BT Hub 3 not working with Vodafone SureSignal 3

I had my Vodafone Sure Signal 3 working fine until 16 December now it will not connect through my BT Infinity HH3.
I have all the Vodafone port forwarding set up as instructed but did not need that before.
Vodafone say it is a repeating problem with BT csutomers and BT say it is not their problem.
Running the Vodafone tracert produces many failures due to time out.
My BB speeds are >37Mb/s down and >7Mb/s up
Where do i go from here?
Any suggestions would be appreciated.

Try a factory reset of the homehub by pressing a pin into the recess button on the rear for about 20 seconds.

Similar Messages

  • BB8830 World EDition - Verizon - Not working with VODAFONE SIM card

    Hi,
    I bought BB8830 world edition from US to India. It works fine with Airtel Network. But its not working With Vodafone SIM card.
    Option--security option-- Certificates-- Vodafone WLTS(x - red cross mark) is there. It expired on 2008.
    Please let me know any one to find out solution for this. whether I need to updated the BB OS or how it works with vodafone SIM..
    Please post the answer in [email protected]  also.
    Thanks in advance.

    If the phone is unlocked, then contact Vodafone.  They are the carrier you are trying to use, so only they can really help you.

  • Unlocked iPhone not working with Vodafone

    Hi all,
    I have an awkward problem. A couple of months ago I bought an unlocked iphone in Italy because I was moving to the Netherlands and I knew they didn't sell unlocked iPhones there. In the meantime I successfully used my Italian prepaid SIM card.
    Now I bought a Vodafone NL SIM card. The first time I tried to use it, I got a No Service message on my iPhone but apparently the SIM was working with another cheap phone that I have. Today I went to the Vodafone store where I bought the SIM and they replaced the SIM card twice. Apparently the last SIM card was working, I could call and receive calls, send and receive text messages.
    Unfortunately, I can use the phone just for 10 minutes, then I get a No Service message. I have to reboot my iPhone and then it works again (for 10 minutes).
    Vodafone told me that they did everything they could and the problem depends on my phone (they even support the iPhone, all the settings are right, but still no luck).
    Do you have any ideas or suggestions? Do you think this problem depends on the iPhone?
    I really don't know what to do and I have a 1 year contract (even if it is only 10 € p/m, it is still annoying).
    Thank you!
    Best,
    Marco

    Hi ashish,
    Did you contact TPG about activating International Roaming before you left for India:
    http://www.tpg.com.au/support/international_roaming.php
    Cheers,
    GB

  • USB hub does not work with iTunes

    I have been trying to add USB ports to may Mac's and am not able to synch through the hub. They are hi speed 2.0 USB hubs by Rocketfish and Belkin. iTunes locks up until I remove them from the USB cable (spinning color wheel) and then iTunes goes back to normal. I have tried with both my 24" Intel iMac (Metal one) and a new 15" Macbook Pro. When I use the USB port on the Mac iTunes works great. There seem to be a ton of USB problems posted and zero answers on how to correct. I have tried with an Color iPOD, iPhone and an iTouch to no avail. Having a couple of USB ports won't work in my situation. Anyone know if Apple has posted a workaround or a real fix anywhere.

    Thanks, I missed where I posted But I tried with my HP - Same issue. I think others have had this. I believe that iTunes is hit or miss on Hubs. I wish I could figure out what makes them a hit - instead of a miss.

  • I have purchased i phone 4s from US .but its not working with vodafone microSIM .can you please tell me whether its hardware or software problem

    please reply me soon..

    i have purchased unlocked iphone
    How do you know that?  Unless you bought it directly from an Apple Store as unlocked, it pprobably isn't or was hacked.  Phones that were hacked to "unlock", often don't work correctly and ALWAYS get re-locked when updated or restored.

  • My itunes 11 Home sharing is not working with my windows 7 PC and iPad it shows up on iPad and when I go to share the music app does loading for 3 mins and crashes I am using a virgin super hub router please please please help

    My itunes 11 Home sharing is not working with my windows 7 PC and iPad it shows up on iPad and when I go to share the music app does loading for 3 mins and crashes I am using a virgin super hub router please please please help

    My itunes 11 Home sharing is not working with my windows 7 PC and iPad it shows up on iPad and when I go to share the music app does loading for 3 mins and crashes I am using a virgin super hub router please please please help

  • HT4061 hi i have purchased iphone4 from vodafone australia 2 years back.it is unlocked, when i went to india .it was not working with any carrier in india.it was displaying no service.is it a problem of iphone or any other anybody please could let me know

    hi i have purchased iphone4 from vodafone australia 2 years back.it is unlocked, when i went to india .it was not working with any carrier in india.it was displaying no service.is it a problem of iphone or any other anybody please could let me know?

    Hi ashish,
    Did you contact TPG about activating International Roaming before you left for India:
    http://www.tpg.com.au/support/international_roaming.php
    Cheers,
    GB

  • USB hub does not work!  Help

    I was attempting to install a KVM switch for my G4 and G5 that required me attaching my keyboard and mouse to the usb port on the back of the monitor.
    The USB hub does not work! Monitor cable has no bent pins, and works perfectly for video with all my Mac's, G4's, G5's. The problem is I have had this monitor awhile and never tried these ports so apple won't help.
    Anyone have any suggestions why these ports don't work and if there is a fix?
    Can any one recommend a KVM switch that supports ADC, and USB so I bypass this hub.
    Thanks

    Some USB 2.0 hardware works very well w/USB 3.0 & some don't.  Suggest that you contact the sound card manufacturer & ask them.  Perhaps they can recommend a work-a-round. 
    Another user posted about the same problem some weeks ago regarding a sound card. 

  • I bought the last apple wire keyboard , but it does not work with my usb ..

    i bought the last apple wire keyboard , but it does not work with my usb hub why ?
    the only way it works its when connecting it thrue my powerbook usb ...
    the problem is i HAVE TO USE IT THRUE AN USB HUB ... do you think its because my hub is cheap ? 10 $ .... i 've been told that it comes from the fact that i need an auto-alimented usb hub ...?.
    suggestions gentlemen ?

    I have eyes everywhere. Two of them can see the word "Paris", right below your name, at left.

  • Is there a USB 3.0 Hub that really works with the Mac Mini?

    My Mac Mini's four USB 3.0 ports work fine with my four USB Seagate GoFlex 3.0 hard drives. The drives mount at startup, and perform at expected USB 3.0 speeds. But, when I connect the drives to a USB 3.0 HUB to free up the Mac's USB ports for other devices, typically two of the USB Seagate drives will mount at startup, but two won't. There's a fix for this: after startup, I simply disconnect AC power from the drives that didn't mount, and reconnect the power a few seconds later. Now all my drives are mounted, they perform properly, and other USB devices connected to other Mac Mini USB ports (a mouse, a USB midi interface) work just fine as well. It's annoying, though, to have to perform this extra disconnect-reconnect step every time. I've tried two different USB 3.0 HUBs -- one from Uspeed and one from Satechi -- and I have exactly the same problem with both. Question: Is anybody else experiencing the same thing with a late 2012 Mac Mini and a USB 3.0 Hub? Has anybody found a 3.0 Hub that doesn't have this issue with the Mac Mini?

    The USB 3.0 hub instability problems extend beyond the Mac-Mini, as addressed below.
    At long last we're seeing progress in getting 2012 Macs to work with USB 3.0 hubs. As discussed on this and other discussion groups I've had a horrible time with my MacBook Pro Retina  being unstable with USB 3.0 hubs. I know many of you have also or you wouldn't be reading this posting. 
    In June 2012 I bought one of the first 2012 MacBook Pro's with a Retina display. It's been a battle since with Apple selling what appears to be an incompatible or unstable system to effectively communicate with the USB 3.0 hubs. You'll see vendors now making comments that Apple is the source of the problem.
    I've been through USB 3.0 issues with two MacBook Pro Retina laptops. I've also tested a Uspeed hub, with 3 portable USB 3.0 drives connected, at the Apple Store. This was on a newer model MacBook Pro Retina, and also on a 27" iMac. All had instances where drives failed to mount during the short period allowed for testing. (Because of time constraints, we were unable to test at the Store for spontaneous and unprovoked unmounting of drives connected to the hub. These problems have existed since the beginning on my rMBP.)
    I am now on my 20th hub that has been purchased, or provided for testing. They varied from 4-Port to 10-Port powered hubs and involved 11 brand names. Comments were posted on Amazon, Tiger, and others for most of the ones purchased, and some that were tested. Some, like the HooToo specifically warned against use with Macs in the manufacturer's manual and, as I learned, for good reason. That was reflected in my comments for the drive on Amazon.
    The Plugable 7-Port USB 3.0 powered aluminum-finish hub that I have been testing since October 13 was provided  by Plugable after the first one, purchased through Amazon, was returned as unreliable. This 3rd, and newer generation Plugable hub uses the VIA VL812 chipset with the new version 90.81 firmware. My experience over the last 4+ weeks with this hub has been solid. While there have been problems with Eject errors, none were traced to the hub electronics. (Problems with intermittent connections at the cable connectors  appeared to be the cause of the disconnect errors. Almost all of the failures were traced to intermittent Micro-B connectors, but that's another story.)
    In addition to the greatly improved reliability of this hub, I find several features of this Plugable to be a plus including:
    The plug engages fully to the "hilt" when plugged into the hub giving a solid connection, as occurs on the MacBook Pro Retina USB 3.0 ports. Others hubs typically had a gap between the "hilt" of the connecting end, and the hub allowing for lateral movement. With some hubs this allowed for intermittent connections if the cable was disturbed.
    The on/off switch on the hub allows the hub to be powered down when not in use.
    The full size Type-B connectors on the cable at the hub end engage solidly. Hubs with Micro-B connectors have presented intermittent connections in the cable connector.
    The aluminum case looks attractive with Macs, IMO, but not a reason to buy.
    Overall, Plugable's support is the best I've encountered. I've found their response to questions to be prompt and thorough. This, coupled with their online support articles has put them at the top of my list. They provide news and information that I've not found with other hub vendors.
    The article titled "Plugable USB 3.0 7 Port Hub Firmware History" at the below link gives insight into the history of the problems that we've been having with the USB 3.0 hubs on Macs and the firmware updates, regardless of the brand of hub you have.  Apparently, if you have the VIA VL 812 chipset, firmware version 85.81, you're in safe territory.
    http://plugable.com/2013/10/30/plugable-usb-3-0-hub-firmware-upgrades2
    (One of the Plugable hubs appears identical to the black 7-Port Uspeed hub, and both use the VIA VL 812 chipset. They appear to be from the same manufacturer with the real difference appearing to be in the VL812 version of the firmware in the hub.)
    Some of the firmware can be upgraded, and some can't. Contact Plugable or Anker if you're affected.
    Uspeed has made improvements, but they were still unstable as of the last one I received for testing. In her last reply on 10/13/13 Sunnie with AnkerDirect Customer Support stated:
    Unfortunately, the new Firmware version (908x) does not work with the model "68UNHUB-B7U" you have. The hub bellow has much less complaints about Mac issue. We suggest that you order this one.
    http://www.amazon.com/gp/product/B009Z9M3DY
    AnkerDirect Customer Support
    Note that the above hub recommended by Anker has an 8th port just for charging iOS devices. Some will see this as a plus. However, the lack of such a port is not seen as a big problem. It's easy and relatively inexpensive to purchase extra 5V power adapters for charging, which is my preference. Plugging and unplugging devices on a hub that is powered "On" presents the potential for movement of the cables. This could interrupt a cable connection  and disconnect a drive during data transfer resulting in corrupted files. With 7 and 10 port hubs, and all the cables needed, this gets risky.
    I believe the USB 3.0 hub issues we're having are the result of poor design of the Mac's USB 3.0 implementation at the start. Unstable hubs that I've had a friend with Windows 7 test, said they "performed like a dream" on his PCs. This indicates the problem is with Macs, not the (twenty) hubs I've used.
    A statement from a support person dealing with USB 3.0 hubs tells what's I've long suspected: " -- the evidence is pointing to something specific to the Apple design (perhaps external to the chipset, like the signal re-driver….."
    If you're having USB 3.0 problems, be sure to let Apple know by sending in a Feedback comment to Apple at:
    http://www.apple.com/feedback/ 
    I'm told they read and treat the feedback seriously (although the duration of this USB 3.0  problem makes me wonder if Mavericks and iOS 7 haven't had a higher priority and distracted from this. Microsoft got USB 3.0 right, how about it Apple?)

  • ISight is not working with boot camp

    Hi,
    I have a Macbook Pro and very satisfied with it. Formerly I worked with Windows XP, so I decided to buy a Macbook and use boot camp. Everything was fine. In my enthusiasm I bought the LED cinema display. Very good display but the iSight camera is not reliable working with boot camp. There is no driver available. Sometimes the camera is recognized as video device but mostly not. When the camera is not recognized then there is a yellow exclamation mark in the device manager. I don't know what to do. Is anybody working with boot camp and the iSight build in the LED cinema display? And what driver do you use? Hopefully I get some help here. Everything is working convenient except this issue.
    Thank you, Frank

    Sorry, I think I mixed some things. I tried several contellations to find out what is going wrong. The iSight is woking with my MacBook (and boot camp). But it is not working with other Laptops or PCs (all with Windows XP). It is working really rarely but not reliable and not replicatable. In all cases I tried only the USB connector from the LED cinema display. Audio, micro and hub is always working without problems. The iSight driver delivered with the Macbook is not working (only with the Macbook itself). If I had known this before I think I would buy the display although. The display is great. But it is a pity that the iSight is not working when you do not use Apple hardware. May be I will buy the Mac Pro in one or two years when I need a new PC. Perhaps someone can answer if Windows XP is working without problems on a Mac Pro? And is the iSight build in the LED cinema display working (Mac Pro and boot camp)?
    Frank

  • Camera connection not working with my camera

    Camera connect not working with my Sony boggie camera

    The Bloggie will not work because it draws too much power from the USB port on the iPad.  The solution is to interpose a powered USB hub between the Bloggie and the iPad - connect the Bloggie to the powered hub, then connect the hub to the ipad accessory.  Works fine with my 3D Bloggie.

  • C3 did not work with all the types of routers

    Hi!
    My problem is with the C3 (Hungarian 03.36 Vodafone), that the e-mail program is not working with all the wlan routers. My home router is Asus WL-520GC and with it I get communication error, but with a Linksys or a Tplink router everything is good. How can it be?
    (I ve heard it from outhers too)
    (both WPA2personal and DHCP)
    I tried it with factory settings, but same problem: communication error.
    Pls help! 

    Solved: I had to upgrade the firmware of the router.
    It works

  • I have recently upgraded my iMac Intel G5 iSight to OS 10.6.8 and now the internal mic does not work with skype or facebook. I can here static when playing back clips. Do I need to update firmware or reload old sys parts

    I have recently upgraded my iMac Intel G5 iSight (iMac5,1) to OS 10.6.8 and now the internal mic does not work with skype or facebook. I can here static when playing back clips. Do I need to update firmware or reload old system parts. I have zapped PRAM. The blue indicator in system audio panel will appear for a second as I slide the bar for internal mic but then it disappears. Is there a fix?

    The sound seems very faint but can here static on playback.

  • My operating system windows XP not working with photoshop cloud, why not?

    I need to add 2 more licences for photoshop cloud and I'm being told my operating system windows XP does not work with Photoshop cloud. We already have 2 pcs using it in our office so why not?
    Please help
    Roy

    Do you have the latest version of iTunes?  If not, get it at:
    http://www.apple.com/itunes

Maybe you are looking for