Can Apple replace my macbook pro (mid 2012) retina's battery if I think that the battery health has gone bad/in need of and renewal?
Can Apple replace my macbook pro (mid 2012) retina's battery if I think that the battery health has gone bad/in need of and renewal???
I've had my Macbook for about 11 months now and i use it every day; its gone though about 420 cycles of charging and using the power, and i noticed the battrey preformance has decreased (as expected). The problem isn't sevear yet but it would comfort me knowing that i could replace the battery in the near future
Please contact me or answer the question if you know anything about this!
Exitio\'s Apple wrote:
Can Apple replace my macbook pro (mid 2012) retina's battery if I think that the battery health has gone bad/in need of and renewal???
No only if they think under warranty/AppleCare, but your likely able to pay for a new battery if they have them, which they might not yet since it's such a new machine still.
BTW, I have a Early 2011 17" MBP, 27 months old, charges to 97% and has only 14 cycles.
Similar Messages
-
Can I use my macbook pro mid 2012 as an external display using thunderbolt port
Hi,
I want to use my macbook pro (mid 2012) screen as an external display for a raspberry pi using a HDMI to Thunderbolt cable, via the thunderbolt port on the macbook pro. Would this be possible? Can the macbook pro's thunder bolt port act as an input and is any additional software required?
I look forward to hearing from you.
Thanks in advance!Welcome to Apple Support Communities
You are referring to Target Display mode. Target Display mode can only be used in 27-inch iMacs and iMacs with Thunderbolt, not MacBooks Pro > http://support.apple.com/kb/PH11302
Unfortunately, you can't use the MacBook Pro as a display. It doesn't support the monitor mode -
MacBook Pro Mid 2012 Retina Freezes
Hey everyone, my MacBook Pro Retina freezes inconsistently, making it very hard to find the cause of the problem. What happens is all apps seem to be running fine until one app suddenly stops responding properly or doesnt close. From then on all applications exhibit the same behaviour and although I can switch between apps, I cant quit/force quit any apps or restart the computer. Basically every function I try to click is available to navigate to and select until I actually click it, at which point the spinning beach ball appears.
I have noticed it happens most frequently when using Google Chrome. I open a new tab and instead of showing my new tabs page it will show a blank page. If i try to load a website, nothing happens. The application itself stays open, I can move around to a different app, but as soon as I try to close it, it will give me a spinning beach ball, as does every other application.
Annoyingly, this problem occurs on an inconsistent basis and has suddenly begun a month ago, so finding the application causing it is quite difficult. I can go for weeks without a problem, but then have 3 problems the same day. On average it occurs once every 2-3 days though.
I would be very happy for any information or help towards this.This kind of behavior usually indicates a memory fault.
Make a "Genius" appointment at an Apple Store, or go to another authorized service center.
Back up all data on the internal drive(s) before you hand over your computer to anyone. There are ways to back up a computer that isn't fully functional — ask if you need guidance.
If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present.
Keeping your confidential data secure during hardware repair
*An SSD doesn't need to be zeroed. -
Rubber Feet on Macbook Pro mid 2012 Replacement
One of the rubber feet on the bottom of my Macbook Pro mid 2012 Retina fell off and I would like to replace it. Only parts I can seem to find online are for the entire bottom case (which I don't need) or for non-retina feet. Anyone have this same problem and have a way to just fix the one rubber piece?
Thanks.I have a late 2011 MBP and my rubber 'feet' don't slip on my Formica desk surface. It could be that yours are thinning out, I suppose. Some people have had luck with Apple replacing the feet only while others have had to have the bottom casing replaced, feet and all.
Try taking your unit into your local Apple Store and see what they can do for you. I'm sure that they'll charge you something but if it's only for the rubber disks, it shouldn't be much.
Clinton -
Since installing os x mavericks can't shutdown macbook pro(mid 2012) is there a fix?
since installing os x mavericks can't shutdown macbook pro(mid 2012) is there a fix?
I did the SMC reset and that did shut down the computer (did not notice if the power adaptor lite blinked) when pushed power button (after waiting approx. 30sec.) to see if computer would display same message -- it did! Here is report:
Anonymous UUID: B6EB39B0-68CD-8AF4-830E-48E1B18542FD
Wed Nov 27 12:20:53 2013
panic(cpu 0 caller 0xffffff8029adc19e): Kernel trap at 0xffffff8029a50944, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0x0000000000000008, CR3: 0x000000002c033000, CR4: 0x00000000001606e0
RAX: 0x0000000000000000, RBX: 0xffffff80358b7fd8, RCX: 0x0000000000000000, RDX: 0xffffff802a0cb940
RSP: 0xffffff80a2c63a00, RBP: 0xffffff80a2c63a30, RSI: 0xffffff80358b7000, RDI: 0xffffff802c4a1360
R8: 0xffffff802a0d2b30, R9: 0x0000000000000000, R10: 0xffffff80a2c63990, R11: 0xffffff802a089ce8
R12: 0xffffff80358b7008, R13: 0x0000000000000000, R14: 0xffffff80358b7000, R15: 0xffffff802c4a1360
RFL: 0x0000000000010246, RIP: 0xffffff8029a50944, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x0000000000000008, Error code: 0x0000000000000002, Fault CPU: 0x0
Backtrace (CPU 0), Frame : Return Address
0xffffff80a2c63690 : 0xffffff8029a22f69
0xffffff80a2c63710 : 0xffffff8029adc19e
0xffffff80a2c638e0 : 0xffffff8029af3606
0xffffff80a2c63900 : 0xffffff8029a50944
0xffffff80a2c63a30 : 0xffffff8029a5151a
0xffffff80a2c63b10 : 0xffffff8029e836e6
0xffffff80a2c63b30 : 0xffffff7faa4b7614
0xffffff80a2c63b60 : 0xffffff7faa49f90b
0xffffff80a2c63b80 : 0xffffff8029e4c3d3
0xffffff80a2c63bb0 : 0xffffff8029e4c24d
0xffffff80a2c63bd0 : 0xffffff8029e61e74
0xffffff80a2c63bf0 : 0xffffff8029e90e44
0xffffff80a2c63c70 : 0xffffff8029e90477
0xffffff80a2c63cb0 : 0xffffff8029e9020a
0xffffff80a2c63d10 : 0xffffff8029e917dc
0xffffff80a2c63d20 : 0xffffff7faa44772a
0xffffff80a2c63d40 : 0xffffff7faa7a9b46
0xffffff80a2c63d80 : 0xffffff7faa7a95b6
0xffffff80a2c63de0 : 0xffffff7faa79f980
0xffffff80a2c63e20 : 0xffffff7faa7a23a9
0xffffff80a2c63e70 : 0xffffff8029e9fe19
0xffffff80a2c63f00 : 0xffffff8029e98b6b
0xffffff80a2c63f20 : 0xffffff8029a4a15a
0xffffff80a2c63fb0 : 0xffffff8029ad6aa7
Kernel Extensions in backtrace:
com.apple.iokit.IOUSBFamily(650.4.4)[972D3024-AF9C-3E09-A9EC-D9AB2A559B38]@0xff ffff7faa433000->0xffffff7faa491fff
dependency: com.apple.iokit.IOPCIFamily(2.8)[447B4896-16FF-3616-95A2-1C516B2A1498]@0xffffff 7faa0ba000
com.apple.driver.AppleUSBHub(650.4.4)[1229941E-4CB9-3F57-B0A6-4A0AD595025D]@0xf fffff7faa79d000->0xffffff7faa7b3fff
dependency: com.apple.iokit.IOUSBFamily(650.4.4)[972D3024-AF9C-3E09-A9EC-D9AB2A559B38]@0xff ffff7faa433000
com.Ralink.driver.RT2870USBWirelessDriver(4.2.6)[2F28A586-61E4-9821-20DE-488AC0 641892]@0xffffff7faa49e000->0xffffff7faa535fff
dependency: com.apple.iokit.IONetworkingFamily(3.2)[1EAD69CB-6AB4-387F-94C4-8FAAFF28354C]@0 xffffff7faa3ff000
dependency: com.apple.iokit.IOUSBFamily(650.4.4)[972D3024-AF9C-3E09-A9EC-D9AB2A559B38]@0xff ffff7faa433000
BSD process name corresponding to current thread: kernel_task
Mac OS version:
13A603
Kernel version:
Darwin Kernel Version 13.0.0: Thu Sep 19 22:22:27 PDT 2013; root:xnu-2422.1.72~6/RELEASE_X86_64
Kernel UUID: 1D9369E3-D0A5-31B6-8D16-BFFBBB390393
Kernel slide: 0x0000000029800000
Kernel text base: 0xffffff8029a00000
System model name: MacBookPro9,2 (Mac-6F01561E16C75D06)
System uptime in nanoseconds: 82652072793
last loaded kext at 30378600712: com.apple.driver.AudioAUUC 1.60 (addr 0xffffff7fab05c000, size 32768)
loaded kexts:
com.Ralink.driver.RT2870USBWirelessDriver 4.2.6
com.apple.driver.AudioAUUC 1.60
com.apple.driver.AGPM 100.14.11
com.apple.driver.ApplePlatformEnabler 2.0.9d1
com.apple.driver.X86PlatformShim 1.0.0
com.apple.filesystems.autofs 3.0
com.apple.iokit.IOBluetoothSerialManager 4.2.0f6
com.apple.driver.AppleMikeyHIDDriver 124
com.apple.driver.AppleHDAHardwareConfigDriver 2.5.2fc2
com.apple.driver.AppleHDA 2.5.2fc2
com.apple.iokit.IOBluetoothUSBDFU 4.2.0f6
com.apple.iokit.IOUserEthernet 1.0.0d1
com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport 4.2.0f6
com.apple.driver.AppleUpstreamUserClient 3.5.13
com.apple.driver.AppleLPC 1.7.0
com.apple.driver.AppleSMCLMU 2.0.4d1
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.AppleHWAccess 1
com.apple.driver.AppleSMCPDRC 1.0.0
com.apple.driver.AppleThunderboltIP 1.0.10
com.apple.driver.SMCMotionSensor 3.0.4d1
com.apple.driver.AppleMikeyDriver 2.5.2fc2
com.apple.driver.AppleIntelHD4000Graphics 8.1.8
com.apple.driver.AppleIntelFramebufferCapri 8.1.8
com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0
com.apple.driver.AppleMuxControl 3.4.12
com.apple.driver.AppleBacklight 170.3.5
com.apple.driver.AppleMCCSControl 1.1.12
com.apple.driver.AppleUSBTCButtons 240.2
com.apple.driver.AppleUSBTCKeyEventDriver 240.2
com.apple.driver.AppleUSBTCKeyboard 240.2
com.apple.driver.AppleIRController 325.7
com.apple.driver.AppleFileSystemDriver 3.0.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 35
com.apple.iokit.SCSITaskUserClient 3.6.0
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCIBlockStorage 2.4.0
com.apple.driver.AppleUSBHub 650.4.4
com.apple.driver.AppleSDXC 1.4.0
com.apple.driver.AirPort.Brcm4331 700.20.22
com.apple.driver.AppleFWOHCI 4.9.9
com.apple.iokit.AppleBCM5701Ethernet 3.6.9b9
com.apple.driver.AppleAHCIPort 2.9.5
com.apple.driver.AppleUSBEHCI 650.4.1
com.apple.driver.AppleUSBXHCI 650.4.3
com.apple.driver.AppleSmartBatteryManager 161.0.0
com.apple.driver.AppleRTC 2.0
com.apple.driver.AppleACPIButtons 2.0
com.apple.driver.AppleHPET 1.8
com.apple.driver.AppleSMBIOS 2.0
com.apple.driver.AppleACPIEC 2.0
com.apple.driver.AppleAPIC 1.7
com.apple.driver.AppleIntelCPUPowerManagementClient 216.0.0
com.apple.nke.applicationfirewall 153
com.apple.security.quarantine 3
com.apple.driver.AppleIntelCPUPowerManagement 216.0.0
com.apple.kext.triggers 1.0
com.apple.iokit.IOSerialFamily 10.0.7
com.apple.driver.DspFuncLib 2.5.2fc2
com.apple.vecLib.kext 1.0.0
com.apple.iokit.IOAudioFamily 1.9.4fc11
com.apple.kext.OSvKernDSPLib 1.14
com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.2.0f6
com.apple.iokit.IOBluetoothFamily 4.2.0f6
com.apple.iokit.IOFireWireIP 2.2.5
com.apple.driver.AppleThunderboltEDMSink 1.2.1
com.apple.driver.AppleThunderboltDPOutAdapter 2.5.0
com.apple.driver.AppleSMBusPCI 1.0.12d1
com.apple.driver.AppleHDAController 2.5.2fc2
com.apple.iokit.IOHDAFamily 2.5.2fc2
com.apple.iokit.IOSurface 91
com.apple.iokit.IOAcceleratorFamily2 98.7.1
com.apple.AppleGraphicsDeviceControl 3.4.12
com.apple.driver.IOPlatformPluginLegacy 1.0.0
com.apple.driver.X86PlatformPlugin 1.0.0
com.apple.driver.AppleSMC 3.1.6d1
com.apple.driver.IOPlatformPluginFamily 5.5.1d27
com.apple.driver.AppleGraphicsControl 3.4.12
com.apple.driver.AppleBacklightExpert 1.0.4
com.apple.iokit.IONDRVSupport 2.3.6
com.apple.driver.AppleSMBusController 1.0.11d1
com.apple.iokit.IOGraphicsFamily 2.3.6
com.apple.driver.AppleUSBMultitouch 240.6
com.apple.driver.AppleThunderboltDPInAdapter 2.5.0
com.apple.driver.AppleThunderboltDPAdapterFamily 2.5.0
com.apple.driver.AppleThunderboltPCIDownAdapter 1.4.0
com.apple.iokit.IOUSBHIDDriver 650.4.4
com.apple.driver.AppleUSBMergeNub 650.4.0
com.apple.driver.AppleUSBComposite 650.4.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.6.0
com.apple.iokit.IOBDStorageFamily 1.7
com.apple.iokit.IODVDStorageFamily 1.7.1
com.apple.iokit.IOCDStorageFamily 1.7.1
com.apple.iokit.IOAHCISerialATAPI 2.6.0
com.apple.iokit.IOSCSIArchitectureModelFamily 3.6.0
com.apple.driver.AppleThunderboltNHI 1.9.2
com.apple.iokit.IOThunderboltFamily 2.8.5
com.apple.iokit.IO80211Family 600.34
com.apple.iokit.IOFireWireFamily 4.5.5
com.apple.iokit.IOUSBUserClient 650.4.4
com.apple.iokit.IOEthernetAVBController 1.0.3b3
com.apple.driver.mDNSOffloadUserClient 1.0.1b4
com.apple.iokit.IONetworkingFamily 3.2
com.apple.iokit.IOAHCIFamily 2.6.0
com.apple.iokit.IOUSBFamily 650.4.4
com.apple.driver.AppleEFINVRAM 2.0
com.apple.driver.AppleEFIRuntime 2.0
com.apple.iokit.IOHIDFamily 2.0.0
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.sandbox 278.10
com.apple.kext.AppleMatch 1.0.0d1
com.apple.security.TMSafetyNet 7
com.apple.driver.AppleKeyStore 2
com.apple.driver.DiskImages 371.1
com.apple.iokit.IOStorageFamily 1.9
com.apple.iokit.IOReportFamily 21
com.apple.driver.AppleFDEKeyStore 28.30
com.apple.driver.AppleACPIPlatform 2.0
com.apple.iokit.IOPCIFamily 2.8
com.apple.iokit.IOACPIFamily 1.4
com.apple.kec.pthread 1
com.apple.kec.corecrypto 1.0
Model: MacBookPro9,2, BootROM MBP91.00D3.B08, 2 processors, Intel Core i5, 2.5 GHz, 4 GB, SMC 2.2f44
Graphics: Intel HD Graphics 4000, Intel HD Graphics 4000, Built-In, 1024 MB
Memory Module: BANK 0/DIMM0, 2 GB, DDR3, 1600 MHz, 0x802C, 0x384A54463235363634485A2D3147364D3120
Memory Module: BANK 1/DIMM0, 2 GB, DDR3, 1600 MHz, 0x802C, 0x384A54463235363634485A2D3147364D3120
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0xF5), Broadcom BCM43xx 1.0 (5.106.98.100.22)
Bluetooth: Version 4.2.0f6 12982, 3 services, 15 devices, 1 incoming serial ports
Network Service: 802.11 n WLAN, Ethernet, en3
Serial ATA Device: APPLE HDD HTS547550A9E384, 500.11 GB
Serial ATA Device: HL-DT-ST DVDRW GS31N
USB Device: USB Receiver
USB Device: Hub
USB Device: FaceTime HD Camera (Built-in)
USB Device: Hub
USB Device: 802.11 n WLAN
USB Device: Hub
USB Device: IR Receiver
USB Device: BRCM20702 Hub
USB Device: Bluetooth USB Host Controller
USB Device: Apple Internal Keyboard / Trackpad
Thunderbolt Bus: MacBook Pro, Apple Inc., 25.1
could the ralink driver be interfering?
thank-you for your diligence with this
Message was edited by: julie andor gus -
HT1270 Can I replace PC3 1600 memory with PC3L 1600 memory? MacBook Pro mid 2012, i7 2.3 15"
Can I replace PC3 1600 memory with PC3L 1600 memory? MacBook Pro mid 2012, i7 2.3 15". I know PC3 memory runs on 1.5 volts, PC3L runs on 1.35 volts.
Are they compatible with my Mac?http://www.crucial.com/usa/en/memory-info < Find compatible memory
MacBook Pro (15-inch, Mid 2012) - Technical Specifications
MacBook Pro: How to remove or install memory - Apple Support -
Hello everyone,
Thank you in advanced for all of the support. This is my first post to the communities. I just bought a 2.9 GHz core 17 processor MacBook pro mid 2012 13" with 8 GB of RAM and I am in the process of upgrading it. When I bought the MacBook pro originally, I was told that I would never mac out the performance because I do not do a lot of photo/video editing. This is true, but I am an academic researcher and tend to multitask often, having 20+ safari tabs open, SPSS (a statistical program), full screen mail app, full screen calendar app, and preview, iTunes open all at the same time. I often get slow performance and error messages that state low memory. This is why I am interested in upgrading the laptop. I am getting ready to go to medical school and I want to have a powerful laptop. I also want to future proof because I plan on having a dual boot system to mac OS and windows OS.
Because I know I will be maxing out the performance of the computer, I want to take full advantage of upgrades, especially now because the cost of the components is reasonable at the moment. The following are the proposed upgrades:
1. Upgrade my current 8-GB ram (2x4-GB) with 16-GB ram (2x8-GB). I plan on using crucial RAM.
Crucial 16-GB Ram: http://www.amazon.com/dp/B008LTBJFW/ref=wl_it_dp_o_pC_nS_ttl?_encoding=UTF8&coli d=2B1KHELSPJPNN&coliid=IYGJWGQDH8LV0&psc=1
2. Replace my optical drive with a hard drive. I will place a SSD into my current hard drive position and then install my current HDD into the optical drive bay with the optibay optical drive caddy. I am doing this because I plan to use the SSD as the boot drive and my current HDD as my backup and files drive. I am putting the SDD into the HDD because I have read it is better to place it in this bay for performance. I will put the other HDD in the optical drive because the performance of that one will not be as important.
Adata SSD: http://www.amazon.com/dp/B008LTBJFW/ref=wl_it_dp_o_pC_nS_ttl?_encoding=UTF8&coli d=2B1KHELSPJPNN&coliid=IYGJWGQDH8LV0&psc=1
Optibay Optical Drive Caddy: http://www.amazon.com/dp/B0058AH2US/ref=wl_it_dp_o_pd_nS_ttl?_encoding=UTF8&coli d=2B1KHELSPJPNN&coliid=I3GI8MGWAKXY79
My questions:
1. Is the listed RAM appropriate and sufficient for my MacBook pro?
2. Is the listed SSD appropriate and sufficient for my MacBook pro?
3. Is the listed Optical Drive Caddy appropriate and sufficient for my MacBook pro?
4. Is there still a firmware problem that does not allow for SATA 3 (6Gb/s) support in the optical drive?
5. Would it be easier to format the new SSD outside of the MacBook using a SATA to USB adapter?
6. Does working on any of the listed components void my AppleCare (I plan on keeping all of the original components so I can replace them, if I ever need to see apple support)?
7. What is the best way to put Mavericks onto the SSD to make this my boot drive?
8. What is the best way to make all of my files remain on the HDD, but link to the SSD with the operating system?
9. Has anyone ever successfully upgraded to 16-GB RAM and used their optical drive for a secondary hard drive?
10. Is there any miscellaneous advice for this project?
Please feel free to give partial answers. I know this was a lot of information, but I wanted to be efficient in my post. I am very appreciative of everyone who will contribute.
Thank you!rmichaud91 wrote:
Hello everyone,
I just bought a 2.9 GHz core 17 processor MacBook pro mid 2012 13" with 8 GB of RAM
16 GB of RAM is the best you can do.
The optibay HD will null and void your warranty. -
Migration Assistant can't find External HD on MacBook Pro Mid-2012
Hi, I have a MacBook Pro Mid-2012 running OS X Mountain Lion 10.8.2 and I am trying to use Migration Assistant to transfer Time Machine backups that are on my external hard drive, that I backed up from my old MacBook Mid-2010. The problem I am having is that Migration Assistant can't find my external hard drive. My MacBook Pro can find it when I plug it in (I see it in Finder), but Migration Assistant can't. Can anyone help or should I go to the Apple Store? I need help with this problem as soon as possible.
Thanks in advance,
- Daniel Since no one replied I figured out how to do it myself.
1.) First I plugged in my external hard drive with my Time Machine backups on them, then I opened Finder and click on my external hard drive under devices.
2.) Next I clicked on and opened the folder named "Backups.backupdb"
3.) Once inside that folder I could see folders with the backups from Time Machine and all of the folders names were the date I backed up that backup. I clicked and opended the lastest backup folder.
4.) Inside that folder, I clicked and opened the folder named "Macintosh HD"
5.) Inside that folder, I clicked and opended the folder named "Users"
6.) Inside that folder, I clicked and opended the folder named "Daniel" which was my Username on my previous Mac.
7.) Finally I could see and access all my folders from my Time Machine backups from my previous Mac.
Keep in mind this is only helpful if you are trying to access old backups (backed up from another Mac) on a new or different Mac. (Sorry for the blurry images)
Hope this somehow helps someone else,
- Daniel -
I recently saw that for os x server apple says that you can run it on inexpensive hardware like mac pro, imac and mac mini. It doesn't say anything about notebooks. So if i buy os x server will i be able to run it on my macbook pro mid 2012 with i5 2.5 GH, 4 Gb RAM and 10.8.4?
Thanks.Welcome to Apple Support Communities
OS X Server is compatible with any Mac that runs OS X Mountain Lion, so you can install it on any MacBook, MacBook Pro, MacBook Air, iMac, Mac mini or Mac Pro that supports Mountain Lion > http://www.apple.com/osx/specs
Just open the App Store and purchase OS X Server. The app will appear after finishing the download, so follow its steps to set up OS X Server on your computer. You will be able to install it for free in all your computers after purchasing it. If you want more information about OS X Server, read > http://www.apple.com/osx/server/ -
The update "MacBook Pro (Mid 2012) Software Update 1.0" can't be applied
When trying to update my new Macbook Pro with Retina through Apple's software update application, I get the error:
The update "MacBook Pro (Mid 2012) Software Update 1.0" can't be applied
The update could not be expanded, and may have been corrupted during downloading.
I've already went through the process twice to download this update.Same type of error, but getting 90% downloaded and error message that the update cannot be saved. But it then goes to the screen to apply, but with 90% only - no instructions that it will only download 90% and the rest will come during the update - not going to apply.
-
hello, I am trying to reinstall os x lion in my macbook pro mid 2012, from my recovery disc, and its imposible because every time I have problems to download de installer or something that is required to do that. what can I do?
When you do get it downloaded, before you do anything else, save the Lion installer - make a copy and put it somewhere safe. you can then reuse, make a clean install and other things.
OS X Lion Install to Different Drive
How to create an OS X Lion installation disc MacFixIt
Migration Assistant Update for Mac OS X Snow Leopard
http://www.apple.com/support/lion/installrecovery/
Create an OS X Lion Install disc
http://reviews.cnet.com/8301-13727_7-20080989-263/how-to-create-an-os-x-lion-ins tallation-disc
How to clone your system:
http://macperformanceguide.com/Mac-HowToClone-backup.html
http://macperformanceguide.com/Mac-HowToClone.html
http://www.macupdate.com/app/mac/7032/carbon-copy-cloner
http://www.macperformanceguide.com/blog/2012/20120711_2-MacPro-internal-clone-ba ckup.html
Yes I strongly recommend making a clone you can boot from in addition to use TimeMachine.
Carbon Copy Cloner will also offer to copy and make a Recovery partition on the 2nd drive. -
MacBook Pro(Mid 2012) Can't connect to my Dynex TV with mini display port to VGA adapter
I have a MacBook Pro(Mid 2012, running OS X 10.9.4) and I recently just bought a mini display port to VGA adapter so I could hook it up to my dynex TV but when I connect everything my TV says no signal. Do I need to do something in settings?
Hi psikalis,
If you are having issues connecting an external display to your MacBook Pro, you may find the information and troubleshooting steps in the following articles helpful:
OS X Mavericks: Connect multiple displays to your Mac
http://support.apple.com/kb/PH13814
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/HT1573
Regards,
- Brenden -
How can connect my macbook pro mid 2012 to my imac 21.5 inch mid 2010 ?? I want to use imac like a display for macbook.
Target Display Mode: Frequently Asked Questions (FAQ)
with a mini display to mini display cable. Attach it to the Thunderbolt port on your MBP and to the mini display port on your iMac.
How do I enable TDM?
Make sure both computers are turned on and awake.
Connect a male-to-male Mini DisplayPort or ThunderBolt cable to each computer.
Press Command-F2 on the keyboard of the iMac being used as a display to enable TDM.
Note: In Keyboard System Preferences, if the checkbox is enabled for "Use all F1, F2, etc. keys as standard functions keys," the key combination changes to Command-Fn-F2. -
Where can i download the driver for my network card? i have a macbook pro mid 2012, and are using windows 7 ultimate
uhm hey guys,
idk where else to get help so ima try here,
i got windows 8 installed with bootcamp on my macbook pro late 2010 (5, 5) and theres no sound coming out of it, so i installed an nvidia audio driver (idk, it could be the incorrect one) but i have nvidia GeForce 320 on my macbook.
do you know what i should install ?
but when i go onto my osx the sound is fine, so i figured im missing something on windows 8
Orrrr could i just go out and get parallels and hope it doesn't get the same problems? -
My MacBook pro mid 2012 doesn't seem to have a "save as" function, so I can't seem to save multiple page pdf's together after moving thumbnails into the sidebar. It only saves the first page.
I do have a 2008 version of Microsoft Office installed to save money, but that shouldn't affect things. I can't figure out the "rename" function either. Help?Oh, and I also reset my NVRAM, my computer hasn't frozen again yet, so I'm not sure if it has made a difference.
Maybe you are looking for
-
Test Conditions in BPEL Fault Policy
Per the ORacle 10.1.3.3 SOA Suite techical document, under the Fault Policy Framework section you can use an XPath expression in the <test> section of a fault policy. The example provided is +<test>$fault.code/code="WSDLReadingError"</test>+ Instead
-
I have problem in repeint method please help me
my screen blinks badly when i use repaint method if i use update it only updates the page not erase prevois what i can do iam in very trouble please help me
-
Cannot install AIR 3.4 on Mac OS X 10.8.1
I have a new install of Mac OS X 10.8.1 and cannot get Adobe AIR to install. I previously could not get it to install under 10.8 either. Logs that I've found are the following: 8/30/12 4:04:47.277 PM Adobe AIR Installer[6985]: Runtime Installer begin
-
External Monitor not recognized when running XP (MDP to HDMI)
Hi, I also posted this in the "Windows Compatibility" forum. I have a new Macbook Pro (unibody, 15.4", 2.53 ghz) and I am trying to make it work with my Samsung T260HD HDTV/Monitor. I am hooking this up via a Mini displayport to HDMI adapter, Yeah! I
-
No preview image in finder window
After upgrading from Jaguar to Tiger, photo preview images from Adobe Photo Deluxe (system 9) do not appear. Instead file info is displayed. How can I fix this? This feature worked fine in Jaguar.