Bootcamp says there is no USB-CD Device installed

Hello,
i dont understand, Bootcamp says that i have to plug in a USB CD-Device to continue (I must install Windows 7 nativly).
But i have one connected. I do this not the first time. I did this bevor with the Same Mac and Same USB-CD-Dive?
Is this a Mavericks Bug?
kind regards

I have the solution.
For people with the same issue as me i want to tell the reason.
You have to connect an externel DVD-Device plus a USB-Stick.
This is the first time that Apple poped up a window with unclear instructions Apple is human, here is the first prove.

Similar Messages

  • Boot Camp Assistant says There is no USB drive connected to the system

    I have a mid-2012 11” Macbook Air and a USB Superdrive. I am trying to use Boot Camp Assistant but it is not letting me proceed. With the Superdrive plugged and Windows 7 (full version) DVD in the drive, I get the message “No USB Drive” – “There is no USB drive connected to the system. Please insert a USB drive to continue.”
    I checked using Finder and Go->Computer and there is the Windows 7 installation DVD mounted properly. The Superdrive spins up when I plug it in. I tried both USB ports. I tried re-booting with the Superdrive attached. The laptop is plugged in and there is an internet connection. It is running Mac OS X 10.8.3. I read the Installation and Setup PDF guide and there was no mention of the problem. I searched these forums and found that two other people are/have experienced the same problem, but there is no posted solution.

    Randall Venhola wrote:
    At the second step in the wizard, there is a dialog with three check-boxes. The only way I can proceed is if I uncheck the option "Download the latest Windows support software from Apple". When checked, I get the "No USB drive" message. Checking or unchecking the other two options does not change the behavior ("Create a Windows 7 or later install disk" and "Install Windows 7 or later"). I have tried with the Superdrive attached with Window 7 in the drive, with a blank DVD and without the Superdrive.
    You are not following the Boot Camp instructions. Did you select the option to read the instructions? When running Boot Camp Assistant you are given the option to download the support software. If this is selected you must connect a usb stick that is correctly formatted per the instructions. At this point in the process you sshould not have your superdrive or Windows dvd connected.
    Read the instructions.

  • Mac says there is no default application to install shockwave 11

    i have been trying to install the new version of the shockwave 11 player for my imac. i have installed it onto my desktop, but now that i double click on it it opens a window telling me that theres no default application specified to open the document. its a pkg file. how am i supposed to install this onto my imac?

    Is this an Intel or PPC iMac? If an Intel Mac go here for the Intel version.
    Select the .pkg file and press COMMAND-I to open the Get Info window. In the Open With section select Installer from the drop down menu then click on the Change All button.

  • BootCamp Says Only 16GB Free ! Going to Install Windows8 !!!! Helppp

    Hello,
    I'm going to install Windows8 via Bootcamp but with more than 64GB of free space
    while partitioning Bootcamp shows only 19GB free for MAC and I'm not able to partition
    and continue with the installation .
    Here is the error pictures:
    Also my finder show 64GB of free space but disk utility shows only 38GB of free space.
    Here is the photo:
    Would you please help me in this regard?
    I also tried to follow the below thread but I did not understand how :
    https://discussions.apple.com/thread/3296146?start=0&tstart=0
    Please Help !

    You do not have sufficient free space for a Windows 8 (or 7) installation.

  • How to detect if there is a USB Storage in my pc? VISUAL BASIC 6.0

    Hi sir. 
    my program has a function auto back up.  so i want to detect if there is a usb or not. if there's a usb then it will be save in the available usb storage. if there is no usb it wont save and will pop up a msg box saying "There is no USB device,
    please insert USB to continue back up" VB6 platform
    thank you sir.

    Hi NikkoProgrammer,
    Welcome to MSDN.
    I am afraid that as Renee Culver said, these forums donot support VB6, you could refer to this thread:
    Where to post your VB 6 questions
    You could consider posting this issue in these forums below:
    These forums do not support Visual Basic 6, however there are many third-party support sites that do. If you have a VB6-related question please visit these popular forums:
    VB Forums
    VB City
    Thanks for your understanding.
    Best Regards,
    Youjun Tang
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

  • There is no USB drive connected to the system.

    I have plugged in the Superdrive to the new iMac 27 that came yesterday.
    This comment is being given when I am in bootcamp.
    "There is no USB drive connected to the system."
    The Superdrive is plugged into a USB Drive and when you place a cd/dvd in the Superdrive the mac picks up that there is a disk in the Superdrive.
    How can correct this issue?

    Note: I would like to download the latest Windows support software from Apple onto a DVD so then I can install Windows 7 using bootcamp.
    I prefer not to us a flash drive.
    What is the easiest way to correct this issue?

  • HT3986 Why my Boot Camp keep saying that there is no USB device connected ?

    I use Mac Air, and with a external CD device. When I try to install Window 7, it keep saying that there is no USB device connected when there is.

    Unfortunately not all external CD drives work the same, have you tried another cable or used another slot?
    Have you tried using a USB flash drive? You should have an option now in Boot Camp Assistant to install the W7 installer onto a USB drive as well as the Boot Camp drivers.

  • My lap top wont import pictures from auto play. it keeps saying there is a file error and a device connected to the computer isnt working properly. i have tried going into the internal storage to copy and paste the pictures but this wont work either.

    my pictures from my i phone 4s wont import from auto play. a message keeps coming up saying there is an error and a device is not working properly. also i have tried going into the internal storage to copy and paste them but that wont work either. the page either stops responding or the picture simply dont copy. does any1 have any idea why this is happening. it has never happened before and only seems to be happening since i started using i cloud storage instead of synching my phone with the lap top.

    I have decided to dedicate this thread to the wonderful errors of Lion OSX. Each time I find a huge problem with Lion I will make note of it here.
    Today I discovered a new treasure of doggie poop in Lion. No Save As......
    I repeat. No Save As. In text editor I couldn't save the file with a new extension. I finally accomplished this oh so majorly difficult task (because we all know how difficult it should be to save a file with a new extension) by pressing duplicate and then saving a copy of the file with a new extension. Yet then I had to delete the first copy and send it to trash. And of course then I have to secure empty trash because if I have to do this the rest of my mac's life I will be taking up a quarter of percentage of space with duplicate files. So this is the real reason they got rid of Save As: so that it would garble up some extra GB on the ole hard disk.
    So about 20 minutes of my time were wasted while doing my homework and studying for an exam because I had to look up "how to save a file with a new extension in  mac Lion" and then wasted time sitting here and ranting on this forum until someone over at Apple wakes up from their OSX-coma.
    are you freaking kidding me Apple? I mean REALLY?!!!! who the heck designed this?!!! I want to know. I want his or her name and I want to sit down with them and have a long chat. and then I'd probably splash cold water on their face to wake them up.
    I am starting to believe that Apple is Satan.

  • My apple ipod classic 80gb says there is no music - anything on my ipod, but says it only has 37gb free. Then i try and plug it into my pc with iTunes on (i've set it to do not automatically sync devices) but it still freezes every time. can't restore.

    my apple ipod classic 80gb says there is no music - anything on my ipod, but says it only has 37gb free. Then i try and plug it into my pc with iTunes on (i've set it to do not automatically sync devices) but it still freezes every time. the only way to unfreeze it is by detatching the ipod or resetting with menu/centre (until it loads up again, where it immediately unfreezes and comes up with a load of messages saying "cannot read iPod" and when i try and restore it by pressing menu/centre button while it's plugged in, it says "cannot restore as it is being used by another program" or "error 1415". Any ideas how to sort this out? hope i haven't majorly screwed it up. thanks.

    Sorted it out. If anyone has this problem i reccommend visiting http://forums.ilounge.com/ipod-classic-ipod-5g-video/237546-ipod-classic-80gb-fr eezes-itunes-need-restore-plz-help-2.html#post1403546 there's some pretty good advice on it. have to go into control panel and re-format iPod into NTFS file. good luck.

  • Cant Charge/connect ipod touch. Get an error saying "One of the USB devices attached to your computer has malfunctioned, and Windows does not recognize it" . HELP.

    Ok . so my ipod touch 2G , used to be all ok . its just yesterday i went to charge my ipod it wouldnt do anything . Then after being plugged in for a bit , i got  pop up saying "  "One of the USB devices attached to your computer has malfunctioned, and Windows does not recognize it" .
    Ive tried plugging this into 3 other computers same error message pops up .
    PLEASE help me . thanks (:

    Uninstall your USB drivers in your computer & reinstall.
    contact your pc manufacturer for the steps.
    Although I am working on behalf of HP, I am speaking for myself and not for HP.
    Love Kudos! If you feel my post has helped you please click the White Kudos! Star just below my name : )
    If you feel my answer has fixed your problem please click 'Mark As Solution' and make it easier for others to find help quickly : )
    Happy Troubleshooting : )

  • HT1476 when i plug my phone into the usb port with the apple charger that came with my phone i get an error msg say charging not supported by this device.   But when i use a gigaware (radioshack brand) usb charger, no error msg.  Why?

    when i plug my phone into the usb port with the apple charger that came with my phone i get an error msg say charging not supported by this device.   But when i use a gigaware (radioshack brand) usb charger, no error msg.  Why?

    - Try restoring the iPod, first from backup and then try to factory settings/new iPod to rule out a software problem.
    - Look at the dock connector on the iPod. Look for abnormalities like bent or corroded contacts, foreign material and broken or cracked plastic.
    - Could you have damaged something when you took the iPod apart and replaced the Home button?

  • I have a ipod nano 1st and 2nd generation and am trying to put music on it but every time windows says one of the usb devices attached to this computer has malufunctioned and windows does not recognize it code 43 can someone help me please

    i have a ipod nano 1st and 2nd generation and am trying to put music on it but every time windows says one of the usb devices attached to this computer has malufunctioned and windows does not recognize it code 43 can someone help me please

    Try putting it into "Disk Mode" http://docs.info.apple.com/article.html?artnum=93651
    Then with it in this mode connect it to the PC and try to run the latest iPod updater to do a restore and update software if you have the option. the latest iPod updater is 2006-03-23 and can be downloaded here http://www.apple.com/ipod/download/

  • Computer says 'one of the USB devices attached to this computer has malfunctioned and windows does not recognize it'. what do i do?

    i have an ipod nano 7th gen and when i plug it in for itunes my computer says 'one of the USB devices attached to this computer has malfunctioned and windows does not recognize it'. what do i do?

    As I said above, some of the new lightning cables have been known to be causing problems for some users.  Have it replaced if at all possible by bringing it into your local Apple Store's Genius Bar.
    B-rock

  • HT3986 This what my boot camp says , when ever i am trying to instal windows 7 ''There is no USB drive connected to the system. Please insert a USB drive to continue.    "' Can someone help me . ?

    This what my boot camp says , when ever i am trying to instal windows 7 ''There is no USB drive connected to the system. Please insert a USB drive to continue.

    pump

  • My A'Extreme sometimes won't connect to my MacBook Pro even if I have a green light on the device . I can unplug the ethernet cable and reconnect and it will work fine. all diagnostics say there is nothing wrong. Any ideas ?

    My A'Extreme sometimes won't connect to my MacBook Pro even if I have a green light on the device . I can unplug the ethernet cable and reconnect and it will work fine. all diagnostics say there is nothing wrong. Any ideas ?

    This is more about your modem then anything. Sometimes you'll need to unplug and plug back in your modem. Consider it a glitch from the ISP or just the modem in general.
    when I need to turn something off then on I try the modem first. This when I'm not doing any ware and tare to the device.

Maybe you are looking for

  • HowTo read file from app. server and store it in binary format (SDOKCNTBIN)

    Hi I need to upload Documents to Document Repository by using to function module RSOD_DOC_MAST_CHANGE. My question is: How can I fill the "parameter" i_t_file_content_binary from a file which is stored on an application server. br, michael

  • Iphone 5c clock not working

    ive tried restoring it, and resetting it completly. its been like this for a couple days now. i have even tried setting the time manully.. it works until i lock my screen, when i go to unlock it its still at the same time as when i locked it. please

  • External task and Multiple-join

    In a process, the order of activities is: Begin->interactive activity A -> multiple -> interactive activity B -> Join -> interactive activity C This process has 2 instance variable, var1 and var2. var1's type is BPMObject var2's type is String. PBL c

  • ECR/ECO Workflow not working for multiple Objects

    Hello all, We have implemented ECR/ECO workflow by customizing the SAP standard one. We are facing a problem when entering multiple ECO objects such as mutiple Documents, materials, BOMs etc. When we create the ECR, two parralel workflow start (one f

  • Why this warning is rised when creating database in RAC?

    Oracle 11.2.0.3 RAC in RHEL 5.8 Whether in runinstall or in dbca,there is always a warning :  Entreprise manager configuration succeded with  the following warning Error starting Database Control on nodes rac2. Execute the following command(s) on nod


HashFlare