Can i add a solid state drive to my late 2006 macbook

Got a dumb amateur question. I have a 120g hard drive in my late 2006 macbook and two 2 one gig memory cards upgraded from apple when purchased. Can i upgrade to a SSD and more memory on this mac? Can it be done on a amateur level. Is it worth it?

You should be able to upgrade the memory to as much as 3GB by installing
one 2-GB RAM, and one 1-GB RAM for that grand total combined amount.
If your computer is really a MacBook Pro model, the numbers will vary.
This is a little bit more than the 2GB total officially recognized; some users
had installed two 2-GB RAM chips, but seldom evidence the extra 1GB.
•MacBook: How to remove or install memory - Apple Support
A place to check on slower style SSD upgrade parts for older Macs may be
OWC macsales.com, as they have some that are about the data rate of
the older early MacBook computers. Faster ones would be a waste, though
some are backward compatible to slow computer data transfer rates.
Also check the OWC for memory. They have RAM based on the correct identify
of the computer in question and have a good reputation among Apple users.
There are instructions in their site (free/video) on how to install an SSD. To use
an external HD enclosure is a suggested method to get the SSD ready, prior to
attempt to install; then it can be less troublesome. Back up your original HDD
and system content. If desired, you may be able to use a clone or disk image.
The iFixit.com repair guides (specific to various models) can be a helpful way
to look into steps on how to replace and upgrade Mac computers. They're free.
{There were no replies here when I started... or I wouldn't have bothered}
Good luck & happy computing!

Similar Messages

  • Inspiron 20 3000 can I add a solid state drive to boot for speed ?

    I'm looking to purchase an inspiron 20 3000. I asked sales if I could get it configured with an SSD drive, and they said no. I'd have to purchase it and then the drive myself. But on Dell's web site I don't see any SSD drives, or hybrids listed as compatible. 
    Anybody know if this is possible ?
    Thanks,
    Ed 

    Hi ekratz,
    The system uses normal 2.5 inch mechanical hard drive with hard drive bracket (hard drive case) as the system can be used for SATA III technology hard drives the system should accept SSD drive but Dell has not tested this system with SSD.

  • I would like to add a solid state drive to my 27" iMac i7 (Jul 2010). Can this be done?

    Good day all
    I would like to add a solid state drive to my imac 27" which currently has 1TB drive.  I know that you can by the imac with a ssd and an hdd but can a dealer install a ssd after the fact?

    I did there are no videos for installing a HD in a late model iMac on OWC's website that I could find. Once again, can you provide the URL on OWC's website that shows instructions on how to install?
    Also it will NOT be the same process because SSD's are 2.5" devices and the internal HD's in a iMac are 3.5" devices. Therefore either an adapter or some type of bracket must be used. Apple does NOT include the bracket on non-SSD equiped iMacs so it's up to the shop or user to source one.

  • Can I use a solid state drive (SSD) with a G4 1 GHz powerbook? If so, how do I do it?

    Hi:
    Can I use a solid state drive (SSD) with a G4 1 GHz powerbook? If so, how do I do it? Thanks.
    fromx001

    fromx001 I believe you can use a SSD as internal drive, of course make sure to buy an ide/ata. There are all sorts of sizes up to 480 GB also in the ide/ata standard. You should however research carefully your purchase, as the performances of your SSD are going to have to rely on firmware "garbage collection", as the older operating systems haven't been written with SSD in mind.
    Mac Man JW: some people depend on Classic as a brody said, other people need a phone modem from time to time, other people use the laptop in harsh environments, and at -15C and below, LCD screens easily crack and break; NOT the powerbook which has hot air towards the screen (and it's a machine that heats quite a lot). My alu Powerbook 12", which was *not* treated with velvet gloves, only once had a cracked screen: a cleaning lady had stepped over it (!!!!) no joke. And in normal / light use today, it is still pretty decent and usable. 

  • Can I use a Solid state drive in my 21 inch iMac

    Can I use a Solid state drive in my 21 inch iMac if so what manufaturer is recommended?

    Yes. I have used and recommend OWC's Mercury models and OCZ's Vertex 3 models. They do work in Macs. Depending upon the model you have you should get either 3 Gb/s or 6 Gb/s drive. That will depend upon your computer's disk drive bus support - SATA II or SATA III, respectively.

  • What SSD (Solid State Drives) will work with a MacBook Pro unibody  A1278

    What SSD (Solid State Drives) will work with a MacBook Pro unibody  A1278?
    I see all these options and I would like to know proper dimensions and speed:
    SATA III (6 Gbit/s)
    SATA II (3 Gbit/s)
    SATA (1.5 Gbit/s)
    PATA (IDE)
    mSATA
    PCI Express
    Thanks!

    Thanks! It looks like Sata III is the way to go and most are happy with this one:
    Samsung 840 EVO
    http://www.amazon.com/Samsung-Electronics-2-5-Inch-Internal-MZ-7TE250BW/dp/B00E3 W1726/ref=sr_1_1?s=pc&ie=UTF8&qid=1396894663&sr=1-1&keywords=ssd+2.5

  • I replaced my hard drive on my late 2006 Macbook Pro.  I tried to do a reinstall of Tiger 10.4.5 from my start up disk.  I get an error that states "can't install on this computer." HELP

    I replaced my hard drive on my late 2006 Macbook Pro.  I used the disk utility and erased the drive and formatted it to OSX Journaled .  When I tried to install the OS from the start up disks I got the error "Can't install on this computer.  I have verified the drive.
    I have used Super Duper to copy my old drive to my new drive.  But I wanted to do a fresh install.  How do I go about this? 

    Did you do the Super Duper clone before you tried to reinstall the OS? If so, the original install disc is likely earlier than 10.4.11, and that may be why you are getting the message.
    When trying to reinstall the OS, did you select the "Archive and Install" option? If not, you might try that. Here's a link that might help:
    http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh1103.html
    Good luck!

  • Can I install a solid state drive in my CQ62-215DX

    I need to replace my hard drive in my laptop and I'm curious first on whether or not I can install a solid state drive in this laptop and if so, are there any recommendations?

    Hi,
    Yes you can, SSD's are much cheaper now. You can buy from the following reliable vendor, it guaranties its products will work:
        http://www.crucial.com/upgrade/HP+-+Compaq-memory/​Presario+CQ62+Series/Presario+CQ62-215DX-upgrades.​...
    You can buy from 120Gb to 960Gb. I bought one Crucial 960Gb last week but from Amazon
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Can I upgrade the solid-state drive in a MacBook Pro with retina display after purchase?

    There used to be an option to upgrade the solid-state drive when configuring a MacBook Pro on the Apple Store online, but it is now gone.  This makes me wonder if Apple's SSDs are built into the computer like the RAM is.  So, is it possible to upgrade the SSD later?  I don't want to pay so much more to upgrade everything else, so I'd love it if it's possible to just upgrade the SSD later.  Thanks!

    You will void the warranty. Here are the available post purchase upgrades. http://eshop.macsales.com/shop/SSD/OWC/Air-Retina/Apple-MacBook-Pro-Retina-2012- Drive-Internal-Flash
    You should order it with as much storage as you can afford rather than doing a post purchase upgrade because of the warranty being voided.
    Message was edited by: BobTheFisherman  Sorry. I just noticed I posted the link to a 2012 retina flash upgrade.
    Here you go http://eshop.macsales.com/item/Other%20World%20Computing/SSDAP12R480/
    Read the specs carefully to ensure this will work for the model Macbook Pro you are getting.

  • Can i put a solid state drive in my hdx16

    Has anyone tried to put a solid state drive in a HP HDX16 and, if so, what problems, if any, did you encounter?  Thanks.

    Hi,
    Like any laptop, you can replace existing HDD with a SSD. Please check the following guide:
       http://www.pcworld.com/article/192930/how_to_upgrade_your_laptop_hard_drive_to_an_ssd.html
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Add a solid state drive

    Hello Anyone
    I have been targetted as one of the macs which needs to have its HDD replaced due to a possible fault. While I have to re-install all my software again etc etc, I was considering adding a solid state drive to the internals and insall the OS on there instead of the spinning disk.
    Can anyone advice me if I can do this with my model? I read that some models allow it, but others don't.
    My model is the 27-inch, Late 2009
    Any help would be great.
    Thanks in advance
    Al

    any ssd will work, the mac you have is running on SATA II so unless you have a possible future use for the SSD after you scrap your mac there is really no reason to go with an expensive SSD. Also, a 7200 RPM seagate barracuda will give you 180mb/s on sequential.
    if you want a high performance SSD get either a Samsung 840 Pro or a OCZ Vertex 4.
    if you want to save money and still get a ssd get an Adata SX900 or a OCZ Agility 4.
    OWC uses a box standard Sandforce II controller (same as the Adata) but is overpriced, and they dont work any better with a mac.
    for instructions to replacing your hard drive:
    http://www.ifixit.com/Guide/iMac+Intel+27-Inch+EMC+2390+Hard+Drive+Replacement/8 919/1

  • Can I install a Solid State Drive (SSD) on a P6510f

    I have a HP p6510f computer.  I need to know if I can purchase a 120 gig SSD drive and use it as my PRIMARY drive and use the 750 gig as a slave.  I've read a few links about changing the BIOS setting but have not seen a solution.
    I do not want to go out and buy one if it does not work.  I currently have 16 gigs of ram and upgrade the 250 watt power supply to a 500 watt power supply.
    I want to do some video editing (already changed the video card to an ATI 6850).
    What is the best way to speed up my hard drive for video editing?

    Hi:
    You should be able to, as long as you get one that comes with an 3.5" adapter to connect to the drive bay.
    Below is the link to the service manual. It appears that there are two drive bays in the cage.  Just ensure you have another SATA power lead.
    http://h10032.www1.hp.com/ctg/Manual/c01859455.pdf
    As far as configuring, check to see that the storage controller can be set to AHCI.
    If it can't, then set it to RAID.
    I have no idea what port you connect the 750 GB drive to, looking at the motherboard diagram.  Look at the port that the boot drive is currently connected to and it should be labeled on the motherboard. Normally SATA 0.  You will want to connect the secondary drive to the SATA port with the next corresponding number such as SATA 1.
    You will not be able to use recovery disks to install W7 as a 120 GB drive is much smaller than the drive that you are using now, so you will need to install W7 using this method:
    Copy the SWSetup folder from your C:\ drive to a portable storage device.
    That contains all of the program and driver installation files that came with your PC, and you can explore the sub-folders and reinstall whatever programs you want. All should be there except office 2010 starter.
    If you can read the 25 character Microsoft windows 7 product key, you can download plain Windows 7 ISO files to burn to a DVD for the version of windows that came installed on your PC, and that is listed on the Microsoft COA sticker on your PC's case.
    Burn the ISO using the Burn ISO option on your DVD burning program and burn at the slowest possible speed your program will allow. This will create a bootable DVD.
    Or use the Windows 7 USB/DVD installation tool to compile the ISO file you download from Digital River. Link and instructions below. You need a 4 GB flash drive to use the USB method of compilation.
    http://www.microsoftstore.com/store/msstore/html/p​bPage.Help_Win7_usbdvd_dwnTool
    Use the 25 character product key on the PC to activate the installation.
    The key will activate either a 32 or 64 bit installation.
    Then go to the PC's support and driver page to install the drivers you need.
    Link to the W7 ISO file downloads is below.
    http://www.mydigitallife.info/official-windows-7-s​p1-iso-from-digital-river/
    Paul

  • Can I add a Solid State Hard Drive to a iMac 27' 2.7 if it did not already come with one?

    I am thing about purchasing a brand new Imac 27" 2.7. I do not want to spend the money now to have Apple add one at time of build but may want to add one down the road...is this possible? Can I bring it back to Apple after the fact and have a SSD added???? Please help as this will affect my purchase decsion.

    Apple will not do it for you however you may find AASP's that will. However remember these are not intended to  be upgraded as you are suggesting. First aftermarket SSD's will not work correctly and may overheat the machine, next this may would void the warranty. I would recommend reading the warranty. There are those that will argue with me on this point however I like to error on the side or caution. If the warranty is of no value to you and you just want to save a few bucks you can ask a AASP to do it.
    Another avenue to take and the one I'd recommend is buying a refurbished machine from Apple, they come with the same warranty as a new machine and some do have SSDs.  You don't state where you are from but look at the online store for your country and you should find a section for iMac refurbs. There are many advantages to buying refurbs including saving money, getting a machine more thoroughly tested than new, warranty coverage and eligibility for AppleCare. In addition most people cannot tell a refurb from a new machine, the only difference to most is the box it ships in. One has colorful graphics the other is the same box and packaging sans graphics.  The only downside I can really think of is you may not get the exact configuration you want. Most machines I've seen only have the SSD in them, I haven't seen any with SSD and HD in the refurb section. Not a big deal, just buy FW800 or Thunderbolt EHD and you have a nice solution. Others assume the machine was refurbished because it was flawed in some fashion, that isn't necessarily the case and if it was it was fixed and retested. Machines enter the refurb program for a variety of reasons, last years model, wife makes a husband return an expensive toy, changed his mind and bought a MacBook Pro instead etc.....
    If you really want a new one with an SSD I'd just save a few more bucks and get what you want.

  • Can I use a Solid State Drive (SSD) as a startup disk

    My System Drive just crashed. So I need a new unit. I would like to get away from a mechanical unit so I was thinking that a SSD would be nice.
    Will my Powermac G4 (867 mhz) running Mac OS 9.2.2 let me install and run the SSD as a startup drive?
    Gary

    I have never used a SSD but I do have G4s with SATA cards - they work well but do not support booting.
    My advice is to ensure that you buy a SSD which will work in your G4 and allow booting. This will probably involve an IDE or SATA SSD controller specified as allowing booting.

  • Can i add a second hard drive to my late 2011 mac book pro 15.4

    I have the 750 GB HD and am getting down to 300Gb I would like to ad the 750 hybrid to my mac book pro. But didn't  know if there was a place to mount it because I havent taken it apart.

    You'd have to remove the Superdrive...will void your warranty...and use something like this:
    http://eshop.macsales.com/item/OWC/DDAMBS0GB/
    If you have any problems, you will have to reverse it all before you go to a genius bar. Many users do this with no issues.

Maybe you are looking for

  • HT203175 my itunes no longer can connect to the apple store on 1 of my xp computors

    1 of my computors has stopped allowing itunes the ability to connect to the apple store

  • Search not working in WebHelp

    I have a project containing hundreds of table definitions, for each I have created a separate topic. For example one such table is FR_STAN_RAW_BOOK and I have created a topic of the same name. The topic is in the TOC and indexed but when I try and se

  • End user permission ignored

    Hello, I have a problem with an end user permission that seems to get ignored: I wanted to demonstrate the usage of the end user permission and assigned a role to a User (for simplicity's sake as an entry point, no worksets, pages etc. involved) and

  • Any solutions for MW1 (not so)Smart Wireless Headset Pro errors?

    These are the problems I have experienced so far and have not had any feedback from Sony as to how to fix them. Anyone got any suggestions apart from demanding a refund? *This device doesn't work at all as an MP3 player as it is advertised to do. Add

  • ChooseFromListUID is always -1 in find mode

    Hi, Can I create ChooseFromList in a system form that is opened in FIND mode? I want to know if there is a way to do it because every time I create ChooseFromList in FIND mode the ChooseFromListUID always has value -1, instead of UID that I gave. Tha