getting below error in our B2B reports 850 version 5.1 Machine Info: (essapt020-u009.emrsn.com) Failed guideline. 860 Machine Info: (essapt020-u009.emrsn.com) Validation of Interchange para
-
hi guys, what is MRP based planning and why it is used?Under what conditions do we go for MRP based plannig for procurement of materials?