Can HWIC-1CE1T1-PRI support voice applications

The product sheet and another helpful forum post clearly states that the HWIC-1CE1T1-PRI does NOT support voice applications on the PRI, only data applications. However, running 15.2(1)T when we configure a PRI group, it seems to imply that it can support a voice application with a command option to the PRI-group.
dal-rtr02(config-controller)#pri-group timeslots 1-24
%PRI-group is created for data application only.
%For voice application, please remove this pri-group, then configure pri-group again with voice-dsp option.
What gives? I cannot find this command documented anywhere. What does the "voice-dsp" option for the "pri-group timeslots" do?
Should we assume this card can STILL not be used for SIP/TDM Voice gateway services?
Thanks for any tips/confirmation you can provide.
Kris

Understood, but what is this "voice-dsp" option for on the end of the "pri-group timeslots" command?
This seems undocumented.
The router output is confusing and implies you could use the "voice-dsp" option to enable voice application. What is this all about? Best ignored I guess. The customer is now buying the correct hardware.

Similar Messages

  • PVDM2-12DM compatibility with HWIC-1CE1T1-PRI

                      Hi there,
    I'm hoping someone can assist.  The setup i am trying to get working is the following
    User dials in over POTS to an ISDN30 Line.  The ISDN30 line (3rd Party Supplier) is connected to our 2911 via a HWIC-1CE1T1-PRI module.  We have inserted a PVDM2-12DM into the router to handle the POTS call.
    Problem we have is that we cannot seem to get a modem tone when the user dials in.  The ISDN line connects and the debug modem command shows the modem SETUP & INIT phase - see below
    Aug 13 12:58:52.341: CSM: MODEM_REPORT from 0/0/0:0, call_id=0x61, event=0x1, cause=0x0, dchan_idb=0x2B2C837C
    Aug 13 12:58:52.341: CSM: called_number 'number removed' modem_pool 2AA6CE14 deny_call FALSE
    Aug 13 12:58:52.341: CSM: Next free modem = 0/202; statbits = 10020
    Aug 13 12:58:52.341: Modem 0/202 CSM: modem is allocated, modems free=-1
    Aug 13 12:58:52.341: Modem 0/202 CSM: Incoming call from Unknown to 'number removed', id 0x61
    Aug 13 12:58:52.341: Modem 0/202 CSM: (CSM_PROC_IDLE)<--ISDN_CALL
    Aug 13 12:58:52.453: CSM: MODEM_REPORT from 0/0/0:0, call_id=0x61, event=0x4, cause=0x0, dchan_idb=0x2B2C837C
    Aug 13 12:58:52.453: Modem 0/202 CSM: MODEM_REPORT rcvd DEV_CONNECTED for call_id 0x61
    Aug 13 12:58:52.453: Modem 0/202 CSM: (CSM_PROC_MODEM_RESERVED)<--ISDN_CONNECTED
    Aug 13 12:58:52.453: Modem 0/202 CSMV12: SETUP(Answer) ISDN 0/0:0
    Aug 13 12:58:52.453: Modem 0/202 CSMV12: configured for Answer(A-law) mode, with Null signaling, 0x0 tone detection
    Aug 13 12:58:52.453: Modem 0/202 CSMV12: INIT(Answer) ISDN 0/0:0
    Aug 13 12:58:52.453: %ISDN-6-CONNECT: Interface Serial0/0/0:0 is now connected to N/A N/A
    Aug 13 12:58:52.485: CSM: csm_modem_event called
    Aug 13 12:58:52.485: Modem 0/202 CSM: (CSM_PROC_WAIT_FOR_CARRIER)<--CSM_EVENT_MODEM_SETUP Aug 13 12:58:52.341: CSM:
    but there is no modem tone or any more output from the debug commands.
    The ISDN line is working fine as a normal ISDN dial in is successful.
    Has any one tried this before or is there a known issue with this solution?

    Updated the IOS but made no difference.  Turns out i was missing the line 'network-clock-participate wic 0'  Added this to the config and managed to get incoming POTS calls.  Only problem now is that the PITS call won't stay up for more than 5 seconds.  Looking at the Modem AT registry settings.

  • So I've been trying to open some Microsoft Word Documents and it says it can't be opened because PowerPC applications are no longer supported. What do I do about this?

    So I've been trying to open some Microsoft Word Documents and it says it can't be opened because PowerPC applications are no longer supported. What do I do about this?

    Workarounds:
    1.  Restore the OS X that you formerly used to run Word 2004;
    2.  Partition your hard drive or attach an external hard drive and install Snow Leopard (and Rosetta) so that you can "dual-boot" into Microsoft Word 2004;
    3.  Upgrade to Word 2011 or use an alternative program; or
    4.  The solution I use: Install Snow Leopard (and Rosetta) into Parallels 7 or 8:
                                  [click on image to enlarge]
    Full Snow Leopard installation instructions here:
    http://forums.macrumors.com/showthread.php?t=1365439

  • I can't install my old logic 8 on my new macbook pro. It says it does not support powerpc applications anymore. what do i need to do?? this is ridiculous!!!

    I can't install my old logic 8 on my new macbook pro. It says it does not support powerpc applications anymore. what do i need to do?? this is ridiculous!!!

    Logic 8 will probably run on your new machine but the installation program contains some older PPC code for pre Intel Macs. This was not a problem as all OSX versions contained the "Rosetta" PPC emulation, that is, up until Lion when all PPC emulation was dropped.
    There are ways to do this however, try searching Google for:  Installing Logic 8 under Lion or Mountain Lion.

  • Diablo II can't open b/c PowerPC applications are no longer supported.

    Downloaded OSLion and now Diablo II can't open b/c PowerPC applications are no longer supported.

    Correct. Lion does not support Rosetta, hence, no PPC applications. You need to install Snow Leopard in order to run a PPC application or have the application upgraded to a compatible version.

  • I downloaded Mountain Lion and now my quicken data is gone as it says it now longer supports pc applications what can I do?

    I downloaded Mountain Lion and now my quicken data is gone as it says it now longer supports pc applications what can I do?

    Install this version.
    (70052)

  • Says no supported calendar application can be found in my itunes page

    have installed the latest itunes...sync's properly with everything except calendar....says no supported calendar application can be found on my pc..running windows xp...any suggestion as to how I can view and sync calendar on my pc??

    With XP and Vista, the only application supported for syncing calendar events is Outlook 2003 or 2007.
    Do you have Outlook 2003 or 2007 installed on your PC?

  • Pls help!Can Oracle v7 support WebSphere Application Server instead of Oracle 8i

    Hi,
    I am using WebSphere as my application server and NT4.0 as OS.
    I wish to connect to Oracle db which is located at another server.
    Currently what I have is Oracle Client Software v7.3.4. There is error when I want to start the service.
    So I suspect that it is not compatible and it might require Oracle 8i in web environmt and to support WebSphere Application Server as well.
    Can anybody help me? Thank you.

    Hello,
    I guess you could get that to work as somebody was able to use WebLogic as webserver: http://christopherbeck.wordpress.com/2008/09/15/weblogic-server-and-apex/
    Alternatively you could use the Embedded PLSQL Gateway if you don't want to install Apache (depending database version you are on).
    Regards,
    Dimitri
    http://dgielis.blogspot.com/
    http://www.apex-evangelists.com/
    http://www.apexblogs.info/

  • IOS6 doesnot support Map Application fully in India. I have updated my i phone4 to ios 6. Now I feel that Map application was much better in ios5. Can I retract only this application?

    iOS6 doesnot support Map Application fully in India. I have updated my i phone4 to ios 6. Now I feel that Map application was much better in ios5. Can I retract only this application?

    I don't know if this helps, but I'm still working on this problem and took a screen shot of my Console Message errors:
    What's happening here is opening the program, trying to save and it crashes. Then trying to open the program again and it crashing before it even opens.  Finally opening the program a third time and trying to save it using "save as" instead of "save" (which I found one forum recommending) and it crashing again. 

  • Difference between NM-1CE1T1-PRI and NM-HDV2-1T1/E1

    please if any one can give me the difference between NM-1CE1T1-PRI and NM-HDV2-1T1/E1

    Hi Ahmad,
    NM-1CE1T1-PRI does *not* support voice. Please refer to the following urls:
    Cisco E1/T1 ISDN PRI Network Module - Data Sheet
    http://www.cisco.com/en/US/products/hw/modules/ps2797/products_data_sheet09186a0080189f95.html
    Voice Hardware Compatibility Matrix (Cisco 17/26/28/36/37/38xx, VG200, Catalyst 4500/4000, Catalyst 6xxx)
    http://www.cisco.com/en/US/products/hw/routers/ps259/products_tech_note09186a00800e73f6.shtml
    Relevant Interfaces and Modules
    http://www.cisco.com/en/US/products/ps5855/products_relevant_interfaces_and_modules.html
    -Vaibhav

  • Voice Application Deployment Error

    Hi All,
    I created a Voice Application which R3 as back end. The Application was working fine. It was accepting Account Number as Input and gives Balance as the output. Now When i deploy the application, it gives me
    Error:- "Problem Resolving the dependencies.Detailed Error was. There is more than 1 main Voice Application in the list to be compiled components. This is currently not supported.".
    I have checked all the services in Visual Admin. All Services are working fine. Also I gave the runtime as "Voice". (both default runtime and RFC configure "runtime").
    Where could be the Error? Can anyone please help me out regarding this issue?
    Thanx and Regards,
    Divya

    Resolved the Problem By Myself..

  • Error message when installing iTunes on my PC:  This installation package could not be opened. Verify that the package exists and that you can access it, or contact the application vendor to verify that  this is a valid Windows installer package

    Error message when trying to install iTunes on my Pc:
    Using Windows 7, had to replace hard drive.  HELP!!
    This installation package could not be
    opened. Verify that the package exists
    and that you can access it, or contact
    the application vendor to verify that
    this is a valid Windows installer package

    Hello JAH1961,
    I recommend following the steps in the article below when getting an error message trying to install iTunes:
    Trouble installing iTunes or QuickTime for Windows
    http://support.apple.com/kb/HT1926
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • I am trying to download iTunes to my Sony PC,  but "This installation package could not be opened.  Verify that the package exists and that you can access it, or contact the application vendor to verify that this is a valid Windows Installer Package."

    mI am trying to download iTunes to my Sony PC, but I keep getting the following error after initial download attempt:
    "This installation package could not be opened.  Verify that the package exists and that you can access it, or contact the application vendor to verify that this is a valid Windows Installer Package."
    I have Windows 7 Home Premium, Service Pack 1.
    Any help is greatly appreciated.

    Hi gump68,
    Thanks for visiting Apple Support Communities.
    You may find the steps in this article helpful if iTunes is not installing on your PC:
    Issues installing iTunes or QuickTime for Windows
    http://support.apple.com/kb/HT1926
    All the best,
    Jeremy

  • When i try to install iTunes onto my new computer, it says ""installation pkg could not be opened.  Verify that this pkg exists and that you can access it, or contact the application vendor to verify that this is a valid Windows Installer pkg."

    When I try to install iTunes onto my new computer, it says "This installation package could not be opened.  Verify that this package exists and that you can access it or contact the application vendor to verify to verify that this is a valid Windows Installer package."  I can save iTunes onto my computer, but when I click run, this is the message that appears.  How do I get this thing installed?

    Hello annesmith1954,
    Thank you for using Apple Support Communities. 
    You can use the information in the following article to troubleshoot your installation issues with installing iTunes on your PC. 
    "Could not open key" message when installing iTunes or Apple components for Windows
    Regards,
    Jeff D. 

  • No supported calendar application in iTunes for iPod Touch

    Hello everyone,
    Right now I'm having trouble syncing my calendar on my iPod touch. I'm using iTunes 7.4.3 and I have Outlook 2003 installed on my computer, but iTunes says "No supported calendar application can be found." in the Calendar section on the info tab. I've tried restoring my Touch several times, in addition to removing / reinstalling iTunes and Apple Mobile Device Support several times, and now I'm at a loss.
    The weird thing is, I had a 1st gen nano hooked up to this computer as well, and for that iPod, iTunes could detect Outlook just fine. I have no idea why this is happening with my iPod Touch. Any help?

    I am facing your problem too. My iTunes seems do not recognize my Outlook 2002 SP3. I am using Traditional Chinese Edition on WinXP SP2 T.Chinese platform. Is it the cause of this problem? Hope that anyone can help us.

Maybe you are looking for

  • Unable to extend table space

    Hi, I am unable to extend the tablespace in oracle, and also all DBA jobs are failing like CHECKDB AND UPDATE STATISTICS. When i run BRTOOLS with ora<SID> user on unix, it gives the below error. " BR1049W Not enough free space in /oracle/DEV/sapdata/

  • I have two queries do do with Mail  running 10.9

    1     ICloud seems to have lost a great many of my sent messages.  I have a few recent ones and then some from 2012 and a few others going back to 2010. I rely on the iCloud sent mesages to know what I have said to people.  Are they lost forwever or

  • Requisition Creation Process from MSS in E-Recruiting-EHP4

    Hi I have the client requirement, that any of his managers should be able to create the  requisition and submit it. It should go to the Recruiter and then assigned Recruiter should be able to do the job posting etc. Once the candidates applied to tho

  • I have an iphone 3GS i upgraded to the latest ios and now i cant go past the activation screen

    i tried everything on the iphone and  on itunes..i called.apple and they want 19 dollars for a problem they have created...i miss steve jobs he wouldve helped i tried everything..plz help

  • Can I buy a warranty

    If I've had my macbook pro for one year and the warranty has now expired that came with the macbook pro can I buy apple care now?