Cables to connect X-Fi I/O Drive to X-Fi Titanium

Hi,
Does anyone know where I can get replacement?cables?DID_EXT and?AND_EXT from? They are used to?connect X-Fi I/O Dri've to X-Fi Titanium. Creative is saying they dont sell them, I searched the internet but I coudnt find any vendor which sells them.
Without the cables my I/O dirve is useless.
Any ideas?
thanks
Raf

I have been looking on ebay for some time?but had no luck.. You would think that this kind of items should be easily available from creative but unfortunately is not the case. If you?lose or damage the cable the I/O dri've became uselsss...

Similar Messages

RS480M2-IL: Drives do not power up if PATA cables are connected

I am building a system around a the RS480M2-IL and I'm having a bizzare problem.
When I plug the hard drive and DVD into the power supply and turn the system on without connecting the ATA133 connectors, the drives power up. If I connect the drives to an other system, both are detected and usable. I've tried a different ATA133 cable and using either PATA controller on the motherboard. The drives work fine and the power supply works fine, but when the drives are connected to the ATA133 connector, either together or seperately, they are unable to recieve power.
Do you know what could be causing this? The only thing I can think of is a defective IDE controller on the motherboard.

Make sure the integrated IDE controllers you are trying to use are enabled in the BIOS. You will want to put the optical drive on one IDE controller and the hard drive on the other. i.e. don't have them both connected on a single cable. Check the settings - both should be on master or cable select.

Connect Encore with external hard drive through micro USB OTG cable

Hi
I am using a micro USB OTG cable to connect the encore with a (get this) toshiba 1TB external hard drive, but when i connect the two, the hard drive connects and then reconnects every 5 to 10 seconds ... and this goes on constantly. This is getting beyond frustrating. Any suggestions ?

Yea, it's not gonna power anything that needs 2 USB ports as such need more than 500ma. There may well be a low power USB2 spec for tablets Jerry, but what I meant to refer to us the common 500ma standard USB port spec that device manufacturers generally expect. Sorry for being misleading. Basically one can expect issues from any port designed lower than the 500ma spec but I am sure the Encore is designed for the 'full' 500ma, so any example putting out less is below the designed spec. I still suspect the OTG cable first though.

I will be using a HDMI cable to connect an Apple TV box and a Comcast cable TV box to my TV. My TV has only one HDMI port.

I will be using a HDMI cable to connect an Apple TV box and a Comcast cable TV box to my TV. My TV has only one HDMI port.
To do this I will need a 2x1 HDMI splitter or a 2x1 HDMI auto switch (preferred).
?Is there any Apple TV HDMI port voltage?
When using a HDMI auto switch to connect two devices to a HDMI TV, the
Auto switch cable box only works for components that do not output continuous voltage over HDMI port when turned off.
Do you know of any other solutions? Componets? Actual expierances?
Full text below.
Cable : HDMI switches expand the number of available HDMI ports on a high definition television allowing connection of cable boxes, Blu-ray players, and game consoles. A side benefit is that cable clutter is also eliminated by running a single HDMI cable to your HDTV from a switch and relocating the HDMI ports to a concealed location. The problem with most HDMI switches is that you have to either get up to push a button, or hunt for the remote control, to switch sources. The true mark of any great switching component is an ability to perform its function and remain transparent in its operation. This automatic HDMI switch is a plug-and-play away from offering everything you are looking for in an HDMI switch. Select a single output from up to three devices for signal delivery to your HDTV. Smart operation provides complete control for connect-and-forget operation. Powering on a device gives it output priority over the other devices. By powering down the device in use, output priority is returned to the last powered on device. Note: Auto switch function only works for components that do not output continuous voltage over HDMI port when turned off.
Here is a typical HDMI 3-in 1-Out HDMI Auto Switch
http://www.google.com/products/catalog?q=hdmi+auto+splitter&rls=com.microsoft:en -us&oe=UTF-8&startIndex=&startPage=1&rlz=1I7GGLF_en&um=1&ie=UTF-8&tbm=shop&cid=1 0340892278237558532&sa=X&ei=fTPmTtOiHuXq0gGc3sHfBQ&ved=0CHsQ8wIwAA#
Thanks for any help. Sincerely,
HDMI auto switch?

Hi Erico,
I tried what you said again but without success. I even updated the driver so that that audio driver is the same as the graphics driver i.e.. NVIDIA but this has not helped either:
Do you have any other ideas?
Many many thanks,
Louise

As a Verizon FIOS client, can we just use Ethernet cable to connect to time capsule, or do we need their router to connect to the time capsule?

As a Verizon FIOS client, can we just use Ethernet cable to connect to time capsule or do we need the Verizon router to connect to time capsule?

The Time Capsule is indeed a wireless router with simultaneous dual band capability...and a hard drive for backup purposes. You can use that to your advantage if you configure the Time Capsule as I suggested in Bridge Mode.
The Time Capsule will provide a 802.11n 5 GHz band and a 802.11n/g/b compatible 2.4 GHz band to allow virtually any device to connect to the network.
I suppose that you could also use the "g" wireless network provided by the Verizon router as a "guest" network or something similar if you really do need another wireless network.
It might be possible to configure the Time Capsule as the main router on the network....that's a question for Verizon. But even if you might be able to do this, I'm sure it is not supported by Verizon, so you would be on your own in the event of any Internet connection difficulties on your service.
And, since the Time Capsule does not have a built in modem....you would still need to add a separate modem to the installation anyway.
That's why my suggestion is to use the Verizon device as the "modem" and let the Time Capsule provide the dual band wireless network and of course, handle the Time Machine backups.

Help me find & order best cable to connect MacBook Pro 10.7.5 to Zenith HDTV? Time sensitive!

I am having trouble not having the right cable when connecting my MacBook Pro 10.7.5 OS X to my Zenith 50" flatscreen HDTV- the laptop was purchased in July, and HDTV is one year old. I moved to Central America (Belize) in August, so am lacking in tech support or purchasing options here, and I only know just enough to be dangerous--I am a relatively new Mac user. I just found out I have a friend coming to visit in 10 days who can bring something if I can get it to her! It would take me days to research and decide what I might need, and then it might still not be right. I thought you guys might help me find something quickly.
The cables I brought have allowed video but not sound, and I would like to order whatever I may need online and have delivered to her to bring with her when she comes, making us somewhat short on time. Bear with me while I try to describe what I have. On the Mac, I have a couple different ports that I am unsure what they are called (along with the usual 2 USB ports). One has the lighting strike symbol next to it, the other looks like a little cheerleader with her arms & pom poms in the air, and the third is the flat one that I used to be able to use to connect my (now gone) iPhone. The MacBook does not have an HDMI port. On the Zenith HDTV, I have the usual AV in-ports, and HDMI ports, and a port that looks like an HDMI port only more square.
Just a side note, my husband also has a 6 month old Ipad and we do have the little pigtail to use to hook it up to the TV which works great for the iPad, but I would prefer to use my MacBook so we can watch the movies we put on an external hard drive before moving. I am unsure exactly what cord I need, only that what I brought with me to Belize is not what I need, and apparently can't be found here-no one carries Mac stuff even in the capital city of Belmopan.
(I also have a cranky older 13" mid-2009 model MacBook pro 10.6.8 OS X I have quit using cuz it's quirkly-- that doesn't produce sound through the tv either--but doesn't have the same ports as the new Mac --if there is something we can use to hook it up, that would be great too-I would order both, then I could leave that as a dedicated movie/internet tv box)
Any help, descriptions or pictures or links to what I might be able to order to make either one work and have delivered quickly so she could bring would be GREATLY APPRECIATED. You guys Rock!

You need two things: a mini-Displayport to HDMI adaptor, and a regular HDMI cable.
The mini-Displayport connector on the Macbook is the one you've described with the lightning bolt. That port on your Macbook is actually called Thunderbolt, but for this purpose it's acting as a mini-Displayport connector.
When you buy the Displayport adaptor, make sure you get one that supports audio. Not all do.
I'm sorry I don't know the best options available to you in Belize, but hopefully that information will help you approach a local electronics supplier.
Matt

Need help on connecting USB: 300GB external hard drive to wireless router

Hello,
I am trying to connect USB2.0 Maxtor 300GB external hard drive to my wireless router. Tried using Linksys new product NSLU2 which allows any USB cable external hard drive to NSLU2 device/network storage hub and then connect this NSLU2 directly to wireless router with the help of 10/100 Ethernet cable which allows to access external hard drive wirelessly.
Unfortunately Linksys NSLU2 is designed to supports USB external drives up to 250GB only.
Can any one advice me if there is any device I can use to connect my external hard drive to wireless router and access files without connecting/carrying USB external drive?
Any help is greatly appreciated.
Thanks in advance!
Arvind

Have a look at http://www.ximeta.com and their solutions. Especially
http://www.ximeta.com/web/products/ndenclosure1_en.php might be interesting, as you already have a HD.
Regards, Martin

Connecting Yaskawa Sigma II Servo Drive (SGDH) to PCI-7344 and UMI-7774

Hi,
I have NI PCI-7344 and UMI-7774 and i want to
Connect the UMI-7774 to Yaskawa Sigma II Servo Drive (SGDH) , the servo motor drive is connected to the servo motor with original Yaskawa cables.
1.  do you know if National instruments provide special cables to connect the UMI-7774 to the Yaskawa Sigma II Servo Drive (SGDH) ?
     i know there is special cable to connect this servo drive to the NI PCI-7390
     http://zone.ni.com/devzone/cda/tut/p/id/5908
(you can find in this link that this cable exist: 50 Pin cable for connecting MCA-7790Y to Yaskawa Sigma II Servo Amplifier)
     but this is not the case here, i need to connect the Servo Drive to the UMI-7774..
2. Where can i find a tutorial on how to configure the PCI-7344 in MAX to send simple commands to the Servo Drive
      i.e. to run the servo motor from position A to position B (10,000 encoder pulses)
i'll be gratefull for any help
Regards
Moti

Hi MotiM,
We do not have a cable that will let you directly connect the UMI-7774 to a Yaskawa Drive. We do sell cables that will have the Dsub connector to match the UMI-7774 with pigtails to wire to the drive. If you take a look at the product page for the UMI-7774 you can see the different cables listed under the accessories.
To perform a simple move in Measurement and Automation (MAX) is very simple. In MAX under NI-Motion select your PCI-7344. Under this section select the settings option (by default it will be called Default 7340 settings). Select the Servo radio button. Initialize your controller. Then you can select Interactive and 1-D Interactive and command your motor from there. I have attached an image with the important areas highlighted for you.
Message Edited by Adam_H on 09-19-2008 03:41 PM
Adam H
National Instruments
Applications Engineer
Attachments:
MAX.jpg ‏93 KB

B85-G43 A2 boot error when connecting more then one SATA driver

Hello everyone please help me.
As the title says, whenever i connect more than one sata driver (hdd or dvd) i get te A2 boot freeze....
Already changed cables, hard drives, and problem persist!
Sorry for my bad english, not my main language.
Board: MSI b85-g43
Bios: c.40
VGA: amd 7970 black edition
PSU: xfx pro1000w
Intel Core i5-4670K
MEM: HyperX 1600 8gb
HDD: kingston 120gb ssd and two SATAS
OS: Windows 7 64bit Ultimate

Svet, thx for replying.
I'm a noob here and have some doubts about this steps...
1.) >>Use the MSI HQ Forum USB flasher<< (Ok got it.)
A.) Download the attached archive and place it on your desktop. Do not decompress. (Ok got it)
B.) Download and install the Forum flash tool. (MSI HQ Forum USB flasher?)
C.) Insert your FAT32 formatted usb stick. (Ok got it)
D.) Make sure that all win 8 options are disabled. (Fast Boot etc) Also make sure the legacy USB is enabled. (win 8 options??? i'm running on a win7 ultimate 64bit)
E.) Start the forum flash tool and select option 1. Then point the tool at the compressed archive we downloaded earlier. Then to your USB Flash Drive. (Ok got it.)
F.) Boot to the USB and follow the directions. MEMTEST is included with the forum flash tool and it is recommended to run this prior to any flash. (ok got it, change boot sequence to USB and follow the directions.)
Yeah i know a lot of doubts, sorry for that, Working all day and at night i have to go to the university.
Thank you for your time!!!

5140i - c42 cable - not connecting

Have checked similar threads on this topic and no answer to my problem. Have checked that keyboard lock is not automatically on and set Com port to 30 as recommended in one of the threads.
Running XP Pro, latest service pack.
Latest edition of PC suite downloaded and installed - not drivers on CD that came with the Nokia cable since PC suite has drivers.
When phone is connected 2 error messages appear in quick succession - Data enhancement connected - Enhancement not supported.
Driver disc that came with cable has instructions for setting up modem - have tried to follow instructions but some bear little resemblance to what i see on my machine

Sounds like either a faulty cable or a faulty phone. It should not say "enhancement not supported"... if it does, you've got a problem.
I'd suggest taking your phone and cable to your nearest Nokia engineer to have them both tested.
If you're in the UK, find your nearest engineer here

Difference between using app server connection pooling and using the driver

Hi all,
How to get connection pooling with out application server and tomcat also?
What is the difference between using app server connection pooling and using the driver supported connection pooling?
Regards,
Murali

maybe the performance of App server pool is better than the JDBC pool,
for you don't know wether the implementation of the JDBC interface is good or bad.

Macbook Pro 2011 DVI HDMI out does not work with TV when the power cable is connected

My Macbook Pro (Early 2011) DVI HDMI out does not work with TV when the power cable is connected. If get the blue screen and then can use the macbook but nothing is displayed on the TV. If i go into display I can see that there are two screens but nothing displayed on the TV. If i take the power cable out at this point the TV shows the second desktop as expected. If i then reconnect the cable, the screen flickers, as though it is being affected by the power cable, and the screen goes blank on the TV. Only if i remove the DVI cable do i get the blue screen again. If i remove the power cable and reconnect it will do it every single time, so i cannot see it being a TV issue or a minor glitch.
I have had this working previously but at the minute it seems to not be playing ball....any thoughts
Thanks
Dan

BUMP
Any ideas?

Macbook pro wont connect to internet using cable, but connects using wifi fine

My macbook pro wont connect to the internet using a cable, but connects using wifi fine. I use wifi at home but sometimes need to use my laptop at work and connect using a cable but it says i'm not connected to the internet?

Can you open a terminal and invoke the following commands:
ping -c 10 localhost
and
ping -c 10 google.com
You should normally get something like:
PING google.com (74.125.224.103): 56 data bytes
64 bytes from 74.125.224.103: icmp_seq=0 ttl=55 time=19.053 ms
64 bytes from 74.125.224.103: icmp_seq=1 ttl=55 time=37.692 ms
64 bytes from 74.125.224.103: icmp_seq=2 ttl=55 time=46.988 ms
64 bytes from 74.125.224.103: icmp_seq=3 ttl=55 time=33.466 ms
64 bytes from 74.125.224.103: icmp_seq=4 ttl=55 time=28.940 ms
64 bytes from 74.125.224.103: icmp_seq=5 ttl=55 time=58.070 ms
64 bytes from 74.125.224.103: icmp_seq=6 ttl=55 time=33.335 ms
64 bytes from 74.125.224.103: icmp_seq=7 ttl=55 time=33.361 ms
64 bytes from 74.125.224.103: icmp_seq=8 ttl=55 time=36.099 ms
64 bytes from 74.125.224.103: icmp_seq=9 ttl=55 time=41.111 ms
--- google.com ping statistics ---
10 packets transmitted, 10 packets received, 0.0% packet loss
round-trip min/avg/max/stddev = 19.053/36.811/58.070/9.939 ms

Which adapter or cable for connection from apogee condenser mic to ipad 4 retina display 16 gb wi-fi?

hello
i ve got an apogee condenser mic to record my acoustic guitar and singing. in box there was a cable for connection to ipad&iphone. but that cable was not able to plug in to my ipad 4 (retina display 16 gb wi-fi).i need an adapter or an another cable to plug in the microphone into ipad.but which pin?which kind of adapter?thank u

Hi,
You need a Lightning adapter with 30 pin...

There's any cable to connect my iPhone 4S with the TV

I have not any apple tv or something like that! I'm only asking about any cable to connect my iPhone 4S to my PanasonicTV.
Thanks at all!

Hi - there are several cables available - here are 3 examples:
This one is from Apple:
http://store.apple.com/us/product/MC748ZM/A/apple-composite-av-cable
This is from Belkin:
http://www.expansys-usa.com/belkin-iphone-ipod-av-cable-193150/?utm_source=googl e&utm_medium=shopping&utm_campaign=base&mkwid=svHjLhmZB&kword=adwords_productfee d&gclid=COiMhrDmkLQCFQU5nAodNhUA7g
This is from Best Buy:
http://www.bestbuy.com/site/Electronics-Promotions/Connect-iPhone-iPad-to-TV/pcm cat242400050009.c?id=pcmcat242400050009

Cables to connect X-Fi I/O Drive to X-Fi Titanium

Similar Messages

Maybe you are looking for