Can connect via ethernet cable, have good Airport signal but no connection
Hey folks,
Pesky problem. I'm trying to connect to my wireless airport extreme basestation and having problems. Everythings hooked up correctly and if I plug the ethernet cable from the modem directly to the powerbook it works fine. The odd thing is that my computer sees the base station, it has good signal, and it tells me I'm connected to the internet via airport.
Why then can I not actually acess it? Any thoughts?...it's comcast high-speed in case that matters.
Cheers,
Sean
Sean,
---- I was trying to get a link to another similar thread, where one of the experts (I'm not one of them) made some recommendations, but I can't seem to find it.
---- Is your Network Preferences selected for Airport as well as ethernet, and is Airport at the top of the list? Anyway, the fact that your direct connection PB to modem is working fine, may be the very thing causing your problem. The modem looks for the PB (MAC address?). So, you can do an hardware reset, or if not then unplug it for a good while (not tooggle the power on & off, but I think I saw someone even recommend overnight). Shutdown the AEBS & PB.
---- Then after you powerup the modem & it connects with the ISP (it takes just a short few minutes, you can watch the lights), then power up the airport, then after its connected up to the modem (again, a few minutes, you can watch the lights), bootup the PB.
---- I wish that I could have found the other thread for you, as the experts do an extremely better job of this.
-------- Gino
-
Similar Messages
-
Connect to internet via airport extreme via ethernet cable and no airport c
I just bought a MacBook with Airport Extreme, got it set up today and it works great, got online, etc. However, I have an iMac with no airport card. I can't figure out how to get both computers hooked up on the internet at the same time. The MacBook works only when the ethernet cable in in the LAN slot on the Extreme but won't work through the WAN slot. I have tried hooking up both ethernet cables into the Extreme, just the iMac, and nothing works. I don't need to connect wirelessly through the iMac so I don't want to buy an Airport card if I don't need one. I just don't want to plug and unplug the ethernet cable everytime I want to use the MacBook or the iMac. My modem from Verizon only has one ethernet slot. Any ideas?
I just bought a MacBook with Airport Extreme, got it
set up today and it works great, got online, etc.
However, I have an iMac with no airport card. I
can't figure out how to get both computers hooked up
on the internet at the same time. The MacBook works
only when the ethernet cable in in the LAN slot on
the Extreme but won't work through the WAN slot. I
have tried hooking up both ethernet cables into the
Extreme, just the iMac, and nothing works. I don't
need to connect wirelessly through the iMac so I
don't want to buy an Airport card if I don't need
one. I just don't want to plug and unplug the
ethernet cable everytime I want to use the MacBook
or the iMac. My modem from Verizon only has one
ethernet slot. Any ideas?
You mean Airport Extreme Base station?
Here's what you need to do:
1. Disconnect your Verizon Modem & Airport Extreme
2. Connect the ethernet cable from the Verizon modem to the WAN of the AE
3. Connect another ethernet cable from the LAN port of the AE to your iMac
4. Turn on Verizon Modem
5. Once all lights on the modem have turned on, turn on the Airport Extreme
6. On your iMac click on Applications --> Utilities --> Airport Admin Utility
7. Setup a Wireless network using this or the Airport Setup Assistant, located in the same Utility folder.
8. After you have created the wireless network, connect to it on your macbook
If for some strange reason you still can't figure it out, refer to the product manual or check:
http://docs.info.apple.com/article.html?artnum=106858 -
Any help is appreciated.
Make sure the ethernet cord is plugged into the WAN port on the Aiport (the port with a circle of dots above it) and do a hard reset (hold the reset button until the light blinks rapidly.) It will not automatically appear in the Airport Utiltiy. You are looking for the airport under the wifi menu after a few minutes or in Settings>Wifi on an iOS device that you can click to join and continue to setup.
-
Connecting to Airport Express via Ethernet Cable
Dear Apple Support Community,
My setup at home is such that all my devices are in such close proximity to the Airport Express, and therefore I connect everything to the Airport Express via ethernet cables (NAS, Apple TV, PS 3).
The final step in my network setup would be to connect my Macbook to the Airport Express to connect to the internet using the Ethernet Cables, instead of using the wireless connection - because my Macbook is positioned right next to the Airport Express.
However, I am struggling to get the Macbook to connect to the Internet via the Ethernet Cable through the airport express. Is there a special way to set this up if this can be done. I know Wireless would be the answer, but the problem is, when I download movies etc, I write the files directly onto the NAS which happens a lot quicker than doing so via WiFi.
I hope the above question makes sense.
Thanks in advance for any feedback.
Regards
STHello Brian Hunt1. Welcome to the Apple Discussions!
I have an old PowerBook G3 and I do not have a wireless card for it. My plan was to connect it, via Ethernet cable to my airport express which is on my home wireless network (DSL to Mac Mini to AirPort Express via built-in AirPort).
Unfortunately, the network configuration your describing, where you would use OS X's Internet Sharing feature to share the Mac Mini's wired Internet connection wirelessly with the AirPort Express Base Station (AX), won't work.
If I cannot connect my laptop this way, could anyone suggest a wireless card that is compatible with this slightly antiquated, yet very useful machine?
Only the "Pismo" PowerBook G3 is capable of using the original AirPort card. If you have this model, then the following DIY instructions will show you how to install it.
If this isn't your model, then check out the following vendor offerings:
o QuickerTek
o hField Technologies' Wi-Fire -
Connecting a Laptop to Airport Express via Ethernet Cable
I have an old PowerBook G3 and I do not have a wireless card for it. My plan was to connect it, via Ethernet cable to my airport express which is on my home wireless network (DSL to Mac Mini to AirPort Express via built-in AirPort).
My question is can I make this work? After buying the Ethernet cord, all my reading of the AirPort Express manual seems to suggest that the Ethernet port on the AirPort Express is to only be used as an input port, not as an output. Is this correct?
If I cannot connect my laptop this way, could anyone suggest a wireless card that is compatible with this slightly antiquated, yet very useful machine?Hello Brian Hunt1. Welcome to the Apple Discussions!
I have an old PowerBook G3 and I do not have a wireless card for it. My plan was to connect it, via Ethernet cable to my airport express which is on my home wireless network (DSL to Mac Mini to AirPort Express via built-in AirPort).
Unfortunately, the network configuration your describing, where you would use OS X's Internet Sharing feature to share the Mac Mini's wired Internet connection wirelessly with the AirPort Express Base Station (AX), won't work.
If I cannot connect my laptop this way, could anyone suggest a wireless card that is compatible with this slightly antiquated, yet very useful machine?
Only the "Pismo" PowerBook G3 is capable of using the original AirPort card. If you have this model, then the following DIY instructions will show you how to install it.
If this isn't your model, then check out the following vendor offerings:
o QuickerTek
o hField Technologies' Wi-Fire -
I have a 3rd party hard drive with movies on it ,it is connected to my airport extreme. The AE is connected to my tv via ethernet cable. Can I stream my movies to the Tv ?
Not without a player..
The AE is a dumb file server.. the hard disk you plug in is an even dumber hard disk.
There are no smarts in this setup.. not even DLNA. So the TV would have to be an extremely smart one to read raw files on a network drive.. none do that I know of.
A solution is WD live TV.. it can read files from just about any file source on network and play them to the TV.
Nothing apple makes will do that.. ATV is a streamer not a media player. Everything in the Apple world is tied up with itunes. So you must have a computer running itunes to use it.
You can download a more generic player for ipad, and put that as part of the network.. but you still need ATV to display the video. -
I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme. Can my network operate properly to extend the network with both a wireless and wired extend functionallity?
I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme.
Excellent plan.
Can my network operate properly to extend the network with both a wireless and wired extend functionallity?
Yes, but don't get confused about the second AirPort Extreme, as it would not be configured to "extend" a wireless network.....it would be configured to "create a wireless network" using the same wireless network name, security settings and password as the Time Capsule network. Configure the second Extreme in Bridge Mode.
This Apple support document will show you how to hookup and configure the second AirPort Extreme:
http://support.apple.com/kb/HT4260 -
Connecting aiport extreme and airport express via ethernet cable ?
Is it possible to connect an airport extreme to an airport express via ethernet cable, I ask because I want to expand the range of my wifi network to the basement of my house, the floors are really thick concrete so I installed some ethernet cable runs, I hope somebody can help me, thank you.
+How do I do it ? Do I connect the modem to the airport extreme and then run the ethernet cable from one of the extreme's ethernet ports to the express ethernet on the basememt and a second cable from another of the extreme's ethernet connectors to the express on the second floor+
Yes, this is exactly correct.
To configure each AirPort Express (AX)
Open AirPort Utility, click Manual Setup
Click the Base Station tab below the icons to name your device, assign a device password and adjust time zone settings. Give each Express a separate name so you can identify then easily.
Click the Wireless tab
Wireless Mode...Create a Wireless Network
Wireless Network Name...Exact same name as your AirPort Extreme network
Radio Mode 802.11n (802.11b/g compatible) if you want to use 2.4 GHz
Channel...Automatic
Wireless Security...Exact same setting as your AirPort Extreme network
Wireless Password....Exact same setting as your AirPort Extreme network
Click the Internet icon
Change the Connection Sharing setting at the bottom to "Off (Bridge Mode)"
Click Update at the lower right and the AirPort Express will restart in 20-30 seconds
I think it is easier to configure each AirPort Express with AirPort Utility by temporarily connecting it to your computer with a short ethernet cable. Once you have saved the configuration, you can move the Express to the location that you need.
Please post back on your progress. -
Have new Airport Extreme conneted via ethernet cable from HughesNet Gen4 modem. Using NetGear WN3500RP extender. NetGear asks for different names for the 2.4 and 5 GHz bands. Most of what I have read indicates extender should have same name as main network? How is it best to configure with the Airport Extreme router 802.11ac?
Different names for the 2.4 and 5 GHz networks are optional, but can be convenient for you to distinguish one from another. It's up to you.
-
My Apple TV will not update to the latest software, dose anyone know what the problem is, I've reset, tried to do it wirelessly as well as while connected via Ethernet cable.. Both have resulted in the same message!! Update unsuccessful, current software version is 5.1 (5201) . I've rented a movie recently and does not appear in my movie list, but I have been charged for this movie, can someone help me out with these issues.
If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
Connect the micro USB cable to the Apple TV and to your computer.
Reconnect the power cable (only for Apple TV 3)
Open iTunes.
Select your Apple TV in the Source list, and then click Restore.
If when you choose restore you get a message that the device cannot be found, download the file below
Apple TV Software Restore 5.1.1 (2nd generation)
Apple TV Software Restore 5.1.1 (3rd generation)
Then hold down the option key while choosing restore and select the downloaded file when prompted. -
I have an HP LaserJet 8150N that I use for my work and I have had this printer for ever and it is one heck of a work horse! I am trying to get it connected via ethernet cable directly to my iMac. I always had this printer connected via a network so I don't know if I am able to connect directly with a cable since it is a network printer. I have tried to reconfigure the printer using the JetDirect menu giving it a new IP address but still no luck. If anyone could help me through this issue I would appreciate it.
moonlightcaravan wrote:
Second, seeing "connecting" and connection failed is normal. You must click on "Connect As" in the Finder window and then enter the username and password for the admin account on the other computer. That should fix things.
Thanks for responding.
When does clicking on "Connect As" happen in the process above?
After step six? Seven?
After the connection has failed?
Is this the FInder window that shows the icon of the computer you want to copy the file from?
You should see "Connect As" in the Finder near the top right of the window as shown below:
!http://blog.brothersoft.com/wp-content/uploads/2008/11/howto_copy_files_to_or_from_your_iphone02.jpg! -
My A'Extreme sometimes won't connect to my MacBook Pro even if I have a green light on the device . I can unplug the ethernet cable and reconnect and it will work fine. all diagnostics say there is nothing wrong. Any ideas ?
This is more about your modem then anything. Sometimes you'll need to unplug and plug back in your modem. Consider it a glitch from the ISP or just the modem in general.
when I need to turn something off then on I try the modem first. This when I'm not doing any ware and tare to the device. -
My internet 3rd party access point in in the basement and the speakers I want to stream music to wirelessly are upstairs. Does Airport Express need to be connected to my 3rd party router via ethernet cable or will it stream music wirelessly?
Wirelessly
Just select the option to make your AirPort Express join an existing network in the setup process -
i have att u verse modem and it wi fi was not working. So i got net gear wi fi and connected to att modem . i connected my apple TV via Ethernet cable to att uverse modem . i did not want slow down my wi fi speed. My Apple phone is on Netgear wifi .Now airplay is not working .
Make sure that the Att Modem goes to the netgear router via ethernet cable. Then connect your Apple Tv with a ethernet cable to the back of the net gear router. Airplay wants it to both be connected to the same device, usually.
-
Cannot configure Airport Express via ethernet cable
I am trying to configure my new Airport Express, in order to stream music to it.
I have a wireless switch/router (Linksys), but DHCP is disabled.
My mac has no wireless card, it is connected via cable, on 100Mbps port.
A friend advised me to connect the AE directly via Ethernet cable, in order to first configure it.
I connected the AE to the router, and the Mac (in the Airport Setup wizard) tells me that "No airport card is installed" (correct). I then click on "Continue", and I can choose between "Configure a new Airport station" and "Modify...".
If I select "Configure...". I get the following message (I am translating from french): The Wizard detected a new Airport Express called "Base Station 5f6281". Good!
But If I click "Continue", it will report "An orror occured when contacting the selected Airport station".
What should I do?
If, instead of selecting "Configure..", I try to "Modify an existing configuration", I have the same when I then click on "identify". What is the trick?
Thanks for your help
RobinFollow the instructions posted here by David Lovell (which work equally well for Macs and PCs):
David Lovell, "Airtunes for XP with a Wired/Wireless network" #1, 09:05pm Jan 8, 2005 CDT
Notes:
1. You MUST re-enable DHCP on your router. If you don't, the Airport Express won't be able to get an IP address. If your Airport Express doesn't get an IP address, your Mac won't be able to communicate with it.
2. When configuring via an ethernet connection, you must use the Airport Admin Utility (David's article tells you this as well). The Airport Setup Assistant can only be used if you are going to do the configuration wirelessly from an Airport card equipped Mac.
Maybe you are looking for
-
While processing a message : Error HTTP 404: not found
Hi gurus, I'm stuck on a File-XI-IDoc scenario. Here is the message i get in the Message Tool Display: Erreur lors de la transmission du message au point d'accès http://rchase12:53000/sap/xi/engine?type=entry via la connexion File_http://sap.com/xi/X
-
Rx2 or rex files in media browser at 96khz and up
help please.... I am a techno / deep house producer and been working with logic for quite a while albeit mostly with external/internal samplers.Recently I switched to more loop oriented workflow and using the media browser to preview and import loops
-
Wi-Fi on/off on my iPhone 4S is grey. First 2 times I switched off then on it was fine. Third time this didn't work so I have done a full restore of the software and network settings and followed everything in Apple Support but still grey - nothing e
-
Want to disply posted document in BDC
Hi Frnds, In my BDC i want to display the document no that was posted successfully, i m using statment as follows, CALL TRANSACTION 'MB1B' USING bdcdata MODE 'A' UPDATE 'S' MESSAGES INTO messtab. APPEND messtab. But messtab does not conatin any recor
-
WebSAPConsole - Issue latest patch
After patching SAPLogon at the webserver with the latest patch (of 02/05/2005) a lot of trouble was resolved! But now we got another 'problem': if people are clicking very fast at a button, sometimes the destination screen is displayed twice or the u