Blank screen after installing K7T turbo and AMD 2000+ chip

Hello, I got a problem, can anyone help me figure this out.
Currently I changed my old motherboard and replaced it with a K7t Turbo2 Motherboard and I also bought a AMD Xp 2000+ processor chip to go with it.
After installation, I encountered numberous problems like:
1. The computer will only turn on and off by the power source box at the back of the computer.
2. The reset button doesn't reset the computer at all.
3. I keep getting a blue screen when entering windows xp (forgot what the message said, but said something like, it did that to help windows or something).
Anyways after that, I formatted the hard drive. Re-installed it with Windows XP. Once the installation was completed, it automatically reset, the computer. BUT insatead it just gave a blank black screen while the computer is still on(I can tell because I can still hear the heat sink fan blowing).
Next, I turned the power switch (on the back) off and on again. The computer did successfully booted and it brought me to the windows xp's Window. I then logged off from windows and now I have this problem:
When turning the computer back on, the computer will boot up, then a few seconds later (about 3 to 5 seconds) the computer will shut right off.
Any questions or answers will be great appreciated.

HI. What version bios are you running? If its 3.0, you need to update your bios in order to run the 2000XP. Are you sure that your case wires for the switches are in the right place? One way you might try to test the psu, is to close jumper j17, This will make the cpu run at 100fsb. If it boots ok at 100 fsb, Then your power supply is probably the culprit.With j17 open, the cpu runs at full power,133fsb, and it takes more power to run. BIGDADDY51 CT.USA J17 is located just under the memory slots. edit: you mean power off and on by power supply switch? This is normal. Then you should be able to push the case switch and have the computer restart.Check your case wires again.

Similar Messages

Fresh install of Exchange Server 2013 on Windows Server 2012 R2 Blank screen after install

Attempting to log in to the OWA I get a white screen immediately after entering credentials
When I open the Exchange Management Shell I get the error
+ New-PSSession -ConnectionURI "$connectionUri" -ConfigurationName Microsoft.Excha ...
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : OpenError: (System.Manageme....RemoteRunspace:RemoteRunspace) [New-PSSession], PSRemotin
gTransportException
+ FullyQualifiedErrorId : AccessDenied,PSSessionOpenFailed
Along with the above error it also says Access is denied
Im running the Exchange shell as admin
There were no errors during the install and I did everything according to the Exchange Server Deployment Assistant
At first when I attempted to log in it would say my credentials were incorrect
This is part of a active directory set up and I fulfilled all of the active directory piece.

Hi,
According your post, I understand that open EMS with error “AccessDenied,PSSessionOpenFailed” after fresh install Exchange 2013.
If I misunderstand your concern, please do not hesitate to let me know.
Please follow below steps for troubleshooting:
1. Reboot the server, usually fixes this error.
2. Make sure your authentication settings on your virtual directory for PowerShell is correct.
Internet Information Services (IIS) Manager, <Servername>, Sites, Default Web Site, PowerShell and in the right panel, scroll down to the Authentication module, then make sure that Anonymous access is disabled and Windows Authentication is
enabled.
3. Double check the configuration of HTTP binding on Default Web Site in Internet Information Services (IIS).
4. Run Get-User Identity | FL *power* to check whether the current logged in user has remote powershell enabled.
If the issue persists, please try to remove the PowerShell virtual directory and renew for testing.
Additional, I find an similar thread about your question, for your reference:
https://social.technet.microsoft.com/Forums/windows/en-US/29b3284a-36e1-43b0-87b8-63ee4500f265/exchange-2013-ems-throwing-access-denied-error-and-toolbox-giving-mmc-error?forum=exchangesvradmin
Thanks
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]
Allen Wang
TechNet Community Support

Blank screen after installing new RAM

I have a 1.5 Ghz, 512 DDR SDRAM and it's starting to get sluggish so I bought 1GB DDR 333MHz RAM and replaced the samsung card inside. When I start up you can hear the chime but the screen is blank. When I put the old card back in it works again.
Anyone any ideas how to resolve or have I bought dodgy/cheap/wrong RAM?

Welcome to the Apple discussions.
Does the Samsung memory have the same label or BNO number on it as http://eshop.macsales.com/item/Samsung/27SAMSO1GB/ ?
Samsung is one of several brands that generally work fine in our Powerbooks.

PC fails to reboot and shows blank screen after automatic windows updates including SP

Pavilion- a1130n" WINXP ProfessionalC fails to reboot and shows blank screen after automatic install ing windows updates including SP 3

I would love to say that a refresh worked for me however it did not.It takes about 30 Minutes total I was able to trace part of the issue to a Registry Key that was tagging the processor. Because my BIOS manages its own temp gauge and windows is trying to
build on in I had to turn the BIOS one off as well as for some reason I get better funtionality with Visualization off.
I am still dealing with a lag but I was able to get ride of the freeze that made the computer completely useless.

K7T TURBO and GeForce 4600

Hello all,
I am having trouble trying to put together my K7T TURBO MS 6330 with an ASUS V8460 (Ti 4600 Ultra Deluxe).
Specifically, I just replaced my old Oxygen card with the GeForce 4 one, and as soon as I installed the SmartDoctor 2 utility, I got the message (in red flashing text) :
" Your VGA card voltage 1.5 is out of safe bound. Motherboard doesn't supply with reliable
1.5 voltage.
Please contact with motherboard manufacturer for help."
(I've allready sent an email to MSI support, and still waiting.)
Furthermore, I've been experiencing sudden crashes (i.e. when I am using 3d applications) followed by a blue screen reporting an error message about a file that seems to belong to SmartDoctor folder.
I've read that ASUS vga cards are rather demanding as for power and voltage. Anyway, I'd like to ask everyone in the forum, if there is a safe and reliable way for the
K7T TURBO and the Ti 4600 to work together, perhaps with a motherboard BIOS update (I am still using ver. 2.7 since there was no need to flash it till now) or something...or maybe it would be a better thing to do, to install on my machine an MSI 4200 8x AGP card that is available, instead... or ... go back to my oxygen thingie... :(
My PSU is 420 Watt, and my cpu is Athlon 1200 with 768 mb ram.
Well, I just hope someone could help...
Thanks in advance

Hi all,
I forced my AGP bus to x2 a couple of minutes ago, and now I got a message from Smart(...) Doctor that my voltage is out of 3.3 V bound etc.. and a blue screen reporting UNEXPECTED KERNEL MODE TRAP (?).So, the situation is not improved...
I also put my sound card to another PCI slot, but I still had no luck at all. The thing is that unfortunately I have IRQ 11 being used by 6(!) devices: my gfx card, my scsi controller, my soundblaster, 2 VIA USB controllers and Microsoft ACPI Compliant System.Not very nice indeed.
I wonder if updating the motherboard's BIOS would do any good; btw, mine is ver.2.7, while the latest is 3.6 (!), but since I was ok till now, why bother flash it?
For the time being, I am not able to run 3D Mark 2k1 beyond benchmark #3, since it stops, leaving me on the desktop, while whenever I run Maya, winamp 3 and ACDSEE 4 simultaneously,after a while I get the blue screen of death, saying something about anvioctl.sys file - a SmartDoctor file hiding into system32/drivers. ?(

Blank Screen after starup (like uploading but not)

Hi and help please. I own a 27in Mac. It has been receiving all updates and it has been working perfectly. This afternoon, I start it up, a status bar appeared , and then a small rotating circle indicating some sort of processing. I assume and update was being made. After one hour, and checking my internet connection (3.5MBps) I saw no change. I restarted and situation is the same, no change at all except the blank screen with the grey apple and circle indicating status of some process.
I inserted the CD Rom with Snow Leopard to try to affect it somehow, but the disk is not uploading. You can hear some HDD noices in the beginning, but then they stop.
Please any clue or tip to make it work normally again.
Francisco.

If you have the drive backed up, erase the drive first with your Disk Utility and then do the install.
Dave M.
Check out the new remodeled MacOSG website! 24-hour Apple-related news & support.
 MacOSG: An Apple User Group  iTunes: MacOSG Podcast  Follow us on Twitter: MacOSG

Blank screen after KitKat update

I just completed the KitKat update on an Ellipsis 7 tablet that's connected to Verizon's network, but now I'm only getting a blank screen after the welcome screen displays. Fyi: the first part of this update went smoothly. Can anyone can help me resolve this issue? I really like this tablet and use it everyday.

I contacted Verizon support and a couple of techs attempted to walk me through alternate boot methods. However, as bassclarinetl2 noted, "pressing the power button to turn the device off results in the device powering up by itself and both 'safe mode' and 'factory reset' are inaccessible via their button combinations." Therefore, I'm sending my tablet in to be repaired or replaced under warranty. Depending on how long you've had your Ellipsis 7 tablet, you may be able to do the same.
Incidentally, I have another (seemingly) identical Ellipsis 7 tablet and was able to successfully install the KitKat upgrade on this second tablet, which I'm using now. The sooner Verizon determines why the upgrade worked on one tablet and not the other, the better.

BLANK SCREEN AFTER WINDOWS 7 LOGIN

Hi, I am getting a blank screen after i login. -I have no available restore points-safe mode works fine-Explorer.exe works but some programs play up and i dont really want to do a clean install Please help !

Same problem I've found a solution.
#1 Hit fastly 5 time the left shitf button on your keyboard.
A windows will appaers to know if you want to caps lock. Keep it open
#2 Alt-CTRL-Del
You have know your desktop
#3 Go on add-remove programme
3a) Go on windows add-remove
3b) Remove internet explorer
ok-ok-ok - untill it's remove and ask to restart
#4 No more problem. You have to go on the net with chrome or firefox.

Blank Screen after 703HP3 (Linux)

Hi,
after update a VMWare-SLES10SP2-Server with DOM and Webaccess HP703HP1 to
HP703HP3 I got a blank screen after starting the machine.
All logs look got but I can't login in. Only a blank web page. No login. No
picture. Nothing.
Any idea?
Have anybody the same problem?
I went back to my snapshot. So my user can login.
Now I will try it at another server.
Andreas

Hi Massimo,
the login web page for webaccess for the user...
Andreas
"Massimo Rosen" <[email protected]> schrieb im Newsbeitrag
news:[email protected]..
> Hi,
>
> Andreas Schild wrote:
>>
>> Hi,
>>
>> after update a VMWare-SLES10SP2-Server with DOM and Webaccess HP703HP1 to
>> HP703HP3 I got a blank screen after starting the machine.
>
> What do you mean "a blank screen"? A blank screen where?
>
>> All logs look got but I can't login in. Only a blank web page. No login.
>> No
>> picture. Nothing.
>
> I'm sorry, but it's totally unclear what you're talking about. What web
> page?
>
> CU,
> --
> Massimo Rosen
> Novell Product Support Forum Sysop
> No emails please!
> http://www.cfc-it.de

Blank Screen after Hibernate

Hi,
On my DV6-3085 I sometimes power up by opening the lid and get a blank screen after a few seconds.
The screen will say Starting Windows, flash and then go blank. At this point the finger print scanner is still working and responds but you cannot obliviously see anything.
I fairly suspicious this happens after the laptop has not been used for a little while (overnight) after a lid close, so the Sleep light has stopped flashing and the laptop is in hibernate mode.
My guess is it is something to do with switching graphics adapters. I've not yet decided if plugging the power in first does or does not make a difference or being on battery or AC when the lid was closed.
I've got the latest drivers according to the HP driver update utility.
Anyone with the same problem or have a solutions?
Thanks,
Dean.

Hi,
On my DV6-3085 I sometimes power up by opening the lid and get a blank screen after a few seconds.
The screen will say Starting Windows, flash and then go blank. At this point the finger print scanner is still working and responds but you cannot obliviously see anything.
I fairly suspicious this happens after the laptop has not been used for a little while (overnight) after a lid close, so the Sleep light has stopped flashing and the laptop is in hibernate mode.
My guess is it is something to do with switching graphics adapters. I've not yet decided if plugging the power in first does or does not make a difference or being on battery or AC when the lid was closed.
I've got the latest drivers according to the HP driver update utility.
Anyone with the same problem or have a solutions?
Thanks,
Dean.

HT1386 I just got an iphone 4 and when I go to sync it, it appears in the left hand column but when I click on it there is just a blank screen with the apply logo and a tiny lock.

I just got an iphone 4 and when I go to sync it, it appears in the left hand column but when I click on it there is just a blank screen with the apply logo and a tiny lock.

OK, I think I fixed it.
After trying to restore with an old backup from the phone (it estimated it would take 4 hours) I cancelled and went through the setup menus again, but set it up as a new phone. It then appeared in iTunes and I restored it from the computer, not the phone. It appears to be working, it's syncing my old apps right now.
Summary:
1. Reset settings on phone (hopefully you backed up fairly recently)
2. Set up as NEW iPhone in setup menu on phone
3. Restore from iTunes on computer when it recognizes the phone
4. Cross fingers

Laptop only coming up with a blank screen after set-up?

Ok, so. My parents bought me a brand new hp laptop for christmas. On christmas day i went through the whole set-up process and did all the steps it told me to do. When i'd been through all the steps, i got a loading symbol and ever since, all it comes up with is a blank, black screen and a mouse icon that i can move. I'm not 100% sure of the model though (appologies). What do i need to do??
Cheers

Hello @15_,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how your notebook is coming up with a blank screen after setting it up. Is the power on the computer on? Is there an error message on the screen? I would be happy to help you, but first I would encourage you to post your product number for your computer. Below is a is an HP Support document that will demonstrate how to find your computer's product number. In addition, it will also help if you indicate which operating system you are using; and whether your operating system is 32 or 64 bit. The more information you can provide, the better!
How Do I Find My Model Number or Product Number?
Which Windows operating system am I running?
Is the Windows Version on My Computer 32-bit or 64-bit?
Please re-post with the necessary information, this way I will be able to research this further for you. I look forward to your reply!
Cheers!
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Can't burn blank CD after installing CD that came with ipod nano

Can't burn blank CD after installing ipod software - I have the system prefs set to launch Toast 6 when inserting a blank disk, and the drive just churns and then ejects the CD. It mounts and runs burned music and data disks with no problem.
My job requires me to burn data disks from pictures I take at work. Should I re-install Toast? The OS? I ran Disk Utility to check/fix permissions, and no change.

The CD that came with the nano won't have anything on it that you won't get with a full iTunes install. In fact, it may have been an OLDER version of the iTunes software than what you had installed before.
I'd reccomend downloading the latest version of iTunes from Apple and installing that to rule out software reversion issues.
If the problem still exists, try booting into toast before inserting the blank disk and see if Toast can still burn to the CD. If it can, then odds are you have to re-instruct your computer to boot toast when a blank CD is inserted. If it can't see the blank CD, or the Finder spits it out again, then I think you'd have to re-install Toast.
Doc

Occasionally flickering iMac screen after installing Yosemite

Occasionally flickering iMac ()intel) screen after installing Yosemite. Cannot yet specify when the flickering occurs, but it cover large sections of the screen. Absolutely annoying.

I also have this issue but only below 6 screen illumination steps (bars)
This flickering issue is active after waking up from sleep os screen sleep and if I increase the screen light to a setting higher than 6 screen step for a wile (30 seconds or so) and the reduce the light to a level below 6 steps it usually holds on without flickering.
This happens on an late 2009 iMac with nvidia card running OS X 10.10 and apple later upgrades but not (until now) on another same age and OS X version iMac I have but instead of the nvidia card it has an ATI
Question:
Has anyone tried to use the Mavericks nvidia graphic card driver with Yosemite?

Bootcamp goes blank screen after startup sign.

I'm unable to start up my bootcamp. It just goes blank screen after the startup moving icon and stays blank screen. Can anyone help? Thank you in advance!!!

@MT1
‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
If you are unfamiliar with the Forum's private messaging please click here to learn more.
Thank you,
Omar
I Work for HP

Blank screen after installing K7T turbo and AMD 2000+ chip

Similar Messages

Maybe you are looking for