Can I share a USB drive connected to Airport Express

I know that you can with the Extreme Base Station. Just curious if a drive connected to the
Express would show up as a shared network drive

pgoodwin wrote:
Just curious if a drive connected to the Express would show up as a shared network drive
no.
airport express does not support connecting external drives to it. essentially, it's printers only.

Similar Messages

  • Can Time Machine backup USB Drive connected to Airport Extreme Base Station

    I need a new N based wireless router. I would prefer to get just the $179 Base Station and not the $299 Time Capsule. I already have a nice external USB 500GB drive that I would connect to the AEBS. So, once I have this new wireless router/base station installed at home and I have the external USB drive connected to it, can my new Macbook Air with a USB connected 400GB drive be used to backup what is on the Macbook Air and also backup the 500GB USB drive info that is connected to the extreme base station?
    Thanks
    tj

    I found this when searching Apple's web site but it is old, October 2007, and said it could not be done. Has this changed since then?
    Here is what I found.
    Mac OS X 10.5: Time Machine doesn't back up to AirPort Disks
    * Last Modified on: October 26, 2007
    * Article: 306833
    Time Machine in Mac OS X 10.5 Leopard can be used to back up to many kinds of Mac OS Extended-formatted drives, but it does not support AirPort Extreme's AirPort Disk feature.
    Time Machine can back up to another Mac running Leopard with Personal File Sharing, or to a Leopard Server volume, or an Xsan storage device.

  • How to share external USB drive connected to airport time capsule

    I have a 4TB Seagate USB Hard Drive connected to my Airport Time Capsule.  The Time Capsule connected to a newer iMac running Maverick.
    I use the Time Capsule for Time Machines Backups and as a Router, as it was designed for.
    I want to use the external Seagate drive to share content with other devices (Mac, IOS, Windows) on my home network
    Problem:  I cannot figure out how to SHARE the external Seagate drive so that any other devices can see it.
    Steps tried:  Go to System Preferences, Sharing, and I am unable to add this Seagate drive to list of sharable objects.  It is grayed out.

    the drive is formatted as AppleShare. Is that a potential problem?
    No, that is the correct setting if you want to share out the drive.
    Finally, when I run Disk Utility I don't see the Seagate drive (nor the Time Capsule) at all.
    Remember that the Time Capsule is a network drive. Any other drive connected to the USB port on the Time Capsule is also a network drive.
    Disk Utility cannot be used on a network drive.  It only works on a drive that is directly attached to a Mac.  If you need to partition the USB drive or something similar, you will need to connect it directly to your Mac for the operation.
    Otherwise, everything looks correct in AirPort Utility.

  • Time machine can no longer see USB drive connected to airport extreme

    According to what I read, as of March, a year ago March, with update 7.3.1 Time Machine will see the USB hard drive connected to the Airport Extreme. This was working fine. It no longer does. I had the latest airport extreme software and firmware updates. I tried going back to 7.3.1.
    Does any one have any idea how to make Time Machine work again when connected to my airport extreme?

    bradleydad wrote:
    According to what I read, as of March, a year ago March, with update 7.3.1 Time Machine will see the USB hard drive connected to the Airport Extreme. This was working fine. It no longer does. I had the latest airport extreme software and firmware updates. I tried going back to 7.3.1.
    Does any one have any idea how to make Time Machine work again when connected to my airport extreme?
    what exactly do you mean when you say that TM doesn't see the drive? do you mean you can not choose it as the destination TM drive in TM system preferences? do you see the airport drive mounted in finder? if yes, connect it directly to your mac and repair the disk (not permissions) with disk utility. then move it back to AEBS. see if that helps. if not try the following terminal command
    defaults write com.apple.systempreferences TMShowUnsupportedNetworkVolumes 1
    it should not be necessary with drives connected to AEBS but it might work.

  • Can't access a USB Drive connected to Time Capsule from a Windows PC.  Apple Care can't/won't assist.  HELP!!!

    Trying to get my Windows 7 PC to access the USB Drive that is connected to my Time Capsule.  I have a Fat32 Formatted USB drive connected to a 2TB Time Capsule and I'm trying to get access to that drive from a Windows 7 PC.  I've attempted to map the network drive (based on some 3-4 year old articles I could find online) but any time I access a file from the PC, the Time Capsule "freaks out" and disconnects all connections to it which forces me to unplug it to restart the Tim Capsule.  I'm at a loss now as to what to do.
    Spent a few hours talking to Apple about this and much more.  Apple Care can't or won't help with this particular problem (the guy I talked to, as nice and helpful as he wanted to be, had no experience supporting their hardware in a Windows environment).
    Someone has to know how to fix this so, PLEASE, help if you can!

    First off, Archon23, what you want to achieve is possible.  I have access to both my Time Capsule (TC) and the USB drive connected to it, from a Win. 7 and Win. XP machine.
    Here is what I see from the Windows side of things:
         From My Computer - TC USB Drive (Y)
         From Windows HomeNet - Time Capsule:
    Now getting there is the trick.
    One caveat before proceeding:  I am not well versed in Windows Networks, Windows Sharing and Firewall settings so some of the following may not be elegant, may not be absolutely required, and may not be the best way of getting there.  But it is what I did to see both the TC drive and it's attached USB  drive on the Windows side of my network..
    1.) First, I added Airport Utility to the Inbound rules of Win 7 Firewall
    While poking around my Network Sharing and Firewall settings trying to figure this out, I got a Pop-up recommending I do that.  AND I did that. Oh, and while you are at it, make sure you have a Home network established. 
    2.) Next, on a hunch, I installed a USB Wi-Fi Adapter (under $20) to my Win PC, enabled that Wi-Fi connection and disabled my Ethernet connection.  I was getting no where on this matter with my Ethernet connection to a DSL Gateway.  But with a Wi-Fi connection to my AirPort Express Base Station, I made progress.
    3.) Finally, while poking around my Network Sharing Center some more, one by one I started the various network device Setup Wizards in there, and Trouble Shooters, to find the elusive TC/USB devices in question...AND voila, it worked.   And it's stable, been this way for going on two weeks now.
    Good luck.

  • Can Time Machine back up a USB Drive connected to Airport Extreme?

    If I connect 2 USB drives to an Airport Extreme via a USB hub, can I use Time Machine to back one up to the other? I've found multiple discussions about how to use an Airport Extreme disk as a Time Machine backup disk, but nothing on this. I want to use one disk as network storage (i.e. use the Airport extreme as a NAS), but I need a backup solution for that disk.

    That's disappointing. I actually have a separate NAS already, configured for RAID1: a ZyXEL NSA220. Worked fine when I only had windows machines, but isn't reliable with my MACs, and doesn't support extended journaled format, so I need a different solution. I was hoping to just use a USB drive attached to my airport extreme to replace it, but I can't do that if I can't back up that USB drive.
    Can anyone recommend a good backup solution? Surely this can't be that uncommon a scenario?

  • Can't Delete Files on USB Drive Connected to Airport Extreme

    I'm trying to delete some files on a USB drive connected to my Airport Extreme, but I keep getting a error message that I don't have sufficient privileges to do so. I've tried super deletion applications like FileXaminer, without any success. What other methods are there?

    Thanks for the info.
    Were you using the drive for Time Machine backups, by chance? Time Machine backups are stored in a different format when the disk is connected directly to a computer. So, you won't be able to continue to use the old backups when the drive location is changed.
    You might want to check the drive by connecting directly to your Mac and running Disk Utility to "Verify Disk" and "Repair Disk" if indicated.
    Even if the drive has it's own power supply, a powered USB hub is usually needed on the AirPort Extreme because the power at the USB port is quite limited.
    Message was edited by: Bob Timmons

  • USB drive connected to Airport Extreme becomes read-only

    Hello
    I have a USB drive connected to my Airport Extreme 802.11n (2nd generation, firmware v7.6). To access the drive, I've set secure shared disks to "with accounts" then defined a user account with read/write access. I connect to this drive using two Windows 7 SP1 64-bit computers.
    Reading and writing to the disk is fine. However, after a day or so, I can read from but cannot write to the disk! I then have to restart the USB drive to write to it again. This has been happening for a while.
    Also connected to the Airport Extreme (using Ethernet) is a Lacie NAS drive (which runs a cut-down version of Linux). This works fine: I've never had any problems with it! It too is password protected.
    Please help!
    Thanks
    Praful

    Tried what you suggested last night - no change. What is odd, though, is that I can create a new folder on the external USB HDD (through the Hub) and copy a file into it. While I can then close Finder, re-open and see the Folder and file I copied, I still can't see all the data that is currently stored on the drive...Is this a delete and re-copy scenario?
    Thanks!

  • USB drive connected to airport i cant see it??

    Hello all, i have an airport extreme. network is all setup fine. I have a USB drive connected to the airport setup for timemachine backups. What i would do is turn it on every week for the day and all my mac would backup to it. Last night i turn it on for my backups and none of my macs seems to be able to find it. Well today right out of the blue the imac suddenly sees it and runs a backup. But i cant see it with the macbook pro. I double checked the setting on the airport and dont see anything out of place. I can however see the drive in finder but when i click on it system tells me it cant connect. Any suggestions?

    WesternCanuk wrote:
    Apple is now forcing me to purchase a time capsule as they do not support puggin in a USB drive.
    it's not new. this information has been available for some time.
    Now this worked perfectly
    it did (and does) so for many users. it just means is that, if you run into problems (as you do now), there will be no support from Apple.
    I now have to physically connect my usb drive to each of my computers to have them back up?
    no. you'd connect the drive to one machine and let the other Macs back up to it via your network.
    printer i suppose ?
    yes. and HD's for sharing files across your network - just not for TM backups !
    JGG

  • Cannot Delete Folders from USB drive connected to Airport Extreme

    When I try to delete files from the usb drive connected to my airport I get "cannot remove folder, the directory is not empty.
    This only happens for some of the folders that are empty. No problem deleting any files whether they were created before or after I setup the airport. The folders that won't delete were created after I hooked up the drive to the airport however, I can make new folders and delete them no problem now. The ones that don't delete say "read only" in the properties. when I uncheck read only it reverts back to read only automatically.
    Any ideas what might be causing this?

    Tried what you suggested last night - no change. What is odd, though, is that I can create a new folder on the external USB HDD (through the Hub) and copy a file into it. While I can then close Finder, re-open and see the Folder and file I copied, I still can't see all the data that is currently stored on the drive...Is this a delete and re-copy scenario?
    Thanks!

  • Accessing a USB drive connected to Airport Extreme over Internet

    Hello!
    I have an iPad, I have an Airport Extreme with a USB drive connected and I have a MobileMe account.
    And I'm aware that as yet there's no Back To My Mac for iPad.
    Is there an easy way on the iPad to connect remotely to the USB drive, over the Internet?
    I don't want to have to leave my MacBook Pro on whilst I'm travelling.
    I've looked at Logmein and Filebrowser and iTeleport and can't find a way to do this.
    Has anyone managed to suss this???
    Many thanks....

    I am not ware of any way of doing what you want since, to my knowledge, the AE does not function as a server to "serve" the contents of a connected USB drive. I have a LaCie NAS and that NAS includes a FTP server that I can access via my iPad via AirSharing HD.

  • Time Machine doesnt see my USB drive, connected to Airport extreme =(

    Hello,
    I've been trying to figure this one out for almost 3 weeks now, but with no luck. I have a usb hard drive, connected to airport extreme. I've clicked on "setup time machine", select "choose disk", there is no disk to select. So I click on the "set up time capsule, it takes me to airport utility. I then click on the "disk" button and file sharing is enabled.
    I can mount the disk through the finder, just fine and able to transfer files back and forth, however time machine cant seem to pick up the drive. Would love to be able to use time machine to do backups, So can someone please help?
    osx 10.5.5 with airport utility 5.3.2
    Thanks in advance!

    Well this has worked for me. I have a Freecom 500Gb usb hard Drive connected through an unpowered 4-way USBhub to an Airport Extreme Base station. After mounting the Air Disk hard drive on my powerbook, I then dragged the disk to my user folder, thereby creating an alias. I have put that alias in my login items and now TimeMachine works beautifully. I've repeated it on a Mac Mini (also using OSX 10.5.5) and that seems to be fine too. Admittedly the back-ups take a long time over airport, but fine via Ethernet.
    Good luck everyone who struggles with this.
    David

  • Using Spotlight to search USB drive connected to Airport Extreme base stati

    Hi all,
    I successfully connected a USB hard drive to my Airport Extreme base station (the drive has its own power supply; when I tried connecting a USB-powered drive, it wouldn't show up). However, I find that I cannot search the USB hard drive over the Airport network. That is not very convenient, to say the least. Is this possible without paying $500 for Snow Leopard server software or waiting for Lion (with a rumored built-in server function) to arrive?
    Thank you!

    My last response was incorrect. The base station is in the finder window, under "Shared." I click on that and then I see the USB driver. Also, I went to finder prefs and clicked to show servers on the desktop. So now the USB drive connected to the base station shows up on my desktop. But I still can't search it.
    Thanks again.

  • Automatically open USB Drive (connected to Airport Extreme) in Finder

    I have a 1TB USB drive connected to my Airport Extreme (version 7.6.3).
    File sharing is enabled in the Airport-configuration program.
    But I liked to have this USB drive displayed (automatically) on the desktop. Same as is happening with the harddisk.
    So I don't have to manually open the networ, Airport Extreme station and the USB drive (see picture below).
    Does anyone have a suggestion ?
    Thanks in advance.

    Thanks Bob.
    I noticed that the USB drive is displayed with a different icon. Below the icon if I use the automatic connection as you have suggested.
    And if I connect it manually I get the belowlisted icon.
    What is the difference between those ?
    And is there a difference in performance or capabilities ?
    Thanks in advance.

  • USB Drive Connected to Airport Extreme:  I can see, but can't access

    Connected one printer and two USB hard drives through USB hub to Extreme. Printer works ok. Both Drives are visible in Finder, but won't show files. Tried to copy files through Finder to each USB drive and got an "Error Code 8058". Tested each drive directly to Mac and worked fine, so it's not a drive compatibility problem. Thoughts on what may be wrong?

    Tried what you suggested last night - no change. What is odd, though, is that I can create a new folder on the external USB HDD (through the Hub) and copy a file into it. While I can then close Finder, re-open and see the Folder and file I copied, I still can't see all the data that is currently stored on the drive...Is this a delete and re-copy scenario?
    Thanks!

Maybe you are looking for