Boot Camp - "No AMD graphics driver is installed" error during win8.1 post-install

I have Macbkook pro early 2011 (i7 2.2ghz, 16 GB RAM, radeon 6750M 1GB)
I used boot camp utility to install win 8.1 - it completed without any problems.
When the installation was completed the bootcamp wizard opened automaticaly and this was shoved to my face:
The process continued until the "Installing Intel Graphics" process. Then the screen just went blank. I waited some time
assuming it was just a gpu driver issue and the installation is progressing. I guess I was right since the mac rebooted after about 5 minutes.I re
When I wanted to boot to windows I was constantly welcomed by black screen after the "windows splash-screen-spinning-animation thingy".
I went to safe mode to see what's going on. It turned out that if I TURN OFF my INTEL HD 3000 driver then I can boot to normal mode but
the 6750M drivers have yellow exclamation mark (error 43 in details) in device manager. I need that gpu enabled since I do some game developent which requires gpu power. I tried reinstalling ati drivers and looking for new ones on the internet - each of them failed. What could be the problem?
Can anyone help me out?

Hello HPENVYm6-1201TX,
I have read your post on how your notebook computer is producing an error message in regards to your AMD driver, and I would be happy to assist you in this matter!
To ensure that the software is installed and functioning properly, I recommend performing a clean boot on your notebook. To do this, please follow this document on How to perform a clean boot in Windows. This should help eliminate software conflicts that occur when you install a program or an update or when you run a program in Windows.
The next step I suggest is to remove the AMD driver installed on your computer, and install the driver provided on HP's website. If you need to, you can use this document on how to remove software from Windows 8.1. You can find the necessary driver by click on the AMD High-Definition (HD) Graphics Driver.
Instead of updating the driver from AMD's website, please follow this document on Using HP Support Assistant (Windows 8) to update the necessary drivers.
Please re-post with the results of your troubleshooting, and I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Similar Messages

17" MacBook Pro Core i5 Boot Camp Nvidia 64 bit driver install issue

Can't get correct Nvidia driver to install on 17" MacBook Pro core i5. Windows 7 64 bit is installed and running but its using a standard VGA driver for the video card so the full resolution of the display is unatainable. I've loaded the snow leopard windows 64 bit drivers, downloaded the BootCamp 3.1 64bit drivers and installed but each time I try to run it the Nvidia part of the installer closes with the error, you are trying to use a 32bit uninstaller for a 64bit program, and it exits. I've double checked to make sure I have the 64bit driver installer instead of the windows 7 32bit installers but I still get the error every time. I then downloaded Nvidias own driver for windows 7 64bit Gt 330M and it gets the same error. Please help?

A number of people in this and other forum threads have reported problems with the Nvidia drivers when installing Windows 7 (64bit) on the new Macbook Pro (April 2010).
The problems appear to be due to an installation of Boot Camp 3.0, followed by the update to Boot Camp 3.1. As Boot Camp 3.0 does not include the Nvidia graphics drivers for the
Macbook Pro 2010, the graphics card is not recognized and the subsequent update to Boot Camp 3.1 does not complete successfully.
The proper approach consist of installing Boot Camp 3.1, which is included in the system disk that shipped with the laptop. A copy of that version was posted e.g. here
http://files.me.com/jason_fearing/an51fn. One should not use on the Macbook Pro 2010 the Boot Camp version 3.0 that shipped with the original DVD of Mac OS X Snow Leopard.
I had the same problems that were reported in the forum, when installing Boot Camp 3.0 + Boot Camp 3.1 update on Windows 7 (64bit). First I had to manually run the 64bit Boot Camp setup, as suggested by others, and then I had to install the Nvidia drivers with the modified INF files from http://www.laptopvideo2go.com/, as the graphics card was not recognized.
However when I used the proper Boot Camp 3.1 that came with the laptop, everything went completely smoothly and the installation consisted of just clicking on the setup file.

Installing boot camp on a second drive

Hi All,
First let me apologize for this long-winded post and also for my lack of basic knowledge when it comes to mac computer skills.
I would like to install windows 7 on a brand new 500gb drive in a brand new mac pro.
I was reading through the installation & setup up guide for boot camp and was stonewalled on page 6 it says;
“If your computer has more than one internal disk and you want to install Boot Camp on a disk that isn’t in the first hard drive bay, remove the drives in the lower numbered bays. You can reinstall the drives after you install Boot Camp.”
Ok that makes sense but if I remove the first drive how do I install boot camp since the first drive contains boot camp on it?
The next question I have is; Can I make the whole 500gb drive one partition that will have boot camp, windows 7 and all the windows files on it or does it have to have just boot camp and windows 7?
Thanks
Mike

Shutdown - pull OS X drive(s) - continue with install.
You'll have to change to NTFS when you get to where to install.
At that point you can even format or partition.
As for the Assistant, well, some install Windows 7 on a drive without it (that can't be done with XP) and just leave one drive and boot from Win 7 DVD.
"that will have boot camp...."
There IS NO "boot camp." The assistant modified the partition table to include a standard MBR for booting Windows. And that would be on the #2 500GB.
Until you install the Apple setup.exe drivers and services after Windows is installed from your OS X DVD, there is nothing in or on Windows that is faintly about boot camp. Unfortunate term. It also gets to become a control panel in Windows to change the default startup OS (why not call it Apple OS Switcher / Apple Startup Disk).
There will be AppleTimeServices and AppleOSSwitcher services along with HAL and device drivers to enable them in Device Manager.
As for lowered numbered and first drive bay, they must think Mac Pro owners are locked into and only boot from drive bay #1. and that Assistant is a very limited not very smart partitioning tool is true.
So run Assistant but instead of restarting with the DVD and install, just shutdown. Pull all the other drives but 500GB. Then boot off the DVD.

HP Pavilion g6-1301tx Notebook PC/ Not able to install AMD graphic driver.

My HP Pavilion g6-1301tx Notebook PC 4gb RAM is 2 years old,My original OS was Windows 7 Home basic 64 bits then i changed it to Windows 7 Ultimate 64 bits.
ERROR......................
In device manager under display adapter there are two GPUs i.e. Intel Hd graphics 3000 its alright and Standard VGA graphic adapter which contains error (this Device cannot start code 10). I tried to update the driver in device manager itself but it tells ( Windows found the driver for the device but unable to install), I even tried windows update there it shows the driver update but whent i try to install it shows error Code 80070002.
Because of this im unable to play games and watch hd videos in my laptop.
Please some one help me to solve this problem.

Hi:
The only graphics driver you should install for your model is the AMD graphics driver which will install both the AMD and Intel GPU's.
If you installed the Intel graphics driver from your PC's support and driver page, that could be preventing the correct AMD driver from installing.
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-99756-1&cc=us&dlc=en&lc=en&...

Installing AMD graphic driver turns into BSOD

Hello, I have recently reinstalled Windows on my laptop and now i can't install AMD graphic driver. Whenever I try to install it, my screen switch off ( as usual during installing of graphic driver) and then turns into BSOD with error "atikmpag.sys". After this, I am unable to switch on my computer, because there is always BSOD waiting for me and I have to reinstall windows again. This is happening with Win 8.1 and with Win 7. I have tried many versions(releases) of drivers and many ways to install them. But the result is always the same: BSOD "atikmpag.sys".
Could u give me any solution for my problem? It is really frustrating. I am not very used to write in English, please excuse me. Regards, Patrik Obrtlík

AMD's 'catalyst clean utility' (stand-alone program) is notoriously bad, yes especially for switchable graphics laptops. And have heard some horror stories of that ruining windows installations needing a reinstall DDU, I would argue is perfectly safe however. It is pretty universal generic clean utility which can clean both AMD and Intel components. I use it myself(HP envy 15 with AMD+Intel), though AMD catalyst install manager (from 'uninstall or change programs' list) would work, though I don't think it cleans/removes Intel installations.

'No AMD graphics driver is installed..'

Hi, I've recently been receiving this message 'No amd graphics driver installed or is not functioning properly. Please install the amd driver appropiate for your amd software' on my pavilion dv6 and I'm not sure why? When I look in the Device Manager under Display adapters there are 2 graphics cards showing - AMD Radeon HD 7400M Series (which has the following device status 'Windows has stopped this device because it has reported problems. (Code 43)' which I assume is where the problem lies and the other one is ATI Mobility Radeon HD 4200 Series which has the device status 'No drivers are installed for this device.' I have tried disabling each one and looking for updates but nothing seems to work. I recently upgraded to Windows 10 from Windows 7 but the issue was there before the upgrade. Any help would be much appreciated!

Then you should not do it by yourself, find a friend who knows what the BIOS is and how to reset it to its default settings and request him/her to help you

Boot camp on mini requesting driver during install

, have tried looking at all drivers on memory stick but won't accept any of them. using a suitable image and memory stick ceated with boot camp.

This is the screen I get when I start to install windows

About boot camp with multiple hard drives.

Hi folks. I've just ordered my new 27" iMac. It has the 256GB SSD and i'm wondering about using boot camp on the system.
I understand that OSX will come installed on the SSD, what I was wondering however, is that if I would be able to use boot camp to install windows on the standard 2TB HDD that comes with it.
Secondly, if thats possible, is it possible to switch the 'standard' system bootup from Windows to OSX as you desire?
I owned a MacBook Pro recently which had Windows 7 installed, however after I installed that, it would boot windows automatically unless I used the Alt key on startup to choose OSX instead.
What i'm worried about is that after I install Windows 7 again, that it will boot into Windows as standard, then i'll need to hold Alt and choose OSX instead, which is going to take some time, and totally cancel the benefits of having an SSD for quicker start up times.
So can you switch the standard bootup operating system once installed?
Thanks for reading.

Yes, Boot Camp can be used on any internal drive. To alter startup behavior use the Startup Disk preferences to set your OS X volume as the permanent boot volume. When you want to boot Windows use OPTION boot - restart and after chime press and hold down the OPTION key until the boot manager appears. Select the Windows volume then click on the large downward pointing arrow button. When you next restart the computer it will automatically return to OS X.

"Booting from Boot Camp Assistant created USB Drive...Failed to load BOOTMGR"

Hi Apple Ppl of the Wrld: I need help I been working on installing windows 8 on my Mac.
Spec of equipment:
Mac Book Pro Mid 2012
Bootcamp Version: Version 5.0.4 (473)
Bootable USB Flash Drive: Type Scan disk 4 GB windows 8 pro iso image but without the driver and the 2nd Scan disk USB flash drive with 32 GB with the Bootcamp Drivers downloaded and saved to this drive.
Please Note: I also have the original back up installation disc for Microsoft 8 Prof 64 from Microsoft where I purchased it from.
1st Bootcamp is not recognizing the Original Microsoft 8 Pro backup disk from microsoft itself.
Solution: I created the New Image from the Original Microsoft installed disc in my desk top and changed the extension to .ISO then burned the ISO image into the newly purchased DVD+R. Then I ran Bootcamp Once again and it get the following error message "The installer disc could not be found -- Insert your Windows installer disc and wait a few seconds for the disc to be recognized. Solution
2: Created a bootable usb drive with bootcamp assistant successfully with bootcamp. Yes I close, ejected or un-mounted any image that was open or had been previously used then i restarted the Mac. Next, I start the bootcamp assistant tool once again then i get the same insert your windows installer disc message.
3: Then I try to resolve the installer disc not found issue: this are the steps i took: a). Lauch disc utilities
    1. Selected the top most drive 750 GB Macintosh HDD
    2. On the right you’ll see 5 tab buttons: First Aid | Erase | Partition | RAID | Restore.
    3. Choose Partition. Then I clicked + to add another partition size of the partition was 222 GB
    4. Change the Name of the Partition to BOOTCAMP
    5. Change the Format to MS-DOS (FAT)
    6. Click Apply to save the changes and then reboot your Mac and we’ll begin Windows installation.
    7. During reboot, press and hold the alt/Option key and you’ll be presented with drives to boot from.
    8. Use the arrow keys and return button to select the Windows yellow USB key drive containing your Windows 8 installation files.
    9. This will begin the Windows install. --> then i get the following message: "Booting from Boot Camp Assistant created USB Drive...Failed to load BOOTMGR".
4: Take the Mac to best buy and let them resolve the issue and charge me like a million dollars for it :'( since i have no other idea who to get this bootcamp working at all. This has been a terribly lengthy issue and it is not as simple as it is claimed to be since i started with the Original Windows Disc Purchased from Microsoft and I have the Optical disc drive which it should be simpler from what I understand.
Please can you help It would be of great help.
<Email Edited by Host>

from what i understand you are trying to install win 8 pro from a "backup disk" the one that you purchased from microsoft.
this will not work, it is not an installer disk.
you need to start the process again. erase the partition you made on your hdd. in disc utility click the minus button after selecting the bootcamp partition, then manually drag the divider down fully then apply.
next, erase your usb then format it.
download win 8 iso from here;
http://getintopc.com/softwares/operating-systems/download-windows-8-pro/
it is perfectly legal to use your purchased product key in this install.
in bootcamp select the iso image you just downloaded, select your preferred partition size, check all 3 options.
you have the support software on another usb but you wont need it so it can be discarded. the install will work far better with the iso and support on the same drive.

Boot Camp For Lion -- USB ISO Method --"Booting from Boot Camp Assistant created USB Drive...Failed to load BOOTMGR"

Hello, has anyone had experience with dealing with this speciifc problem?
In short, upon rebooting, I am getting a black screen with a line of text that says, "Booting from Boot Camp Assistant created USB Drive...Failed to load BOOTMGR." Nothing happens after that.
I am using Mac OS X Lion 10.7.4. I have an ISO of Windows 7 Prof. along with an 8GB usb drive. I changed the coding in my bootcamp program to allow for the normally first invisible option that allows creation of a USB Installation program using an ISO that is normally only for computers without an optical drive.
I have that box checked, the check for new software box, and the install windows box checked. I went through the process of creating the USB, downloading the software, and partitioning the drive. Then on restart, I get the failed to load bootmgr error.
Some people have suggested using two usb drives for this. I am trying that method but it does not seem to help thus far.
Can anyone offer any help?
Thanks.

from what i understand you are trying to install win 8 pro from a "backup disk" the one that you purchased from microsoft.
this will not work, it is not an installer disk.
you need to start the process again. erase the partition you made on your hdd. in disc utility click the minus button after selecting the bootcamp partition, then manually drag the divider down fully then apply.
next, erase your usb then format it.
download win 8 iso from here;
http://getintopc.com/softwares/operating-systems/download-windows-8-pro/
it is perfectly legal to use your purchased product key in this install.
in bootcamp select the iso image you just downloaded, select your preferred partition size, check all 3 options.
you have the support software on another usb but you wont need it so it can be discarded. the install will work far better with the iso and support on the same drive.

Understanding boot camp and formatting backup drive for it

somehow i never got to fully understand how boot camp works in relation to OS X and i am wondering if someone can help me out here.
1. can i install boot camp on a mac pro and have NO mac OS on the computer at all? i have an old install here on a drive that i am not using and my recollection is that this is what i was doing.
2. if this is the case do i simply BACKUP this Boot Camp OS to an external drive that is formatted for windows?
3. if i have another newer mac pro (as I do) - and i am running yosemite on it - can i just run an partition on this drive and install my Boot Camp install (or maybe i run the boot camp installer and it creates a partition for itself)?
4. in the PAST i used WinClone to create a BACKUP of the Boot Camp installation and simply dropped this backup on my OS X desktop which was backed up. is there any good reason for me to PARTITION the backup drive with a part of it being /partitioned/ as windows drive so that the Boot Camp Partition was backed up to this windows partition? the lacie external drive install app seems to ask if i want to do this and i got to thinking there may be a more direct way to backup BOOT CAMP than running the WinClone backup manually once in awhile and having this image backed up with the rest of the OS X partition.
thanks for any help.

thanks Csound. this is a tad confusing for me.
i guess hatter is saying he would like to see the Windows 7 boot camp on its own drive. and right now i am basically planning on /restoring/ the WINCLONE image backup from my 2006 MP to either this separate drive in bay 4 in the 2012 MP or a partition on the OS X drive in bay 1 (if i can "cleanse" it of all the stuff it had when it was on my older 2006).
i guess i do this /through/ the WINCLONE user interface but is it going to somehow drop this boot camp partition on a separate drive that somehow has its /own/ mac OS install on it? you know what i mean? i mean - say i want to put this boot camp install on an empty drive in bay 4, so i format it with extended journaled and then go into winclone and start some kind of restore procedure of my backup to that drive? i guess i am confused big time about this.
also, just so i am clear. is that 2 partitions per mac pro or per disk? i mean, i do have an OS X yosemite on my drive and i am planning on installing windows 7 by restoring from WinClone image

BOOT CAMP and AMD Radeon HD 6750M - NO EXTERNAL DISPLAY

Hello,
I have a MBP 15' with the new AMD Radeon HD 6750M display card.
If I run WIN 7 64 bits with Boot Camp and the current driver I cannot connect a projector or external monitor.
It runs normally wit MAC OS.
Is there any solution for this??
Thanks,
Rodrigo

seemed to work...

Install EBS R12 Problem - Post Install Checks

Folks,
Hello. I am installing EBS R12 using "rapidwiz".
The Install Wizard almost finishs installing and gets to "Post Install Checks". The message is as follows:
Validate System Configuration:
Database Availability
Environment File
HTTP
Virtual Directory
Login Page
Configuration Upload
DBC File
Help Page
JSP
Each of the above items gets an error message.
When click "next" button in the Wizard, the messgae comes up as follow:
"Rapid Install Wizard has detected that your configuration has errors. You must resolve these issues before continuing."
Can any folks tell me how to solve these "Post Install Checks" errors ?

Please i need help with this post Installation errors below(8 in number), am running the installation on windows 7, i used perl to stage my files, installed cygwin instead of MKS toolkit, run my installation without no errors but when i got to post-Innstall ckecks, i got the following errors
1. Database Availability
command: cmd.exe /c C:\u01\StageR12\startCD\Disk1\rapidwiz\bin\riwTDBup.cmd c:\oracle\VIS\db\tech_st\11.1.0\VIS_hakonix-pc.cmd sqlplus C:\u01\StageR12\startCD\Disk1\rapidwiz\bin\riwTDBup.sql APPS/APPS
C:\u01\StageR12\startCD\Disk1\rapidwiz>echo off
Tue 01/17/2012
11:15 PM
"Cannot find environment file "c:\oracle\VIS\db\tech_st\11.1.0\VIS_hakonix-pc.cmd""
ERRORCODE = 0 ERRORCODE_END
Database ORACLE_HOME connection test has succeeded
command: cmd.exe /c C:\u01\StageR12\startCD\Disk1\rapidwiz\bin\riwTDBup.cmd c:\oracle\VIS\inst\apps\VIS_hakonix-pc\ora\10.1.2\VIS_hakonix-pc.cmd sqlplus C:\u01\StageR12\startCD\Disk1\rapidwiz\bin\riwTDBup.sql APPS/APPS
C:\u01\StageR12\startCD\Disk1\rapidwiz>echo off
Tue 01/17/2012
11:15 PM
"The environment settings are as follows ..."
" ORACLE_HOME : c:\oracle\VIS\apps\tech_st\10.1.2"
" ORACLE_SID : "
" TWO_TASK : "
" PATH : c:\oracle\VIS\apps\tech_st\10.1.2\bin;c:\oracle\VIS\apps\tech_st\10.1.3\appsutil\jdk\bin;c:\oracle\VIS\apps\tech_st\10.1.3\appsutil\jdk\jre\bin;C:\app\hakorlc\product\11.2.0\dbhome_1\bin;C:\Perl\site\bin;C:\Perl\bin;C:\OraHome_1\bin;C:\OraHome_1\jlib;C:\Windows\system32;C:\Windows;C:\Windows\System32\Wbem;C:\Windows\System32\WindowsPowerShell\v1.0\; c:\oracle\client"
" LD_LIBRARY_PATH : c:\oracle\VIS\apps\tech_st\10.1.2\lib"
SQL*Plus: Release 10.1.0.5.0 - Production on Tue Jan 17 23:15:55 2012
Copyright (c) 1982, 2005, Oracle. All rights reserved.
ERROR:
ORA-12541: TNS:no listener
connect test returning code 1
ERRORCODE = 1 ERRORCODE_END
RW-50011: Error: - Apps ORACLE_HOME connection test has returned an error: 1
2.Configuration Upload
uploading config file at C:\oracle\VIS\db\tech_st\11.1.0\appsutil\conf_VIS.txt
Failed upload of config file at C:\oracle\VIS\db\tech_st\11.1.0\appsutil\conf_VIS.txt
3. Environment File
RW-50016: Error: - Database ORACLE_HOME environment file was not created:
File = c:\oracle\VIS\db\tech_st\11.1.0\VIS_hakonix-pc.env Apps ORACLE_HOME environment file passes instantiated variables test:
File = c:\oracle\VIS\inst\apps\VIS_hakonix-pc\ora\10.1.3\VIS_hakonix-pc.cmd
iAS ORACLE_HOME environment file passes instantiated variables test:
File = c:\oracle\VIS\inst\apps\VIS_hakonix-pc\ora\10.1.2\VIS_hakonix-pc.cmd
APPL_TOP environment file passes instantiated variables test:
File = c:\oracle\VIS\apps\apps_st\appl\VIS_hakonix-pc.cmd
ADOVARS environment file passes instantiated variables test:
File = c:\oracle\VIS\apps\apps_st\appl\admin\adovars.cmd
APPSCONFIG passes instantiated variables test:
File = c:\oracle\VIS\apps\apps_st\appl\admin\adconfig.txt
4. HTTP
checking URL = http://hakonix-pc.www.hakonix.com.ng:8000
RW-50015: Error: - HTTP Listener is not responding. The service might not have started on the port yet. Please check the service and use the retry button.
5. Help Page
checking URL = http://hakonix-pc.www.hakonix.com.ng:8000/OA_HTML/help
RW-50015: Error: - Help Page is not responding. The service might not have started on the port yet. Please check the service and use the retry button.
6. Virtual Directory
RW-50015: Error: - Http Server Virtual Directories is not responding. The service might not have started on the port yet. Please check the service and use the retry button.
7. JSP
checking URL = http://hakonix-pc.www.hakonix.com.ng:8000/OA_HTML/jtfTestCookie.jsp
RW-50015: Error: - JSP is not responding. The service might not have started on the port yet. Please check the service and use the retry button.
8. Login Page
RW-50015: Error: - Login Page is not responding. The service might not have started on the port yet. Please check the service and use the retry button.

Why the Oracle 8.1.7 PE coundnot have error during start the install stage On Win98?

Why the Oracle 8.1.7 PE coundnot have error during start the install stage On Win98?Someone tell me that need one patch for win98,but where can I download it?
Thanks

Why the Oracle 8.1.7 PE coundnot have error during start the install stage On Win98?Someone tell me that need one patch for win98,but where can I download it?
Thanks

Which client should I choose when i do client copy during PI post-install?

Hi,gurus:
Which client should I choose to be the source client when i do client copy during PI post-install?
000 or 001?are there any differences?Thanks!

hi
Do client copy with client 000 and user sap* only .
001 is the copy of 000 .
rgds,
Arun

Boot Camp - "No AMD graphics driver is installed" error during win8.1 post-install

Similar Messages

Maybe you are looking for