Can LMS 3.2 manage cisco SM-ES3-24-P which is a switch/router module inserted into a 3945 Router?

LMS 3.2 on Solaris 10
LMS properly manages our 3950 routers, but we recently installed a cisco SM-ES3-24-P (PowerPC405) processor. This is managed via it's own IP address. I recently added this to our LMS system and ran an update inventory job. The job succeeded, see attachement, however the device is still listed as Unknown. I recently updated all RME device packages, about two weeks ago. I'm assuming there isn't a device package for this type of module yet?
Thanks,

Hi,
These kinds of Modules are supported in LMS 3.2 as per the below link . Check this link and look for -->
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/device_support/table/lms32sdt.html
1.3.6.1.4.1.9.1.1053
It also mentioned what should be the minimum IOS version and this module is supported for what functionality in CiscoWorks.
Thanks,
Gaganjeet

Similar Messages

Can LMS 3.2 manage a 3560E with the new cisco SM-ES3-24-P cards installed?

LMS 3.2 on Solaris 10
The 3560E was previously managed by LMS, but I just added a cisco SM-ES3-24-P card into it.
This is a 24 port switch/router module that sits inside a 3945 router.
As of now, LMS considers this a separate device (b/c I added it as a new device) but it's Unknown.
I ran inventory collection on it and the job succeeded. I'm attaching the output from this job.
So it is able to talk to it, but I'm guessing there isn't a device package out there for it yet? I just updated all of the RME device packages about two weeks ago.
Thoughts?
Thanks,

FYI...I opened a TAC SR on this and they suggested I check for new Common Services device packages. I applied the two packages listed on the attachment.
I'm not sure which package did the trick, but this device is now recognized via LMS.
Thanks,

How Can I Set an Application on a USB Drive to Automatically Open When the Drive is Inserted Into a Mac?

The title pretty much says it all. But if you don't understand, here is an example of what I want to happen:
When a USB drive is inserted onto my Mac, an application on it will open.
How can I make this happen?

I haven't tried it, but perhaps a Watched folder on the external drive & an Applescript?
http://www.mactech.com/articles/mactech/Vol.20/20.07/FolderWatching/index.html
Or perhaps just an Applescript to check for exist :USB Drive Name, then run application?

NM-16ESW - adding a switch into a 3725 router slot - can i route traffic out of the switch ?

Hi all,
I have added the above module R16#show ip int br
Interface IP-Address FastEthernet0/0 unassigned FastEthernet0/1 unassigned FastEthernet1/0 unassigned FastEthernet1/1 unassigned FastEthernet1/2 unassigned FastEthernet1/3 unassigned FastEthernet1/4 unassigned FastEthernet1/5 unassigned FastEthernet1/6 unassigned FastEthernet1/7 unassigned FastEthernet1/8 unassigned FastEthernet1/9 unassigned FastEthernet1/10 unassigned FastEthernet1/11 unassigned FastEthernet1/12 unassigned FastEthernet1/13 unassigned FastEthernet1/14 unassigned FastEthernet1/15 unassigned Vlan1 unassigned R16(config-if)#int fa1/0
R16(config-if)#ip address 192.168.10.1 % IP addresses may not be configured R16(config-if)#
q1) Not being able to set IP q2) in that case, since the Assuming fe0/1 on the router and 2 workstations attached Regards,
Noob (16 switch port) into my router.
OK? Method Status Protocol
YES unset administratively down down
YES unset administratively down down
YES unset administratively down down
YES unset administratively down down
YES unset administratively down down
YES unset administratively down down
YES unset administratively down down
YES unset administratively down down
YES unset administratively down down
YES unset administratively down down
YES unset administratively down down
YES unset administratively down down
YES unset administratively down down
YES unset administratively down down
YES unset administratively down down
YES unset administratively down down
YES unset administratively down down
YES unset administratively down down
YES unset up down
255.255.255.0
on L2 links.
to the interface as shown above, I would believe it is really a switch port. Is there anyway I can see what kind of port a interface is or can be ? (switch port, routed port etc ?) or whether is it a L2 or L3 switch ?
switch is already inside the router, how do i route L3 traffic out of the switch ?
is the interface connected to external network.
to the switch ports fe1/1 and and fe1/2, how can i set their gateway to point to fe0/1's IP ? Can fe0/1 to be connected to fe1/0 internally ?

Hi KOE SIZE JIE,
q1) I tried the no switchport command on the 16switch port module and it works. I can set an IP on the switch port. But according to Liam, it is a L2 switch, how come we can assign no switchport command ?
As Bilal pointed out, I was mistaken you can issue the "no switchport" for a L3 routed port on that specific module.
q2) it is said that on a L2 switch only 1 SVI can be connected (for management purpose only) and L2 switch is not able to do routing. With the L2 switch module inserted into the router, will the SVI be able to do routing then ?
I believe this goes back to what Bilal was saying about limited functionality on the EtherSwitch. I will have to play with one in GNS3 to give you a solid answer.
But I think what it is trying to say is... You cannot use SVI's for inter-vlan routing. You can only have a single SVI for management purposes.
q3)Liam, you mention earlier fa0/0 is pointing to some network. is fa0/0 in the same router as the 16 switchport module ?
ip route 10.10.10.0 255.255.255.0 192.168.1.254 -- this command seems to be saying to access the 10.10.10.0 network, please go to the next hop IP 192.168.1.254 (but again, you are setting this next hop IP on the current router interface itself) - did i get anything wrong ?
I have read back my post and this reads wrong.
When i showed you the code snippet, 192.168.1.254 would be the interface on the next hop router. Not the router you are issuing the ip route command on. You would also need an IP address on the router interface directly connected to the next hop router. I.E 192.168.1.253
You will not then receive that error. Sorry about that, my sloppy config without a diagram!
HTHs,
Liam

How many domains can Prime Collaboration Advanced manage with the BE6000?

The BE6000 Administration guide states that "Most BE6K deployments have a single domain as part of a Standard Prime installation. Multiple domains are available with Prime Collaboration Advanced (available for purchase) that can be used for complex Business Edition 6000 deployments."
How many domains can Prime Collaboration Advanced manage with the BE6000 solution? How do we order and deploy Prime Collaboration Advanced with the BE6000 solution?

http://docwiki.cisco.com/wiki/System_Capacity_for_Cisco_Prime_Collaboration_10.0

Upgrading from LMS 4.1 to Cisco Prime Infrastructure

Looking for some information and confirmation on the upgrade process.
Currently we are running LMS 4.1 with a valid SAS Service Contract which will allow me to upgrade to Prime Infrastructure 1.1 or Prime Infrastructure 1.2 using the upgrade tool at no charge. After using the tool I am given access to download PI1.1 or PI1.2, however, it only actually let me download PI1.1 but said i do not have the proper permissions to download the 1.2 license. I also noticed that the software images for 1.2 are not available ont he ciso download page.
I am wondering what the latest version of Prime Infrastructure I will be able to upgrade to without an additional purchase. Can I upgrade up to all the way up to 1.4 or can I only go up to 1.2 (but then where is the download for the software).
If i can upgrade to 1.4 then what path should I take? 1.1 to 1.3 to 1.4? Just skip 1.2 since the download is not available and it will not let me download the license file?
Thank you for your help

LMS 4.x to Prime 1.x would not be considered a functional or recommended "upgrade" for most intents as you would lose several major capabilities (Topology, Ciscoview, many reports, compliance templates, etc.). Your best path right now would be to move your LMS along to the current version - 4.2.4. The release notes explain the upgrade path for that.
Licensing and upgrade eligibility-wise you need SASU for PI (not plain SAS for LMS) for major upgrades (i.e to go to 2.0). An LMS SAS contract entitles you to migrate to PI 1.2 which in effect means 1.3 although Cisco had some issues with updating the ordering system so there was not actually a SKU for PI 1.3 sold - only the 1.2 version which, when combined with your LMS SAS service contract, entitles you to move to PI 1.3 (or 1.4 but that's not generally recommended). More details are in the Prime Ordering and Licensing Guides here.
Personally, I recommend customers with existing LMS 4.x installations wait until PI 2.1 comes out to consider the upgrade. 2.0 still misses several tools present in LMS 4.x.
If you really want to move over to PI, you can export the data from LMS 4.2.4 and import into PI 1.3 (or 2.0).

Migrating from CiscoWorks LMS 3.1 to Cisco Prime LMS 4.2

Hi Everyone
My client was formerly having CiscoWorks LMS 3.1. Recently, they purchased Cisco Prime Infrastructure v1.2, which comes with Cisco Prime LMS 4.2. Can I migrate the database (equipment list, usernames etc.) of the CiscoWorks LMS 3.1 to Cisco Prime LMS 4.2? If yes, how do I do this? Please kindly advice.
Shown below, were the Part Numbers quoted to the end client.
R-PI12-UP-K9
LMS 2.x/3.x to Cisco Prime Infrastructure 1.2 Major Upgrade
L-PI12-LF-1.5K-LIC
Prime Infrastructure 1.2 - Lifecycle - 1.5K Device Lic PAK
L-PILMS42-1.5K-U
Prime Infrastructure LMS 4.2 - 1.5K Device Maj Upg Lic
R-PI12-BASE-K9
Prime Infrastructure 1.2 Base License and Software
L-PI12-1.5K-UP
LMS 2.x/3.x to Prime Infrastructure 1.2 Maj Upg 1.5K Device
Regards,
Ram

Thanks Marvin for your advice. Just one last question, there's a statement in the URL that you've provided
"Ensure that the passwords, HTTPS port and SMTP server details are same in both LMS 3.2 SP1, LMS 4.0.1 or LMS 4.1 server and LMS 4.2 server with Symantec Veritas implementation, while migrating data from non-HA to HA environment."
Does this mean my client need to purchase Symantec Veritas, as well?

QOS on Cisco 1841 between MS TMG and managed Cisco 1841?

Replicating our VM data from our Site A to a Hosted Provider (Site B) for DR purposes.
Crude annotaion of our network:
VIRTUAL HOSTS-----NORTEL L3 SWITCH-----MS TMG 2010 EDGE FIREWALL-----ISP MANAGED CISCO 1841-------------------CLOUD---------------SITE B
At times the replication traffic is hogging the connection and causing degraded performance for VPN clients amongst other things.
TMG 2010 doesn't support QOS and we cannot make any changes to the ISP managed Cisco router, nor can we request changes to be made.
My plan was to get a hold of a small switch that supported QOS and place this between the MS TMG and the managed router but we actually have another Cisco 1841 sitting doing nothing, would I be able to use the spare 1841 for this purpose?
Many thanks
Steve

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
10 Mbps is around the limits of an 1841. It might or might not have enough capacity. You could try using it and monitor its CPU when it's dealing with saturated 10 Mbps.
You can police or shape before the 10 Mbps bottleneck. That will insure you can guarantee bandwidth for the non-replication traffic.
You can only police after the 10 Mbps bottleneck. If the replication traffic is TCP based, dropped packets should slow the sender, but the sender can often still burst saturate the link before it detects the drops and slows. If you set a very low bandwidth allowance for the replication traffic, you can often keep it from burst saturating the link. The other issue with policing, it cannot dynamically allow bandwidth utilization (i.e. prioritization) as you can do with a shaper.
If most of the replication traffic bandwidth consumption is one way, insert the 1841 anywhere upstream (where all traffic will pass through it) of the 10 Mbps bottleneck, and shape or police. I would recommend shaping with a very low bandwidth allowance for replication (e.g. 1%). This will allow replication traffic to use all 10 Mbps, but any other traffic will get priority.
If the replication traffic bandwidth consumption is two way, you'll really want a 2nd device, on the other side of the bottle neck.
PS:
BTW, in lieu of shaping, having your upstream (of bottleneck) also with a physical 10 Mbps interface works even better. Again, de-prioritize the replication traffic.
e.g.
class-map replication
match
policy-map phy-10m
class replication
bandwidth percent 1
(optionally random-detect)
class class-default
fair-queue
int 10m
service-policy output replication

Upgradding Prime Infrastructure version 1.2 and LMS 4.x to Cisco Prime Infrastructure 2.0

Hello,
A customer currently have 2,500 Cisco Prime Infrastructure Lifecycle device license using Prime Infrastructure version 1.2 and LMS 4.x. the customer wants to upgrade to Cisco Prime Infrastructure 2.0.
Does anyone know if it is possible to upgrade to version 2.0 without additional cost? the licenses from
Cisco Prime Infrastructure 1.2 has to be upgraded or we need only to rehost the VUDI.
Also could be possible to upgrade LMS 4.x to Cisco Prime Infrastructure 2.0?
thanks!

The two features you mention are two big missing ones. Another is full syslog capability. I don't believe CiscoView or day one support via package updates is included either.
Another is less tangible - the depth of experience and documentation available for LMS vs. Prime Infrastructure (particularly the wired management features). I agree for wireless PI 2.0 looks good. Some new features are coming for wired that look promising but they are new as of PI 2.0 so I'm taking a wait and see on them.
I hope to get 2.0 up in my lab in the next week or so and will hope to be pleasantly surprised but that's seldom the case with a major new release.

Can not refresh server manager Error:0x8007045b

OS: Windows 2012 R2 Core
Services: Hyper V
I was trying to remote reboot and the session hung. No worries I decided I could just reboot the next morning. So I rebooted the next day but when I go into server manager I get
an errror can not refresh server manager Error:0x8007045b. Did some research found suggestions to fix it using a DISM.exe /Online /Cleanup-image /Restorehealth.
But then I get an error 1115 A system Shutdown is in progress. I attempt to fix this issue using pskill winlogon but the issue pursistest. I have restarted the server several times now. Not sure how to fix this.
Thanks in advance,
Jake

Hi,
In addition to the above information,
Checkout the below thread for similar discussion,
http://social.technet.microsoft.com/forums/windowsserver/en-US/a700e9f6-4491-4c70-8bd0-d9d3111e2f70/windows-reboot-error
Regards,
Gopi
JiJi
Technologies

JMStudio Error "Can not create session manager"

Hi,
I'm trying to transmit an mpg file through a simple pc to pc network, using the transmission wizard in the JMStudio, and everytime it causes a "can not create session manager" error, even when I try to transmit .mp3 file
I'm using an ip like 100.100.0.1 for the sender machine, and 100.100.0.2 for the receiver machine, and I don't know where is the problem
thanks in advance

Um,maybe the port that you use for transmission is already occupied.
Make sure that you are not using JMStudio to transmit streams while trying to receive streams from the same port.

Can not login access manager

mail server version is JES messaging Server 6 2005Q4 :
My Access Manager:http://hostname:8080/amserver
last week, i login access manager, under the web label or configuration label�F
in "ldap" item�Ci add new dc=xx,dc=xx,dc=xx�C
then save configuration.
but after that i can not login access manager.
when i user admin login,it print:"
Authentication failed".
what should i do to restore access manage?
thanks!

javatoall wrote:
Hi,
I login Access Manager, access sample "realm" -> Authentication->
Advance Properties -> User profiles and then I choiced "Dynamic with user Alias".
Then I only configure JDBC authentication with mysql database that I don't used ldapservice.
When I created a one new user in MySQL, I can login into web application that i security as "sample.war" successfull but new user don't right access resource that i protected before.
When i login access manager with amdmin user, I can not find user that i has been created it in MySQL database. t
When the users are created through the dynamic profile, the default cn/sn are set to "default" , after creation you need to login to amconsole as amadmin and change/add proper values for these attributes.
Alternatively you can set the protected resource's policy subject to Authenticated users. This will work but not sure will meet your requirement
>
When i login access manager console with new user, it login successful, and view Profile of new user that I has been created.
Can you tell me How to manage new user that I has been new in MySQL by Access manager console ?
I want to configure access proteced resourse for that user. How to configure that ?
read above use the authenticated users subject
Thank for every help.
VinhND.

Can not locate Workgroup Manager; possibly not installed?

Here's the story:
I'm trying to get my new camera software installed and one of the steps is to launch Image capture.
Image capture gives me an error saying: "No Image Capture Device connected."
Apple says to fix this I need to open Workgroup Manager (in /Applications/Server/) and change some preferences.
But, I can not find Workgroup Manager for the life of me. I used spotlight with no luck. I also don't have a folder in Applications titled Server. This worries me and makes me wonder if the program could have been deleted or not installed at all?
Any suggestions on how to find WgM would be welcome.

Whoa... somebody got confused someplace... I wouldn't guess you are running OSX Server on a MacBook, but the oSX CXlient instead, so no idea how Apple came up wih that solution.
You likely should not have a Server folder there, nor the APP they speak of.
What kind of Camera exactly, and how does it connect?

Can not start Enterprise Manager web page

I can not start Enterprise Manager web page.
Here is my steps:
1. Start enterprise manager
emctl start
Waiting for EM to initialize ...Started
2. Check status:
emctl status
EMD is up and running : 200 OK
3. Start the web page
http://myhost:1810/
4. get following error
"There was no response. The server could be down or is not responding"
System info:
Database: 8.1.7.2
OAS: 9.2.0.2
JDK: 1.3.0_02
Server OS: SunOS 5.8
My question is where is the log file of enterprise manager and what the problem is.
Thanks in advance
Don

diego,
Thank you for your help. when I try your command I get following error:
emctl start iasconsole
Unknown command option
Usage::
emctl start|stop|status
emctl reload | upload
emctl set credentials [<Target_name>[:<Target_Type>]]
emctl gencertrequest
emctl installcert [-ca|-cert] <certificate base64 text file>
emctl set ssl test|on|off|password [<old password> <new password>]
emctl set password <new pwd>
emctl authenticate <pwd>
emctl switch home [-silent <new_home>]
emctl config <options>
emctl config options can be listed by typing "emctl config"

Can not connect computer to Cisco Connect -EA3500

Can not connect computer to Cisco Connect -.Receive error msg 82BD0305. Reset to EA3500 to default and reinstalled software.

Reading the manual it says the username is blank, password 'admin'.

Can LMS 3.2 manage cisco SM-ES3-24-P which is a switch/router module inserted into a 3945 Router?

Similar Messages

Maybe you are looking for