Bronze keyboard Will not start from hard drive

This computer (333 Mhz Lombard 192MB ram) has a 40GB seagate HD recently installed, It has Mac OS 10 on it and 9.2.1. I've run multiple tests on it using Apples Mac Test pro and all the tests have passed. It starts readily from the CD I have also recently replaced the battery and pram battery. All i get from the computer at start up is the flashing ? mark blinking system folder. I've reset the pram and power manager, not sure whats wrong. any help would be appreciated. Thanks, Mark

The blinking ? means the Mac can't find a valid startup system.
Look at A flashing question mark appears when you start your Mac
http://docs.info.apple.com/article.html?artnum=58042
Are you trying to start up in OS 10 or OS 9? If OS 10, depress the Option key at startup which opens to the Startup Manager window. Then select the OS 9 icon & click the right arrow. If OS 9, do the same but select OS 10.
 Cheers, Tom

Similar Messages

  • Power Mac G4 400 MHz (AGP graphics) will not boot from hard drive

    I have a Mac G4 400 MHz (AGP graphics) Machine Model: PowerMac 3.1 CPU Type:PowerPC G4 (2.8)
    When I try to boot from the hard drive I get the folder with the flashing question Mark. The Machine will start up from the OSX 10.4 installer disk.
    The system was running OSX 10.4.9 fine. I began to have problems with the hard drive, so I replaced it with an old Maxtor 5T040H4 40Gig Apple branded drive that I had sitting around.
    The drive is jumpered (r50) for Master/Single.
    I erased the drive in the old G4 using disk utility and wrote all zeros. I then used my store bought Tiger 10.4 install disk to install 10.4 on the drive.
    After restarting I still get the flashing question mark. If I leave the Install disk in the DVD drive the system will attempt to install again.
    I have zapped the PRAM, pressed the CUDA button, removed the battery and let the system sit unplugged for over and hour and it still will not boot from the hard drive.
    To test the drive I removed it and put it in a Granite Digital firewire enclosure and connected it to another mac. The drive shows up and the system appears to be installed correctly.
    What am I forgetting to do? Does anyone have any suggestions.
    Thanks in advance.
    Wesley G.

    Hi! If Tom's solution doesn't work I would reboot from the install disc and then partition the drive as 1 partition instead of erasing it. Sounds like the driver on the disk is too old and installing a new partition map should write a new driver to the drive that is compatible with Tiger. Other than that it is possible that the drive has a spin delay jumper enabled and the drive isn't spinning up fast enough and the computer isn't looking long enough for the drive. Tom

  • After 10.5 upgrade Mac will not boot from hard drive

    I just upgraded to 10.5 Leopard but my mac will not boot from the hard drive even after selecting my hard drive as the startup disk. The mac will start to boot but will cut itself off before the boot is complete. I have to leave the Leopard disk in the mac and hold down C to get the mac to turn on but it only allows me to install the software again.

    instead of archive and install you might first want to try restoring your system using TM to some time point before your failed 10.5.1 upgrade. Then try upgrading to 10.5.1 again. I would suggest downloading the full 110 MB upgrade and installing it manually rather than doing it through the software upgrade menu.
    You can download the upgrade here:
    http://www.apple.com/downloads/macosx/apple/macosx_updates/macosx1051update.html

  • EMac Will Not Start From Firewire Drive

    I'd like to revive my old eMac to use as secondary machine for surfing, etc.
    The internal hard drive failed so I bought a Western Digital My Passport drive. I used my old retail copy of Leopard (the same copy I had used on the internal drive) and installed Leopard. The Startup Disk application showed that 10.5 was installed on it and allowed me to choose it for the startup drive.
    However, after startup the eMac refuses to see the FW drive. It doesn't even appear to poll it as the drive's light never blinks after the initial power on. Holding down the option key only shows the old internal drive and Leopard install disc as options.
    What am I doing wrong?? I never had a problem booting any Mac from a FW drive before.
    Additional notes...
    1. I reformatted the drive and made sure it was set to Apple Partition Map.
    2. I tried dividing it up into multiple partitions.
    3. I disabled the stupid Smartware software with the Virtual CD Manager.
    4. Looking at the drive on my current Snow Leopard Mac, it appears to have a valid installation.

    A few ideas.
    Did you use the Disk Utility app on the 10.5 Leopard DVD to format the drive as an Apple HFS+ drive?
    Try another FW port. The eMac has 2.
    My Mom's eMac is a 800 MHz model running Leopard 10.5.8 from an ext. FW drive.
    It usually takes this eMac a good minute and a half to two minutes to see the FW drive and then it will boot to it.
    Could try and startup the eMac and wait a little while for it to boot?
    Do you get the flashing question mark folder icon when you first start the eMac?
    If you do, you may need to wait a little while for the eMac to see the drive.

  • Mac will not boot from hard drive or install disc

    Hello All
    In dire need of advise...my intel Mac will not boot, even tried booting to the Snow Leopard install disc and all I'm getting is the white screen, apple logo and the wheel.
    Just before this happened there was a buzzing sound like the fan was about to fail but that is only a guess on my part. Is there a keyboard shortcut to boot to a terminal window or similar to force the computer to boot from the install disc.
    Thanks in advance for any help offered.
    Warren

    Hi Warren
    Try holding the Option key and see if it will boot into Startup Manager, where you should be able to choose from a good Drive or your install Disk.
    http://support.apple.com/kb/HT1533
    or the D key and run the Apple Hardware Test.
    http://support.apple.com/kb/HT1509
    Also note: key commands may require a USB Keyboard if your using a wireless and it has become unpaired.
    Dennis

  • Lightroom 5:  "Remove Photo" will not delete from hard drive

    I just discovered that when I am using the "Remove photo" feature from the library, while the photo is removed from the catalog and "deleted", it remains on my external hard drive.  Is there a fix to this issue?  I did go to my external drive and create a file and then delete it.  I had read in other forums that this allowed Lightroom to find the correct place. This did not solve my problem.
    Thank you for any assistance.
    Karen

    Yes I do.
    After I posted, I tried it again in a different file (I organize my photos
    on my external drive by month and year).  In the month of August file, I
    can delete in Lightroom and it deletes from my hard drive.  It appears to
    only be happening in my September file, at least as far as I can tell now.
    I created all of my file folders 2 months ago, so it isn't something I
    just did.
    Any thoughts?

  • Mac OS 10.5 /  I deleted the " Private" folder ... and emptied the trash. So the folder and its contents no longer exists on my computer at all !!!  I do have the OS dvd that i purchased years ago...  But my computer will not start from it on its own. My

    Mac OS 10.5 /
    I deleted the " Private" folder ... and emptied the trash. So the folder and its contents no longer exists on my computer at all !!!
    I do have the OS 10.5 dvd that i purchased years ago...
    But my computer will not start from it on its own.
    My question is what is the open source or terminal language code used to tell my mac to look in the DVD rom drive for startup info?  I know that im not the only person in this world who has deleted the "PRIVATE" folder and emptied the trash so it no longer exists on their machine...
    That said theres gotta be a common fix for a Power PC G4 that has the OS X dvd in the rom drive but wont look to it to reinstall the vital contents of the PRIVATE folder.
    Once again there is not a copy of this file or its contents in the recycle bin...
    Also rebooting the machine , pressing and holding the letter C does not prompt the machine to look to the dvd rom drive.
    I was reinstalling pro tools and figured I would make some room by cleaning my computers HD...
    Lol It was a bad choice to delete this file ...
    Thanks guys

    Okay sorry it took forever to respond... But for a while there I gave up on this computer!!!!
    Money's been tight lately , so taking it in to a professional was not yet an option... though I did consider it eventhough.
    Anyway long story short im glad I didnt spend any money because I already had all the tools necessary to fix this issue but was going about it in the wrong way. Okay so here is my scenario and the breakdown... Though this may not fix the issue for everyone :( which *****... But I know we all will have different circumstances.
    Anyway here we go...
    Okay so first things first....  Years ago I purchased the OS 10.5.1 disk ... So that has always been in my possession!!!!
    I realize that some may not have a disk to reflash your OS to your hard drive... but if you do your in luck.
    2ndly ... I had an external harddrive with all of my itunes downloaded music so it was more than okay with me to delete my primary HD because all the important stuff could either be copied over or repathed to be located.
    -------If you dont want to read through the whole story the fix is summed up in the bottom section-------
    Okay so now the SOLUTION!!!!
    By trial and error , and pure boredom I opened up my computer to clean the inside...
    AND
    "Disconnected the primary HD"
    and just because ....... REBOOTED my computer. Just to see what it would do.
    Upon restart and though it looked like it would repeat its usual cycle...
    About 1 minute in to that process my computer froze for about 2 seconds and flashed to the OS installation screen.
    Mind you I havent seen this screen yet... Probably hasnt been since I installed the OS years ago.
    After a bit of trial and error...
    I decided to tell my computer to startup from the OS 10.5 disk located in my dvd rom drive and restarted once again...
    this setting is under
    Utilities / startup disk
    After a little more trial and error ... I realized that I could reconnect the primary HD , restart the machine and return to the OS installation menu.
    So upon this discovery
    I went to the Disk Utility located under Utilities
    Highlighted my primary HD located in the left hand column
    Once highlighted ...
    In the heading section on the right I selected the option
    Erase
    in which I erased My current OS on my primary HD ...
    I used the first option in the list under security... Because it seemed like the least invasive and would take the least amount of time to see if this process would actually work.
    I FORGOT to add something... 
    Another reason why I deleted my primary HD!!!!!
    I forgot to say that it WOULD NOT!!!!! Show up in the STARTUP list as an option...Even After multiple reboots....
    But like clockwork... Once I deleted its name IT SHOWED UP as an option!!!!
    So back to the next step...
    I returned to the STARTUP option under utilities ... And was then able to see MY primary HD now as a startup option...
    But ofcourse it had no name because it we previously erased it.
    So when Clicking my newly erased HD ... I was almost immediately prompted to REINSTALL the OS ...
    Which said it would take about 57 minutes ... But I believe was alot less...
    My issue was resolved ... My computer then stated the install was SUCCESSFUL!!!!!!! :))))))))))) lol ;)
    It was like I was setting up for the first time ;) asking for my registration info...
    The dilemma of deleting the private folder and emptying the trash is finally over resolved. Done ... and no extra money spent!!!!!!!!! 
    Its really crazy that the information for such a simple thing is not readily available. Especially being such a simple fix.
    I know im not the only person who's had this issue , because i've seen numerous posts with similar wording.
    I also know I wont be the last person to have this issue... So I hope this synopsis makes sense.
    -------One more time the fix------
    *Insert your OS dvd into your dvd rom drive.
    *Unplug your primary HD or corrupted startup disk
    *Reboot your machine...
    Upon restart your primary HD will not be recognized...
    * you will then be prompted to select your language.
    Once selected
    *Click Utilities/startup... Highlight the the selection that refers to the OS dvd located in the dvd rom drive.
    * Click restart...
    !!!!!!!!!!Be sure to reconnect your Primary HD Before your computer restarts and you hear the chime!!!!!!!!
    If you do not replug your HD before the chime it will not be recognized.
    In that case restart again.
    Upon restart once again
    *Choose your language...
    *Click Utilities / disk utility
    In the left column select and
    *Highlight your HD ...
    Then towards the top portion / center of the page
    *Click the heading Erase
    Then on the page toward the bottom
    *Click security options
    This will then provide erase options.
    I USED THE FIRST OPTION
    "Dont erase data"...
    *click OK
    * click erase...
    Once erased which should take a few seconds
    *Cancel the disk utility...
    * Click Utilities / startup
    And your newly erased HD should now appear in the list.
    * Select your drive from the list by highlighting
    It should no longer have a name.
    *Once selected, you will then be prompted to restart and install the OS to your newly erased HD...
    Thats it!!!!
    Once everything reinstalls re-add your personal info or registration info and you are up and running.
    Goodluck ;)

  • System Profiler will not recognize installed hard drive if drive is in use by VMWare

    System Information will not recognize installed Hard Drive (Boot Camp) when in use by VMWare.
    I work in IT for a School District and I am creating a Script that system information about the computer. I am testing this on a Mac Pro with two internal hard drives. One drive is Mac OS 10.8 and the other drive is a Boot Camp Drive that is used by VMWare Fusion.
    When I run System Information via the GUI or system_profiler via Terminal, both drives show up just fine. However, if I launch VMWare Fusion and run Windows from my Boot Camp drive, then run System Information via the GUI or system_profiler via Terminal, the Boot Camp Drive is no longer listed as an installed drive.
    Example:
    In the Terminal, I enter the following command.
    system_profiler SPStorageDataType
    Then it returns this information.
    Storage:
        Lion Client:
          Available: 217.84 GB (217,836,306,432 bytes)
          Capacity: 639.28 GB (639,275,270,144 bytes)
          Mount Point: /
          File System: Journaled HFS+
          Writable: Yes
          Ignore Ownership: No
          BSD Name: disk0s2
          Volume UUID: CCB501BF-AF24-30E7-A938-5A4E52DF14D7
          Physical Drive:
              Media Name: WDC WD6400AAKS-41H2B0 Media
              Medium Type: Rotational
              Protocol: SATA
              Internal: Yes
              Partition Map Type: GPT (GUID Partition Table)
              S.M.A.R.T. Status: Verified
        BOOTCAMP:
          Available: 255.58 GB (255,575,560,192 bytes)
          Capacity: 319.79 GB (319,790,510,080 bytes)
          Mount Point: /Volumes/BOOTCAMP
          File System: NTFS
          Writable: No
          Ignore Ownership: Yes
          BSD Name: disk1s2
          Volume UUID: D4B39D4E-E244-403C-AE4D-4D58397130DE
          Physical Drive:
              Media Name: WDC WD6400AAKS-41H2B0 Media
              Medium Type: Rotational
              Protocol: SATA
              Internal: Yes
              Partition Map Type: GPT (GUID Partition Table)
              S.M.A.R.T. Status: Verified
    Then I launch VMWare, which uses the Boot Camp drive. The once again run the same command from the Terminal Command and I get this.
    Storage:
        Lion Client:
          Available: 213.39 GB (213,392,244,736 bytes)
          Capacity: 639.28 GB (639,275,270,144 bytes)
          Mount Point: /
          File System: Journaled HFS+
          Writable: Yes
          Ignore Ownership: No
          BSD Name: disk0s2
          Volume UUID: CCB501BF-AF24-30E7-A938-5A4E52DF14D7
          Physical Drive:
              Media Name: WDC WD6400AAKS-41H2B0 Media
              Medium Type: Rotational
              Protocol: SATA
              Internal: Yes
              Partition Map Type: GPT (GUID Partition Table)
              S.M.A.R.T. Status: Verified
    The Boot Camp Drive is no longer listed.
    I assume this is due to the the fact that the drive is "In Use" however is seems odd since the Mac drive is also in use and it appears without problem. I assume there is no "fix" for this, I was just wondering if someone may have an explaination why?
    Also, I do realize that I can query the various interface types like system_profiler SPSerialATADataType to get all the properly installed phycial drives, but then I would have to query all possible interface types, isolate only devices containing Volumes, then consoldate the information to just the information that I need. I was hoping for a cleaner query.

    Thank you for your response.
    VMWare may be the cause, but the actual issue I am having is with Apple's System Information. I anticipated resistance from VMWare if I went to them with a question about an Apple software issue (even though VMWare software is part of the equation). I was trying to avoid the inevitable finger pointing game. I thought I would try with Apple Forums first since the issues presents itself within the Apple Software. However, you are correct that VMWare may have an explanation on why Fusion might be interfering with System Information. I will check with them next.
    To answer your question. Yes, In most cases I do use Fusion to run Windows side-by-side with the Mac OS. However, that is not always the case. There are a few reasons why I have it setup using a Dual Boot configuration.
    One, in some cases, due to the intense programs I occasionally run (graphic applications), I prefer to simply boot straight into Windows via Boot Camp so I may allocate all hardware resources to Windows. Additionally, some graphic applications like to have direct access to hardware and the extra layer of the VM environment can cause problems when an application is trying to directly access specific hardware like a graphics card.
    Second, I often use either side, both Mac and PC, for testing. There is an advantage to not having to rely on the Mac OS to run Windows. If, for whatever reason, my Mac becomes unstable due to testing, I can still jump right into Windows to do work if necessary.
    Third, I love the Mac OS, but I work in a PC centric organization. If there is a "problem" with my system, it is too easy for other system admins to say, "it's because it's a Mac". Having the definitive separation of the OS's allows me to prove that the Mac OS is not a factor.

  • I have iMovie 09. I just erased my external hard drive, but it is still formatted for the mac. However, iMovie will not recognize the hard drive. It shows the only hard drive available is the computers. How do I get the external hard drive to show up?

    I have iMovie 09. I just erased my external hard drive, but it is still formatted for the mac. However, iMovie will not recognize the hard drive. It shows the only hard drive available is the computers. How do I get the external hard drive to show up?

    In Finder's Menu, select Go menu>Go to Folder, and go to "/volumes". (no quotes)
    Volumes is where an alias to your hard drive ("/" at boot) is placed at startup, and where all the "mount points" for auxiliary drives are created for you to access them. This folder is normally hidden from view.
    Drives with an extra 1 on the end have a side-effect of mounting a drive with the same name as the system already think exists. Try trashing the duplicates with a 1 or 2 if there are no real files in them, and reboot.
    If it does contain data...
    http://support.apple.com/kb/TS2474

  • Powerbook G4 10.4.11  won't start from hard drive .  Tried repair, " The underlying task reported failure on exit (-9972).Invalid sibling link,invalid B tree header, invalid map node,invalid record type,the volume needs to be repaired.

    Powerbook G4 10.4.11  won't start from hard drive .  Tried repair, " Invalid sibling link,invalid B tree header, invalid map node,invalid record type,the volume needs to be repaired.Powerbook G4 10.4.11  won't start from hard drive .  Tried repair, " The underlying task reported failure on exit (-9972).Invalid sibling link,invalid B tree header, invalid map node,invalid record type,the volume needs to be repaired.
    The underlying task reported failure on exit (-9972).

    kauribill wrote:
    " The underlying task reported failure on exit (-9972).Invalid sibling link,invalid B tree header, invalid map node,invalid record type,the volume needs to be repaired.
    The underlying task reported failure on exit (-9972).
    This is a directory issue that Disk Utility cannot fix. Although it manifests itself as a software issue sometimes it may be hardware based. See DiskUtility reports "Underlying task reported failure" when repairing avolume http://support.apple.com/kb/TS1901?viewlocale=en_US". You can try using a utility like TechTool Pro, Drive Genius or Disk Warrior to repair and replace the directory. Another option would be to use the Archive and Install feature to reinstall. If the problem returns after correction you may have a failing or failed HDD.
    cornelius

  • Elements 5 will not start from the windows old file after upgrading from vista to win 7

    Elements 5 will not start from windows.old after upgrading from vista to win 7

    Ideally there should not be any impact of OS change, but officially PSE5 is not supported on Win7.
    What exactly happens ? Can you see the processes running in Task-manager?

  • HP dv7 will not recognize second hard drive

    My HP dv7 2185dx running Windows 7 will not recognize second hard drive, bios recognizes it, Intel Rapid storage recognizes it.
    Primary hard drive is a 1TB, in install a second 500GB hard drive.
    This question was solved.
    View Solution.

    Hi,
    Hold down the Windows Key and press R.  Into the Run Box type compmgmt.msc and hit enter.  Click Disk Management in the left pane and let the drives load up. 
    Does the 2nd HDD show here?
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Imac will not see my hard drive on start up, wants to start from network start up disk that does not exist. How to get rid of it? So there is just one choice / my hard drive.

    I have a Intel duo Imac. Everything has been running relatively smoothly for a few years now. All of a sudden my computer will not start. I get the flashing folder with a question mark.
    When I go to Start up disk in my system perfernces while the computer is on. I see 2 possible choices. One is my hard drive with the operating system shown. The other is a non-existant Network Start up disk with a question mark in it ( looks like a hard drive with a question mark and it say's its a "network start up disk).
    All I think I want to do is get rid of the Network startup with the question mark. I can not find anywhere how one can just remove an old or non existant start up disk without reformatting.
    I believe this came from a clients hard drive who had a network system on it. We no longer have that drive. It no longer exists. But a latent icon shows up in start up disk.
    When I go to change the start up disk. I can change it to either the hard drive or the network with the question mark. But when I select my hard drive and then got to restart the computer. I get the flashing folder with a question mark on start up. I have also seen the flashing globe a couple times.
    When I attempt to run disk utility from may install disk ( holding down "C" on start-up ). Disk utility does not see my hard drive. Just the Apple install disk with the disk utility on it.
    What can I do to remedy this short of re-installing? Will a program like Disk Warrior or Tech Tool help?

    Thank you. That's what I thought will need to happen.
    One more question. I tried using the Apple install disk that came with the computer. It's an OS 10.5.6 disk. It does not see my 10.6.8 system internal hard drive to repair. All it see's is itself 10.5.6 disk. Do you think I can use a 10.8+ disk utillity since that is a higher system it will see the 10.6.8. Where the 10.5.6 does not?
    I don't want to turn the computer off for fear I'll get the question mark again. P-Ram got me going last time but for how long I don't know?  It would be nice to be able to turn the computer off for the night and startup as usual to give it a rest and try to reset itself.
    Thanks for your help, I know I will eventually need to re-install. But I am in the middle of a project with tight deadlines and all I can do right now is back-up. Trying to migrate to another computer temporarily to finish the job. That's a lot of extra work in the short time also.
    Just trying to put a band-aid on it for another couple weeks.

  • Intel Xserve will NOT boot from hard disk drive

    I have two Intel Xserves 2.0 QC machines
    I have tried to re-install version 10.4.11 OS (don't ask) onto a Hard disk drive that is in a Disk drive caddy and inserted in the machine.
    When booting from The installation DVD media
    The disk is seen by the "Disk Utility" (the disk is partitioned as GUID boot) and the installation proceeds to the disk.
    Once the first pass of the installation is complete and the system reboots, the system shows the folder and ? mark.
    If I boot and hold "ALT" key to view all avaialble boot options the Hard Disk Drive does NOT appear as valid boot disk.
    It does show, the still inserted Installation DVD.
    I CAN boot from an external firewire drive and the Hard disk drive is visible to the OS once logged in.
    I have tried different caddy postions (left, middle and right)
    I have tried bona fide Apple supplied Disk drives
    I have tried various different caddies
    I have tried installing Operating System 10.5.*  and  10.6.8 server
    I have run SMC reset and system reset
    But still I cannot boot off from any Hard Disk Drive inserted in a caddy at the front of the system.
    Has anyone seen this behaviour?
    Is it fixable?
    Do I have replace something like the Hard Disk Drive back plane circuit board? Or even the main logic board?
    I have now run out of ideas and cannot find any help in discussions or just googling.
    ANY help would be very appreciated
    Regards
    Tony

    Antonio Hi !
    QC = Quad core  or  QX as it is written on the "pull out" serial number tab at rear of system
    I have 3 late 2006 Intel xserves
    On my intial posting I declared 2 were 2.0 machines - when I was trying to be concise
    2 of the macines are 2.66 systems and 1 is 2.0 system - all are QX machines
    the 2.0 and 1 of the 2.66 will NOT boot from the ADM and disk inside the system - whereas the other 2.66 system will.
    I have many different Caddies and these have different product/model number labels
    603-9965
    603-9545
    603-9796
    these are marked "intel SATA"
    The 80Gb was only one of the drives tested - I have used Seagate 400Gb 750Gb and 1Tb  -  all of which have been used in systems at one time or another
    and as I said the drives ARE visible once the operating system (either installation DVD or external firewire are booted from) - they are just NOT visible when the system is searching for boot media.
    Thanks for the guide - I will look through that and continue to try and find an answer

  • BIOS update, then will not boot from any drive

    This old laptop, 3000 C200 8922 was acting very clunky when on wireless.
    Downloaded Bios Version 63ET62WW and flashed it into the bios.
    Now, even though I can get to the bios screen, and it shows the hard drive, DVD/CD drive, it will NOT boot from either.
    It will also "see" a usb installed, but will not boot from it.
    I have removed all power and cleared the CMOS several times and I still have nothing. Tried two different hdd's which have been in the machine and same results. 
    HELP!! I should have never messed with it......

    hi k4pew,
    One rule after a BIOS update is to Load optimize deafults after updating.
       Try that go inside BIOS Hit F9 to load defaults then F10 to Save and Exit.
    If not
    Try turning on the computer and start hitting F1 to load the Recovery Menu and see if that will push then Try Reseting the PC.
    If still the same Im afraid that the BIOS needs to be reflashed.
    Im not aware of any flash tool or a your Previous BIOS Version Firmware available for download.
    You can try calling Lenovo Technical Support for any options available for repair.
    Im sorry to hear what happened
    Regards
    Solid Cruver
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

Maybe you are looking for