BIG HELP NEEDED BIG TIME!!!!!

my iPod is not turning on for some reason!! No its no on hold, and yes I tried too reset it. Its just completley blacked out! I was sitting there listening to my music then I was going to charge it but, all of a sudden it went blank!
can someone PLEASE help me please!!

First, let's make sure you're resetting properly;
Hold the MENU and SELECT (center) buttons until you see the Apple logo to reset. It may take several attempts and is best performed while connected to power. You may need to hold the two buttons for ten seconds or so before it actually resets.

Similar Messages

Help needed in Time Capsule configuration

Hello everybody,
sorry in advance for the probably dummy questions, but I have just bought a Time Capsule and would like some advice in order to obtain the best possible configuration for my needs (the configuration guide was not so clear to me).
I linked the TC via Ethernet to my modem/router (I have a Vodafone Station 2), and I have the following requirements:
1) let the TC become the primary WiFi source: what is the best way to do it? Shall I deactivate the Wi-Fi on the Vodafone Station? Shall I create a new network or extend the existing one?
2) create a guest network (possibly with another password): I can I do it? I didn't succeed in doing it...
3) I would like to use the TC internal hard disk both as a sort of reporitory for my MacBook Air backup, and at the same time as an external hard disk; can I do it directly or should I create a partition on the disk?
4) I would like to add another external HD via USB to the TC, in order to have access to its content through various devices (MacBook, iPhone, iPad, PC) linked to the WiFi network. Also in this case I couldn't get it... How should I do that?
5) Finally, I have a question: is it possible to remotely access (e.g. via 3G) the TC hard disk?
Thank you in advance for any help you can give me!!
Regards

dottorslump wrote:
Hello everybody,
sorry in advance for the probably dummy questions, but I have just bought a Time Capsule and would like some advice in order to obtain the best possible configuration for my needs (the configuration guide was not so clear to me).
I linked the TC via Ethernet to my modem/router (I have a Vodafone Station 2), and I have the following requirements:
1) let the TC become the primary WiFi source: what is the best way to do it? Shall I deactivate the Wi-Fi on the Vodafone Station? Shall I create a new network or extend the existing one?
You do not want to extend.. well actually you cannot extend a non-apple router.. so put that out.
The TC will probably have to be in bridge mode.. but it can become the primary wifi source.. simply create a wireless network. Turn off wireless in the vodafone station.
But from your other requirement of a guest network.. you cannot do that in bridge on the TC.. so why not use the vodafone station as your guest network. Give TC wireless a different name. Fix the channels. Try to have them sit a bit apart from one another.. A few Meters at least.
2) create a guest network (possibly with another password): I can I do it? I didn't succeed in doing it...
You cannot do guest network with the TC in bridge. So you need to either bridge the modem and use pppoe client in the TC.. that depends on if your ISP supports PPPoE authentication.
3) I would like to use the TC internal hard disk both as a sort of reporitory for my MacBook Air backup, and at the same time as an external hard disk; can I do it directly or should I create a partition on the disk?
This is not really a good idea.. You cannot partition a TC.. Mixing data and backups can be done but it is not necessarily going to work well. The primary design of the TC is a backup target for TM and mainly looking at laptops.
Look at Q3 here. http://pondini.org/TM/Time_Capsule.html
Pondini is our guru on all things TM.
Particularly remember any files offloaded to the TC have no backups.. And TC is not reliable enough to trust. It is a single hard disk and has no form of automated backup.. nor can TM backup a network drive. Any backup of info on the TC has to be done manually.
4) I would like to add another external HD via USB to the TC, in order to have access to its content through various devices (MacBook, iPhone, iPad, PC) linked to the WiFi network. Also in this case I couldn't get it... How should I do that?
The USB port of the TC is renowned for being underpowered even if the hard drive is powered you might need a powered hub. Some hubs work and some don't so even that is not simple.
USB drive has to be formatted Mac Extended Journelled. Or fat32.
5) Finally, I have a question: is it possible to remotely access (e.g. via 3G) the TC hard disk?
In your case the answer is probably.. but this will not be easy.
Apple's only method is BTMM via iCloud, but the TC must be the main router in the network.
That means you need to bridge your existing modem.
You might be able to get it to work via the existing modem. Please google remote access time capsule.
You will need to port forward AFP to the TC in the modem and use ddns to find the correct address unless your ISP has given you a static IP.
Sorry for the glass half empty answer.

Help needed for Time Calc Java Script

Hi,
I am trying to create a timesheet in PDF and have hit a speed bump. Is there anyone there who could provide me with a script that calculated the difference between 2 times? (Field2 time)-(Feild 1 Time) = Duration.I am desperate and have tried everything.
I proccess the payroll for a company and all of the 500 or so timesheets that I received each fortnight are paper copies and I am pulling my hair out. I need to use Adobe forms (We have Adobe Pro 9 and I am using the XML forms, not live cycle) as the serach engine that we use for emails cannot search on excel documents.
I have no Java script experience and I am getting completely lost in the subject. Any help would be greatly appreciated.
Thanks anyone who can help at all.
-Sohnia

hi friend here example for time calulation start and end time example.. just copy and paste then run it ur browser. <HTML> <script language="JavaScript">  </script> </HEAD> <BODY BGCOLOR=FFFFFF TEXT=000000 LINK=0000FF VLINK=800080> <div align="center"><table width="950" border="0" cellpadding="0" bgcolor="#899194" cellspacing="0"> <tr><td valign="middle" width="33%"> <center> <form> <TD WIDTH=80%> <center> <TABLE ALIGN=MIDDLE BORDER=5 CELLPADDING=5> <TR BGCOLOR=#FFFFFF>  <TD WIDTH=80%> <center> <TABLE ALIGN=MIDDLE BORDER=5 CELLPADDING=5> <TR BGCOLOR="#B6D4D2">  <td colspan=4> <center>Time Between Times Calculations - Multiple Days</center> </td> </tr> <TR BGCOLOR="#B6D4D2"> <TD align="center" colspan=4> Required Data Entry </td> </tr> <tr> <td align="center">Start / End</td> <td align="center">Hour</td> <td align="center">Minute</td> <td align="center">AM / PM</td> </tr> <td align="center">Start time</td> <td align="center"><input type="text" name="hour1" size="5"></td> <td align="center"><input type="text" name="minute1" size="5"></td> <td align="center"><select name="period1"> <option value="1">AM <option value="2">PM </select> </td> </tr> <tr> <td colspan="3"> Add Complete Interim Days</td><td align="center"><input type="text" name="adays" size="5" value="0"></td> </tr> <tr> <td align="center">Start / End</td> <td align="center">Hour</td> <td align="center">Minute</td> <td align="center">AM / PM</td> </tr> <td align="center">End time</td> <td align="center"><input type="text" name="hour2" size="5"></td> <td align="center"><input type="text" name="minute2" size="5"></td> <td align="center"><select name="period2"> <option value="1">AM <option value="2">PM </select> </td> </tr> <tr> <td align="center" colspan=4 BGCOLOR="#B6D4D2"> <input type="button" value="Calculate" onclick="h1=form.hour1.value; h2=form.hour2.value; m1=form.minute1.value; m2=form.minute2.value; days=form.adays.value; am1=form.period1.options[period1.selectedIndex].value; am2=form.period2.options[period2.selectedIndex].value; if(h1 < 0 | h1 > 12) alert('Your start hour is not valid'); else if(h2 < 0 | h2 > 12) alert('Your end hour is not valid'); else if(m1 < 0 | m1 > 59) alert('Your start minute is not valid'); else if(m2 < 0 | m2 > 59) alert('Your end minute is not valid'); else form.answer.value=findtime(h1,h2,days,m1,m2,am1,am2);"> <input type="reset" value="Clear Values"> </td> </tr> <TR BGCOLOR="#B6D4D2"> <TD align="center" colspan=4> Calculated Results </td> </tr> <tr> <td align="center" colspan="4"> Time Difference <input type="text" name="answer" size="40"> <tr><td>[email protected]</td></tr> </td> </tr> </table> </form> </td> </tr> </table> </center> </td> </tr> </table> </center> </TD> </TR> </TABLE> </BODY> </HTML>

Help needed with Time Machine multiple drives set up

Hello, I need help in finding out if what I want to do is possible.
I upgraded to Mountain Lion today as I understood it can handle multiple back up drives. I see how to add a 2nd back up drive, however I do not see a way to put different folders onto different drives.
iMac - backed to a 3TB DRIVE A via the time machine
iPhoto Library original file - already on the 3TB DRIVE A - so no back up for now!
What I'd like to do is to also back up only the iPhotoLibrary file to a 2nd drive - lets call it 3TB DRIVE B
Can it be done with Mountain Lion or not really? I don't even seem to be able to exclude files from an External Disk actually.
Any other software I could use that would do the trick?
Or do I have to rearrange our already messy set up? I've put the iPhoto Library on the DRIVE A as its a faster drive. but I guess the solution would be to put the iPhoto Library original file onto the slower Drive B and only keep the iPhoto file on it?
Hmm any help or tips greatly appreciated.
Thank you in advance.
Marta

Sharlo wrote:
So here's my question: After reinstalling system TM started normal back-up procedure and I get message not enough space on external disk. I use 200Gb for around 100Gb that I have on my computer (I know not so much but works well for me). What I do not get is why does TM need around 30% more space compared to the space I'm using (wants to back-up 130Gb) and why is it not backing-up the system I've just installed but tries to back-up everything from scratch? Is there a procedure to back-up only changed files since the last version?
Ordinarily, that's exactly what TM does. But this situation isn't ordinary. Everything you restored is considered "*new to that disk"* and will be backed-up again. See #14 in the Frequently Asked Questions *User Tip* at the top of this forum, and http://support.apple.com/kb/TS1338
The 30% you ask about is actually 20%; the initial estimate of the space needed might be low, and TM needs workspace on the TM disk, so it adds 20% (see #7 in the FAQ Tip.)

Help needed with time capsule

I have a 3tb Time capsule and Mac set up with Virgin Hub
Back ups work fine but most times i try to acces anything on the time capsule it comes up with not available
It works if i restart or boot through airport utilty
I have the data file with a music sub folder and have a 1 drive plugged to usb both of which seem to be a little to illusive
can you help
Thanks
n

This is a bug on Lion and 7.6 firmware and greater on the TC..
There is no fix.. Ring applecare and ask why it does that.
I suspect Apple will have no idea. Although we have plenty of posts here with the same issue.
I can suggest a bunch of stuff.. nothing from what I gather is a cure.. but it might help.. perhaps this will be auto fixed in ML.
I stick with SL as it has decent networking btw.. and no issues.. !! If you are still on SL you should not have issues if you go back to 7.5.2 firmware on the TC.
First off, tell us a bit more.
Is the TC part of the network, bridged or router or setup independently of the network. Not sure what the virgin hub is.. but please describe the network a bit more.
Try going back to 7.5.2 firmware. Apparently can be very difficult for the most recent versions of TC but if you run lion you should also try it.. download the 5.6 airport utility if not already using that, and try to go back to earlier firmware.
Other things..
Reset the TC and use short no spaces names for TC and wireless. Pure alphanumeric.. no special characters. Is the TC main router.. ?? set the dhcp server to short lease time. Like 10min.. if the virgin hub is the router do the same in that.
Are you connecting by wireless.. ?? Lock the wireless channels and use different name for 5ghz from 2.4ghz to prevent wireless clients jumping around.
When you lose the TC next time.. open terminal and ping it.. by name and ip address.. tell me what happens.

Help needed with timer codes

i have tried to do a countdown timer but can't debug it.. can anyone help me with it or can anyone provide me with the correct coding for countdown timer..
import java.awt.*;
import java.Swing.*;
import java.util.*;
import java.awt.*;
import java.Swing.*;
import java.util.*;
public class timer
 public static void main (String [] args)
 double sec = 150;
 countDown(sec);
 private Thread countDown(double seconds)
 final double time = seconds;
 Runnable runnable(){
 public void run(){
 try{
 Thread.sleep(time * 1000);
 }catch(Exception e){}
 return new Thread(runnable);
 public void displayCountDown(){
 int seconds = 22;
 for(int i = 0; i < seconds; i++){
 Thread trd = countDown(i);
 trd.start(){
 while(trd.isAlive()){
 ; // wait
 System.out.print('\r');
 System.out.print(i);
}

I would suggest using javax.swing.Timer or java.util.Timer instead of implementing it yourself.

Help needed with Time Machine

I've installed Boot Camp because I wanted to play an old game. I understood eventually that laptops are not made for that purpose (my one year old MBP was heating too often and I didn't like that). Unfortunately even during that period I've started experiencing some oddness when switching to Snow Leopard 10.6.2. Eventually I've decided to uninstall Windows and after three hours playing with Snow Leopard in order to make it as it was before I understood I'm not qualified enough to mess with plists and I do not know what else, so brut force solution - reinstalling entire system from the Time Machine.
Everything now works very fast, very nice, I've saved time doing that (soooo happy TM saved my life ... again).
So here's my question: After reinstalling system TM started normal back-up procedure and I get message not enough space on external disk. I use 200Gb for around 100Gb that I have on my computer (I know not so much but works well for me). What I do not get is why does TM need around 30% more space compared to the space I'm using (wants to back-up 130Gb) and why is it not backing-up the system I've just installed but tries to back-up everything from scratch? Is there a procedure to back-up only changed files since the last version?
What I'm doing know is just saving old back-up on a second external drive (just in case if something goes wrong) and I'll "clean" my primary TM disk and then install again ... of course if somebody knows how to force TM to back-up only the files that changed ...
Thanks in advance and cheers,
Sharlo

Sharlo wrote:
So here's my question: After reinstalling system TM started normal back-up procedure and I get message not enough space on external disk. I use 200Gb for around 100Gb that I have on my computer (I know not so much but works well for me). What I do not get is why does TM need around 30% more space compared to the space I'm using (wants to back-up 130Gb) and why is it not backing-up the system I've just installed but tries to back-up everything from scratch? Is there a procedure to back-up only changed files since the last version?
Ordinarily, that's exactly what TM does. But this situation isn't ordinary. Everything you restored is considered "*new to that disk"* and will be backed-up again. See #14 in the Frequently Asked Questions *User Tip* at the top of this forum, and http://support.apple.com/kb/TS1338
The 30% you ask about is actually 20%; the initial estimate of the space needed might be low, and TM needs workspace on the TM disk, so it adds 20% (see #7 in the FAQ Tip.)

Help needed Regarding Time Problem

Dear all,
I am using FM POINT_IN_TIME_CONVERT to convert seconds into HH:MM:SS format.But once HH bcome more than 24,it starts from 00 amd hence my total time goes wrong.What can i do?Is there any other FM?

Hi Rahul,
You have picked up the right function module.Do as following -
This FM have default date 01.01.1980 . Keep in mind that this date have got changed every 86,400 seconds and your time counter reset after that.
At last you need to calculate difference of date and simply add 24 * ( difference you got ) into your hour counter. Thats it.Done.
Thanks
Nimesh S. Patel

Help needed in Time format

Hi
I am using oracle 9i . Is there any option to change the time format ie. for eg: when iam inserting values (in the fields declared as timestamp) as '22-06-2005' it is showing errors but when changed to '22-jun-2005'it is working. In my case i want the values to be inserted in '22-06-2005' format.
Also is it posssible to change dd-mm-yyyy format to yyyy-mm-dd.
Thanking you in advance
Dinny

Hi
When i create a having 'ALTER SESSION SET NLS_TIMESTAMP_FORMAT = ''YYYY.MM.DD HH24:MI:SS''' the time format is not getting intialized but when i run the stmt ALTER SESSION SET NLS_TIMESTAMP_FORMAT = 'yyyy-mm-dd'; the time format is getting initialized.
SQL> CREATE OR REPLACE PROCEDURE set_date_format
2 AS
3 BEGIN
4 Execute Immediate 'ALTER SESSION SET NLS_TIMESTAMP_FORMAT = ''YYYY.MM.DD HH24:MI:SS''';
5 END set_date_format;
6 /
Procedure created.
SQL> insert into sili values('2003-05-23');
insert into sili values('2003-05-23')
ERROR at line 1:
ORA-01843: not a valid month
SQL> insert into sili values('2003-jan-23');
insert into sili values('2003-jan-23')
ERROR at line 1:
ORA-01843: not a valid month
SQL> insert into sili values('23-jan-2005');
1 row created.
SQL> ALTER SESSION SET NLS_TIMESTAMP_FORMAT = 'yyyy-mm-dd';
Session altered.
SQL> insert into sili values('2003-05-23');
1 row created.
SQL> insert into sili values('2003-jan-23');
1 row created.
Thanks & regards
Dinny

Help needed with "Time Machine could not complete the backup" because it is too large

I'm receiving "Time Machine could not complete the backup" because it is too large for the backup disk. I have a 500 GB Time Capsule 802.11n (2nd Gen) and a MacBook Pro running on 10.6.8. I just replaced my laptop's original hard drive with a new 1 TB and restored that with what was on my Time Capsule. Now, I have no backups on my Time Capsule prior to the new hard drive. When I click get info on my hard drive, it states only 296 GB of the 1 TB is used. However, the Time Machine error message states that the backup requires 315 GB but only 221 GB are available. It has deleted all of my old backups, so I would think my Time Capsule should have plenty of room to backup the 296 GB on my computer. Is my old backup from my prior hard drive stuck on the Time Capsule and instead of Time Machine trying to just update those files, it is preserving the old hard drive backup separately and trying to make a new backup of my new hard drive using the remaining space? If so, how do I fix this? Any advice greatly appreciated.

Have you read for possible solutions over in the "More Like This" thread over here?----------------------->
Research TM Knowledge Base Articles?

Help needed with Timer class

Hi there, could any body tell me if this is a bug with AS3
Timer class? Right now I'm developing a player with slow motion
capability using AS3, streaming from FMS3. Basically I used an
instance of Timer class to toggle play/pause at different
intervals. However, after doing some stress test (click slow then
play repeatedly fast), the flash player goes into a state in which
the video streams keeps going at slow motion and cannot be stopped
even with ns.close(). I called Timer.stop() whenever switching out
of slowmo and even removed the event. However as I was tracing it,
at the non-stoppable state, something is still calling the timer
and its handling function while Timer.running and
Timer.hasEventListener both returns false. I'm quite sure there's
nothing else that calls this specific timer handler.
Moreover, just out of curiosity, I changed my code and used
setInterval() method instead and the problem's gone. Would anybody
tell me if there's a bug with the Timer class or a bug in my own
code? I'm reluctant to go with setInterval() for good since Timer
class looks more elegant.
Thanks a lot!

Thanks, kglad! That was exactly my first thought. I made sure
I only used 1 timer object. Also, the strange thing is, the player
USUALLY works fine. It only breaks down after a a stress test I
described before. Any other suggestion on what I should do? Is
there a way to check who's dispatching the timer event?

NEED HELP BIG TIME!

I wrote a few days ago about this and was told that gathering
information from a form using Post as the method and having the
results emailed to someone wasn't a good idea and that it didn't
work very well. People basically told me to investigate scripting
or hiring someone, or use a pay service like MailChimp. None of
these are options for me right now, I absolutely have to get this
site done tonight and the person I'm doing it for will not pay for
a service.
The client wants to have a form on his site to collect email
addresses so he can compile them into a mailing list to send out
infrequent emails notifying people of upcoming events he's putting
on. He's a local artist with a very modest following, nothing big
time. I have no idea about databasing or MySql, and the person
doesn't want to pay for a service, so basically I'm stuck doing it
the "unreliable" way.
Can someone walk me through how to do this in Dreamweaver? I
assume I add a form field, and put a text field and submit button
inside of it. Here's my questions, to get this to work and use the
mailto: thing, what do I put for...
Form Field: Name, Action, Method, Target, Enctype
Text Field: Name
Button: Type, Name, ID, Value
Any help would be greatly appreciated by one stressed out,
hack web designer, thanks!

If this client doesn't want to pay for a service then tell
him the best
you can do is gather INDIVIDUAL emails from his site and have
them
emailed to their email address. Then it's up to them to mail
out to
their modest following INDIVIDUALLY.
Basically you put a form on the site to collect the email
address of the
user. Like this:
<form name="emailForm" method="post"
action="formmail.php">
<label for="email">Enter email
address</label> 
<input type="text" id="email" name="email"> 
<input type="submit" name="Submit" value="Submit">
</form>
You would then need to send the submitted form to a formmail
script
which will then send it on to the clients email address.
A free script named Formmail does exist if you search for it
in google
under Free formmail script
You would need to alter the script as per the instructions
which should
come with it and then upload it to your cgi-bin assuming you
have one on
your server.
You then point the form at the script by filling in the
action attribute
like:
<form name="emailForm" method="post"
action="
http://www.yourdomain.com/cgi-bin/formmail.cgi">
I no longer use formmail because it can be a bit of an issue
to set up
for beginners.
I now tend to use server side scripting like php to gather
the
information. IF you have php running on your server then
NateMail is
FREE and very very simple script to set up. It comes with
clear pdf
instructions that will do the job in about 10-15mins.
http://www.mindpalette.com/scripts/index.php#NMAnchor
xslamx wrote:
> I wrote a few days ago about this and was told that
gathering information from
> a form using Post as the method and having the results
emailed to someone
> wasn't a good idea and that it didn't work very well.
People basically told me
> to investigate scripting or hiring someone, or use a pay
service like
> MailChimp. None of these are options for me right now, I
absolutely have to
> get this site done tonight and the person I'm doing it
for will not pay for a
> service.
>
> The client wants to have a form on his site to collect
email addresses so he
> can compile them into a mailing list to send out
infrequent emails notifying
> people of upcoming events he's putting on. He's a local
artist with a very
> modest following, nothing big time. I have no idea about
databasing or MySql,
> and the person doesn't want to pay for a service, so
basically I'm stuck doing
> it the "unreliable" way.
>
> Can someone walk me through how to do this in
Dreamweaver? I assume I add a
> form field, and put a text field and submit button
inside of it. Here's my
> questions, to get this to work and use the mailto:
thing, what do I put for...
>
> Form Field: Name, Action, Method, Target, Enctype
>
> Text Field: Name
>
> Button: Type, Name, ID, Value
>
> Any help would be greatly appreciated by one stressed
out, hack web designer,
> thanks!
>

FCP HD Crash! Big time!

Hi all, could you please help. I am on MacBook Pro Duo Core 2.0 with 2GB RAM and running Mac OS 10.4.9. I had Final Cut Studio installed. The thing is, it crashes big time! Tried to start again and ot crashes again. Tried re-installing, but still crash. I run software updates and install FCP Update 5.1.4, Quicktime 7.5, and OS (Intel) updates, all successful except FCP 5.1.4. It said something about conflicting IDs or wrong key of some sort. Please help. I am getting really frustrated on this as I had my worked all stalled up because of this! I am not sure whether the problem is FCP, or Quicktime or the OS it self. Weird that problems only arises as they shifted to Intel processors. I tried running the video with Quicktime, but it crashes too.
Any idea? Help, please.

You probably need to delete your FCP license. Once gone, when you launch FCP, the program will ask you to fill in all the information again and should launch.
The license is located here:
/Library/Application Support/ProApps/Final Cut Pro System ID
good luck.
x

What happened to Big Time Moms

What happened to the latest episode of Big Time Rush? Sunday afternoon it was in the store and when I went to watch it it was the previous episode. When I went back to the store it was no longer available.

Thanks Jon, I appreciate the info.
I guess I saw a bit about that in the wikipedia but I still will have to figure out why audio isn't working in my FCS2 exports on this PC using this software.
cause I know its there in the final mpg but it just won't play.
anyone using media shout?
I have checked their website and their forum as well.... hopefully will get an answer there.
If anyone runs into this as well I can post my findings here as well.....
Thanks for the help.
DROCK.

Why does my audio quality drop big time when I use the compressor to compress my final cut studio project?

Hi,
When I'm working on a project, my audio sounds great but once I put my project though the compressor it looses it's volume big time when I play the DVD on a DVD player or computer. Where does the problem lie? How do I maintain the smae quailty of audio on the finished DVD?
thanks in advance,
Iki

You'll need to duplicate the Dolby Digital preset then alter the duplicate so that the DialNorm setting is -31dbfs and the Compression is set to NONE. Use the new, custom preset to create an ac3 file with the same output levels you had in your FCP Sequence.
-DH

My broadband wi-fi is chewing up MBs big time and I don't know why!

Hi everyone Since yesterday for some unknown reason my 4G broadband wi-fi is chewing up MBs big time from my laptop and I really don't know why! Even with the web browsers shut down, the broadband is chewing up at least 1MB per second and counting. Maybe it's a malware problem? I'm sure it's not a devious neighbour accessing the broadband because whenever I disconnect my laptop from the wi-fi, the wi-fi device stops chewing up MBs. So it's something to do with my laptop. I have a Sophos installed so I thought would have picked up any virus chewing up the MBs? Help anyone!

Has your laptop been downloading and updates? If you're using Windows, you can change the settings in control panel to stop it automatically downloading updates, you can choose which updates you want to install.
If Mac, I'm not knowledgable with Apple devices. I would recommend chatting with wireless Bigpond Tech Support on 13 39 33 "wireless"

BIG HELP NEEDED BIG TIME!!!!!

Similar Messages

Maybe you are looking for