Bridge Offset Nulling Doesn't Seem to Work With SCC-SG24

Does anyone know if the DAQmx "Perform Bridge Offset Nulling Calibration" vi works with the SCC-SG24 modules?  We have used our NI-9237 module in the past to acquire dual-channel load cell (thrust & torque) measurements, and calling that vi does a fine job of zeroing out the values before applying the load.  However, it doesn't seem to work when we try to take the same measurements using an SCC-SG24 module.
We are able to zero the values manually, by using the nulling resistors and potentiometers in the SCC-SG24.  But, whether the nulling resistors are installed or not, we are not able to zero the values using the "Perform Bridge Offset Nulling Calibration" vi.  Running that vi does induce a significant offset in the values, but it is not the correct offset needed to bring the values to zero.  For example, with no load applied, a torque reading before running the vi may be +1090 in-lbs, and be "zeroed" to -465 in-lbs after running the vi.  Running the vi multiple times (to check repeatability) always brings us back to approximately -465 in-lbs.
An additional issue (not sure if it's related or not) is that if we try to run this vi to offset just one of the channels in the task (such as just thrust, but not torque) it will still induce a small offset in the other channel, which doesn't seem right.
I guess I'm not clear on whether the subject vi is performing an operation on the hardware, the software, or both, so I'm not sure whether the SCC-SG24 modules may not be compatible with this vi?
Thanks for any help you can provide.

Hello Dhruser1,
I think that the DAQmx Perform Bridge Offset Nulling Calibration should work for the SCC-SG24 module.  Take a look at this article:  Removing Large Initial Offset for Load Cell or Strain Measurements with SCXI-1520 or PXI-4220 in particular it mentions that using this VI in addition to the auto zero can introduce an offset.  If you're doing both these is likely the cause.
Also, when you specify specific channels using the channels input are you also setting the "skip unsupported channels to false?  If not this may be why it affects other channels.
I hope this helps, and if not please feel free to post back with an update after trying these things.
Cheers,
Brooks

Similar Messages

  • Email Security Plug-in - Doesn't seem to work with right click or save and send

    I've searched the knowledge base but have not located the answer yet.
    We have the Encrypt Message plug-in installed to flag the email [SEND SECURE].  This works very well when in Outlook.  It does not seem to work when right clicking a file to send outside of Outlook or performing Save and Send from within Microsoft Office.  The add-in still shows and users are clicking it and the Send button but the emails are not going securely.  We are on Microsoft2010 on mostly XP machines.
    How can I get Encrypt Message to work in all instances?
    Thank you.
    Starla

    Andreas
    I am getting an error.  See below for what I'm choosing and the response.  let me know if I'm supposed to be trying to download from another area.
    Thanks
    Starla
    Email Security Plug-in - Doesn't seem to work with right click or save and send
    Cisco IronPort Email Security Appliance C370
    Release:IPAS
    Filename: CiscoEmailSecurity_7-2-0-039.exe
      Remove
    Details
    Release
    IPAS
    Filename
    CiscoEmailSecurity_7-2-0-039.exe
    Release Date
    25/Oct/2011
    Description
    Cisco IronPort Email Security Plug-in (Outlook)
    Size
    32541.84375 KB (33322848 bytes)
    Router Checksum
    0x553f
    MD5
    f0c864697d9e1a3e8f5297062943ac50
    Email Security Plug-in - Doesn't seem to work with right click or save and send
    Save the device to 'My Added Devices' list
    More Info
    'My Added Devices' list could be found by: 1. Clicking on 'My Cisco' Tab and expanding
        the 'Added Devices' section. 2. Selecting any task specific product
       selector and clicking on 'My Added
        Devices' in left pane.
    Email Security Plug-in - Doesn't seem to work with right click or save and send
    Set Cisco Notification Alert
    More Info
    All 'Cisco Notification Alerts' list could be found
    by: 1. Clicking on 'My Cisco' Tab and expanding
        the 'Support Notifications' section.
    Cisco service contract information indicates you are not authorized to download software for the following product(s):
    Cisco IronPort Email Security Appliance C170
    Cisco IronPort Email Security Appliance C370
    Cisco IronPort Email Security Appliance C650
    To download software for other product(s), remove the software for the product(s) listed above.
    Or, if you feel this message is in error, please:
    1. Email technical support for 24x7 assistance. To expedite your request, please include the following information:
             User ID (Cisco.com ID used to download software)
             Contact Name
             Company Name
             Contract Number
             Product ID
             Desired Software Release or File Name
    2. Contact your Cisco Representative, Partner or Reseller to ensure product(s) listed above are covered on a service contract. The Partner Locator link may assist in locating your nearest partner.
    3. Associate contracts for those products to your Cisco.com profile using the Instructions found in Profile Manager. After you submit your additional contracts, verification and updates may take up to 6 hours to complete.

  • Siri doesn't seem to work with Find My Friends

    Siri doesn't seem to work with Find My Friends completely accurately. If I ask it where once of my friends is, it tells me it doesn't know, but shows that person in the response, twice, with their location. Anyone experiencing this?
    Also - I found a bug. If you dictate a note via Siri it will not sync with iCloud at all. If you manually update the note however after Siri dictates it will. It will also sync if you manually start a note and then use the microphone on the keyboard.

    Actually, I figured it out. For the person in question I had both [email protected] and [email protected] listed in their contact info.  When you look at them in Find My Friends see which one is highlighted and delete the other. Once I did that they only showed up once in Siri.

  • 2013 Workflows created in SharePoint Designer doesn't seems to work with retension policy!

    Hi Guys, 2013 Workflows created in SharePoint Designer doesn't seems to work with retension policy but 2010 workflows work. Any One have any details resaon or workarround?
    Shafqat Balouch MCT, MCSA, MCSE MCITP, MCPD, Microsoft Partner

    Hi  ,
    According to your description, I can reproduce your scenario in my SharePoint 2013.
    For the Retention Policy, it will schedule how content is managed and disposed by specifying a sequence of retention stages. In SharePoint Designer Workflow 2013, we have looping option available. You can
    use loop option and then pause for duration for achieving same function as Retention Policy to start a workflow.
    Reference:
    http://prasadtechtactics.blogspot.com/2012/07/sharepoint-designer-2013-workflows-part_24.html
    Thanks,
    Eric
    Forum Support
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support,
    contact [email protected]
    Eric Tao
    TechNet Community Support

  • I would like to cancel my subscription for Adobe ExportPDF Subscription that I have just signed up for as it doesn't seem to work with my system. How do I do this ?many thanks suslucie

    I would like to cancel my subscription for Adobe ExportPDF Subscription that I have just signed up for as it doesn't seem to work with my system. How do I do this ?many thanks suslucie

    Hi Susan,
    I checked using the email you provided, and there's no history of any orders under that email address. (Then, I removed your email address from you post, since this is a public forum and it's best not to broadcast contact information.)
    I'll message you privately, and you can send along your email from Adobe if you'd like.
    Best,
    Sara

  • Is there a way of using IE7 with Mountain Lion? There used to be this facility using Safari "Develop" with Lion, but this doesn't seem to work with ML

    Is there a way of using IE7 with Mountain Lion? There used to be this facility using Safari "Develop" with Lion, but this doesn't seem to work with ML

    Thank you for this, and to Caleb.
    I've tried using Caleb's approach (which is the same as I used with Lion), but the programme doesn't respond now that I have installed Mountain Lion.
    My problem is that I do not want to use IE7 but that a programme I need regular access to will only allow IE7 and I've been told by the developers that it is too expensive to upgrade this programme to allow it to be used by other browsers.
    So, my puzzle remains the same. I could access IE7 and use the programme using Caleb's solution with Lion. I can't do the same with Mountain Lion. I do (I think!) understand your point about the programme requiring IE7 specifically, but if it worked on Lion, why isn't it working on Mountain Lion? Or was I just lucky before?
    I'll try mende1's approach, though I doubt I'm technical enough to virtualise anything!
    Thanks again. Any further thoughts welcome.

  • Can someone tell me why a standard microphone doesn't seem to work with a mac-mini? Is there another kind of microphone I need to use?

    can someone tell me why a standard microphone doesn't seem to work with a mac-mini? Is there another kind of microphone I need to use?

    Most microphone output a low voltage signal that must be put through a preamp.
    The computer needs to have a line voltage signal level instead.
    Allan

  • My New HP P2015d Printer ($400) doesn't seem to work with New Pavilion Slimeline 64 bit PC !

    My New HP P2015d Printer ($400) doesn't seem to work with New Pavilion Slimeline 64 bit PC ! I need some suggestions. Any help would be appreciated.
    The printer worked for a while and then out of the blue stopped working. We have a virus protection system, so I doubt it is a virus issue.
    *** We already tried to download the latest drivers and that doesn't seem to work ***

    Hi
    Are you trying to find your printer's email address? If so, check out details below
    http://h30434.www3.hp.com/t5/ePrint-Print-Apps-Mobile/how-do-I-find-my-printer-s-email-address/td-p/...
    Although I am an HP employee, I am speaking for myself and not for HP.
    Twitter: @Ciara_B_HP

  • Annotations - InheritanceType.TABLE_PER_CLASS doesn't seem to work with GF

    Hi there,
    I'm using the toplink essentials jar file with a stand alone J2SE application. I'm using annotations for ORM with Toplink implementation
    What I want to achieve is to map the base class objects to one table, and sub class objects to a different table. Currently - both tables (and objects) have the exact same structure, but I use inheritence in order to identify where should the object be registered. Thus I'm trying to map an inhertiance using TABLE_PER_CLASS type.
    It doesn't seem to work:
    My classes look like this:
    Base class I want to map to REGION table:
    @Entity
    @Table(name="REGION")
    @Inheritance(strategy=InheritanceType.TABLE_PER_CLASS)
    public class Region implements BaseBusinessObj
    @Id
    @Column(name = "REGION_ID", insertable = false, updatable = true)
    @GeneratedValue(generator = "regionSeq")
    @SequenceGenerator(name = "regionSeq",
    sequenceName = "GSM_REGION_ID_SEQ", allocationSize = 1)
    private int m_regionId;
    @Column(name = "REGION_NAME")
    private String m_regionName;
    Subclass with exact same structure I want to map to GFR_REGION table which has the exact same database table structure as REGION:
    @Entity
    @Table(name="GFR_REGION")
    public class GfrRegion extends Region
    This doesn't work. The Toplink adds entities of the GfrRegion to the REGION table and does not recognize it should go to the GFR_REGION table.
    What am I doing wrong?
    Thanks,
    Michael

    Hi all,
    Any news about the support for TABLE_PER_CLASS in TopLink/EclipseLink ?
    The main question is what was the reason for making this an optional strategy for mapping in the specs ? Both OpenJPA and Hibernate have it and there are cases when this is usefull.
    From EclipseLink perspective, how difficult would be to add this ? I didn't have a chance yet to closely examine the codebase for EclipseLink, but some architecture diagrams with some design decisions explained would help to community to better understand the product and make improvements.
    Thank you,
    Mircea

  • @protocol doesn't seem to work with non-primitive arguments

    Any idea why this works.
    CustomProtocol1.h
    @protocol CustomProtocol1
    - (void) start:(int) offset;
    @end
    But this doesn't:
    CustomProtocol2.h
    @protocol CustomProtocol2
    - (void) start:(CustomClass*) custom;
    @end
    The only difference is that CustomProtocol1 uses a non-primitve argument. Here is the error I get for CustomProtocol2: "Syntax error before 'CustomClass'. Method definition not in @implementation context"
    It seems CustomProtocol2 has problems finding the CustomClass.h but if I add #import "CustomClass.h" into CustomProtocol2.h I get this error: "Cannot find protocol declaration for 'CustomProtocol2'"
    So far, I can only conclude that Objective-C @protocol does not work with non-primitives.
    Any help would be MUCH appreciated.
    Anthony

    The compiler doesn't know what CustomClass is. You have to tell it. However, it is a pointer and, hence, actually is a "primitive" (AKA POD - plain 'ole data) type. So, you need to forward declare CustomClass like so:
    @class CustomClass;
    @protocol CustomProtocol2
    - (void) start:(CustomClass*) custom;
    @end

  • Flash Builder 4 profiler doesn't seem to work with Flash Player 10.0

    Hi,
    I've been trying to get the profiler to work with Flash Builder 4, but when trying to profile on Flash Player 10.1, 11 or 11.1, Flash Builder doesn't connect to the profiled SWF.
    Changing my Flash Player to an old, debug version of 10.0.45 works fine.
    Is this a known bug, or is it just an incompatibility that's fixed in Flash Builder 4.5?
    thanks
    Richard

    I’m profiling just fine in 4.5

  • 1Password doesn't seem to work with Firefox 5 - I was told it would recognize and get the new 1Password addon but not working ... ???

    I've been keeping my passwords in an application called 1Password. I was assured (by a knowledgeable user, not by anyone official) that when I upgraded to Firefox 5.0, the 1Password addon would be updated ... But that doesn't seem to have happened. As I rely on 1Password to track my passwords, this is a problem.

    Take it back to the place that installed the battery and ask them to check their installation.

  • My new TomTom doesn't seem to work with my MacBook Pro (OS version 10.7.2). Is there any way I can make it work?

    The message that comes up when I click on "TomTom Home Install" is "You cannot open Home Install because Power PC applications are no longer supported." Does this mean that the TomTom, which is absolutely vital to my life - well, not literally but you know what I mean - can no longer be used with my MacBook Pro? Does Apple want to drive us into using PCs or what is going on? Is there a driver or some other clever means of making the TomTom work as they used to work with Macs? This is an urgent question - please help if you can! Thanks. Bill

    coxorangepippin wrote:
    The message that comes up when I click on "TomTom Home Install" is "You cannot open Home Install because Power PC applications are no longer supported." Does this mean that the TomTom, which is absolutely vital to my life - well, not literally but you know what I mean - can no longer be used with my MacBook Pro?
    What that means is that is can't be used with Lion 10.7.  PowerPC was the chip Apple used up until 2006 when they switched to Intel.  At that point, they created the Rosetta emulator to allow for PPC support for 5 years.  They finally dropped the support with the release of Lion.  It will only work with OS X 10.6 or earlier.  The other option is to purchase a new GPS, which can be had for $100 for a decent one.

  • My iPad doesn't seem to work with the hdmi connector

    I have a first gen iPad and I can't get it to display with the hdmi adapter.  My iPad 2seems to work fine.  I thought it worked for both gens.

    It should work for both generations.  It won't mirror with the iPad1, but it should play videos.  My iPad1 DID play videos - for a week or two.  Then it quit working with the HDMI adapter.  Still behaves as before with the Component adapter.  Nothing wrong with the cables, tv, etc.  Aftyer ruling out all else, I exchanged the Apple HDMI adaprter for a new one - same thing.  My iPad1 now has no idea there is an external tv/display connected when using the HDMI adapter.  I suspect my mistake was in updating the iPad to the newest iOS software release.  I'll bet this is what broke it.  The question is:  Will this bug be fixed, or is this new non-compliance going to be considered by Apple to be a  'feature'?
    Apple?

  • Delete button in main Mail window doesn't seem to work with update to 10.5.

    Hi, I just upgraded to OSX 10.5.8 and now the delete button in the main mail window does not seem to be working. The other buttons work, and if you hit the delete key that works. The delete button at the top of a message window also seems to continue to work. This is strange behavior. I will try to reboot again to see if that helps.

    I am seeing the same issue. Very annoying. Tried resetting the toolbar too - did not work. Any help Apple?

Maybe you are looking for

  • Connect BPCS with R/3

    Hi, does anybody have experience connecting BPCS (automotive supply industry) software with R/3 over XI? A documentation or a link would be very helpful, Regards, Udo

  • SAP Content Server error 405    Method Not Allowed

    Hello Everyone We have installed SAP Content server 04s with SAP DB 7.6 build on Solaris platform.  We are trying to connect it through ECC. We have configured Apache web server on content server, and we are able to access it through http url. On ECC

  • Problem viewing Numbers spreadsheet via VNC

    When I connect to an Intel Mac Mini running 10.5.6 using a VNC client and launch Numbers (2.0.2) on the Mini, a valid spreadsheet opens but it looks blank (no cells visible, no data visible). The program is fully functional and if the arrow keys are

  • Trace a BIP Report

    Hello, Is there a way to Trace a BIP report so that I can see the BIP session on the database server along with the SQL that's running? What I am looking for is a way to identify a BIP session so that our DBA can identify a given user's BIP session/r

  • HT201303 Do I have to put a cc in to download free apps?

    Do I have to put a cc on file to download free apps???